SPECIAL REPAIR BLDG NO P105 P107 P113 AND P115 AT JALIPA MIL STN UNDER GE army BARMER

Amount

Taking down cement plaster on stone walls including raking out joints hacking for key, scrubbing down with water etc.

M&L for Plastering 15mm thick in CM (1:4) on stone wall surface(external wall surface) finishing the surface even & smooth with mixing of water proofing compund as per manufacture instructions. Note: Water proofing compound shall be measured and paid sepeartely as supply only rate.

M&L Plastering 15 mm thick in CM (1:6) on stone wall surface finished even and smooth without using extra cement on internal wall.

M&L for plastering 5mm thick in C:M 1: 3 in (concreate surface)ceiling finished even and smooth without using extra cement.

M & L for Preparation of new plastered surfaces of wall and applying two coats of cement base paint .

M&L for Prepration of new plastered surface of ceiling and applying three coat of white wash in ceiling

M & L for preparation newly plastered surfaces on wall & applying a layer of wall care putty 3 mm thick(averaging) on wall surfaces including cornices etc for proper levelling of plaster and two coat of oil bond distemper over a coat of primer complete all as specifed and directed.

M&L 25 mm thick cement concrete (1:2:4) type B-0 (12.5 mm graded stone aggregate) as in sub base of floors. complete all as specified.

M&L for 75mm thick cement concrete 1:3:6 type C2 using 40mm graded stone aggregate as in floors/ plinth protection etc finished even and fair complete all as directed

Taking down unserviceable chowkhat or frame with shutter (without taking off shutter from the frames) exc 1.5 sq.m but n. exc 4 Sqm each .

S & F Pressed steel frames of size 165X 60mm and 1.25 mm thick for doors with double or single rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed.

S & F Pressed steel frames of size 105X 60mm and 1.25 mm thick for doors with double rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified and directed

M&L 35 mm thick Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

S&F factory made 35mm thick 2nd class HW glazed and skelton shutter and open rebated and prepared to receive glass, gauge etc (without sash bars), edges or framing plain chamfered or rounded fitted with cut and mitred beads for securing glass etc size of members of shutter as specified in SSR Part I section 8 clause 8.24 (a) supplied and fixed to chowkats.

S & F in repair of 300 mm long brass, ordinary rat tail rod pattern springs including roller and roller plate complete

S&F Butt hinges 100 mm size, medium weight, cold rolled mild steel etc complete.

M&L for preparation of new wooden surfaces of any description over 10cm width or girth & priming coat with pink primer and applying two coat of sythentic enamel paint all specified.

M&L for preparation of old wooden surfaces of any description over 10cm width and applying one coat of sythentic enamel paint all specified.

Taking down chowkhat or frame with shutter (without taking off shutter from the frames) n. exc 1.5 Sqm each

S& F solid PVC door frame of size 50x47mm made out of 5mm plain colour PVC sheet reinforsed with MS square tube supplying and fixing in opening as per specification & drawing

S/F factory made solid panel PVC door shutter 30mm thick (Style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strips of 20mm width stuck inside with solvent cement for tiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/sealed the stiles and rails with suitable PVC Sheet beading and jointed together with solvent cement supplying & fixing in the frame at site all as specification and drawing .

S&F barrel tower bolt 150mm long aluminium anodised extruded section

S&F aluminium anodised handle 150mm long cast type

S&F butt hinge size 100mm extruded aluminium alloy with galvanised mild steel hinges pin,anodised and fixed type B 21

S & F 250mm long Aluminium alloy, anodised,sliding door bolt with hasp,staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed

M & L for rendering or plastering15mm thick in Cement mortor 1:3 for work in (Chajja and Facia downward/upward face ) isolated widths or in widths not forming part of general plastering such as in bands, sunk panels, cornices, skirtings, drip moulds and similar work including cutting to edges, all mitres and stopped ends including necessary scafolding.

