PROVN OF OPEN SHED AT NARIA and URINAL BLOCK NEAR CLH AND ADDITION/ALTERATION OF BDY WALL WITH PROVN OF FENCING AND CERTAIN REPAIR OF BDY WALL PLASTER AT NARIA AND PROVN OF ALL SANITARY AND ELECTRICAL FITTINGS FOR ECHS POLYCLINIC AT VARANASI CANTT

Amount

Surface excavation in any type of soil not exceeding 30 cm deep and averaging 15cm deep and getting out complete all as specified and directed.

Excavating in trenches, in any type of soil n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out complete all as specified and directed.

M&L for plain cement concrete 1:4:8, type D-2 (using 40 mm graded crushed stone aggregate) as in foundation , filling & mass concrete complete all as specified and directed.

M&L for hard core broken stone of gauge not exceeding 63 mm, deposited spread and levelled in layers not exceeding 15 cm thick, levelling and rammed to a true surface complete all as specified & directed.

M&L for 50mm thick PCC 1:2:4 ,type B1 (using 20mm graded crushed stone aggregate) as in floor finished, complete all as specified and directed.

M&L for Brick work with fly ash old size bricks, straight or curved on plan exceeding 6 m mean radius, built in cement mortar 1:6 complete all as specified and directed.

Returning filling in excavated soil, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each complete all as specified and directed.

Removal of surplus excavated soil to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

M&L for 15mm thick plastering on concrete or other than fair faces of brick wall in CM (1:4) surface finished, fair and even and even complete all as specified and directed.

M&L for applying two coats of cement base paint over a coat of primer including preparation of newly plastered surfaces of walls complete all as specified and directed.

M&L for PCC 1:2:4, type B-0 (using 12.5mm graded crushed stone aggregate) as in coping including necessary form work and finishing complete all as specified and directed.

M&L for 75mm thick Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in levelling course, for floor benching etc, finished even & rough to receive cement mortar screed bed complete all as specified and directed.

M&L for Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 80 mm thickness M-40 Grade and with grey cement and pigment including 25mm thick sand cushning complete all as specified and directed.

M&L for Plain cement concrete type B0 1:2:4 (using 12.5mm graded crushed stone aggregate) as in mud stops, rounded or benching, chamfered on edges and misc surfaces complete all as specified and directed.

S&F Pre- painted galvalum aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for mild steel work as in roof trusses (framed), trussed, purlins, crane gantries, pillars, rails and fastenings and heavy bracket framing (beam, tee, angle, channel, Hollow or flat sections) including distance pieces, cleats etc. Fe 410-W (Gde - E-250) quality - A complete all as specified and directed.

S&F Mild steel screw bolts diameter of neck in 16 to 20mm (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5cm but n exc 10cm long complete all as specified and directed.

M&L for apply two coats of synthetic enamel paint over a coat of red oxide primer including preparation of new surfaces of steel over 10 cm width or girth complete all as specified & as directed

Demolition of brick work built in cement or cement lime mortar complete all as specified and directed.

M&L for brick work with fly ash sub class ‘B’ bricks, straight or curved on plan to any radius in half brick thick walls, built in built in CM 1:4 complete all as specified and directed.

M&L for plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in parapets and railings (up to 60 cm in height), copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded, or chamfered angles and throating, as directed complete all as specified and directed.

M&L for mild steel work as in posts and struts in fencing and iron gate, including cutting tops to shape as directed welding ,drilled holes noting for wire etc including all necessary drilling etc & similar work conforming to Fe - 290 Gde E-165 complete all as specified and directed.

S&F Galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2mm dia barbs at 75 mm spacing and straining and fixing to any type of std rails straining bolts incl securing or tying at crossing with and provision of galvanised MS wire or steel pins etc as directed (each line wire to be measured) complete all as specified and directed.

S&F concertina coil 600mm round dia (at stretched position) made with hot dipped galvanised steel wire coated with CLR anti-corrosive paint (dia of steel wire shall not be less than 3mm), making diamond shape with the help of dovetailed clips having 18 SWG sheet fixed over razor wire medium barbs, concertina coil to be fixed with razor wire at points wherever coil touched the bottom of razor wire with the help of hog rings 14 SWG including all fittings & fasteners clips, steel lugs rings complete all as specified & directed. Note - (i) Stretch length of each coil shall be 6 RM. (ii) Angle iron shall be measured & Paid separately. (iii) Hogging shall be fixed at interval of 600mm centre wherever it touches with razor wire. (iv) Over lapping of coil and razor wire shall be 300mm. (v) Suitable number of razor wire shall be fixed along the length of concertina coil.

