TN_No_39 Const. of proposed U.N. Brahma Cultural Complex at Dudhnoi, P.O.- Dudhnoi in Goalpara District.

Amount

Earth Work Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (A) Up to a depth of 2.00m below the existing ground level. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand : 8 coarse aggregate by volume

Providing and laying 25mm thick damp proof course with cement concrete in prop 1:1.5:3 with graded stone agg.of 10mm down nominal size including providing approved damp proof admixture in proportion as recommended by the manufacture including curing etc. complete as directed.

R.C.C Works Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth.

(B) In super structure from plinth level up to 1st floor level. N) Without using admixture, plasticiser b) M20 grade concrete or prop. 1:1.5:3. ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral, staircase and landing) including preparing the top surface and finishing of nosing. b) M20 grade concrete or Prop. 1:1.5:3.

Plain cement concrete floor base in prop 1:3:6 laid in alternate bays as specified with coarse agg. Of size 13mm to 32mm including dewatering if necessary, and curing etc.complete. B) 50mm thick

Form Work Providing form work of ordinary timber planking so as to give a rough fininsh including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Sides of tie beams, grade beams etc. at or below ground level. (b) Using 25mm thick plank

Columns, Pillars, Posts & Strut (a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc.having plane vertical face (ii) Using 25mm thick plank

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal (a) For depth not exceeding 1.0M. (i) Using 38mm thick plank. (ii) Using 25mm thick plank

(b) For depth exceeding 1.0M (Using 38mm thick plank). Flat Surfaces such as soffits of suspended floors, roofs, landings, cantilever slabs, chajjas, balconies and the like. (a) Floors etc. upto 200mm in thickness. (i) Using 38mm thick plank. (ii) Using 25mm thick plank.

Staircase with sloping or stepped soffits including risers and stringers but excluding Landing. (Using 38mm thick plank) (ii) Using 25mm thick plank

Brick Work Providing soling in foundation and under floor with stone/best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a) Brick on flat soling.

Brick work in cement morter with 1st class brick including racking out joints and curing complete as directed. (c ) In proportion 1:5.

1st class brick nogged wall in cement motar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separtately). (A) 112mm thick brick wall (b) In cement mortar in proportion 1:5.

Flooring & Skirting 65mm thick cement concrete floor consisting of 50mm under layer of cement concrete in prop. 1:3:6 (1cement :3 coarse sand : 6 coarse aggregate of 25mm and down) and 15mm thick wearing layer in cement concrete in prop. 1:1:2 (1 cement :1 coarse sand : 2 coarse aggregate of size 10mm down) laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @ 2.75kg. per square metre of floor area) including curing etc. complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (b) 15mm thick

Providing Ceramic Tiles of approved quality, size, shape and thickness not less than 8mm of floors, skirtings, treads and risers of steps over cement morter bed 15mm thick in prop. 1:3 (1 cement :3 coarse sand) including cutting where necessary finished with flush pointing with fix-A Tile Choksey/ Sika/Pedelite/Rouf/White cement slurry mixed with approved pigment to match the shade of granite slab, complete at all levels as specified and directed (coloured pigment should be in conformity with colour of slab and as approved and directed by the Department). Normal range Of size 300mm x 300mm and above

Providing polished ceramic wall tiles of approved quality, size, shape and thickness not less than 8mm on walls and skirtings over cement mortar bed 10mm thick in prop. 1:3 (1 cement : 3 coarse sand) including cutting where necessary finished with flush pointing with fix-A-Tile (Choksey /Sika/Pedelite/Rouf) white cement slurry mixed with approved pigment to match shade of tiles complete at all levels as specified and directed. (Cement plastering to be measured and paid separately). (Coloured pigment should be in conformity with colour of tiles and as approved and directed by the Department). (Walls means both interior and exterior walls). ii) Of size 200mm x 300mm and above

Plastering 10mm thick cement plaster in single coat on fair side of brick/concrete walls for interior plastering up to 1st floor level including arises or rounded angles not exceeding 80mm girth and finished even and smooth including curing complete as directed. D) In cement mortar 1:6.