Demolition of brick work or cement concrete block or stone/boulder masonry built in cement mortar including all quoins arches pillars etc & removing unserviceable material in low lying area complete all as specified and as directed.

M&L for square rubble walling Jodhpur type regular course well bonded bedded and solidly hearted built in cement mortar (1:6) all as specified and directed

Taking up or down steel tubing and connections (a) 15 mm bore pipe

All as per Srl Item no 29 above but 25mm bore pipe

S&F GI tubing medium grade including all fittings fixed to walls and ceilings or laid in floors of following sizes :- (a) 15 mm bore pipe

All as per Srl Item no 31 above but 25mm bore pipe

Relaying /Re - fixing Old water tubing 15mm dia (bore) and connections in new or old position after cleaning both inner and outer surfaces of pipes including provision of New GI fittings (as ordered), complete all as specified and as directed.

Relaying /Re - fixing Old water tubing 25 mm dia (bore) and connections in new or old position after cleaning both inner and outer surfaces of pipes including provision of New GI fittings (as ordered), complete all as specified and as directed.

Dismantling and taking down water storage tanks of 1000 Ltr capaciaty and S&F 1000 ltrs capacity rotatonal moulded polyethylene white three layer water storage tanks (cylindrical vertical with closed top) hoisted and fixed in position including S&F of ball brass valve high pressure of 25mm dia etc .

S&F in repair stop valve cast copper alloy screwed down high pressure with crutch or butterfly handle, screwed both ends for iron pipe of 25mm bore.

S&F in repairs bib tap, 15mm bore, fancy type, chromium placed screwed down screwed for iron pipe or for brass ferrule complete.

S&F in repair vitreous China wash hand basin of size 300x450mm with CI bracket and comprising of the following :- (a) Waste fitting 32mm dia brass chromium plated with long screwed shanks and fly nut flange end bedded in red lead cement and other end fixed. (b) Pillar tap cast copper alloy with capstan head chromium plated, screwed down, high pressure with or without leltered hot or cold with long screwed shank and fly nut. (c) PVC waste pipe 32mm dia 600mm long. (d) PVC Connection 15mm size with PTMT nuts of length 450mm long.

S&F CP fancy type stop valves/Angle valves screwed down high pressure, with crutch butterfly handle screwed both ends for iron pipe or for unions and fixed to 15mm bore dia pipe. complete all as specified.

S&F fixing in repair 10 Ltrs PVC valveless, syphonic action type, flushing cistern, low level, white, with inlet, ball valve, float and handle including brackets and connection to pipes and fixing of lever.

S&F in repair PVC connection 15mm size 450mm long with brass fly nuts and washers on both ends complete.

S &F chromium plated shower roses with or without swivel joints, 125mm in size including fixing to steel pipe or union complete all as specified and as directed.

S & F in repairs for Cast iron nahani trap 75 mm dia, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4)

S/F sheet glass shelf assembly consisting of 5.5 thick sheet glass self 12cm wide with chromium plated bracket guard and railing 60cm wide, complete all as specified and as directed.

S&F in repairs pedestal pattern one piece white EWC, seat cover with internal fittings, PVC connection etc and connecting to drain flush pipe etc all complete all as specified and directed .

S&Fixed in repair Water closet (Squatt pattern) vitreous China squatting pan, ‘Orissa’ pattern, size 580 x 440 mm white, with integral foot rests (excluding flushing cistern and flush pipe)complete including provision of lime/cement concrete bedding all as specified and directed .

Demolation of wall/ floor tiling of any description including back coat, removing the dabries & rubbish from the premises

M&L Cement concrete 1:2:4 type B0 using 12.5mm graded aggregate stone aggregate 25 mm thick in sub bases of floor/paving.

M & L for coloured glazed cermic tiles size 300x450x7 mm thick on vertical surface of wall over and including 10mm thick backing coat in CM 1:4 set and jointed in neat cement slurry and pointed in white cement/coloured cement to match the tiles.

