Command Control Centre at Commission for Air Quality Management (CAQM), 16th Floor, STC Building, New Delhi

Estimated Cost to Put in Tender (ECPT) ₹50,822,806.00

Digitally signed by AMIT

S.H. 1 ELECTRICAL WORK: CAQM , NEW DELHI ESTIMATE

ELECTRICAL WORK

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

A. INTERNAL WIRING

1 1.10 Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm

FRLS PVC insulated copper conductor single core cable in surface / recessed

pvc conduit medium with modular switch, modular plate, suitable G.I box and

earthing the point with 1.5 sqmm. FRLS PVC insulated copper conductor single

core cable etc as required.

2 1.55 Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call

bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated

copper conductor single core cable in surface/ recessed steel conduit, and

earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single

core cable etc. as required.

3 1.7 Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of

FRLS PVC insulated copper conductor, single core cable in surface/ recessed

pvc conduit medium as required

4 1.24 Supplying and fixing following modular switch/ socket on the existing modular

plate & switch box including connections but excluding modular plate etc. as

5 1.27 Supplying and fixing following size/ modules, GI box alongwith modular base &

cover plate for modular switches in recess etc. as required.

a 1.27.1 1 or 2 Module (75 mmX75 mm) Nos. 3.00 0.00

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

6 1.31 Supplying and fixing suitable size G.I box with modular plate and cover in front Each 21.00 477.00 507.19 10,651.08

on surface or in recess, including providing and fixing one 3 pin 5/6 amps

modular socket outlet and one 5/6 amps modular switch, connection etc. as

required. (For light plugs to be used in General purpose).

7 1.32 Supplying and fixing suitable size G.I box with modular plate and cover in front Each 2.00 586.00 623.09 1,246.19

on surface or in recess, including providing and fixing one 6 pin 5/6 & 15/16

amps modular socket outlet and one 15/16 amps modular switch, connection

etc. as required. (For power plugs to be used in General purpose).

8 2.18 Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole Each 1.00 1,621.00 1,723.61 1,723.61

and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet

steel enclosure, on surface or in recess, with chained metal cover for the socket

out let and complete with connections, testing and commissioning etc. as

9 MR Supply and fixing of 32 Amps industrial socket points as directed including Nos. 1.00 8,848.00 8,848.00

providing 32 A socket angled outlet and 32 amps interlocking socket with 32

amps "D" curve DP MCB 5 sided PSP thermoplastic for housing and L6-30 type

connector socket and MCB and earthing complete with connections, testing

and commissioning etc. as required.

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

10 MR Fabricating supplying installation on surface/cable tray 2.0 mm thick factory

fabricated GI Sheet raceways height 40 mm and of totally enclosed with 3mm

thick covered with screw. Two lengths of channel / channel and junction box

shall be joined together to make it dust and water proof. Chipping and removing

screed to install the raceways in floor, including removal and disposing of debris

as per PMC instructions, finishing with PCC, providing chicken mesh and making

good as per Engineer in charge

f 50 mm (wide) x 40 mm (height) RM 9.00 912.00 8,208.00

11 4.5 Supplying and installing following size of perforated painted with powder coating

M.S. cable trays Reducer with perforation not more than 17.5%, joined with

connectors, suspended from the ceiling with M.S. suspenders including bolts &

nuts, painting suspenders etc as required.

a 4.5.10 450 mm width X 62.5 mm depth X 2.0 mm thickness RM 2.00 2,966.00 3,153.75 6,307.50

b 4.5.4 300 mm width X 50 mm depth X 1.6 mm thickness RM 2.00 1,718.00 1,826.75 3,653.50

c 4.5.2 150 mm width X 50 mm depth X 1.6 mm thickness RM 5.00 1,186.00 1,261.07 6,305.37

12 MR Fabrication. Supplying, installation, fixing in position GI Junction Boxes 2 mm thick

complete with 3 mm thick GI Covers with screw duly providing rubber gaskets

between the cover and the Junction Box, screws etc. as required complete.

a 500 x 500 x 50 mm MS junction box. Nos. 1.00 1,731.00 1,731.00

b 350 x 350 x 50 mm MS junction box. Nos. 1.00 1,344.00 1,344.00

c 300 x 300 x 50 mm MS junction box. Nos. 3.00 1,157.00 3,471.00

d 200 x 200 x 50 mm MS junction box. Nos. 3.00 1,078.00 3,234.00

e 150 x 150 x 50 mm MS junction box. Nos. 3.00 912.00 2,736.00

f 100 x 100 x 50 mm MS junction box. Nos. 2.00 746.00 1,492.00

13 1.17 Supplying and drawing following sizes of FRLS PVC insulated copper conductor,

single core cable in the existing surface/ recessed steel/ PVC conduit as

14 MR Providing and fixing on work station/ partition of 3 Nos.6/13 amp flush type 3 pin Nos. 19.00 912.00 17,328.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for for housing switches and sockets and earthing complete as

required ( for ups power point)

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

15 MR Providing and fixing on work station/ partition of 2 Nos.6/13 amp flush type 3 pin Nos. 5.00 828.00 4,140.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( For ups power points.)

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

16 MR Providing and fixing on work station/ partition of 1 No.6/13 amp flush type 3 pin Nos. 1.00 717.00 717.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( for ups power points.)

17 MR Providing and fixing on work station/ partition of 2 Nos.6/13 amp flush type 3 pin Nos. 2.00 828.00 1,656.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( For raw power points.)

18 MR Providing and fixing on work station/ partition of 1 No.6/13 amp flush type 3 pin Nos. 19.00 717.00 13,623.00

international socket and 1 No. 16 amps switch, cover plate in existing flap box/

raceways/GI box for housing switches and sockets and earthing complete as

required ( for raw power points.)

19 1.21 Supplying and fixing of following sizes of pvc conduit medium along with

accessories in surface/recess including cutting the wall and making good the

same in case of recessed conduit as required.

20 ` Providing and fixing in position the following pvc flexible conduits including all

fixing accessories as required.

a 20 mm dia flexible conduit with end couplers RM 5.00 48.00 240.00

b 25 mm dia flexible conduit with end couplers RM 8.00 62.00 496.00

c 32 mm dia flexible conduit with end couplers RM 2.00 90.00 180.00

21 MR Supply, installation, testing and commissioning of the following sizes of PVC

trunking system with end caps, bends, elbows complete as required.

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

1 MR Providing and fixing of Gel-Chemical Earthing Electrode of G.I. made as pipe in Each 1.00 84,336.00 84,336.00

pipe technology(IS:3043 : 1987)duly CPRI Approved as per following

Length - (3000 mm)

DIA (outer) - (80 mm)

DIA (Inner) - (40 mm)

DIA-Terminal Strip Hole - (25 mm)

Space Inside Electrodes - (Filled with Conductive Mixture)

Hot Dip Galvanizing - (70 - 100 Microns)

And earth enhancing compound should be used to treat the soil for lowering the

effective ground impedance 50Kg for each earth pit to make it maintenance

free and to minimize the ground voltage potential rise and pit covered with PVC

2 5.4 Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including Each 1.00 7,472.00 7,944.98 7,944.98

accessories, and providing masonry enclosure with cover plate having locking

arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and

salt as required.

3 5.10 Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe from Metre 17.00 1,551.00 1,649.18 28,036.03

earth electrode including connection with brass nut bolt, spring, washer

excavation and re-filling etc. as required.

4 5.11 Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth Metre 17.00 706.00 750.69 12,761.73

electrode including connection with G.I. nut, bolt, spring, washer excavation and

re-filling etc. as required.

5 5.14 Providing and fixing 25 mm X 5 mm copper strip on surface or in recess with all Metre 26.00 1,162.00 1,235.55 32,124.42

accessories for connections etc. as required.

6 5.15 Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess with all Metre 34.00 244.00 259.45 8,821.14

accessories for connections etc. as required.

7 MR Supplying ,laying, and making proper connections, end terminations, testing & 0.00

commissioning of the following sizes of 1.1 KV unarmoured PVC insulated

copper conducter cables heavy duty flexible cable (wires) in existing RCC

ducts/ laid in ground /laid on Cable Trays including clamping the cables to

supports in an approved manner as required complete with all accessories.

a 1 x 50 sq. mm PVC insulated copper conductor flexible cable (Green colour for RM 22.00 1,072.00 23,584.00

b 1 x 25 sq. mm PVC insulated copper conductor flexible cable (wire) (Green RM 5.00 567.00 2,835.00

colour for UPS SDB Earthing)

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

c 1 x 16 Sq. mm PVC insulated copper conductor wire (Green Colour for UPS DB RM 5.00 465.00 2,325.00

Sub-main Earthing)

d 1 x 10 Sq. mm PVC insulated copper conductor wire (Green Colour for UPS HUB RM 17.00 281.00 4,777.00

DB Sub-main Earthing)

e 1 Nos x 6 Sq. mm PVC insulated copper conductor wire.(Green Colour for false RM 17.00 129.00 2,193.00

flooring earthing)

f 1 x 4 Sq. mm PVC insulated copper conductor wire (Green Colour) for server RM 17.00 89.00 1,513.00

8 MR Supply, installation, testing and commissioning of copper Earth Set 1.00 7,323.00 7,323.00

busbar(50X5X400)mm in MS sheet enclosure complete as required.

C SUPPLY & FIXING OF LIGHTING FIXTURES

1 Supply, installation, testing and commissioning of the the following Lighting

fixtures including all internal connection wires, electronic ballast, lamps,

mounting arrangement, suspensions and all necessary items required to install

the light fixtures at site. Rate shall include all taxes and duties, transportation

a MR 1x12 Watt Circular Down LED Light Fixture suitable for grid tile ceiling 600x600 grid Nos 1.00 2,216.00 2,216.00

with electronic ballast, mounts to support the ballast or with integral ballast,

suitable lengths of prewired connection between ballast and light fixture,

diffuser, suitable mounts, suspension cables complete as required.

b MR LED cove light fixture with average lumen output of 630 lm per metre for white RM 32.00 1,177.00 37,664.00

color including all drivers, connecting cables, controllers, led mounted in

extruded poly corbonate, suitable to end to end coupling, non dimmable,

average 4 watt / metre for mono color and 11 watt/ metre for white color. Color

as per PMC instruction complete as required.

c MR Recessed mounted 36W LED light fixture suitable for mounting in 300x1200 grid Nos. 11.00 11,415.00 125,565.00

ceiling with acrylic duffuser with 100% uniform illumination, intergral driver, internal

wiring, supports, accessories for mounting, lamps complete.

d MR COV LED disk round 9 w light ceiling fitting complete with all required No. 35.00 1,177.00 41,195.00

accessories including connection and lamp .

e MR Recess mounting Linear LED luminarie with energy efficient high efficency No's 5.00 9,586.00 47,930.00

translucence PMMA diffuser, LED electronic driver and other accessories pre

wired up to terminal block, 1200 mm (NS) long with CRCA sheet housing, 31 -36

watt, Luminous efficiency of luminair >80 lm /w. CCT 6000 (+/_500) K , Color

Rendering Index (CRI) > 80 , service life 50,000 hrs at 25 deg,C.

f MR Supply, Installation, testing and Commisioning of decorative chandlier light No's 0.00 49,626.00 0.00

fixture, consisting of LED lights, drivers, etc. inclusing all accessories, supports from

true RCC Slab complete with all respects. (Base Rate Rs.35000/-)

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

g MR Supply, Installation, Testing & Commissioning of LED ring pendant shape indoor Nos 1.00 24,813.00 24,813.00

surface office panel suitable for general lighting. Luminaire should have CRCA

body in white color . The luminaire should have CRI > 80 and CCT of 4000K. The

luminaire shall be compliant with IP20 classification.The fixture should have a

minimum system efficacy of 80 lumen/Watt and a minimum system lumen

output of 3300 lumens and maximum system wattage 43Watts. The luminaire

shall be designed so as to ensure lumen depreciation of up to 30% over 50k

burning hours @ design ambient temp 45 deg C. The electronic driver used shall

have a power factor >0.90 . Similar to image shown below with all necessary ms

conduit , wiring switch socket to control light fixture complete.Size 1200mm Dia.

D OCCUPANCY SENSORS 0.00

1 MR Supply, fixing testing and commissioning of occupancy sensors with day light Nos. 3.00 5,887.00 17,661.00

sensor with all necessary wiring to be integrated for lighting control complete with

following specification.

PIR Motion Sensors will itself recover its cost by reducing your electricity bills and

will further save your electricity cost for the future. Very easy installation and can

be installed by technician itself. No separate wiring is required hence no

additional installation cost. No modification is required and complies with current

aesthetics. Pay back within ten months according toresidential meter and six

months according to construction meter. Ingress Protection: IP20 as required as

per clients requirement.

E Automation Dali Light 0.00

1 MR Recess mounting Linear With Dali dimmable driver LED luminarie with energy No's 3.00 12,052.00 36,156.00

efficient high efficency translucence PMMA diffuser, LED electronic driver and

other accessories pre wired up to terminal block, 1200 mm (NS) long with CRCA

sheet housing, 31 -36 watt, Luminous efficiency of luminair >80 lm /w. CCT 6000

(+/_500) K , Color Rendering Index (CRI) > 80 , service life 50,000 hrs at 25 deg,C.

2 MR Supply, Installtion, Testing & Commissioning of Recess Mounted circular 15W LED Nos. 4.00 14,808.00 59,232.00

downlighter with pressure diecast aluminimum housing, high efficiency PMMA

diffuser complete with electronic LED driver, PF>0.9, THD<10%, rated life of L-70 @

30,000 hours having minimum lumens output of 2100 lumens and efficacy better

than 80 lumens / watt with CRI> 80 including fixing in false ceiling & connection

with 3x1.5 Sq.mm. PVC insulated FRLS copper conductor cable in flexible

metalic conduit etc. as required. With Dali dimmable driver.

3 MR Supply, Installation Testing & Commissioning of DIN - rail mounted Dali dimming No's 1.00 157,386.00 157,386.00

controller with two (2) independent Dali buses with upto 64 ballasts per bus, 4

groups of sensor input, i/c power supply at 220-240V, 50 Hz. i/c connections etc

4 MR Supply, Installation Testing & Commissioning of DIN - rail mounted ON/OFF No's 1.00 110,596.00 110,596.00

switching controller with 4 switched outputs having max load limit of 10 Amp per

output, includes communication link to any device and 2 group of sensor inputs,

i/c power supply at 230V, 50Hz.i/c connections etc as reqd.

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

5 MR Supply, Installation Testing & Commissioning of 8 button wired keypad with No's 1.00 83,949.00 83,949.00

infrared receiver complete with mounting back box 75mm (W) X 75mm (H) X

35mm (D), engraving codes with front plate in arctic white finish, 8 scene wireless

remote control including batteries complete as required.

1 MR Supply, laying and testing of under noted sizes of Aluminium conductor XLPE

insulated PVC sheathed & sleeved FRLS armoured and overall PVC sleeved 1.1

KV grade power distribution cables conforming to relevant IS code 7098 and as

per specification in ground or in existing trenches/ through pipe/ on wall / on

cable trays including dressing and clamping the cable with MS clamps etc. as

2 9.1 Supplying and making end termination with brass compression gland and

aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

3 MR Supply fixing and making proper end termination with sutable accessories of

under noted sizes of copper conductor PVC insulated PVC sleeved 1.1 KV grade

power distribution flexible cable/wires heavy duty conforming to relevant IS

code and as per specification in ground or in existing trenches/ through pipe/ on

wall / on cable trays including dressing and clamping the cable as required.

a 1 x 50 sq.mm PVC insulated flexible copper conductor cables RM 11.00 1,080.00 11,880.00

b 1 x 25 sq.mm PVC insulated flexible copper conductor cables RM 15.00 637.00 9,555.00

c 1 x 16 sq.mm PVC insulated flexible copper conductor cables RM 22.00 526.00 11,572.00

d 1 x 10 sq.mm PVC insulated flexible copper conductor cables RM 22.00 413.00 9,086.00

e 1 x 6 sq.mm PVC insulated flexible copper conductor cables RM 52.00 360.00 18,720.00

f 1 x 4 sq.mm PVC insulated flexible copper conductor cables RM 53.00 194.00 10,282.00

4 MR Supply and fixing of ms angle/chanel support or frame work in position including Kg. 43.00 194.00 8,342.00

clamps,with fabrication work including cutting, bending, welding, drilling bolting

etc. as per design as required. One coat of primer and 2 coats of enamel paint

of approved shade shall be provided.

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

5 MR Supplying and fixing of following size of perforated G I cable trays with

perforation not more than 17.5%, in convenient sections, joined with connectors,

suspended from the ceiling with G I. suspenders including bolts & nuts, etc as

a 450 mm width X 50 mm depth X 2.0 mm thickness RM 15.00 2,036.00 30,540.00

b 300 mm width X 50 mm depth X 1.6 mm thickness RM 31.00 1,594.00 49,414.00

c 150 mm width X 50 mm depth X 1.6 mm thickness RM 21.00 1,095.00 22,995.00

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

G L.T PANELS/ DISTRIBUTION BOARDS

MR Supply, installation, testing and commissioning of indoor floor mounted/ wall

mounted, IP42, factory built, modular, sectionalised, compartmentalized,

extendable type LT cubicle panel of suitable size suitable for operation on

433/415 volts, 50 Hz AC 3 phase 4 wire supply system fabricated from CRCA

sheet steel of 2mm thick for frame work and covers, 3mm thick for gland plates

with stiffeners wherever required, having vibration free structure chemically

treated with seven tank process or better before painting for surface treatment

and powder coated in approved shade, with suitable electrolytic grade high

conductivity bus bars extensible, DMC/ SMC (whichever is superior) bus bar

supports, with short circuit withstand capacity as mentioned ,bottom base

channel of section not less than 100mmX 50mmX 5 mm thick, fabrication shall be

done in transportable sections, entire panel shall have a common earth bar of

required size at the rear with 2 Nos. earth stud, connections and interconnection

with solid conductor wires / copper strips, neutral links, control wiring with 1.5

sqmm. & 2.5sqmm. PVC insulated FRLS copper conductor S/C cable for voltage

& current respectively, including providing and fixing following switch gears and

as per schedules ,technical specifications etc.complete as required.