B) On fair side d) In cement mortar 1:6

Roofing Providing Pre Painted Galvanized Iron Sheet (PPGI) accessories (Ridges/Valley/Gutter/Flashing) at all levels including fitting and fixing self drilling, self tapping screws complete complete. TATA Blue scope/Dyna roof/Durakolor/Wonder Roof or equivalent as directed by the Department. (iv) 0.60mm thick

Wood Work Providing wood work in frame (chowkaths) of doors, windows, clerestory windows and other similar works wrought, framed and fixed in position in contact with C.C or brick masonry wall including supplying, fitting and fixing with M.S hold fast (40mm x 3mm x 250mm) as per design embeded in cement concrete block in proportion 1:2:4 and with two coats of kiricide oiling to the timber faces in contact with C.C and masonry as directed and specified. (a) With sal wood

Providing, fitting and fixing full panelled doors/windows including oxidised M.S butt hinges (100mm x 75mm x 3.55mm) with necessary screws (other fittings to be measured and paid separately. A) With Teak Wood / Sissu wood. (ii) 35mm thick

M.S Gril Providing, fitting and fixing M.S grill of required pattern for windows/clerestory windows/openingwith M.S flats at required spacing in frame all round, square or round M.S bars with round headed bolts and nuts or screws. II. Ornamental grill (c ) Fixed to Brick work/P.C.C/R.C.C.

Ceiling Providing and fixing, in position suspended false ceiling using E-Grid (exposed ceiling suspension 2430 system) of grid size 600mm x 600mm/1200mm x 600mm with main runner 38 x 24mm, cross tee 29mm x 24mm & wall angle 24mm x 24mm. Using 4mm/6mm thick High Pressure Steam Cured Non Asbestos Fibre Cement Board as per IS 14862, to be placed in a grid of G.I system duly suspended with 4mm/6mm dia G.I/M.S bar hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures, air conditioning diffuser and ducts, sprinklers, smoke detectors etc. The main runners to be secured to structural soffit by hanger @ 1220mm maximum c/c. The last hanger at the end of each main runner should not be placed at more than 450mm from the adjacent wall. Flush fitting 1220mm cross tee to be interlocked between main runners @ 610mm c/c, so as to form 600mm x 600mm/1200mm x 600mm grid, all complete as per the drawing & directions of engineer-in-charge. Finally, if specified boards are to be painted with 2 coats of acrylic emulsion paint of approved shade/make over a coat of cement primer before installing it on the grid. (A) Standard Ceilings of everest make or equivalent as directed by the department. (ii) Using 6mm thick FC Board.

Providing, fitting and fixing anodised aluminium sliding windows and ventilators of standard sections of approved brand without horizontal glazing bars, joints mitred and welded (manufactured to relevant IS specifications) and providing and fixing handles, angle cleat, rubber gasket, roller, bolting device, locking arrangements screws etc as required complete as specified and directed for all levels. (b) 3 Track sliding window (i) 6mm clear glass

CEMENT PAINT & PRIMER a) Applying one coat of cement primer of approved brand and manufacture on new wall surface after throughly brooming the surfaces free from mortar droppings and of her foreign matter and including preparing the surface even and papered smooth.

Finishing wall with two coats of acrylic emulsion exterior coatings of Unicem "Rakshak" brand of required shade by thining 1ltr. Of paint with 750ml of water to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials as specified and directed by the department.

Wall Putty Work & Painting Providing two coats of J.K Wall Putty (White Cement based putty for concrete/morter walls and ceiling both internal and external) after removing all loosely adhering materials from the wall surface with the help of emery stone, putty blade or wire brush and moistening the wall with sufficient quantity of clean water as specified and directed by the department. (Total thickness of two coats is maximum 1.5mm).

Wall painting (two coats) with acrylic emulsion paint approved brand and manufacture (Asian paint/Berger paint/ICI paint/J & N paint/Nerolac) on new surface to give an even shade after throughly brushing the surfaces free from mortar droppings and other foreign matter and sand papered smooth. (a) Acrylic Emulsion Paint approved brand and manufacture (Asian paint/Berger paint/ICI paint/J

Wood Primer & Painting Applying priming coat over new wood and wood based surfaces over 100mm in girth/width after and including preparing the surface by throughly cleaning oil, grease, dirt and other foreign matter, sand papering and knotting. (b) With ready mixed paint, wood primer (white).

