Construction of New Govt. Medical College (GMC) Handwara, District Kupwara

Amount

PART (A) CIVIL WORKS GMC & TEACHING HOSPITAL: Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead upto 50 m and lift upto 1.5 m in -All kinds of soils.

Earth work in excavation by mechanical means (hydraulic excavator) in trenches for foundations, drains, pipes, cables etc. (not exceeding 1.5 m in width) and for shafts, wells, cesspits and the like not exceeding 10 sqm on plan, including dressing of sides and ramming of bottoms lift upto 1.5 m, including getting out excavated earth and disposal of surplus excavated earth as directed, within a lead of 50 metres: All kinds of soil :

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20 cm in depth, consolidating each deposited layer by ramming and watering, lead upto 50 m and lift upto 1.5 m.

Supplying and filling in plinth with fine sand under floors including, watering, ramming, consolidating and dressing complete.

Excavating, supplying and filling of local earth (including royalty)by mechanical transport upto a lead of 5 km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Diluting and injecting chemical emulsion for POST-CONSTRUCTIONAL antitermite treatment. Treatment of soil under existing floors using chemical emulsion (Chlorophriphos/Lindane E.C. 20% with 1% concentration) @ one litre per hole, 300mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor:

Supply and laying of dry stone soling hand packed infoundation trenches and floors.including compacting etc complete job.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size).complete job.

Providing and laying in position cement concrete of specified grade including curing but excluding the cost of centring and shuttering. All work upto plinth level with: 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 40 mm nominal size).complete job.

Providing and laying damp-proof Course 50 mm thick with cement concrete 1:2:4 (1 cement:2 coarse sand: 4 graded stone aggregate 20 mm nominal size) and curing complete

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm bed of dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth and curing complete job.

Reinforced cement concrete work in walls (any thickness) including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts upto floor five level including curing but excluding cost of centering shuttering, finishing and reinforcement. 1:1½:3 (1 cement : 1½ coarse sand : 3 graded stone aggregate 20 mm nominal size).complete job.

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete complete job.All work up to plinth Level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete complete job All works above plinth level upto floor V level

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete above plinth level Primary producer Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for: Foundations, footings, bases of columns etc. for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for: Suspended floors, roofs, landings, balconies and access platforms.

Centering and shuttering including strutting, propping etc. and removal of form for: Lintel, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for: Columns, pillars, piers, abutments, posts and struts.

Centering and shuttering including strutting, propping etc. and removal of form for: Stairs (excluding landings) except spiral staircases.

Brick work with common burnt clay (non-modular) bricks of class designation 7.5 in foundation and plinth including curing in : Cement mortar 1:4 ( 1 cement : 4 coarse sand)

Providing and laying autoclaved aerated cement blocks masonry Grade-1 750 KG/m3 density with125mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately). Make :Magicrete, Ambuja, aerocon

Providing and laying autoclaved aerated cement blocks masonry Grade-1 750 KG/m3 density with125mm/230mm/300 mm thick AAC blocks in super structure above plinth level up to floor V level with RCC band at sill level and lintel level with approved block laying polymer modified adhesive mortar all complete as per direction of Engineer-in-Charge. (The payment of RCC band and reinforcement shall be made for separately). Make :Magicrete, Ambuja, aerocon

Providing and fixing colour precoated galvanized iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side ofthe sheet and polyester top coat 15-18microns. Sheet should haveprotective guard film of 25 microns minimum to avoid scratches duringtransportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drillingself tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto/any pitch in horizontal/ vertical or curved surfaces, excluding the cost ofpurlins, rafters and trusses and including cutting to size and shapewherever required.

Providing and fixing precoated colour galvanised steel sheet roofing accessories0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 1518 microns using self drilling/ self tapping screws complete: a. ridges , valley, gutters(500-600 mm)

6 mm cement plaster to ceiling of mix 1 : 3 (1 cement : 3 fine sand)

12 mm cement plaster of mix :cement plaster 1 : 6 (1 cement : 6 fine sand)

15mm Cement plaster on the rough side of single or half brick wall of mix cement plaster 1 : 6 (1 cement : 6 fine sand)

Providing and applying surface Ceramic textured finish protection coating (Ceramic of approved shade or approved equivalent make) to external wall surfaces comprising of water-borne, penetrating, water repellent EM- primer & super durable water based acrylic silicon resin clear and super durable dirt and dust resistant protection coat of FSI Clear coat, which shall be highly water repellant, Anti-algae & anti-fungal in nature. The coating shall also cover hairline cracks with application method which includes 1 coats of El primer, 1 coats of Ceramic, all in approved color and texture including preparation of surface, appropriate primer coat etc. applied as per manufacturer's instructions complete & project consultant instructions, allow for scaffolding, staging as required. The finish shall be natural color/ non pigmented, water repellant, resistant to condensate formation, cover hairline cracks/ crazing, UV & alkali resistant & ensure good breathability for the substrate all to the satisfaction of the engineer in charge THICKNESS : 1.25 -1.5 MM .

Providing and applying white cement based putty of specified thickness, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.2 mm thick

Wall painting with premium acrylic emulsion paint of interior grade,having VOC (Volatile Organic Compound ) content less than 50 grams/ litre of approved brand and manufacture, including applying additional coats wherever required to achieve even shade and colour.Two coats

Providing 40x5 mm flat iron hold fast 40 cm long including fixing to frame with 10 mm diameter bolts, nuts and wooden plugs and embeddings in cement concrete block 30x10x15 cm 1:3:6 mix ( 1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size).

Providing and laying full body polished /matt Vitrified tiles in floor with different sizes (thickness to be specified by the manufacturer), with water absorption less than 0.05% and conforming to IS0: 10545:2/IS-13006, of approved brand and manufacturer, in all colours and shades, laid with cement based high polymer modified quick set tile adhesive (water based) conforming to IS: 15477, in average 6 mm thickness, including grouting of joints (Payment for grouting of joints to be made separately).Size of tile 800x1600 mm.complete job.approved brand and iso certified. Make : Nexion,Simpolo,Maps, kajaria .Tile Adhesive make:Magicrete, Ardex endura, latticrete.(forTile Adhesive )

Grouting the joints of flooring tiles having joints of 3 mm width, using epoxy grout mix of 0.70 kg of organic coated filler of desired shade (0.10 kg of hardener and 0.20 kg of resin per kg), including filling / grouting and finishing complete as per direction of Engineer-in-charge.Size of tile 800x1600 mm complete job.approved brand and iso certified. make:Magicrete, Ardex endura, latticrete.

Providing and laying rectified Glazed Ceramic floor tiles of size 600x600 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, laid on 20 mm thick cement mortar 1:4 (1Cement : 4 Coarse sand), including grouting the joints with white cement and matching pigments etc., complete In all colours, shades, except White, Ivory, Fume Red Brown.complete job.approved brand and iso certified.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete. Size of tile 600x1200 mm. Make : Brown.complete job.approved brand and iso certified. Make : Nexion,Simpolo,Maps, kajaria .

Providing and laying Polished Granite stone flooring in required designand patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with whitecement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge.11.68.1 Polished Granite stone slab adhunik brown, brazilian grey/white, jet Black, Cherry Red, EliteBrown, Cat Eye or equivalent complete job.approved brand and iso certified.

Supply and fixing of water proofing by Preparing surface free from any laitance, dirt debris or loosely held material. Job warranty by OEM of 10 year min.The moisture on concrete surface must be less than 5%. All bugholes must be repaired with polymer modified mortar and all existing cracks must ideally be filled by injection grouting All corners must be strengthened with Weber stickon tape / Weberdry Fabric 65 or equivalent sandwiched between 2 coats of Weberdry PUR Details. Applying 1 coat of epoxy primer Weberprim Epox 501. After a gap of 12 hours, applying 2 coats of 2-component, solvent free, food grade waterproofing membrane Weberdry PUR Seal 2K or equivalent over the complete surface. Oven dried silica sand must be broadcast on final coat of Weberdry PUR Seal 2K or equivalent while wet to ensure proper adhesion with subsequent tile adhesive. All tiles must be fixed with suitable Weber tile adhesive. The gaps in joints must be filled with 2 component epoxy grout - Weberepox Easy or equivalent.make : BASF, Weber , Superma. complete job.approved brand and iso certified.

Structural steel work welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete job.

ZINC Flat lock Tile SystemProviding and fixing of Titanium Zinc Flat lock - 425 mm flat lock tile System in 0.7 mm thick in comprising of the following layers:Top Layer – Supply & Installation of zinc titanium Flat lock wall cladding system in pre weathered Nova finish 0.7 mm thick consisting of Fixing clips & strips made of galvanized steel.to connect the zinc panels to the decking sheet. Panel Size shall be 425X425 mm maximum. All installation is to be carried out by approved trained roofing installer. The installation team shall be fully trained and approved by the manufacturer. The sheeting Supplier shall have ISO 9001/14001 quality certifications for their manufacturing units.Pre-weathered titanium zinc with a matte subtle brushed surface in a natural medium-grey colour. The uniform medium-grey surface of Zinc originates after a chemical surface treatment following the rolling process. A temporary organic layer as a top coat is also applied to protect the surface against fingerprints (AFP). An Anti-Fingerprint coating is applied to prevent fingerprints during installation and to optimize machine processing. AFP coating shall be provided from original sheeting manufacturer with certificate. No Permanent coating or lacquer layer should be applied as a top coat. The material properties shall be as follows: Ultimate tensile strength: minimum 150 N/mm2,0.2% Proof Stress: min 110 N/mm2. All installation is to be carried out by approved trained roofing installer. The installation team shall be fully trained and approved by the manufacturer. The sheeting Supplier shall have ISO 9001/14001 quality certifications for their manufacturing units.The zinc roofing sheets shall be as per EN 988 standards .complete job.approved brand and iso certified. 2) SECOND LAYER- Anti-abrasive breathable membrane - Anti abrasive made of High density polyethylene film in grey colour. Membrane shall be 0.6 mm thick as per zinc sheeting recommendations4) FOURTH LAYER - 0.47mm TCT Hi-Tensile steel sheets profile with nominal 3.0 - 4.0 mm deep ribs at pitch of nominal 48 - 52 mm as per zinc sheeting recommendations. Purlins to be provided at a apscing of 1000-1200 mm centre to centre maximum.Purlins to be provided at a apscing of 1000-1200 mm centre to centre maximum.ZINC FLASHING IN 0.70 MM THICK.Supply & fixing of 0.7 mm zinc flashing of Maximum Girth 166mm in the same finish as thecladding finish for eaves , junctions, gables ,ridges,fascia,gutters ,etc as required for site detailing .MAKE LIST : NEDZINK, SILESIA, JARDEN, ROOFINOX

Providing and laying rough finished Full Body vitrified tile of specified size having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in outdoor floors such as footpath, courtyard multi models etc., of R11 grade laid on 20mm thick base of cement mortar 1:4 (1cement: 4 coarse sand) in all shapes & patterns including grouting the joints with 5 mm spacer and epoxy upto tile surface with matching pigments etc. complete job as direction of Engineer-in-Charge. Size : 12 mm thick of size 200 mm x 200 mm.complete job.approved brand and iso certified.

Supply & Installation of top mounting factory finish modular balustrade system for staircase and atrium of AISI 316 L grade consisting of top handrail size Dia.38x1.5mm thick in SS 316 L fixed on top of upright of size dia.30x1.5mm thick & fixed on top of RCC with base plate dia.87x8mm thick SS 316 L and 2 nos. of M10x120 anchor fasteners at the max span of 1500mm (center to center).3 nos. mid rails dia. 16x1.5mm thick in SS 316L fixed to upright with ss holder. All screws, bolts, and accessories are to be in ss matte finish. Overall railing height would be 1050 from FFL to top of handrail. Make : make : technorail, Dorma,Qrail.

Providing and Fixing WPC Teak textured Wood finished doors frames of size 125mm x 63 mm

Providing and fixing ISI marked flush door 32mm +1 mm laminate both faces ) thickshutters non-decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shuttersand 1mm laminates on both the sides including ISI marked SS 2 ball bearing hinges , SS handles (doorset- hl brt sc), SS locks set , SS towerbolts( 10 mm dia ss TS series 1010&810), with necesssary screws with lipping with 2nd class teak wood battens 12 mm minimum depth on all edges of flush door shutters with PU Finsih polish of approved shade .(over all area of door shutter to be measured) . (With 10 years Warranty ). Makes : Greenply, Merino, Samrat,Century, complete job.approved brand and iso certified.

Supply and installation of Cabin System for minimal frame, room dividing solutions.Double glazed mullion free demountable glass partition using Toughened/ Laminated glass in proprietary natural anodised/Black anodised aluminium sections of size 100mm x 30mm with Concealed sealing (No visible Gasekts/Seals) with acoustic rating of upto 50 dB with third party test certificate. The profile will have Carpert Groove at the Bottom on both sides for accomodating max. 8mm carpets.It should consists of intermediate slim junction profiles for Glass to Glass vertical joints, 90 Degree L Junction and T Junction profiles suitably to be used as per room configuration designs.No VISIBLE Clip Lines to provide clutter free view at both side of section. Optional Profile Bottom Seal pair for additional accoustic if required. Glass thickness - 10mm +10 mm. All Profiles are min 1.5mm thickness excluding 20 microns of Anodizing, Standards applicable •Structural stability test accordance to BS 5234: Part2:1992 & EN 1991-1-1:2002 • Acoustic test for sound insulation in accordance to DIN EN ISO 10140-2 ASTME-E 90 • ALT profile sections are manufactured and tested in accordance to EN573-3, EN755-2, DIN EN 12020 T2 , non-dimensions manufacturing tolerance deviation DIN ISO 2768-1 class C = coarse • Toughened glass complies accordance to BS 6262 (glass supplier specification from market) • Environmental product declaration (EPD) rating accordance to ISO 14025 & EN 15804 • HPDs - Ref HPD Unique Identifier; 22451 & 22452 - Classification : 09 84 00 Acoustic Room ComponentsALTERRA or equivalent 100 DG profile being modular shall have feature of converting existing Double glaze into Single glaze without disturbing Finished areas/ removing existing partition system. Max System Height - 3000mm complete job.approved brand and iso certified.

Supply & Fixing of ALT 100 SG Aluminium Glazed Door (Single Leaf/Double Leaf) with Glass infill of toughened/Laminated glass with Alterra or equivalent rebate door frame System all around the door. Aluminium Stile to be formed out of 70x35mm Horizontal and Vertical Door Profile frame with clips & seals. Door Hardware -Flush Hinges , Slide Arm - Door Closer TS 70 Sleek body, pull handle 600x25 mm with narrow stile lock epc both side key operation , SS304, SSS with Antimicrobial Coating as per ISO 22196 and antiviral activity with 99.9% reduction as per ISO 21702. with Narrow stile Lock package and Door Drop down seal.Suitable for Glass thickness of 10 mm.The Profile shall be matt natural anodized/Black, the Profile Manufacturer to supply all the necessary clips, seals and fixing accessories for the system. All Profiles to be with 1.5 mm Gauge thickness Excluding 20 Micron of Anodizing. 100SG Stile Door complete assembly - 1000x2100mm - Black Anodizing

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of raw plugs at 450 mm centre, with 25mm long drywall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of drywall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering up to 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cut outs made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum resistant board.complete job.approved brand and iso certified.

Providing & Fixing of perforated Acoustical Suspended Ceiling System – Tegular edge tile Lay in on 24 mm exposed Grid. The high Grade MDF panels with fleece having melamine laminated faced with hole or Slot system for providing sound absorption via acoustic impedance method. The tiles should have Humidity Resistance (RH) of 99%, NRC 0.80, Light Reflectance >84% with Fire Resistance as per BS476 (Part 6 & 7) in module size of 595 X 595 X 12 mm@ 400kg/m3 density. The Grid should be 24 mm wide T sections i.e. the Main Runner 3000mm in web height of 32 mm, 1200 mm & 600 mm Cross Tees in web height of 26mm to comprise main runner spaced at 1200mm centers securely fixed to the structural soffit using suspension system at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm center to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centers and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge. MAKE: ANAKON/HUNTER DOUGLAS/ECOPHON

Providing & Fixing of Magnetitte Pine Wood tile made of mineral wood fibers magnetite bonded having thickness of 15MM tile Suspended on 24 mm strong Grid. The tiles should have Humidity Resistance (RH) of 90%, NRC 1.00, with Fire Rating as per BS476 (Part 6 & 7) in module size of 595 X 595 X 15 mm@ 400kg/m3 density. The tile should have color option as per architect/person in charge. Tile would be backed with 50mm insulation@48kg density to achieve desired level of acoustic. The grid should be 24 mm wide T sections i.e. the Main Runner 3000mm in web height of 38 mm, 1200 mm & 600 mm Cross Tees in web height of 26mm. Installation to comprise main runner spaced at 1200mm centres securely fixed to the structural soffit using suspension system at 1200mm maximum centre. The First/Last suspension system at the end of each main runner should not be greater than 450mm from the adjacent wall. Flush fitting 1200mm long cross tees to be interlocked between main runners at 600mm centre to form 1200 x 600 mm module. Cut cross tees longer than 600mm require independent support. 600 x 600mm module to be formed by fitting 600mm long flush fitting cross tees centrally between the 1200 mm cross tees. Perimeter trim to be wall angles of size 3000x19x19mm, secured to walls at 450 mm maximum centres and as per the drawing and the work complete in all respects to the satisfaction of Engineer in-charge. All accessories consisting of HLC Sleeve Fasteners of thread size 6.5mm x 25/5 with Soffit Cleat made of Galvanized steel of size 27 x 37 x 25 x 1.6mm and Level Clip in dimensions of 85x30x0.8mm with 4.00 mm GI wire . MAKE:ANAKON/BAUX/ECOPHON

Providing and fixing of breach coffer having system NRC up to 0.88 with oval slate slotted 9.5mmx76.2mm with size 300x2400mm. The high grade breach coffer with stripped locking system for seamless mounting having density of 850-900kg/m3(base coffer confirming to IS 12406 and laminated coffer confirming to IS 14587). The back of the coffers are breached with a nonwoven fabric covering of 0.2mm for providing Sound absorption via the acoustic impedance method. coffer is fixed by using GI Framework 2400mmx50mmx0.50mm spaced at 600mmx600 c/c & 12 mm ply framework spaced at 400mm centres with suitable brackets and the system is backline with acoustical webbing 50mm@48kg density and along with all accessories example: chicken mesh and all. MAKE:ANAKON/HUNTER DOUGLAS/DECOR SYSTEM

Providing and Fixing of Spandex System on G.I studs 2400mm X 50mm web flanges 15 & 50mm fully knurled giving it high strength, hot dipped galvanized steel With 120GSM zinc coating specially designed for Acoustic vibration management and long life with a backing 50mm thick Rock wool @48kg density insulation intact with chicken mesh wires. 1200x1200mm breach with 10.0mm with the distance of 22-25.0mm each hole giving the NRC 0.9-1 to be mechanically fastened on the G.I Studs. Then 12mm clip rail system are screw fixed on the breach coffer .Then the Spandex is stretched over the clip rail system as per Architect choice-Ref attached specifications for more details. complete job.approved brand and iso certified.

Providing & fixing 15mm thick coloured Acoustic Panels in size 1220 x 610mm of Natural panel having Premium Square Edge. Panels are made of Pine Wood fibers containing cellulose binded with Magnesite. The panels will be screw fixed @ 200mm on GI metal frame of 50 x 50mm making a grid of 610 x 610mm c/c. The frame is to be made in proper line after leveling. The panels will be backed with 50mm Rockwool of 24 kg/cum inserted inside the grid of 610 x 610mm which will comprise of minimum NRC 0.90 as per IS: 8225/ ISO: 354/ ASTM: 423 – 90 a. The panel meets the stringent fire test required having Class ‘P’ rating for Ignitability test as per BS 476 part 5 and Class ‘1’ rating as per BS 476 part 7 for Surface Spread of Flame test. Class ‘P’ and Class ‘1’ are the highest rating. BS 476 part 6 Fire Propagation index, I = not greater than 4.11. It should meet all technical parameter.complete job.approved brand and iso certified.

Providing and Fixing Acoustical Wooden Stage Flooring Compatible with Underground signal cabling and Pop-Up Boxes: Providing and fixing 65/75 X 18 thick in random length, 2nd class teak wood planks flooring with tongue and groove joints on a layer of 15 mm thick Engineering wood of approved make and manufacture, fixed to hardwood joint 50 X 50 mm at 600 mm c/c in one direction and 60 X 50 mm Sal battens 600mm c/c on other direction, Hardwood joint resiliently supported on 100 X 100 mm Rubber Pads, the framework to be filled with 50mm thick Insulation Wool resin bonded insulation of density 24kg/cum. PU polishing of teakwood on the exposed surface: In horizontal/vertical plane (rate for flooring shall include providing additional framework required for housing microphone and power outlet junction - signal & Popup Stage boxes, If required providing and fixing hinged 18mm thick Engineering wood cover for the junction boxes. Work complete in all Respect. The Work shall be executed as per drawings, Specifications & Instruction of engineer in charge.MAKE: ANAKON/ARMSTRONG/ECOPHON

Provided & fixing stage Proscenium to be fabricated on site made top side with 50x50mm MS square pipe. left and right proscenium wall fixed by using GI Framework spaced at 600mm c/c aluminum framework system is backline with 50 mm Roxul Rockwool and along with all accessories Infill in rockwool insulation padding. Fixing on 12 mm waterfroof ply.finishing with 1mm sun mica approved.

Supply, Installation, Testing and commissioning of Rotatable Side wings made with 50 x 25 mm square pipe with rockwool insulation insode and covered with 6mm ply both side over which stretch fabric of black colour to be applied.

Supply, installation, testing and fixing of Stage frills to be installed above the stage on 28mm dia GI pipe adjustable at position according to stage positioning plan. Cloth material of desired shade with Stitching.

Supply, installation, testing and fixing of MAIN FRONT VERTICAL CURTAIN made out of glazed cotton cloth with verticaly upward and Downward arrangement complete with fixing rails, brackets, moterised opration complete with required gear box, mini drums, weights, limit swithes, cuplink, runners, master runners,pullies, 3mm steel rope wire, 2HP motor (Crompton). 2 nos air breaker contactors (L&t/Siemens). Push buttton for stop, upward and downward positions.Motor mounting with C channel platform on side wall. Curtain cloth should be fire retarhdant.

Supply, installation, testing and fixing of MIDDLE CURTAIN made out of glazed cotton cloth with horizontal sliding arrangement complete with fixing rails, brackets, moterised opration complete with gear box, runners, master runners,pullies, 3mm steel rope wire, 1HP motor (Crompton). 2 nos air breaker contactors (L&t/Siemens). Push buttton for stop, forward and reverse and close positions. minimum overlap at centre 900mm. The curtain stitched in double gathering.Curtain cloth should be fire retarhdant.

Supply, installation, testing and fixing of REAR CURTAIN made out of glazed cotton cloth with horizontal sliding arrangement complete with fixing rails, brackets, moterised opration complete with gear box, runners, master runners,pullies, 3mm steel rope wire, 1HP motor (Crompton). 2 nos air breaker contactors (L&t/Siemens). Push buttton for stop, forward and reverse and close positions. minimum overlap at centre 900mm. The curtain stitched in double gathering.Curtain cloth should be fire retarhdant.

