REPAIR OF WALL PLASTER FLOORING TILING SEEPAGE JOINERY AND SANITARY AND OTHER ALLIED WORDS IN OTM ACCN IN MD ACCN OF 153 TA BN DOGRA 9 DIV PRO UNIT 522 ASC BN OLD LOCATION 16 RAJ RIF OLD LOCATION 409 FD AMBULANCE INT OFFICE 153 TA BN 9 ARTY

Amount

M&L injecting chemical emulsion for Post Constructional Anti-termite Treatment Along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron.

Treatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floors soil complete all as specified.

Treatment the soil under plinth protection at the rate of 5 litres of emultion per square meter of surfaces area.

At the point ofcontract of wood work by chemical emultion ( in oil or kerosene based solution) @ 0.5 litre / hole by drilling 6mm dia holes at a downward angle of 45 degree at 150 mm centre to centre and sealing the same

M& L 75mm thick PCC 1:3:6 Type C 2 (using 40 mm graded crushed stone aggregates) as in floor / plinth protection complete all as specified and directed.

M&L for 25mm thick PCC (1:2:4) type B1, (using 12.5mm graded stone aggregate) sub base as in floor complete all as specified.

M&L for providing cement concrete 1:2:4 Type B 1 (using 20 mm graded crushed stone aggregates) in lintels upto 1.5m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60cm in height, copings, kneelers, apex stones, bed plates, kerbs hold fast water troughs, filling in pressed steel door frame and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for providing cement concrete 1:3:6 Type C-1 (using 20 mm graded crushed stone aggregates) in cills, copings, kneelers, bed plates, kerbs, hold fast, fillings in pressed steel door frame and the like including weathering, slightly rounded or chamfered angles and throating, including necessary form work complete all as specified and directed.

M&L for providing precast RCC 1:2:4 type B-1 using 20mm graded stone aggrigate) as in cover slab chullah hoods, chajjas, water troughs, shelves or similar works set & jointed in CM 1:4 complete all as specified and directed.

M &L for Brickwork with fly ash bricks old size bricks straight or curved on plan exc 6m mean radius built in Cement mortar 1:6 complete all as specified and directed.

All as per Srl item No 10 here-in-before but except bricks

M&L for Brickwork with fly ash old size bricks, straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Supply only liquid water proofing compound complete all as specified and directed.

M&L for cutting chases, pinning in, in brick wall , making good to facings where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for concealed water tubing or concealed conduit wiring. etc. and making good, cutting exc 10 cm but n.exc 20cm girth complete all as specified and directed.

Material & labour for surface Preparation: The surface to receive the treatment shall be thoroughly free of laitance, scales, oil or any other loose material. It should be made free of any sharp objects. Cleaning of PCC shall be done with wire brushing to attain smooth levelled surface. Cracks shall be rectified, filled using dual shrinkage compensated Repair Mortar and dried for 72 hours before laying the liquid applied membrane. Grout: Providing Chemical injection treatment in the form of pressure grouting to the construction joint and cracked portion at 1m c/c by injecting cement slurry mixed with dual shrinkage compensated cementitious grout Injection grout additive, in the required consistency through the pre fixed PVC nozzles in the 18 mm dia holes, fixing of PVC nozzles with instant setting cement. Angle fillets/Coving: Providing and making of fillet, 50mm x 50mm on sharp corner of terrace with cement sand polymer mortar (add “multipurpose mortar”, 10% by weightofcement). First apply the bonding coat of Multi-Purpose Polymer 5-10% diluted in water and add to cement slurry. Apply the bonding slurry and apply the polymer mortar over the sharp edges. Note: Grouting will be done when and where ever required.