1 Electrical Panel-1 Nos 0.00 269,399.00 0.00

Surge arrester (1 No.)

2kVp,50kA rated surge arrestor suitable fo both lightning and switching 0.00

surges,complete with suitable protection fuse (inbuilt).

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated thermal magnetic based MCCB with

inbuilt LSIG protection - 1 Nos.

Metering (1 No.)

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line and

phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 1

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on, off,

415V ,160/5A, 10VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in rectangular

cross section and suitable for 415V, FP, 50 Hz, 200 A, 25 kA for 1 sec of required

length and cross sectional area.

2 Nos. 415V, 50Hz, 100A, 4P, 25kA for 1 sec rated Thermal magnetic based

7 Nos. 415V, 50Hz, 40A, 4P, 10 kA MCB.

4 Nos. 415V, 50Hz, 63A, 4P, 10 kA MCB.

Indication lamps

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 2

2 UPS Output Panel

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated thermal magnetic based MCCB with

inbuilt LSIG protection - 2 Nos.

Metering (2 No.)

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line and

phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) - 2

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on, off,

2 Nos.-415V ,160/5A, 10VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in rectangular

cross section and suitable for 415V, FP, 50 Hz,300 A, 25 kA for 1 sec of required

length and cross sectional area.

2 Nos. 415V, 50Hz, 40A, 4P, 10 kA MCB.

3 Nos. 415V, 50Hz, 63A, 4P, 10 kA MCB.

3 Light & Power Distribution Board

a MR Supply and installation of sheet metal enclosed double door 48modules TPN DB, Nos. 1.00 40,384.00 40,384.00

each phase consisting of 8 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

b MR Supply and installation of sheet metal enclosed double door 56modules TPN DB, Nos. 1.00 43,701.00 43,701.00

each phase consisting of 10 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

4 UPS Distribution Boards

Digitally signed by AMIT

S.NO DSR 2022 Ref. DESCRIPTION OF ITEM UNIT BOQ QTY DSR RATE DSR Rate after NDSR Rate DSR AMOUNT NDSR Amount

No. (A). (B) GST (D) (C*A) (D*A)

a MR Supply and installation of sheet metal enclosed double door 56modules TPN DB, Nos. 1.00 43,701.00 43,701.00

each phase consisting of 12 Nos. 10/20 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A TPN MCB as incomer. all mcb's shall be

b MR Supply and installation of sheet metal enclosed double door 48modules TPN DB,, Nos. 1.00 40,384.00 40,384.00

each phase consisting of 10 Nos. 32/16 AMP SP MCB’s and each phase

controlled by one number 100 mA sensitivity 63 AMPS DP RCCB backed up with

63 Amps DP MCB and one number 63 A 4P MCB as incomer. (For UPS Power)

all mcb's shall be D-curve.

H MR Supply, installation of 1.1KV grade rubber mat 900mm wide in electrical rooms. RM 1.00 3,316.00 3,316.00

I MR Supply & Fixing of danger notice board Nos. 1.00 2,488.00 2,488.00

J MR Supply of First aid box Nos. 0.00 829.00 0.00

K MR Supply & Fixing shock treatment chart Nos. 1.00 2,488.00 2,488.00

TOTAL ELECTRICAL WORK AMOUNT 802,453.30 1,563,055.00

Digitally signed by AMIT

S.H. 3 FIRE DETECTION & ALARM SYSTEM WORK : CAQM , NEW DELHI ESTIMATE

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE NDSR AMOUNT

1 FIRE DETECTION & ALARM SYSTEM

1.1 Dismantling of existing fire alarm detectors complete as required Nos 2 702.00 1404.00

1.2 Dismantling of existing fire alarm cable complete as required Mtrs 5 35 175.00

1.3 Resinstallation and reconfiguration of existing fire alarm detectors as per site Nos 2 1002 2004.00

requirement complete as required

1.4 Laying of existing fire alarm cable as per site requirement complete as required Mtrs 17 64 1088.00

1.5 Supply, Installation, Testing, and commissioning of smoke detectors compatible Nos 13 4963 64519.00

with fire alarm system and as per site requirement complete as required

1.6 Supply, Installation, Testing, and commissioning of fault isolators compatible Nos 1 5530 5530.00

with fire alarm system and as per site requirement complete as required

complete as required

1.7 Supply, Installation, Testing, and commissioning of control/monitor module Nos 5530 0.00

compatible with existing fire alarm system and as per site requirement

complete as required complete as required

1.8 Supplying, installation, testing and commissioning of micro processor based

intelligent addressable main fire alarm panel, central processing unit with the

following loop modules and capable of supporting not less than 240 devices

(including detectors) and minimum 120 detectors per loop and loop length up

to 2 km, network communication card, minimum 320 character graphics/ LCD

display with touch screen or other keypad and minimum 4000 events history

log in the non volatile memory (EPROM), power supply unit (230± 5% V, 50 hz),

48 hrs back-up with 24 volt sealed maintenance free batteries with automatic

charger. The panel shall have facility to connect printer to printout log and

facility to have seamless integration with analog/digital voice evacuation

system (which is part of the schedule of work under SH: PA System) and shall

be complete with all accessories . The panel shall be compatible for IBMS

system with open protocol BACnet/ Modbus over IP complete as per

specifications.

Digitally signed by AMIT

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE NDSR AMOUNT

Note : Cost to inclusive of integration of fire alarm system with existing building

fire larm system.

2.1 Dismantling of existing speakers complete as required Nos 1 142 142.00

2.2 Dismantling of existing complete speaker cable as required Mtrs 5 35 175.00

2.3 Resinstallation and reconfiguration of existing speakers as per site requirement Nos 1 278 278.00

complete as required

2.4 Laying of speaker cable as per site requirement complete as required Mtrs 55 49 2695.00

2.5 Supply, Installation, Testing, and commissioning of 6watt ceiling speaker as per Nos 9 2127 19143.00

site requirement complete as required

2.6 Supply, Installation, Testing, and commissioning of 10 watt wall mount speaker Nos 1 5530 5530.00

as per site requirement complete as required

2.7 Supply, Installation, Testing, and commissioning of 500watt amplifier as per site Nos 176789.00 0.00

requirement complete as required complete as required

TOTAL FIRE DETECTION & ALARM WORK AMOUNT 102,683.00

Digitally signed by AMIT

S.H. 6 HVAC WORK : CAQM , NEW DELHI ESTIMATE

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

1.a VRF/VRV OUTDOOR UNIT

Supply, Installation, Testing & Commissioning of Modular type Variable

Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units

suitable for cooling/heating having 100% hermetically sealed inverter type

twin Rotary/Scroll Compressor(s),minimum two compressors (with

individual separate PCB) for above 14HP modules, microprocessor based

Controller, top discharge type condensing unit(s), with R-410-A Refrigerant

or equivalent, vibration Isolators with suitable foundation etc. complete as

required. To have better efficiency condenser fan shall be capable to operate

at different speed with respect to load. The unit shall deliver the rated

capacity and in confirmation as per IS 18728:2024 and CPWD

Specifications and work even at 50°C ambient temperature without tripping.

The system shall be able to deliver 100% of the rated capacity upto 39

Degree Celcius.The unit shall be suitable to work on 400V +/- 10%, 3 Phase,

7.3 50Hz AC power supply and BMS compatible. The unit shall be filled with first

charge of the refrigerant and ready for use as required. The condenser

should be coated with a hydrophilic film to prevent water accumulation on

surface of the heat exchanger, enhance water dispersion, and reduce the

risk of degradation, thereby improving overall performance and durability.

The Indian Seasonal Energy Efficiency Ratio (ISEER) of the unit shall be as

per Energy Conservation and Sustainable Building Code (ECSBC) 2024 as

below and complete as per CPWD specification, connections, inter

connections etc. as required. (For capacity <40 kWr ISEER 7.4, Capacity >

40 and <70 ISEER 7.5, Capacity > 70 ISEER 7.6 for Super ECSBC

Supply, Installation, Testing and Commissioning of following minimum

capacity 4 way Cassette Type Indoor ceiling mounted unit equipped with

synthetic washable media pre-filter, fan section with low noise fan /

dynamically balanced blower, multispeed motor, coil section with DX Copper

coil, electronic expansion valve, outer cabinet, drain pump, grill, necessary

supports, vibration Isolation, Corded remote control etc., suitable for

1.b 7.4 operation on single phase 230 V ± 10%, 50Hz AC supply, complete, as

required. The Indoor units must shut down upon receiving a singal from the

BMS System/Fire Signals. The system shall be capable to adjust air flow as

per room requirement in auto mode. The cooling capacity of indoor unit will

be at air inlet conditions of 27 Degree C DB and 19 Degree C WB

temperature. (Make will be same as of Outdoor)

4-Way Cassette type

HI - WALLSPLIT SYSTEMS

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Supply , Installation, Testing and Commissioning of Air Cooled Hi Wall split type

Air conditioners complete with Indoor unit(IDU), Out door unit (ODU), surface /

concealed copper Refrigerant piping with insulation (closed cell elastomeric

nitrile rubber tubular pipe section) upto 3 Mtr (IDU to ODU), copper power

cable upto 3.5 Mtr (IDU to ODU) i/c drain pipe R-32/R-410/ R407 Green

Refrigerant, wireless Remote control, suitable for working between 180-260V

with low & high voltage cutoff and 50 hz ,1 phase AC supply capable of

performing cooling, dehumidification, air circulation of following capacity

with Scroll / rotary compressor. The system shall be able to deliver 100% of the

rated capacity upto 42 Degree Celsius. Min 5 year Original Equipment

Manufacturer (OEM) warranty both compressor and Printed Circuit Board

(PCB). Must comply : Electrical cable IS 694 or IS 9968 temperature sensing

control IS /International Electro technical Commission (IEC) 60730, hermetic

compressor IS 10617, heat exchanger IS 11329, capacitor IS 2993 and motor IS

12615. Complete as per CPWD specification and IS : 1391 Part II 2023. The

system shall be able to operate up to 50 0C (out door ambient temperature).

1.b.2 8.2.3 1.5 TR with 5 Star BEE Rating Nos 1 42055 42055

1.b.3 MR Corded Remote controls Nos 0 4781 0

1.b.4 MR Communication cable (1.5 sqmm X 2 Core) Rmt 4 385 1540

Supply, installation, testing and commissioning of MS fabricated outdoor unit

stand for placing outdoor unit of VRV system. The stand shall be

manufactured from MS C channel of minimum 3-4 mm thick. It shall be

finished with enamel paint as per client/architect approval.

2.0 REFRIGERANT PIPING

Supply, Installation, testing and commissioning including vaccumiazation

and Nitrogen testing of following nominal sizes of soft/hard drawn copper

refrigerant piping for VRV/VRF system, complete with fittings, with suitable

adjustable ring type hanger supports, jointing/brazing including accessories,

insulated with XPLE Class-O tubular insulation/with Class-O closed cell

VRF/VRV elastometric nitrile rubber tubular sleeves sections of 19 mm thick insulation

as given below for Suction and Liquid lines, all accessories as per

specifications etc. as required :

2.1 7.14.3 12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 21 487.0 10227

2.2 7.14.4 15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm Rmt 21 615.0 12915

2.3 7.14.5 19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm Rmt 21 739.0 15519

CABLE TRAY FOR REFRIGERANT PIPING

Supplying and installing of following size of perforated hot dip galvanized G.I

cable tray with perforations not more than 17.5%, in convenient sections,

joined with connectors, suspended from ceiling with G.I suspenders including

bolts and nuts, etc. for carrying refrigerant pipe in outdoor application as

3.1. 450 mm width x 62.5 mm depth x 2 mm thickness Rmt 2 1,325 2650

3.2 225mm width x 50 mm depth x 1.6 mm thickness Rmt 8 962 7696

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

4.0 CONDENSATE DRAIN UPVC PIPE

Supply, installation, testing and commissioning of uPVC Pipe ,complete with

fittings, supports,U trap arrangement,Clean Plug with 6mm nitrile insulation

and accessories as per specifications, drawings.

B CHAPTER-2: FRESH AIR DEMAND CONTROLLED ENHANCED VENTILATION

5.0 ZONE REGULATION DEVICE/VAV BOXES

Supplying, Installing, testing and commissioning of Pressure independent VAV

for climate control with multi-hop wireless mesh module, made out of heavy

gauge extruded alluminium of 1.5 mm nominal thickness consists of low

leakage extruded alluminium volume control damper with additional

acoustic cladding; Rapid Average Pitot tube; Air Flow Straightner (Honey-

Comb patterned); slab/duct temperature sensor or optional thumbwheel

setpoint adjustment. Dynamic factory calibrated and adjustable flow range

of different capacities.

Note : Shall be ordered in site specific duct size without transition pieces and

no reduction in area for airflow measurement. VAV's shall be certified in

accordance with AMCA 611/511 for airflow measurement and leakage (Class

1.VAVs shall be pressure independent type & low velocity type

2.VAV Boxes shall be slow reacting type capable of delivering variable air

volume type by the action of opposed blade volume control damper

3.VAV boxes shall be supplied with end flanges for attachment to flanged

duct ends and shall be complete with all internal Acoustic treatment.

4.The casing shall be double skin type of Galvanized sheet steel construction

with a completely sealed, easily removable. The access shall be provided per

OEM and suitable to site.

5.VAV shall be electronically controlled networkable controller type

complete with low leakage damper, actuator , Microprocessor unit , wall/

ceiling mounted temperature sensor with ON/OFF Switch , control transformer

, unit hander brackets etc.

6.VAV Boxes shall also be able to reset any air flow between zero and the

maximum air quantity that the boxes can handle without changing orifices or

other parts, but the boxes shall be factory set at 10% of the maximum flow as

7.The noise level from the VAV boxes shall not exceed 35 dbA

8.The temperature sensor and the entire control mechanism shall be fully

compatible with BMS System. Datas like temperatures, set points , damper

position shall be monitored through BMS system

9.Integrators for the below VAVs to connect with the BMS system to read and

modify the parameters. Integrator should release open protocol BACnet /

MODBUS to integrate with third party BMS System. The integrator shall be

approved through engineer in charge / consultant before procuring the VAVs.

11.Power wiring from the Socket to VAVs

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

The VAV shall be installed on the exisiting ductwork and the cost shall include

cutting of existing ductwork, fixing new pieces as required and rebalancing of

AHU to meet the requirement. No Extra cost shall be given

MR Pressure Independent zone regulation device on Existing Grilles/Diffusers

Supplying, Installing, testing and commissioning of Pressure independent zone

regulation device to maintain desired minimum or maximum flow rate at

rectangular supply air outlet without plenum box. Having Low leak extruded

airfoil multi-blade opposed blade damper for grilles/diffuser, area under

given size.. Made out of heavy gauge extruded aluminium airfoil blades and

hat type 65 mm deep frame, complete with exposed gear drive, EPDM blade

seal, and wire-free mesh networked zone control and actuator. The zone

regulators shall be installed in the collars of the diffusers, grilles per drawings.

6.0 Room Thermostats

Supplying, Installing, testing and commissioning of Room thermostats having

MR temperature, & humidity sensor; capacitive touch button with e-ink display; No. 3 5,041 15123

3.3V power supply and wire-free mesh control link.

C CHAPTER-3: AIR DISTRIBUTION SYSTEM

7.0. DSR 2019 GSS DUCT (Factory Fabricated Duct)

Supply, installation, balancing and commissioning of factory fabricated GSS

sheet metal rectangular/round ducting complete with neoprene rubber

16.12.1 gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per

approved drawings and specifications of following sheet thickness complete

GSS DUCT (Site Fabricated Duct)

Supply, installation, balancing and commissioning of fabricated at site GSS

sheet metal rectangular/round ducting complete with neoprene rubber

8.0 16.12.2 gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per

approved drawings and specifications of following sheet thickness complete

9.0 DSR 2019 Supply Air Grilles

Supplying & fixing of powder coated extruded aluminium Supply Air Grilles 9,016.78 45,083.92

16.15 with Aluminium volume control dampers of various sizes and as per Sqmt 5 8,480

specifications and approved drawings and schedules.

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

10.0 DSR 2019 Return Air Grilles

Supplying & fixing of powder coated extruded aluminium Return Air Grilles 5,855.59 23,422.37

16.16 with louvers but without volume control dampers of various sizes and as per Sqmt 4 5,507

specifications and approved drawings and schedules.

11.0 EXHAUST/FRESH AIR LOUVERS

Supplying, Installing, testing and commissioning of powder coated extruded

aluminium exhaust air louvers with min.60 % free area, with metallic frame

work & fixing accessories, to be fixed on external wall to exhaust air from

basement area to ambient , it shall be suitable for exhausting required air in

CFM . Louvers need to be suitable in order avoid rain water entry in to

basement @ 15 degree deflection with bird screen complete as per

specification approved drawings and schedules.

12.0 DSR 2019 Supply Air Diffusers

Supply , installation , testing and commissioning of supply air diffusers of 12,082.28 36,246.83

Powder coated Aluminium with Aluminium volume control dampers with anti

smudge ring and removable core. Diffusers shall be as per specification &

16.17 the sizes will be as per drawings and schedules :

13.0 Return Air Diffusers

Supply , installation , testing and commissioning of return air diffusers of 8,037.48 24,112.45

Powder coated Aluminium without volume control dampers with anti

smudge ring and removable core. Diffusers shall be as per specification &

16.18 the sizes will be as per drawings and schedules :

14.0 COLLAR DAMPER

Supplying, installing, testing & commissioning of GI collar damper with

minimum 1.6 mm flange and 1.8 mm blade thickness within ducts to be

provided with suitable links, levers and quadrants for manual control of

volume of air flow and for proper balancing of the air distribution system as

per schedules & drawings.

