Provn of fire static tank at INS Gomantak, grills and aluminium doors at MNS Officer mess, supporting structure to the existing cantilever at main entrance of INHS Jeevanti and addn altn to hospital lab, dental lab and blood transfusion Dept at INHS

Amount

Demolition of cement concrete (reinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level).

Excavation over area not exc 1.50m deep and getting out in soft/disintegrated rock.

Excavation over areas exceeding 1.5 m deep but not exceeding 3.00 mtr and getting out in soft/disintegrated rock complete all as specified and directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out from soft/disintegrated rock .

Excavation in post holes each not exceeding 0.5 cum getting out returning filling in & ramming earth or broken rubble mixed with earth around in layers not exc, 25cm in soft disintegrated rock.

M & L cement concrete type C1, 1:3:6 (using 20 mm graded aggregate) as in post hole and coping incl necessary form work all as specified and as directed.

M & L cement concrete type B2, 1:2:4 (using 40 mm graded aggregate) in foundation filling and mass concrete all as specified and as directed.

M&L for formwork to sides of pillars, posts, struts and columns and similar works flat and rough finished surface etc.

M&L for formwork to sides of concrete foundations, footings bases of columns plinthbeam and similar works flat and rough finished surface etc.

Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping)

Formwork to sides and soffits of roof beams, beam haunchings, girders, bressummers, including supports, overhangs, etc. also splays between floors and beams, etc.

M&L formwork to faces of retaining wall and similar work including attached pillasters ,buttresses with rough finish complete all as specified

M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete

M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Columns, pillars, piers, posts and struts

Material & Labour for RCC type B-1, 1:2:4 (using 20 mm graded aggregate) set in cement mortar 1:4 as in landings, cover slabs (for drains, man holes etc.) chullah hoods, chajjas, water troughs, mangers, shelves and similar articles with plain faces

M&L for RCC M-40 in foundation including rafts, footing, foundation beams, plinth beams, bases for column etc all as specified and directed.

M& L RCC M-40 in walls, retaining wall, basement walls, ballast walls and the like . Any thickness above top of footing including attached pilaster and buttersses all as specified and directed.

M&L for RCC M-25 (Design Mix) using (20mm graded stone aggregate) as in columns, pillars, posts & struts complete all as specified.

M&L for RCC M-25 (Design Mix) using (20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L for RCC M-25 (Design Mix) using (20mm graded stone aggregate) as in slab supported on walls, beams and columns (Horizontal or sloping) complete all as specified.

Material & Labour for TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking,bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips. Complete.

M&L TMT steel bars 8mm dia, cut length, bent to shape required, including cranking, bending spirally for hooping forcolumns, hooking ends and binding withmild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming to TMT bars.all as specified and as directed.

M&L granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete

Material and labour for cutting chases, pinning in making good to facing where required and pointig in cement moratr 1:3 to ends or edges of landing, steps, cills, sunshades , shelves, lintels, etc;and cutting chases for concealed water tubing or concealed conduit wiring, etc; and making good, cutting not exc 10cm girth all as specified and as directed.

Cutting openings, through brick walls built in CM or cement lime mortar for door, window and other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective brick work for under-pinning, including providing, fixing & removing shoring, cleaning and stacking bricks, removing surplus serviceable bricks, hard-core, etc., to store and rubbish not exc. 50m

Demolition of Brickwork or stone/boulder masonry, built in CM or cement lime mortar including all quions, arches, pillars etc, but excluding ashlar facings, dressed stonework & precast concrete articles

M&L Pre-cast cement concrete block masonry with solid blocks, exc. 10cm in width and setting in mortar CM 1:4,type C1 1:3:6 using 20mm graded aggregate complete

Taking down cement plaster on brick or stone wall etc., including racking out joints, hacking for key, scrubbing down with water, etc complete

Material and labour rendering cement plaster 10 mm thick in CM 1:6 on fair faces of brick/concrete faces (internal walls) finished even and smooth without ung extra cement.

Material & Labour for providing two coats of oil-bound distemper over a coat of alkali-resistand primer on new plastered surfaces including necessary preparation to surfaces complete all as specified and as directed

Material & Labour for providing two coats of oil-bound distemper over a coat of alkali-resistand primer on old plastered surfaces including necessary preparation to surfaces complete all as specified and as directed

Material & Labour for renderuing in CM 1 : 4 (10+5)=15mm thickness on brick/cement/stone surfaces and finishes the surface even and smooth with out using extra cement.

M & L two coats of cement based paint over a coat of alkali resistant primer including preparation of new plastered surfaes.

