Spl repair to bldg No.160 (single offrs accn), improvement of parking area main bldg, addn/altn to bldg No. 372 and Provn of hard standing with concrete pedestal for installation of MIG 27 Aircraft at FCBRNP at CME Pune

Amount

Taking down cement plaster any description from roof slab, stone wall, brick wall parapets including raking out joints, hacking for key scrubbing down with water etc. (for roof treatment) all as specified and directed.

M & L rendering 15mm thick on stone masonry surfaces in CM 1:6 finished even and smooth (without using extra cement) with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M & L rendering 5mm thick on concrete surfaces in CM 1:3 on ceiling, finished even and smooth (without using extra cement) with sagol complete all as specified and directed.

M & L for preparation of newly plastered surfaces of wall, applying 3mm POP/Birla wall care putty and applying two coats of oil bound distemper over one coat of primer on walls complete all as specified and directed.

M & L for preparation of newly plastered surfaces of ceiling and applying complete ceiling with 3mm POP/Birla putty for making smooth surface and applying three coats of white wash complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Dimolition of cement concrete (unreinforced) in floors and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M & L for cement concrete type B-1, 1:2:4 (20mm graded stone aggregate) in floors 25mm thick complete all as specified and directed.

M & L for 75mm thick PCC type D-2 (1:4:8) using 20mm graded stone aggregate) as in sub base etc complete all as specified and directed.

M & L light shade vitrified ceramic tiles 10mm thick (square/rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

All as per item No. 10 above, but in skirting over 10mm thick CM 1:4 backing layer complete all as specified and directed.

Dismantling of wall and ceiling boards (fibre, pulp, insulation boards/ slabs/ blankets) any thickness, including cover fillets complete all as specified and directed.

M & L in repair 4mm thick asbestos cement plain building boards, fixed to timber framework in ceiling/ wall/ sunshades with screws/ nailing complete all as specified and directed.

M & L for 2nd class hard wood plain fillets, square, rectangular or triangular in section, clean sawn, secured with nails or brads (sectional area exc. 13 sq.cm & n. exc. 25 sq. cm) as in studs of ceiling/ sunshade complete all as specified and directed.

All as per item No. 14 above, but (sectional area exc. 6 sqcm & n. exc. 13 sq. cm) as in forking pieces in ceiling/ mosquito proofing frames.

All as per item No. 14 above, but sectional area exc. 3 sq.cm & n. exc. 6 sq. cm for fixing etc all as specified and directed.

Demolition of stone/ block/ boulder masonry, built in cement mortar or cement lime mortar including all quoins, arches, pillars etc. or concrete surface etc complete all as specified and directed.

M & L for precast plain cement concrete solid block/ stone masonry type C-1, 1:3:6 using 20mm graded stone aggregate built in CM 1:6 complete all as specified and directed.

M & L for complete removal of old surfaces of wood and wood based surfaces and applying two coats of synthetic enamel paint over one coat of pink primer on surfaces of wood of any description over 10cm in width or girth complete all as specified and directed.

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. complete all as specified and directed.

M & L for 75mm thick PCC 1:3:6 type C-2, (using 40mm graded stone aggregate) as in sub base of floor all as specified and directed.

M & L for 100mm thick PCC 1:2:4 type B-2, (using 20mm graded stone aggregate) as in floor finish surface including broom finish etc. complete all as specified and directed.

Forming contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound grade 'A' etc complete all as specified and directed.

M & L for providing & fixing 12mm thick gypsum board in ceiling (two or three stages if required) including GI U-section 50mmx35x7mm & edge side GI U-section size 30mmx15mmx7mm fixed with screw gypsum board and frame suspended with soffit cleat to roof for hanging 4mm dia GI hanger rod with adjustable level clips, after fixing of gypsum board joints/junction of gypsum board ceiling to be covered with 50mm to 100mm corner strips, rounds at fan & lights, cut for cassette AC indoor unit and light complete all as specified and as per manufacture's instruction and applying two coats of luster paint over 3mm POP to visible side of gypsum board ceiling shade/tint complete all as specified and directed by Engr-in-charge.

Dismantling wrought iron or mild steel work, viz. mild steel flat iron, mild steel bars, bends, straps and similar work including mild steel bolts, nuts etc.., fixing to RCC fencing posts, struts etc. all as specified and directed.

S & F framed work such as roof trussed (framed), trussed purlins, crane gantries, rails and fastenings and heavy bracket framing (beam, tee, angle, channel or flat sections) including distance pieces, cleats, bolts etc. Fe-410-W (Gde E-250) quality A complete all as specified and directed.

M & L for preparing the new surfaces of steel surfaces of any description, over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over one coat of redoxide zinc chrome primer all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding, to wall, fixed with self tapping screws as specified including dismantling complete all as specified and directed.