15.0 DSR 2019 Motorised Volume Control Damper

Supply, installation, testing and commissioning of motorised(ON/OFF Type)

duct mounted opposed blade G.I volume control damper with enthalpy

16.14 sensor and necessary control wiring (minimum 1.5 sqmm ) for integeration

within IDU room.The unit shall provided as shown in the drawings. The unit shall

be capable to communicate with BMS system.

16.0 DSR 2019 Fire Damper

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Supplying, Fixing,testing and commissioning of fire damper in supply air

duct/main branch and return air path as and where required of required sizes

i/c control wiring, the damper shall be motorized and spring return so as to

close the damper in the event of power failure automatically and open the

same in case of power being restored. The spring return action shall be inbuilt

mechanism and not externally mounted. the damper shall also be closed in

the event of fire signal complete as required and as per specifications.

16.2 16.20.2 Actuator (Rated torque-10 N.m/m2) Each 1 9212 9,795.12 9,795.12

17.0 Back Draft Damper/Gravity Damper

Supplying, Fixing,testing and commissioning of Extruded aluminum of

Minimum 0.050 inch (1.2 mm) thick backdraft damper with extruded

aluminum blades suitable for application in HVAC systems with velocities to

MR 1,500 feet per minute (305 m/min). The damper shall withstand -10 to 60 Sqmt 1.0 6537 6537

degree celsius temperature. Maximum back pressure of 6" w.g., Minimum air

velocity of 1500 fpm.The damper shall be complete as required and as per

specifications.

D CHAPTER 4: INSULATION & ACOUSTIC

18.0 DUCT INSULATION

Supply and installation of cross linked closed cell Oxide Acetate Foam

Thermal insulation on ducts having density 0f 30 to 33 Kg/ M³ ,having K value

0.029 W/m ° K at 40°C Deg temp and temp range of -70°C to +100°C and fire

MR rating Class O as per BS 476 Part 6 from CBRI,Roorkee as per the approved

specifications. Smoke & Toxicity index of material shall be passed as per IMO

MSC 307 ( 88 ) 2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US

13mm thick insulation oxide acetate foam laminated with aluminium foil for

supply air duct

9 mm thick insulation oxide acetate foam laminated with aluminium foil for

Return air duct

19.0 MR DUCT ACOUSTIC LINING

Supply and installation of cross linked open cell acco isolate acoustic

insulation for duct having density of 30 to 55 Kg/ M³ ,having K value 0.029

W/m ° K at 40°C Deg temp and temp range of -70°C to +100°C and fire

rating Class O as per BS 476 Part 6 from CBRI,Roorkee as per the approved

specifications. Smoke & Toxicity index of material shall be passed as per IMO

MSC 307 ( 88 ) 2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US

19.1 25mm thickacco isolate acoustic open cell insulation Sqmt 5 905 4525

20.0 MR AHU ROOM ACOUSTIC LINING

Supply and installation of cross linked open cell acco isolate acoustic

insulation for AHU room having density of 30 to 55 Kg/ M³ ,having K value

0.029 W/m ° K at 40°C Deg temp and temp range of -70°C to +100°C and fire

rating Class O as per BS 476 Part 6 from CBRI,Roorkee as per the approved

specifications. Smoke & Toxicity index of material shall be passed as per IMO

MSC 307 ( 88 ) 2010 Anexx 1 Pt 2.• Material shall be CFC/ HCFC free as per US

25mm thickacco isolate acoustic open cell insulation for Ahu acoustic

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

21.0 MR DOUBLE LAYER CANVAS CONNECTION

Supply,Installation,testing and commissioning of double Layer canvas

connection fire retardant cloth for the end connection of Ductable

Units/AHUs and Ventilation fan to reduce the vibration.It shall be fire rated for

atleat 2 hrs. Refer tender specification for detail description

E CHAPTER 5: VENTILATION SYSTEM

22.0 INLINE FANS

Supply , installation , testing and commissoning , of duct mounted inline fans

complete with direct driven centrifugal fan , TEFC squirrel cage induction

motor , with efficiency class IE-3 whichever is higher , direct drive

22.1 MR arrangement , heavy gauge sheet metal casing , rubber isolator mounts and

other accessories.The fan shall be complete in all respect and should match

the specification ,Drawings and Schedule. Inline fans shall be of following

22.2 1100 CFM (15 mm Static Pressure) Nos. 1 20887 20887

23.0 MR CEILING MOUNTED EXHAUST FANS

Supply , installation , testing and commissoning , of ceiling mounted inline

fans complete with direct driven centrifugal fan , direct drive arrangement ,

heavy gauge sheet metal casing , rubber isolator mounts and other

accessories.The fan shall be complete in all respect and should match the

specification ,Drawings and Schedule. Inline fans shall be of following

F CHAPTER-6: DEMOLISHING AND TAB WORK

SHEET METAL WORK

Demolishing of existing ductwork of all sizes, Insulation, Diffusers, Grilles,

dampers in complete respect and clean the ceiling for new ductwork as per

the new RCPs, Zones, Spaces marked in the drawings. The contractor to

examine and ensure no damage to other services like electrcial, lighting

fixtures, smoke detectors, structure etc running in the ceiling shall be made.

The contractor shall be responsible to clean and shift the uninstalled

ductwork and place it on the ground at the location suggest by

PMC/Engineer In Charge. NO extra cost shall be paid in any manner.

G CHAPTER-7: ELECTRICAL WORK

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Supply, installation, testing and commissioning of indoor/outdoor floor

mounted/ wall mounted, IP43/IP65, IS 61439 factory built, modular,

sectionalised, compartmentalized, extendable type LT cubicle panel of

suitable size suitable for operation on 433/415 volts, 50 Hz AC 3 phase 4 wire

supply system fabricated from CRCA sheet steel of 2mm thick for frame work

and covers, 3mm thick for gland plates with stiffeners wherever required,

having vibration free structure chemically treated with seven tank process or

better before painting for surface treatment and powder coated in

approved shade, with suitable electrolytic grade high conductivity bus bars

extensible, DMC/ SMC (whichever is superior) bus bar supports, with short

circuit withstand capacity as mentioned ,bottom base channel of section not

less than 100mmX 50mmX 5 mm thick, fabrication shall be done in

transportable sections, entire panel shall have a common earth bar of

required size at the rear with 2 Nos. earth stud, connections and

interconnection with solid conductor wires / copper strips, neutral links,

control wiring with 1.5 sqmm. & 2.5sqmm. PVC insulated FRLS copper

conductor S/C cable for voltage & current respectively, including providing

and fixing following switch gears and as per schedules ,technical

specifications etc.complete as required.

25.1 MR HVAC Panel-01,02 each - 117245 0

415V, 50Hz, 160A, 4P, 25kA for 1 sec rated microprocessor based MCCB with

inbuilt LSIG protection - 1 Nos.

Metering (1 No.)

Multifunction meter with inbuilt selector switch for measurement of current,

voltage, power factor, KVA, kVAh, KVArh, KVAR, frequency, ,KWHr (both line

and phase) complete as per specifications

Indication lamps

LED type phase indication lamps suitable for 230V,50Hz AC (red, yellow, blue) -

LED type Indication lamps for breaker, suitable for 230V,50Hz AC supply (on,

off, trip) - 1 set

415V ,160/5A, 15VA, CL-1 current transformer for metering

Busbar (1 Set - 4P + E)

Busbar made up of electrolytic grade high conductivity aluminium in

rectangular cross section and suitable for 415V, FP, 50 Hz, 300 A, 25 kA for 1

sec of required length and cross sectional area.

5Nos. 415V, 50Hz,63A, 4P, 10 kA MCB.

Supply,installation,testing and commissioning of 63A 4P,Isolator , heavy duty

solid neutral link in a sheet steel enclosure with required arrangement for

incoming and outgoing cable complete as required.(Weather Proof)

Supply,installation,testing and commissioning of 40A 4P,Isolator , heavy duty

solid neutral link in a sheet steel enclosure with required arrangement for

incoming and outgoing cable complete as required.(Weather Proof)

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. 513.57 20,542.96

pipe from earth electrode including connection with G.I. nut,

26.1. 5.11 bolt, spring, washer excavation and re-filling etc. as required.Providing and Metre 40 483

fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as

Providing and laying earth connection from earth electrode with 6 SWG dia 199.90 1,599.20

G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection

with G.I. thimble excavation and re-filling as required.

LT CABLE AND TERMINATION

Supplying, unloading, storing , laying, testing and commissioning of following

sizes of 1.1 kV grade XLPE insulated, FRLS (Heavy duty) Aluminium/copper

conductor armoured/unarmored cables suitable for working voltage upto

and including 1100 Volts, laid and tied on existing overhead cable trays; or

buried underground or laid and tied over MS supports in masonry trenches

including providing MS supports and clamps for fixing to supports in an

approved manner, providing fire retardant sealant where required complete

as required and as per specifications. Circuit identification tag should be

attached with the concerned cable alongwith the test report of following

sizes of cable to be submitted by the contractor at the time of delivery of

material at site. (Cable length may increse as per existing panel location).

27.3 MR 4C X 6 Sqmm Metre 4 246 982

Supplying and making end termination with brass compression gland and

28.0 9.1 aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE

aluminium conductor cable of 1.1 KV grade as required.

28.3 MR 4C X 6 Sqmm Each 1 162 162

Supplying following 1.1kV grade, XLPE insulated, FRLS type control

cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,

29.0 outer sheath provided with FRLS insulation and with all components as

mentioned in BOQ, specifications and schedule, complete as required.

29.1 MR 2C X 1.5 sqmm copper conductor Metre 7 201 1,407

29.2 MR 2C X 2.5 sqmm copper conductor Metre 15 253 3,795

Supplying and making end termination with single compression brass gland

and lugs for following size of 1.1kV grade, XLPE insulated, FRLS type control

cables,suitable for 415V, 50Hz, AC system, with inner and outer PVC sheath,

outer sheath provided with FRLS insulation and with all components as

mentioned in BOQ, specifications and schedule, complete as required. The

cost shall include the cost of crimping and all tools and accessories required

to complete the job in full respect.

Note : Al lugs shall be used for Al cable and cu lugs shall be used for copper

30.1 MR 2C X 1.5 sqmm copper conductor Each 1 182 182

30.2 MR 2C X 2.5 sqmm copper conductor Each 1 199 199

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

CABLE MANAGEMENT

31.0 SOCKET OUTLET POINT WIRING

Wiring including termination for 6 amp socket outlet point with 3 x 2.5 sq. mm

PVC insulated FRLS copper conductor wires in concealed/exposed 1.6 mm

thick in MS conduits including providing 6 amp switch,3 pin 6A shuttered

socket,anodised MS box for housing switches sockets, approved White

Polycarbonate modular cover plate and earthing.

Wiring including termination for 16 amp power socket outlet points with 3 x 4

sq. mm PVC insulated FRLS copper conductor wires for the 16 amp socket

outlet with 3 x 4 sq. mm PVC insulated FRLS copper conductor wires for the

second outlet of 650/1100 Volts grade in concealed/exposed 1.6 mm thick in

31.2 MR MS conduits as called for including providing 16 amp flush type combined 6 Set 2 6,167 12,334

pin shuttered sockets and switches, anodised MS outlet boxes for 16 A 6 pin

sockets and switches,approved White Polycarbonate modular cover plate

H SMART COMPREHENSIVE AIR PURIFICATION SOLUTION

Electronic Air Cleaner For AHU/DUCTABLE

The EAC Shall be suitable to reduce harmful pollutants like particulate matter

(PMx), PM 2.5, allergens, smoke, bacteria, pathogens etc. based on below

principle technology viz; Impingement, Polarization and Agglomeration for

passive air purification. It should be a slim structured unit specifically designed

for integration in Return Air path of ceiling suspended indoor units and AHUs.

EAC shall be equivalent to Merv-14 or Higher efficiency for AHU and Ductable

Units with low pressure drop. It should have 3x working principles and it

should be aluminum based or powder coated steel casing and should be self-

contained. The EAC shall have UL certified core components. The Basic Media

of Electric Filter shall Carry Class 2 Fire Rating Listing by UL for filter Media Pad

Component. The units shall meet ANSI/ASHRAE 52.2/ISO16890 standards and

have valid test report to verify filtration efficiency. The Supplier shall carry

UL2998 certificate for testing against Zero Ozone Emission either as Whole

unit or included components. The filter shall be capable of effectively

reducing haze particles, smoke, mold spores, and airborne bacteria, and shall

be supported by test reports from NABL-accredited laboratories verifying its

performance. The Electronic Air Cleaner shall preferably be GreenPro certified

by CII–IGBC (Confederation of Indian Industry – Indian Green Building Council .

Floor Mounted AHU

Active Purification System (Bi-Polar Ionization) For AHU/DUCTABLE/VRF

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Supply, Installation, Testing and commissioning of Bipolar Ionisation System.

The Bipolar Ionization System must be a combination of Needle Point Model

for AHU (Needle Point should have Nitinol (nickel titanium) Needles and

Carbon Fiber Brush Model for Cassettes and HI Wall AC units. The System

should produce positive and negative ions for creating a Bio Climate rich in

ions and hence neutralizing harmful pollutants including pathogens, Volatile

Organic Compounds and Particulate Matter.

The Carbon Brush self-balancing ionizer should be installed at the fan inlet of

fan coil units, VRF cassettes, ductless splits , NeedlePoint Ionizer shall be

installed at AHU and Ductable HVAC System.

Product should have UL 867 and UL 2998 certification (for zero ozone

emission). The OEM shall have Efficacy test report on COVID from any

Internationally/Nationally recognised Laboratory. The technology shall also

have UL 2043 for Fire and Smoke safety certificate , ISO 16000 for safety

against any Organic Byproduct and CSA C22.2#187 , CARB certification.

Manufacturers shall provide Test report from Internationally/Nationally

recognized Lab for proven efficacy on below pathogens with minimum kill

rates for the following pathogens given the allotted time and in a space

a) SARS-CoV-2 (COVID-19) Human Strain

b) MS2 Bacteriophage (Surrogates COVID-19)

c) Omicron Variant of SARS-CoV-2

e) Total Bacterial Count Reduction rate of more than 90% from NABL

f) Yeas & Mold/Total fungal count Reduction rate of more than 90% from

NABL Accredited Lab

AHU/DUCTABLE/VRF

32.1.2 Cassette Unit : 1.3 TR to 3.2 TR Nos. 3 ₹ 20,000 ₹ 60,000

Indoor Air Quality Monitoring System-

Digitally signed by AMIT

DSR Rate after GST NDSR Rate

Sr.No DSR No. Description Unit Quantity DSR Rate Multiplication DSR Amount NDSR Amount

A CHAPTER-1: VARIABLE REFRIGERANT FLOW SYSTEM

Supply, Installation, Testing & commissioning of IAQ Monitor to remotely

measure the levels of PM 2.5, VOCs, CO2, Temperature, Humidity on a real

time basis. The IAQ Monitor shall be capable of getting connected with Wi-Fi.

The Monitor should be capable of sending the indoor air quality information

on display Screen / Mobile/Workstation as per Client's requirement. The

Monitor should indicate the quality of air through changing the colours on the

33.1 MR display screen as per the NAAQS standards and should meet the WELL Nos. 1 ₹ 75,000 ₹ 75,000

building standards. The monitor should be a 3 tier architecture including

sensor Hardware, secure cloud infrastructure, monitoring apps including

dashboard, android/IOS. Quoted price shall be inclusive of all necessary

arrangement as required to make the unit proper functional. The System

should provide Soft Assistance in form of Notifications and Alerts for Periodic

Preventive Maintenance.

TOTAL HVAC WORK AMOUNT 306694 742086

Digitally signed by AMIT

S.H. 7 FIRE FIGHTING WORK : CAQM , NEW DELHI ESTIMATE

S.NO DSR 2019 DESCRIPTION OF ITEM UNIT BOQ QTY. RATE DSR Rate NDSR Rate DSR AMOUNT NDSR

after GST AMOUNT

A SPRINKLER SYSTEM

The main fire fighting sprinkler riser pipe including floor isolation valve, flow

indicating switch, inspectors-test-cum-drain assembly and drain pipe in vertical

shafts have already been installed by the main builder. The contractor needs

to make connections, alteration to existing main network only. All works to be

done after seeking permission from building manitenance agency.

1 7 Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe

conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees,

flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling

with suitable clamp/support frame and painting with two or more coats of

synthetic enamel paint of required shade complete as required :

b. 7.2 32 mm nominal bore Metre 9 527.00 560.36 5,043.23

c 7.3 40 mm nominal bore Metre 7 651.00 692.21 4,845.46

d 7.4 50 mm nominal bore Metre 6 787.00 836.82 5,020.90

2 21 Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type

sprinklers of rating 68 degree centigrade with required accessories :

21.1 Pendent Sprinkler Each 28 484.00 514.64 14,409.84

21.2 Upright Sprinkler Each 28 484.00 514.64 14,409.84

21.3 Horizontal side wall sprinkler Each 2 579.00 615.65 1,231.30

21.4 Concealed sprinkler Each 2 1397.00 1,485.43 2,970.86

3 22 Providing & fixing of pressure switch in M.S. pipe lineincluding connection etc. Each 1 1508.00 1,603.46 1,603.46

4 23 Providing & fixing flow switch in following sizes M.S. pipe including connection

etc as required.