Painting one coat (excluding priming coat) on old wood based surfaces with enamel paint to give an even shade including cleaning the surface of all dirt, dust and other foreign matter sand papering and stopping. (i) Surfaces over 100mm in width or girth. b) High gloss (Asian paint/Berger paint/ICI paint/J&N paint/Nerolac).

Door Fittings Supplying, fitting, fixing anodised aluminium fittings of approved make, reasonably smooth, free from sharp edges and corners, flawd and other defects and with counter sunk holes for screws including necessary aluminium screws etc. complete.(anodised to bright & satin finished). a) Sliding door bolts i) 300mm x 16mm

b) Tower bolts ii) 250mm x 12mm

iii) 200mm x 12mm

c) Door handles iii) 150mm

Supplying, fitting and fixing in position reinforcement bars conforming to relevent I.S code for R.C.C work/ R.B walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc.complete. (No extra measurement for lap, hook, chair, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level). a) From Primary Producer: TATA/SAIL/Esser Steel/Jindal steel/Shyam steel/RINL (ii) Super Ductile (SD) TMT reinforcement bars

Providing, fitting, hoisting and fixing of roof trusses fabricated out of combination of any two or all of the following sections (i) Square section (ii) Rectangular Hollow section of specification RSH/SHS and (iii) M.S circular hollow section of Grade 210 including purlins, bottom runners and providing M.S cleat, M.S angle base plank, bolts and nuts with red oxide primer including fitting bottom runner and cleat etc. for fixing ceiling joist as per design complete as directed as per specifications. a) Using TATA make RHS/SHS of Grade 310 conforming to relevant I.S code 4923: 1997

Providing and fixing in position collapsible M.S. shutters with vertical channels 20mm x 10mm x 2mm braced with flat iron diagonals 20mm x 5mm size with top and bottom rails of T-iron 40mm x 40mm x 6mm with 38mm dia steel pulleys complete with bolts and nuts, locking arrangements, stoppers, handles including applying a priming coat of red lead paint.

Providing plinth protection 50mm thick to cement concrete 1:3:6 with coarse agg. Of 20mm nominal size including finishing the surface with 10mm thick cement plaster in propotion 1:3 with a floting coat of neat cement finished.

Providing drain with cement concrete (1:3:6) 10cm thick sides 10cm thick bed over brick flat soling inclduing 15mm thick cement plastering in prop. 1:3 finished with a floating coat of cement slurry as directed with necessary shuttering for sides and earth work in excavation of foundation trenches and refilling the sides after completion of work etc. as specified. i) 300mm wide and average 150mm deep with bed slope 1 in 150 with initial depth of 100mm.

ii) 300mm wide and average 250mm deep with bed slope 1 in 150 with initial depth of 100mm.

Earth Work Earthwork in excavation for foundation trenches of walls, retaining walls, footings of column, steps, septic tank etc. including refilling (return filling) the quantity as necessary after completion of work, breaking clods in return filling, dressing, watering and ramming etc. and removal of surplus earth with all lead and lifts as directed and specified in the following classification of soils including bailing out water where necessary as directed and specified. (a) In ordinary soil.

Plain cement concrete works with coarse aggregate of sizes 13mm to 32mm in foundation bed for footing steps, walls, brick works etc. as directed and specified including dewatering if necessary, and curing complete (shuttering where necessary shall be measured and paid separately). (b) In prop 1cement: 4 sand : 8 coarse aggregate by volume

Providing and laying plain/reinforced cement concrete works cement, coarse sand & 20mm down graded stone aggregate including dewatering if necessary, and curing complete but excluding cost of form work and reinforcement for reinforced cement concrete work (form work and reinforcement will be measured and paid separately). (I) Using Mixer Machine (A) In substructure up to plinth level Foundation, footing, columns with base tie and plinth beam, pile cap, base slab, retaining walls, walls of septic tank, inspection pit and the like and other works not less than 100mm thick up to plinth. N) Without using admixture, plasticiser a) M15 grade concrete or Prop. 1:2:4

ii) Columns, pillars, posts, struts, suspended floor, roof, landing, shelf and support, balcony, lintel, sill band, beam, girder, bressumer, cantilever, staircase (except spiral, staircase and landing) including preparing the top surface and finishing of nosing. N) Without using admixture, plasticiser a) M15 grade concrete or Prop. 1:2:4.