Taking down cement or cement lime plaster, any description, on brick or stone walls, etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces, finished fair and even complete all as specified and directed.

M&L for complete removal of existing treatment from walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depressions of scrapped surfaces with 1mm thick wall care putty to make the scraped surface smooth and applying two coats of cement base paint complete all as specified and directed.

M&L reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregate) as in foundation beams, plinth beams, bases for columns complete all as specified and directed.

M&L reinforced cement concrete design mix M-25 (using 20 mm graded crushed stone aggregate) as in columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for reinforced cement concrete (Design mix), M-25 grade, (using 20 mm graded crushed stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for reinforced cement concrete (Design mix), M-25 grade (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves complete all as specified and directed.

M&L for mild steel TMT bars 10 mm dia & over cut to length bent to shape required including cranking bending, spirally for hooking for columns hooking and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

M&L for mild steel TMT bars 8 mm dia cut to length bent to shape required including cranking bending, spirally for hooking for columns hooking and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

M&L mild steel TMT bars 8 mm dia cut to length bent to shape required including cranking bending, spirally for hooking as in stirrups and binding with including mild steel annealed wire not less than 0.9 mm dia securing with clips complete all as specified and directed.

Use and waste form work in flat surfaces to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work complete all as specified and directed.

Use and waste form work in flat surfaces to sides of pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for Use and waste of form work in flat surfaces to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, complete all as specified and directed.

M&L for Use and waste of form work in flat surfaces to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed.

M&L for 25mm thick PCC 1:2:4, Type B-0 ( using 12.5mm graded stone aggregate)as in damp proof course to horizontal or vertical surfaces including necessary formwork complete all as specified and directed.

M&L for 5mm thick plastering on ceiling in CM (1:3) surface finished, even and fair complete all as specified and directed.

S&F factory made uPVC door frame made of uPVC. extruded sections having an overall dimension (extruded section profile) 42x50 mm (tolerance ± 1 mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete all as specified by the manufacturer and as per directions of Engineer-in-charge

S&F 30 mm thick factory made UPVC door shutter made of styles and rails of a UPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and jointed at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickens. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm ( + 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats. The shutter frame filled with a uPVC multi chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness. The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as specified by the manufacturer and as per directions of Engineering- charge.

S&F 150 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

S&F 150 mm size aluminium anodised handles, cast type complete all as specified and directed.

S&F 100 mm size butt hinges, medium weight extruded stainless steel hinge pin, bright complete all as specified and directed.

S&F Aluminium alloy, anodised, sliding door bolt 250 mm long, with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts & sliding bolts of extruded sections or cast aluminium alloy complete all as specified and directed.

S&F Steel ventilator with top hung shutter including hinges, steel peg stay, complete all as specified and directed.

M&L for mild steel framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work con- forming to Fe.290.Gde-E-165 complete all as specified and directed.

M&L for 3mm thick sheet glass ordinary quality and glazing with oil putty in square n exc. 0.5 Sqm in each pane complete and all as specified and directed

M&L for 75mm thick plain cement concrete 1:3:6, type C-2,(using 40mm graded aggregate) as in plinth protection/path/hard standing, finished surface even and smooth without using extra cement complete all as specified and directed

M&L plain cement concrete type C-2, 1:3:6 using 40mm graded aggregate as in surface channel and drain complete all as specified and directed.

M&L for 75mm thick plain cement concrete 1:3:6, type C-2 (using 40 mm graded crushed stone aggregate) as in sub base under floors complete all as specified and directed.

M&L for joint free non skid ceramic white tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sq m but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L for glazed ceramic coloured tiles of size 350x 250x 7 mm/ 450x 300X 7mm thick, as in vertical surface such as skirting, dados, risers to steps, etc set and jointed in neat cement slurry and pointed in coloured cement to match tiles, over and including 10 mm thick rendering in cement mortar 1:4 complete all as specified and directed.

M&L for 25-28 mm thick machine pressed designer [chequered] cement concrete paving tiles [of size 300x300 mm] having wear resistance coating or wear proof topping, tile fixed with @ 3 Kg cement slurry laid over and including 15 mm thick screed bed or bedding layer in cement sand mortar in 1:6 complete all as specified & directed.