Digitally signed by AMIT

S.NO DSR 2019 DESCRIPTION OF ITEM UNIT BOQ QTY. RATE DSR Rate NDSR Rate DSR AMOUNT NDSR

after GST AMOUNT

5 25 Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL

Listed) of stainless steel complete with 15 NPT on reducer thread with maximum

working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet)

25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread

with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes

complete as required.

6 Making connection with existing main header including butterfly valve, flanges

and accessories required.

A.4.a 100 mm nominal bore Each 1 6551.00 6551

A.4.b 150 mm nominal bore Each 0 8629.00 0

7 Providing, fixing, testing and commissioning Ball valve with hard chrome plated

ball inside PTFE (Teflon) seat and ring with chrome plated centre handle with

female BSP2 threads complete in all respect. Minimum working pressure 15

B PORTABLE FIRE EXTINGUISHERS:

1 Providing & fixing of clean agent gas based residue free stored pressure FE-36

Dupont- HFC-236fa (HEXAFLUOROPROPANE – CF3-CH2-CF3) multipurpose type

having 0% ODP with magnetic pressure gauge having the facility to check with

the magnetic pressure kit on site pressurised by dry nitrogen, can height 341MM,

diamater is 108 MM Gross weight 3.6Kg, empty weight 1.6 Kg, discharge time is

minimum 6 sec, controllable discharge machanisim, embossed fire rating as

per the BS EN 3 - 21B, BIS 15683 marked with EPDM Hose with helium leak

detection tested and certificate enclosed, range 4 mtr with plastic yellow

safety seal with pull marked on it.

B.1.a Capacity 2.0 kg Each 1 18962.00 18962

B.1.b Capacity 4.0 kg Each 1 25196.00 25196

2 Providing & Fixing of stored pressure Fire Extinguisher ABC powder type (Mono

Ammonium Phosphate Powder) Magnetic Pressure Gauge having the facility

to check at site, Discharge Time less than 9 Secs, Controllable discharge

mechanism, Range minimum 4 Meters, applicable on Class A,B,C and

A Rating- 21A, B Rating 55B as per BS EN-3 BIS 15683 marked, Can Construction :

Deep drawn & CO2 Mig welded, Valve Construction : Forging & Machining,

Internal Coating of Can : Epoxy Powder coating, External Coating ofCan :

Epoxy Polyster Powder coating, Sheet metal thickness : 1.60MM, Helium Leak

B.2.a. Capacity 2 Kg. Each 1 8349.00 8349

B.2.b. Capacity 6 Kg. Each 1 12720.00 12720

TOTAL FIRE FIGHTING WORK AMOUNT 161872.5388 71778

Digitally signed by AMIT

S.H.8 FURNITURE WORK : CAQM , NEW DELHI ESTIMATE

Sr. No. Item Specification QTY. Unit Price Amount Photo

Supplying and Placing Understructure is made using a combination of 12mm Plywood (As per 1S:303) vertical panels and

Pine-Wood longitudinal members. 2mm thk kraft-board is stapled on the front side for foam sticking surface.the Seat is

made with 100mm PU Slab-stock foam pasted on the seat ply.

12mm PU Slab-stock foam is pasted along the front and sides.The seat is upholstered in fabric.1200mm, 1500mm, and

1800mm Length Sofas are provided with 02 nos of 6A electrical sockets with individual switches. 900 Length Sofas are

provided with 01 nos of 6A electrical sockets with individual switch.The Electricals are safely housed in a box mounted on

30 Lounge area 12 Pax Pine-wood 4 86711 346844

section within the seat & power is supplied through a 1.5 mtr AC cord with ceramic fuse (5A).2. BACK : Understructure is

made using a combination of 12mm Plywood (As per 1S:303) vertical panels and Pine-Wood longitudinal members. 2mm

thk MDF-board is stapled on the front & back side for foam sticking surface. Back is made with 50mm PU Slab-stock foam,

Slab-stock foam is pasted along the back and sides. The back is upholstered in fabric.

LEGS :The legs are made using FSC-certified seasoned Teak-Wood finished with a clear matt coat of PU Lacquer. ASSEMBLY

: The Seat and Back are connected using Bolts, Washers & Nuts. Legs are assembled using Bolts, Washers & Drive-in T-

Nuts.OEM shall be ISO-9001:2015, ISO-14001:2015, ISO-45001:2018, BIFMA and AIOTA certified.

The understructure shall be made up of two different sub asssembly top and Bottom, both aseemblies are made up of

Plywoof of 12mm thick moisture resistance and termite proofing. The sub-assly is connected to each other via metal spring

assembly. The structure is covered with 2mm cardboard to provide a backing surface for foam padding. The seating

surfaces has slab foam of 40 kg per meter cube which is covered with 32 kg per meter cube super soft foam on the top.

The sides of top and bottom structure is covered with slab foam of 28 kg per meter cube. Upholstery consists of 2 separate

31 Toggle upholstered stitched covers made up of 340 GSM polyester fabric for dual tone design. Spring Assembly is made up of 4 12745 50980

Grade II spring with dia. 0.8cm which is being sandwiched between HR plates of 0.315 cm thick clamped with MS Rod

having dis. 0.6cm. The overall dimensions shall be dia. 52.5cm x 52.5 cm height.OEM shall be ISO-9001:2015, ISO-

14001:2015, ISO-45001:2018, BIFMA and AIOTA certified.

Modular Workstation Size 1350X 600 X Ht 1200 with KBPT,Pedestal and CPU torlley, Extended Side Panels of 4ft

Width:Providing and placing panel & tile based modular workstation, with partition thickness as 52.4 mm thk and ht - 1200

including powder coated aluminium trims.Tiles: Combination of top tiles are fabric magneitc/fabric/fabric tackable/white

board/glass writing board/ clear glass tile/ plain metal/ prelam tile. Bottom tiles - Plain metal/ fabric

magnetic/fabric/laminated/prelam.SPLIT Tiles: Combination of two finishes for the top tiles on the user side shall be split

fabric magnetic/fabric tackable/white board/prelam/ plain metal along with split fabric magnetic/fabric tackable/white

board/prelam/ plain metal. INTERMEDIATE BLOCKS Intermediate blocks are given in fabric/DL + Fabric/DL finsh.Wire

Management - Wires shall be taken into the system through cable ducts from the junction boxes and it is carried upto the

panels through concealed conduits inside the blocks.HALF SCREEN WITH FRAME - at intermediate position between 2

32 PMU workstation 1350X600 people and at the end above worktop in clear glass/fabric tackble /laminate/white board finsh.Side panels or legs - out of 8 44871 358968

25 mm thk prelam particle board with flat pvc lipping edge banding considered only on the open end conditions or metal

powder coated legs at the end and shared condition.extended side panel of 4 ft width. System shall also have 120 mm

high powder coated standalone panel legs to give the system an elevated look.Worksurface - out of 25 mm thk prelam

particle board with flat pvc lipping edge banding of size 1350 mm w x 600 mm d.CPU trolley - with castors.KBPT

with/without mousetray - plastic/metal/articulated.The product should be Greenguard ,BIFMA LEVEL, AIOTA,GRIHA, SCS

IAQ, GREENPRO certified.

Digitally signed by AMIT

Sr. No. Item Specification QTY. Unit Price Amount Photo

Providingin place of main table with overall size of table 1650 x 1650 x 750mm. The main table shall be of size 1650 x 750 x

750mm. The side unit shall be 900 x 500 x 750mm. The table is made of 25 mm thick MDF – one side pre-laminate board

confirming to IS-14587:1998 with 0.4 mm PVC membrane pressed on to top. Soft closing access flap within-build power box

are provided on work surface for wire management. The ERU top is made of 25 mm thick MDF one side pre-laminate

board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The modesty panel is made of 25 mm

thick MDF one side pre-laminate board confirming to IS-14587:1998 with 0.4mm PVC membrane pressed on to top. The

understructure is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and approved shade edge banded with

33 Table matching 2 mm thick PVC lipping. The pedestal is made of 25 mm thick Pre-laminated twin board of E1-P2 grade and 1 65521 65521

approved shade edge banded with matching 2 mm thick PVC lipping. Drawer fronts made of 25 mm thick MDF one side

pre-laminate board with 0.4 mm PVC membrane pressed on to top pedestal construction is BOX-BOX-FILE type which uses

powder coated 400 MM long metal Panel Drawer Slides. Drawer extension is 325 MM. Drawers have a soft closing & anti

slam mechanism. Handles are provided for ease of opening. Pedestals are provided with lock for security.

Supplying and Placing The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide,

moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x

53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back

are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement

possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped

spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the

back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted

34 Chair with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable 9 12374 111366

armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The

pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and

fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall

dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Supplying and Placing a The cushioned seat and back assembly consists of seat base moulded in glass filled Poly-amide,

moulded polyurethane foam and upholstered with high stretch knitted polyester fabric. The back size shall be 45.5cm W x

53.0cm H. The HR polyurethane foam used in seat and back cushion is moulded in density 45kg per m3. The seat and back

are firmly connected to the base frame and are cantilevered in such a way that it gives a multi dimensional movement

possibility just with a simple lean on the sides or back, without need for complex manual adjusments. The cantilevered seat

offers impact cushioning while seating and synchronises with the back movement during posture changes. The ‘S: shaped

spines moulded in high strength glass filled Polyamide and the spine connector moulded in glass filled Polyamide form the

back spine structure involved in multi dimensional recline motion. The variable tilt angle recline motion can be adjusted

34 Control room chair with 3 position Tilt limiter feature which is inbuilt in saet base and the tension is user weight dependent. The adjustable 7 12374 86618

armrests assembly consists of armrest housing sliding over the armrest structure, both moulded in glass filled Polyamide. The

pneumatic height adjustment shall have a stroke of 9.2cm.The pedestal is injection moulded in glass filled Polyamide and

fitted with 5 nos. twin wheel castors. The pedestal is 66cm pitch centre diameter and 76cm with castors. The overall

dimensions of the chair shall be 76cmx 76cm x(99.5-108.8cm). The seat height shall be (44.5-53.8cm).

Supplying and Placing in place of 3 seater sofa. The overall dimensions of the sofa shall be 2060W x 905D x 855H. The seat

should be made of PU foam with Density 28 ± 2 kg/cu.mtr having an additional top layer of supersoft PU foam with Density

32 ± 2 kg/cu. Seat should be upholstered with fabric or leatherette. 2) BACK FOAM: The back should be made of PU foam

with Density 28 ± 2 kg/cu. mtr with two additional top layer of supersoft foam of density 32±2 kg/cu. mtr, upholstered with

fabric or leatherette. Understructure should be made up of 1.2±0.1 cm. thick hot pressed plywood (which also shall be

35 Control room 3 seater sofa 2 43458 86916

resistance and termite proof as per IS:303.) and pinewood of cross section deviod of major knots and surface defects 6 nos.

per seat and 3.8mm dia. zigzag spring assembly is mounted over understrucrure for cushioning effect. It should be a

welded assembly made in Stainless steel (grade SS 202) tube & plate with plastic endcap.

Supplying and Placing a Glass shall be 10+/-0.3mm thick black tinted toughened glass UV glued with bushes made in SS

202 grade for fixing with understructure. It shall be a welded assembly made in SS202 grade having dia. 12+/-0.04 as per

36 Corner table IS:1762. overall dimensions of table shall be Width of table= 60.0 cm, Depth=60.0 cm, height=35.1 cm. 3 9169 27507

Digitally signed by AMIT

Sr. No. Item Specification QTY. Unit Price Amount Photo

Total Cost Excluding GST 1134720

Total Cost Including GST 1338969.6

Digitally signed by AMIT

Schedule of Quantities: IP BASED CCTV SYSTEM

S No Description Unit Qty Rate DSR Amount NDSR Amount

SITC of 5MP IR Vandal Proof Dome Network Camera Lens Size:

3.0mm – 13.5mm motorized vari-focal lens, Aperture F1.4 – F3.2,

NDAA Compliance must approved, Security: SSL Encryption, Multi-

User Authority, IEEE802.1x, IP Filtering, HTTPS , IR Distance : 30M

IR, Memory Support : Micro SD 512 GB, Two-way Audio

Communication supported, Audio Compression Algorithm: ADPCM

16K, G.726, G.711 u-Law, G.711 a-Law DC12V/PoE, IP67 and K10

rating, Image Sensor: 1/2.8” CMOS Maximum Resolution: 2592 x

1944, 11, Video Resolution: 4:3 : 2592x1944, 1920x1440,

640x360, Video Compression : H.265, H.264, Dynamic Range:

120dB, True Day & Night: Yes (ICR) MJPEG Scanning Mode:

Progressive Scan COLOR : 0.15 lux @ F2.0 B/W : 0 lux (IR LED

ON), Shutter Speed (Auto) 1/10000s~1s, True day/night, WDR

120db, 3D DNR, HLC & BLC, Quadruple streams, Four Streams

individually configurable, Privacy Masking: 8 Zone, Camera shall

confirm ONVIF Profile S, Smart codec by ROI, MTBF time 1,25,000

Hours @40 degree (Report to be submitted), Inbuilt Analytics

Motion Detection, Alarm in, Tampering and Trip Zone, Shall provide

Quadruple streams, Object , SSL Encryption, Multi-User Authority,

IEEE 802.1x, IP Filtering, HTTPS , Operating Temperature: -40°C ~

+55°C (-40°F ~ +131°F) , Operating Humidity: 0% to 90% non-

condensing, Certification: BIS/UL, FCC, CE approval. MAC

Address: The MAC address of the proposed IP cameras must be

registered in the same name of the OEM. The IP Camera OEM

must confirm that the MAC address of the surveillance cameras;

OUI must be in the name of the OEM. etc complete as per

specifications of this and directions of Engineer-in- Charge

Digitally signed by AMIT

S No Description Unit Qty Rate DSR Amount NDSR Amount

Supply, Installation, Testing & Commissioning of 32 Channel IP

network video recording capability Rack mount NVR with

Redundant Power Supply and minimum 4 Slots, should support

H.264/H.265 compression, network incoming throughput of 850

Mbps and 12MP recording resolution, time division multiplexing,

real time recording of multiple cameras, storing digitized and

compressed images on internal hard disk drives for fast search and

retrieval either locally at the unit, or from a remote workstation using

a Graphical User Interface (GUI), should allow all connected

cameras to be discovered and configured automatically,

simultaneous live view, record, play back, data transmission in real

time, maximum throughput of 400 Mbps, UHD 1920 ips, support

H.264/H.265 compression, 2X – 12X digital zoom in live view

3 mode, 2X – 12X digital zoom in playback mode, time lapse, event, Nos. 0 275,529.00 -

time lapse + event, pre / post-event, panic recording schedule,

recording bitrate control mode: CBR and VBR, alarm, audio, motion,

trip zone, video loss, text-in, system event triggering, fan error,

record failure, storage related alerts and alarm in error, email,

remote notification (call back) to remote work stations, mobile

device push notification, Time-lapse, Event log, Motion, Thumbnail,

Text-in search options, SSL, Password encryption options, network

keyboardfor controlling the NVR and PTZ, 1 Gigabit Remote Client

port, 4 Gigabit ports, ONVIF compliant , output interface 1 HDMI (up

to 4K), 4 internal SATA ports (10TB per SATA) with recording

capacity up to 40 TB. etc complete as per specifications of this and

directions of Engineer-in- Charge.

Supply Installation Testing & Commissioning of 43 inch Full HD LED

5 monitor including wall mount brackets/ clamps/ desk mounting Nos. 0 39,195.00 -

6 Supply and fixing of RJ45 Connector Nos. 6 20.00 120.00

Digitally signed by AMIT

S.H. 9 CIVIL & INTERIOR WORK: AQM , NEW DELHI ESTIMATE

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

A FLOOR LEVELING

A.1 4.1 Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering cum 5.00 6347.75 31,738.75

- All work up to plinth level :

4.1.5A 1:3:6 (1 Cement : 3 manufactured sand derived from Recycled Concrete Aggregate (RCA) : 6 graded stone

aggregate 20 mm nominal size Recycled Concrete Aggregate (RCA)).

2 IPS FLOORING

A.2 11.4 52 mm thick cement concrete flooring with concrete hardener topping, under layer 40 mm thick cement concrete sqm 60.00 978.45 58,707.00

1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) and top layer 12 mm thick

cement hardener consisting of mix 1:2 (1 cement hardener mix : 2 graded stone aggregate 6 mm nominal size)

by volume, hardening compound mixed @ 2 litre per 50 kg of cement or as per manufacturer's specifications.

This includes cost of cement slurry, but excluding the cost of nosing of steps etc. complete.

1 ITALIAN MARBLE

11.51 Providing and laying machine cut, mirror polished, Italian Marble stone flooring laid in required pattern in linear

portion of the building all complete as per architectural drawings, with 18 mm thick stone slab laid over 20mm

(average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @

4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade

including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.

B.1.a 11.51.1 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc sqm 24.00 6603.35 158,480.40

2 8.11 Providing and fixing machine cut, mirror/ eggshell polished , Marble stone work for wall lining (veneer work)

including dado, skirting, risers of steps etc., in required design and pattern wherever required, stones of different

finished surface texture, on 12 mm (average) thick cement mortar 1:3 (1 cement : 3 coarse sand) laid and jointed

with white cement slurry @ 3.3 kg/sqm including pointing with white cement slurry admixed with pigment of

matching shade, including rubbing, curing, polishing etc. all complete as per Architectural drawings, and as

directed by the Engineer-in-Charge.