Providing form work of ordinary timber planking so as to give a rough fininsh including centering, shuttering, strutting and propping etc., height of propping and centering below supporting floor to ceiling not exceeding 4.0M and removal of the same for in situ reinforced concrete and plain concrete work in: Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. 3.1.1.1 Foundation, footings, bases of columns, pile cap, raft and mass concrete works etc. (b) Using 25mm thick plank

Columns, Pillars, Posts & Strut (a) Square, Rectangular, polygonal in plan or any shape like Tee/L etc.having plane vertical face (ii) Using 25mm thick plank

Sides and Soffits of Beams, beam haunchings, cantilever girders, bressumers, lintels and horizontal tie. (a) For depth not exceeding 1.0M. (ii) Using 25mm thick plank

Flat Surfaces such as soffits of suspended floors, roofs, landings, cantelever slabs, chajjas, balconies and the like. (b) Floors etc. above 200mm in thickness (Using 38mm thick plank).

Brick Work Providing soling in foundation and under floor with stone/ best quality picked jhama brick, sand packed and laid to level and in panel after preparing the subgrade as directed including all labour and materials and if necessary dewatering, complete. (a).Brick on flat soling.

Brick work in morter with 1st class brick including racking out joints and curing complete as directed. (c ) In proportion 1:5.

1st class brick nogged wall in cement motar including racking out joints and curing complete as directed in super structure above plinth up to 1st floor level (protruding M.S rod/Tor steel of column to be embeded in cement mortar and will be measured and paid separately) (A) 112mm thick brick wall (a) In cement morter in proportion 1:4.(1 cement"4 sand)

65 mm thcik cement concrete floor consisting of 50 mm under layer of cement concrete in prop. 1:3:6 (1 cement : 3 coarse sand : 6 coarse aggregate of 25mm and down) and 15 mm thick wearing layer in cement concrete in prop. 1:1:2 (1 cement ; 1 coarse sand : 2 coarse aggregate of size 10mm down0 laid in panels and finished with a floating coat of neat cement finish (using cement slurry for bond @2.75 kg. per square metre of floor area) including curing etc. complete as directed.

Cement plaster skirting with cement mortar in prop. 1:3 (1cement : 3 coarse sand) finished with a floating coat of neat cement including rounding of junctions with floor. (a) 15 mm thick.

15 mm thick Cement plaster in single or half brick wall for interior plastering up to 1st floor level including arises, internal rounded angles, not exceeding 80mm girth and finished even and smotth including curing complete as directed. A) On rough side b) In cement mortar 1:4

b) Finishing wall with water proofing cement paint of approved brand and manufacture and of required shade on new wall surface (two coats) to give an even shade after throughly brooming the surfaces to remove all dirt and remains of loose powdered materials.

Supplying, fitting and fixing in position reinforcement bars conforming to relevant I.S. Code for R.C.C work/ R.B. walling including straightening, cleaning, cutting and bending to proper shapes and length as per details, supplying and binding with 20G annealed black wire and placing in position with proper blocks, supports, chairs, spacers etc. complete. (No extra measurement for lap, hook, chairs, anchor etc. will be entertained in the measurement as they are included in the rate) (Upto 1st floor level) a) From Primary Producer: TATA/SAIL/Esser Steel/ Jindal steel/Shyam steel/RINL (i) TMT Corrosin resistant steel (CRS) reinforcement bar

Deep Tube Well Labour for boring hole for Inserting tube well pipes through different soil/ rock media including hire charges of drill, pipes, scaffolding, tools and plants as necessary and taking out the same and lowering pipes, fittings complete as directed by the department. i) Bore hole of 75mm diametet

Supplying, fitting and fixing pipes plain/bevel ended for casing, conforming to relevant IS codes of practice including supplying and fitting of tube well accessories, lowering of assembly pipes concentrically in the borehole followed by supplying and packing of pea gravel free from dirt, dust and other foreign materials in the annular space between the borehole and assembly pipes complete as directed by the Department. PVC PINE SUPREME/PRINCE / FUSION/SFMC Brand...... iii) 75mm diameter

Supplying fitting and fixing ISI approved PVC filter 3.00 metre long. iii) 80mm diameter

Development of the tube well with compressor or by over pumping unit for 48 hours till sand free discharge is obtained