S & F prepainted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding ridge and boarding to wall, fixed with self tapping screws as specified including dismantling complete all as specified and directed.

Dismantling boarding any description in any position with nails complete all as specified and directed.

M & L cutting hole in brick walls/stone walls (exc. 150 sq.cm but n. exc. 400 sq.cm) for any purpose and making dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required complete all as specified and directed by Engineer-in-Chage.

M & L for PCC 1:3:6 type C-2 using 40mm graded stone aggregate as in, plinth protection 75mm thick including necessary use and waste of form work complete all as specified and directed.

M & L for rendering 15mm thick face of masonry/concrete surface in CM 1:4 finished even and smooth (without using extra cement) over and including 10mm thick dubbing coat in CM 1:4 complete all as specified and directed.

M & L for preparing newly plastered surfaces of wall and making smooth surfaces and applying two coats of cement based paint as per manufactured instruction complete all as specified and directed.

M & L for complete removal of existing treament of old plastered surfaces of wall and applying complete wall with POP/Birla putty and making smooth surfaces and applying two coats of Oil bound distemper over a coat of primer all as specified and directed.

M & L for preparing of old plastered surfaces of wall and making smooth surfaces and applying one coats of cement based paint over a coat of primer all as specified and directed.

M & L for PCC (1:2:4) type B-1, using 20mm graded stone aggregate as in coping, bands, plinth courses, parapets etc like including weathering, slightly rounded or chamfered throating complete all as specified and directed.

Surface excavation n. exc. 30cm deep and averaging 15cm deep and getting out in hard/dense soil complete all as specified and directed.

M & L moorum/red bajri filling in floors or pavings, laid in layers n. exc. 15cm thick, spread, levelled and rammed including watering complete all as specified and directed.

M & L hardcore using broken stone or boulders not exceeding 63mm deposited spread and levelling in layers not exceeding 15cm thick watered and rammed to a true surfaces complete all as specified and directed.

M & L 100mm thick PCC 1:3:6, type C-2 (using 40mm graded stone aggregate) as in hardstanding and finished even and fair without using extra cement complete all as specified and directed.

M & L rendering 15mm thick on stone/block masonry surface in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed by Enr-in-Charge.

Removing excavated material (soil) n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified & directed.

Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth for foundation etc., or for shafts, wells, cesspits, manholes, pier holes, etc. n. exc.10 sq m on plan and n. exc. 1.5 m in depth and getting out in hard/dense soil all as specified and dierected by Engr-in-charge

Excavating in trenches n. exc. 1.5 m wide and n. exc. 1.5 m in depth for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in soft/disintegrated soil all as specified and dierected by Engr-in-charge

M&L for PCC 1:3:6 Type C -2 using 40 mm graded crushed stone aggregate as in foundation,filling and mass concrete complete all as specified & directed.

M&L for Reinforced cement concrete (nominal mix) in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc. basement slabs, under-reamed piles and mass concrete Type B1 1:2:4 using 20 mm graded crushed stone aggregate complete all as specified & directed.

M&L for formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams and similar work, vertical or to batter complete all as specified and directed.

S&F steel work in Joist, channel, angle, or tee sections,fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) complete all as specified and directed.

S&F Fe-410-W (Gde E-250) Quality B mild steel plates, plain or chequered, 12 mm thick or over in thickness in available sizes complete all as specified & directed.

S&F Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and directed.

M&L for Granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry over 20mm thick screed bed in CM 1:6 and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

M&L for 20mm thick Granite (of any type) tiles machine cut, in skirting/dado laid over cement screed and jointed with grey cement slurry including 12 mm thick rendering in CM 1:4, and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified and directed

Taking down carefully copper/aluminium point wiring (light, fan, bell, socket or power) complete including fixture and fittings such as switches, ceiling rose, pendents, regulators, sockets, light fittings etc removing materials to store for keeping in safe custody or for takig credit and making good disturbed surfaces of walls, floors etc. credit for above items should be made as per conditions separately.

M & L for point wiring for light/fan/bell with FRLSH cable 1.5 Sqmm PVC insulated (red for phase and black for neutral) unsheathed, multi stranded copper conductor 1100 volt grade in and incl not less than 2mm thick PVC casing/capping with all accessories and 1.50 sqmm green in colour PVC copper conductor cable for earth contiuity connected to common earth dolly incl PVC box surface/flush type with PVC sheet for mounting fittings such as switches, fan regulators, etc. complete all as specified and directed for one light/fan/bell point controlled by one switch & making good to disturbed surface of wall etc.

One light point controlled by one switch

One fan/exhaust fan point controlled by one switch and regulator

Socket outlet, three pin 5 Amps on the same board

Socket outlet, three pin 5 Amps, independent

All as per item No. 55 above, but with 2.5 sqmm cable and 2.5 sqmm for earth continuity multipin 15 Amps socket outlet flush type on independent board.

