CERTAIN REPAIR TO JOINERY, FLOORING, SEEPAGE AND ROOF TREATMENT IN MD ACCN OF JCOs ORs IN ZONE-III AREA AT JAIPUR MIL STN UNDER GE (S) JAIPUR

Amount

Taking down chowkat or frames with shutters (with out taking off shutters from the frame) n. exe 1.50 SQM each as directed.

All as per item No 1 above but exe 1.50 SQM but n .exe 4.00 SQM each.

Taking down shutters of any description exc 1.00 sqm but n exc 2.50 sqm each

Taking down shutters of any description n exc 1.00 Sqm each

S&F Pressed steel frames 125 x 60mm size for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed, complete all as specified and as directed by Engr-in-Charge.

S&F Pressed steel frames 105x60mm sieze for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete as specified, supplied and fixed, complete all as specified and as directed by Engr-in-Charge.

M&L, PCC 1:3:6 type C1 (20 mm graded agg.) as in filling of pressed steel door frame, complete all as specified and as directed by Engr-in-Charge.

S&F 35mm thick 2nd class HW rail and style factory made plain, framed, panelled shutter (any numbers of panels ) with lock rail & panel of 9mm BWP commercial ply or 12mm veneered particle board with commercial veneering on both faces. The size of rail & steel as per IS:1003 (Part-I) kiln seasoned & chemically pressure treated supplied and fitted to chowkates complete all as specified.

S&F IInd class Hard Wood 35mm thick Factory made Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc. (without sash bars), edges of framing plain, chamfered or rounded. fitted with cut and mitred beads for securing glass, etc.; sizes of me-mbers of shutters as specified in SSR Part I, Section 8, clause 8.24 (a); supplied and fitted to chowkats all as specified.

M&L Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, suppling & fixing in opening as per specification & drawing

M&L Factory made solid panel pvc door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top & bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC `C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; Panelling of plain colour PVC sheet to be fitted in the M.S frame wedded/ sealed to the stiles, & rails with suitable PVC sheet beading, and joined together with solvent cement, suppling & fixing in the frame at site as per specification & drawing.

M&L Powder Coated (minimum thickness of powder coating 50 micron) 7Anodised aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete including making good disturbed portion with CM 1:4 or PCC 1:2:4 type B0 all as specified

M&L Powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium door shutters, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified. Note: Rate shall be inclusive of 4.8mm thick plain sheet for glazing etc.

M&L Powder Coated (minimum thickness of powder coating 50 micron) Anodised aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified. Note: Rate shall be inclusive of 4.8mm thick plain sheet for glazing etc.

M&L Powder Coated (minimum thickness of powder coating 50 micron)Anodised aluminium window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified. Note: Rate shall be inclusive of 4.8mm thick plain sheet for glazing etc.

M&L Aluminium powder coated (minimum thickness of powder coating 50 micron) door/window shutter openable/ sliding type with aluminium section weighing 0.35 Kg/ Mtr incl. necessary joining, cleats, glazing clips, rubber packing aluminium powder coated snap beading, screws, handle & tower bolt etc complete all as specified. Note: Rate shall be inclusive of 4.8mm thick plain sheet for glazing etc.

S&F in repair aluminimum (Die cast ) body door closer hydraulically regulated, designation No 2 universal type , suitable for dooe shutter of 701-850mm in width and of weight between 36 to 60 Kg complete all as specified and directed.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded complete as specified.

All as per item No. 18 above but without glazing bars complete all as specified.

S&F Mild steel, steel ventilators with top hung shutter including hinges,steel peg stay, complete Including taking down existing steel ventilators

S&F Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work confirming to Fe.290.Gde-E-165 complete as specified.

S&F 100 mm butt hinges medium weight cold rolled mild steel, ISI marked, fixed to chowkats/ other chowkhats including welding etc complete.

S&F 300 mm long MS sliding door bolt of stove enameled black (clip type)with bright bolt not less than 12 mm dia with and including a iminimum of 6 bolts and nuts complete fitted all as specified and directed .

S&F mild steel barrel tower bolt stove enamelled black with bright bolt 150 mm long all as specified.

S&F mild steel pressed handle ovel type stove enamelled black with bright bolt 125 mm long all as specified.

S&F galvanised mild steel wire cloth 0.56 mm nominal dia of wire with average width of aperture 1.18 mm fixed with tinned tacks or galvanised wire stapels fixed etc complete all as specified and directed.