Proving & Fixing of floor covering carpet roll having pile construction of tufted loop pile with composition of 100% nylon, Flammability pass as per 16 CFR 1631#,smoke density ASTM E 662 less than 450,risilient primary backing of woven polypropylene, antistatic, anti skid property for commercial use, thickens 4-5mm and approximately pile weight of 850g/m2 of roll form with total weight of 1500 g/m2,roll length + roll width of 30mtrs/400cm,primary backing of action black/felt back with ecoflex NXT, light fastness of >4 and sound insulation of DLW 28db,thermal resentence :0.9 (m2) kw ,installed over existing Cementitious flooring with gorilla epoxy glue, spinta colour series or equivalent colour complete as directed by engineer-in-charge.complete job.approved brand and iso certified.

Supplying and Fixing of Radium glow Stair case Nose made out of anodized aluminium profile having UV exposure shrinkage, anti slip resistance comes in different colour and sizes with the length of 2.5mtrs

Providing and fixing Fully Insulated Non Metallic Wooden Fire door at all levels. Wooden fire door should carry 120 minutes Insulation properties. Main Door frame shall be Single rebate profile of section 120 x 70 mm made out of Hard wood - Red merandi / Ivory Coast (2nd class ) as per requirement with factory made groove of suitable size so as to accommodate Fire & smoke seal of size 20x4mm . The frame must be primed with Fire retardant primer. Wooden shutter must be of minimum 52mm of thickness finished with commercial ply on both faces. The commercial ply must be finished with Fire retardant primer. The Commercial ply may also be pasted with Laminate in desired shade (payable in extra item). The composite thickness of the core insulation will be 44mm consists of Calcium Silicate boards of approved make and treated wool Insulation material. The shutter should be provided with heat activated intumescent fire seal strip of size 20mm x 4 mm mounted in the suitable grooves all three sides except bottom provided on Exposed OR concealed wooden lipping . Vision panels wherever required should be of 120 minutes fire rated clear non?wired type. All hardware’s, Fasteners and FR Glass shall be payable in Extra item. Door shutter provided with commercial ply on both faces with 1mm Thick Regular SF grade Factory pasted Laminate on both faces and Main frame made out of hardwood frame. Frame primed with Fire retardant primer.FIXTURES OF DOORS: (A) Supply & fixing of SS Ball Bearing Hinges of size 100 x 75 x 3mm complete with SS Screws of BB1953 Becker Fire Solutions / DORMA 3090F / GEZE Mak (4 No’s per panel), (B) Supply & fixing of anchor fasteners of HILTI/ FISHER/ Equivalent of M10X120mm length. (C) Supply & fixing of door closers of BLC-604 Becker Fire Solutions/ TS-89 DORMA / GEZE TS 2000 Series Make. (Except shaft door). (D) Supply & fixing of Stainless Tower Bolt 300mm Long for Double leaf door of height up to 2100mm of Becker Fire Solutions. / Dorset Make with necessary screws as required. (E) Supply & fixing of Stainless Tower Bolt 600mm Long for Double leaf door of height up to 2400mm of Becker Fire Solutions. / Dorset / EQ make with necessary screws as required. (F) Supply and Filling the gap between wall & Door frame by using silicone sealant and Wool insulation on both side of the door

PUBLIC ADDRESSABLE SYSTEM(PAVA) : Supply,installation,testing and commissioning 6 Zone EVAC Controller, built-in 500W class-D amplifier, built-in EVAC and alert voice message by SD card, with fireman microphone, with AB speaker line low impedance supervision, with amplifier auto changeover into standby when fault, with extension amplifier connector, AC and DC battery operation (makes Labgruppen, QSC, CROWN)

Supply,installation,testing and commissioning of Remote Paging Microphone, 12 zone capacity with 12 keypad buttons, each system can connection up to 32 remote microphone, DC24V power supply. (makes Midas)

Supply, installation, testing & commissioning of Booster Amplifier capable of delivering 480 Wattage RMS power output for speakers, built-in fan for temperature control, built in line matching transformer distortion typically < 3% @1 KHz, S/N> 80 dB complete as required." complete job.approved brand and iso certified.

Supply,Installation,Testing & Commissioning of 4" 6W Ceiling Speaker with SPL at rated power/1W 92dB (1m & 1kHz). Frequency response of 125Hz – 16kHz (-10 dB with reference to 1kHz). The speaker should have tappings at 6W/3W/1.5W." complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of 15W Wall mount with max SPL 1M/6W 96dB . Frequency response of 110 Hz ~13K Hz. The speaker shoud have tappings at 6W/3W

Supply, installation, testing and commissioning of Surface Mounted / Pole Mounted with 15W BOX Type Horn Loudspeaker for Evacuation Systems, Max power 25W Power tapping @15W/7.5W. Sound pressure level 15W/1W (1m, 350Hz~7kHz) - 115 dB / 103 dB. Dispersion angle (1k Hz / -6 dB) 140 degree. The entire unit shall be Water and dust proof , IP66 compliant. The item cost shall be complete with all necessary mounting hardware & accesories and shall be as per the list of makes and complete as required..

Supply,Installation,Testing & Commissioning of 4" 6W Ceiling Speaker with backbox and with SPL at rated power/1W 92dB (1m & 1kHz). Frequency response of 125Hz – 16kHz (-10 dB with reference to 1kHz). The speaker should have tappings at 6W/3W/1.5W." (complete job.approved brand and iso certified.

Supply & Laying of 2 core *1.5 Fire Survivial cables certified BS 6387 CWZ PH 60 through BRE Global UK 2C1,50sqmm+E multicore cable 300/500V; Stranded (Class2), Copper conductor; Special Silicon Rubber mix insulation type EI2; Polyster tape 50% overlap plus; Polyster tape 50% overlap Aluminium/Polyester tape, metallic side down, in contact with Solied Copper drain wire Outer Sheath LSZH Sheat type LTS3 Max HCL emission @ 800° C: -0.5%; Core identification following BS 7629: 1997; Fire rated 3 hours at 950°C as per BS 6387 and flame retardant as per IEC 60332.3. Certifiction: LPCB,

FIRE ALARM SYSTEM: Supply, Installation, testing and commissioning of EN54/VDS approved Microprocessor based intelligent addressable fire alarm panel, 100% electronically addressable system where field device addressing is done by panel and not by user, LED panel display, single loop with minimum 255 addressable points ( detectors + Devices) per loop, panel with built in battery that can support backup up to 24hours idle condition and 30 minutes during alarm condition, 4 sounder circuits, Event history of 9,999 logs, option to load Logo on the main screen, view live analogue level of field devices on the panel screen, NAC power supply units that are loop mountable and 100% supervised from main panel. The Networkable FACP shall be able to accommodate below given detectors & devices as per boq and shall have 20% spare capacity to accommodate future expansions of addressable points. complete job.approved brand and iso certified.

Supply, installation, testing and commissioning of EN54/VDS approved Addressable 2 wire Multi-Criteria Detector ( Photoelectric Smoke + Heat detection) with built-in short circuit isolator, 100% soft addressing, single LED that covers 360Deg lightpipe technology, Drift compensation. Detector should be provided with Base.complete job.approved brand and iso certified.

Supply, Installation, testing and commissioning of EN54/VDS approved Addressable 2 wire break glass manual call point with built in short circuit isolator, 100% soft addressed from panel, Wall mounting, resettable key option with back box.complete job.approved brand and iso certified.

Supply, Installation, testing and commissioning of EN54/VDS approved Addressable loop powered Wall mount sounder with strobe & built in isolator, 100% soft addressed from panel, with 3 tones provided with back box & all accessoriescomplete job.approved brand and iso certified.

Supply, installation, testing and commissioning of EN54/VDS approved Addressable 2 Wire monitor module, 100% soft addressed from panel, integral short circuit isolators, capable of monitoring NO contacts, Option to choose operation mode as supervision of 20Sec or activation immediate to connect NO/NC contacts such as pressure switch, flow switches, fire pump contacts etc. provides with all accessories

Supply & Laying of Communication cable from panel to field devices 2 core *1.5 Fire Survival armoured cables certified BS 6387 CWZ PH 60 through BRE Global UK 2C1,50sqmm+E multicore cable 300/500V; Stranded (Class2), Copper conductor; Special Silicon Rubber mix insulation type EI2; Polyester tape 50% overlap plus; Polyester tape 50% overlap Aluminium/Polyester tape, metallic side down, in contact with Soiled Copper drain wire Outer Sheath LSZH Sheet type LTS3 Max HCL emission @ 800° C: -0.5%; Core identification following BS 7629: 1997; Fire rated 3 hours at 950°C as per BS 6387 and flame retardant as per IEC 60332.3. Certification: LPCB,

Supply, installation, testing and laying of 2 core 1.5sqmm – flexible armored cable for luminaire power supply.

STAGE LIGHTING : Supply Installation Testing and commissioning of 150W High Quality LED Parcan Light, Lamp source 3200K or better Colour temperature, Beam Angle of 9˚ / 25˚ / 45˚, Maximum power consumption of 165W,Fixture provided with yoke of manual adjustment,with complete accessories

Supply Installation Testing and commissioning of 200W LED Profile Spot 19 Degree Light complete with 3200K or better Colour Temperature,Efficient and well-designed Lamp reflector,sleek and unique designed light weight body,Fixture provided with yoke of manual adjustment,with complete accessories. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 200W LED Blinder Light 30 Degree complete with 3200K or better 2x100W Chip On Board LED Lamp source, beam Angle 30 Degree or better, total Power consumption of 220W, In built preset’s for effects, High quality well designed inbuilt reflector, IP20 protection with complete accessories. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 100W LED Fresnel Light having COB LED source from Philips/ Osram with 3200K colour temperature, High quality uniquely designed Fresnel Lens, LED COB Based Source .Total Power Consumption of 110W, Active Cooling with Low Noise Fan complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 54 x 3W LED Par Light RGBW Beam Angle 25° complete with LED source from Lumiled / Seoul / Nichia or reputed make, RGBW 3W Lamp source x 54 Pcs, High Bright Red, Green, Blue, White LED’s source unlimited color mixing through DmX 0 ~ 100% Linear dimming In built presets for different colors, Power In and Out Connections, High precision colors, IP20 protection, powder coated. (complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 54x3W LED 3200K Par Light 3200K 3W Lamp source x 54 Pcs LED source from Lumiled / Seoul / Nichia or reputed make, smooth fade in and fade out, High precision steady color, No heat, Powder coated Black finish housing, LED Easy view display Power In and Out Connections, total Power Consumption of 180W, Sound Active Mode Control, IP20 protection. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of SITC of 180W LED CCT tuneable Light complete with tuneable Lamp source, High precision steady color, No heat, Beam Angle 15°/ 25° / 45°, Powder coated Black finish housing, Rigidly built pressure die-casted Aluminium body, LED Easy view display Flicker Free for high FPS, Smooth fade in and Fade out, Total Power Consumption of 180W Sound Active Mode Control, IP20 protection.complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 300W LED Cyclorama Wash Light with LED source from Lumiled / Seoul / Nichia or reputed make 60 Degree or better beam spread, 48 LED Emmitters having RGB Source complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of Light fixture mouting clamp Customized Customized for suspending on fixed bars on stage, Made up of Aluminium Die casted, MS threaded T bolt with yellow passivation finish, complete with black powder coating matt black finish, safe working load 150 KG

Supply Installation Testing and commissioning of Light Fixture dual safety Chain made up of GI wire rope bundled and twisted together Having load bearing capacity above 200 Kgs, Sleve on the rope. Carabiner Clip

Supply Installation Testing and commissioning of Suspender cum clamps designed made out of MS material 150mm x 150mm x 5mm MS base plate, threaded rod, black powder coated finish All the materials under gone through 7 tank process with various chemical treatment to keep them rust free Suitable to hold various type grid & other rigging systems.

Supply Installation Testing and commissioning of Fixed stage Lighting bar/winch of 13Mtr length constructed with an dual contruction light bar Material for the light bar shall be of Mild Steel Pipe, dual barrel arrangement, powder coated with Matt black Texture, fixing through suspenders as per site conditions, dual construction and an additional End Caps on the pipe end shall be there Light bar Length shall be of customized type as per site condition.

Supply Installation Testing and commissioning ofFixed stage side Ladder as per the design, Size of 600mm x 2400mm Dual Barrel Arrangement, dual construction, powder coated with Matt black Texture single construction with, cross connecting Pipes at every 600mm Ladder can be moved along the track or adjusted as required, Spud & Trolley, Pivoted or Fixed suspenders as per site conditions

Supply Installation Testing and commissioning of Fixed FOH Lighting bar/winch of 15Mtr length constructed with an dual contruction light bar with an Mild Steel black matt finish with an supporting flat patti of height 200mm x 50mm x 6mm thickness for the extra support with 2 holes of 10mm diameter to fix the cable tray on the bar.It shall be hanged from the roof to accommodate various type of stage light fittings. It should hang from the roof with MS anglewhich is suspended from the fish plate of 5mm thickness which is fixed on the rcc roof with 4 anchor fastners of 10mm which can take an total load of 400KG each fastner, made out of 48mm outer dai, 40 Nominal Bore, material for the light bar shall be of Mild Steel Pipe, Dual Barrel Arrangement

Supply Installation Testing and commissioning of Power Distribution Electrical panel having a Incomer of 100A loor mount / rack mount / wall mount, miniature circuit brakers of single poles shall be fixed of different ratings from 6/10/16/25A as per the lighting fixtures.Wiring inside the module for power, control protection and instrument etc. shall be done with use of 1100 V.

Supply Installation Testing and commissioning of High quality power junction box 4 way made up of MS Sheet metal fabricated housing.

Supply Installation Testing and commissioning of High quality power junction box 2 way made up of MS Sheet metal fabricated housing.

Supply Installation Testing and commissioning of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated (In) housing

Supply Installation Testing and commissioning of High quality Dimming In junction box 1 way made up of MS Sheet metal fabricated housing (Out)

Supply Installation Testing and commissioning of DmX Loop Junction Box having 1 No. of DmX 5 Pin XLR compact Junction box powder coated with matt black texture finish paint, high temperature resistant insulator material, all metal housing offers best overall RF protection & electromagnetic shielding. Clamp arrangement for fixing or Raul plug arrangement for wall /floor fixing

Supply Installation Testing and commissioning of Internal Earthing System with copper bare conductors all along the cable trays

Supply Installation Testing and commissioning of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x150 x 40mm & 1.6 mm thickness

Supply Installation Testing and commissioning of Black Powder coated cable trays made out of MS Sheet fabricated for a size of 40 x 75 x 40mm & 1.6 mm thickness

Supply Installation Testing and commissioning of DmX Male Female Connectors 5 Pin having rubber sheeth protection for Cross connecting DmX wiring connections

Supply Installation Testing and commissioning of DmX Male Termination Connector 5 Pin soldered with required capacity of resistor for signal deframing

Supply Installation Testing and commissioning of Touch Screen based controller having 7” Multi touch screen

Supply Installation Testing and commissioning of 32-way Power Marhalling Box made up of MS Sheet metal fabricated housing black powder coated and ivery connectors for the internal terminations and external outgoing connecting points, fibre / brass glands of suitable size.

Supply Installation Testing and commissioning of FRLS Copper unarmoured Flexible cable IS694 having 12 Core each of 1.5 Sq mm size.

Supply Installation Testing and commissioning of FRLS Copper unarmoured Flexible cable IS694 having 3 Core each of 1.5 Sq mm size.

Supply Installation Testing and commissioning of 5 Core DmX Cable with Sheathed housing on the cable

Supply Installation Testing and commissioning of High quality LED COB Down light, Protection Rating : IP20, Power 30W, Beam Angle 60º. Mounting Die Cast Aluminium Body with Specular Finish AI Reflector.

Control System: Supply Installation Testing and commissioning of AV system control supports Internet Protocol version 6 (IPv6), Provides NetLinx programmers the ability to manage secure port TLS and SSH communications with a remote device or server, Ultra-Fast 1600 MIPS processor, 512 MB Onboard RAM,2 RS232/422/485 Ports,Memory Card 8 GB SD, supports external USB Solid State Drives, Should two 8-position 3.5 mm Screw Terminal, (8) single-pole, single-throw relays, NetLinx Port 21, Channels 1-8, Each relay can switch up to 24 VDC or 28 VAC @ 1 A, Each relay is independently controlled,

Supply Installation Testing and commissioning of Wireless Touch panel with charging and docking station including nesessary License for controlling application.

Supply Installation Testing and commissioning of Docking charge station for iPAD

Supply Installation Testing and commissioning of Wireless PoE enabled access point

Supply Installation Testing and commissioning of 16 port POE network managed switch

Installation Equipment : Supply Installation Testing and commissioning of 22 U Equipment Rack.

Supply Installation Testing and commissioning of Flexible 4K, 18 GBPS HDMI Cable 2 Mtr, complete as per specification & accessories as required

Supply Installation Testing and commissioning of USB-C to USB-C cable-2'

Supply Installation Testing and commissioning of Speaker Cable ,4 Sqmm Speaker cable, High performance cable for audio signals as per specification & accessories as required

Supply Installation Testing and commissioning of Speaker Cable , 16 AWG Speaker cable, High performance cable for audio signals,complete as per specification & accessories as required

Supply Installation Testing and commissioning of Microphone Cable- 22AWG, complete as per specification & accessories as required

Supply Installation Testing and commissioning of Shielded CAT6a twisted pair Cable (STP), complete as per specification & accessories as required

Audio and Visual : Supply, Installation, Testing & Commissioning of 10000 lm 9500 ANSI lumens or above, One DLP laser projector, 3,000,000:1 On/Off contrast ratio upto 20000 hours lamp life with 50% brightness, llumination type Laser phosphor. With zoom lens to project an image size of 135" x 216" from distance of 18mtr to 29mtr Brightness uniformity 95% Aspect ratio 16:10 Optical lens shift Vertical between -100% to +130%, depending on lens Motorized zoom and focus (with lens memory on TLD lenses) Light source lifetime 25,000 hrs Picture-by-picture Two sources simultaneously Inputs Single HDBaseT; HDMI2.0 (HDCP2.2, HDR10); DP 1.2 (HDCP 1.3); Quad 3G/12G SDI / 3D support, Inputs: 2 x HDMI 2.0, 1 x HDbaseT, 1 x DVI-D, 1 x 3G SDI. Controls: RS 232/ Ethernet, 360 deg orientation. Should be supplied with appropriate lens as per site conditons. complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of Projector Zoom Lens complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of Heavy Duty Projector Ceiling Mount with Micro adjustment with customised fabrication complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of Custom fabrication for projector mount installation complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of Providing and fixing of Cyclorama screen 26' x 16' (363" diagonal) with projection image size of 135"X216" (255" diagonal), mattewhite perforated with screen gain complete with eyelets on cyclorama frame on MS pipe, the cyclorama frame is to be fixed on complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of 55 inch LED display, UHD , 350 nits- 4K Resolution, Brightness- Min 350 nits , Contrast- 3000:1 , Viewing Angle – 178/178, 16:9 Aspect ratio, min. 2 x HDMI , 1-USB, Inbuilt/ external wifi/ Bluetooth , 1- RJ 45 , 1- Audio in & out, and 1-RS 232/IR Interfaces, inclusive of all mounting bracket. makes- Harkness hall

Supply, Installation, Testing & Commissioning of Confidence cart for above display

Supply, Installation, Testing & Commissioning of 55 inch LED display, UHD , 350 nits- 4K Resolution, Brightness- Min 350 nits , Contrast- 3000:1 , Viewing Angle – 178/178, 16:9 Aspect ratio, min. 2 x HDMI , 1-USB, Inbuilt/ external wifi/ Bluetooth , 1- RJ 45 , 1- Audio in & out, and 1-RS 232/IR Interfaces, inclusive of all mounting bracket for VIP & Green room. makes- Harkness hall

Supply, Installation, Testing & Commissioning of Digital Podium- Sleek Digital Podium built in Metallic Frame and Wooden Top with built-in 22" Interactive Panel (Electromagnetic Technology) with annotation feature. Podium should have Motorized Tilting, Motorized Height Adjustment of the Podium as per user height, Built-in Connectivity for HDMI, VGA/DVI, USB, 2x 10Amp Power for External Laptop at the Top, Space to place CPU. Podium touch monitor shall have built in annotation feature. complete job.approved brand and iso certified.

Supply, Installation, Testing & Commissioning of Wallplate with HDMI, VGA and USB-C makes- atlona or equivalent

Supply, Installation, Testing & Commissioning of PTZ cameras- Full HD/1080p, PTZ Camera for presenter capturing having minimum 20 x optical zoom, minimum 60 presets and minimum output- 1 x HDMI or HD-SDI or OEM specific output, 1 x RS- 232/422 for control. However, if supported output format is other than HDMI, same shall be converted to HDMI using suitable interface unit or cable convertor. along with the ceiling mount for PTZ Camera. complete job.approved brand and iso certified.Make: GVD/PELCO/AXIS

Supply, Installation, Testing & Commissioning of Ceiling mount for PTZ camera complete job.approved brand and iso certified. Make: GVD/PELCO/AXIS

Supply, Installation, Testing & Commissioning of Joystick controller for PTZ camera complete job.approved brand and iso certified. Make: GVD/PELCO/AXIS

Supply Installation Testing and commissioning of HDMI to USB video capture recorder- HDMI and Audio to USB Scaling Bridge- 4K60 HDMI to USB3.0 Capture Device. Shall support HDMI video input resolutions up to 4096×2160p@60 4:4:4. HDR, and 10-bit per channel Deep Color support. Outputs resolutions up to 3840×2160p@30fps (NV12, I420) or 1920×1080p@60fps (YUY2, P010) Shall support Embedded Audio.

Supply Installation Testing and commissioning of All in one PC- Desktop PC with Intel Core i7 or higher with min. 8GB of RAM DDR4, 500GB SATA hard drive, 10/100/1000 Mbps Ethernet Network Interface Card, and inclusive of 21" HDMI LED monitor with mounting accessories and customization for flush mounting in furniture. It shall be supplied with Licensed Operating System Windows 10 or above, Microsoft Office latest version, USB wireless Keyboard, USB wireless Mouse, minimum 1 x USB2.0 spare port makes- dell/hp

Supply Installation Testing and commissioning of Visualiser- Full HD/ 4k, Table Top Mountable Document Camera with minimum 14x optical zoom — 1 x HDMI or DVI output. DVi models shall be acceptable with external DVi to HDMI convertor interface unit or cable.