Treatment of pipe entry points: Preparing the inside surface of core and PVC /MS Pipe by roughening using suitable Sand paper to get better adhesion prior to packing works. Cleaning the surface by wire brushing followed water jet to remove any laitance or loose flaky particles. Packing the gap using free flowable non shrink cement polymer based grout up to the surface of the bore while the bonding agent is in tacky state. the periphery of PVC pipe should be sealed with Hybrid PU Sealant or dual shrinkage compensated Micro concrete Note: Will be done when and where ever required Application of Asian Paints two component Epoxy Primer (Resin & Hardener) on the cleaned surface for bonding of Polyurethane with the existing concrete surface. 33 % water dilution is recommended with the pure mixed primer. The primer mixing ratio will be 1:3(Resin:Hardner) Supplying, providing and applying waterproofing treatment to Podium area with single component highly elastomeric seamless cold applied modified PU coating complete as per manufacturer’s specifications and application methodology. The same coating shall be applied in two coats achieving a total thickness of 1mm. The coating shall have a dual combination of 280% elongation. Material coverage 1.2kg /sq.mt. (Note: Contractor is required to deposit 100% CA quantity to the Engr-in-Charge, within 15 days of acceptance of contract.

M&L for providing formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, exc 1.5m clear span cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc rough finished surfaces of concrete flat complete all as specified and directed.

S&F factory made glazed and skeleton shutters 35 mm thick 2nd class hardwood (SAL/ CHAMP / HOLLOCK) open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chemfered or rounded, fitted with cut and mitred beads for securing glass, etc.; sizes of members of shutters as specified in SSR Part-I, Section 8, clause 8.24 (a); for doors and fitted to chowkats complete all as specified and directed.

S&F 35 mm thick flush shutters, conforming to IS 2202 (Part-I) - 1999 solid core construction, with block board core and plywood face panels, commercial type on both sides, complete all as specified and directed.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) not exc. 1.5 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

Taking down chowkats or frames with shutters (without taking off shutter and builders hard ware fittings from frames) exc 1.5 sqm but not exc. 4 sqm each, complete all as specified and directed. Note :- Rate also incuding in this item for necessary cutting down / taking out hold fasts from the existing concrete / brick work and making good the disturbed surfaces with match existing surfaces.

S & F for Factory made double extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 125x65 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

S & F for Factory made single extruded WPC (Wood Polymer Composite) solid door/ window/ Ceosetory windows & other Frames/Chowkhat of size 85x45 mm comprising of virgin PVC polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/ wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) fabricated with miter joints after applying PVC solvent cement and screwed with full body threaded star headed SS screws having minimum frame density of 750 kg/ cum, screw withdrawal strength of 2200 N (Face) & 1100 N (Edge), minimum compressive strength of 58 N/mm2, modules of elasticity 900 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof,water/ moisture proof and fire retardant and fixed in position with MS hold fast/ lugs/SS dash fasteners of required dia and length complete as per direction of Engineer-in-Charge. (M.S. hold fast/ lugs or SS dash fasteners shall be paid for separately). ® Note: For WPC solid door/window frames,minus 5mm tolerance in dimension i.e.depth and width of profile shall be acceptable. Variation in profile dimensions on plus side shall be acceptable but no extra payment on this account shall be madecomplete all as specified & directed.

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door wire gauge shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S & F for 30mm thick Factory made single extruded WPC (Wood Polymer Composite) solid Moulded WPC door shutter of 30mm size comprising of virgin polymer of K value 58-60 (Suspension Grade), calcium carbonate and natural fibers (wood powder/ rice husk/wheat husk) and non toxic additives (maximum toxicity index of 12 for 100 gms) having minimum density of 650 kg/cum and screw withdrawal strength of 1800 N (Face) & 900 N edge),minimum compressive strength 50 N/mm2, modulus of elasticity 850 N/mm2 and resistance to spread of flame of Class A category with property of being termite/borer proof, water/moisture proof and fire retardant and fixing with stainless steel butt hinges of required size with necessary full body threaded star headed counter sunk S.S screws, all as per direction of Engineer-In-Charge.(Note: stainless steel butt hinges and necessary S S screws shall be paid separately)

S&F Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles & rails with suitable PVC sheet beading, and joined to gether with solvent cement, suppling & fixing in the frame at site as per specification & drawing on srl page No 174 of SSR Part-II complete all as specified and directed.

S&F Solid PVC Door frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S. Square tube, suppling & fixing in opening as per specification & drawing shown on page 178 of SSR Part-II complete all as specified and directed.

