REPAIR AND MAINTENANCE OF OLD RCC,GI,CI,DI PIPE LINE AND ALLIED SERVICES UNDER GE SAUGOR

Amount

Excavation in trenches in hard/dense soil not exc 1.5m wide & not exc 1.5 deep and getting out in hard/dense soil complete all as per specified and directed

Removing excavated material outside MD not exc 50m and depositing where directed at a level in not exc 1.5m above the starting point in soil complete all as per specified and directed

Returning filling in including spreading , levelling watering and well ramming in layers not exceeding 25cm complete all as per specified and directed

Supplying and laying GI tubing , medium grade galvanised with all fittings,specials such as bend, elbows,tees, short pieces connection, back nuts, diminishig pieces, caps, plugs and unions etc laid in trenches or ceiling including taking up or down of old GI tubing and connections for the following sizes:- (Note:-Excavation and earth work will be measured and paid separately)

15mm bore

20mm bore

25mm bore

40mm bore

50mm bore

80mm bore

Taking down & re-fixing/re-laying/re-routing only of GI tubing for the following sizes after cleaning in same location or other location new or old position , in trenches, in walls, ceiling and floor & testing complete all as specified and directed. Note- (i) GI fittings shall be measured and paid under relevant items (ii) Excavation and earth work will be measured and paid separately

15mm bore

20mm bore

25mm bore

40mm bore

50mm bore

80mm bore

Supplying and laying GI tubing, medium grade galvanised with all fittings such as bend, elbows,tees, short pieces connection, back nuts, diminishig pieces, caps, plugs and unions laid in floor/fixed to walls with suitable clamp with wooden plug alongwith screws in intervals including taking up or down of old GI tubing and connections for the following sizes:- ( Note: Excavation and earth work will be measured and paid separately)

15mm bore

20mm bore

25mm bore

40mm bore

50mm bore

80mm bore

S&F Gun metal globe valve with iron wheel, screwed both ends for iron pipes approved including taking down exisitng unserviceable Gate valve complete all as specified and directed of following sizes:-

15mm dia

20mm dia

25 mm dia

40 mm dia

50 mm dia

S&F sluice valve the following sizes CI body ISI marked class PN 1.6 heavy duty flanged ends cast iron wheel with Brass spindle (ISI marked) conforming to IS : 14786 – 2000, short body including nuts ,bolt, washers and gasket including taking down of existing unserviceable sluice valve from the existing pipe line complete all as specified and directed:- ( Note: Quoted rate deemed to be included for making good the damaged valve chamber)

100 mm dia

150 mm dia

Supply, laying, connecting, jointing and testing Centrifugally cast ( Spun ) Ductile iron Pressure pipe ISI Marked confirming to IS-8329-2000 ( Reaffirmed -2005 Edition 4.1 ) of following size with socket spigot ends, suitable for "Push on Joints ( Tyton Joint )" each standard working lengths supplied with rubber gaskets duly ISI marked for water supply, Class K-9 with socket with cement mortar lining inside and metallic Zinc coating with finishing layer of bituminous paint on outside the pipe with out polythylene sleeves but including "Push on Joint" supplied with ISI Marked EPDM rubber gasket conforming to IS-5382-1985 ( reaffirmed-2003 ) laid in trenches including taking up RCC water mains complete all as specified and directed of following sizes:-

100 mm bore.

150 mm bore

Supply, laying, connecting, jointing and testing Centrifugally cast ( Spun ) Cast iron class LA B marked confirming to IS 1537 -1976 with socket spigot ends, suitable for Tyton Joint each standard working lengths supplied with rubber gaskets duly ISI marked for water supply with socket with "Push on Joint" supplied with ISI Marked EPDM rubber gasket laid in trenches including taking up old RCC water mains complete all as specified and directed by Engineer-in-Charge of following sizes.Make: Electrosteel / TATA / Jindal.

Supplying, laying, connecting, jointing and testing Centrifugally cast ( Spun ) Ductile iron Pressure pipe ISI Marked confirming to IS-8329-2000 ( Reaffirmed -2005 Edition 4.1 ) with socket spigot ends, suitable for "Push on Joints ( Tyton Joint )" each standard working lengths supplied with rubber gaskets duly ISI marked for water supply, Class K-9 with socket with cement mortar lining inside and metallic Zinc coating with finishing layer of bituminous paint on outside the pipe with out polythylene sleeves but including "Push on Joint" supplied with ISI Marked EPDM rubber gasket conforming to IS-5382-1985 ( reaffirmed-2003 ) laid in trenches including taking up old cast iron water mains (including all fittings) with spigot and socket ends and rubber tightning joints including burning out lead joints if any and recoving lead complete all as specified and directed by Engineer-in-Charge of following sizes:- ( Excavation and earth work will be measure and paid seperately)

300 mm bore

350 mm bore

Supplying, laying, connecting, jointing and testing of Ductile iron pipe fittings ( Specials ) heavy duty for any type ( flanged / socketed ) pipes such as, bends ( any type radius, and angle ), tapers, any type straight bend, increasing, decreasing or double socket etc. Tee pieces, ring branch, Y junction, double branch, cross ( all socket or socket and spigot ), collars, caps and plugs, adapters etc. of any size radius and length conforming to IS 9523 / 2000 specifications with external bitumen coating and internal cement mortor lining and metallic zinc coating of size upto 350 mm bore complete all as specified and directed.