Switching System: Supply Installation Testing and commissioning of 8x8 + 4 4K60 HDMI Matrix Switcher. Shall have 4K60 4:4:4 Support and pixel-for-pixel video reproduction of 4K60 source video with full 4:4:4 color space. HDCP 2.2 Support– Support the latest source devices, Mirrored HDBaseT Outputs directly to a display or projector that supports standard HDBaseT,Audio De-embed capabilities. Shall support Twisted Pair Cable Length Up to 262 ft. (80 m) for full 4K signal support and Up to 328 ft. (100 m) for 1080p, Shall have HDMI Input (8) HDMI Type A Female Connector, HDMI Output (8) HDMI Type A Female Connector , 1x LAN10/100 Ethernet Port RJ-45 Connector, TCP/IP Port , HDBaseT Output (4) RJ-45 Connector , IR RX (4) 3.5mm Mini-Stereo Jack , Analog Stereo Output (8) 3 Position 3.5mm pluggable Phoenix Terminal Block, RS-232 Pass-through (4) 3 Position 3.5 mm pluggable Phoenix Terminal Blocks ,RS-232 Matrix (1) DB-9 Connector, Control (1) DB-9 Connector,IR Ext, . (1) 3.5 Mini-Stereo Jack, Compatible Formats HDMI , HDCP, Signal Type Support HDMI, DisplayPort++ (input only with HDMI cable adapter. Input Video Level: .5 - 1.2 V p-p. Data Rate (Max) 18 Gbps. Pixel Clock (Max) Up to 600 Mhz. Audio Format Support: 2 CH L-PCM. HDCP Support Yes HDCP 1.4, 2.2. CEC Support Yes Automatic. Supported Signal Styles Digital video, audio, bidirectional control. Transport Layer Throughput (Max) 10.2 Gbps. makes- atlona or equivalent

Supply Installation Testing and commissioning of 4K60 HDBaseT Receiver and Scaler. 4K60 Support with Built-in Scaling – Experience pixel-for-pixel video reproduction of 4K60 source video. Scaling :Automatically converts signals up or down to match the resolution of the display. HDBaseT Support – Uses the global standard for transmission of ultra-HD A/V, Ethernet,controls, USB and up to 100W of power over a single, long-distance cable. Twisted Pair Cable: Length Up to 262 ft. (80 m) for full 4K signal support, Up to 328 ft. (100 m) for 1080p and below. HDBaseT Layer Throughput (Max) :10.2 Gbps . Connectors : 1x LAN10/100 Ethernet Port, HDBaseT Input (1) RJ-45 , 1x IR RX 3.5mm Mini-Stereo Jack, 1x IR TX 3.5mm Pluggable Phoenix Terminal Block ,1x HDMI Output HDMI Type A Female, 1x Analog Stereo Output 3 Position 3.5mm pluggable Phoenix Terminal Block , S/PDIF Digital Audio Output RCA Jack , Serial 3 Position 3.5mm Pluggable Phoenix Terminal Block ,Bidirectional RS-232 . Compatible Formats HDMI , HDCP. Signal Type Support HDMI, DisplayPort++ (input only with HDMI cable adapter). Output Signal Type : HDMI. Output Scaling Auto or Manual. Data Rate (Max) :18 Gbp (Output). Pixel Clock (Max) Up to 600 Mhz (Output) 300 Mhz (Input Signals). Audio Format Support 2 CH L-PCM. HDCP Support :Yes HDCP 1.4, 2.2. CEC Support: Yes Automatic. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 4K60 4:4:4 Video Scaler. Configured to automatically scale to the optimal resolution of the display based on its EDID. Can also be set to always scale to a particular resolution. Should have DIP switches for scaler configuration / setting the resolution. Should have 3 Position 3.5mm Pluggable Phoenix Terminal Block,. Bidirectional RS-232. complete job.approved brand and iso certified. equivalent

Supply Installation Testing and commissioning of 4K60 HDMI Twisted Pair Transmitter Module. Shall be capable to distributes full 4K60 4:4:4 video end-to-end securely as well as audio, control, Ethernet, and USB 2.0 over one shielded Cat6, Cat6A or Cat7 standard twisted pair cable. Shall support High Dynamic Range (HDR) and Deep Color (24-bit, 30-bit, 36-bit ), High-speed USB 2.0 data from devices like web cameras and storage devices are transmitted without the need for separate cables. Transport Layer Throughput (Max) :10.2 Gbps. Video Data Rate (Max) :18 Gbps. Video Pixel Clock (Max) 600 MHz. Twisted Pair Cable Length :Up to 100m (328 ft). CEC Support,EDID Support. Regulatory Compliance: FCC,UL 62368-1,UL 60950-1,RoHS/REACH/WEEE. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 4K60 HDMI Twisted Pair Scaling Receiver Module. Shall be capable to distributes full 4K60 4:4:4 video end-to-end securely as well as audio, control, Ethernet, and USB 2.0 over one shielded Cat6, Cat6A or Cat7 standard twisted pair cable. Shall support High Dynamic Range (HDR) and Deep Color (24-bit, 30-bit, 36-bit ), High-speed USB 2.0 data from devices like web cameras and storage devices are transmitted without the need for separate cables. Transport Layer Throughput (Max) :10.2 Gbps. Video Data Rate (Max) :18 Gbps. Video Pixel Clock (Max) 600 MHz. Twisted Pair Cable Length :Up to 100m (328 ft). CEC Support,EDID Support . Regulatory Compliance: FCC,UL 62368-1,UL 60950-1,RoHS/REACH/WEEE. makes - atlona or equivalent

Supply Installation Testing and commissioning of Recording and Streaming Hardware Shall be able to do recording and streaming simultaneously 2 or more-Channel recording, streaming, live switching media processor Supports 1080p 60/30fps recording Can record upto any two or more inputs simultaneously in a single frame and as well as individual sources simultaneously Should have minimum 1TB inbuilt storage Should be able to stream at 2 or more different clouds simultaneously Built-in minimum 2 Inputs (HDMI /IP/3G-SDI/DVI) HDMI Out for Preview complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of HDMI and Audio to USB Scaling Bridge- Supply Installation Testing and commissioning of 4K60 HDMI to USB3.0 Capture Device. Shall support HDMI video input resolutions up to 4096×2160p@60 4:4:4. HDR, and 10-bit per channel Deep Color support. Outputs resolutions up to 3840×2160p@30fps (NV12, I420) or 1920×1080p@60fps (YUY2, P010) Shall support Embedded Audio. complete job.approved brand and iso certified.

Supply Installation Testing and commissioning of 4K HDMI Decor Style Wallplate Transmitter. Should send HDMI/HDCP, along with embedded audio up to 80 meters over one shielded Cat6A or Cat7 standard twisted pair cable. Shall support 4K and Ultra High Definition (UHD). Transport Layer Throughput (max) 10.2 Gbps. Video Data Rate (max) :8.91 Gbps. Video Pixel Clock (max) :297 MHz. Shall Support 3D Format. Audio Sample Rate: 32 kHz, 44.1 kHz, 48 kHz, 96 kHz, 192kHz Regulatory Compliance: UL 60950-1 2nd Ed. Am2,RoHS,WEEE. it should be supplied along with the PoE Injector complete job.approved brand and iso certified.

Audio System: Supply Installation Testing and commissioning of FOH-High Power Full Range 15" Loudspeaker with driver ensures high power output with high sensitivity and exceptional efficiency, Frequency Response (-3dB) 70 Hz - 25 kHz, Frequency Range (-10 dB) 70 Hz - 25 kHzr or better 75º dispersion for optimum coverage, System Sensitivity Passive-99 Db ,LF-100 dB,HF- 106 dB, SPL 126 dB or more(direct and total SPL sholud not very more then ±3 db) ,should be capable of achieving RT value of 1.12@500 Hz and STI should be 0.6 makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Mounting arrangement for FOH Speakers. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Delay Fill-Full Range Passive 12" Loudspeaker wit , Frequency Response (-3 dB) 70 Hz - 25kHz or better,Frequency Range (-10 dB) 55 Hz - 38 kHz, Sensitivity 97 dB, SPL 120 dB or Average 126 dB (direct and total SPL sholud not very more then ±3 db) Peak, 80° ~ 90°dispersion for optimum coverage,multi-purpose sound reinforcement loudspeaker, capable of achieving RT value of 1.12@500 Hz and STI should be 0.6makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Mounting arrangement for Delay Speakers.

Supply Installation Testing and commissioning of Sub Woofer-High Output Low Profile 2 x 12" Subwoofer delivering 800 W rms @ 4 ohms,Low distortion dual port design for maximum sound pressure levels, Frequency Response (-3 dB) 50 Hz - 160 Hz, Frequency Range (-10 dB) 35 Hz - 200 Hz, handles ergonomically integrated into rear of cabinet,Sensitivity minimum 95 dB or better, SPL 129 dB or more.

Supply Installation Testing and commissioning of Mounting arrangement for Subwooofer makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Front Fill- 6"Loudspeaker with power handling capacity of 60 W, high durability design for constant heavy usage in demanding applications, Frequency Response (±3 dB) 75 Hz - 22 kHz, 55 Hz - 30 kHz Frequency Range (-10 dB), Sensitivity 90 dB, 90 degrees conical nominal coverage, SPL 108 dB average and 114 dB peak, Transformer Taps 70 V: 60 W / 30 W / 15 W / 7.5 W , 100 V: 60 W / 30 W / 15 W. Yoke bracket included. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Stage Monitor : 2 Way 12" Stage Monitor with Low profile design to maximise audience sight lines, Class-D with 1 x 12" LF driver,1 x 1" HF compression driver, Frequency Response (±3 dB) 75 Hz - 18kHz, Frequency Range(-10dB) 68Hz – 20kHz, Low distortion rotatable waveguide provides 60° H x 40° V dispersion, Maximum SPL 125 dB peak, Fully featured user interface.

Supply Installation Testing and commissioning of Control Room Speaker: Loudspeaker with power 25 W RMS or more, Adjustable equalization with SPL 101 dB or better, Dispersion : 90°, Frequency response 56 Hz to 48 kHz, Accurately tuned front-firing bass port allows near-wall placement and ensures optimal low frequency performance with all complete accessores. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Green Room Speakers- 5" Loudspeaker with RMS power handling capacity of 50 W , IP65 rating, Frequency Response (±3 dB) 90 Hz - 18kHz or better, Frequency Range (-10 dB) 80 Hz - 30 kHz, Sensitivity 88 dB, Nominal Impedance 16 ohms, SPL 105 dB or better and Transformer Taps 70 V: 30 W / 15 W / 7.5 W / 3.75 W , 100 V: 30 W / 15 W / 7.5 W, Yoke bracket included. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of The Amplifier should have Four Channel 2000 Watt Energy efficient Power Amplifier delivering 4 x 500 Watts into 4 Ohms, 4 x 500 Watts into 8 Ohms,Signal-to-noise ratio :>106 dBA makes- tannoy, bose and martin

Supply Installation Testing and commissioning of The Amplifier should have 2-Channel 2400 W power with Integrated DSP delivering, The unit shall include comprehensive digital audio processing configured specifically for loudspeaker drive applications. In discrete two-channel mode, each amplifier channel shall deliver maximum continuous power, THD + N 20 Hz- 20 kHz for 1 W <0.01%, Signal-to-Noise ratio >100 dB or more, Frequency Response 2 Hz- 42 kHz, Common Mode Rejection 50 dB, Networked control. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of The Amplifier should have 2-Channel 1200 W power with Integrated DSP delivering, The unit shall include comprehensive digital audio processing configured specifically for loudspeaker drive applications. In discrete two-channel mode, each amplifier channel shall deliver maximum continuous power, THD + N 20 Hz- 20 kHz for 1 W <0.01%, Signal-to-Noise ratio >100 dB or more, Frequency Response 2 Hz- 42 kHz, Common Mode Rejection 50 dB, Networked control. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of The amplifier shall be flexible power scheme with seamless and automatic power on/off based on the input signal, which reduces consumption when a signal is not present, Should have dual channel 120 Watt Amplifier with delivering 120 W, Front panel power control button for direct access, Rack-mountable 1U, half-rack width enclosure with joining brackets for rack, distortion <0.05%, Frequency response 20 Hz to 20 kHz or better, Signal-to-noise >97 dB or more. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Wireless Handheld Microphone: Wireless Cardioid condenser handheld set with Remote Receiver Connector RJ45, Frequency Response of 20 Hz to 20 kHz or better, Operating Range 60 m or more, Dynamic Range > 109dB or more, on/off switch, RF Power Output High 60 mW, Multiple band with 10 channels on each band maximum Output level, Rack-mount receiver chassis,handheld dynamic unidirectional microphone.

Supply Installation Testing and commissioning of Dual Channel wireless Lapel Microphone: Wireless Cardioid condenser Lapel microphone with Remote Receiver Connector RJ45, Frequency Response of 20 Hz to 20 kHz or better, Operating Range 60 m or more, Dynamic Range > 109dB or more, on/off switch, RF Power Output High 60 mW, Multiple band with 10 channels on each band maximum Output level, Rack-mount receiver chassis,handheld dynamic unidirectional microphone. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Vocal Handheld Microphone: Hypercardioid dynamic Neodymium handheld microphone with Frequency Response of 60 - 14,000 Hz, Open Circuit Sensitivity -54 dB (1.9 mV) re 1V at 1 Pa , Impedance-600 ohms , on/off switch, Integral 3-pin gold-plated XLRM-type connector, Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen

Supply Installation Testing and commissioning of Instrument Microphone : Handheld microphone with Frequency Response of 60 - 14,000 Hz, Open Circuit Sensitivity-54 dB, Impedance-600 ohms, on/off switch, Integral 3-pin gold-plated XLRM-type connector, Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen. For Tabla / Shenai / Kanjira Instrument makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Instrument Microphone : Instrument microphone with Frequency Response of 80 - 20,000 Hz, Open Circuit Sensitivity 46 dB, Impedance-200 ohms , on/off switch, Integral 3-pin gold-plated XLRM-type connector, Rugged all-metal construction complete with stand clamp and threaded adaptor and Foam Wind Screen. For Bansuri / Sitar / Veena / Sarod / Tambora / Harmonium Instrument makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Gooseneck microphone with table stand : Gooseneck Microphone with Frequency Response 30-18,000 Hz or more, Impedance 250 ohms or better, Maximum Input Sound Level 139 dB SPL or more better, Anti-Shock Microphone Stand with on/off Switch. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Digital Mixer Compact 40 or more input, Digital Mixing Console with Powerful scene management for convenient handling, Channel LCD's, 32-Channel or more, Audio Interface and remote Control, 8 XLR outputs plus 6 additional line in/outputs, a talkback section with integrated or external mic, High-resolution 7" day-viewable Color TFT , Main LCR,and full dynamics processing, plus 8 DCA and 6 mute groups. makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Stage Rack I/O Box with 16 Remote-Controllable Preamps, 8 Outputs, Precise LED metering plus 7-segment displays for signal control on stage, Dual ADAT outputs providing 16-channel digital output on two optical connectors, In/Out for bi-directional communication.makes- tannoy, bose and martin

Supply Installation Testing and commissioning of Floor junction box with 3 x XLR balanced input and 1 x XLR Balanced line output makes- tannoy, bose and martin

MGPS : PART-A: GAS PLANT EQUIPMENT: MEDICAL AIR COMPRESSOR SYSTEM, having reciprocating oil free compressor with foundation, Filtration system, receiver, electrical connection from compressor to control panel and all as required as per specification. Entire system shall be installed as a package and compatible to fulfil the demand of system. Product should be as per specification. Make- Hitachi/ Anest-Iwata/Atlas-Copco/ IR

SITC of MEDICAL VACUUM SYSTEM. The system shall consist of Rotary Vane Vacuum pumps (including civil foundation, skid and electrical wiring of suitable capacity from Pump to electrical panel and non-return valve complete) with suitable hp motor. The vacuum pump, motor and associated accessories shall be installed as a package by the manufacturer/installer, and not as discrete items. Complete system is as per specification. Make- Busch/IR/Atlas Copco/ Edward/Gardner Denver.

SITC of OXYGEN MANIFOLD minimum of 2 x 10 cylinders oxygen manifold extendable type with middle frame along with tail pipe, having top frame comprising of high-pressure copper pipe with high pressure brass fitting made of high tensile brass, NRV. 1x10 bank shall as primary and other 1x10 shall be as reserve source of oxygen supply. It shall automatically supply the pipeline when primary source becomes exhausted or fails due to any reason. The system shall have source shut-off valve for easy changing and positioning, without hook. The cylinder should be placed with the help of cylinder brackets and fixing chains which should be zinc plated appropriate. (Gas cylinders are not in the scope of this work). Product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

S.I.T.C of Imported CE Marked compliant with HTM or NFPA Oxygen Change-Over Reduction Box (Automatic Control Panel) of Digital fully Automatic type, capable of switching from “Bank in Use” to “Reserve Bank” without fluctuation in delivery line pressure and without the need for external electrical power. The Changeover panel shall be rated for min. 180 QMH at 400 kPA, and shall include the following accessories. Panel shall comply with HTM/ISO as per specification. Make- Allied/ Medicop/ Drager/Ohio

Oxygen Emergency System (4+4): - The oxygen emergency system contains 8 nos. Gas cylinder manifold along with copper header, Brass Non-Return valve & High-pressure copper tail pipe for each cylinder complete. product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

NITROUS OXIDE SUPPLY SYSTEM: SITC of NITROUS OXIDE MANIFOLD SYSTEM minimum of 2x4 cylinders and reserve source of nitrous oxide will be 1x4 cylinders. Cylinder size shall be as given in the drawings having top frame comprising of high-pressure copper pipe with high pressure brass fitting made of high tensile brass, NRV, high pressure copper tailpiece made of high-pressure copper. Reserve source of N2O shall automatically supply the pipeline when primary source of supply become exhausted or fails due to any reason. (Gas cylinders are not in the scope of this work). Product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

S.I.T.C of Imported CE marked Nitrous Oxide Change-Over Reduction Box (Automatic Control Panel conforming to HTM/ ISO ) of Digital fully Automatic type, capable of switching from “Bank in Use” to “Reserve Bank” without fluctuation in delivery line pressure and without the need for external electrical power. The Changeover panel shall be rated for min. 50 QMH at 400 kPA, and shall include the following accessories. Product should be as per specification. Make- Allied/Medicop/Drager/Ohio

Nitrous Oxide Emergency Manifold: - The Nitrous Oxide Emergency system contains 2 Nos Gas cylinder manifold along with copper header, Brass Non-Return valve & High-pressure copper tail pipe for each cylinder and one number of high-pressure regulators. product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

Plant Master Gas Alarm: - Imported CE marked (with CE Number) Master Gas Alarm for 4-gases conforming to HTM/NFPA. This panel shall be able to test Short Circuit Fault, Open Circuit Fault, Source Equipment Fault and include the a) Dual Circuit LED Indicators. b) Test facility to check LED c) Test facility to check LED Integrity. Panel shall be equipped with Micro-processor-based alarm. product should be as per specification. As per approved make attached.

Combined Electrical Control Panel for Medical Air Compressors & Vacuum Pumps as per specification with all required support foundation complete

PART-B (GAS DISTRIBUTION EQUIPMENTS): Terminal Outlets: - Terminal Outlets gas specific for the services indicated (viz. O2, Air & Vacuum) and to accept only compatible quick connect Pin/Geometric Index type adapters as HTM/NFPA standard, CE Certified/UL Listed as per drawings and as required. product should be as per specification. Make- Allied/Medicop/Drager/Ohio Oxygen Outlet

Vacuum Outlet

MA-4 Outlet

SA-7 Outlet

Nitrous Oxide Outlet

Suitable Gas Outlet Adopter compatible with required ward Accessories made from stainless steel as per current latest standard. Oxygen Outlet

Vacuum Outlet

MA-4 Outlet

SA-7 Outlet

Nitrous Oxide Outlet

2 Services (Oxygen, Vacuum)

3 Services (Oxygen, MA-4, Vacuum)

5 Services (Oxygen, MA-4, MA-7, Nitrous Oxide, Vacuum)

Modular bed head panel, with provision of gas outlet, electrical, 900 mm long, double compartment seperate for gases and electrical, made of high grade of aluminium. Fabricated by extrusion method and powder coated as per approved colors.as per specification and drawing Make- Altos/Sigma Meditech/ Medimatic/GM Medical

Copper Piping: - copper pipes, for Medical Gases, complete with elbows, flanges, specials, others fittings, and steel supports. The copper pipe should be of solid drawn seamless deoxidized, un-arsenical, tempered and of degreased material conforming to BS-EN 13348/ASTM B819, of copper pipe. must be certified and inspected by third party inspection agency like LLoyds/SGS/TUV etc.Make- Mex Flow/ Mandev/Metallaco/Janya

Isolation valve - All valves are to be ball valves type and PTFE or Teflon seals. They shall be suitable for a working pressure of 10.2 Kg/cm² gauge. Valves shall be fitted into the pipeline by means of capillary hard soldered joints containing silver. it should be open/close with help of handle with rotation of 90 degree. Make- RN/RB/Lrgris/Matrix/ CIM

PART-C (MEDICAL GAS PIPELINE SYSTEM ACCESSORIES): Oxygen Flow Meter - Made from brass, chrome plated. It shall be back pressure compensated type having housing of Polycarbonate autoclavable reusable flow range 0-15 LPM. Fitted with matching adopter for oxygen outlet point and humidifier shall be compatible with flowmeter and reusable and as per specifications and as required. Product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

SUCTION UNITS: Ward Vacuum Unit - Regulator capable of controlling vacuum between 0 to 760 mm Hg and Polycarbonate autoclavable, reusable type receiver jar of not less 600 ml. Vacuum regulator shall have a dial gauge, on/off switch, valve control knob and as per specifications and as required. Product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

Low pressure suction tube for suction outlet adopter as required

Operation Theatre Suction Trolley- having 2 Nos. 2000 ml receiver jars of Polycarbonate autoclavable up to 121 *C, reusable and mounted on trolley with wheel arrangement. The trolley shall have one number of vacuum regulators having regulation control between 0-760 mm Hg and interconnecting suction tubes. Product should be as per specification. Make- Medimatic/ Sigma Meditech/ Mediasha

Modular operation theatre: Stainless Steel 304 Grade min. 1.5mm thk Pre-Fabricated Modular Operation Theatre Wall Panel and Ceiling panel backed with 12mm thick. Gypsum with proper supports as per specification. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline /Medimatic

Filling of Joints ,Cavity and Antibacterial painting:- Filling of all joints & cavities with epoxy filler, sanded flush for seamless finish with one primer and three coats of antibacterial & antifungal paint . That is equivalent to a dry film thickness of 300 microns.

Hermetically Sealed automatic sliding doors:- Automatically Operated hermetically sealed Sliding Doors of different size as required with glass vision window of 300mm x 300mm (WXH) along with all required accessories and in colour approved by client as per specification. Make- Metaflex/Riboon/SHD /Altos Door size 1500 mm X 2100 mm

Door size 1000 mm X 2100 mm

Laminar airflow System: - Laminar Plan air Ceiling system of size (2400mmx2400 mm) with unidirectional airflow with "S" class HEPA filter with an efficiency 99.97% down to 0.3 micron. The holding structure & top plenum are made up of Aluminium Sheet with a thickness of 1.6mm. It should be sealed with gasket conforming to DIN 4799 standards for the air distribution system. 2 layer diffuser with monofilament precision woven polyester of uniform porosity with an open area of sufficient resistance to create laminar from diffusers face and integral lighting provides an illumination level in excess of 15000 Lux in operating area and 10000 Lux other with flicker less digitally controlled steeples dimming down to 5%. Make- Altos/ Sigma Meditech/ Shree anand/ Digiline/Medimatic

Electrical wiring - Electrical wiring within the OT Area, conduit pipes and electrical switch & Socket with Electrical Distribution board for Operating room with MCB's and Relay cards. All wiring should be done through ISI mark copper wire only with conduit pipe..

Peripheral lights:- Recess mounted IP 54 protocol, non-hygroscopic Peripheral Lights for clean room application. Each light set having 2 nos of 36-watt fluorescent lamps with digitally controlled dimmable ballast. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic

Scrub Sink: - scrub sink made out of 304 graded brushed finished stainless steel, with photo electric sensors,1 No. Mixture valve, 2 nos. solenoid valves with Foot operated switch as per specification. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic Scrub Sink 2 - bay.