S & F switch piano, flush type, single pole one way 5 Amps complete all as specified and directed.

S & F switch piano, flush type, single pole one way 15 Amps complete all as specified and directed.

S & F bell push flush type single pole one way 5 Amps complete all as specified and directed.

S & F socket outlet 2 in 1, 5 pin, 5 Amps flush type complete all as specified and directed.

S & F socket outlet 5 in 1, 5 pin, 15 Amps flush type complete all as specified and directed.

S & F switch socket combination 5 in 1, 5 pin, 5 and 15 Amps flush type complete all as specified and directed.

S & F ceiling rose, PVC/Polycarbonate isolated body, surface bakelite 65mmx50mm, 3 terminal incl PVC square block complete all as specified and directed.

S & F stepped type electronic fan regulator flush type on the existing phenolic laminated sheet complete all as specified and directed.

S & F Call bell ding dong AC, 230 Volts, single pole complete all as specified and directed.

S & F surface and wall mounted LED batten (LED tube light fitting 20W) with polycarbonate housing & integrated electronic driver alongwith LED tube 20 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting. Make : Havells cat No. LUMILINEBS20WLED830SPCWH or equivalent of Philips/ Bajaj/ Shakti

S & F surface and wall mounted LED batten (LED tube light fitting 10W) with polycarbonate housing & integrated electronic driver alongwith LED tube 10 watt and 02 Nos PVC square blocks incl taking down old UNSV fitting. Make : Havells cat No. LHEXACP7INW010 or equivalent of Philips/ Bajaj/ Shakti

S & F building security LED light fitting 25 Watt, energy saving and environmental friendly long life LED fitting made up of pressure die cast aluminium housing with acrylic cover as diffuser with IP 66 protection and impact resistance of IK 07 including suitable size bracket incl taking down old UNSV one. Make : Havells cat No. ENDURAPEARLSL25WLED757SASYTOPC or equivalent of Philips/ Bajaj/ Shakti

M & L for sub main wiring with two run of 6 sqmm single core multi stranded PVC insulated and unsheathed copper conductor (red for phase and black for neutral) of grade 1100 Vol FRLSH cable in and including 1100 Volt electrical grade PVC casing capping of desired colour not less than 1.2mm thick and 25mm wide & 10 Sqmm copper conductor cable PVC unsheathed green coloured for earthing with complete accessories duly connected with earth dolly complete all as specified and directed incl taking down old unserviceable one.

S & F in replacement enclosure, single pole and neutral enclosure with a two pin and earth plug and socket complete with one single pole MCB 20 Amps, 240 volt complete all as specified and directed.

S & F in replacement MCB distribution board double door SPN 240 volts 8 way with 200 Amps rated bus bar and making good to disturbed surfaces of floors walls etc. complete all as specified and directed.

S & F in replacement MCB distribution board double door 240 volts 4 way with 200 Amps rated bus bar and making good to disturbed surfaces of floors walls etc complete all as specified and directed.

M & L in replacement MCB distribution board double door 415 volt, TPN 4 way complete all as specified and directed.

S & F in replacement MCB TPN 100 Amps, 415 Volt, AC complete all as specified and directed.

S & F in replacement MCB SP 6 to 32 Amps, 230 Volt, AC complete all as specified and directed.

S & F in replacement MCB TPN 63 Amps, 230 V, AC complete all as specified and directed.

S & F in replacement MCB TPN 40 Amps, 230 V, AC complete all as specified and directed.

M & L for earthing complete with GI earth plate electrode of size 60x60x0.6 cms thick burried directly in ground vertically at a depth of not less than 2.25 mt below normal ground level with top edge of the earth plate not less than 1.5 mt deep below normal ground level connected to galvanised iron strip of 25mmx4mm as earthing lead by means of nuts, bolts and washers of steel after welding of GI strip to earth electrode to the full length of earth plate, 40mm dia GI tubing light grade protection pipe upto test point, 20mm dia GI watering pipe with funnel and wire mesh,PCC pit 1:3:6 with pit cover of size 30x30 cm made of RCC 1:3:6 with suitable handle, angle iron frame of angle iron size 40mmx40mmx40mm, adequate qty of charcoal dust and salt layers all around the earth plate, removal of surplus soil and returning filling in all as required at site all as specified in electrical plate No. 3 of SSR Part-I and directed by Engr-in-Charge.