Supplying, laying, connecting, jointing and testing of Cast iron pipe fittings ( Specials ) heavy duty for any type ( flanged / socketed ) pipes such as, bends ( any type radius, and angle ), tapers, any type straight bend, increasing, decreasing or double socket etc. Tee pieces, ring branch, Y junction, double branch, cross ( all socket or socket and spigot ), collars, caps and plugs, adapters etc. of any size radius and length upto 150 mm bore complete all as per specified and directed.

All as per Srl item No.13 above but 200mm to 300mm bore

M&L for cutting of bituminous road/floor/plinth protection for laying pipe not exceeding 1.5mm and 1.5 depth and making good with PCC including refiling with excavated material and watering well ramming/compacting complete all as specified and directed. Note:-PCC shall be measured and paid separately

M&L for PCC 1:2:4, type B 1 (using 20 mm graded stone aggregates) as in filling and making good disturbed surface complete all as specified and directed

Removal of detoriated valve chamber cover and providing with new MS frame work made of 25 x25 x 3mm angle iron complete and top cover made out of 3.15 mm hick MS sheet duly hinged with frame including grouting / fixing into wall chamber and painting with two coats of enamell paint over a coat of red oxide and locking arrangement , lifting hook etc complete all as specified and directed

M&L for repair of valve chambers by preparation of brick surfaces including rendering in CM(1:4) , 10mm thick of fair face of brick work.complete all as specified and directed

M&L for construction of brick masonary valve chamber chamber of 1200mmx 1200mm x 1200mm size (inside) for sluice valve with CI wheel valve with bricks of subclass B in cement mortar 1 :4 (1 cement : 4 fine sand), 12mm thick, Inside plastering in cemtn mortar 1:4 finished with a floating coat of neat cemtne, foundation concreate in 1:4 :8 type D2 (using 40mm graded stone aggregates) and with angle iron frame of size 40mmx40mmx5mm & 3mm thick MS Sheet cover with locking arrangement including necessary excavation & earth work complete all as specified and directed

All as per Srl item No.19 here in before but 1000mmx 1000mm x 1000mm size.

All as per Srl item No.19 here in before but 900 mmx 900 mm x 900 mm size.

All as per Srl item No.19 here in before but 600 mmx 600 mm x 600 mm size.

All as per Srl item No.19 here in before but 600mmx600mmx 400mm size.

All as per Srl item No. 19 here in before but 900 mmx 900 mm x 600 mm size.

All as per Srl item No. 19 here in before but 1500mmx 1500mm x 1000mm size.

All as per Srl item No. 19 here in before but 1200mmx 1200mm x 1000mm size.

M&L for water pipe line route indicator duly engravd with "PIPE LINE MES" made out of pre-cast RCC (1:1.5:3) type A1 (using 12.5mm graded stone aggregates) of size 120 cm height 15cmx15cm cross section at bottom tapered to cross section 10cmx10cm at top duly reinforced with 4 Nos 10mm dia TMT main bars and 8 mm dia TMT bar as in stirrups @ 150mm c/c complete all as specified and directed. Note:- Excavation and PCC work shall be measured and paid seperately

Opening the top of the sluice valve carefully, taking out the gate & spindle, scraping/cleaning the gate both sides, cleaning/scraping of sluice valve body throughly from inside, refixing / replacing the spindle, gate cheak nut and top of sluice valve including replacement of gland packing rope of suitable size & rubber gasket and bolt, nut with washers necessary metalling ,grinding and levelling of the valve door seating complete for the following sizes of sluice valve :- ( Note:- Replacement of check nut/ spindle, etc shall be measured and paid separately under relevant items)

80 mm dia.

100 mm dia.

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Supply only spindle stainless steel suitable for following size CI sluice valve :-

80 mm dia.

100 mm dia.

150 mm dia

200 mm dia

250 mm dia

300 mm dia

Supply only sluice valve check nut Gun metal as per sample (Square/rectangle) of following size :-

80 mm dia.

100 mm dia.