B.3 8.11.1 18 mm thick Italian Marble stone slab,Perlato, Rosso verona, Fire Red or Dark Emperadore etc. sqm 2.00 10414.80 20,829.60

B.4 VITRIFIED TILE

11.41 Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water

absorption less than 0.08%and conforming to IS : 15622 , of approved make, in all colours and shades, laid on

20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) jointing with grey cement slurry @ 3.3kg/sqm including

grouting the joints with white cement and matching pigments etc., complete.

5 FALSE RAISED FLOORING FOR SERVER ROOM

11.54 Providing and fixing removable raised/false access flooring with system and its components of approved make

for different plenum height with possible height adjustment upto 50 mm, comprising of modular load bearing floor

panels supported on G.I. rectangular stinger frame work and G.I. Pedestal etc. all complete, as per the

architectural drawings, as specified and as directed by Engineer-in-charge consisting of:

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

(a) Providing at required spacing to form modular framework, pedestals made out of GI tube of thickness

minimum 2 mm and 25 mm outer diameter, fully welded on to the G.I. Base plate of size 100mm x 100mm x 3mm

at the bottom of the pedestal tube, G.I. pedestal head of size 75mmx75mmx3.5 mm welded with GI fully threaded

stud 16mm outer diameter with two GI Check nuts screwed on the stud for level adjustment upto 50mm, locking

and stabilizing the pedestal head in position at the required level. The pedestals shall be fixed to the subfloor

(base) through base plate using epoxy based adhesive of approved make or the machine screw with rawl plug.

(b) Stringers system in all steel construction hot dipped galvanized of rectangular size 570x20x30x0.80mm thick

having holes at both ends for securing the stringers on to the pedestal head using fully threaded screws ensuring

maximum lateral stability in all directions, the grid formed by the pedestal and stringer assembly shall receive the

floor panel, this system shall provide adequate solid, rigid support for access floor panel, the system shall provide

a minimum clear uninterrupted clearance between the bottom of the floor for electrical conduits and wiring etc. all

complete as per the architectural drawings, as specified and as directed by the Engineer-in-charge.

(c) Providing and fixing Access Floor panel of 600x600x32 mm medium grade Filled Steel anti static high

pressure Lamination of 800H grade (FS800H). Access Floor panel shall be steel welded construction with an

enclosed bottom pan with uniform pattern of 64 hemispherical cones. The top and bottom plates of Steel Gauges:

top 0.6 mm and bottom 0.7 mm fused spot welded together (minimum 64 welds in each dome and 20 welds along

The panel should be Corroresist epoxy coated for lifetime rust protection and cavity formed by the top and bottom

plate is filled with Pyrogrip noncombustible Portland cementitious core mixed with lightweight foaming compound.

The access floor shall be factory finished with Anti-static High Pressure laminate with Non Warp technology upto

1mm thickness for superior adhesion and Surface flatness within 0.75mm.The panel is to withstand a

Concentrated Load of 363 kgs applied on area 25mm x 25mm without collapse in the centre of the panel which is

placed on four steel blocks. The panel will withstand and Uniformly Distributed Load (UDL) minimum 1250 kg/sqm

and an impact load of 50kg all complete as per the approved manufacturers specification and as per the direction

of Engineer-in-charge. All specification must be printed on the side of the panel to ensure the quality of the

B.5.a 11.54.1 300MM FINISHED FLOOR HEIGHT (FFH). sqm 3.00 5623.95 16,871.85

6 ENGINEERED WOOD FLOORING

B.6.a MR Providing and fixing 15 mm thick Engineered wooden flooring with top layer of 3mm oak wood sanded sq.m 65.00 6,770.00 440,050.00

mat laqueed and bottom layer 10+2 mm of spruce wood of plank sizes of 190/205 mm x 2200mm h

maufatured as per EN 14342:2005+A1 and certificates of JAS2 and CE and PEFC of approved quality

and manufacture, to be laid as per manufacture specification complete as per direction of Engineer in

C FALSE CEILING WORK

GYPSUM BOARD CEILING

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

C.1 MR Providing and fixing false ceiling at all height including providing and fixing of frame work made of

special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm

(both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with

flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash

fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers

of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger

fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre,

to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each

having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I.

intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every

junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30

mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre,

with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section

and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including

jointing and finishing to a flush finish of tapered and square edges of the board with recommended

jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm

on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification

and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame

of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the

Engineer in Charge but excluding the cost of painting with :

12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I sqm 70.00 1,808.00 126,560.00

MINERAL FIBRE ACOUSTICAL SUSPENDED GRID CEILING

C.2 MR 300MM X 1200MM MINERAL FIBRE GRID - Providing & Fixing of Mineral Fibre Acoustical Suspended sqm 38.00 4,092.00 155,496.00

Ceiling System with Bevelled Tegular Edge Planks With 15mm Exposed silhoutte Grid.

The planks should have Humidity Resistance (RH) of 99%, NRC 0.5, Light Reflectance ≥85%, Thermal

Conductivity k = 0.052 - 0.057 w/m K, Colour White, Fire Performance UK Class 0 / Class 1 (BS 476 pt - 6

&7) in module size of 1200 x 300 x 16mm , suitable for Green Building application, with Recycled content

The tile shall be laid on 15 mm wide T - section flanges having rotary stitching on all T sections i.e. the

Main Runner & 1200 mm Cross Tees with a web height of 38mm and a load carrying capacity of 12.67

Kgs/M2 & minimum pull out strength of 100 kgs.. The T Sections have a Galvanizing of 90 grams per M2

and need to be installed with Suspension system. The Tile & Grid system used together should carry a 30

METAL warranty.

C.3 MR Providing & Fixing of Micro-Perforated metal ceiling System consisting of 600x600mm Lay in tiles of pre sqm 6.00 3,750.00 22,500.00

coated galvanised steel in 0.4/0.5 mm thickness in white colour with perforation of 1.5mm dia & open

area of 22% with Freudenberg Soundtex acoustical fleece on the back of the tile to be laid on

Armstrong grid systems with 15mm wide T - section flanges colour white having rotary stitching on the

Main Runner, 1200 mm & 600 mm Cross Tees.

The tiles should have Humidity Resistance (RH) of 100%, NRC of 0.80, Fire Performance A2-s1.d0 in

module size of 600 X 600 mm, suitable for Green Building application, with Recycled content of 25%.

The grid should be 15mm wide T - section flanges colour white having rotary stitching on all T sections

i.e. the Main Runner, 1200 mm & 600 mm Cross Tees with a web height of 43mm and a load carrying

capacity of 23.71 Kgs/M2. The T Sections have a Galvanizing of 120 grams per M2 & passed through 500

hrs of Salt test.

ACOUSTIC LINEAR CEILING

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

C.4 MR Providing and fixing of acoustical baffle ceiling of size 100mm x 25mm with C/c distance between sqm 9.00 12,852.00 115,668.00

baffles of 100/150mm including all necessary accessories & hangigng arrangement as per drawings &

directions of Engineer In Charge

C.5 MR 18MM thk Ply on periphery of the ceiling details as per architectural drawing to be suspended from sqm 9.00 7,010.00 63,090.00

ceiling with a provision for a cut out for light fixtures on it, taking self as well light loads, Complete in all

respect, as specicified Engineer in charge

C.6 MR Providing & fixing Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade sqm 10.00 8,551.00 85,510.00

6063. The baffle blade shall be in size of 100x 30 x 3600mm in Wood grain finish – Pradoo & Cabrueava.

The baffle blade shall be suspended using Slotted U-profile at center-to-center spacing of upto 150mm.

Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps.

50MM THK GI FRAME (FOR 100 MM THK PARTITION)

D.1 MR Providing and fixing metal system up to ceiling height, which includes frame work made of special sqm 74.00 1,308.00 96,792.00

section power pressed/ roll form G.I. sheet with zinc coating of 120 GSM, consisting of Boral U track

52mm wide having equal flanges of 30mm and 0.55mm thick (Base metal thickness) fastened to the

floor slab and ceiling soffit using rawl plugs with screw at 600mm centers, with first & last fixing point at

not greater than 50 mm from either end. Boral C studs 50mm wide having one flange of 34mm, other

flange 36mm, lip size 6 mm and 0.55mm thick installed perpendicularly within the flanges of floor and

ceiling channels located directly opposite to each other at not more than 610mm centers. Maintain 5 to

10mm gap between C Stud and web of U Track.

GLASS WOOL BETWEEN PARTITION (FOR 100 MM THK PARTITION)

D.2 MR Providing and fixing Glass wool insulation with Resin Bonded conforming to IS: 8183 having density 36 sqm 74.00 165.00 12,210.00

kg/m3, for 75mm thick partition wrapped in 200G Virgin Polythene Bags fixed to wall with screw, rawel

plug & washers and held in position by criss crossing GI wire etc. complete as per directions of Engineer-

GYPSUM BOARD FOR 100 MM PARTITION

D.3 MR 12.5 mm Standard board (conforming to IS 2095 Part1 1996; BS 1230: Part1: 1985 for Gypsum Board Type sqm 21.00 1,123.00 23,583.00

1 & BS EN 520: 2004 Type A) is screw fixed to metal system on both sides using “type S” Boral Self tapping

3.5 x 25mm corrosion resistant drywall screws spaced at 200mm centers on all joints and 300mm centers

in the field of boards. Screw fixing is done mechanically. Finally, boards and screw heads are to be

jointed and finished so as to have a flush look which includes filling tapered edge and square edges of

board with Rapid Joint Compound, Paper Tape (As per recommended practice). All perimeters and

penetrations to be sealed with Acrylic sealant as per manufacturer’s specifications.

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

D.4 MR Providing and fixing 12mm thick commercial ply conforming to IS : 1328 type with necessary sqm 172.00 4,982.00 856,904.00

screws/nuts & bolts/ nails, including a coat of approved primer and anti-termite on one face, and

fixed on wooden / steel frame work, complete as per direction of Engineer-incharge (Frame work

shall be paid for separately).

D.5 MR Providing and fixing of 4mm MDF sheet on existing plywood partition / panelling with 4mm wide sqm 45.00 505.00 22,725.00

grooves in approved pattern complete in all respects with adhesive and all accessories as required.The

grooves to be finished using paint of approves shade.

GLASS PARTITION

D.6 MR Providing and fixing 12 mm thick frameless toughened glass Partition of approved brand and sqm 4.00 6,505.00 26,020.00

manufacture, including providing and fixing over aluminium channels embedded in the floor and

supported at the top as detailed. The Partition to be fitted firmly to the true ceiling with necessary

anchors / fastners. All the edges of the glass shall have pencil nosing and machine polished. the joints in

glass shall be filled with colourless silicon sealent all complete as per Direction of Engineer-in-charge.

E WALL FINISHING

E.1 MR Providing and fixing 1mm thick Laminate(as approved) and with painted horizontal and vertical sqm 28.00 1,601.00 44,828.00

grooves to match colour of laminate (as approved), for plain lining / cladding with surface as per

drawings & directions of Engineer In Charge.

E.2 MR Providing and fixing 4mm thick coir veneer board, ISI marked IS : 14842, plain lining with necessary sqm 34.00 4,251.00 144,534.00

screws, priming coat on unexposed surface etc., complete

ACOUSTIC WALL PANEL

E.3 MR Providing and supplying Acoustical Wall Panelling with square edges made of fiber glass substrate sqm 14.00 9,701.00 135,814.00

25mm thick and wrapped on the front side with an acoustically transparent and fire-resistant fabric with

an option of colours as per the choice of the Architect/ Person in-charge of size 2100x600 or 600x600

mm providing a minimum sound absorption level of 0.90 NRC to be affixed to wall using Wall panel

impalers suppied by the manufacturers

CERAMIC GLAZED WALL TILE

E.4 MR Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be Sq.m 21.00 1,506.00 31,626.00

specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle

green, black of size 600x300mm as approved by Engineer-in-Charge, in skirting, risers of steps and

dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3coarse sand) and jointing with grey

cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching

shade complete.

E.5 PLASTER WORKS

E.5.a 13.1 12 mm cement plaster of mix :

E.6 PUTTY PUNNING

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

E.6.a 13.80 Providing and applying white cement based putty of average thickness 1mm of approved brand and sqm 21.00 156.05 3,277.05

manufacturer over the plastered wall surface to prepare the surface even and smooth complete.

DIGITALLY PRINTED FILM ON GLASS AND DOOR PARTITION

E.7 MR Providing & Fixing 3M Frosted Translucent, cast PVC, self-adhesive vinyl, special CRYSTAL-effect film to sqm 8.00 2,429.00 19,432.00

reproduce Sand-blasting effect on glass with customised designs, thickness of 2 mil (0.05mm) without

adhesive & 3mil (0.8)with adhesive having minimum tensile strength of 3.5 pound/inch at 73 F(0.6 kg/cm

at 23 C). Adhesion after 24hrs of installation should be 4 pounds/inch (0.7 kg/cm) on Acrylic, Glass

Polycarbonate: MCS warranty of 3yrs (if exposed to direct sunlight) to 15yrs (indoors) must be endorsed

by 3M India Limited Architectural Market Department. Contractors payment wouldn't be released until

& unless he/she produces orginal warranty certificate from the manufacturer.

MR ROLLER BLINDS

E.8 Supplying and fixing Roller Blinds to the following specifications , Fabric shade as approved, sunscreen, dense basket sqm 20.00 2,551.00 51,020.00

weave 5 % openness factor. Operation: - Manual. Offset side-mounted metal chain operated Mounting: Pocket

mounted. Shade Orientation: Regular roll, shade cloth falls at window side of roller. Configuration: Single band

AVERAGE LENGTH OF BLIND is 2.0 M to 2.5 M. The fabric to be Fire Retardent certified.

E.8a MR BLACKOUT ROLLER BLINDS

Supplying and fixing of Blackout blinds to the following specs. sqm 6.00 3,390.00 20,340.00

Black-out material fibre-glass coated fabric, 12 mils thick, 62 threads per sq in., 0.750 lbs per sq in. (441g per sq mt.)

Operation: - Manual. Offset side-mounted metal chain operated

Mounting: Closure Box in metal

Shade Orientation: Regular roll, shade cloth falls at window side of roller

Configuration: Single band

The Fabric to be as per approved sample (Fabric should be Fire Retardent Certified).

E.8b MR Supplying and fixing of Cellular Semi Opaque 100% Polyester Hardware SpecificationHeadRail: Head rail is 17 mm sqm 8.00 8,575.00 68,600.00

high and 47 mm wide, Thickness 1.00 mm. It is made up of powder coated high strength aluminum alloy covered by

two end caps made up of PVC.Drum & Cradle: They are molded ABS components with high strength metalic drum

which are meant for controlling the lifting cord.Bottom Rail: This is Aluminum Extruded Rail Made up of High Strength

Aluminum alloy, Which is powder coated in white.Installation Bracket: It is made up of mild steel with zinc

plate.Bottom Rail End Cap: It made up of high strength ABS.White Cord: It is made of Nylon braided non stretchable

thread of 1.2 mm thickness.PVC Slip : It is made up of high strength PVC of width 25 mm.Fabric: 100% spun bonded

non-woven polyester translucent fabric Pleat dimension 3⁄4” hexagonal cell with a distinct air pockets Sanitized,

Weight : 145 + 5% GSM, Thickness : 0.14 -0.17, colour fastness of light – 4-5 Grade ( DIN EN ISO105-B02).

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

E.8c MR Supplying and fixing of S-contour blind Roller Tube: Made up of High Strength Anodized Aluminum alloy Extruded sqm 31.00 9,327.00 289,137.00

grooved tube. Size: 40 mm outside diameter (+ 2%); weight = 220gms/running mtr. Control Unit with Clutch

Mechanism: The control unit is made of high strength reinforced plastic. The clutch is of warp spring design. High

carbon steel springs are provided to transmit motion from the driven mechanism. Clutch is operated directionally by

the use of beaded endless chain to raise and lower the blind smoothly to decide height. Idler: Idler is of high

strength reinforced plastic, consisting of an outside sleeve and center shaft. Sleeve provide bearing surface for

center shaft and rotate freely, providing smooth, quiet and long wearing operation. Bottom Rail: This is made up of

high Strength Aluminum alloy Extruded tube, which is powder coated in white. Size: 51 + 1mm Width. ; Weight = 215

gms/running mtr (5%).Fabric : composition 100% polyester &fabric width 275 cm .

MOTOR FOR ROLLER BLINDS

E.9 MR Motorization (for MD cabin) Tubular Motor(RTS) for Roller Blinds / Motor Specs : PREMIUM Motor DM- No. 2.00 27,835.00 55,670.00

35R-6/28 . Radio Transmission System Torque(Nm) 6Nm SPEED (RPM) 28mm Rated Voltage (230 Volt)

Power Consumption(W)121 (W) Rated Current ( A) 0.53 amp Running time before thermal cut of (4

min.) Rated Frequency ( 50 Hz) Degree of Protection – IP44

E.9a MR Providing & fixing Motor Remote 16 channel No. 1.00 20,917.00 20,917.00

E.9b MR Providing & fixing Motor Remote 4 channel No. 1.00 12,675.00 12,675.00

E.10 MR Providing and fixing decorative wall paper on to partitions and wall etc. with approved adhesive over sqm 9.00 2,336.00 21,024.00

panelling in any shape, length etc. including preparing surfaces for wall paper (rate to include wastage

due to various sizes)

1) - Front vinyl and back is non voven

2) - washable 100%

4)- fire retardant

5)- moisture resistant

6)- ac controlling capacity

Marshall Factory series or equivalent

E.11 ACRYLIC EMULSION PAINT

13.82 Wall painting with acrylic emulsion paint, having VOC (Volatile Organic

Compound ) content less than 50 grams/ litre, of approved brand and

manufacture, including applying additional coats wherever required,

to achieve even shade and colour.