Writing board:- It should be flush mounted with a sterile jointing system, 1.50mm thick, white Ceramic board, bonded to a 2 mm steel sheet for additional rigidity. Approximate size of the same should be 940 x 600 mm. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic

X-ray view box:- Twin Plate X-Ray viewing screen with flicker free dimming light range from 15 to 100% with complete accessories as required to view the X-ray film. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic

Control Panel:- Touch Panel type Operation Theatre Control Panel (6 service Tiles) mounted. Flushed in the theatre wall with complete distribution board with all accessories. Make- Altos/ Sigma Meditech/ Shree anand/ Digiline/Medimatic Following are the controls/display available:-

Dirty Hatch box:- Dirty hatch box made up of Stainless steel grade 304, having two doors on both side. One door will be opened at one time , indicator on both sides in case of door is open. The hatch will be designed in such a way that only one door will be opened at one time. The UV light will glow when both the doors are in closed position. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic

LED Operating light: - Ceiling mounted Operating room Dual Dome Light CE Notified and US FDA approved with provision of camera in it. 160000 Lux + 120000 Lux and o Colour rendering index CRI>95 and R9 ≥ 91 to 97 as per specification. Make- Drager/Steris/Luvis/Maquet

Ceiling Pendants:- Ceiling Pendent with weight carrying capacity of 100Kg. The pendant should have 10-12 electrical sockets, one monitor shelf and instrument Drawer IV Pole and infusion Pump Rod mount on it. system must be CE notified or US FDA approved for quality parameter. Gas outlets for pendants will be provide by user/department for compatibility with hospital wards. for connection of gases to pendant required copper pipe point near to pendant will be provide by department/MGPS contractor. Make- Berman/Silbermann/Luvis/Drager/Becon Meades Double Arm surgeon pendant

Single Arm Anaesthesia Pendant

SITC of Pressure relief damper:- Pressure Relief Damper. Made up of 304 graded stainless-steel blades with all required accessories. It opens to maintain balanced positive pressure inside OT and prevent air contamination from outside. Make- Altos/ Sigma Meditech/ Shree Anand/ Digiline/Medimatic

Storage Cabinet:- Equipment Storage Unit is to be provided in operating theatre of dimension approved in the user. Approximate size of the unit should be 860(W) x1660(H) x350(D) mm and it should be flush mounted into the theatre wall with a sterile jointing system. Make- Altos/ Sigma Meditech/ Shree anand/ Digiline/Medimatic

Anti - Static flooring:- 2mm thick Anti static, conductive dissipative flooring tile laid on a semi conductive adhesive base resistant to mechanical stress and dynamic load and washable. Its include all required flooring and levelling work for proper sloping of OT floors. it should be finished with proper sealed coving with wall to prevent water leakage in flooring at time of wash.

Medical Gas pipeline system: inside OT FOR Medical Gases including all fitting and fixtures, that all pipes should be tapped through main corridor medical gas pipes by only the main medical gas services contractor. etc complete as required as per specification.

5 Services (Oxygen, MA-4, MA-7, Nitrous Oxide, Vacuum)

online ups of capacity 10 KVA with 30 min Backup as per specification Make- Numeric/3EM/UTL/Microtek

View window with motorized blind of size min 1m x1m completely sealed Make- Altos/ Sigma Meditech/ windowtech/ Digiline

Supply and Installation of Multi 'B' Rollformed 30B/80B/130B/180B aluminium plain panel ceiling approved colour consisting of panel 30mm x 0.5mm x 15mm, 80mm x 0.5mm x 15mm, 130mm x 0.5mm x 15mm & 180mm x 0.6mm x 15 mm of length minimum of 5mtr and max up to 6 mtr, Coil Coated on a Continuous Paint Line in approved colour, double baked and roll formed from enamelled corrosion resistance Aluminium alloy (AA3105 / 3000 series) for higher strength and good roll forming characteristics.The Multi B Panels shall be manufactured on high speed, high precision roll forming machine with Hi configuration roller leveling process to ensure the flatness and to avoid the failure of metal at corners. The coil is coated on a continuous paint line double baked and shall be stove enamelled in a continuous coil coating process of approved colour on the exposed side and the reverse side with polyester primer. Panel shall be clipped to a baked enamelled Aluminium multi panel carrier of 62mm wide x 29mm deep made of 0.95mm thick in standard length of 5 mtrs made of doubled baked enamelled Aluminium alloy in black colour with cut outs to hold the multi size panels in same carrier with a module of 50mm, 100mm, 150mm and 200 mm (width of gap 20mm without recessed profile) and at a distance 1200mm. The Carrier shall be suspended by means of G.I. suspension rod 4mm diameter, and a Galvanised suspension spring clip at a distance of 1.5mtrs centre to centre. The ceiling system should meet the required standards for GreenPro certification and should qualify as green product as per CII green products and services council. The manufacturer should be ISO 9001:2015 Quality Management System Certification compliant with in house testing facility and should have their own manufacturing plant with Roll forming machine in India. Mode of Measurements: Measurements shall be wall to wall without any deductions for lights, diffusers, columns, etc. Approved make List: Lindner, HunterDouglas, SAS, Gordon, DAMPA

Supply & Fixing of Green Pro Certified G.I Torsion Spring Plain Ceiling System comprising of Tile of 600mm wide and 600mm llong manufactured out of 0.5mm thick G.I Plain. The metal ceiling panels shall be downward accessible with a minimum of four (4) torsion springs per panel. The Tile will be manufactured on advanced CAD/CAM equipment that includes several stages of manufacturing process, and special process of six roller sheets leveling to achieve flat panels. Torsion Spring panel with two side legs die formed and two end legs die formed and punched to receive torsion springs (min two springs each end or side) for secure engagement into Tee Grid main runners which are factory punched to receive torsion springs. Tiles will be square edged. The metal ceiling panels shall be downward accessible with a minimum of four (4) torsion springs per panel. The Tile shall be Coil Coated or Polyester powder coated in approved color. Panel will be pre-treated in latest nano technology process and electro statically powder coated with automatic corona system and cured with gas catalytic technology. All ceiling shall be Green pro Certified: For LEED certification by Indian Green Building council (IGBC). Ceiling manufacturer should have in-house testing lab and powder coating line (with Nano Technology & Catalytic Converter) in India. Metal ceiling Tested for Seismic Zone V compliance as per IS 1893-part 1-2016. Main Runners: 24mm deep, inverted “Tee” sections, 3.6m long, with factory punched flanges to receive torsion spring assembly. Main Tee on center spacing to match panel length. Cross Runners: 24 mm deep, inverted “Tee” sections designed to interlock in to web of main tee section on designated spacing. Cross tee length to match panel length. Cross tees are spaced spacing 1200mm on center maximum.Suspension System: As per manufacturer standard considering type of plenum and its height. Approved Make List: Lindner, Hunter Douglas, SAS, Gordon, DAMPA. statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

CURTAIN, CURTAIN TRACK HOSPITAL: Curtain Track G RAIL 4100-(including all accessories) strong functional and fully reversible profile confirming to HTM66, synthetic wall and ceiling brackets complying with the European NEN 1010 standards, made of aluminium 606035- T6 –F2. Shape and size tolerance in accordance with DIN 17615. White powder coating colour RAL 9010, in accordance with Qualicoat standard. Runner/Glider hooks made of nylon 6.6 with SS 304 grade hooks. Profile weight must be 394 g/m. The system is such that if required can be mounted with ANTI-LIGATURE load release components, to provide a controlled system collapse as per NHS guidelines. Approved make : JDV Healthcare, Prime Technomed Solutions & Window Techs

CUBICLE / PRIVACY CURTAIN : Curtains fabric to comply with many safety protocols it must be stain retardant and has a coating of antimicrobial and fire retardancy effect,must be certified according to international standards , must be certified by indian govt approved laboratories . it has to contributes to the reduction of transferring bacteria, help in increasing/improvement of hygienic standards provide greater safety against infection .No need of sterilization after wash. The antibacterial component facilitate in reducing the growth of fungi, moulds and mildew that can develop in any type of an indoor environment. Effective after 100 washes and , Antibaterial activity must be tested accourding to the JIS L 1902:2015 & Antimicrobial Acitivy must be tested according to AATCC 100-2019 from goverment approved lab. Fire Retadency test must be done by lab linked to ministry of textile, goverment of India according to NHPA 701. Approved make : JDV Healthcare, Prime Technomed Solutions & Window Techs

WALL GUARD : The system fixed to brick wall at 900mm center high from finished floor level comprising continuous aluminum rail retainer, 2 impact absorbing strip, end cap and high impact vinyl acrylic snap-on textured surface cover. The wall guard must be 152mm wide, as specified by the client , must have 1.5 mm thick aluminum retainer, must have 2 mm thick scratch and stain resistance rigid vinyl cover, should be coated with antifungal and antibacterial chemical. the system shall be designed to withstand impact and provides a cushioned surface with its integrated rubberized absorber, making it ideal for areas like high traffic corridors, loading bays and light cargo lifts. the vinyl cover should be fire retardant according to the norms and should have test certificates of that. it must be according to ROHS compliances. The material should come the ROHS certification from govt approved lab. texture to provide an anti-slip surface , it should have adjustable end cap , corner joint and adaptor plate .aluminum retainer should be in mill finish and fabricated from 6063-T5 alloy. Approved make : JDV Healthcare, Prime Technomed Solutions & Window Techs

CORNER GUARD : The system fixed to brick wall at the corner from finished floor level. Adjustable end cap. High impact vinyl acrylic snap-on matt finished.. The corner guard must be 50 mm * 50 mm , as specified by the client in size with aluminum retainer and rigid vinyl, must have 1.5 mm thick aluminum retainer, must have 2 mm thick scratch and stain resistance rigid vinyl cover, should be coated with antifungal and antibacterial chemical. the system shall be designed to withstand impact. making it ideal for areas like high traffic corridors and corners. the vinyl cover should be fire retardant according to the norms and should have test certificates of that. it must be according to ROHS compliances. The material should come the ROHS certification from govt approved lab. texture to provide an anti-slip surface , it should have adjustable end cap .aluminum retainer should be in mill finish and fabricated from 6063-T5 alloy. Approved make : JDV Healthcare, Prime Technomed Solutions & Window Techs

NURSE CALL SYSTEM: Supply, Installation, Testing and Commissioning of Master Unit 10 Channels having capability of connecting with 10 Beds as per technical specifications of the Tender

Supply, Installation, Testing and Commissioning of Master Unit 30 Channels having capability of connecting with 30 Beds as per technical specifications of the Tender

Supply, Installation, Testing and Commissioning of Toilet button complying with IP-X5 / IEC60529 as per technical specifications of the Tender

Supply, Installation, Testing and Commissioning of Bed side unit having dimensions of 116 mm x 120 mm connected with IV/ME Unit with cable and Call Button having cord made of Soft Poly Vinyl Chloride resin with 6 PIN Connector as per technical specifications of the Tender

Supply, Installation, Testing and Commissioning of Monitor 15 Inch with Central Processing Unit along with Software for Viewing Data and Patient Layout

Providing and fixing Glass Reinforced Concrete G.R.C. Screens (Jaali) in approved size, pattern, design, thickness 30-50MM and color of specified make. The screens should be made from '53 grade' approved White Portland cement, quartz, fine silica sand, alkali resistant glass fiber manufactured by Saint Gobain or equivalent, polymers manufactured by BASF or equivalent, super plasticizers manufactured by BASF or equivalent with UV resistant synthetic inorganic pigments made by BAYFERROX (Germany) or equivalent. The material casting should be done in synthetic rubber / FRP mould manufactured by 'Reckli' or equivalent. The fixing of screens should be done with galvanized M.S. / S.S.(SS 304) "L" shaped clamps, dash fasteners and pins etc. complete as per requirement, approved shop drawing and instructions.

Providing & fixing of total height of 7-8 mm and pile height of 4-5 mm thick Carpet tile flooring of plie gsm of 700 total gsm of 3800 ,made of 100 % polyfine polypropleyne natural with dual baching, Primary baching with PVC & Secondary withPVR+ fibar glass form approved make in required colours, shades, Complete as per manufacture's specification including cost of special quality adhesive complete fixed in position to the entire satisfaction of engineer in charge.Make : F&F, BVG, Welspun.

Providing & fixing of GYM flooring of EPDM 15mm Laminated interlock rubber flooring with adhesive with complete job.

Providing and laying Laminate wooden flooring (Grade AC5)haringbone pattern 12 mm thick, having a good backing layer made up of plastic laminate or melamine, core made up of High-density fibreboard (HDF),which is less resistant to impact damage and less resistant to being dented by heavy furniture, having a décor layer to give each floor its appearance and consisting of one or more sheets of paper impregnated with melamine resin and top wear layer having clear aluminium oxide finish that protects the decorative layer & imparts the desired level of sheen, from full gloss to low gloss, duly fixed to the base floor using adhesive as approved by the manufacturer/Engineer in charge.Make :Krontex, Haro, Quikstep,floortex.

Providing & fixing of vinyl flooring, 2.0 mm thick multi-application flooring roll in Random marbled Pattern in pastel shades of 1.5mtr width and 20mtr length Heavy duty Homogeneous Hard wearing flooring having 3.2kg/sqm weight, dimension Stability <0.40% as per EN434, Electrostatic properties 10^9-10^10 ohms as per EN1081, Abrasion Resistance Wear Group-T as per EN 649 EN660-2, Classs-1 Surface Speard Flame as per BS476 Part-7, Slip Resistance R-9 as per DIN 51130, Suitable/Continuous use-Bearing a CASTER CHAIR as per EN425, Product having Anti-bacterial / Anti-fungicidal, Anti-dirt surface Properties, Product having SWISSCERT Green Product Certification, Ideal for clean rooms ( ISO Class 5 / Class A ) Solid, Resilient, PUR Wondergaurd surface treatment for ease in maintenance with stain resistance & very easy cleaning of shoe scuff marks. Installed in approved shade as per direction of Engineer-in-charge.Installation: The vinyl flooring sheet should be installed with Adhesive recommended by Vinyl Flooring manufacturer. (SR 505 manufactured by Fevicol). The joints in the flooring should be sealed by using a PVC welding cord of matching colour to be supplied by the manufacturer, using a hot air gun for fusion of welding cord with flooring for seamless installation etc. complete as per direction of Engineer-in-charge.Make LG, Wonder floor, Vibrant

Supply of 2.0 mm thick Non directional ,multi-colour polymer chips, homogeneous Conductive flooring rolls in width of 2.00 mtr and continuous length of 20 mtrs , Surface Electrical Resistance of 5 x 10^4 Ohms to 5 x 10^6 Ohms with black conductive base for better connectivity and in approved design and shade , Installation with laying copper strips on the base floor throughout the floor area as per the design and leaving the edges of copper strip for connecting to the ground bus bar , and considering the wastage after cutting the rolls to fit the floor size and cutting the joints after overlapping for uniformity and further sealing the joints by thermal welding process on a smooth and moisture free levelled floor surface using conductive adhesive Fevicol/aerobond, all complete and as per the instruction of the engineer in charge The vinyl flooring sheet should be installed with Adhesive recommended by Vinyl Flooring manufacturer. (SR 505 manufactured by Fevicol). The joints in the flooring should be sealed by using a PVC welding cord of matching colour to be supplied by the manufacturer, using a hot air gun for fusion of welding cord with flooring for seamless installation etc. complete as per direction of Engineer-in-charge.Make LG, Wonder floor, Vibrant

PART(B) HVAC WORKS GMC & TEACHING HOSPITAL: Supply Installation Testing and Commissioning of Variable Refrigerant Flow air cooled top discharge Outdoor Units suitable for cooling and heating, having all hermetically sealed inverter type Scroll / Twin rotary Compressor, minimum 2 compressors for above 14HP modules, microprocessor based controller, top discharge type condensing units with R410 A refrigerant , vibration isolators with suitable foundation etc. complete as required. The unit shall be suitable to work on 400 V+/-10% 3 phase , 50 Hz AC power supply. The full load COP at AHRI should not be less than 4.0 & IEER not less than 6.5. Make: Carrier/Mitsubishi Electric/Toshiba 60HP

Supply Installation Testing and Commissioning of Variable Refrigerant Flow air cooled side discharge Outdoor Units suitable for cooling and heating, having all hermetically sealed inverter type Scroll / Twin rotary Compressor, microprocessor based controller, Unit should be able to opearte in sub zero/negative ambient temperature upto minus 15 degree centigrade, vibration isolators with suitable foundation etc. complete as required. . Make: Carrier/Mitsubishi Electric/Toshiba 4HP

Supplying, installing, testing and commissioning of Wall mounted type indoor units each complete with coil, filter, etc. Air conditioners with evaporating unit comprising of cooling coil, blower with motor , Corded/ Cordless Remote Control and 220 volt, 1 phase, 50 Hz, AC supply all and as per specifications. Make: Carrier/Mitsubishi Electric/Toshiba 1.3HP

Supply Installation Testing and Commissioning of following minimum capacity 4-way flow VRV/VRF Cassette Type Indoor ceiling mounted unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet, drain pump grill, necessary supports, vibration isolation, corded/Cordless remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply. Make: Carrier/Toshiba/Mitsubishi Electric 1.0HP

Supply Installation Testing and Commissioning of following minimum capacity High Static Ducted type Indoor unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet,necessary supports, vibration isolation, corded/Cordless remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply. Make: Carrier/Toshiba/Mitsubishi Electric 20.0 HP

Supply Installation Testing and Commissioning of following minimum capacity High Static Ducted type Indoor unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet,necessary supports, vibration isolation, corded/Cordless remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply. Make: Carrier/Toshiba/Mitsubishi Electric 10.0 HP

Supply Installation Testing and Commissioning of following minimum capacity Treated Fresh Air Unit equipped with synthetic washable media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve ,outer cabinet,necessary supports, vibration isolation, corded/Cordless remote control etc suitable for operation on 230 V +- 10% 50 Hz AC supply. Make: Carrier/Toshiba/Mitsubishi Electric : 10.0HP

Air Handling Unit for Operartion Theater Supply & Installation of Floor / Ceiling Suspended type air handling units double skin type complete with suitably insulated panels pressure injected with PUF insulation of suitable density, forward curved blower, with DX coil, filter section with filters (Pre, Fine. HEPA), fan motor, drive set, Mounting base damper etc. as per specifications and drawings including all necessary fittings and accessories complete and suitable for outdoor installation . AHU Shall be supplied with suitable electrical starter panel. 6 row deep cooling coil at 150 ESP. Necessary AHU Kit Shall be supplied along with AHU. Make: Zeco/Edgetech 3500 CFM - 14HP Coil

Supply, fixing and commissioning of refrigerant joint / Branch distibutors between Outdoors with nitrile rubber insulation, supporting etc complete as required. Make: Carrier/Toshiba/Mitsubishi Electric

Supply installation Testing and Commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for F/VRV system, complete with fittings, with suitable adjustable ring type hanger supports, ng/brazing including accessories insulated with XLPE Class O tubular insulation/with Class O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories.Make: Totaline/Met Tube/Rajco 6.5 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

9.5 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

12.7 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

15.86 mm dia (OD) (soft drawn) with appropriate tube thickness with 13mm thick insulation

19 mm dia (OD) (Soft/Hard drawn) with appropriate tube thickness with 13mm/19mm thick insulation

22.2 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

25.40 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

28.58 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

31.8 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

34.9 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

38.1 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

41.3 mm dia (OD) (Hard drawn) with appropriate tube thickness with 19mm thick insulation

Supply Installation Testing & Commissioning of rigid UPVC piping with fittings, supports as per specifications and duly insulated with 6 mm thick closed cell nitrile rubber insulation etc. complete as required. Make: Supreme/Prince/Finolex 50 mm dia ( with 6 mm nitrile rubber Insulation)

32 mm dia ( with 6 mm nitrile rubber Insulation)

25 mm dia ( with 6 mm nitrile rubber Insulation)

Supply Installation Testing and Commissioning of Site fabricated GI ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Make: Tata/Jindal/Sail Thickness 24 Gauge

Supply Installation Testing and Commissioning of Site fabricated GI ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Make: Tata/Jindal/Sail Thickness 22 Gauge

Supply Installation Testing and Commissioning of Site fabricated Aluminium ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Make: Tata/Jindal/Sail Thickness 24 Gauge

Supply Installation Testing and Commissioning of Site fabricated Aluminium ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required. Make: Tata/Jindal/Sail Thickness 22 Gauge

Supply and fixing of following thickness duly laminated aluminium foil finish closed cell Nitrile rubber ( Class O) insulation on duct after applying suitable adhesive for Nitrile rubber . The joints shall be sealed with 50 mm wide and 3mm thick self adhesive nitrile rubber insulation complete as per specifications and as required. (a)13 mm thick insulation with Aluminium foil. Make: Supreme/A Flex/K FLex.

Supply, installation & testing of acoustic lining within supply and return air ducts as per specifications. All ducts shown cross hatched on the approved shop drawings shall be provided with 140-180 kg/m cu. elastomeric nitrile rubber open cell foan acoustic lining as per the specifications. Make: UP Twiga/ Ownes Corning/ A Flex / K Flex 15mm thick acoustic lining.