S&F PVC sheet wall panelling (sand wiched between the longitudinal grid in PVC sheet) 8mm thick, 10 inch wide and 10 feet long any pattern fixing at site with PVC beading / fillet and complete all as specified and directed by Engineer-in-Charge

M&L in repairs aluminium rubber beading for aluminium door, windows and ventilators as per required on ground complete all as specified and directed by Engineer-in-Charge

S&F powder coated (thickness of powder coating not less less than 50 micron) anodised aluminium frame for doors , windows, ventilators with one or more rebates with and including joining cleat for fixing etc complete all as specified and directed

S&F powder coated anodised aluminium door shutters, aluminium section weighing 0.55 kg/m with and including necessary joining aluminium cleats, aluminium glazing clips, ruber neoprene packing suitable size of aluminium, handles of size 150mm 2 Nos in each door, stainless steel hinges anodised aluminium snap beading for fixing glass panes / other filling material in panels, screws etc complete all as specified and directed. Note:- Glass panes / other filling materials in panels shall be measured and paid separately.

S&F powder coated anodised aluminium widnow and ventilator shutters, side hung type without sash bars aluminium section weighing 0.55 Kg/RM with and including necessary joining cleats, glazing, clips, rubber packing, anodised aluminium snap beading for fixing glass panes screws anodised aluminium fittings such as peg stays 150mm long (1 no) hinges type B-21 100mm long (2 No), extruded anodised aluminium alloy fabricated type handles of size 100mm 1 Nos complete all as specified and directed Note :- Glass panes in panes in panels shall be measured and paid separately.

S&F in repairs glass shelf assembly 60 cm long , 5.5 mm thick glass , CP guard and fixed to wooden plug with CP screws and cup washer as specified complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolts of extruded section, having shoot / dia of bolt not less than 12mm complete all as specified and directed.

S&F 200mm long aluminium anodised barrel tower bolts of extruded section, having shoot / dia of bolt not less than 12mm complete all as specified and directed.

S&F in repairs mild steel helical door spring of size 150mm fixed on flat iron fixed with screws or nut and bolts after welding the flat iron to MS angle iron / pressed steel chowkhats including welding etc, if necessary complete all as specified and directed.

S&F 300 mm long Brass, sliding door bolt with sand or die-cast brass hasp, staple (bolt type) and fixing bolt with rolled or drawn brass bolts and fixed. complete all as specified and directed.

S&F in repair 100mm size, 4 levers, brass mortice lock vertical type complete all as specified and directed.

S&F 300 mm long aluminium anodised, sliding door bolts, with haps staple (bolt type) and fixing clip of sheet cast or extruded section and fixing bolts and sliding bolts not less than 12mm dia of shoot / bolt of extruded section or cast aluminium alloy complete all as specified and directed.

S&F stainless steel butt hinges medium duty of 100 mm size, and fixed, complete all as specified and directed.

S&F 125mm size extruded aluminium alloy handles, fabricated type., anodised complete all as specified and directed.

S&F in repairs brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges, complete all as specified and directed.

S&F in repairs stainless steel fancy type curtain rod 25mm dia with two brackets of each door and window complete all as specified and directed.

S&F in repairs aluminiun (die cast) body door closer hydraulically regulated, designation No. 3, universal type, suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 Kg and fixed. complete all as specified and directed.

S&F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with tinned tacks, or galvanised wire staples including necessary beadings complete all as specified and directed.

S&F mild steel work as for Hand rails, half round or other stock section, nosing to steps in cluding embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.). including necessary riveting and / or welding and similar work conforming to Fe 290 gde E 165 complete all as specified and directed.

S&F mild steel work as for framed work such as grills gratings, etc., with ends of bars shouldered and/ or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed baluster; walk ways; railings; framed work of water tanks and similar work including necessary riveting and / or welding conforming to Fe 290 (Gde-E 165) complete all as specified and directed.

S&F 1.00 mm thick mild steel, plain, black sheet in wall cladding, steel gates and similar work, cut to size, holes punched; including, round headed screws, and fixed to wood or steel framing with plain 40mm lap joints with riveted or welded clout nails or rivets including bending or turning up, mitred angles, etc. as required. complete all as specified and directed.