E.12 13.68 French spirit polishing :

E.12.a 13.68.1 Two or more coats on new works including a coat of wood filler sqm 34.00 446.25 15,172.50

E.13 MR Providing and fixing 6 mm thick frameless toughened lacqure glass on existing partition/ coloums all sqm 11.00 4,587.00 50,457.00

complete as per Direction of Engineer-in-charge.

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

E.14 ACRYLIC SOLID SURFACE - Providing and fixing counters (vanity or in any other location) with 12 mm

thick acrylic solid surface manufactured as per ISO 19712-2. Solid surface used should be Microbial

resistant and resistant to mould growth, boiling water resistant, heat resistant, impact resistant, stain

resistant, scratch resistant as per ASTM G171 ( min 800 MPa), Green Guard certified and with a fire rating

conforming Class 1 as per BS 476 (Part 6 and 7). Acrylic solid surface having minimum density of 1.65

g/cm3, fixed over Aluminum Sections/19MM Marine Grade ply/ BWP board designed to support a

weight of 25 Kg. per Sqmtr. with suitable flexible adhesives (moisture cured Silicon Sealants) as per

manufacturer's specification and guideline, including fascia and back splash area as per approved

drawings and design. The Joints of Solid surface should be joined with adhesives having Low VOC of

The litre as top

Counter per UL 2818 be

should andfinished

SCAQMD.with moulding of edges, buffing of surface, making of holes for sqm 3.00 13,866.00 41,598.00

plumbing fixtures, flushing of joints, installing of necessary hardware, sealing with silicon sealants, etc. All

complete as per direction of Engineer In charge. The Solid surface used should confirm to impact

resistance of more than 180cm in ball drop test as per ISO EN 438-2 Clause 21, The plan and elevation

area (horizontal and vertical) excluding wash basin area will be measured for payment. Fabrication to

be done as per the manufacturers fabrication manual, Solid surface manufacturer to provide 10 years

installed warranty on the works.

F DOOR AND ACCESSIORES

F.1 21.18 Providing and fixing 12 mm thick frameless toughened glass door sqm 4.00 5325.90 21,303.60

shutter of approved brand and manufacture, including providing and

fixing top & bottom pivot & double action hydraulic floor spring

type fixing arrangement and making necessary holes etc. for fixing

required door fittings, all complete as per direction of Engineer-incharge

(Door handle, lock and stopper etc.to be paid separately).

F.2 MR Providing and fixing ISI marked 40 mm thick flush door shutters conforming to IS : 2202 (Part I) decorative

type, core of block board construction with frame of 1st class hard wood and providing lipping with

2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters with Both Side

Veneer as per specifications and Directions of Engineer In Charge.

F.2.a Double shutter upto, width 1.8m, ht. 2.4m sqm 17,260.00 0.00

F.2.b Single shutter upto , width 1m, ht. 2.4m sqm 8.00 17,260.00 138,080.00

2HOURS FIRE RATED METAL DOOR

F.3 MR SITC of fire door of rating for 120 Minutes, Conforms to IS3614 (PART-2)1992, BS476 (PART 20 & 22) and

Material: Door Frames and Leaves are made from Galvanized Steel

Door Leaves: Constructed from 1.0mm thick galvanized steel sheet formed to provide a 48mm thick fully

flush, double skin door shell with seamless welding joint all around. The internal construction of the door

shall be specially designed with infill to give 2 hours fire rating.

Infill: All the doors will have Honey Comb Crafted Paper or equivalent infill.

Door frame: Produced from 1.6mm galvanized steel sheet formed to single rebate profile of size125mm

x 57mm (+/- 0.3mm) with a maximum bending radius of 1.4mm. The necessary fixing arrangements

should be provided to mount the doorframes to the gypsum partition.

Vision Glass: 2 hours Fire Rated Vision Glass with 6mm thick clear glass in rectangular shape dimensions

of 200mm x 300mm to be fixed as per the given design.

Finish: The door frames and shutters are Zinc Phosphate with epoxy primer and finish with PU paint.

All doors should have suitable locking mechanism with 3 keys each.

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

• Automatic door closures, Seals for Air Tightness and Automatic Door Bottoms should be provided

* Contractor shall obtain and submit certificate

F.3.a Single Shutter, width 1.2m, ht. 2.4m sqm 2.00 76,000.00 152,000.00

F.4 SITC OF FOLLOWING DOOR FITTINGS

F.4.a MR Dorma BB 4330 or equivalent, 5 Knuckle, 2 Ball bearing butt hinges size 4" x 3" x 3mm, in SS 304 and in SSS nos. 9.00 631.00 5,679.00

finish. Suitable for door weights upto 120kgs. Template Drilled (BB 4330)

F.4.b MR Dorma 278a or equivalent with 55mm backset, 20mm square forend prepared for euro profile cylinder nos. 1.00 6,244.00 6,244.00

including strike plate. and EPC 60mm Length both side key operation & Escutcheons in SSS Finish (278a

Dead Lock Type 1 Package)

F.4.c MR Pure 8100 Type 2 or equivalent Package with Pair of Pure 8100 Design Lever Handle on Roses & nos. 1.00 6,181.00 6,181.00

escutcheons. Including 271a Sash lock with 72mm CTC, 55mm Backset 20mm Square forend. EPC 60mm

length one side key other side thumb turn operation (Pure 8100 Type 2 Package)

F.4.d MR Dorma pull Handle or equivalent TGDI-D 300 back to back with adjustable fixing for glass, wood and nos. 2.00 3,406.00 6,812.00

metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling

on the outer surface. Length =300mm, 22mm dia, -SS304 (TGDI-D300)

F.4.e MR Dorma pull Handle TGDI-H 600 back to back with 500mm CTC, adjustable fixing for glass, wood and nos. 4.00 6,734.00 26,936.00

metal doors in satin stainless steel. The pull handles should have supporting washer with raised bevelling

on the outer surface. Length =600mm, 32mm dia, -SS304 (TGDI-H600)

F.4.f MR Dorma rack and pinion door closer or equivalent TS 72 EN size 2-4, with std. arm and with two nos. 2.00 8,251.00 16,502.00

independent closing valves and latching speed adjustable by arm. All adjustment screws face fixed .

Silver finish. As per EN 1154. (TS 72, 2-4, Std arm)

F.4.g MR Dorma floor spring BTS 75V EN or equivalent 1-4 with std. spindle and cover plate. The floor spring with nos. 3.00 16,751.00 50,253.00

backcheck and adjustable closing speed from 175°. With 90° hold open. As per EN 1154. (not suitable

for fire doors) Finish: Satin stainless steel. (BTS 75V EN 1-4 HO)

F.4.h MR PT 10 bottom patch or equivalent with insert for DORMA floor spring spindle, or round pivot 14 mm Ø. nos. 3.00 5,219.00 15,657.00

Finish:Satin Stainless Steel (PT 10)

F.4.i MR PT 20 top patch or equivalent with plastic socket for top pivot 15 mm Ø . Finish:Satin Stainless Steel (PT 20) nos. 3.00 5,219.00 15,657.00

F.4.j MR PT 24 pivot or 15 mm Ø,with fixing plate, material thickness 6 mm, to let into ceiling. Finish: mill (PT 24) nos. 3.00 1,291.00 3,873.00

F.4.k MR center lock Round shape prepared for Europrofile cylinder, single throw, bolt projection 20 mm nos. 3.00 6,426.00 19,278.00

including epc one side key operation and one side knob operation and lock keeper plate. Finish:Satin

Stainless Steel

F.4.l MR Dorma dust excluding socket 3124 or equivalent with 16mm dia hole, fully morticed on the floor. satin nos. 2.00 756.00 1,512.00

F.4.m MR Dorma lever action flush bolt or equivalent with 19mm projecting bolt L=172 mm for wood door in satin nos. 2.00 1,228.00 2,456.00

chrome (3100-0)

F.4.n MR Dorma floor stop half dome or equivalent with 45mm dia with fixing accessories, in satin Chrome (3108) nos. 4.00 372.00 1,488.00

G DISMANTALING AND DISPOSAL OF EXISTING INTERIOR INFRASTRUCTURE

15.23 Dismantling tile work in floors and roofs laid in cement mortar including stacking material within 50

G.1 15.23.2 For thickness of tiles above 25 mm and up to 40 mm SQM 77.00 113.35 8,727.95

G.2 MR Dismantaling of existing wooden flooring including stacking of serviceable material and disposal of SQM 1.00 221.00 221.00

unserviceable material within 50 metres lead.

G.3 MR Based on Dismantling tile work in Wall dado laid in cement mortar including stacking material within 50 metres SQM 2.00 113.35 226.70

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

G.4 15.25 Dismantling stone slab flooring laid in cement mortar including stacking of serviceable material and SQM 2.00 266.45 532.90

disposal of unserviceable material within 50 metres lead.

G.5 15.56 Dismantling old plaster or skirting raking out joints and cleaning the surface for plaster including disposal SQM 3.00 54.65 163.95

of rubbish to the dumping ground within 50 metres lead.

G.6 15.7 Demolishing brick work manually / by mechanical means including stacking of serviceable material

and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

G.7 15.7.4 In cement mortar CUM 5.00 2060.20 10,301.00

15.12 Dismantling doors, windows and clerestory windows (steel or wood) shutter including chowkhats,

architrave, holdfasts etc. complete and stacking within 50 metres lead:

G.8 15.12.1 Of area 3 sq. metres and below EACH 2.00 367.20 734.40

G.9 15.12.2 Of area beyond 3 sq. metres EACH 2.00 502.75 1,005.50

G.10 15.57 Dismantling aluminium/ Gypsum partitions, doors, windows, fixed glazing and false ceiling including SQM 145.00 56.35 8,170.75

disposal of unserviceable material and stacking of serviceable material with in 50 meters lead as

directed by Engineer-in-charge.

15.2 Demolishing cement concrete manually / by mechanical means including disposal of material within 50

metres lead as per direction of Engineer-in - charge.

G.11 15.2.1 Nominal concrete 1:3:6 or richer mix (i/c equivalent design mix) CUM 3.00 2434.25 7,302.75

15.45 Dismantling C.I. pipes including excavation and refilling trenches after taking out the pipes, manually /

by mechanical means breaking lead caulked joints, melting of lead and making into blocks including

stacking of pipes & lead at site within 50 metre lead as per direction of Engineer-in-Charge:

G.13 15.44 Dismantling G.I. pipes (external work) including excavation and refilling trenches after taking out the

pipes, manually / by mechanical means including stacking of pipes within 50 metres lead as per

direction of Engineer-in-Charge:

G.13.a 15.44.1 15 mm to 40 mm nominal bore RM 3.00 149.80 449.40

G.13.b 15.44.2 Above 40 mm nominal bore RM 3.00 161.40 484.20

G.14 15.52 Dismantling of flushing cistern of all types (C.I. /PVC/Vitrous China) including stacking of useful materials Nos 1.00 112.05 112.05

near the site and disposal of unserviceable materials within 50 metres lead.

G.15 MR Based on Dismantling o Wash basins, Urinals, WC including stacking of useful material near the site and disposal of Nos 2.00 112.05 224.10

item No 15.52 unservicable materials within 50 metres lead

G.16 15.3 Demolishing R.C.C. work manually / by mechanical means including stacking of steel bars and disposal cum 2.00 3551.25 7,102.50

of unserviceable material within 50 metres lead as per direction of Engineer-in-Charge.

G.17 15.5 Extra for cutting reinforcement bars manually / by mechanical means in R.C.C. or R.B. work (Payment sqm 2.00 1147.20 2,294.40

shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer - in -

G.18 15.6 Extra for scrapping, cleaning and straightening reinforcement from R.C.C. or R.B. work. kg 3.00 9.05 27.15

1.1 Carriage of material by mechanical transport including loading unloading and stacking

1.1.1 Lime, murrum, building rubbish

H 6.47 Providing and laying autoclaved aerated cement blocks masonry with 150mm/230mm/300 mm thick cum 2.00 8333.65 16,667.30

AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel

level with approved block laying polymer modified adhesive mortar all complete as per direction of

Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for seperately).

I SKIRTING & TRIM

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

I.1 MR Providing and fixing 1.5 to 2mm thick 50mm high extruded SS anodized aluminium skirting as per IS Rmt 67.00 575 38,525.00

standard pasted/fixed over 12 mm thick BWP ply with aluminium strip as per Architects approval.

I.2 MR Providing and fixing Window Cill of upto 450 mm wide, in 19mm thick pre-polished granite slabs of Rmt 21.00 1,622 34,062.00

approved shade, fixed on a bed of cement mortar 1:4, not more than 25mm thick, flushed with the

finished surface of wall, inclusive of pointing joints with neat cement slurry with pigmented additives to

match the shade of the tile, 6mm groove in the wall at the junction of granite and finished surface of

wall etc complete. Cost of pre-Polished Granite Rs.1,300/- per Sqmt.

J COUNTER WORK

J.1 MR Meeting Room Credenza: Meeting Room Credenza of size 450 deep x 3000 avg. length 800 high made Nos 1.00 15,667 15,667.00

up of 20 mm thk laminate finished top and sides,shutters etc. complete with necessary hardaware and

fittings as design & Drawing.

MR Providing and constructing full height storage of width and size as per drawings, with top, sides and

bottom in 19 mm thick commercial ply, back in 8mm thick commercial ply, intermediates in 19 mm thick

commercial ply, shutter hollow core with framework as per drawings in 19 mm thick commercial ply,

with 4mm thick commercial ply panel. All external surfaces to be finished in approved laminate, with

balancing laminate on the interior surface. All exposed edges to be finished in approved PVC edge

binding. Rate to include hardware such as approved locks, auto closing hinges for shutters, approved

handles, door stop, tower bolt, etc. complete.

MR 700 MM DEEP VENDING COUNTER :- Providing and fixing vending counter at pantry, counter made of

20 mm thk. (finished) granite top over BWP with 20x20 groove,base cabinet made of laminated shutter

of 19mm thick BWP(100% Gurjan with CCP technology) with shelves and partitions in balancing

laminate with edge lipping, 50mm high aluminium skirting, The rate inclusive of necessory hardwood &

ply backing, laminate finished, Sink with necessaary cut-outs,Hardware- SS Anodised Hettitch shutter

pulls 045206, self-closing hinges, spring loaded shutter latch inside, all cabinet hardware to be HETITCH

make & as/Architects approval Complete as per design and drawing. (Cost of Polished Granite Rs.

1,200/- per Sqm.)

K CEILING COVE

K.1 MR Ceiling Coves: Providing and making ceiling coves in 12mm thick gypboard/ply including necessory Rmt 26.00 204 5,304.00

support etc. complete with plastic emulsion paint and as per drawing.(Size-150 x 150mm)

L.1 MR Providing and fixing pelmets to Blinds made of 19 mm thick commercial ply, having clear internal Rmt 16.00 887 14,192.00

dimensions as 250 x 300mm, finished in approved laminate on all exposed surfaces from all external

surfaces and balancing laminate on all internal surfaces, supported from RCC ceiling slab by necessary

framework, giving additional supports in MS angles etc. complete. All exposed edges to be finished in

6mm thick TW beading and finished in approved colour.

M MR COMPANY LOGO:- Providing and fixing three dimensional signage in Acrylic Sheet finish to match nos 0.00 47,832 0.00

brand colour shade of size approx. 450 mm x 1800 mm as per clients artwork. Average thickness of

Signage letter 25 mm acrylic & laser cut as per design and shop drawing, Base Rate Rs.40,500/-

Digitally signed by AMIT

S.NO DSR Ref. No. DESCRIPTION OF ITEM

UNIT BOQ Qty DSR RATE NDSR Rate DSR AMOUNT

N.2 consultancy Services for Preparation of Architechratural drawings, shop drawings etc LS 0.00 4,200,000 0.00

O.1 MR Supplying and fixing of Toilet signages: Size: 150mmx 150mm imp.aluminum profile with 3 mm acrylic nos 2.00 686 1,372.00

Gents/Ladies pictograph printed on canvas: GENTS, PHYSICALLY CHAL., LADIES, PANTRY, MEETING

O.2 MR Providing and Fixing the Fire Exit Signages made up of Rigid integral PVC Cladded with Photo nos 2.00 991 1,982.00

luminiscent (Glow in Dark) material with computer cut vinyl lettering on it. Double sided and Single

sidded.As per architects Instruction. Fire makes and codes- readily available Make: Prolite

O.3 MR FIRE EVACUATION SIGNAGE - Fire Evacuation Signage: Material Clip-on (Aluminum Frame) with digital nos 1.00 3,466 3,466.00

print with lamination Fire Plan as per your Specification and Pasted the double sided 3M Tape. Size A3

O.4 MR Providing and fixing PUSH/PULL signage for all doors nos 6.00 298 1,788.00

O.5 MR IN CASE OF FIRE USE STAIRS' photo luminescent sign size: 200 x 200mm nos 1.00 451 451.00

P Providing & Fixing Passive Fire Stop Treatment as per:

P.1 MR Providing Fire expanding foam with minimum 2 hours fire rating when tested in accordance with BS 476 sqm 4 15528 62112

part 20 and UL 1479 for horizontal openings in fire rated floors or slabs and vertical openings in walls

made of concrete/ masonry or Gypsum for passing service shafts. The expanding foam expands seven

times its volume to fill the cavity at the time of dispensing the material and shall fully cure within two

minutes after dispensing. The service lines could be of various types like electrical cables, cable trays or

metal pipes etc. The product shall be age tested for 30 years as per Dafstb and DIBT standards. The

product shall provide water tightness when tested for W rating as per UL standards and shall be tested

for providing a sound insualtion of 50 when tested in accordance with ASTM E 90. packing.

The Application area should be cleaned. A suitable backing material should be used around metal

pipes or electrical cables and then the FireStop sealant should be dispended, the first few drops such

that only properly mixed materials will be used inside the opening (This can be known when the color of

the foam is red and not pale yellow).