Demolition of cement concrete (Unreinforced) concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level)

M&L machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L kota stone slab 20-25mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete

M&L 25 mm thick Cement concrete type B-0, 1:2:4 (12.5 mm graded agregate) as sub floor

M&L 15 mm thick screed bed or bedding layer of cemnt mortar 1:4 for laying floor finishes.

M&L for rendering 10mm thick backing coat in CM 1:4 to receive tiles on vertical surfaces of wall

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing rubbish off the premises.

M & L Glazed ceramic tiles in vertical surface 300x200x 7 mm thick set and jointed in neat cement slurry and pointed in white or colour cement to match with colour tiles.

M & L Non-skid coloured ceramic tiles 7 to 8 mm thick area of each tiles exc 0.6 sqm but n exc 0.11 sqm, in floors etc set and jointed in neat cement slurry and pointed in white cement or coloured cement to match

Material & Labour vitrified Ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm light shade, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Taking up or down 20mm steel tubing and connections,fixed to wall /floor

Taking up or down 25 mm steel tubing and connections, fixed to wall /floor

Supplying and laying of 20 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

Supplying and laying of 25 mm dia CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings on walls/ceiling or laying in floors complete all as specified.

S&F sinks made of stainless steel lmm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mm

S & F in repairs Vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste, chain and plug and porcelain stopper but including brackets.

S & F Pillar taps, 15mm dia, cast copper alloy, fancy type with capstan heads, chromium plated, screwed down high pressure, with or without lettered ‘Hot' or ‘Cold' with long screwed shanks and fly-nuts, screwed for iron pipe and fixed in repairs

S & F in repairs Bib taps, 15mm dia, cast copper alloy, fancy type, with capston head, screwed down, screwed for iron pipe or for brass ferrule and fixed in repairs.

S & F in repairs CP stop cock/angle cock 15mm dia, fancy type with capston heads screwed both ends for iron pipe or for unions and fixed

S & F PVC connections 15 mm size with PTMT nuts of length 600m fixed in repair.

S & F in repairs Flush pipe of polyethylene of low or high density or PVC 32 mm dia for low level cistern

M & L 40 mm dia high density polyethylene pipes laid in floor/trenches/ west pipe of wash basin/spout pipe etc. complete all as specified.

M&L Cast iron nahani trap, with steel grating including jointing to waste pipe fixed in cement concrete type B1 (1:2:4)

M & L 2nd class hard wood Plain fillets, square, rectangular or triangular in section exc 6 and n exc 13 Sqcm , clean sawn, secured with mills or brads

M&L 12 mm thick Prelaminatd particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to timber frame work

S&F Continuous (piano) hinges, mild steel, bright finish or electrogalvanised with 40 mm width of flap when open.

S & F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished

S&F Anodised aluminium frame for doors,windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified. Note: frame shall be fixed with 08 Nos 120mm length screw with rawal plug.

S&F 4mm thick sheet glass,ordinary qauality and glazing with oil putty in square exc 05 sqm in each pane

supply and fixing Aluminum powder coated deco grill make DG 104 (10 mm thick section ) with frame of section not less than 0.136 kg/rm

S&F aluminium alloy anodised wire mesh of size 1.5 mm x 3 mm mesh 20 Gauge thick of make M/S Kiran Netting or equivalent as approved by GE.

S & F Anodised aluminium door shutters, aluminium section weighing 0.55kg/m including necessary joining cleats, glazing clips, rubber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminium snap beading, screws etc. complete all as specified

M&L Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty and fixed

Returning filling in including spreading ,levelling , watering and well ramming in layer not exceeding 25 cm thick for soft/disitegrated rock

Removing excavated material n. exc.50 m and depositing where directed at a level n. exc. 1.5 m above the starting point in soft disintigrated rocks

M&L Hardcore broken stone or boulders of gauge exc. 63 mm but n exc 100mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to true surface

Material & Labour for 100 mm thick PCC type C-2, 1:3:6 (using 40 mm graded aggregate), as in sub base of floor. all as specified and directed by Engr in charge.

M&L 50mm thick sand filling under floors or in foundations including watering and consolidation

M&L Machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade with grey cement and pigment all as specified and directed by Engr in charge.

S&F framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes, framed guard bars, and similar work confirming to Fe 290, Grade E-165 complete all as specified and directed.

S&F 4 mm dia gavanised steel wire, 150x100 mm mesh, made up into matteresses or cages, lapped, wired and laid in position, including closing after filling and as directed.

S&F hard drawn steel wire fabric cut to lengths, bent to shape required and tying with and including mild steel wire (aneealed) not less than 0.9 mm in dia and having weight exc 4 kg per sqm.