Supplying, fitting and fixing suction pipes plain/bevel ended, conforming to relevant IS codes of practice including supplying and fitting of accessories, lowering of assembly pipes concentrically in the casing pipes complete as directed. B) PVC PIPE SUPREME / PRINCE / FUSION /SFMC Brand iii) 40mm diameter

Wooden planking in flooring including fixing to wooden base frame with necessary wood-screws complete (base of the wooden frame to be measured and paid separately.) 2000 Lt capacity (a) Sintex make

Labour for erecting and placing PCVC Tank over stagging up to a height of 5.00m complete as directed. (a) 2000 litre capacity

Internal Sanitary & Water Supply Providing fitting and fixing vitreous water closet squatting pan (Indian type W.C. Orissa pattern) with all fittings and fixtures complete including cutting and making good to the walls and floors wherever required. (Flushing Cistern to be paid separately). 1.1.2 Indian type Orissa pattern of size 500mm a) White ii) Hindware make

Supplying, fitting and fixing PVC flushing cistern with all internal fittings with CI brackets including fitting and fixing standard size CP flush pipe, union clamps etc. complete as directed and specified (pipes will be measured separately). ii) Hindware make a) White

Providing fitting and fixing vitreous china flat back type lipped front urinal basin with standard flush pipe and CP brass spreader and brass unions, etc. complete including painting of fittings and brackets, cutting and making good the walls & floors wherever required. (B) Hindware Make a) White

Providing vitreous China wash basin with CI/MS brackets, C.P brass chain with plug, PVC waste pipe including painting of fittings and brackets, cutting and making good the walls wherever required. (Pillar cock, stop cocks, waste coupling are to be paid separately). ii) Hindware make a) White (i) CEDER 570 x 440 (Cat. No.91049/91115)

Providing fitting and fixing Decorative Mirror complete as directed and specified. (A) Parryware Make (b) Size 600mm x 450mm

Providing, fitting and fixing recessed soap tray / soap dish complete as directed and specified. (i) Jaquar Make (a) Continental (Cat.No.ACN-1331N)

Supplying, fitting and fixing PVC pipes of 6 Kg/cm2 (Supreme/Prince) or other ISI approved including joining, fitting and fixing wiyh clamps etc.as necessary complete at all levels including below G.L as directed and specified. A) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75mm dia.

Supplying, fitting and fixing 87.5 degree PVC bend of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. A) In exposed surfaces or in trenches. (ii) 110mm dia.

b) Concealed by chiselling or breaking brick wall/C.C/R.C.C and making good to the damages. (ii) 110mm dia.

Supplying fitting and fixing PVC Plain single tee of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. A) In exposed surfaces or in trenches. (ii) 110mm dia.

Supplying fitting and fixing PVC single tee with door of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. A) In exposed surfaces or in trenches. (ii) 110mm dia.

(iv) 75mm dia.

Supplying fitting and fixing PVC reducer of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. as necessary complete at all levels including below G.L as directed and specified. A) In exposed surfaces or in trenches. (ii) 75mm dia.

Supplying fitting and fixing PVC socket plug of (Supreme/Prince) or other ISI approved including joining, fitting and fixing etc. in exposed surface or trences as necessary complete at all levels including below G.L as directed and specified. (a) 110mm dia.

(b) 75mm dia.

Providing fitting and fixing PVC cowel of ISI make complete as directed and specified. (iv) 75mm dia. PVC cowel of ISI make

C.P Grating (ii) 110mm dia

Providing fitting and fixing 450mm dia. 90mm thick C.I Man hole cover and frame of 19 Kg. weigh complete as directed and specified.

Construction of filter bed in soak pit including earth work in excavation of soil and then filling up of the trench with brick bats/Charcaol covered with earth over a layer of A.C plain sheet above brick bat filling complete as directed. (sizes of soak pit may very depending on the sizes and capacities of the septic tank as well as the number of users as mentioned in the table.

Construction of inspection pit inside measurement 450mm x 450mm x 450mm flush with 100mm dia meter HCI/PVC pipes and cement concrete base in proportion 1:3:6 over flat brick soling, 12cm brick wall in cement mortar in proportion 1:4 finished with 13mm cement plaster in proportion 1:2 in side wall and floor 450mm x 450mm air tight C.I inspection pit cover and frame complete including supplying of materials, necessary excavation of pit as directed.