M&L stone slab 50mm thick cement mortar 1:4 dressed true and square, in one length not less than 60 cm and n.exc 120cm in copings, window cills, chajjas, sunshades etc. punched dressed on exposed faces and self faced on the embedded unexposed beds and joints, exposed edges round or chamfered as directed, set jointed and pointed in mortar as in plinth protection complete all as specified and directed

M&L for mild steel TMT bars 10mm dia and over, cut length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia quality conforming to Fe- 415, Fe 500 or Fe-550 as in steel reinforcement for concrete complete all as specified and directed. Note :- Weight of binding wire shall not be considered for measurement and payment purpose.

All as per Srl item No 49 here-in-before but 6mm to 8mm dia bar

S&F rolled mild steel in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc including notching, drilling, fittings, riveting and / or welding or connecting with bolts and nuts (including rivets or bolts and nuts), providing fittings angle cleats, fish plates, gusset plates etc., also for wedging, plumbing, truing up and fixing conf to Fe-410-w (Gde-E -250) quality A complete all as specified and directed.

S&F rolled mild steel in framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fitting (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening conforming to Fe-290 (Gde E-165) complete all as specified and directed.

Taking down old existing water proofing treatment from top of RCC/arch slab including taking down of concrete padding or plaster and raking out joints of arch slab and hacking the top of RCC slab, cleaning with water and dispose off rubbish upto 200 meter complete all as specified and directed

M&L for providing average 50 mm thick PCC (1:2:4) type BO, (using 12.5mm graded crushed stone aggregates) as in roof padding finished fair and even without using extra cement complete all as specified and directed.

Supplied and fixed pre- painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50mm thick of any colour having tensile strength of 550 Mpa as in roof covering / cladding to wall, fixed with hot dip galvanised self dirilling and self tapping screws neoprene and EPDM washers complete all as specified, directed and as per manufacturer's instructions

M&L in repairs for perforated particle board tiles 12 mm thick for insulation and accoustic puposes, 60x60cm in size, fixed with Screws to timber frame work or with staples on snap grid in ceiling complete all as specified and directed.

M&L in repairs for 19 / 20 mm thick prelaminated particle board, ixterior grade, prelaminated one side with decorative choice lamination fixed with screw including applicant of adhesive or on joints and other side balancing white lamination, fixed with screw including application of adhesive on joints and Ist class hardwood beading on edge fixed in pelmet boxes or in narrow width n exc 15cm each, rebated or flat edged with screws to timber frame work and including taking down existing materials complete all as specified and directed.

M&L for 18-20 mm thick machine cut perfect black granite stone slab on vertical surface, skirting / dado, cooking platform, jams, pillars and other similar works set and jointed in neat cement slurry and pointed in coloured cement to match the colour / shade of granite including necessary rubbing and polishing laid over & including 10mm thick backing coat in CM 1:4 complete all as specified and directed.

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade / matrix of tiles and laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed".

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, in floors etc. set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade / matrix of tiles and laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed".

M & L Non skid coloured ceramic tiles 7 to 8 mm thick (square / rectangular), area of each tiles exceeding 0.18 sqm but not exceeding 0.38 sqm, as on skirting, dados, risers to steps etc . set & jointed in neat cement slurry and pointed in white or coloured cement to match the shade / matrix of tiles and laid over and including 10mm thick screed bed in CM 1:4 complete all as specified and directed".

M&L for Glazed ceramic coloured tiles of size 350mmx 250mmx7 mm / 450mm x 350mm x 7mm on vertical surface such as on skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles and over including rendering 10mm thick in cement mortar (1:4) complete all as specified and and directed

M&L for 16-18 mm thick machine cut mirror polished Granite stone slab PERFECT BLACK table rubbed polished and round edges as in cooking plateform, steps and window cills and like over and including 10mm thick scread bed in CM (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade / colour / matrix of granite complete all as specified and directed.