M&L coloured non skid ceramic tiles of size 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick cement backing coat in CM 1:6 complete all as specified and as directed

M&L coloured non skid ceramic tiles of size 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm in etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick (CM 1:4) cement backing coat in complete all as specified and as directed as in skirting.

M&L coloured non skid ceramic tiles of size 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 20mm thick cement screed bedding layer in CM 1:6 complete all as specified and as directed

M&L coloured non skid ceramic tiles of size 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in SKIRTINGS etc set and jointed in neat cement slurry and pointed in white or coloured cement to match, including 10mm thick cement backing coat in CM 1:3 complete all as specified and as directed

Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; not exceeding 200mm thick horizontal or sloping, finished rough complete all asspecified and directed .

Formwork to edges of concrete flats,treads,breaks in floors,window cills,concrete railings,openings in concrete walls,floors abd roofs n exc 20 cm wide and sides of RCC/PCC bands in walls,horizontal or sloping and similar work exc 10cm but nexc 20cm wide rough finished surfaces complete all as specified & directed .

M&L TMT mild steel bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed .

M&L TMT mild steel bars 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified & directed .

M&L TMT mild steel bars 8mm dia and over as in striups, spacers & binders, cut to length, bend to shape required and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed .

M&L RCC type B1 (1:2:4) using 20 mm graded aggregate in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves.

M & L for RCC type B1 1:2:4 (20mm graded stone aggregate) as in lintles, beams etc all as specified.

M&L rendering 10mm thick in CM 1:3 on fair faces of brick or concrete surfaces and complete all with water proofing compound as specifeid. The plaster shall be provided when the concrete is green.

M&L Machine cut Kota stone slab flooring (In one piece only) 18-20mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing and rounding to edges of Kota stone shall be rounded including 15mm thick back coating layer in CM 1:6 complete all as specified.

M&L Machine cut Kota stone in verticale surface (In one piece only) 18-20mm thick over cement skerting laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing and rounding to edges of Kota stone shall be rounded including 15mm thick screed bedding layer in CM 1:4 complete all as specified.

Demolition of cement concrete of any description and in any position including removing the debries & rubbish to a distance n.exc 100 mtr as directed.

Demolition of reinforced cement concrete of any description and in any position including removing the debries & rubbish to a distance n.exc 100 mtr as directed.

M & L for applying neat cement slurry with 3 kg of cement per sqm & mixing of liquid water proofing compound as per manufacturer instructions on surface of roof slab (Note: liquid water proofing compund shall be measured and paid separately)

M/L for providing 40mm average thick cement concrete 1:2:4 type B-0 (12.5mm graded agg) with mixing of liquid waterproofing compound as per manufacturer instructions and finished the cement concrete surface even & smooth without using extra cement (Note: liquid water proofing compund shall be measured and paid separately)

M&L for screed bed/plastering 10mm thick in CM (1:3) on concrete surfaces (old or new)of roof with mixing of liquid waterproofing compound as per manufacturer instructions and finished the surface even and smooth without using extra cement (Note: liquid water proofing compund shall be measured and paid separately)

M&L for Priming the surface of concrete/plaster with bituminous primer 0.40 litre per sqm.

M&L for laying of APP based polymeric membren minimum weight 3Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (wt not less than 150gm/sqm) laid on primed surface by torched application complete etc all as per manufacturer instructions.

Supply only liquid water proofing compound

M&L two coat of aiuminium paints on roof surface etc complete.

M & L for Providing cement concrete(1:2:4) type Bo(using 12.5 mm graded stone agg) for coved fillets of radius 75mm provided at junction of roof and parapet/vertical surfaces, pedding concrte to achive slope as required & making plateform for water tank on roof slab etc.

M & L for MS props erecting for temporary supports to the structural members like beams, slabs etc. to relieve the load on the members during breaking of damaged concrete, removal guniting, excavation or any dismantling work as per the instruction of engineer in-charge. These supports shall be provided either in the form of props or trestles fabricated using structural steel as per the site requirements.