M&L for preparation of new wooden surfaces of any description over 10 cm in width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L for preparation of new steel surfaces of any description over 10 cm in width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer Complete all as specified and directe

S&F Aluminium, anodised, barrel tower bolts 150mm long of extruded section complete as specified.

S&F Aluminium alloy, anodised, sliding door bolt 300 mm long with hasp, staple (bolt type) & fixing clips of sheet, cast or extruded sections & sliding bolts of extruded sections complete all as specified and as directed

S&F Aluminium handles 125 mm size, cast type, anodised complete all as specified and as directed

S&F 4.00 mm thick sheet glass of ordinary quality and glazing with oil putty in square or fixed with beads in squares nexe 0.50 SQM in each pane complete all as specified and directed.

Demolition of brick work built in cement mortar including all quoins arches , pillers etc all as specified and directed

M&L for brick work with dub class ' B ' bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar 1:4 complete all as specified and directed..

Taking down plastering cement plaster or cement lime plaster on brick or stone walls including raking out joints hacking for key, scrubbing down with water any description all as specified and directedany of description of wall all as specified.

M&L for rendering 15 mm th in cement mortar 1:6 on wall of brick work or concrete surfaces finished fair and even complete all as specified and directed.

M&L for rendering 15 mm th in cement mortar 1:4 on wall of brick work or concrete surfaces finished fair and even complete all as specified and directed.

M&L Preparation of new plastered surfaces of walls, pillars & cornices & applying two coat of cement base paint on wall complete all as specified.

M&L for preparing the new plastered surfaces and applying two coats of oil bound distemper over a coat of prirmer on wall complete all as specified and directed.

Taking down old and S&F pressed steel cup board shutters with frame , the frame shall be made of 1.25 mmthick and shutter made of 1.00 mm thick PBI sheet with 6 Nos 100 mm long steel hinges , Godrej pattern locking arrangement including 12mm dia vertical rod all as per TD drg No CEJZ /TD 2004/29 . The surfaces shall be spary painted with two coat of synthetic enamel paint over a coat of zinc chromate primer over cleared surface complete all as specified and directed and shown on drg (Total width including frame shall be measured flat and paid).

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premises.

M&L for coloured Glazed ceramic tiles in vertical surfaces of size 300mm x 450mm, 7mm thick edge cut over and including 10 mm thick bedding layer in CM 1:4 , set and jointed in neat cement slurry and pointed in white or coloured cement to match all as directed by Engineer-in-charge.

M&L for coloured Non Skid Ceramic tiles 7 to 8mm thick (square/rectangular) area of each tiles edge cut exceeding 0.06 sqm but not exceeding 0.11 sqm , in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match and screed bed or bedding layer of cement mortar 1:6, 15 mm thick complete all as specified.

M/L coloured Non skid ceramic tiles 7 to 8 mm thick (square/rectangular) area of Each tile exceeding 0.18 Sqm but not exceeding 0.38 Sqm , in floors etc set jointed in neat cement slurry and pointed in white or coloured cement match over 15 mm thick screed bed in CM(1:4) completed all as specified

M&L Machine cut kota stone slab flooring 20-25mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete over 15 mm thick screed bed in CM 1:4 complete all as specified.

S & F in repair Double action floor spring hydraulically regulated made up of minimum 1.25 mm thick aluminium alloy sheet foundation box, main body with stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty , complete all as specified

S&F sheet galss 4mm thick , oridnary quality & glazing with oil putty in square n exc 0.5 sqm in each pane sheet glass, ordinary quality, if sheet glass is ground or obscured or frosted, on one side complete all as specified.

Hacking out old broken glass pane (any thickness, size, quality , description)from metal /wood frame including punching or drilling out old glass panes, pins, springs clips & fixing 3.00 mm thick sheet glass of ordinary quality and glazing in square as required as directed by Engr -in-Charge.

Hacking out old broken glass pane (any thickness, size, quality , description)from metal /wood frame including punching or drilling out old glass panes, pins, springs clips & fixing 3.00 mm thick frosted glass of ordinary quality and glazing in square as required as directed by Engr -in-Charge.

Demolition of Cement Concrete in ground floors and pavings n exc 15 cm thickness (below or above ground level), complete all as specified

M&L for PCC 1:2:4 type B1 using 20mm graded stone aggregate as in sub-base flooring 75mm thick finished even and fair without using extra cement. complete all as specified.

M&L for 25 mm thick Cement concrete type B-1, 1:2:4 (20mm graded aggregate) finished fair and even all as specified.

M&L for machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60mm tickness , M-35 grade, set, jointed over 25 mm thick sand cushoning all as directed by Engineer-in-Charge.