WATER SUPPLY Supplying fitting and fixing approved PVC Pipes of different sizes, with all necessary 'R' brand or similar approved P.V.C fittings such as bend, tee, elbow, reducer, nipple, plug, long screw fitting, clamps etc. complete at all levels including below G.L as directed and specified. (A) Exposed or in trenches SUPREME/PRINCE/SFMC BRAND or other equvalent approved brand (High presure pipe Sch-40) b) 40mm dia

b) 32mm dia

(B) Concealed by chiselling or breaking brick wall/ C.C wall /R.C.C wall and making good to the damaged structure. SUPREME /PRINCE/SFMC/FUSION BAND or other equvalent approved brand (High presure pipe Sch-40) c) 32mm dia

e) 20mm dia

Supplying fitting and fixing C.P bib cock 15mm dia of approved brand directed and specified. (G.I) & C.P pipes will be measured separately). Essco make (Dulux/Sumthing spl. (b) Long body bib cock with wall flange

Supplying fitting and fixing chrome plated (C.P.) stop-cock of approved brand and size as mentioned below as directed and specified. (G.I. & C.P pipes will be measured and paid separately). (a) Continental /Clarion (ii) 15mm dia (Angular stop cock)

Supplying and fitting fixing C.P pillar cock of 15mm dia of approved brand as specified and directed. (b) Long neck with areator

Supplying and fitting gun metal country pit valve (full way valve) I.S.I make as specified and directed. B) 40mm dia.

c) 25mm dia.

Supplying fitting and fixing Pipes with all necessary fittings in exposed or in trenches including trenching and refilling the same etc complete as directed. B) PVC pipe with PVC fittings (Using PVC high pressure pipe) x) 110mm diameter

Earth Work Raising low site around the building with approved soil by, truck carriage including breaking clods, dressing etc. complete with payment of land compensation for obtaining earth from private land, Govt. land etc. b) Other than Guwahati City

Electrification Wiring for light/fan/call bell point with 2x1.5 sq mm P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel/Nicco/Anchor or equivalent Make as approved by the Deptt.) with flat 19mm ISI marked casing 'n' capping (AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) in surface system, including 6 Amp flush type switch/bell push (Anchor Penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) GI/MS switch board (ISI marked) half conceal on wall with phenolic laminated sheet cover, ceiling rose (Anchor/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) etc. complete as directed and specified by the Deptt. 1) Short point up to 3.00 metre. lenght.

2) Medium point up to 6.00 metre. Length

3) Long point up to 10.00 metre. Length.

Wiring for drawing sub-main line with 2x1.5 sq mm P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kable/Nicco/Anchor or Equivalent Make as approved by the Deptt.) in surface flat 19mm ISI marked casing 'n' capping (AKG/Precision/Presto/Plast/Polycab/MW or equivalent make as approved by the Deptt.) system, including connection as required complete as directed and specified by the Deptt. 1) With 2 x 1.5 sq.mm. cable in flat 19mm ISI marked casing 'n' capping system,

Wiring for drawing sub-main line with P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright up to 1100 volts (Finolex/RR Kabel/Nicco/Anchor or Equivalent Make as approved by the Deptt.) in surface flat ISI marked casing 'n' capping (AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) system including earth continuity. 1) With 2x2.5 sq.mm + earth continuity with 1x1.5 sq.mm. in flat 19mm ISI marked casing 'n' capping system.

2) With 2 x 4 sq.mm. + earth continuity with 1x2.5 sq.mm. cable in flat 19mm ISI marked 'n' capping system.

Wiring for drawing sub-main line with P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finlolex/RR Kabel/Nicco/Anchor or Equivalent make as approved by the Deptt.) including earth continuity in surface/recessed PVC 20mm. dia 2mm thick/heavy ISI marked IS:9537 PART-III rigid PVC conduit (Berlia/AKG/Precision/Presto Plast/Polycab/MW or equivalent make as approved by the Deptt.) wiring system. With 3 x 6 sq.mm + earth continuity with 2x4 sq.mm.cable in 25mm. dia 2mm thick/heavy rigid PVC IS:9537 Part -III conduit.