M & L for Chipping of slab/columns/beams/chajjas/parapet/roof projection/balcony/staircase and removing loose mortar with chisel hammer without much impact on concrete surface, clean the surface by sand blasting the surface using river sand with minimum of 6 kg pressure at the nozzle or air blow by electric pressure blower by mechanical compressor, cleaning the exposed reinforcement with wire brushes etc and disposal of debris foe all lead and lifts, all complete all as specified and directed.

M & L for Cleaning & applying rust remover (CICO Clean-o rust) in two coats over rusted reinforcement surface and providing anti corrosive coating with two component epoxy based zinc rich primer/Rust passivation Inhibitor coat at the rate of 6-8 sq. mtr/ltr not less than 50 microns dft with CICO ZINCILATE-500 or equivalent to reinforcement surface as per manufacturer’s instructions including all machinery, tools tackles and clearing of debris. Make: CICO clean-O-rust, CICO ZINCILATE-500 or equivalent in Fosroc/Dr Fixit/ACC/L&T/STP

M & L for Hard drawn steel wire fabric n exc 4Kg/Sqm cut to lengths, bent to shape required and tying with and including mild steel wire (annealed) not less than 0.9mm in dia supplied and fixed in reinforcement.

S & F of new steel or rebars by drilling holes with 10 mm to 20mm dia and 100 to 200mm deep as per IS code of 10D formula and filling the holes after inserting of reinforcement dia 8 to 16mm for anchoring at ends/shear connector and filled the holes with one or two component styrene free vinylester resin anchor or two components, styrene & cement free epoxy- acrylate fixing and anchoring compound ( having the technical parameters mentioned in material specifications) using standard sealant applicator gun after drilling holes of required diameter at required locations, for holding / fixing / placing in position the steel mesh reinforcement at desired level/ stretching. (Note : Steel/reinforcement shall be paid and measured separately) . Make: CICO RESIFIX-G or equivalent in Fosroc lokfix/Hilti and Master builder (BASF)

M&L for applying to the damaged concrete portion of slab/columns/beams/chajjas/parapet /roof projection/balcony/staircase with single component, fiber reinforced, dual shrinkage- compensated thixotropic, cementitious ptch repair mortar CICO Repocem PM (having the technical parameters mentioned in material specifications ) capable of applying up to 20- 25mm thick in double layer initially by hand and finishing with troweled carefully compacting the same around the rebar and finishing to bring it in line with existing concrete surface with an average specified thickness and Equivalent of Fosroc Renderoc/STP/BAS

M & L for applying bond coat on the prepared old surface of concrete/masonry to receive new polymer mortar/polymer modified mortar or micro concrete with two coats of CICO-Latex SBR or equivalent in Fosroc /STP as per manufacturer specifications. Laying of reinstatement polymer mortar or micro concrete shall be completed within the overlay time of bonding coat. This bond coat act as bonding agent between old and new concrete. MAKE: CICO LATEX SBR or equivalent in Fosroc/STP/BASF

Taking down unserviceable glazed / flys proofing steel ventilators, windows and doors any size etc complete.

Dismantiling of cast iron pipe including fitting jointed in ,cement joint 100 mm bore.etc.

S&F 100 mm bore cast iron soil waste and vent pipe sand costed in any length with or without ears with cement joints fixed to wall:-

S&F in repair Aluminium anodised Tubular towel rail 20mm dia, D type, 60cm long between flanges

S&F curtain rails,anodised aluminium alloy, chromium plated with fixing brackets, stops, rollers etc.

S&F 110mm dia PVC(SWR)pipes single socketed, in any length with rubber ring joints,fixed to walls, fixed in repairs.

M & L for preparation old plastered surfaces on wall & applying a layer of wall care putty on wall surfaces including cornices etc for proper levelling of plaster and two coat of oil bond distemper over a coat of primer complete all as specifed and directed.