Supplying & fixing of powder coated extruded aluminum Supply Air Grills/Diffuser with aluminum volume control dampers as per specifications. Make: Tristar/Airflow/Ravistar

Fabrication, supplying and installing of GI tray with cover of following sizes of horizontal and vertical bends, reducers, tees, cross members & other accessories etc. as required and duly supported from the ceiling with dash fastness including painting of suspenders required for accomodating/ laying of refrigerant pipes as complete as required. Make: Mem/Slotco/Legrand a) 150 x 50 x 1.6 mm

Fabrication, supplying and installing of GI tray with cover of following sizes of horizontal and vertical bends, reducers, tees, cross members & other accessories etc. as required and duly supported from the ceiling with dash fastness including painting of suspenders required for accomodating/ laying of refrigerant pipes as complete as required. Make: Mem/Slotco/Legrand (b) 300 x 50 x 1.6 mm

Supply & Installation of Copper Conductor wire , control cum transmission wiring/power cable in suitable PVC conduits between indoor and outdoor unit as complete as required. Make: Polycab/Finolex/KEI/Havells/RR Cable 3 Core x 1.5 Sqmm - Shielded

Refrigerant gas R-410 for top up as complete as required. Make: DuPont/Godrej/Totaline

MS Fabricated (Heavy Duty ) ODU Frame

PART(C)ELEVATOR WORKS GMC & TEACHING HOSPITAL: Type and CapacityMRL Gearless Passenger Elevator, Approximately 680 Kg., 10 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 12.72 meters or more [Ground Floor + 3 Floor],Serving4 Stops 4 Openings 4 Levels [All on the same side],Shaft Dimensions Available1850 MM [wide] x 2350 MM [deep],Car Size1100 mm (W) x 2000 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMC,Make Otis / Mitsubishi/Easa/ Thyssen Krupp.FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1510mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 884 Kg., 13 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 12.72 meters or more [Ground Floor + 3 Floor],Serving4 Stops 4 Openings 4 Levels [All on the same side],Shaft Dimensions Available1800 MM [wide] x 1950 MM [deep],Car Size1100 mm (W) x 1600 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panel,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMC,Make Otis / Mitsubishi/Easa/ Thyssen Krupp.FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1600 mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 1360 Kg., 20 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 7.2 meters or more [Ground Floor + 1 Floor],Serving2 Stops 2 Openings 2Levels [All on the same side],Shaft Dimensions Available3000 MM [wide] x 2200 MM [deep],Car Size2000mm (W) x 1550 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMCMake Otis / Mitsubishi/Easa/ Thyssen Krupp.,FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1510mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 544 Kg., 8 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 16.0 meters or more [Ground Floor + 4 Floor],Serving5 Stops 5 Openings 5Levels [All on the same side],Shaft Dimensions Available1850 MM [wide] x 1650 MM [deep],Car Size1100mm (W) x 1300 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2200 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMC,Make Otis / Mitsubishi/Easa/ Thyssen Krupp.FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1510mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 544 Kg., 8 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 9.6 meters or more [Ground Floor +2 Floor],Serving3 Stops 3 Openings 3Levels [All on the same side],Shaft Dimensions Available1850 MM [wide] x 1650 MM [deep],Car Size1100mm (W) x 1300 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMCMake Otis / Mitsubishi/Easa/ Thyssen Krupp.,FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1510mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 844 Kg., 13 Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 16.80 meters or more [Ground Floor +4 Floor],Serving5Stops 5Openings 5Levels [All on the same side],Shaft Dimensions Available1850 MM [wide] x 2350 MM [deep],Car Size1100mm (W) x 1300 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening800 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMCMake Otis / Mitsubishi/Easa/ Thyssen Krupp.,FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1510mm and over head of 4500 mm of the Building

Type and CapacityMRL Gearless Passenger Elevator, Approximately 1632 Kg., 24Persons,Speed1.0 MPS,Type of DriveA.C. Variable Voltage Variable Frequency with Microprocessor,Location of Machine-roomMachine Room Less,TravelApproximately 16.80 meters or more [Ground Floor +4 Floor],Serving5Stops 5Openings 5Levels [All on the same side],Shaft Dimensions Available3000.0 MM [wide] x 2350 MM [deep],Car Size2000mm (W) x 1800 mm (D) x 2200 mm (H),Car EnclosureConstructed out of Stainless Steel Hairline Finish Car Panels,Car EntranceCenter Opening Automatic Framed Stainless SteelHoney combFinish,Hoistway EntranceCenter Opening Automatic Framed Stainless Steel Honey comb Finish,Clear Opening1000 MM [Wide] x 2000 MM [High],Door OperationCenter Opening Automatic doors.ControlSimplex Full collective operation With / Without Attendant,Power Supply415 Volts, 3 Phase, 50 Hertz Alternating Current,FanVentilation Fan,Warranty/Maintenance1 Year warranty & 5 Years AMC.Make Otis / Mitsubishi/Easa/ Thyssen Krupp.,FlooringGranite Flooring by Customer. 20 mm Recess will be provided by supplier,LightingDiffused LED Lighting in car/Eq.,IndicatorsDigital Direction and Position Indicators in both car and at all landings,Other FeaturesBattery Operated Emergency Light with Rechargeable Battery,L.E.D. based Braille Buttons with dot matrix screen Hands Free Press and Speak IntercomSystem Capable of withstanding +10% to –10% Variation in Supply Voltage FluctuationsFull Height Infrared Safety Curtain with Minimum 150 Intersecting BeamsStainless Steel False Ceiling in Plain FinishPit LadderAutomatic Rescue Device to automatically bring the elevator to a landing in case of power failure and Controller FailurLoad Weighing Device with Overload By - pass Feature.All Signal Fixtures will be in Stainless Steel Face PlatesShaft Lights.Available Pit size 1700mm and over head of 4500 mm of the Building

Part(D)FIRE FIGHTING WORKS GMC & TEACHING HOSPITAL: a)SUB HEAD-A (PIPING & VALVES) Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.150 mm. Dia

100 mm. Dia

80 mm. Dia

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges ,tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required 32mm dia

32 mm dia.

40 mm dia.

50 mm dia.

65 mm dia.

80 mm dia.

100mm dia

150mm dia

200 mm dia (wall thickness 6.3 mm)

250 mm dia (wall thickness 6.3 mm)

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required : 200mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required 150 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS:5312 complete with rubber gasket, GI bolts, nuts,washers etc.as required 100 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm dia.

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 50 mm dia.

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :150 mm dia.

100 mm dia.

80 mm dia.

Providing and fixing dial type pressure gauge with isolation cock and copper pipe at hydrant station.Dial diameter 100 mm calibration 0-15 kg/ sq.cm.

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange. 100mm dia

150mm dia

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

SUB HEAD-B (FIRE HYDRANT ACCESSORIES): Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Gunmetal

Supplying and fixing Single headed external yard hydrant valve with 1 No. 63 mm dia instantaneous FM Gunmetal/Stainless Steel coupling and cast iron wheel, ISI marked, conforming to IS 5290 (type A) with blank Gunmetal/Stainless Steel cap and chain as required :Single headed Gunmetal

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. 30m

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :Gun Metal

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for instantaneous connection to interconnect hose pipe coupling as required :Gun Metal

Supplying and fixing orifice plate made out of 6 mm thick stainless steel (Grade 304) with orifice of required size to be fitted between flange & landing valve of external and internal hydrants to reduce pressure at the outlet to the level of 3.5 kg/cm2 complete as required.

Supplying and fixing of fire brigade connection of cast iron body with gun metal male instantaneous inlet couplings complete with cap and chain as reqd. for suitable dia MS pipe connection conforming to IS 904 as required :2 way-100 mm dia M.S. Pipe

4 way - 150 mm dia M.S. Pipe

Supplying and fixing air vessel made of 250 mm dia, 8 mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

SUB HEAD-C (SPRINKLERS ACCESSORIES) Providing, fixing, testing & commissioning of 15mm dia quartzoid bulb type sprinklers of rating 68 degree centigrade with required accessories :Normal response Pendent type

Horizontal side wall sprinkler

Providing & fixing flow switch in following sizes M.S. pipe including connection etc as required.150 mm dia.

Providing, fixing, testing & commissioning of installation control valve of cast iron body, brass/bronze working parts comprising of water motor alarm, bronze seat clapper, clapper arm and hydraulically driven mechanical gong bell to sound continuous alarm when the wet riser/sprinkler system activates, pressure gauges, emergency releases, strainer, pressure switch, cock valve complete with drain valve and bypass, test control box, ball valves, MS pipe of required size, flanges, orifice plate, gasket etc of follwing sizes as required :150 mm dia.

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets,center bracket, stockbar of following sizes complete as 700mm

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets,center bracket, stockbar of following sizes complete as 1000mm

Providing, installation, testing & commissioning of adjustable rosette plate for 15mm dia in white finish UL Listed or FM approved complete as required.

Suitable cement concrete foundation duly plastered with anti vibration pads.2280 lpm at 70 m Head

Suitable cement concrete foundation duly plastered and with anti vibration pads.2280 lpm at 70 m Head

Suitable cement concrete foundation duly plastered and with anti vibration pads.180 lpm at 70 m Head

Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air release valve on top and flanged connection to riser, drain arrangement with 25 mm dia gun metal wheel valve with required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required.

(d) Suitable cement concrete foundation duly plastered and with anti vibration pads.450 lpm at 35 m Head

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Circular tank

N S-items: Providing and fixing gunmetal single acting air release valve with screwed inlet 25 mm dia..

Providing and fixing blank flanges as per table 'E' with asbestos gasket, nut, bolts, washers complete 150 mm dia.

SUB HEAD-B (FIRE HYDRANT ACCESSORIES): Providing and fixing door with frame for all internal fire hydrants fabricated from 20x20x3 mm and 40x20x3 mm aluminium hollow box sections mounted with 3 no. of 100 mm Aluminium butt hinge on Aluminium angle frame of 45x45x5 mm size with hold fasts fixed to wall with P.C.C. (1:2:4) blocks 200x200x100 mm including 2 nos allen key lock for locking along with padlock arrangement & fully glazed with 4 mm thick float glass approved by local Fire Authority, powder coated fire red finish with " fire hose' written on front suitable to house 15 mm long two length of canvas hose with couplings, one no of branch pipe, one fire mans axe and two numbers of portable extinguishers, first aid fire hose and supports for hoses, branch pipes, Axe and hose reel. Size 1200x 600 mm complete as per approved design including necessary fixing arrangement for hoses & axe and branch pipe.)

Providing and fixing fire hose cabinet fabricated from 16 gauge M.S. Sheet with single or double glazed front door and locking arrangement, painted "Fire Red" with powder coated paint "Fire Hose" written on front including suitable supports to place 900 mm above ground level, approximately size 750x600x250 mm deep (to house two lengths of canvas hose with couplings, branch pipe and nozzle for external hydrants)

Supplying and fixing of Fire Man's Axe with heavy insulated rubber tested upto 20 KV and confirming to IS :926.

SUB HEAD-C (SPRINKLERS ACCESSORIES) Providing & fixing 25 mm dia. UL listed gunmetal inspector test and drain valve with integral sight glass connected to drain line complete in all respects.

SUB HEAD-D (FIRE EXTINGUISHERS & MISC. ITEMS) Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, suspension bracket, confirming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. Capacity 4.5 kg. ISI Marked.( Contractor should submit test certificate form manufacturer along with serial number of every extinguishers supplied.)

Providing and fixing ABC powder type fire extinguishers consisting of welded M.S. cylindrical body automatic modular ABC powder type extinguisher actuated through a sprinkler head mounted on The extinguisher body finished externally with red enamel paint and fixed to ceiling with brackets complete with internal charge.Capacity 4 Kg.(IS:15683)

Providing and fixing mechanical foam type (ISI marked) fire extinguishers consisting of welded M.S. cylindrical body squeeze lever discharge valve 30 cm long high pressure discharge hose, discharge nozzle suspension bracket ISI marked finished externally with red enamel paint and fixed to wall with brackets complete with internal charger.9 liters capacity. (IS. 15683)

Providing and fixing water Co2(ISI marked) extinguishers including all accessories as per IS specification with wall bracket with rawl plug Capacity 9 liters.(IS:15683)

Providing and fixing of self illuminated / auto glow "EXIT" signs printed on photoluminescent sheet containing self illuminated base chemical, of appropriate size not less than 400 x 150 mm, suspended from ceiling or fixed to the walls with accessories as required and as directed at site.

Providing and fixing Carbon-di-oxide fire extinguishers consisting of welded M.S cylindrical body, squeeze lever discharge valve fitted with internal discharge tube, 30cms long high pressure discharge hose, discharge nozzle, trolly mounted, confirming to IS : 15683 finished externally with red enamel paint and fixed to wall with brackets with rawl plug/dash fasteners complete with internal charge. Capacity 22.5 kg. ISI Marked.( Contractor should submit test certificate form manufacturer along with serial number of every extinguishers supplied.)

Providing and fixing mechanical foam type (ISI marked) fire extinguishers consisting of welded M.S. cylindrical body squeeze lever discharge valve 30 cm long high pressure discharge hose, discharge nozzle, trolly mounted ISI marked finished externally with red enamel paint and fixed to wall with brackets complete with internal charger.50 liters capacity. (IS. 15683)

SUB HEAD-E (FIRE PUMPS & ACCESSORIES) Providing and fixing liquid level controller for fire pump to stop fire pump in case of low level of water in tank , cost of conduit, cable and panel including making connection to pump panel and commissioning complete.

Float type Sensor with panel and installation

Providing and fixing M.S. epoxy coated puddle flanges fabricated with MS pipe Heavy class (minimum 550mm long, IS:1239) and MS sheet 6 mm thick projected 150 mm all-round the pipe for tanks as per standard details.150mm dia-MS Flanged (BS -10 Table E) end on air side and plain on water side

100mm dia-MS Flanged (BS -10 Table E) end on air side and plain on water side

80mm dia-MS Flanged (BS -10 Table E) end on air side and plain on water side

50mm dia -Plain on water side and threaded on air side

PART(E)INTERNAL PLUMBING SANITARY INSTALLATION WORKS GMC & TEACHING HOSPITAL: Providing and fixing white vitreous china extended wall mounting water closet of size 655x365x755 mm of approved shape including providing & fixing white vitreous china cistern with dual flush fitting, of flushing capacity 3 litre/ 6 litre (adjustable to 4 litre/ 8 litres), including duroplast seat cover, and cistern fittings, nuts, bolts and gasket etc complete. cat. No S1031103 Make:- Cera, Grohe, Kholer, Kerrovit

Providing and fixing wash basin size 630 x 450 x 225mm with C.I. brackets, 15 mm dia CP Brass single hole basin mixer of approved quality cat No F1019451 and make, including painting of fittings and brackets, cutting and making good the walls wherever required. Make cat S 2040104 Cera, Jaquar, Grohe ,Kerrovit (a) White Vitreous China Wash basin size 630x450 mm with a 15 mm CP Brass single hole basin mixer

Providing and fixing white vitreous china battery based infrared sensor operated urinal of approx. size 320 x 300 x 525 mm having pre & post flushing with water (0.75 ltr consumption), having water inlet from back side, including fixing to wall with suitable brackets all as per manufacturers specification Cat no S4010102 Make : Cera,Duravit, JaquarKerrovit

Providing and fixing Stainless Steel A ISi 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 250 mm Crea, Hafle ,Jayna

Providing and fixing white vitreous china laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required :Size 450x300x150 mm Make Cera, jaquar, kholer,Kerrovit

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards, Make: Jaquar, Cera, Kholer Cat. No. F1019151,Kerrovit15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:893115 mm nominal bore make, Cera, Jaquar Kholer ,Kerrovit

Providing and fixing 750x900 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour.15 mm nominal bore with 45 cm length

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineerin- charge.Cera, Jaquar, KerrovitKholer

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing CP Brass Single lever telephonic wall mixer of quality & make as Specified. Make Cera, Jaquar,Kerrovit and Kholer Cat. No. F1015414a) 15 mm nominal dia

Providing and fixing C.P. Hand shower with 15 or 20 mm inlet :Make Cera, Jaquar, Kholer150 mm diameter

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms, Make:- Cera, ,KerrovitJaquar, Kholer

Providing and fixing Cp brass soap Dish Holder having length of 138mm, breadth 102mm, height of 75mm with concealed fitting arrangements, Make: Cera Jaquar,Kerrovit and Kholer

Providing and fixing toilet paper holder :C.P. brass Make Cera, Jaquar And Kholer

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete.32 mm dia

Providing and fixing Cp liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. Make: Cera, Jaquar and Kholer

SOIL, WASTE & VENT PIPES: Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905: 75 mm diametre :

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905: 75 mm dia

Hubless centrifugally cast (spun) iron pipes epoxy coated inside & outside IS:15905

SS 304 grade coupling with EPDM rubber gasket 75 mm dia

SS 304 grade coupling with EPDM rubber gasket

Hubless centrifugally cast (spun) iron epoxy coated inside & outside as per IS:15905

RAIN WATER PIPES: Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.75 mm diametre

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diametre

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion. 75mm

Single tee with door75x75x75 mm

Single tee with door110x110x110 mm

Bend 87.5°75 mm bend

Bend 87.5° 110 mm bend

Shoe (Plain) 75mm Shoe

Shoe (Plain) 110mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75 mm

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diametre and weighing not less than 440 grams.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATER SUPPLY INTERNAL: Providing and fixing Polyethelene-Aluminium-Polyethelene PE-ALPE Composite Pressure Pipes conforming to IGC-308, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge.INTERNAL WORK - EXPOSED ON WALL: 1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

3240 (40 mm OD) pipe

4050 (50 mm OD) pipe

Providing and fixing Polyethelene-Aluminium- Polyethelene PE-ALPE Composite Pressure Pipes conforming to IGC-308, U.V. stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers,couplers & connectors etc., with clamps at 1.00 metre spacing.This includes the costs of cutting chases and including testing of joints complete as per direction of the engineer in charge.Concealed work, including cutting chases and making good the wall etc. 1620 (20 mm OD) pipe

2025 (25 mm OD) pipe

2532 (32 mm OD) pipe

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :20 mm dia nominal bore

25 mm dia nominal bore

32 mm dia nominal bore

40 mm dia nominal bore

50 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25 mm nominal bore

Providing and fixing brass ferrule with C.I. mouth cover including boring and tapping the main :25 mm nominal bore

Providing, laying, testing & commissioning of 'B' class heavy duty G.I. pipe conforming to IS 1239 including welding, fittings like elbows, tees, flanges, tapers, nuts, bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :25 mm

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :65 mm dia

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required 80 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank 7 layer , IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.Circular tank

PART(E) EXTERNAL PLUMBING SANITARY INSTALLATION WORKS GMC & TEACHING HOSPITAL: Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design : 150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

NON-SCHEDULE ITEMS-F: Providing and fixing wall mounted recess hand dryer complete including fixing on wall with PVC rawl plug and CP brass screw complete. (Make: Euronics/ Cera/dolphin)

Providing and fixing of 1 No. Wall Mounted Grip in polished & Grab Bar at fixed height for handicap toilet complete as required. (Make-Kohler / Cera/dolphin) & Equivalent Make

Providing and making arrangement for shut-off the water supply line in to the tank comprising of 50mm dia motorised valve, liquid level controller to control cut-in and cut-out of motorised valve when the water is low and high in Overhead water tank complete with necessary electrical works, probs etc.

Providing and making arrangement for shut-off the water supply line in to the tank comprising of 40mm dia motorised valve, liquid level controller to control cut-in and cut-out of motorised valve when the water is low and high in Overhead water tank complete with necessary electrical works, probs etc.

Providing and fixing Electrical storage water heaters of adequate capacity fixing on wall with dash fastener compelete as per manufacturers spacifications.horizontal/vertical outlets fixed to floor with all accessories.Make : Anchor, Hindware, AO Smith 15 Liters water mounted heater

Providing and fixing Electrical storage water heaters of adequate capacity fixing on wall with dash fastener compelete as per manufacturers spacifications.horizontal/vertical outlets fixed to floor with all accessories.Make : Anchor, Hindware, AO Smith 50 Liters water mounted heater

EXTERNAL SEWERAGE WORK: Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : All KInds of Soil Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Extra for excavating trenches for pipes, cables, etc. in ordinary/hard rock exceeding 1.5 m in depth but not exceeding 3 m. (Rate is over corresponding basic item for depth upto 1.5 metre). Ordinary roack Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.ALl Kins of soil

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.Ordinary rock

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. All kinds of soil

Extra for every additional lift of 1.5 m or part thereof in excavation /banking excavated or stacked materials. Ordinary rock

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

Carriage of earth by mechanical transport including loading, unloading and stacking upto 1km

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 250 mm diameter

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete : 300 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 250 mm diameter

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 300 mm diameter

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes :Size 90x80 cmith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :0.91 m deep with SFRC cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 m With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :1.68 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.52 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :2.30 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means over areas (exceeding 30cm in depth. 1.5 m in width as well as 10 sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.All Kind of Soil

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.Carriage of earth by mechanical transport including loading, unloading and stacking upto 1km

Carriage of earth by mechanical transport including loading, unloading and stacking upto 1km

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :150 mm dia. R.C.C. pipe

250 mm dia. R.C.C. pipe

300 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of R.C.C. pipes including bed concrete as per standard design : 150 mm dia. R.C.C. pipe

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of R.C.C. pipes including bed concrete as per standard design : 250 mm dia. R.C.C. pipe

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mmx25mm and over all minimum length 263 mm and width as 165mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design :Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes :Size 90x80 cmith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :0.91 m deep with SFRC cover and frame (heavy duty, HD- 20 grade designation) 560 mm internal diameter conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg., fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 0.91m internal dia (at bottom) beyond 0.91 m to 1.67 mWith common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56 m dia at top in cement mortar 1:4 (1 cement :4 coarse sand) inside cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement foundation concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size) and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement, all complete as per standard design :1.68 m deep with SFRC Cover and frame (heavy duty HD 20 grade designation) 560 mm internal diameter conform ing to I.S. 12592, total weight of cover and frame to be not less than 182 kg. fixed in cement concrete 1:2:4 (1 ce ment : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering, shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately) :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra depth for circular type manhole 1.22 m internal dia (at bottom) beyond 1.68 m to 2.29 m :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry road gully chamber 50x45x60 cm with bricks in cement mortar 1:4 (1 cement : 4 coarse sand) including 500x450 mm pre-cast R.C.C. horizontal grating with frame complete as per standard design :With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Exacavating trenches of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms , depth upto 1.5 m including getting out the exacavated soil, and then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed within a lead of 50mtr. All Kins of soilPipes, cables etc., exceeding 80 mm dia, but not exceeding 300 mm dia

Providing,Laying and fixing Polyethelene-Aluminium-Polyethelene PE-ALPE Composite Pressure Pipes conforming to IGC-308, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. (For Domestic Water Supply in underground and over ground )25mm dia nominal bore OD

32mm dia nominal bore OD

100mm dia nominal bore OD

Providing,Laying and fixing Polyethelene-Aluminium-Polyethelene PE-ALPE Composite Pressure Pipes conforming to IGC-308, U.V.stabilized with carbon black having thermal stability for hot & cold water supply, capable to withstand temperature up to 80°C, including all special fittings of composite material (engineering plastic blend and brass inserts wherever required) e.g. elbows, tees, reducers, couplers & connectors etc., with clamps at 1.00 metre spacing. This includes testing of joints complete as per direction of the Engineer-in-charge. (For Flushing Water Supply inunderground and over ground) 25 mm OD

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :80 mm dia

150 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :25 mm nominal bore

32 mm nominal bore

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Domestic Water Pumps (Set of Two Pumps One Working + One Standby) Capacity : app. 100 lpm Head : app. 65 m

Filter Water Transfer Pumps (Set of Two Pumps One Working + One Standby) Capacity : app. 100lpm Head : app. 30 m

Flushing Water Pumps(Set of Two Pumps One Working + One Standby) Capacity: app. 100 lpm: Head : app. 65 m

Pressure Filter (Domestic Water) : Providing and fixing vertical pressure filter with dual media filter (comprising of 600mm bed depth of graded sand gravel and 600mm bed depth of Anthracite) fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2) Discharge 9000 lph, Filtration Rate : 20000 lit./m2/h , Suggested dia app.: 1500 mm

Activated carbon Filter (Domestic Water): Providing and fixing vertical activated carbon filter comprising of activated carbon filter media fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2) Discharge : 9000 lph, Filtration Rate : 20000 lit./m2/h , Suggested dia app.: 1500 mm

Water Softener: Providing and fixing ‘Cation’ ION exchange water softener fabricated from minimum 8mm thick M.S. plate on shell and 10mm thick M.S. plate on dished ends complete with initial charge of filter media and ION exchange resins, face piping accessories, piping testing and commissioning complete with resins of approved quality and make and brine tank of required capacity. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration).Minimum expected rate of flow: 9000 lph , Minimum expected rate of flow: 9000 lph , Total soft water to be produced between two regeneration: app. 100 Cum, Expected raw water hardness : app. 500 ppm, Expected treated water hardness: less than 100 ppm

Providing and fixing M.S salt saturator, internally rubber lined as per requirement and externally painted with suitable anti-corrosive paint, with all required accessories for holding and supplying salt for softener complete in all respects, with electrically operated stirrer and of capacity 150 litres.