S&F 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors complete all as specified and directed.

S&F 75 mm PVC (SWR) pipes single socketed, in any length with rubber ring joints, fixed in wall floor etc. complete all as specified and directed.

S&F PVC (SWR) vent cowl 75 mm , complete all as specified and directed.

M&L for concrete bed to drain pipes 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested in plain cement concrete 1:3:6, type C-2( using 40 mm graded crushed stone aggregate ) complete all as specified and directed.

M&L for salt glazed stoneware drain pipes 150 mm bore, grade ‘A’, laid in trenches and jointed in cement mortar 1:1 and tested complete all as specified and directed.

M&L for cutting into existing manholes for 150mm pipe connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required complete all as specified and directed.

M&L for precast cement concrete type B1, 1:2:4 (using 20 mm graded crushed stone aggregate ) as in man hole cover set in CM 1:6 complete all as specified and directed.

S&F 110 mm PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls and floor etc. complete all as specified and directed.

S&F 15 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings, fixed to walls or laid in floors in any length complete all as specified & as directed.

S&F 20 mm bore galvanised steel water tubing medium grade for water supply pipes & connections with all fittings, fixed to walls or laid in floors in any length complete all as specified & as directed.

S&F 500 Litre capacity rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), double layered (ISI marked) hoisted and fixed in position including necessary connections to inlet / outlet & wash out pipes, complete as specified in SSR Part-I & as directed.

S&F in position 20 mm bore gun metal gate valve with iron wheel head screwed both ends complete all as specified & directed.

S&F stainless steel soap dish as per sample kept in Engineer-in-charge office complete all as specified and directed.

S&F 20 mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod &high-density plastic ball screwed for iron pipe and fixed. (Minimum weight 2 0 m m - 2 1 0 g m s ) complete all as specified & directed

S&F Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete including provn of plain cement concrete 1:3:6, type C-1 (using 20 mm graded crushed stone aggregate) bedding, connection to trap, outgoing flushing pipe, anti syphonage pipe,100 mm bore 'P' or 'S' of pipe etc complete all as specified and directed.

S&F Vitreous China urinals half stall type, complete including providing and fixing plugs, bedding urinal against wall in cement mortar1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed .

S&F urinal partition with 10mm thick toughened glass including edging complete all as specified and directed.

S&F Vitreous china wash basin, white, flat back, size 550mmx400 mm fixed on and fixing on cantilever brackets of mild steel angle 35mm x 35mm x 5mm, 32mm dia brass waste coupling and 32mm dia PVC waste pipe (rigid quality) including pedestal, complete all as specified and directed.

S&F Brass CP mixture for mixing hot and cold water, single hole type as in WHB, screwed down for iron pipe for 15mm dia bore pipe, complete all as specified and directed.

S&F 15 mm dia fancy type chromium plated with long shank and cup ( angle valves) cast copper alloy, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe or for union complete and all as specified and directed

S&F 15 m dia bib taps, chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule, complete all as specified & directed

S&F PVC low level flushing cistern 10 litres capacity, white, with all fitting and fixtures including brackets and 32 mm bore PVC flush pipe complete all as specified and directed.

S&F PVC connections 15 mm size with PTMT nuts of length 450 mm complete all as specified and directed.

S&F Tubular towel rail of brass chromium plated, 20 mm dia, 'D' type, 60 cm long between flanges including brackets fixed complete all as specified and directed.

S&F jet for pedestal pan, chromium plated of standard size complete all as specified and directed.

M&L for applying two coats of white wash including preparation of newly plastered surfaces of wall complete all as specified and directed.

M&L for applying two coats of white wash including preparation of newly plastered surfaces of ceiling complete all as specified and directed.

M&L applying two coats of cement base paint including preparation of newly plastered surfaces of ceiling complete all as specified and as directed.

M&L providing water proofing treatment over cleaned roof surface with APP modified bituminous membrane, comprising of the following and testing of following:- [a] 10 mm thick rendering or screed bed or bedding layer in cement sand mortar 1:4 mixed with water proofing compound @ 3%by weight of cement and surface finished even & fair. [b] Applying one coat of bitumen primer @ 0.3 Litre per Sqm on plastered surface. [c] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [d] Providing APP modified polymeric water proofing membrane having weight not less than 3 Kg per Sqm with 100 mm wide side or end lap and joint sealed with flamed torched pasted over full length [e] Applying one coat of hot blown bitumen 85/25 grade @ 1.2 Kg per Sqm. [f] Spread coarse sand over entire bitumen surface and than topping with 40mm thick brick tiles laid over & including 15 mm thick screed bed in cement sand mortar 1:6 & joints shall be pointing with CM 1:3 complete.