UL Classified, FM,LPCB,BS 476-20,pr EN 1366-3

TOTAL CIVIL & INTERIOR WORK AMOUNTS 424,058.55 3,932,275.00

Digitally signed by AMIT

S.H.10 PLUMBING WORK: AQM , NEW DELHI ESTIMATE

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

1 Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C.

waste fittings complete.

a MR 32mm flexible pipe Each 1.00 112.00 112.00

2 Providing and Fixing soil, waste and vent pipes

a 17.35.1.2 100mm dia Centrifugally cast (spun) iron socketed pipe as per IS: 3989 M 2.00 1,180.75 1,255.49 2,510.98

b 17.35.2.2 75mm dia Centrifugally cast (spun) iron socketed pipe as per IS: 3989 M 2.00 1,186.00 1,261.07 2,522.15

3 17.70.2 Providing and fixing PTMT Bottle Trap for Wash basin and sink. Each 2.00 375.65 399.43 798.86

Bottle trap 38 mm single piece moulded with height of 270 mm, effective

length of tail pipe 260 mm from the centre of the waste coupling, 77 mm

breadth with 25 mm minimum water seal, weighing not less than 263 gms

4 Providing and Fixing trap of self cleansing design with screwed down or hinged

grating with or without vent arm complete, including cost of cutting and making

good the floor and walls

a 17.60.2.1 100mm inlet and 75mm outlet Sand cast iron S&S as per IS - 3989 Each 2.00 1,975.15 2,100.18 4,200.35

5 Painting sand cast iron/centrifugally cast (spun) iron soil, waste vent pipes and

fittings with paint of any colour such as chocolate grey or buff etc. over a coat

of primer (of approved quality) for new work.

6 Providing and fixing MS holder-bat clamps of approved design to Sand Cast

iron/cast iron (spun) pipe embedded in and including cement concrete blocks

10x10x10 cm of 1:2:4 mix (1 cement: 2 coarse sand : 4 graded stone aggregate

20mm nominal size) including cost of cutting holes and making good the walls

7 Providing and fixing bend of required degree with access door insertion

rubber washer 3mm thick bolts and nuts complete

a 17.38.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 1.00 705.20 749.84 749.84

b 17.38.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 1.00 522.80 555.89 555.89

8 Providing and fixing plain bend of required degree

a 17.39.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 1.00 570.05 606.13 606.13

b 17.39.2.2 75mm Sand Cast iron S&S as per IS-3989 Each 1.00 390.50 415.22 415.22

9 Providing and fixing heal rest sanitary bend

a 17.40.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 1.00 548.70 583.43 583.43

b 17.40.2.2. 75mm Sand Cast iron S&S as per IS-3989 Each 1.00 504.30 536.22 536.22

Digitally signed by AMIT

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

10 Providing and fixing single equal plain junction of required degree with access

door, insertion rubber washer 3 mm thick, bolts and nuts complete.

a 17.44.1.2 100x100x100 mm Sand cast iron S&S as per IS - 3989 Each 1.00 811.90 863.29 863.29

11 Providing and fixing collars

a 17.57.1.2 100mm Sand Cast iron S&S as per IS-3989 Each 2.00 513.15 545.63 1,091.26

12 Providing lead caulked joints to sand cast iron/centrifugally cast (spun) iron

pipes & fittings of dia

13 17.59 Providing and fixing MS stays and clamps for sand cast iron/ centrifugally cast

(spun) iron pipes of diameter.

14 18.51 Providing and fixing C.P. brass long body bib cock of approved quality

conforming to IS standards and weighing not less than 690 gms.

15 Providing and fixing C.P. brass stop cock (concealed) of standard design and

of approved make conforming to IS : 8931.

16 Providing and fixing C.P. brass angle valve for basin mixer and gyser points of

approved quality conforming to IS : 8931

17 17.61 Cutting chases in brick masonry walls for following diameter sand cast

iron/centrifugally cast (spun) iron pipes and making good the same with

cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate

12.5 m nominal size) including necessary plaster and pointing in cement mortar

1:4 (1 cement : 4 coarse sand) :

18 18.76 Cutting holes upto 30 X 30 cm in walls including making good the same.

18.76.1 With common burnt clay F.P.S. (non modular) bricks Each 1.00 416.80 443.18 443.18

19 18.78 Making chases upto 7.5 X 7.5 cm in walls including making good after housing M 1.00 202.90 215.74 215.74

Digitally signed by AMIT

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

20 Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having

thermal stability for hot & cold water supply, including all CPVC plain & brass

threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing.

This includes jointing of pipes & fittings with one step CPVC solvent cement and

the cost of cutting chases and making good the same including testing of joints

complete as per direction of Engineer in Charge.

Concealed work including cutting chases and making good the walls etc.,

a 18.8.1 15mm nominal outer dia pipes M 9.00 497.80 529.31 4,763.80

b 18.8.2 20mm nominal outer dia pipes M 8.00 537.60 571.63 4,573.04

c 18.8.3 25mm nominal outer dia pipes M 4.00 627.25 666.95 2,667.82

21 Providing and fixing gun metal gate valve with C.I. Wheel of approved quality

22 Providing and fixing unplasticised PVC connection pipe with brass unions.

a 18.21.1.1 30cm lengh &15 mm nominal bore Each 1.00 85.00 90.38 90.38

23 MR Providing and fixing white vitreous china clay wall mounted European type Each 2.00 23,411.00 46,822.00

Water Closet (EWC) with dual flush concealed cistern of approved make, of

approved shade similar to Jaquar Kubix KUS-WHT-35953BI or equivalent

including matching shade of plastic seat and lid cover, fittings, connectors,

necessary hanging arrangement, rubber buffers etc. including cutting and

making good the wall and floors wherever required, making connections to soil

/ vent pipe etc., complete in all respects inclusive of cost of all required fittings,

fixtures, materials, labour, tools, tackles etc. as per specifications and direction

of Engineer-in-Charge.

24 MR Providing and fixing glazed vitreous China rectangular wash basin of 560x410

mm size of approved make similar to Jaquar Kubix KUS-WHT-35935 or similar with

MS or CI brackets painted white, C.P. brass chain with rubber plug, 32 mm CP

brass waste coupling of standard pattern, 32 mm CP brass bottle trap and

union, 32 mm dia C.P. pipes to wall flange etc. including cutting and making

good the walls & floors where required complete in all respects inclusive of cost

of all required fittings, fixtures, materials, labour, tools, tackles etc. as per

specifications and direction of Engineer in Charge

24.a a) White colour Each 2.00 7,385.00 14,770.00

25 17.10 Providing and fixing stainless steel sink of approved make with 40mm dia CP

brass waste coupling of standard pattern, CP brass chain & plug, 40 mm dia

PVC waste, CP grating including fixing under counter top, cutting and making

good the walls & floors where required complete in all respects inclusive of cost

of all required fittings, fixtures, materials, labour, tools, tackles etc. as per

specifications and direction of Site Engineer.

Digitally signed by AMIT

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

25.a 17.10.1 a) Stainless steel sink single bowl with drain board of overall size Each 0.00 6,945.60 7,385.26 0.00

510mmx1040mm, 250mm deep

26 MR Providing and fixing ivory coloured vitreous china flat back urinal basin set of Each 1.00 24,409.00 24,409.00

Urinals similar to Jaquar URS-WHT-132530 or equivalent approved make with

auto sensor flushing system with built in sensor including spreader, all fittings,

brackets for wall fixing, connection pipe, waste pipe etc. for individual urinal

including cutting and making good the walls and floors wherever required etc.,

complete in all respects inclusive of cost of all required fittings, fixtures, materials,

labour, tools, tackles etc. as per specifications and direction of Site Engineer.

27 MR Providing & fixing 6mm thick, copper back finish, looking mirror of required size, Sqm 2.00 3,067.00 6,134.00

made of float sheet glass of best quality & approved make, over 12 mm thick

marine board fixed to rawl plug with round head screws and washers including

teak wood beading with melamine polish all around, complete in all respects

inclusive of cost of all materials, labour, tools, tackles etc. as per specifications

and direction of EIC.

28 MR Providing and fixing Manual CP Central hole single lever wash basin tap & Each 2.00 6,500.00 13,000.00

popup waste system with 2 nos. 10 mm dia. 450mm long copper pipes and

brass nuts, size 15mm including cutting and making good the walls where

required complete in all respects as per direction of Engineer-in-Charge.

29 MR Providing and fixing CP brass tap with CP brass flange including cutting and Each 2.00 20,664.00 41,328.00

making good the walls where required complete in all respects inclusive of cost

of all materials, labour, tools, tackles etc. as per specifications and direction of

Site Engineer. Two way Bib Cock with wall flange.

30 MR Providing & fixing health faucet/ hand shower ABS body with 1 meter long PVC Each 2.00 1,673.00 3,346.00

tube and wall hook with flexible tube 8mm dia 1.5 m long.

31 22.5 Providing and laying water proofing treatment in sunken portion of WCs, Sqm 21.00 617.05 656.11 13,778.29

bathroom etc., by applying cement slurry mixed with water proofing cement

compound consisting of applying : a) First layer of slurry of cement @ 0.488

kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This

layer will be allowed to air cure for 4 hours. b) Second layer of slurry of cement

@ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm.

This layer will be allowed to air cure for 4 hours followed with water curing for 48

hours. The rate includes preparation of surface, treatment and sealing of all

joints, corners, junctions of pipes and masonry with polymer mixed slurry.

32 22.14.1 Grading roof for water proofing treatment with cement concrete 1:2:4 (1 Cum 2.00 8,042.30 8,551.38 17,102.76

cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size).

Digitally signed by AMIT

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

33 MR Providing & fixing Twin Toilet Paper Holder - Steel Twin Toilet Paper Holder - Nos. 2.00 3,780.00 7,560.00

Steel,Application : WC Cubicle Area

34 MR Provoding & fixing Manual operated Hand Sanitiser Dispenser floor standing- Nos. 1.00 16,234.00 16,234.00

High Traffic Providing & Fixing of Hand Sanitizer , EHST3S or equivalent

Providing & fixing Manual operated SOAP DISPENSER pluto PSD101 or equivalent

36 MR Providing & fixing SS finish sensor based hand dryer Pluto or equivalent model Nos. 1.00 32,930.00 32,930.00

37 MR Providing & fixing SS waste receptable bin of Kinox KWR or equivalent. Nos. 1.00 13,500.00 13,500.00

38 MR Supply and Installation of modular WC cubicles of width and depth as per Nos. 1.00 48,642.00 48,642.00

specifications/ drawings. Cubicle height to be upto 2100 mm.

ITEM DESCRIPTION

Made from solid grade compact high pressure laminate as per

IS:2046 manufactured under high specific pressure > 5 MPa and temperature

>120oC with bunch of kraft papers impregnated with thermosetting phenolic

resin and decorative papers made of Alpha cellulose fiber impregnated with

thermosetting melamine resin which provide superior scratch, abrasion, heat,

chemical, impact, graffiti & moisture resistance along with anti-bacterial

properties. Panels have a black core that when machined, presents a

distinctive black edge. Panel thickness 12 mm. Design no. as specified by Arch.

/ Engr. in suede finish. Size of panels to be as per drawing and verified as per site.

Digitally signed by AMIT

S NO. DSR NO. DESCRIPTION OF ITEM UNIT BOQ DSR RATE DSR Rate after GST NDSR Rate DSR AMOUNT NDSR AMOUNT

2019 QTY. Multiplication

HARDWARE & ACCESSORIES

• Rectangular head frame structure made from Stainless steel grade 304.

Surface finish to be brush type. A thin plastic film pasted for surface protection.

Size to be 55mmx42mmx1.6 mmT.

Corner joinery section made from Stainless steel grade 304. Surface finish to be

brush type. A thin plastic film pasted for surface protection. Size to be

35mmx15mmx0.8 mmT.

Wall joinery section with hamming profile made from Stainless steel grade 304.

Surface finish to be brush type. A thin plastic film pasted for surface protection.

Size to be 21mmx16mmx0.8 mmT.

• Adjustable Palm Design Pedestal Footing of base diameter 64 mm made from

Stainless steel grade 316 giving a clearance height of 150 mm. Surface finish to

• Spring loaded Butt Hinges made from Stainless steel grade 304. Surface finish

to be matt type. Covers to be lacquer coated.

• Conical shape Coat hook with rubber stopper made from Stainless steel

grade 304. Surface finish to be matt type.

• Round Door knob diameter 30 mm with grooves for better hand grip made

from Stainless steel grade 304. Surface finish to be matt type.

• Rotating Thumb-turn locking system with privacy indicator made from Stainless

steel grade 304. Surface finish to be matt type.

• Anti-noise rubber padding of thickness 2 mm and width 10 mm

• Stainless steel grade 304 screws.

Partition system made out of Aluminium Extrusions around 2mm thick and

anodised around 15 micron.Size 25x45mm at top and bottom .The Partition to

have vertical portals to house the service cable.The portals to be on the door

side as well as on the corner and junction with solid wall.

The wall starter shall be 105/more x105mm/more.The partition sections to be

suitale to be clubbed with any type of door frame and door shutter(Sliding or

hinged door). The sections to be stable enough to accept glass thickness 10mm

toughened glass also.The partition sections to be available in anodized finish in

any RAL color as approved by the architects.The Partition should be

demountable and easy to install and maintain.The glass joints to be finished with

matching aluminium alloy I,T and corner sections suitable for 10mm thick

Cubicles: Std Sizes (W x D x H)- 900 mm x 1550 mm x 1980 mm ( Height is

including 150 mm gap from bottom) Door Size- 600 mm

39 MR Providing and fixing urinal divider panel made up of 12mm thk. Compact Nos. 1.00 6,729.00 6,729.00

laminate using baracket.

TOTAL PLUMBING WORK AMOUNT 65,110.43 278,728.00

Digitally signed by AMIT

S.H. 4 : LAN WORK CAQM , NEW DELHI ESTIMATE

S.NO DESCRIPTION OF ITEM UNIT BOQ QTY. RATE AMOUNT

1 PASSIVE LAN SYSTEM

1.1 Supply, Installation, Testing & Commissioning of 24 Port loaded Jack Panel Nos 2.00 12500 25000.00

CAT 6A, Staggered 24 Port panel in 1U Rack Unit, Copper Alloyed Contact

Material, EIA 568A/B wired, PC + glass fiber, UL 94V-0, black color, Front Port

Labelling, 22-24 AWG Wire Accumulation complete as required

1.2 Supply, Installation, Testing & Commissioning of quad face plate having Nos 22.00 300 6600.00

provision for four I/O along with spring type shutter for dust proof, made of ABS

PVC plastic complete as required

1.3 Supply, Installation, Testing & Commissioning of dual face plate having Nos 2.00 280 560.00

provision for one I/O along with spring type shutter for dust proof, made of ABS

PVC plastic complete as required

1.4 Supply, Installation, Testing & Commissioning of CAT 6A Information Nos 28.00 450 12600.00

Outlet,Universal label permits T568A or B wiring, UL® Listed, meets all TIA and

ISO requirements.Complete in all respect as required by the site.

1.5 Supplying and drawing of LSZH UTP 4 pair CAT 6A LAN low smoke Cable in the Mtrs 1,700.00 85 144500.00

existing surface/ recessed Steel/ PVC conduit as required.

1.6 Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 2 Mtr, Nos 21.00 445 9345.00

4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim

clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed,

meets all TIA and ISO requirements. Complete in all respect as required by site

1.7 Supply, Installation, Testing & Commissioning of CAT 6A Patch Cord LSZH 1 Mtr, Nos 43.00 425 18275.00

4 pair 26 AWG stranded copper wire, Pre-terminated with RJ45 plugs, Slim

clear anti-snag slip on boots, Suitable for EIA 568A or 568B wiring, UL® Listed,

meets all TIA and ISO requirements. Complete in all respect as required by site

Digitally signed by AMIT

1.8 Supply, Installation, Testing and Commissioning of 42 U Networking Rack Nos - 75000 0.00

(600*800), Front Glass Door Unit and Grilled back door unit, lockable Door unit,

Load Rating of Min 450 Kg. Pillar of frame must be aluminum and Rest plated

are steel, Powder Coated Rack with Castors (4nos.), Fan (4 Nos.), Cable

Manager (2Nos), Full Tray Unit (1 Nos.), PDU (1Nos.) complete in all respect as

1.9 Supply, Installation, Testing & Commissioning of 6 Core Armoured Multi Mode Mtrs 15.00 190 2850.00

Fiber optic cable, Central Lose Tube With Jelly Compound, Corrugated steel

tape armoured, Heaving 1300 nm Wavelength in the existing surface/

recessed Steel/ PVC conduit as required.

1.10 Supply, Installation, Testing and Commissioning of Multi Mode fiber SC-LC Nos - 2200 0.00

Duplex patch cord of 2 Mtrs. for Gigabit Connection between Patch Panel

and Switch complete as required.

1.11 Supplying, Installation, Testing and Commissioning of fiber optic SFP + fiber Nos - 9500 0.00

patch cord of 3 meter length having SFP+ modules at both ends complete as

1.12 Supply, Installation, Testing & Commissioning of Fiber optic Mini GBIC SFP Trans Nos - 14500 0.00

receiver 10G for network switch with Built-in spring latch for easy module

removal, Hot Swappable, Comply IFC and FDA Safety Standards complete as

1.13 Supply, Installation, termination & testing of 2 mtr length SC pigtails 9/125 Nos 1.00 950 950.00

micron for Multi Mode Pigtails complete as required.

1.14 Supply, Installation, Testing & Commissioning of 12 Port Unloaded Line Nos 2.00 18500.00 37000.00

Interface Unit LIU, 19",1u Rack Mountable unit with splice Tray Holder, Cable

Guide, Fiber Management and Splicing of Pigtails and Fiber Cables Including

Joints and Connectors complete as required.