M&L for complete removal of existing treatement of walls and prepare the wall surface with wall care putty and than applying a coat of primer and over it applying two coat of Acrylic distemper oil emulsion white or tinted.

M & L for preparation old plastered surfaces on wall & applying two coats of cement base paint complete all as specifed and directed ..

S&F stainless steel [Grade 304] modular kitchen baskets of different sizes and pattern to suitable for kitchen cabinets complete all as specified and directed. Make: Universal / Evershine / Nirali / Gilma / Faber or equivalent as approved by GE.

S&F 12mm thick MDF pre laminated board as in kitchen cabinets of any size provided with shelves, partitions, glass shutters with stainless steel cabinet hinges (02 Nos for each shutter) , movino drawer channel (02 Nos for each shutter) handles (01 No for each shutter) , fancy knob (01 No for each shutter) including magnetic lock and other necessary fittings as required, shape / pattern as approved complete all as specified and directed.

S&F 9.75mm thick MDF pre laminated board as in cup boards of any size provided with shelves, partitions complete all as specified and directed.

M&L 18-20 mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, win?dow-cills, cooking plat?forms and like in cement mortar (1:4) including point?ing in white cement (1:2) us?ing marble dust with admix?ture of pigment to match with shade of granite

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 sq m on plan and n exc 1.5 m in depth and getting out in Hard dense soil.

M&L 200mm Sail-glazed stoneware drain pipes laid in trenches and jointed as specified

M&L concrete bed to drain pipes including forming cradles in cement concrete 1:4:8 type D-2 complete all as specified and directed.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm.

Removing excavated soil n exc. 50m & depositing where directed at a level n exc. 1.5 m above the starting point

Taking down copper/aluminium point wiring (light, fan, socket or power) complete, including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fitting etc. removing materials to store for keeping in safe custody or for taking credit (credit for above items should be made as per conditions separately) and making good disturbed surfaces of walls, floors, etc

Taking down unserviceable main switch/DB, Teak wood boards etc

Taking down submain wiring of any size complete all as directed.

M&L for point wiring in concealed with PVC insulated, unsheathed, single core multistandard copper conductor cable( FRLS) of size 1.5 Sqmm, 1100 volts grade including 1.5 Sqmm PVC insulated, unsheathed, copper conductor cable for earth continuity wire to be drawn through in and including PVC conduit medium grade ISI marked with its acessories including necessary pressed steel terminal boxes flushed in wall and 3 mm thick ISI marked laminated sheet cover and SS screws with cup washers for fixing switches, sockets, fan regulators etc. including all necessary wall cutting chases and making good disturbed surfaces in cement mortar 1:3 for one light /CB point controlled by one switch, complete all as specified and as directed.

All as per item No 106 above but for one ceiling fan point controlled by one switch.

All as per item No 106 above but for one exhaust fan point controlled by one switch.

All as per item No 106 above but for one 3/2 Pin 5 Amp socket out let point on the independent board.

All as per item No 106 above but for one socket outlet 3/2 pin, 5 Amp, point on the same board with other switches.

All as per item no 106 here-in-before but with cable 2.5 sqmm including 2.5 sqmm cable as earth wire for 15/16 amp socket point.

All as per item no 106 here-in-before but with cable 4 sqmm including 4 sqmm cable as earth wire for 15/16 amp socket point.

Supply and fix single pole and neutral enclosures with a two pin and earth plug and socket complete with one double pole MCB 10 A ,240 V complete all as specified and as directed.

Supply and fix switch piano flush type single pole one way 5 Amps complete all as specified and as directed

Supply and fix socket outlet 2in1, 3pin,5A complete all as specified and as directed.

Supply and fix socket outlet 2in1, 3pin,6/16 A complete all as specified and as directed.

Supply and fix switch piano flush type single pole one way 15 Amps complete all as specified and as directed.

Supply and fix ceiling rose surface bakelite 65x50 mm two to three terminals.