M&L 40mm thick brick tiles are bedded in cement mortar 1:6 or line mortar 1:3, 15mm thick joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement on cement concrete complete all as specified and directed

M&L in repairs for 20-25 mm thick machine cut kota stone slabs of size 540 mm x 540 to 560mmx 560mm in floors, set and jointed in neat cement slurry and pointed in coloured cement to match the shade / matrix of existing surface laid over and including 15mm thick screed bed in CM 1:6 complete all as specified and directed.

M&L in repairs for 20-25 mm thick machine cut kota stone slabs of size 540 mm x 540 to 560mmx 560mm as on vertical surfaces such as skirting dados, step risers etc. set and jointed in neat cement slurry and pointed in coloured cement to match the shade / matrix of existing surface laid over and including 10mm thick screed bed in CM 1:4 complete all as specified and directed.

Dismantling of floor, hearth or wall tiles / terrazzo including cement mortar bedding (but not backing),removal servicable tiles to store and rubbish off the premises, complete all as specified and directed.

M&L for rendering 15 mm thick in cement mortar 1:6 on fair faces of brick work or concrete vertical surfaces, finished even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 10 mm thick using ready mix bags in cement mortar 1:4 on roof surfaces, finished even and smooth without using extra cement with using water proofing compound @ 3% complete all as specified and directed. Note:- water proofing compound will be measured and paid seperately. Note :- Contractor is required todeposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M & L for applying 15mm thick rendering unsing ready mix plaster bags in CM 1:4 on brick / concrete surfaces of external walls finished even and fiar, using water proofing compound @3% by weight of cement of as per manufacturer instructions, complete all as specified an directed. Note:-Water proofing compound shall be measured and paid sepratly Note Contractor is required to deposit ready mix bags for 100% CA quantity to the Engr-in-Charge within 15 days of acceptance of contract.

M&L for rendering 5 mm thick in cement mortar 1:3 on ceiling of brick or concrete surfaces, finished even and smooth without using extra cement complete all as specified and directed.

Taking down cement plaster on brick or stone walls, etc. including raking out joints, hacking for key, scrubbing down with water, etc and including removal of debris and rubbish from the site complete all as specified and directed.

M&L for three coats of white wash on newly plastered or unplastered surfaces of ceiling including preparation of surface complete all as specified and directed.

M&L for preparing of old decorated surfaces of ceiling ( plastered or un plastered ) including cornics etc and applying one coat of white wash complete all as specified and directed

M&L for preparation of new surfaces and applying one coat of primer on using roller complete all as specified and direcrted.

Material & labour for applying 3mm thick wall care putty making smooth surface complete all as specified and directed

M&L preparation of old decorated surfaces after complete removal of existing treatment by mechanical complete all as specified and directed .

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and directed.

S&F in repairs for 4mm thick sheet glass, ordinary quality and glazing with oil putty or glazing pins in square n exc 0.5 sq. m in each pane complete all as specified and directed.

S&F 10mm thick toughned glass as per in hinged doors, partitions automatic doors and similar work including cutting to shape, drilling holes requied complete all as specified and directed

Taking up or down GI water tubing 15mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Taking up or down GI water tubing 20mm bore and connection including cleaning serviceable pipes for refixing and unserviceable removal from the site complete all as secified and directed

Supplying and laying of CPVC 16mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ ceiling or laying or laying in floors complete all as specified and directed

Supplying and laying of CPVC 20mm outer dia pipes SDR 11 & Plain CPVC SDR 11, with all fittings and fixed on walls/ ceiling or laying or laying in floors complete all as specified and directed

Dismantling of old water tank exc 250 Ltrs & n.exc 500 Ltrs capacity and Supplied, hoisted and fixed in position triple layer white colour rotational moulded polyethylene water storage tanks IS : 12701 - 1996 marked (cylindrical vertical with closed top) of 500 Ltrs capacity with and including 20mm bore dia Ball valve high pressure of PTMT with epoxy aluminium rod & high density plastic ball screwed for iron pipe and fixed. (Minimum weight 210 gms) complete all as specified and directed.