TOTAL LAN WORK AMOUNT 257,680.00

Digitally signed by AMIT

SCHEDULE OF QUANTITIES - IPPBX & DISPLAY

S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

S NO DESCRIPTION UNIT QUANTITY RATE TOTAL AMOUNT

Supply, Installation, Testing & Commissioning of Server based Communication System

with all the required Software licenses and Hardware - IP-PBX/IP Telephony

Communications Server: The IP Telephony Solution shall support the following Services -

Voice, IM, Presence and Audio Conference The IP Telephony Solution should support

H.323 and SIP The Solution should support the following Trunks - FXO, E1 PRI and SIP

The IP Telephony solution should incorporate all licenses for the Phones and Trunks

Solution should support all Extensions from Day 1 with future scalabilityupto 500 users.

Licenses for all Phones supplied should be provisioned on Day1 Solution should support

Hard 70 IP Phones, Rack mount architecture, complete as required and as per technical

specifications.or its equivalent specifications

Supply, Installation, Testing & Commissioning of Color display—2.8 inches x 2.1 inches

(7.0 cm x 5.3 cm)—Diagonal width: 3.5 inches (8.8 cm)▪ 8 buttons with dual LEDs (red,

green)▪ 4 softkeys▪ Hard buttons for phone, messages, contacts, history, home, navigation

cluster,headset, speaker, volume, mute▪ LEDs for speaker, mute, headset, message,

history▪ 24 administrative buttons▪ Wideband audio in handset and headset▪ Full duplex

speakerphone ▪ Ergonomic hearing aid compatible handset supports TTD acoustic

coupler▪ Message waiting indicator▪ Mute indicator with optional mute alerting▪ IC call

alerting with 360-degree visibility▪ Rich, classic, alternate, and downloadable ringtones▪

Dual-position stand, optional wallmount stand▪ Gigabit Ethernet (10 / 100 / 1000) line

interface▪ Second Ethernet interface 10 / 100 / 1000 Mbps▪ PoE Class (IEEE 802.3af)

registers as class 1 device and supports 802.3az▪ Optional AC to 5 volt adapter▪ Order

Custom Bezels / Faceplates▪ SIP & H.323 protocol support▪ Standards-based codec

support: G.711, G.726, G.729A / B, G.722, Opus.▪ Zero touch deployment via Device

Enrollment Services Support▪ Supports the following languages: Arabic, Brazilian

Portuguese, Simplified Chinese, Dutch, English, Canadian French, Parisian French,

German, Hebrew, Italian, Japanese, Korean, Polish, Latin American Spanish, Castilian

Spanish,Thai, Turkish, and Russian. or its equivalent specifications

Supply, Installation,Testing and commisioning of IP phone license complete as required

Digitally signed by AMIT

S.No. Item Specifications Makes Qty Unit Price Total Price

Supply, installation, testing and commissioning of 19.68 x 7.75 feet indoor COB LED display with 1.25 mm pixel pitch, LED

control system with power distribution unit, mechanical structure, and complete installation, testing, and commissioning.

The LED wall must meet specifications such as MIP technology, micro-in-package pixel configuration, pixel density of at

least 640,000 pixels/m², 800 cd/m² minimum brightness with 0–255 dimming, 20,000:1 contrast ratio, 3840 Hz refresh

rate, 16-bit color processing, 280 trillion colors, 160° viewing angles, 100,000-hour lifespan, AC 100V–240V power input,

less than 275 W/sqm max power consumption, and IP30 grade with front service access. BIS certification is mandatory for

LED tiles/cabinets, with all solution components (LED cabinet, controller, processor, PDU) sourced from the same OEM.

Further, the OEM must have a government-approved R&D center in India, be present with a registered office in India for

at least 15 years, possess turnover of at least ₹500 crores in the last financial year, and certifications including ISO

9001:2015, ISO 14001:2015, OHSAS 45001, and ISO 27001:1. Calibration of LED tiles/cabinets before and after installation

1 LED Video wall Delta/NEC/Barco 1 ₹ 25,000,000.00 ₹ 25,000,000.00

using an OEM-provided luminance meter with a valid calibration certificate is required, along with detailed proof of

capability, completed large-scale projects (at least 100 outdoor LED screens and 20 active indoor LED screens in similar

pixel pitch for government/PSU clients), local service centers in major cities with GST registration, dedicated after-sales

support, factory license, and government R&D approval. Safety and electrical specs cover a robust power distribution unit

with surge protection, mounting provisions, and mechanical structure with in-house design (MS/Aluminum extrusion and

powder-coated brackets). Additional requirements include submission of SLD, structural drawings, data sheets, toll-free

support number, escalation matrix, product samples, and assurance of the OEM not being blacklisted or from countries

sharing a land border with India. Approved makes are Barco, NEC, and Delta only, and the offered solution must support

software features like auto source detection, layout management, scheduler, live preview, multi-level authentication,

integration capability, and IPAD management, all with scalable architecture and protection against unauthorized use.

2 Processor Video Processor 8x8 Delta/NEC/Barco 1 ₹ 2,500,000.00 ₹ 2,500,000.00

Supply, Installation, testing and commissioning of Ceiling microphone with automatic dynamic Beamforming technology,

The beam will automatically detect the position of the person speaking and will follow the person around the room at all

times. It should have 2 x Dante digital audio (Redundancy), Analog audio out (Phoenix 3-pin), and Ethernet for Control and

PoE connectivity ports. The coverage of the ceiling microphone should be min 800 square feet or more. It should have a

Ceiling true voice lift feature to increase audio intelligibility above the ambient noise floor. It should support IT industry

3 Sennheiser/Shure/Televic 2 ₹ 689,570.00 ₹ 1,379,140.00

microphone standards like IEEE 802.1x. It can be controlled through software that can control and monitor the microphone in any

network. It should have min 100 dB SPL, 5ms latency, and min 90dBA or higher dynamic range. High-precision audio

settings for maximum control, setting to exclude (min 5) and prioritize the areas of the room. It should certified from

Microsoft Teams and Zoom Video conferencing applications. It should have UL 62368 certification (including UL 2043

testing and compliance) and safety certifications.

Suppy Installation Testing and Commissioning of digital signal processor with minimum 12no. Or more Mic / line input

with phantom power and AEC and 8 or more line level output, 1no. Or more GPIO at least 2 channel of USB input and

Digital Signal output for software Video Conferencing, should have 8x8 channel of digital dante input output, Should have sampline

4 Xilica/Biamp/AV Space 1 ₹ 875,700.00 ₹ 875,700.00

Processor rate of 48kHz or better, Should be expandable for port expansion, should support Control with App via iOS and Android

devices, or any third-party control system, Shall have Built-in filters, feedback suppression, AGC single-device(chassis) use

is permitted, but the combination of devices is not accepted etc complete as required as per specifications

Supply, Installation, testing and commissioning of 8 channel energy star rated digital power amplifier,8 channel at 4 Ohm

or 8 ohm energy-efficient amplifier - 8 x 30W or more at 70/100V Technology : Class-D,Input linking through miniature

5 Amplifier Biamp/Audac/Bose 1 ₹ 335,500.00 ₹ 335,500.00

switches, Switching mode power supply, Protection : DC Short circuit & Over heating & Over load & Signal limiting,

Frequency Response 120 Hz - 20 kHz or better, Silent passive cooling etc complete required as per specifications.

Supply, Installation, testing and commissioning of 6.5" two-way coaxial thin edge ceiling loudspeaker having 100V

transformer power taps from 60watts to 15watts or better it should have metal back can for premium performance in

6 Ceiling Speakers demanding applications, Conical dispersion : 142° or more, Low impedance RMS continuous power of 60watts, Biamp/Audac/Bose 4 ₹ 38,570.00 ₹ 154,280.00

impedance : 8 or less,frequency range (-10dB) : 70 Hz - 20 kHz, frequency response (±3dB) : 100Hz - 20KHz, Max SPL on

100v should be 105dB or more etc complete required as per specifications.

Digitally signed by AMIT

S.No. Item Specifications Makes Qty Unit Price Total Price

Supply Installation Testing and Commissioning of Full HD 1080p @ 60 frames per second PTZ Camera with minimum 20X

Optical Zoom and FoV of minimum 57 deg, min 100 Presets.Camera should support simultaneous outputs through

Ethernet, HDMI, 3G-SDI, Audio In and can be controlled via RS232 & 422 In & Out & IP.Panning angle -170° ~ +170°, Tilting Lumens/

angle -30° ~ +90° . The tilting and panning speed of camera should be minimum 300° per second. Camera should support PTZ Optics/ Vaddio

SRT, FreeD Protocol, PoE and Virtual USB Driver. OEM should be CE, FCC, RoHS & BIS Certified with test lab report

supporting the certifications.

Supply, Installation, Testing & Commissioning of Processor which can enable Voice Tracking through PTZ Cameras

integrated with Ceiling Tiles on IP. The Processor should be capable of connecting minimum 4x Ceiling Tiles with 4x IP Lumens/

based PTZ Cameras for Quadview output and Auto Switching . The processor should have USB 3.0 Output for Soft VC. PTZ Optics/ Vaddio

Quoted model should be BIS, CE, FCC & RoHS Certified with Test Lab Reports.

Supply Installation Testing and Commissioning of surface-mount USB-to-Dante endpoint, two-way volume and mute sync

for Microsoft Teams,compliant with CE and FCC, device shouold have Power-over-Ethernet (PoE) to IEEE 802.3af Class 0

USB to Dante standard and support Dante networking using standard CatX cable, device should support the Speakerphone profile with

9 Xilica/Audac/Symetrix 1 ₹ 195,500.00 ₹ 195,500.00

Device and without echo cancellation, enable two-way volume and mute syncronization with both PC and Mac platforms, Dante

with AES67 compliance,Sampling Rate(s) 48 kHz,should be from same OEM as DSP etc complete required as per

specifications.

Suppy Installation Testing and Commissioning of control system with touch panel/Ipad, 100/1000 Mbps, auto-switching,

Apple/Crestron/Extron/Cypress/

10 Touch Controller auto-negotiating, auto-discovery, full/half duplex, industry-standard TCP/IP stack, UDP/IP, CIP, DHCP, SSL, TLS, SSH, SFTP 1 ₹ 545,000.00 ₹ 545,000.00

(SSH File Transfer Protocol), FIPS 140-2 compliant encryption

11 Switch Supply, Installation, testing and commissioning of 16 port switch Netgear/Dlink/Cisco 1 ₹ 135,000.00 ₹ 135,000.00

Supply, Installation, testing and commissioning of HDMI RX extender with complies with the advanced HDCP 2.2 and

HDMI 2.0 standards, uncompressed HD audio and video as well as control via a single run of Cat.5e/6/7 cable over

12 TX distances of up to 70 meters and upto 40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 Crestron/Extron/Cypress 8 ₹ 55,750.00 ₹ 446,000.00

pass-through) and CEC bypass, Supports pass-through of many audio formats including LPCM (up to 8 channels),

Bitstream and HD Bitstream

Supply, Installation, testing and commissioning of HDMI TX extender complies with the advanced HDCP 2.2 and HDMI 2.0

standards, uncompressed HD audio and video as well as control via a single run of Cat.5e/6/7 cable over distances of up

13 RX to 70 meters and upto 40mat 4K, HDBaseT feature support: HD Video and Audio, and Control (IR/RS-232 pass-through) Crestron/Extron/Cypress 8 ₹ 55,750.00 ₹ 446,000.00

and CEC bypass, Supports pass-through of many audio formats including LPCM (up to 8 channels), Bitstream and HD

14 Cable cubby Supply, Installation, testing and commissioning of Cable cubby (1 HDMI, 1LAN,1 Charging socket) Logic/AV Space/Custom 1 ₹ 55,700.00 ₹ 55,700.00

Supply Installation Testing and Commissioning of HDMI Audio Extractor should extract up to 2 channels of LPCM audio or

5.1 channels of Bitstream audio from an HDMI source, allowing the user to convert high quality HDMI audio into more

convenient analog (LPCM 2.0 sources only) or optical signals for use with powered speakers or non-HDMI AV receivers.

HDMI Both the input and output HDMI ports should support 4K UHD resolutions up to 4K@60Hz (4:4:4, 8-bit) and should

15 Crestron/Extron/Cypress 1 ₹ 93,100.00 ₹ 93,100.00

Deembedder capable of providing high quality audio and video performance. The unit should supports passthrough of HD and standard

Bitstream formats as well as LPCM 7.1 with audio sampling rates up to 192kHz. Built-in EDID management support allows

the user select from multiple EDIDs and, with the use of optional PC software, to upload, download, or edit EDID files etc

and complete as required

Supply, installation, testing and commissioning of USB peripheral switch which should be a 4x4 industrial USB 3.2 Gen 1

hub switch that enables four computers to share up to four USB 3.2 Gen 1 peripheral devices such as keyboard, mouse,

and other USB equipment. The switch should support SuperSpeed data transfer rates up to 5 Gbps, be compatible with

Windows, Mac, and Linux platforms, and allow port selection via front panel pushbutton, external remote controller, or

16 USB switcher Extron/Cypress/Crestron/Aten 1 ₹ 85,750.00 ₹ 85,750.00

RS-422/RS-485 link through a 5-pin terminal block. The device should feature four USB Type-B ports for computer

connections and four USB Type-A ports for peripheral devices, with support for USB BC 1.2 battery charging and

overcurrent protection. The unit must offer hot plugging, power-on detection with automatic focus switching, and display

port focus via LED indicators. It should be housed in a robust metal chassis with wall and rack mount options

Supply, Installation, Testing & Commissioning of USB 3.2 Extenders. Transmitter should have 1xUSB C input port, 1X RJ45,

1xUSB-A Output Port. Receiver should have Input Port 1×Cat5e/6A/7 (RJ45). 1×USB-C, 3×USB-A Output Port. Bandwidth

17 USB Tx Rx Extron/Cypress/Crestron 1 ₹ 96,000.00 ₹ 96,000.00

upto 5Gbps (SuperSpeed), Tranmission distance upto 100M. Devices should be controlable by the USB host on a

transmitter. Should have backward compatibility with USB 2.0

Digitally signed by AMIT

S.No. Item Specifications Makes Qty Unit Price Total Price

18 Cables Cables & connectors Falcon/AV Craft/Logic 1 ₹ 150,000.00 ₹ 150,000.00

SITC of All-in-One PC, Intel Core Ultra 7 155U, 27inch (68.6 cm), FHD,IPS,Three-Sided Micro-Edge, Anti-Glare,300 nits,16

GB DDR5,1TB SSD,Windows 11,MSO21,Shell White,6.72kg,27-cr1007in 0r Higher.

Digitally signed by AMIT

S. No. Item Description Make Unit Qty Rate Amoint

Supply, installation, testing, and commissioning of smart-managed

network switch, which should have the following features or better: 48 RJ-

45 auto sensing 10/100/1000 Mbps Gigabit Ethernet ports (IEEE 802.3

Type 10BASE-T, IEEE 802.3u Type 100BASE-TX, IEEE 802.3ab Type

1000BASE-T, or better), 4 SFP/SFP+ uplink ports supporting 1/10GbE fiber

transceivers (or better), a switching capacity of 176 Gbps or more, and a

forwarding rate of 130.95 Mpps or higher. The switch must utilize an ARM

Cortex-A9 processor at 800 MHz or faster, with at least 512 MB SDRAM

and 256 MB flash memory, and a packet buffer of 1.5 MB or more. It

3 48 Port L2 Switch Aruba/Juniper/Arista Nos 1 ₹ 297,000.00 ₹ 297,000.00

should support Layer 2+ features, including VLANs (minimum 256 or

more), link aggregation, Spanning Tree Protocol, IGMP snooping, Quality

of Service (QoS), port mirroring, rate limiting, auto MDI/MDI-X, and

advanced security features such as IEEE 802.1X authentication, ACLs, and

automatic denial-of-service (DoS) protection. The unit should offer web-

based, cloud, and SNMP management, with support for management via

Aruba Instant On portal, mobile app, or local web GUI, and provide

multiple privilege levels with password protection. The MAC address table

should support at least 16,000 entries or more. The switch must be rack-

Supply, (1U formtesting,

installation, factor) and commissioning of smart-managed

network switch, which should have the following features or better: 48 RJ-

45 auto sensing 10/100/1000 Mbps Gigabit Ethernet ports, a PoE+ power

budget of 270 W, (IEEE 802.3 Type 10BASE-T, IEEE 802.3u Type 100BASE-

TX, IEEE 802.3ab Type 1000BASE-T, or better), 4 SFP/SFP+ uplink ports

supporting 1/10GbE fiber transceivers (or better), a switching capacity of

176 Gbps or more, and a forwarding rate of 130.95 Mpps or higher. The

switch must utilize an ARM Cortex-A9 processor at 800 MHz or faster, with

at least 512 MB SDRAM and 256 MB flash memory, and a packet buffer of

3 48 Port POE Switch 1.5 MB or more. It should support Layer 2+ features, including VLANs Aruba/Juniper/Arista Nos 1 ₹ 455,720.00 ₹ 455,720.00

(minimum 256 or more), link aggregation, Spanning Tree Protocol, IGMP

snooping, Quality of Service (QoS), port mirroring, rate limiting, auto

MDI/MDI-X, and advanced security features such as IEEE 802.1X

authentication, ACLs, and automatic denial-of-service (DoS) protection.

The unit should offer web-based, cloud, and SNMP management, with

support for management via Aruba Instant On portal, mobile app, or local

web GUI, and provide multiple privilege levels with password protection.

The MAC address table should support at least 16,000 entries or more.

The switch must be rack-mountable (1U form factor)

Digitally signed by AMIT