Wiring for 5 pin 6 amp plug with 1.5 sq.mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694:1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kabel/Nicco/Anchor or Equivalent make as approved by the Deptt.) including providing & fixing 5 pin 6 amp socket outlet (Anchor penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) make) and 6 amp flush type switch (Anchor penta/Gold medal/Kolor kany.Kom/Havells or equivalent make as approved by the Deptt.) make) earthing the 3rd pin of the socket as required on the switch board in surface/recessed ISI marked steel conduit pipe wiring system. When fitted on same board of light and fan.

Wiring for 5/6 pin 16 Amps power plug point with 4 sq.mm. P.V.C insulated single core unsheathed industrial (Multistrand) cable FR conforming to IS-694: 1990 with flexible bright annealed electrolytic copper conductor for voltage grade up to 1100 volts (Finolex/RR Kable/Nicco/Anchor or Equivalent make as approved by the Deptt.) in Surface/recessed conduit wiring system including earth continuity with 2.5 sq.mm cable to the 3rd pin of the socket as required complete with 20mm. dia. steel conduit (AKG or equivalent as approved by the Deptt).

Supplying and fixing of batten holder (Anchor Penta PC CHERRY/Gold medal/Kolor kany.kom/Havells or equivalent make as approved by the Deptt.) including connection as approved by the Deptt.) as required without Lamp.

Supplying and fixing of bulk head fitting suitable for CFL lamp complete with all accessories including 20 watts CFL lamp and connection as approved by the Deptt.) as required.

Supplying and fitting of 11/15 Watt CFL lamp in the existing batten holder/angle holder/decorative bracket/bulk head fitting/pendent holder etc.as specified and directed by the deptt.

Supplying with fitting and fixing sheet steel, phosphatised, powder painted single door surface mounting MCB DB incorporated with bas-bar, Neutral link, Earth bar and din rail etc fitted on wall with grounting nuts & bolts as reqd. complete with making necessary connection as approved, specified and directed by the deptt. 8 way SPN single door

Supplying with fitting and fixing single Pole 10 KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. 6 to 32A

Supplying with fitting and fixing TPN 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 63A

Supplying with fitting and fixing 4P 10KA 240/415V 50Hz MCB of the following capacity complete with making necessary connection as approved, specified and directed by the deptt. C Series (ABB, Schneider MG, legrand, Hager make) 125A

Supply, installation & testing of G.I earth station with perforated 40mm dia and 4.50 Metre long heady duty G.I. pipe with necessary 40mm dia. G.I fittings such as socket, Tee, elbow, nipple and 50mm x 40mm G.I reducing socket for funnel including locking arrangement 300mm x 300mm x 6mm hinged cover C.I earth plate complete with digging of earth pit, construction of brick chamber and plastering of both inner & outer surface of wall as specified and directed by the deptt.

Extra for using salt (5k and Charcoal (64K in pipe Earth Station pit to provide low impedance ground in location of high soil resistivity as and when required and specified by the deptt.

Supplying & laying of 8 SWG Copper. Earth from Earth Electrode (below G.L) to electrical switch gears or electrical machineries including making necessary connection as approved, specified and directed by the deptt.

Supplying including fitting fixing of following A.C Ceiling fan complete with all accessories like down rod, canopy etc. of following sweeps with making necessary connection as approved by the Deptt.) as required complete and as directed by the Department (Without regulator). 3) Premium model 1400mm Sweep. (ORIENT PSPO make) /Premium model 1400mm Sweep SS-390 Deco. Havells make).

Supplying including fitting fixing of following A.C Exhaust fan in the existing hole on the tube wall of following sweeps with making necessary connection as approved by the Deptt.) as required complete and as directed by the Department. High Speed 225mm sweep (ORIENT make), Trans Air 225mm sweep (Crompton make), Ventil Air DX 250mm sweep Louver type (Havells make).

Supplying fitting and fixing of ceiling fan regulator including connections etc.complete as required. Electronic type.

Supplying including installation, connection as approved by the Deptt., testing and commissioning of OPENWELL SUBMERSIBLE PUMP SET complete with submersible cable etc. as directed and specified by the deptt. 1.5 HP single Phase open well submersible monoblock water cooled pump set (Crompton Greaves/Aquatic/CRI/V-Guard make). 220v 50hz, 2900 rpm with control panel.

Payment to be made to APDCL authority for load security, meter security and service connection charge. (As per APDCL Tariff rate).

Amiya Khakhalary

SWRANG ENTERPRISE