Providing and fixing motor pump controller cum water level indicating panel in powder coated sheet metal box in 16 gauges M.S including the following:Electronic water level controller working on magnetic type sensing probes with necessary length of armored cable up to control panel.Electronic minimum 4-level indicator with magnetic type sensing probes and necessary length of armored cable upto control panel.Arrangement of alternate switching mechanism for operational and standby pumps.Underground tanks Minimum 4 level Multi level indicators with magnetic type sensor probes complete. (Each UGT)

Providing and fixing G.I. pipes (I.S. 1239 heavy duty class) complete with all necessary G.I. Fittings including all necessary fittings like bends, elbows, tees etc., either welded or screwed or flanged joints as per requirements, including all anchor blocks, anchor fasteners, couplings in all respects including enamel painting of required shade, cutting holes and chases in RCC wall and making good complete (The cost of flanges will be paid separately). 100mm dia

Providing and fixing G.I. pipes (I.S. 1239 heavy duty class) complete with all necessary G.I. Fittings including all necessary fittings like bends, elbows, tees etc., either welded or screwed or flanged joints as per requirements, including all anchor blocks, anchor fasteners, couplings in all respects including enamel painting of required shade, cutting holes and chases in RCC wall and making good complete (The cost of flanges will be paid separately). 150mm dia

Providing and fixing C I body flanged strainer fabricated out of 1.6 mm thick Stainless Steel 304 sheet having 0.6 mm to 0.8 mm dia perforations complete. 100mm dia

Providing and fixing C I body flanged strainer fabricated out of 1.6 mm thick Stainless Steel 304 sheet having 0.6 mm to 0.8 mm dia perforations complete. 150mm dia

Providing and fixing butterfly valves, wafer end type class PN 1.0 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box) 100mm dia nominal bore.

Providing and fixing butterfly valves, wafer end type class PN 1.0 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box) 150mm dia nominal bore.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Providing and fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size, drilling, welding fixing and welding to insert plates in RCC structural members or through dash fasteners as per site conditions as directed by Engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.)

Submersible pumps Providing, fixing and testing of Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, MCB, copper bus bar, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect(one working+One Standby)(Solid handiling capacity 12mm)Capacity - 225 lpm (Each)Head - 12 m, HP (Approx) - 1.0 HP

PART(F) WATER SUPPLY PUMPS & EQUIPMENTS WORKS GMC & TEACHING HOSPITAL: WATER SUPPLY PUMPS & EQUIPMENTS Domestic/Flushing Water Pump (Hydropneumatic System With Variable Speed Pumps) Providing, fixing and testing of skid mounted variables frequency drive hydropneumatic system with variable speed system comprising of :-Vertical, inline multistage centrifugal pumping set with stainless steel SS-304 stage casing and SS-304 impellers with stainless steel SS-316L shaft as per IEC standards and GJL250 cast i.ron suction & discharge casing, connected to TEFC ventilated induction motor of 2 pole, 2900rpm, suitable for 400/440 Volts, 3 phase, 50 Hz A.C. supply.Pressure vessel of non corrosive FRP composite construction lined with NSF and/or FDA listed material, like high density polyethylene with fully replaceable polyurethane. Air cell burst pressure of minimum of 5 times the vessel operating pressure and cycle tested for 2,50,000 cycles. No. and capacity of Pressure Vessel – 01 Nos. x 200 LtrsControl Panel with programmable logic controller (PLC) for cyclic operation of pumps. Pump working sequence should change after every operation.Contractor overload relays and MCBs should confirm to IEC 898 – 1995/ specifications. Blinking indications for pumps start, trip, low level trip, health supply should be provided in the panel along with the ammeter & voltmeter. Control panel should also consist of cooling fan. Main incomer MCB, Outgoing MCBs, Single phase preventors complete with auto manual swiches, dry run protection arrangements,Voltmeter/Ameter, Indication lights, Controller for dry run protection.Pressure transmitting relay bellow type fitted with micro switch and having maximum pressure and differential scale should confirming BS-6134 standards and IP55 protection class.GI heavy class(IS:1239) Suction and delivery header with brass Ball valves with plastic coated handle(tested to 20kg/sqcm), Hot Pressed brass OT-58 with stainless steel ball and P.T.F.E seal and O-Ring. Brass NRVs (Test pressure =20 Kg/sqcm) to be used should be with Springs and O-Ring arrangement.Complete set system to be mounted on a common base frame and shall follow following duty(Skid shall be powder coated ).Domestic Water Pumps (Set of Three Pumps Two Working + One Standby) Capacity : app. 150 lpm Head : app. 65 m

Filter Water Transfer Pumps (Set of Three Pumps Two Working + One Standby) Capacity : app. 150 lpm Head : app. 30 m

Flushing Water Pumps(Set of Two Pumps One Working + One Standby) Capacity : app. 150 lpm Head : app. 65 m

Pressure Filter (Domestic Water) Providing and fixing vertical pressure filter with dual media filter (comprising of 600mm bed depth of graded sand gravel and 600mm bed depth of Anthracite) fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2 Discharge : 12500 lph Filtration Rate: 20000 lit./m2/h Suggested dia app.: 1500 mm

Activated carbon Filter (Domestic Water) Providing and fixing vertical activated carbon filter comprising of activated carbon filter media fabricated from high performance M.S plate of minimum 8mm thick for shell & 10mm thick for dished ends with top and bottom flanged openings including top and bottom hub and lateral distribution and collection system complete with initial charge of filter media, face piping, valves, accessories, painting, testing and commissioning complete.(Tested to 6 Kg/m2) Discharge : 12500 lph Filtration Rate : 20000 lit./m2/h Suggested dia app. : 1500 mm

Water Softener Providing and fixing ‘Cation’ ION exchange water softener fabricated from minimum 8mm thick M.S. plate on shell and 10mm thick M.S. plate on dished ends complete with initial charge of filter media and ION exchange resins, face piping accessories, piping testing and commissioning complete with resins of approved quality and make and brine tank of required capacity. (Bidder must indicate type and quantity of resin used and quantity of salt required per regeneration). Minimum expected rate of flow: 12500 lph Total soft water to be produced between two regeneration: app. 100 Cu.m Expected raw water hardness : app. 500 ppm Expected treated water hardness: less than 100 ppm Max. working pressure : 4 Kg/cm2 Total soft water to be produced between two regeneration: app. 10 Cu.m

Providing and fixing M.S salt saturator, internally rubber lined as per requirement and externally painted with suitable anti-corrosive paint, with all required accessories for holding and supplying salt for softener complete in all respects, with electrically operated stirrer and of capacity 150 litres.

Providing and fixing motor pump controller cum water level indicating panel in powder coated sheet metal box in 16 gauges M.S including the following:Electronic water level controller working on magnetic type sensing probes with necessary length of armored cable up to control panel. Electronic minimum 4-level indicator with magnetic type sensing probes and necessary length of armored cable upto control panel.Arrangement of alternate switching mechanism for operational and standby pumps.For Water level indicators with following details:Underground tanks Minimum 4 level Multi level indicators with magnetic type sensor probes complete. (Each UGT)

Providing and fixing G.I. pipes (I.S. 1239 heavy duty class) complete with all necessary G.I. Fittings including all necessary fittings like bends, elbows, tees etc., either welded or screwed or flanged joints as per requirements, including all anchor blocks, anchor fasteners, couplings in all respects including enamel painting of required shade, cutting holes and chases in RCC wall and making good complete (The cost of flanges will be paid separately). 100mm dia

Providing and fixing G.I. pipes (I.S. 1239 heavy duty class) complete with all necessary G.I. Fittings including all necessary fittings like bends, elbows, tees etc., either welded or screwed or flanged joints as per requirements, including all anchor blocks, anchor fasteners, couplings in all respects including enamel painting of required shade, cutting holes and chases in RCC wall and making good complete (The cost of flanges will be paid separately). 150mm dia

Providing and fixing C I body flanged strainer fabricated out of 1.6 mm thick Stainless Steel 304 sheet having 0.6 mm to 0.8 mm dia perforations complete. 100mm dia

Providing and fixing C I body flanged strainer fabricated out of 1.6 mm thick Stainless Steel 304 sheet having 0.6 mm to 0.8 mm dia perforations complete. 150mm dia

Providing and fixing butterfly valves, wafer end type class PN 1.0 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box) 100mm dia nominal bore.

Providing and fixing butterfly valves, wafer end type class PN 1.0 as per I.S:13095 - 1991 or BS:5155, including necessary nuts, bolts, gaskets etc. complete (without gear box) 150mm dia nominal bore.

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays Cross Member with perforation not more than 17.5%, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required. 300 mm width X 50 mm depth X 1.6 mm thickness

Providing and fixing M.S. structural work fabricated from standard section e.g. M.S rounds, angles, channels, plates including cutting to size, drilling, welding fixing and welding to insert plates in RCC structural members or through dash fasteners as per site conditions as directed by Engineer-in-charge including cutting and making good the walls, ceilings and floors (for pipe supports, clamps etc.)

Submersible pumps Providing, fixing and testing of Submersible single stage single entry pumps with C.I.body and C.I. two vane enclosed type impeller connected to TEFC submersible motor for 415 volts, 3 phase, 50 cycles including MCC panel with level controllers, auto control, sequential change over facility with one proper working at low level & two proper working at high level with an audible alarm including all interconnectivity cables, MCB, copper bus bar, with both pumps connected to common outlet header including valves, non return valves, lifting chains etc. complete in all respect (one working+One Standby) (Solid handiling capacity 12mm) Capacity - 225 lpm (Each) Head - 12 m HP (Approx) - 1.0 HP

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer –in-charge, upto 90 metre depth below ground level.all types of soil 300 mm dia.

Rocky strata including Boulders 300 mm dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer –in-charge.200 mm nominal size dia.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 200 mm nominal size dia.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarse sand of size range 1.5 mm to 2 mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer –in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).200 mm dia

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910, on 12 mm dia steel bar conforming to IS: 1786, having minimum cross section as 23 mmx25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture’s permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

SEWAGE TREATMENT PLANT (MOVING BED BIO REACTOR TECHNOLOGY) Design, supplying, installing, testing & commissioning of Sewage Treatment Plant (excluding excavation, back filling & disposal of surplus earth MS/Civil construction work) for the following duty:Nature of effluent - Domestic Sewage from toilet, kitchen waste water shall be discharged into the STP. Design to take consideration of same.Daily average flow - 150 Cum / Day pH - 7.5 – 8.5 BOD5 - 250 – 400 Mg/L S. Solids - 200 – 450 Mg/L COD - 400 – 600 Mg/L T Nitrogen- Less than 35 Mg/L Phosphorus -Less than 10Mg/L Oil & Grease - 50 Mg / L Effluent discharge standard after treatment pH - 6.5 – 8.5 BOD5 - Less than 10Mg/L S. Solids - Less than 10 Mg/L COD - Less than 60 Mg/L T Nitrogen- Less than 10 Mg/L Phosphorus -Less than 2 Mg/L Oil & Grease - Less than 10 Mg / L Sewage treatment plant shall include the following items: Screen Chamber - 1 no. Oil and Grease Trap - 1 no. Sewage equalization tank / sump - 1 no. Anoxic Tank-1 No. MBBR Tank - 2 nos. (equal capacity each) Tube Settler - 1 no. (with lamina clarifier) CC Tank - 1 no. Sludge Holding Tank - 1 no. UF Feed water Tank - 1 no. Filtration through MGF & ACF Treated Water Tank UF Unit Air Blowers, Pumps & equipment Piping, valves etc Electrical Panel & Cabling Note: Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity.Supply, installation, testing & commissioning of 2 Nos Stainless Steel Perforated, Corrugated Bar Screen with suitable lifting arrangement (size 600 mm wide x 600 mm high approx)

Make : KWT/3SW/Ecologix: Supply, installation, testing & commissioning of level switch for automatic operation of the system complete with auxillary NO/NC contacts for each tank.

Make : Minilec/ Pune Techtral Supply, installation, testing & commissioning of non clogging type submersible pumps complete with all accessories, CED Coating, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Provison shall be kept to run both pumps simultaneously in case of emergency. Pumps shall have following duty: Make: EBARA/GRUNDFOS Submersible Sewage Pumps for transfer of Raw Sewage in EQT (1 working & 1 standby) :- Flow rate (each) = 30 m3/hr each Head = 8-12 Mtr MOC : CI (Solid handling size for this pump shall be 20-30 mm).

Sludge recirculation pump (2 Nos - 1 working + 1 Standby) Flow rate (each) = 20 m3/hr Head = 8-12 Mtr MOC : CI (Solid handling size for this pump shall be 7 mm).

Plant room sump pump (2 Nos - 1 working + 1 Standby) Flow rate (each) = 30 m3/hr each Head = 8-12 Mtr (Solid handling size for this pump shall be 15 mm). Provision of guide ropes to guide submersible pump from upper level to operational level in sump basin with channels / angle section of MSEP shall be made by the STP contractor.

Air diffusion system shall include the following: 2 Nos. twin type rotary air blowers (1W + 1S) capable of delivering 550 cum/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles AC supply.

Make : BETA/EVERAST/KEY Air piping shall comprise of pipes droppers / laterals with MSEP (''C'' Class) Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good. Contactor to submit detailed P & I indicating their proposal

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. (Imported fine bubble membrane diffusers)

Make :Rehau / Walkton/EDI Bronze Ball valve and air dispersion grid as required for STP as described above. Note : Air dispersion system shall be provided for Sewage Sump, aeration tank and Sludge Holding Tank

Providing and fixing all piping (as described below) and isolation control valves for making the system complete. SS 304 : Submerged air piping MS Epoxy : Air piping & pumped effluent riser (non-submerged) MSEP piping : Pumped effluent (submerged) & tank overflow pipe line MSEP : Interconnecting pipe line after delivery header of pump/ filter

Supply, installation, testing and commissioning of package type Ultra Filtration system of suitable capacity for Flushing water of 150 KLD capacity complete with pre-treatment system comprising of UF hollow fibre membranes, high pressure pumps (1W+1S)), chemical dosings, backwash pumps (1W+1S), piping, valves, pressure gauges, etc complete. The unit shall have all interlocking for safe operation of plant. The unit shall have skid mounted electrical panel complete with required starters and shall also have all Annuanciation and Controls. Indication instrumentation shall also be provided. PLC with input/output modules shall be integrated with all auto equipments/ valves in auto mode. System Integrator Make: KWT/3SW/Ecologix

Supply, installation, testing and commissioning of MBBR media of suitable capacity as per manufacturer recommendation to be installed in MBBR reactor Tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps.

Make : Cooldeck/MM Aqua/Perfectus: Supply, installation, testing and commissioning of PVC tube deck settling media to be installed in Secondary Tube Setller tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps .

Make : Alfa/Sukruit/Perfectus Supply of Anoxic mixer

Make: Aqua Itly/3SW/ATE Make: Aqua Itly/3SW/ATE. Supplying, installing, testing & commissioning of horizontal centrifugal water pumps CI Head & Base, CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia) for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Filter Feed Pumps Make:KIRLOSKER / WILLO Capacity : 30 m3/hr Head : 30 M RPM : 2900 (1 working+ 1 Standby)

Treated Water Transfer Pumps Make:KIRLOSKER / WILLO Capacity : 40 m3/hr each Head : 40 M RPM : 2900 (1 working+ 1 Standby)

Providing, fixing, testing & commissioning of vertical MSEP filter with adequate dirt holding capacity. Fabricated from MS as per manufacturer's specifications complete with intitial charge filter media including painting inside with two coats of non toxic epoxy and with one coat of zinc chromate two coats of synthetic enamel paint outside. Including concrete foudation with cement plaster complete as required. The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves etc. Make : KWT/3SW/Doshion Multigrade Filter. Filteration Rate : 15000 LPH Capacity : 30 m3/hr

Activated Carbon Filter Filteration Rate : 15000 LPH Capacity : 30 m3/hr

Supplying, installing, testing & commissioning of hypochlorite solution doser comprising of 100 Litres capacity FRP/HDPE tank with inlet / outlet connection, piping & valves alongwith metering (0-6 lph) pump for dosing.

Make: Prominent/ Walkton/Grundfos: Supply, installation, testing and commissioning of Centrifuge of Suitable Capacity Centrifuge feed pump (Screw Type) – 2 No. (1 working + 1 standby) , interconnecting piping and poly dosing system.

Centrifuge Make : Alfa Laval/KWT/Humboldt: Supply, installation, testing & commissioning of Electro-magnetic type Flow Meter at inlet of reactor tanks and Outlet of ACF .

Make : Walkton/Forbes Marshall/ Hach: Providing & fixing on line pH meter digital type for Monitoring the online pH after Tertiary treatmnent & before disposal. Including electrical wiring from panel to flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect.Make: 3SW/Forbes Marshall/ Hach

SEWAGE TREATMENT PLANT (MOVING BED BIO REACTOR TECHNOLOGY) Design, supplying, installing, testing & commissioning of Sewage Treatment Plant (excluding excavation, back filling & disposal of surplus earth MS/Civil construction work) for the following duty: Nature of effluent - Domestic Sewage from toilet, kitchen waste water shall be discharged into the STP. Design to take consideration of same. Daily average flow - 200 Cum / Day pH - 7.5 – 8.5 BOD5 - 250 – 400 Mg/L S. Solids - 200 – 450 Mg/L COD - 400 – 600 Mg/L T Nitrogen- Less than 35 Mg/L Phosphorus -Less than 10Mg/L Oil & Grease - 50 Mg / L Effluent discharge standard after treatment pH - 6.5 – 8.5 BOD5 - Less than 10Mg/L S. Solids - Less than 10 Mg/L COD - Less than 60 Mg/L T Nitrogen- Less than 10 Mg/L Phosphorus -Less than 2 Mg/L Oil & Grease - Less than 10 Mg / L Sewage treatment plant shall include the following items: Screen Chamber - 1 no. Oil and Grease Trap - 1 no. Sewage equalization tank / sump - 1 no. Anoxic Tank-1 No. MBBR Tank - 2 nos. (equal capacity each) Tube Settler - 1 no. (with lamina clarifier) CC Tank - 1 no. Sludge Holding Tank - 1 no. UF Feed water Tank - 1 no. Filtration through MGF & ACF Treated Water Tank UF Unit Air Blowers, Pumps & equipment Piping, valves etc Electrical Panel & Cabling Note: Contractor shall ensure submission of detailed GA drawings (Plan & Section), P&I diagram, schematic diagram for the above said component and additional component if so required for the complete working of the STP for the full capacity. Supply, installation, testing & commissioning of 2 Nos Stainless Steel Perforated, Corrugated Bar Screen with suitable lifting arrangement (size 600 mm wide x 600 mm high approx)

Make : KWT/3SW/Ecologix: Supply, installation, testing & commissioning of level switch for automatic operation of the system complete with auxillary NO/NC contacts for each tank.

Make : Minilec/ Pune Techtral Supply, installation, testing & commissioning of non clogging type submersible pumps complete with all accessories, CED Coating, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Provison shall be kept to run both pumps simultaneously in case of emergency. Pumps shall have following duty: Make: EBARA/GRUNDFOS Submersible Sewage Pumps for transfer of Raw Sewage in EQT (1 working & 1 standby) :- Flow rate (each) = 40 m3/hr each Head = 8-12 Mtr MOC : CI (Solid handling size for this pump shall be 20-30 mm).

Make : Minilec/ Pune Techtral Supply, installation, testing & commissioning of non clogging type submersible pumps complete with all accessories, CED Coating, motor of required capacity. Delivery header with isolation valve, pressure gauge on delivery line with isolation cock, level controller (with wiring) to control the level of sump automatically. Provison shall be kept to run both pumps simultaneously in case of emergency. Pumps shall have following duty: Sludge recirculation pump (2 Nos - 1 working + 1 Standby) Flow rate (each) = 30 m3/hr Head = 8-12 Mtr MOC : CI (Solid handling size for this pump shall be 7 mm).

Plant room sump pump (2 Nos - 1 working + 1 Standby) Flow rate (each) = 44 m3/hr each Head = 8-12 Mtr (Solid handling size for this pump shall be 15 mm). Provision of guide ropes to guide submersible pump from upper level to operational level in sump basin with channels / angle section of MSEP shall be made by the STP contractor.

Air diffusion system shall include the following: 2 Nos. twin type rotary air blowers (1W + 1S) capable of delivering 550 cum/hr of free air at 0.5 kg/cm2 driven through “V” belt or directly coupled through flexible coupling to a TEFC motor of suitable HP Suitable for 415 ± 10% volts, 3 phase, 50 cycles AC supply.

Make : BETA/EVERAST/KEY Air piping shall comprise of pipes droppers / laterals with MSEP (''C'' Class) Header complete with all fittings such as tees, crosses, plugs, sockets, elbows, reducers, supports & clamps, puddle flanges etc cutting chases & making good. Contactor to submit detailed P & I indicating their proposal

Non clog type air dispersion system capable of handling 3-5 cfm of air with oxygen transfer efficiency of 3-4% per/meter water depth. Air dispersion grid shall be assembled in modular form so that they can be replaced / repaired easily from plat form at the top. (Imported fine bubble membrane diffusers)

Make :Rehau / Walkton/EDI: Bronze Ball valve and air dispersion grid as required for STP as described above. Note : Air dispersion system shall be provided for Sewage Sump, aeration tank and Sludge Holding Tank.

Providing and fixing all piping (as described below) and isolation control valves for making the system complete. SS 304 : Submerged air piping MS Epoxy : Air piping & pumped effluent riser (non-submerged) MSEP piping : Pumped effluent (submerged) & tank overflow pipe line MSEP : Interconnecting pipe line after delivery header of pump/ filter

Supply, installation, testing and commissioning of package type Ultra Filtration system of suitable capacity for Flushing water of 200 KLD capacity complete with pre-treatment system comprising of UF hollow fibre membranes, high pressure pumps (1W+1S)), chemical dosings, backwash pumps (1W+1S), piping, valves, pressure gauges, etc complete. The unit shall have all interlocking for safe operation of plant. The unit shall have skid mounted electrical panel complete with required starters and shall also have all Annuanciation and Controls. Indication instrumentation shall also be provided. PLC with input/output modules shall be integrated with all auto equipments/ valves in auto mode. System Integrator Make: KWT/3SW/Ecologix

Supply, installation, testing and commissioning of MBBR media of suitable capacity as per manufacturer recommendation to be installed in MBBR reactor Tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps.

Make : Cooldeck/MM Aqua/Perfectus: Supply, installation, testing and commissioning of PVC tube deck settling media to be installed in Secondary Tube Setller tank alongwith suitable sludge removal arrangement either by pumps or air lifting pumps .

Make : Alfa/Sukruit/Perfectus: Supply of Anoxic mixer

Supplying, installing, testing & commissioning of horizontal centrifugal water pumps CI Head & Base, CI Impeller along with motor, pressure gauge with isolation cock, Isolation valve, NRV on delivery line. Isolation valve, stainer (with by-pass) at suction. Mechanical seal, suitable vibration elimination pads of approved design, drain pipe with valve (25 dia) for the pump. The pump shall be suitable for 415±10% volts 3 phase AC supply. Filter Feed Pumps Make:KIRLOSKER / WILLO Capacity : 45 m3/hr Head : 30 M RPM : 2900 (1 working+ 1 Standby)

Treated Water Transfer Pumps Make:KIRLOSKER / WILLO Capacity : 50 m3/hr each Head : 40 M RPM : 2900 (1 working+ 1 Standby)

Providing, fixing, testing & commissioning of vertical MSEP filter with adequate dirt holding capacity. Fabricated from MS as per manufacturer's specifications complete with intitial charge filter media including painting inside with two coats of non toxic epoxy and with one coat of zinc chromate two coats of synthetic enamel paint outside. Including concrete foudation with cement plaster complete as required. The filter shall also be provided with set of internals for raw water inlet and bottom collecting system. Complete with frontal piping (heavy) and butterfly valves etc. Make : KWT/3SW/Doshion Multigrade Filter. Filteration Rate : 15000 LPH Capacity : 45 m3/hr

Activated Carbon Filter Filteration Rate : 15000 LPH apacity : 45 m3/hr

Supplying, installing, testing & commissioning of hypochlorite solution doser comprising of 100 Litres capacity FRP/HDPE tank with inlet / outlet connection, piping & valves alongwith metering (0-6 lph) pump for dosing.