S&F in repairs bib taps, cast copper alloy chromium plated with crutch or butterfly handle, sc-rewed down, screwed for iron pipe or for brass ferrule of 15 mm bore dia and fixed complete all as specified and directed.

S&F in repairs stop valves, 15mm bore dia, cast copper alloy, chromium plated screwed down, high pressure with crutch or butter fly handle, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supplied and fixed in repairs brass chromium plated wall mixer for mixing Hot & Cold water high pressure, screwed down for 15mm bore iron pipe fixed in repair all as specified and directed. (Make:- sona or equivelent as approved by GE).

Supply and fixed stop valves, 15mm bore dia, cast copper alloy, CP with long shank and cup(concealed type) screwd down,high pressure with crutch or butter fly handle,screwed down both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supply and fixed in repairs gun metal globe valves, 15mm dia, with iron wheel head ,screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

Supply and fixed in repairs gun metal globe or gate valves, 20mm bore dia, with iron wheel head, screwed both ends for iron pipes or for unions and fixed in pipe complete all as specified and directed.

S&F in repair ball brass valves, high pressure, with polythene float and flynut complete, screwed for iron pipe or brass ferrule and of 20 mm bore and fixed complete all as specified and directed.

Supplied and fixed in repairs CP soap dish as per sample kept in the office of Engineer-in-Charge complete all as specified and directed.

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified and directed.

Supplied and fixed in repairs MS CP grating 125 mm dia over floor / Nahni traps complete all as specified and directed.

Supplied and fixed in repairs 110mm bore PVC (SWR) pipes single socketed in any length with rubber ring joint, fixed to wall complete all as specified and directed.

Supplied and fixed in repairs 75 mm bore PVC(SWR) pipes single socketed in any length with rubber ring joint fixed to wall complete all as specified and directed.

Supplied and fixed PVC (SWR) bends 110 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) bends 75 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) 75 mm dia branch piece,single(single 'Y') equal or unequal complete all as specified and directed directed

Supplied and fixed PVC (SWR) vent Cowl 110 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) vent Cowl 75 mm bore complete all as specified and directed

Supplied and fixed PVC (SWR) floor trap 110 mm bore including jointing to waste pipe with cement solvent fixed in cement concrete complete all as specified and directed

S&F PVC waste pipes of 32mm bore suitable for wash hand basin / sinks complete all as specified and directed

S&F 110 PVC (SWR) reducer complete all as specified and directed

S&F 110 PVC (SWR) couplers complete all as specified and directed

S&F 75 PVC (SWR) couplers complete all as specified and directed

M&L for dubbing out average 20mm thick on irregular faces of wall and ceiling CM 1:3 complete all as specified and directed

S&F stack clamps out of 50mm by 5mm flat iron and 16mm dia round iron stays including bolts and nuts and securing ends of stays to wall or roof complete all as specified and directed

Supplied and fixed in repairs PVC (SWR) gully trap 110 mm bore setting and jointing with solvent cement complete all as specified and directed

Supplied and fixed in repairs PVC (SWR) 'S' trap 110 mm bore all as specified and directed

Supplied and fixed in repairs vitreous china WHB, white, flat back size 550x400mm including cutting for and pinning in ends of bracket or erecting stand with and including angle iron brackets, duly painted with two coats of synthetic enamel paint over one coat red oxide zinc chrome primer and providing cast copper alloy capastan head C.P brass pillar tap fency type 01 No 15mm bore, CP brass waste coupling 32mm dia, PVC waste pipe 32mm dia and PVC connection 450mm long high pressure with PTMT nut complete all as specified & directed.

Supply and fixing in repairs vitreous china squatting pan, Orissa' pattern, size 580 x 440mm white, with integral foot rests with and including cast iron 'P' or 'S' trap and setting the trap and pan in and including PCC 1:4:8, type D-2 minimum 150mm thick all round and finished just below level of rim of pan to receive the floor finishing, making all connections complete all as specified and directed.