M&L Providing and laying at or near ground level precast factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete as specified.

M & L for Brickwork with subclass `B' bricks, straight or curved on plan exc 6m mean radius, built in CM (1:6), complete all as specified

Dismantling of old water tanks and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 500 Ltrs Capacity, complete all as specified

Dismantling of old water tanks and S&F Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) hoisted & fixed in position all as specified in SSR Part I 1000 Ltrs Capacity, complete all as specified

S&F in repair Ball brass valves 20mm bore, high pressure, with polythene float & flynut complete, screwed for iron pipe or brass ferrule

S&F in repairs Bib taps 15 mm bore, cast copper alloy with crtuch or butterfly handle,screwed down, screwed for iron pipe or for brass ferrule of fancy type

S&F in repair stop valve 15mm, copper alloy, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or for unions complete all as specified.

Dismantling and taking up or down the existing unserviceable GI pipe and M&L for new galvanised 15 mm bore steel water tubing medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified

All as per item no 62 but 20 mm bore complete all as specified

All as per item no 62 but 25 mm bore complete all as specified

S&F in repairs sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes, including waste coupling & waste pipe, bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420 Complete all as specified

S&F in repairs Vitreous China squatting pan 'orissa ' pattern `, size 580mmX 440 mm white ,with integral foot rests,(exclusing flushing cistern & flush pipe) including connection to trap and to flush pipe etc including set in and including concrete

S&F in repair Vitreous China bowl urinal flat back, size of 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe including PVC Pipe (excluding flushing cistern, flush pipe and waste pipe) complete all specified

S&F in repair Vitreous China wash basin , coloured oval sape, size 550x400mm but including brackets, coupling and wast pipe complete all specified

S&F in repair 15mm bore CP fancy type Pillar taps, cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with or without lettered `Hot' or `Cold' with long screwed shanks and fly-nuts, screwed for iron pipe complete all as specified.

S&F in repair Stop valves 15 mm bore fancy type, CP with long shank & cup (conncelaed type), cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions

S&F in repair Swivel shower of PTMT any colour for fixing with 15mm pipe (min. weight 40gms)

S & F in repair Grating doom 125 mm dia of with waste hole of PTMT

S&F in repair MS spring hinges 300 mm, ordinary rat tail rod pattern including roller and roller plate complete fixed to wooden/ angle iron chowkats ., complete all as specified

M&L in repair PVC Flushing cistern 10 ltr capacity white, with inlet, ball valve, float and handle, high or low level including bracket & 32 mm dia flush pipe etc. Complete all as specified

S&F in repair Flush pipe of polyethylene of low or high density of PVC, 32 mm dia, for low level cistern

S&F in repair PVC connections 15mm size with PTMT nuts of length 450mm complete all as specified.

S&F in repair PVC Waste Pipe 32 mm bore for WHB & urinal complete all as specified

S&F in repairs angle stop cock 15 mm bore, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions fancy type chromium plated

Welding in repairs. Exc 2.5cm but n.exc 5 cm in length and exc 6 mm but n.exc 9 mm thickness of metal

Running welding in repairs n.exc 6 mm thick

Demolition of PCC in roof covering, kerbs, roof kerbs, benching, coved fillets etc including old decayed water proofing treatment of any type all as directed by Engineer-in-charge.

M&L for surface preparation by removal of all loose particle to ensure clean, smooth and dry surface and laying 25mm thick PCC type B-0, (1:2:4) using 12.5mm graded stone aggregate finished even & smooth without using extra cement to cover negative slope into prop with WPC @ 3% weight of cement.

M&L painting with one coat of polymeric primer @ 0.30 Kg per sqm, conforming to IS : 3384. A layer of APP based polymeric membrane, 3 mm thick (min), weighing not less than 3.5 Kg/m2 reinforced with polyster non woven fabric ( weighing not less than 150 gms/ Sqm). Application of polymeric membrane shall be by torch application all as per manufacturer instructions. and finally applying one coat of bitumen @ 1.2 kg/sqm on APP membrane complete all as specified.

M&L one coat of aluminium paint over APP Membrane all complete as specified

Supplying only Integral waterproofing compound

M&L PCC 1:2:4 mix type B-0(using 12.5mm graded aggregates) as in roof kerbs rounded or chambered on edge., complete all as specified

Deep Construction Company

UNIVERSAL INFRAPROJECT PVT LTD

Chaudhary Constructions

JAGDAMBA CONSTRUCTION COMPANY

MSR INFRATECH