Supply and fix step type electronic fan regulator flush type, 230 volt, AC complete.

S&F Supply and fixing single pole 06 to 32 A rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) in the MCB DB complete with connection testing andcommissioning, complete all as specified and as directed

All as per Item No 120 but SPN 32 A rating complete all as specified and as directed

All as per Item No 120 but TPN 63 A rating complete all as specified and as directed

S&F sheet metal enclosure, (for DB's when MCBs to be used), flushed in wall single pole and neutral Double door, 8 way, 240 Volts with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed.

S&F MCB, DB double door type, made out of CRCA mild steel sheet flushed in wall, TPN 4 way with 200 Amps rated bus bar , 415 volts IP-43, with PVC MCB blanking plates, stove enamelled, dust and vermin proof suitable for incorporation of MCB's and isolators etc complete all as specified and as directed.

Taking down ceiling fan in serviceable condition and refixing the same location after oiling/greasing as required complete all as specified and as directed

M&L sub main wiring concealed type with two runs of single core, PVC insulated, unsheathed multi standard copper conductor cable of size 6 Sqmm, 1100 volts grade (FRLS) and one run o f 6 Sqmm PVC insulated multi stranded copper conductor for earth continuity conductor drawn through and including suitable size ISI marked rigid PVC conduit with all necessary accessories such as bends, tees, junction boxes, elbows complete all as specified and as directed. (Note :- Two runs of 6 Sqmm cable, one run of 6 Sqmm continuity earth wire and one run of PVC conduit with all necessary accessories will be measured as one length).

Taking down and refixing LED tube light fitting retrived from old existing location, in serviceable condition and connectiong up with twin core twisted flexible copper conductor cable with suitable size complete all as specified and as directed

S & F LED batten suitble for indoor application 20 W, 4' length , wall mounted with aluminium housing, end cap made of ABS plastic of white colour finish and high efficiency translucence (HET) diffuser and integral electronic driver including two point surface mounting on wall/ ceiling and connecting up with twin core twisted flexible copper conductor cable of suitable size complete all as specified and as directed

LED light fitting 1X9 W bulkhead luminaires with lamp holders etc complete with all aceessories including connecting up with twin core twisted flexible copper conductor cable complete all as specified and as directed by Engr-in Charge.

S & F in replacement LED 25 Watt street light fitting for bldg secutiry complete with light grade GI brackets, Nuts, bolts with omplete with all accessories internaly pre wired and including connecting up with twin core twisted flexible copper conductor cable with suitable for wall mounting as specified and directed by Engineer in charge Make - Crompton/ Havells/ Philips/Bajaj.

Supply and replace GI pipe bracket for street light fittings made out of 40 mm dia GI pipe light grade 1.5 mtr long bent to required angle/ shape with and including necessary clamps, nuts, bolts, & washers of suitable size all as directed by Engineer - in - Charge

M & L lamp holder (Angular) PVC/poly carbonate type with back plate suitable for batten fittings

Supply & fix LED lamp 10 W , min lumen output 950 lumens at 6500 K CCT for batten holders complete all as specified and as directed.

M & L earthing complete with GI earth plate Electrode 60 cm x 60 cm x 6 mm thick burried directly in ground (earth plate not less than 2.25 Metre deep below ground level) with top edge of the plate not less than 1.5 metre below normal ground level connected to galvanished earth wire 4.0 mm dia by means of bolts, nuts check and washers of GI or steel all as shown in electrical plate No. 3 of SSR Pt -I connected to earthing test point all as specified or indicated including GI pipe 15 mm dia light grade for earth wire protection, necessary excavation, earth work in any type of soil, PCC chamber and RCC cover slab, connecting lead wire from test point to DB complete all as specified & as directed

M/s godara infratech and power industries

AMBEY MAA CONSTRUCTION COMPANY

Devi Engineeing

M/S Dharam Chand Lal Chand Jain

M/s Malinath Electricals