Make: Prominent/ Walkton/Grundfos: Supply, installation, testing and commissioning of Centrifuge of Suitable Capacity Centrifuge feed pump (Screw Type) – 2 No. (1 working + 1 standby) , interconnecting piping and poly dosing system.

Centrifuge Make : Alfa Laval/KWT/Humboldt: Supply, installation, testing & commissioning of Electro-magnetic type Flow Meter at inlet of reactor tanks and Outlet of ACF .

Make : Walkton/Forbes Marshall/ Hach Providing & fixing on line pH meter digital type for Monitoring the online pH after Tertiary treatmnent & before disposal. Including electrical wiring from panel to flow meter. Complete with all type of Plumbing & Electrical connections, accessories, wiring, conduits & supports complete with all respect.

TUBE WELL: Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer -in-charge, upto 90 metre depth below ground level.All types of soil 300 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia,conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.200 mm nominal size dia

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conformingto IS: 12818, including hire & labour charges, fittings & accessories etc.all complete, for all depths, as per direction of Engineer-in-charge.200 mm nominal size dia

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineerin- charge.

Providing and fixing factory made precast RCC perforated drain covers, having concrete of strength not less than M-25, of size 1000 x 450x50 mm, reinforced with 8 mm dia four nos longitudinal & 9 nos cross sectional T.M.T. hoop bars, including providing 50 mm dia perforations @ 100 to 125 mm c/c, including providing edge binding with M.S. flats of size 50 mmmm x 1.6 mm complete, all as per direction of Engineer-in-charge.

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by “V” notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.200 mm clamp

Providing and fixing Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).200 mm dia

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :50 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :50 mm nominal bore

Supplying & installation of submersible pump set directly coupled with 5 HP motor nominal speed 2900 RPM suitable for operation on 3-phase, 50 cycles, 400 + 5% volts A.C. power supply to give yield of 6000 LPH at a head of 50 mtrs. Total head = 60 Mt Flow rate = 9000 LPH H P = Minimum 5 HP (Or as per site condition)

Supply & installation of 80 mm dia column pipe made out of 80 mm dia GI including the cost of fittings complete in all respect Jindal, Hissar/Prakash make 'B' class pipe.

PART (A) ELECTRICAL INTERNAL WORKS GMC & TEACHING HOSPITAL: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab Group C

Wiring for twin control light point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed steel conduit, 2 way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab Group C

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.Make : anchor, Havels , Polycab

Wiring for light/ power plug with 4X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed steel conduit alongwith 2 Nos. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.Make : anchor, Havels , Polycab

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 2 X 6 sq. mm + 1 X 6 sq. mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 4X6 sq.mm + 2X6 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 4X10sq.mm + 2X 6 sq.mm earth wire

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required.Make : anchor, Havels , Polycab 4 X 16 sq. mm + 2 X 6 sq. mm earth wire

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 2X1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed heavy duty PVC conduit ISI Mark, with modular switch, modular plate, Blanking Plate if equired suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab Group C (One point controlled by one switch)

Wiring for twin control light point with 2 X 1.5 sq.mm FRLS PVCinsulated copper conductor single core cable in surface / recessed heavy duty PVC conduit ISI Mark, 2 way modular switch, modular plate,suitable GI box and earthing the point with 1.5 sq.mm. FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab

Wiring for group controlled (looped) light point/fan point/exhaust fan point/ call bell point (without independent switch etc.) with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed PVC conduit, and earthing the point with 1.5 sq. mm FRLS PVC insulated copper conductor single core cable etc. as required.Make : anchor, Havels , Polycab Group C ( Two point controlled by One switch)

Circuit wiring for power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed 2mm thick Heavy duty PVC conduit ISI Mark alongwith 1 No 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.Make : anchor, Havels , Polycab

Circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single corecable in surface/ recessed heavy duty PVC conduit ISI Mark as requiredMake : anchor, Havels , Polycab 2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire (For Light ckt.)

Circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single corecable in surface/ recessed heavy duty PVC conduit ISI Mark as requiredMake : anchor, Havels , Polycab 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire (UPS Computer wiring)

Circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single corecable in surface/ recessed heavy duty PVC conduit ISI Mark as requiredMake : anchor, Havels , Polycab 2 X 6 sq. mm + 1 X 6 sq. mm earth wire (For power DBs ckt.)

Circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single corecable in surface/ recessed heavy duty PVC conduit ISI Mark as requiredMake : anchor, Havels , Polycab 4X6 sq.mm + 2X6 sq.mm earth wire (For UPS & Light DBs ckt.)

Circuit/ submain wiring alongwith earth wire with thefollowing sizes of FRLS PVC insulated copper conductor, single corecable in surface/ recessed heavy duty PVC conduit ISI Mark as requiredMake : anchor, Havels , Polycab 4X10sq.mm + 2X 6 sq.mm earth wire (For+Power DBs ckt)

Supplying and drawing co-axial TV cable RG-6 grade, 0.7 mm solid copper conductor PE insulated, shielded with fine tinned copper braid and protected with PVC sheath in the existing surface/ in heavy duty PVC ISI Mark conduit as required.

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.Make : anchor, Havels , Polycab 20 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.Make : anchor, Havels , Polycab 25 mm

Supplying and fixing of following sizes of steel conduit along with accessories in surface/recess including painting in case of surface conduit, or cutting the wall and making good the same in case of recessed conduit as required.Make : anchor, Havels , Polycab 32 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface recess including cutting the wall and making good the same in case of recessed conduit as required. 25 mm

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface recess including cutting the wall and making good the same in case of recessed conduit as required. 32 mm

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. Telephone socket outlet

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required. TV antenna socket outlet

RJ-45 Internet socket for Cat 6

Supplying and fixing following size/ modules, GI box alongwith modular base & cover plate for modular switches in recess etc. as required.1 or 2 Module (75mmX75mm)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch, connection etc. as required. (For light plugs to be used in non residential buildings).

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 amps modular socket outlet and 15/16 amps modular switch, connection etc. as required.

SITC of 1200 mm LED Recess Linear Fixture with Body made of Extruded Aluminium Alloy Housing with Prismatic Diffuser and PDC/Aluminium End Caps. System Efficacy>100 lpw( System Lumens > 3600 lm) complete with all accessories. CRI >80, CCT of 4000/5700K. The Fixture should not be more than 70mm in width . .Minimalistic Design with Wide Distribution.Avg life of 50,000 Burning Hours @L70.High efficiency driver with inbuild surge protection of 2.5kV. Inbuilt Driver Protection against over voltage protection, short circuit , Miswiring and Reverse Polarity. THD < 10%,PF>.95. Operating Voltage Between (140-270)V. (BIS Approved). Submission of LED Photo biological safety report confirming to 62471 and from LED source manufacturer & LM79 report from NABL accrediated laboratory) ) Havells cat - DESTELLO Recess 36 w or Equivalent Makes of Philips/Wipro/Panasonic

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required(FOR INTERNET & INTERCOM).

Supplying and fixing suitable size/module GI box with modular plate and cover in front on surface or in recess, including providing and fixing 3 Nos. 3 pin 5/6 Amp modular socket outlet and 1 No. 16 Amp modular switch, connection, painting etc. as required (For computer power applications). ( For Computer point)

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providng and fixing 2 nos. 3 pin 5/6 Amodular socket outlet and 2 nos. 5/6 A modular switch, connections etc. as required. (For light plugs to be used in non residential buildings).

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 100/63 A, 16 KA,TPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 100/63/40 Amp, 30KA, FPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 125 A,36KA,FPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 200 A,36KA,FPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 250 A,50KA,FPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 400A,50KA,FPMCCB

Providing and fixing following rating and breaking capacity and 4 pole MCCB in existing cubicle panel board including drilling holes in cubicle panel, making connections, etc. as required (D.N series).Make : 630 A,50KA,FPMCCB

Supplying and fixing following way, horizontal type three phase and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 4 way (4 + 12), Double door

Supplying and fixing following way, horizontal type three phase and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 6 way (4 + 18), Double door

Supplying and fixing following way, horizontal type three phase and neutral, sheet steel, MCB distribution board, 415 volts, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) 8 way (4 + 24), Double door (For power ckt. DBs + Light Load ckt. DB & UPS DBs )

upplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 200 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCB TPDB is normally used where 3 phase outlets are required.) 4 way (4 + 12), Double door

Supplying and fixing of following ways surface/ recess mounting, vertical type, 415 V, TPN MCCB distribution board of sheet steel, dust protected, duly powder painted, inclusive of 250 A tinned copper bus bar, common neutral link, earth bar, din bar for mounting MCBs (but without MCBs and incomer ) as required . (Note : Vertical type MCCB TPDB is normally used where 3 phase outlets are required.)Make : anchor, Havels , Polycab 4 way (4 + 12), Double door WITH PROVISION OF MCCB 200 A 4P

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab Single pole

Supplying and fixing 5 amps to 32 amps rating, 240/415 volts, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab Triple pole

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 40 amps 4P

Supplying and fixing following rating, four pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 63 amps 4P

Supplying and fixing following rating, THREE pole, 415 volts, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab MCB TP 63A 10 KA

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 40 A

Supplying and fixing following rating, double pole, (single phase and neutral), 240 V, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 63 A

Supplying and fixing 25 amp. Starter and 1 no. 25 Amp 6 pin socket outlet with 4 module GI box in recess i/c connections, earthing etc as required.

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 40A

Supplying and fixing following rating, four pole, (three phase and neutral), 415 volts, residual current circuit breaker (RCCB), having a sensitivity current 30 mA in the existing MCB DB complete with connections, testing and commissioning etc. as required.Make : anchor, Havels , Polycab 63A

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioningetc. as required. Make : anchor, Havels , Polycab

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Providing and fixing H.T. danger notice plate of 250 mm X 200mm, made of mild steel, at least 2 mm thick, and vitreous enameled white on both sides, and with inscription in single red colour on front side as required.Make : anchor, Havels , Polycab

Supplying, installation, testing & commisioning of following capacity End Feed Unit for the existing Air Insulated Compact Type bus trunking/Sandwich Type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick steel sheet enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with necessary joints including clamping brackets, angle iron bracket, steel fasteners, connecting to earthing system etc. as requiredMakes :legrand ,obo betterman, Honeywell. 400 A 30kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ Sandwich Type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 125 A 15kA SC for 1 sec

Supplying, installation, testing & commisioning of following capacity Plug In/ tap off box on the existing Air Insulated Compact Type bus trunking/ Sandwich Type rising mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply made with 1.6mm thick sheet steel enclosure (IP54) duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete etc. as required 200 A 25kA SC for 1 sec

Supplying, installing by suspension on ceiling, testing and commissioning of following capacity Sandwich Type Rising Mains for use on 3 phase 4 wire 415 volts, 50Hz A.C. supply with metal clad enclosure having IP-54 rating after fixing the tap off boxes and all accessories, made of 1.6mm thick steel sheet duly powder coated in convenient sections complete with 4 Nos aluminium bus bars having current density of 130 A/ sq cm at nominal current rating, necessary joints, elbow joints & expansion joints and bends, fire barrier at each floor, provision of tapping at every metre, adopter box and copper flexible for joints, continuous earthing with 2 Nos aluminium strip of suitable size (one on each side) including, G.I. clamping brackets, suspenders, angle iron bracket, steel fasteners, connecting to earthing system etc. as required 400 A 25kA SC for 1 sec

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.Makes :legrand ,obo betterman, Honeywell. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.Makes :legrand ,obo betterman, Honeywell. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.Makes :legrand ,obo betterman, Honeywell. 150 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated painted with powder coating M.S. cable trays bends with perforation not more than 17.5%,, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc as required.Makes :legrand ,obo betterman, Honeywell. 200 mm width X 50 mm depth X 1.6 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.Makes :legrand ,obo betterman, Honeywell. 375 mm width X 62.5 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray (Galvanisation thickness not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.Makes :legrand ,obo betterman, Honeywell. 750 mm width X 75 mm depth X 2.0 mm thickness

Supplying and installing following size of perforated Hot Dipped Galvanised Iron cable tray "bends" (galvanisation not less than 50 microns) with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended fromthe ceiling with G.I. suspenders including G.I. bolts & nuts, etc. as required.Makes :legrand ,obo betterman, Honeywell. 750 mm width X 75 mm depth X 2.0 mm thickness

EARTHING Supply of Earthing termination made of copper-bonded rod of 10 feet length,17.2 mm dia. (Minimum copper bonding shall be 0.25mm) is CPRI tested for 25 KA fault current, UL Listed complying code IS 3043:2018, IEEE-80, IEC 62561-2 along with Rod-to-Conductor connectors, 50 kg, Earth enhancement material Jam Lite with (resistivity less than 0.12 Ωm) complying code IEC 62561-7, IS 3043-2018, NBC 2016, Ply Plastic Pit Cover Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/ coke and salt as required.

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Earthing with copper earth plate 600 mm X 600 mm X 3 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm copper strip in 40 mm dia G.I. pipe earth electrode including connection with brass nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and laying earth connection from earth electrode with 6 SWG dia G.I. Wire in 15 mm dia G.I. pipe from earth electrode including connection with G.I. thimble excavation and re-filling as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm copper strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

5.16 Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Providing and fixing 4.00 mm dia copper wire on surface or in recess for loop earthing as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recessfor loop earthing along with existing surface/ recessed conduit/submain wiring/ cable as required.

Providing and fixing earth bus of 50 mm X 5 mm copper strip on surface for connections etc. as required.

LIGHTNING ARRESTOR : Air Termination Network: Providing and fixing of lightning conductor finial, made of 25 mm dia 300 mm long, G.I. tube, having single prong at top, with 85 mm dia 6 mm thick G.I. base plate including holes etc. complete as required.

Fixing of lightning conductor finial (single prong) with base plate including holes etc. complete as required.

Jointing copper / G.I. tape (with another copper/ G I tape, base of the finial or any other metallic object) by riveting / nut bolting/ sweating and soldering etc as required.

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For horizontal run)

Providing and fixing G.I. tape 20 mm X 3 mm thick on parapet or surface of wall for lightning conductor complete as required.(For vertical run)

Providing and fixing testing joint, made of 20 mm X 3 mm thick G.I. strip, 125 mm long, with 4 nos. of G.I. bolts, nuts, chuck nuts and spring washers etc. complete as required.

Providing and laying G.I. tape 32 mm X 6 mm from earth electrode directly in ground as required.

Supply, installation, testing and commissioning of Lightning Strike counter Model: JMV 7D for counting the number of lightning strikes without any power supply. The Counter should be mounted on the Down Conductor. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Surge Protection Devices: Supply, installation, testing and commissioning of Class B/Type I Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of ≤ 2.5 kV. Response Time should be less than 100 ns. The maximum impulse test current should be 50 kA (10/350 µs) per pole and 100 kA (10/350 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Supply, installation, testing and commissioning of Class C/Type II Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of ≤ 1.5 kV. Response Time should be less than 25 ns. The maximum impulse discharge surge current should be 20 kA (8/20 µs) per pole and 40 kA (8/20 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Supply, installation, testing and commissioning of Class C/Type II Single Phase Surge Protection Devices as per IEC 62305-4 and tested according to IEC 61643 – 11, DIN Rail mountable with Maximum Continuous Operating Voltage of 320 V and Voltage Protection Level of ≤ 1.5 kV. Response Time should be less than 25 ns. The maximum impulse discharge surge current should be 20 kA (8/20 µs) per pole and 40 kA (8/20 µs) neutral to protective earth. The surge protection devices shall be enclosed in polycarbonate enclosure of IP 65 rating. Make: JMV or equivalent model of ERICO, OR FURSE, OBO.

Raceway: Supply and fixing of following sizes triple compartment under floor trunking made out of 1.6mm thick pregalvanised sheet steel complete with all accessories and fixing accessories as per site requirement all as required & specified. (i) 225mm x 38mm x 1.6mm (3 compartment). Make - OBO, LEGRAND. MK-HONEYWELL.

Supply and fixing of following sizes double compartment under floor trunking made out of 1.6mm thick pregalvanised sheet steel complete with all accessories and fixing accessories as per site requirement all as required & specified. (ii) 300mm x 38mm x 1.6mm (3 compartment) . Make - OBO, LEGRAND. MK-HONEYWELL.

Supply and fixing of following sizes triple compartment under floor trunking made out of 1.6mm thick pregalvanised sheet steel complete with all accessories and fixing accessories as per site requirement all as required & specified. (i) 150mm x 38mm x 1.6mm (2 compartment) . Make - OBO, LEGRAND. MK-HONEYWELL.

Supply, installation, testing & commissioning of under floor Junction over box of size 250mm x 250mm x 60-75mm one trap 3 compartment with metal lid and suitable for 225mm x 38mm/150mmx38mm depth three/double compartment metal raceway made out of high pressure diecast zinc alloy complete with all accessories such as top cover base support frame, base support stud etc. complete as required. Make - OBO, LEGRAND. MK-HONEYWELL.

Supply, installation, testing & commissioning of under floor Junction over box of size 350mm x 350mm x 60-75mm one trap 3 compartment with metal lid and suitable for 300mm x 38mm/225mmx38mm/150mmx38mm depth three/double compartment metal raceway made out of high pressure diecast zinc alloy complete with all accessories such as top cover base support frame, base support stud etc. complete as required. Make - OBO, LEGRAND. MK-HONEYWELL.

Supply, installation, testing & commissioning of under floor Access Outlet box of size 250mm x 250mm x 60-75mm one trap 3 compartment suitable for 225mm x 38mm/150mmx38mm depth three/double compartment metal raceway made out of high grade pre-galvanized GI sheet to prevent any corrosion. The base has a sheet thickness of 1mm, provison for maximum of 14 modules, trap lid is made of high grade GI epoxy coated with an 8mm recess to accommodating carpet/tiles complete, 12mm spacers are provided for wiring space, Robust die cast pillars on 4 corners, Load bearing capacity upto 4.5Kn with deflection of 1.48m with all accessories such as top cover base support frame, base support stud etc. complete as required. Make - OBO, LEGRAND. MK-HONEYWELL.

Supply, installation, testing & commissioning of vertical access box box of size 250mm x 200mm x 50mm 2 compartment suitable for 225mm x 38mm/150mmx38mm depth three/double compartment metal raceway. Make - OBO, LEGRAND. MK-HONEYWELL.

Supply, installation, testing and commissioning of 8M POP UP Box Concealed mounted, bottom box side screw to install including Panel, Lid, Side plate of bottom box, Socket amounting frame with Brushed oxidation surface. Pure metal surface cover & Metal painting bottom base. Make - OBO, LEGRAND. MK-HONEYWELL.

Floor panel For Light and UPS Load Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. ENCLOSURE & ACCESSORIES Fabrication in 2.0 mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 200A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. Light and UPS load INCOMER FEEDER MCCB 100A FP 25KA. TM Based =1NO. Spreader Links =1SET METERING SET Voltmeter with VSS =1NO. Ammeter with ASS =1NO. RYB Indication Lamp LED =3NO. 100/5Amp. 15 VA CL-1 Current Transformer =3NO. 06Amp. Control SP MCB. =3NO. CT Short Link =3NO. OUTGOING FEEDER MCCB 40A. FP 25KA. TM Based =5NO. Spreader Links =5 Sets. MCCB 63A. FP 25KA. TM Based =2NO. Spreader Links =2 SETS. Dummy =2NO.

POWER LOAD FLOOR PANEL Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. ENCLOSURE & ACCESSORIES Fabrication in 2.0mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 300A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. INCOMER FEEDER MCCB 200A. FP 36KA TM Based =1NOS Spreader Links =1 SET Extended Rotary Handle =1NOS METERING SET Voltmeter with VSS =1NOS Ammeter with ASS =1NOS RYB Indication Lamp LED =3NOS 100/5Amp. 15 VA CL-1 Current Transformer =3NOS 06Amp. Control SP MCB. =3NOS CT Short Link =3NOS OUTGOING FEEDER MCCB 40A. FP 25KA. TM Based =2NO. Spreader Links =2 SETS MCCB 63A. FP 25KA. TM Based =5NOS Spreader Links =5SETS Dummy =2NOS

40 KVA UPS PANEL Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. ENCLOSURE & ACCESSORIES Fabrication in 2mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 200A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. INCOMER FEEDER MCCB 125A. FP 36KA =2NO. Spreader Link =2SET. Extended Rotary Handle =2NO. Voltmeter with VSS =2NO. Ammeter with ASS =2NO. RYB Indication Lamp LED =6NO. 125/5Amp. 15 VA CL-1 Current Transformer =6NO. 06Amp. Control SP MCB =6NO. CT Short Link =6NO. OUTGOING FEEDER MCCB 40A. FP 30KA . For G.F UPS DB-1 = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 40A. FP 30KA . For F.F UPS DB-1,2 = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. MCCB 40A. FP 30KA . For S.F UPS DB-1,2 = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. MCCB 40A. FP 30KA . For 3RD.F UPS DB-1,2 = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. MCCB 40A. FP 30KA . For Spare = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. Dummy =2NO.

Supply, Installation, testing & commissioning of Set 1x40 KVA UPS. Each UPS of 40KVA/40KW should have the following specification in addition to tender requirements. True online Double conversion, IGBT Rectifier & Inverter based UPS Three phase Input / Three phase output with 12V SMF Batteries suitable for 30min backup on Full load at 0.8 Load P.F. with minimum Battery Bank VAH is 36000VAH with each UPS. Input Voltage operations on mains without switch over to battery : 400 VAC +/-20% (320V - 480V) at 100% load, Input Power factor 0.99 @ 100% linear load, input THdi less than 5% @ 100% linear load, Output THdv is less than 2% for full linear load & less than 5% for non - linear load. Crest factor 3:1, Overload 125% for 10min, 150% for 1 min. Battery flexible design shall be available for at least 4 no. of batteries . Battery type should be 12V SMF ,Valve Regulated Lead Acid. Inbuilt Delta - Star Input Isolation Transformer, Parallel communication Port, RS232, USB, EPO , SNMP interface & BMS interface. Dust filter at Air Inlet point are required. UPS should be provided with Surge protection device /TVSS and phase sequence protection & correction device . UPS should be with LCD touch display indicating all important parameters. UPS shall be provided with External Battery open rack with top cover battery interlinks, battery breaker, battery to UPS cable as required should be provided with UPS systems, UPS system shall be parallelable utp 4 units in case required in future. Each UPS shall be compatible for working redundant mode with other. Approved Make - Eaton/ Legrand-Numeric/Schneider Electric/Emerson -Vertiv.

75 KVA UPS PANEL: Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. ENCLOSURE & ACCESSORIES Fabrication in 2mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 300A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. INCOMER FEEDER MCCB 200A. FP 36KA =2NO. Spreader Link =2SET. Extended Rotary Handle =2NO. Voltmeter with VSS =2NO. Ammeter with ASS =2NO. RYB Indication Lamp LED =6NO. 200/5Amp. 15 VA CL-1 Current Transformer =6NO. 06Amp. Control SP MCB =6NO. CT Short Link =6NO. OUTGOING FEEDER MCCB 100A. FP 25KA =4NO. Spreader Link =4SET MCCB 63A. FP 25KA =1NO. Spreader Link =1SET. MCCB 40A. FP 25KA. TM Based =2NO. Spreader Links =2SET Dummy =2NO.