150 mm dia

200 mm dia

250 mm dia

300 mm dia

M&L for run lead joint for spigot and socket pipes and fittings including taking out the unserviceable lead joints including spun yarn and of the following sizes:-

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

Taking up and relaying/re routing only cast iron mains ( including all fittings) with spigot and socket ends , tyton joint and lead joints for the following sizes. Note: Lead Joint and Tyton Joint shall be measured under relevant items

80 mm dia

100 mm dia

150 mm dia

200 mm dia

250 mm dia

S&F in replacement ball valve (Float valve) high pressurre of PTMT with epoxy coated Aluminium tod& high density plastic ball screwed for iron pipe and fixed (Mini Weight 15 mm -142 gms) of size 15 mm dia complete all as specified and directed

All as per Srl item No.33 here in before but 20 mm dia (Ball weight 210 gms)

Supply only following items:-

GI Socket 15 mm

GI Union 15 mm

GI Elbow 15 mm

GI Socket 20 mm

GI Union 20 mm

GI Elbow 20 mm

GI Pipe Nipple 15 mm dia 3" long

GI Pipe Nipple 15 mm dia 6" long

GI Pipe Nipple 20 mm dia 3" long

GI Pipe Nipple 20 mm dia 6" long

GI Pipe Nipple 25 mm dia 3" long

GI Pipe Nipple 25 mm dia 6" long

GI Tee Equal 15 mm dia

GI Tee Equal 20 mm dia

GI Tee Equal 25 mm dia

GI Socket reducer 20x15 mm

GI Socket reducer 25x15 mm

GI Socket reducer 25x20 mm

CI Flange 80 mm dia with 04 no of bolt,nut with washers

Shelloc Bottle 50 ML

Cotton thread Roll

MS Bolt,nut with washers in different sizes and length complete all as specified and directed

GI Bolt,nut with washers in different sizes and length complete all as specified and directed

Hacksaw blade one side cutter complete all as specified and directed

GI Plug 15 mm dia (Inner /outer thread)

GI Plug 20 mm dia (Inner /outer thread)

GI Plug 25 mm dia (Inner /outer thread)

GI Plug 40 mm dia (Inner /outer thread)

GI Plug 50 mm dia (Inner /outer thread)

PVC Stop Cock 15 mm dia Make: Prayag/Leader/Supreme

PVC Stop Cock 20 mm dia Make: Prayag/Leader/Supreme

PVC Stop Cock 25 mm dia Make: Prayag/Leader/Supreme

Led Pig

MS Clamp not less than 5 mm thick split type and necessary drilling/welding GI socket as per site requirement alngwith two nos of GI Bolt,nut with washer suitable for CI/DI 80 mm dia water pipe line

All as per Srl item No.35.34 here in before but 100 mm dia

All as per Srl item No.35.34 here in before but 150 mm dia

All as per Srl item No.35.34 here in before but 200m dia

All as per Srl item No.35.34 here in before but 250 mm dia

All as per Srl item No.35.34 here in before but 300 mm dia

S&F in replacement self priming monoblock pump set 0.5 HP Capacity, 230V, SP suitable for 25x25mm suction and delivery line complete. Make: Havells/CG/Texmo/V Guard

Carry out day to day rectification of water supply complaints at Area I & Area II like Leakege of water supply line any sizes, brocken/Crack of the GI/CI/DI Pipes any sizes, replacement of unserviceable Gate valves, replacement of gland rope and rubber packing to any size of Sluice valves etc complete all as directed by the Engineer-in-Charge Note: (i) . Replacement of GI Fittings shall be measured and paid separately. (ii). GI Pipe shall be mesured and paid separately. (iii). If required excavation and earth work will be measured and paid separately. (iv). Materials like Lead,Gate valves, gland rope,rubber packing, Shealloc bottole,cotton thread etc shall be measured and paid separetely (v). Pipe fitter with Helpers so detailed by the contractor will report to MES complaint cell at 08.45 Hrs morning to receive complaints(Complaint slip provided by the contractor) from department and complaint should be rectified with in a same day. (vi). Rate included with transport vehicle provided by the contractor to attending the complaints Area I .(vii). Attending the complaints not less than min four complaints per day

M&L for preparing the surface of MS pipe line of size 50mm bore painting with one coat over painting with one coat of synthetic enamel paint and with one coat over a painting over a surface of existing colour including scrapping out of old fadded paint complete all as specified and as directed

All as per Srl item No. 38 here in before but 100 mm bore

All as per Srl item No. 38 here in before but 150 mm bore

Material and labour for preparing the surface of valve pit chamber MS Cover painting with one coat over painting with one coat of synthetic enamel paint and with one coat over a painting over a surface of existing colour including scrapping out of old fadded paint complete all as specified and as directed by Engineer-in-charge

Material and labour for preparing the surface of Over head Reservoir 18M height MS ladder with railing painting with one coat over painting with one coat of synthetic enamel paint and with one coat over a painting over a surface of existing colour including scrapping out of old fadded paint complete all as specified and as directed by Engineer-in-charge Note : Qouted rate shall deemed to included to provide safety belt / ladder and insurance as required at site.

Dismantling unserviseable existing water level indicator from Over head tank/underground reservoir/UG Sump under GE Saugror and S & fixing FRP scale conventional water level indicator as per site requirement complete with float,wire,float guide pipe,bracket & pully,countor weight,indicator pin etc complete all as specified and directed by Engineer-in-Charge Note : Qouted rate shall deemed to included to provide safety belt / ladder and insurance as required at site.

SHRI RAM ELECTRICALS ENTERPRISES