Supply only water proofing compound complete all as specified.

S&F Urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (Minimum weight 60gms) complete all as specified and directed.

Supply only pillar tap cast copper alloy with capstan heads chromium plated fancy type screwed down high pressure with or without lettered hot or cold with long screwed shank and fly nuts, screwed for iron pipe 15 mm bore complete all as specified and directed.

S&F Sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed .

M&L for Point wiring complete with PVC insulated unsheathed 1100 volts grade cable 1.5 Sqmm(nominal area) FRLS having stranded copper conductor single core drawn in and including 20mm dia rigid PVC conduit medium grade ISI marked including all conduit accessories for concealed pressed steel terminal box of required size not less than 1.6mm thick factory made duly painted inside and outside with two coats of black bituminous paint over and including a coat of red oxide primer with 3mm thick top cover of plastic laminated sheet/required colour for mounting switch socket/fan regulator etc including 1.5 Sqmm PVC insulated unsheathed cable FRLS having copper conductor as earth wire and connected earth dolly as required at the site complete for the following:- (a) One light or fan point controlled by one way switch

...ditto all as per Item No. 91 above but for 3 pin 5 Amp socket outlet on independent board

S&F switch piano flush button single pole one way 6 Amps, 240 volts complete all as specified and directed.

S&F Socket flush type 5 pin 5 Amps shutter complete all as specified and directed.

S&F Ceiling rose surface Bakelite 65x25mm three terminals 240 volts complete all as specified and directed.

S&F sheet metal enclosure factory made, Double door,4ways, single pole with 200 Amps rated bus bar for housing MCBs/isolators complete including provn of blanking plate for unused ways complete all as specified and directed.

S&F MCB SP, 6 to 32 Amps, 230 volts,10 KA complete all as specified and directed.

S&F MCB SPN 40 Amps, 230 volts 10 KA complete all as specified and directed.

S&F pendent holder ordinary/ bracket/angular type, brass with insulated body lamp holder, cord grip pattern complete all as specified and directed.

S&F LED retrofit lamp of capacity 12/15 watt, B-22 holder base with polycarbonate body and aluminium heat sink Day light white complete all as specified and directed.

S&F LED light fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose including connection complete all as specified and directed. Cat Part No................

S&F Building security/street LED light fitting 35 watt IP-65 protection pressure die cast aluminium body ,heat resistant glass ,including driver and making necessary electric connection with 2.5 sqmm twin core copper wire 1.5 long complete including fixed on GI pipe medium grade of suitable size with mounting bracket complete all as specified and directed. Cat Part No................

S&F Heavy duty high speed metal body, copper winding exhaust fan, 300mm sweep, single phase 240 Volts complete with louver shutters and all accessories complete all as specified and directed.

S&F water heater storage type, electric, capacity 25 litres, BEE 5 star rated, complete all as specified and directed Model No……..

S&F LED light fitting 1x9W/1X10 W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size.

M&L for sub main wiring with two single core PVC insulated & unsheathed cable 4.0 Sqmm (nominal area) FRLS type having multi-stranded copper conductor drawn in and including not less than 20 mm dia rigid PVC conduit 'medium grade' ISI marked including all conduit accessories for concealed wiring with and including 4.0 Sqmm FRLS type PVC insulated unsheathed cable solid copper conductor as earth wire connected to common earth as per IS & cutting chasing for conduit & sinking for boxes & making good to walls disturbed surface & applying finishes to match existing surface complete including taking down of existing sub main wiring complete all as specified and directed. NOTE : Two runs of 4 Sqmm and one run of 4.0 Sqmm cable and PVC conduit shall be measured as a one unit length.

...ditto all as per Item No. 91 here-in-before, but for 5 pin 15 Amp socket outlet on independent board with 2.5 Sqmm

S&F switch socket combination 2 in 1, 6 pin 16Amps multipurpose type 240 volts complete all as specified and directed.

M/S DEEKSHA CONSTRUCTION

GAYDIN CONSTRUCTIONS

M/S SWATI CONSTRUCTION

L.K.R.TIWARI CONSTRUCTION