S&F in repair vitreous china wash down water closet pan (padestal pattern), white with 'P' or 'S' trap (excluding flushing cistern and flush pipe) including connection to drain or out going pipe and to flushing pipe, antisyphonage pipe etc complete all as specified and directed

Supply and fixing in repairs PVC low level flushing cistern of 10 Ltr capacity syphonic action type with inlet ball valve, float and handle including PVC brackets for mounting of cistern complete all as specified and directed.

Supplied and fixed in repairs 125 mm size brass chormium plated shower rose including fixing to steel pipe or union complete all as specified and directed

S&Fin repairs sinks with drainage board made of stainless steel 1mm thick sheet for kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 915mm x 460mm bowl size 410mm x 330mm x 160mm complete all as specified and directed.

Supplied and fixed in repairs vitreous chinaware EWC padestal type closet with white seat & cover with flat bottom with hinging device and flushing cistern complete all as specified and directed.

M&L for concrete bed in PCC 1:4:8 type D-2 (using 40mm graded crushed stone aggregates) to drain pipe including packing under and haunching against the sides of pipes after they are laid and tested for 150 mm bore of pipe complete all as specified and directed.

M&L for SGSW 'grade 'A' drain pipe 150 mm internal dia laid in trenches , jointed and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains,( internal dia of pipe 100 mm ) making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-I smooth finished, and reforming benching as required complete all as specified and directed.

Demolition and breaking up drain pipes ( SGSW, AC or reinforced concrete ) set in cement mortar for 150 mm internal dia of pipe complete all as specified and directed.

Removal of blockage of chocked sewage line up to 150 mm dia between two man holes (any length beyween two consecutive man holes) including flushing of sewage pipe line and removal refixing of existing main hole cover complete all as specified and directed.

Demolition of brick work or rubbled stone masonry including all quoins arches , pillars etc built in cement mortar and including removal from the site complete all as specified and directed.

Demolition of cement concrete in ground floors and paving n.exc 15cm thickness(below or above ground level) and including removal of debris & rubbish from the site complete all as specified and directed. Note : Stone slabs / tiles and hard core of any description shall not be measured & paid under this item.

Dismantling of stone slab and tiles of any description or thickness laid bedded and pointed in any mortar as in floors, aprons, skirting / dados etc complete and removal of dismatled / demolished material from the site complete all as specified and directed.

Dismantling AC sheet corrugated or semi corrugated sheet of any description as in roof and including removal from the site complete all as specified and directed.

Dismantling of wall or ceiling board / panelling (fiber,pulp,insulation etc) any thickness including cover fillets and removal from the site complete all as specified and directed.

Dismantling of brick tiles or terracing tiles single layer on roof complete all as specified and directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specified provide (reinforcement cut to faciliate demolition) complete all as specified and directed.

S&F in repairs 8mm dia, brass chromium plated health faucet with 1 meter long flexible hose and wall hook complete all as specified and directed Make - Jaquar, Parko, Gem or equivalent

S&F in repair CP toilet paper holder complete Make : Jaquar Parko, Gem, Marc or equivalent

S&F in repairs aluminium anodised barrel tower bolts 150mm long, of extruded section

S&F in repairs aluminium sliding door bolt 300 long bolt type with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate all as specified & directed

M&L for preparation of new plaster surface and applying Two coat of OBD using roller for painting complete all as specified and directed

M&L for applying two coat of OBD using roller for painting on old surfaces complete all as specified and directed

Material & Labour for applying Two coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces using roller for painting

S & F in repairs PVC heavy duty waste pipes of 32mm bore suitable for wash hand basins/sinks complete all as specified & directed

S&F in repairs 4 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 sq. m in each pane

S&F in repairs stainless steel wire cloth, 0.56mm nominal dia of wire and average width of aperture 1.18mm

M&L for preparation of old painted wooden surfaces of any description not otherwise described over 10 cm in width or girth and applying one coat of white / tinted synthetic enamel paint complete all as specified and directed

S&F fancy type brass CP hot and cold wash hand basin mixer 15mm bore screwed down high pressure with long screwed shanks and fly nuts, screwed to iron piep (Make - Jaquar Cat Part- No SOL-6167B) complete all as specified and directed

M/S AMAR ELEKTRO CENTRE

Gupta Automobiles