Supply & fix energy saving recess mounted luminairs high translucent defuser gives soft glare free light 36W suitable for 600mm x 600mm Modular/POP/Gypsum ceiling 5700 K of cat No. LCPL-36-CDL . Make:- Crompton or equivalent in Havells/Philips

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated cable with stranded copper conductor of size 1.5 Sq.mm nominal area and drawing, in PVC casing caping including PVC insulated 1.5 Sqmm (nonimal area) stranded copper conductor earth wire complete. Note :- Two runs of 1.5 sqmm cable, one run of 1.5 sqmm earth wire cable and one run PVC casing caping will be measured as one unit.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated cable with stranded copper conductor of size 4 Sq.mm nominal area and drawing, in PVC casing caping including PVC insulated 4 Sqmm (nonimal area) stranded copper conductor earth wire complete. Note :- Two runs of 4 sqmm cable, one run of 4 sqmm earth wire cable and one run PVC casing capping will be measured as one unit.

Supply & fix DB 6 way SPN with 200 Amps rated bus bar, double door including wooden box suitable size. Make :- Indoasian/ Schneider/ Siemens

Supply & fixing of MCB single pole and neutral rating capacity 40 Amps, 240 V breaking capacity 10 KA C series

Supply & fixing of MCB single pole and neutral rating capacity 6 to 32 Amps, 240 V breaking capacity 9 KA C series

Excavation in trenches n. exc. 1.5m wide and n exc. 1.5m in depth for laying cables and getting out in soft/loose soil all as specified and directed.

Returning filling in, including, spreading, levelling, watering and well ramming in layers n. exc. 25 cm in soil all as specified and directed.

Supply, laying and testing cable XLPE insulated screened PVC bedded galvanised steel strip or wire armoured, electric power cables (heavy duty) with stranded aluminium conductor 1100 volts grade cross sectional area 2 core 10 Sqmm complete all as specified and directed.

Supply & Laying DWC (Double Wall corrugated) HDPE pipe ISI marked of outer dia of 50 mm and inner dia 38 mm polythylene with smoooth inernal and profiled external surface for non pressure under ground cable incl couplers & bends complete all as specified and directed.

Supply and fixing LED flood light 70 watt 230 V AC outdoor type with thermal management in multiple optics and equipped with IP66 protection, with impact and corrosion resistant complete with driver and lamp incl mounting arrangement.

Supply and fixing or passing through pipe, 1100 volts grade heavy duty , PVC insulated round 3 core 2.5 sqmm copper cable including electrical connection complete all as specified and directed by Engr-in-Charge.

M&L for providing plain cement concrete type D-2 , 1:4:8 (using 40mm graded stone aggregate) in foundation filling and mass concrete all as specified and directed.

Material & labour for earthing complete with galvanized steel earth electrode plate of size 60mmx600mmx6mm thick buried directly in ground/earth pit not less than 2.25 mtr deep below normal ground level and top edge of earth electrode not less than 1.5 mtr below normal ground level and connected with GI earth wire of size 4 mm by means of nut, bolts, washers etc to eqpt/machinery all as shown in electric plate No 3 of SSR Pt I including PCC (1:3:6) pit, pit cover 50mm thick RCC 1:2:4 type B-1 using 8mm tor steel bars @10cm C/C both ways, 20 mm bore medium grade GI protection pipe, watering pipe 20mm bore medium grade, funnel, wire mesh, also including earth work, common salt, charcoal dust complete, including all as specified and as directed by Engineer-in-Charge. (Note:-Earth wire/strip to be secured on bus bar insulators and insulators shall be fixed on pole not more than one meter apart with MS clamps made out of 25x4mm MS flat wth nuts, bolts and washers and GI wire/strip shall be fixed in such a way that wire/strip should not be touch on pole in any case)

M & L for fabrication, supply and installation dust, weather & vermin proof L.T feeder pillar box (approx size 300mm x 250mm x 300mm) outdoor cubicle/KIOSK type totally enclosed outer cage fabricated with 3.15mm thick MS sheet with frame made of MS angle iron 25x25x3 mm suitable for operation on single phase, 230V 50 Hz system, with single panel doors and locking arrangement consisting of sufficient Nos of circular cable entry holes at bottom only with suitable PVC/ rubber/ wooden bushes to prevent ingress of water/ vermin etc, inside the enclosure. All the holes shall be fixed with chromium plated brass cable glands for cable entry/exit with & including necessary internal wiring with stranded PVC insulated FRLS copper conductor cables of adequate size. The kiosk/ box shall be powder coated internally /externally of approved colour. Quoted unit rate shall be deemed inclusive of PCC foundation, angle iron legs & the following accessories:-

MCB SPN 63 Amps - 01 No

MCB SP 10 Amps :- 04

Provision of cubicle to accommodate the above mentioned accessories.

Internal wiring of panel board, metering equipment with suitable size PVC insulated, unsheathed, 1100 V grade cable with multistranded copper conductor, including provision of lugs/thimbles on either ends of cable.

Mukund Engineers and Contractors

BSK Construction