Supply, Installation, Testing and Commissioning of 75 kVA Modular UPS . Each UPS of 75KVA/75KW should have the following specification in addition to tender requirements. UPS with modular configuration having Hot swappable power module capacity ranges from 5KW to 10 KW for maximum redundency with high performance IGBT based fully microprocessor controlled ( three phase Input & three phase Output) online UPS system suitable for input and output parameters as per specifications. The UPS shall be provided in powder coated fan cooled enclosure suitable for min75 KW capacity frame painted in colour as per specifications. The UPS shall be suitable for normal, emergency, recharge, by-pass and maintenance mode including bypass arrangement with microprocessor based display and control panel. The UPS shall have 12V SMF Batteries Bank suitable for 30min backup on Full load at 0.8 Load P.F. with minimum Battery Bank VAH is 72000VAH . UPS should also have following features :Inbuilt Phase sequence protection & correction feature , Each Power Modules should have HOT SWAPPABLE feature , Built in Automatic & Maintenance Bpass Switch and Emergency Power Off (EPO) Feature Should be available. Complete system shall be provided as per specifications, approved drawing and as per site requirement including interconnecting cables from battery to UPS, UPS to panel with single core copper cabling as per manufacturer recommendation etc. Approved Make - Eaton/ Legrand-Numeric/Schneider Electric/Emerson -Vertiv.

30 KVA UPS PANEL Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. ENCLOSURE & ACCESSORIES Fabrication in 2mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 200A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. INCOMER FEEDER MCCB 100A. FP 36KA =2NO. Spreader Link =2SET. Extended Rotary Handle =2NO. Voltmeter with VSS =2NO. Ammeter with ASS =2NO. RYB Indication Lamp LED =6NO. 100/5Amp. 15 VA CL-1 Current Transformer =6NO. 06Amp. Control SP MCB =6NO. CT Short Link =6NO. OUTGOING FEEDER MCCB 40A. FP 30KA . For G.F UPS DB-1,2 = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. MCCB 40A. FP 30KA . For F.F UPS DB-1,2 = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. MCCB 40A. FP 30KA . For Spare = 2 NO. Spreader Link = 2 NO. Rotary Handle = 2 NO. Dummy = 2 NO.

Supply, Installation, testing & commissioning of Set 1x30 KVA UPS. Each UPS of 30KVA / 27KW should have the following specification in addition to tender requirements. True online Double conversion, IGBT Rectifier & Inverter based UPS Three phase Input / Three phase output with 12V SMF Batteries suitable for 30min backup on Full load at 0.8 Load P.F. with minimum Battery Bank VAH is 28800VAH with each UPS. Input Voltage operations on mains without switch over to battery : 400 VAC +/-20% (320V - 480V) at 100% load, Input Power factor 0.99 @ 100% linear load, input THdi less than 5% @ 100% linear load, Output THdv is less than 2% for full linear load & less than 5% for non - linear load. Crest factor 3:1, Overload 125% for 10min, 150% for 1 min. Battery flexible design shall be available for at least 4 no. of batteries . Battery type should be 12V SMF ,Valve Regulated Lead Acid. Inbuilt Delta - Star Input Isolation Transformer, Parallel communication Port, RS232, USB, EPO , SNMP interface & BMS interface. Dust filter at Air Inlet point are required. UPS should be provided with Surge protection device /TVSS and phase sequence protection & correction device .UPS should be with LCD Screen display indicating all important parameters. UPS shall be provided with External Battery open rack with top cover battery interlinks, battery breaker, battery to UPS cable as required should be provided with UPS systems, UPS system shall be parallelable utp 4 units in case required in future. Each UPS shall be compatible for working redundant mode with other. Approved Make - Eaton/ Legrand-Numeric/Schneider Electric/Emerson -Vertiv.

LIFT PANEL Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. ENCLOSURE & ACCESSORIES Fabrication in 2mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 200A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. INCOMER FEEDER MCCB 125A. FP 36KA TM Based =1NO. Spreader Link =1SET . Rotary Handle =1NO. Voltmeter with VSS =1NO. Ammeter with ASS =1NO. RYB Indication Lamp LED =4NO. 06Amp. Control SP MCB =4NO. 125/5Amp. 15 VA CL-1 Current Transformer =4NO. CT Short Link =4NO. OUTGOING FEEDER MCCB 63A. FP 30KA . For LIFT NO.1,2,3 = 3 NO. Spreader Link = 3 NO. Rotary Handle = 3 NO. MCCB 63A. FP 30KA . For Spare = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. Dummy = 2 NO.

POWER PANEL Supply, installation, testing and commissioning of powder coated of Siemens grey of approved colour compartmentlised cubicle MV Panel fabricated out of 14 SWG thick CRCA sheet steel suitable for operation on 415 Volts, 50Hz, 3 Phase 4 wire AC supply . The panel shalll be indoor free standing, floor mounting, dust and vermin proof type, adeqate size cable alley with front operated rotary handles for MCCB's complete with gland plates, lifting hooks, ventillating louvers, busbars, Inter connections, earthing, labelling electrical , as per specification and drawings, suitable for termination of cables as per single line diagram including. supply and fixing of following switchgear and accessories complete as required. A separate earth copper bus bar of size 25 mm x 5 mm to be provided throughout the length of the panel. The Panel should be extendable type. (Make of panel, Tricolite, International Switchgear, Embit ,Kalyani switchgear). Having CPRI test certificate breaking capacity 70 KA and ISO 9001-2008. Note:- The cost of MCCBs, etc. are not included in the panel's cost and shall be paid under separate head. All acccessories included in the panel cost such as MCBs, ACB , rotary handles, Spreader link and its accessories & metering etc. The panel should be got inspected / tested in the factory premises from the Engineer-in-charge / consultant before brought at site after approval of all drawings of the panel. ENCLOSURE & ACCESSORIES Fabrication in 2.0mm.CRCA Sheet Powder Coating in Siemens Gray Shade, Cable Entry will be Top & Bottom Suitable for Cable ,Lock, Rubber Gasket, hardware etc. BUS BAR & HARDWARE 300A. Aluminium Main Bus Bar,Load wise Sub Feeder Bus Bar Colour Coated Heat Shrink Bus Bar sleave Nut-Bolt,Washer ,Hardware etc. WIRING & ACCESSORIES Power & Control Wiring will be (ISI 1100V) flamc smoke FRLS PVC Single Core Copper Wire,Copper Lugs, PVC Sleeve, Ferruels Numbers, Hardware & Labour etc. INCOMER FEEDER MCCB 200A. FP 36KA TM Based =1NOS Spreader Links =1 SET Extended Rotary Handle =1NOS METERING SET Voltmeter with VSS =1NOS Ammeter with ASS =1NOS RYB Indication Lamp LED =3NOS 200/5Amp. 15 VA CL-1 Current Transformer =3NOS 06Amp. Control SP MCB. =3NOS CT Short Link =3NOS OUTGOING FEEDER MCCB 63A. FP 30KA . For PDB G.F = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 63A. FP 30KA . For PDB F.F = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 63A. FP 30KA . For PDB S.F = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 63A. FP 30KA . For PDB 3RD.F = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 63A. FP 30KA . For KITCHEN = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. MCCB 63A. FP 30KA . For Spare = 1 NO. Spreader Link = 1 NO. Rotary Handle = 1 NO. Dummy = 2 NO.

FANS & FIXTURES Supply, installation, testing and commissioning of 12W, SURFACE/Recess Mounted LED Down Light,polycarbonate Cover with high purity aluminum housing, with opal PC diffuser for uniform low glare light and PC reflector to enhance product light output,System Lumen of 1200Lm, CRI>80, 5700K, THD<10%, PF>0.95, IP20, IK03, ,Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ,Internal Surge Protection:2.5 KV; Average lifeL70: 50000 hours.Protection : Reverse Polarity, Open & Short Circuit,driver safety requirement standards :is 15885-2-13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source,fixture to be BIS certified. including cost of all petty materials required to complete the job in all respect. Havells ,Panasonic, Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 36W LED 2'X2' SURFACE Mounted panel Luminaire with housing made up of CRCA powder coated white after phosphochromate treatment with optics made up of High transmittance opal diffuser. Powered by Isolated, SELV output Electronic Driver with Output Short-circuit protection, Surge Voltage protection and other safety & performance test as per IS:15885 Part 2/Sec 13 & Consumption should not greater than 36W and System Efficacy 120 L/W Lumens/Watt, System Lumen -4320 Lumens or more ,PF>0.95, CRI>80 ,THD<10%. Operating temperature: -10 °C to +45 °C , 45 mm height & teperred housing on the edge, Primary and secondary optics with secondary lens and diffuser. Operating voltage range: 140 V - 270 V, Average lifeL70: 50000 hours. Luminaire Should conform to IP20 Classification. Test report to be submitted; photo biological safety norms: IS16108, test certificate to be submitted; certification: LM 79 for luminaire and LM80 for led source, Driver and Fixture to be BIS certified., Plano TAPS. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: integra nxt PLANOX2PLR36WLED857TAPS or Panasonic,Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 15W, SURFACE Mounted LED Down Light,polycarbonate high purity aluminum housing, with opal PC diffuser for uniform low glare light and PC reflector to enhance product light output,System Lumen of 1500Lm, CRI>80, 5700K, THD<10%, PF>0.95, IP20, IK03,Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ,Internal Surge Protection:2.5 KV; Protection : Reverse Polarity, Open & Short Circuit,driver safety requirement standards :is 15885-2-13, test report to be submitted; photo biological safety norms: is 16108, test certificate to be submitted; certification: lm 79 for luminaire lm 80 for led source,fixture to be BIS certified. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: Integra next INTEGRANXTRDDLRSURD15WLED865S orPanasonic, Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 20W integrated batten , Made of Aluminum Extrusion with housing part in Anodized finish & diffuser part in reeded opal finish. Lumen Output of 2200 lumens with System efficacy of > 110lm/W .CRI >80, Color temperature 6500K, THD <10% and PF>0.95, IP20 . Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:2 KV; Protection : Reverse Polarity, Open & Short Circuit. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: LUMILINE 20W or Panasonic, Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 10W integrated batten , Made of Aluminum Extrusion with housing part in Anodized finish & diffuser part in reeded opal finish. Lumen Output of 1100 lumens with System efficacy of > 110lm/W .CRI >80, Color temperature 6500K, THD <15% and PF>0.95, IP20 . Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:2 KV; Protection : Reverse Polarity, Open & Short Circuit. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: LUMILINE or Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of Heavy duty bulkhead reccess or surface type lighting fixture (ramp light) 9-10W made up of pressure die-cast aluminium housing and Polyster Powder coated die cast aluminium with High quality polycarbonate diffuser in opal finish for glare free light distribution.High efficiency long life LED module with SMD LED package mounted on MCPCB with lumen efficacy of >95 lm/W with system lumen 950. Powered by integral electronic LED driver with APFC with low THD Output short/open circuit Protection. CCT 5700, CRI>80, System Efficacy>90Lm/W, THD<15%, PF>.95, IP66,IK 10, Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; DRIVER PERFORMANCE REQUIREMENTS: IS 16104, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE.Hexa. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: HEXAFT10WLED857SSYMBOPC orPanasonic, Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 9 W LED spike light, Pressure die-cast aluminium housing for sturdiness, excellent corrosion resistant and efficient thermal management grey finish. Clear poly carbonate cover is provided for maintaining ingress protection. High efficiency long life LED SMD with Ra>80, and narrow beam angle to ensure better uniformity of light distribution. ensures zero maintenance, No UV & IR radiations, Environment friendly as it does not contain Mercury, Instant light with low running temperatures, Operating Temp. range: -10°C to +45°C, Average life L70B50: 50000 Burning hours. IP66, IK:07, System Lumen:630, CCT:3000K. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: LYCUSSPS9WLED730PSYMBOTG or Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of Wall Light suitable for LED lamp with E27 holder. including cost of all petty materials required to complete the job in all respect. Wipro Cat. LM91-L180- or Panasonic,Equivalent in Philips & Havells.

Supply, installation, testing and commissioning of 70 W Endura Sundown Streetlight Pressure die-cast aluminium alloy for housing (heat sink) for effective thermal management, sturdiness, excellent corrosion resistant, separate optical and control gear compartment & Bottom opening for easy maintenance.Long life & photobiologically safe LED’s.High performance potted electronic driver ensures zero maintenance.No harmful UV & IR radiations,Environment friendly as it does not contain Mercury,Instant light with low running temperatures,Operating temperature: -10 °C to + 50 °C,Operating voltage range: 100 V - 300 V,Average life L70B50: 50000 hours, CCT 6500K, System Lumen 7700LM, THD<10%, PF>0.95, Tempered protective toughened glass, thermal shock and impact resistant fixed to the housing with SS screws. Asymmetrical batwing light distribution. Powered by built-in potted LED driver (SMPS based constant current supply) with lower THD, Output Open / Short Circuit protection, Phase to Phase protection (Operation at 440 V AC), Over Voltage protection, Surge Voltage protection upto 6 kV & other safety test as per IS 15885 Part-2/ Sec 13.IP66 protection and impact resistance of IK07. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: NDURASUNDOWNSL70WLED765PASYBOGT or Panasonic,Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 5W LED Spike Light Luminaire with housing made up of Gray pure polyester powder coated , Pressure die-cast spike, snoot and aluminium housing for efficient thermal management, sturdiness.Optics made up Prismatic chrome plated reflector for controlled beam angle of 60° and cover made up of High quality toughened glass in clear finish for uniform light distribution. Powered by an Built-In potted, electronic driver (SMPS based constant current supply) with lower THD, Output Open/ Short circuit protection, Surge voltage protection upto 4kV & other safety test as per IS:15885 Part 2/Sec 13. Power Consumption not greater than 5W and System Lumens ranging from 36Lumens to 3000 Lumens depending on CCT- 3000K, PF>0.9, CRI>80for 3000K CCT,THD<15%. Operating temperature: up to +50 °C , Operating voltage range: 140 V - 270 V, Average lifeL70: 35000 hours. Luminaire Should conform to IP66 and IK07 Classification. Test report to be submitted; photo biological safety norms: IS16108, test certificate to be submitted; certification: LM 79 for luminaire and LM80 for led source, Driver and Fixture to be BIS certifi. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: IRVINSPS5WLED830PSYMTG or Panasonic,Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 40W LED Postop made of Pressure die-cast Aluminium housing as well as spigot for sturdiness , Clear Poly Carbonate cover for symmetric light distribution, System wattage : 40W, IP rating – IP 66 & IK rating – IK 08 , CCT – 5700K and 3000K (3000K would be launched later) / CRI > 80, System Lumen Efficacy : 100lm/w (5700K), SPD External – 10kV (DM/CM), Unique design and shape, it can be offered with our Deco and Eco pole. Operating temperature:- upto 50 °C, Operating voltage range: 140 V - 270 V, Average life L70B50: 50000 hours. Powered by Built In potted, isolated electronic LED driver with APFC (SMPS based constant current supply) with lower THD, Output Short / Open, Circuit protection, Over Voltage protection, Surge Voltage protection upto 10 kV with SPD & other safety test as per IS 15885 Part-2/Sec 13. THD<10%, PF>0.95, CRI>80, Suitable for pole mounting with OD of 76 mm max with 3 nos. allen screw M6 X 20 mm provided with the fixture. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: NEBULAPT40WLED857PSYMTPMC orPanasonic, Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 15W LED Wall mount UP DOWN Luminaire with housing made up of Gray pure polyester powder coated ,Pressure die-cast aluminium .Optics made up of High quality toughened glass in clear finish for uniform light distribution Upward & downward light ratio- 50:50 and high impact resistance IK07 . Powered by an Built-In potted, electronic driver (SMPS based constant current supply) with lower THD, Output Open/ Short circuit protection, Surge voltage protection upto 4kV & other safety test as per IS:15885 Part 2/Sec 13. Power Consumption not greater than 25W and System Lumens not less than 2500 Lumens,CCT 3000K, PF>0.95, CRI>80 ,THD<10%. Operating temperature: up to +45 °C , Operating voltage range: 140 V - 270 V, Average lifeL70: 50000 hours. Luminaire Should conform to IP66 and IK07 Classification. Test report to be submitted; photo biological safety norms: IS16108, test certificate to be submitted; certification: LM 79 for luminaire and LM80 for led source, Driver and Fixture to be BIS certified. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: CLIOWLS15WLED830PSYMTOTG or Equivalent in Wipro and Philips .

Supply, installation, testing and commissioning of 40W LED All-in-One Solar Streetlight with System efficacy not less than 150 lm/W. System lumen o/p not less than 6000 lumens. 60Wp High Efficiency Monocrystalline Silicon Panel. 36Ah LiFePO4 Battery with higher life of >2000 cycles. At Full Power ≥10Hrs autonomy and at Saving mode ≥30Hrs autonomy. Automatic Dusk to Dawn feature. Integral PIR sensor for motion detection. MPPT charge controller with 90-96% efficiency. System voltage: 12V. LEDs used in the product shall comply with EN 62471 for Photo-biological safety and certificate for the same from manufacturer shall be provided. Luminaire shall be with IP65 protection. The LED shall be compliant with LM80-08 standard with L70 life of 50000 Hrs tested at maximum current (Complete LM 80 test report for LED should be submitted for 10000 hrs of testing). The LEDs used should be with CCT of 5700 K and CRI >70. including cost of all petty materials required to complete the job in all respect. Panasonic,Wipro or Equivalent in Philips and , , GE . (Warranty of 3years.

Supply, installation, testing and commissioning of 5000 mm Decorative pole with galvanised Mild steel tubes having 114 mm dia at bottam and 60/75 mm dia at top with cast Al embellishment q3 with service window containing 6-amp MCB, 4-way connector terminal of 25 Amp , pole is with caste embellishments at middle & bottom. including cost of all petty materials required to complete with primer coated and painted with polyrethane paint in all respect i.c CC foundation of 1:2:4 of size 0.6mx 0.6mx 1.20 deep , MS foundation bolt M16 dia x 18" hot dip galvanized L- type boundation bolt and MS check nuts . Wipro or Equivalent in Philips and ,Panasonic , K-LITE , Twinkle Luxmax Cat No. Luxmax-Steel-114-502(114- Base) embellishment. . (Warranty of 3years).

Supply, installation, testing and commissioning of Modern 40 watt decorative gear mounting Street light made of cast aluminum housing with power LED,s & extruded aluminum heat sinks. A UV stabilized PC/PMMA diffuser is provided for glare free lighting with high visual comfort. Available in 3000k/6000k. including cost of all petty materials required to complete the job in all respect. Wipro or Equivalent in Philips and ,Panasonic , K-LITE , Twinkle Luxmax CAT NO. LUXMAX-PT-151- S . (Warranty of 3years).

Supply, installation, testing and commissioning of Architectural LED Floodlight 85 W+/- 1 W c constructed from aluminium die cast Hosuing.Tempered Frosted Step Glass cover with High Purity Lens with IP Protection of IP66The Input voltage range shall be 150V to 270V with Electrical Insulation Class 1.Fixture have Surge Protection 3kV with 3000 K.Fixture should have beam angle of 40 degree fixture should have IK rating of Minimum IK08 and Should be BIS approved.ncluding driver,connector and all accessories as per site . including cost of all petty materials required to complete the job in all respect. Wipro or Equivalent in Philips and , , GE . (Warranty of 3years).

Supply, installation, testing and commissioning of of 1000mm Linear wall washer 40 +/- 1 W with system efficacy with CC driver for proper driving of LEDs With Extruded Aluminium Housing(powder coated).Tempered Frosted Step Glass with IP Protection of IP66.The LED shall be tested with LM80-08 standard with Useful life of 50000 Hrs at L70. The Input voltage range shall be 150V to 270V .Fixture have beam angle of 30 degree. Including driver,connector and all accessories as per site .Including driver,connector and all accessories as per site . including cost of all petty materials required to complete the job in all respect. Wipro Cat No. LF01-361-030-30-10 orPanasonic Equivalent in Philips and , , GE . (Warranty of 3years).

Supply, installation, testing and commissioning of Architectural LED Inground Light 8 +/- 1 W with CV driver for proper driving of LEDs constructed from aluminium die cast (powder coated).Tempered Frosted Step Glass with IP Protection of IP67. The Input voltage range shall be 150V to 270V .Fixture have Surge Protection 2.5kV with 2700K CCT .Fixture have beam angle of 15/30 degree.Including driver,connector and all accessories as per site including cost of all petty materials required to complete the job in all respect. WiproCat No. LF05-600-036-27-XX or Equivalent in Philips and , , GE . (Warranty of 3years).

Supply and Erection of Hot Dip Galvanized octagonal pole of 3 mm thickness, with base plate including cost of nut and bolts and all accessories as supplied by the manufacture including cost of foundation accessories etc. The foundation bolts as per manufacturer design should be hot dipped galvanized pole complete with door locking arrangement, Terminal plate consisting of 2 nos. 100 Amp.., 4 pole neutral links including connection etc. with suitable connecting arrangements for 2 No. MCB's / Kit-Kat including cost of R.C.C 1:1, 5:3 for foundation of size 0.7 M x 0.7 M x 1.8 M with minium 8 Nos. 12 mm dia longitudinal MS reinforcement rods with rings of 8 mm dia not more than 200 mm C.C for fixing the pole with all labour and material required to complete the job in all respect upto the entire satisfaction of Engineer in Charge of the work. 7 Mtr. Long pole with top dia 70 mm and bottom dia 130 mm with base plate of size 220 mm x 225 mm x 12 mm.

Supply, installation, testing and commissioning of 20W integrated batten , Made of Aluminum Extrusion with housing part in Anodized finish & diffuser part in reeded opal finish. Lumen Output of 2200 lumens with System efficacy of > 110lm/W .CRI >80, Color temperature 6500K, THD <10% and PF>0.95, IP20 . Life class of 50,000 hrs @ L70, Operating Temperature:-10 TO +45 DEG.C; Input Supply Voltage Range:140-270 V, Frequency :50-60 HZ; Internal Surge Protection:2 KV; Protection : Reverse Polarity, Open & Short Circuit. DRIVER SAFETY REQUIREMENT STANDARDS :IS 15885-2-13, TEST REPORT TO BE SUBMITTED; PHOTO BIOLOGICAL SAFETY NORMS: IS 16108, TEST CERTIFICATE TO BE SUBMITTED; CERTIFICATION: LM 79 FOR LUMINAIRE LM 80 FOR LED SOURCE. including cost of all petty materials required to complete the job in all respect. Havells Cat Ref: LUMILINE 20W or Panasonic, Equivalent in Wipro and Philips .

Supply, Installation, Testing and Commissioning and erection of HEAVY DUTY EX. FAN 380MM-15’’ with Louvre complete with shutter (ISI mark) including cost of petty material required to complete the job in all respect. (Make Make : Make Anchor,Crompton, Havells)

Supplying, installation, testing and commissioning of A.C. CEILING FAN 48" (1200MM) Rating with BLDC, Energy efficient including cost of petty material required to complete the job in all respect. Make : Make Anchor,Crompton, Havells).

Supplying, installation, testing and commissioning of A.C. CEILING FAN 56" (1400MM) Rating with BLDC, Energy efficient including cost of petty material required to complete the job in all respect. Make : Make Anchor,Crompton, Havells).

Supply, Installation, Testing and Commissioning and erection of FRESH AIR fan 10'' heavy duty 900 rpm with Louvre complete with shutter (ISI mark) including cost of petty material required to complete the job in all respect. (Make Anchor,Crompton, Havells )

Supply, Installation, Testing and Commissioning and erection of wall fan complete with shutter (ISI mark) including cost of petty material required to complete the job in all respect. (Make Anchor,Crompton, Havells)

Rank Projects and Development Pvt Ltd

KEC International Limited