S & F roof trussed framed, trussed, purlins, crane gantries, rails and fastenings and heavy brackets framing (Beam, tee, angles, channel or flat sections) including distance pieces, cleats etc. (Fe- 410-W (Gde E-250 quality A)

S&F Rolled mild steel Stairs (framed) including stringers, treades, landing, balusters, hand rails etc, including cleats,brackets, etc. complete GDE Fe410-0 or Fe 310-O

M&L for preparation of new steel surfaces and apply two coat of Anti corrossive paint over a coat of anti corresive primer.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covring cladding to wall fixed with self tapping screws as specified .

Supply and laying of 65 mm dia with CPVC Schedule 80 pipes icluding all types of reqd fitting & plain CPVC Schedule 80 fittings & on wall/ ceiling or laying in floor complete all as specified.

Supply and laying of 50 mm dia CPVC pipes SDR 13.5 including all types of reqd fitting & plain CPVC SDR 11 fitting on wall/ ceiling or laying in floor complete all as specified.

Supply and laying GI tubings medium grade dia ISI Mark with all fittings such as elbow, bends, sockets, nipples and union etc and fixed complete laid in trench/wall for the 50 mm dia all as specified and directed by Engr-in-charge.

Excavating in trenches n exe 1.5 m wide and not exceeding 1.5 m in depth getting out hard/dense soil for laying of GI pipe complete includidng taking down of old GI tubing complete all as directed by Engr-in-charge

Excavating in trenches n exe 1.5 m wide and not exceeding 1.5m in depth for removing and laying G.I tubing and getting out in Hard rock.

Returning filling in including spreading, levelling, watering and well ramming in layers n.exc 25cm in hard dense soil completge all as specifiedd and directed by Engineer-in-Charge.

Removing excavated soil to a distance not exc 50 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified and directed by Engineer-in-charge.

Supply and Fixing Gun metal Globe or gate valve with iron wheel head screwed both ends for iron pipe of 50 mm bore sizes complete all as per spd and directed by Engineer-in-charge.

Supply and fix Foot Valve conforming to IS 4038, 65 mm (2.5”) dia complete all as directed by Engr-in-Charge.

Supply and fix Valve, reflux (NRV) 50 mm (2”) dia complete all as directed by Engr-in-Charge.

Supply and Fixing 15 mm ball float valve high pressure of PTMT with expoxy coated alumimium rod and highdensity ball screwed for iron pipe with polythene float and fly nut complete with all accessariess including taking down the old float valve complete all as directed by Engr-in-charge

Supply ,Installation ,Testing & Commissioning of Monoblock pump set suitable for 415 V ,3 phase system having capacity 3 HP (suction 65mm and delivery 50mm,7.9 LPS) including nesssary foundation work ,stud bolts and nuts complete all as directed. Make : Kirloskar Model No KDS 325++ or any other equivalent make approved in MES.

S & F Star Delta starter suitable for three phase Monoblock pump ( Relay range 13-22 A).

S & F 3 core multistranded flat copper cable of 4sqmm for connection of motor to starter motor panel.

Supply and lay cable LT XLPE Insulated screened PVC bedded, galvanized steel strip or wire armored, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10 sq mm 4 core.

Excavation in trenches not exceeding 1.5 m width and not exc 1.5m in depth getting out in hard/dense soil complete all as directed by Engr-in-Charge.

Excavation in tranches not exceeding 1.5 m width and not exc 1.5m in depth getting out soft disintegrated rock complete all as directed by Engr-in-Charge.

M/L for fine river sand for cushioning with layers of sand 8 cm before laying of cable & 15 cm after laying of cable (total 23 cm ) in trenches, duly punning to a thickness of 18 cm for cable protection complete all as directed and specified. Note:-punned down sand thickness will be measured.

Supply and lay PCC cable cover class LV type 1 flat size 250mmx150mmx40mm complete all as directed by Engr-in-Charge.

M & L for GI tubing (light grade) with all fittings,laid in trenches, or fixed along with walls /poles,bore of pipe 40mm.

S & F and installation of Automatic Water Level Controller Model: 3PDA (Auto ON OFF) Including water levels, 0%, 25%, 50%, 75%, 100% Motor Stops above cut off level, Starts below 75% including following items (a) 8 X 4 Channel PLC controller for working of Pumpsas 1 Working 1 Standby. (b) Float Switches 1C x 10 Amp with 3 Meter Cablelength (c) Signal Cable – 7 Core with Rubber Casing complete all as directed. Make Matrix International

M/S DUBAL CONSTRUCTION

SACHIN CONSTRUCTIONS

JINTECH

S S Engineering Works

M/S G.N.POWAR