JH-LWE-LAT-05/21-22

Amount

ROAD-1 JAGALDAGA TO BANHARDI , BLOCK LATEHAR - DIST. LATEHAR LENGTH-4.80 KM

SETTING OUT @ 4.800 KM

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. as per Technical Specification Clause 201. (SOR-2.2)

EARTH WORK Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (including royality @ Rs. 24.00 per cum, watering, rolling & compaction) as per Technical Specification (SOR-3.5-(I))

Construction of sub grade and earthen shoulder (construction of Sub grade and earthen shoulders with approved material obtained from borrow area pits with all lifts and leads, transportation to site spreading grading to required slope and compacted to meet requirement of table no. 300-2) (Sor 3.18 (i))

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

(i) Free Lead- 70%

(ii) Lead Upto 250 m-15%

(iii) Lead Upto 500 m-15%

SUB BASE Gravel/Soil-Aggregate Surface Course (Table 400.3) - Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402 MOORUM

Construction of granular sub-base (GSB) by providing course graded Material Grading-2 (Table:-400-2), mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

BASE COURSE Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom

Providing and laying semi dense bituminous concrete (SDBC) with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects.

MISCELLANEOUS Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc.

(ii) Ordinary kilometre stone (precast)

(iii) Hectometre stone (precast)

Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25-1967, fixed in position including finishing and lettering but excluding painting

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Providing and erecting MAINTENANCE BOARD retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of typical PMGSY LOGO Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

DRAIN Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. SOR-11.1-(I)

Sand filling below brick masonry for levelling as per drawing and technical specification

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Plastering with cement mortar (1:4), 15mm thick on brick work in substructure as per technical specification.

GUARDWALL -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing coarse clean local sand filling in foundation trenches or in plinth or under approach slab including ramming and watering, layer not exceeding 150 mm thick with all leads and lifts including cost of all labour and materials, taxes and royalty all complete job as per design, drawing specification and direction of E/I.

Plain Cement Concrete M15 in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

H.P Culvert -Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out,construction of shorting and bracing, removal of stumps and other deleterious matte, dressing of sides and bottom and backfilling with approved material.

Bedding for Pipe Type B (First Class) Bedding : Laying (First Class) bedding on well compacted sand, moorum or approved granular material as per Clause 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Providing rough dreses coarse stone masonary in C.M. (1:4) in foundation and plinth with hammer dressed stone of less than 0.03 m3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, racking out joints to 20mm depth curing, taxes and royalties all complete job as per specification.

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in single Row Providing and laying reinforced concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets as per Clause 1106.

Plastering with cement mortar (1:4),15 mm thick on stonework in substructure as per technical specification Clauses 613.4 & 1204

Providing White washing, theree coats over new surface with approved quality of Lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffloding, washing of floors and taxes all complete as per specification.

Maintenance Cost 1st yr

Maintenance Cost 2nd Yr

Maintenance Cost 3rd Yr

Maintenance Cost 4th Yr

Maintenance Cost 5th Yr

ROAD-2 KONE TO NARESHGARH , BLOCK LATEHAR - DIST. LATEHAR LENGTH-2.150 KM

SETTING OUT @ 2.150 KM

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. as per Technical Specification Clause 201. (SOR-2.2)

Scarifying existing bituminous surface to a depth of 50mm and disposal of scarified material with in all lifts and lead upto 1000 m by Mechanical means (3.15)

EARTH WORK Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (including royality @ Rs. 24.00 per cum, watering, rolling & compaction) as per Technical Specification (SOR-3.5-(I))

Construction of sub grade and earthen shoulder (construction of Sub grade and earthen shoulders with approved material obtained from borrow area pits with all lifts and leads, transportation to site spreading grading to required slope and compacted to meet requirement of table no. 300-2) (Sor 3.18 (i))

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

(i) Free Lead- 70%

(ii) Lead Upto 250 m-15%

(iii) Lead Upto 500 m-15%

SUB BASE Gravel/Soil-Aggregate Surface Course (Table 400.3) - Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402 MOORUM

Construction of granular sub-base (GSB) by providing course graded Material Grading-2 (Table:-400-2), mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

BASE COURSE Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom

Providing and laying semi dense bituminous concrete (SDBC) with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects.

RIGID PEVEMENT Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

MISCELLANEOUS Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M15 grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc.

(i) 5th kilometre stone (precast)

(ii) Ordinary kilometre stone (precast)

(iii) Hectometre stone (precast)

Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25-1967, fixed in position including finishing and lettering but excluding painting

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Providing and erecting MAINTENANCE BOARD retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of typical PMGSY LOGO Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

DRAIN Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. SOR-11.1-(I)

Sand filling below brick masonry for levelling as per drawing and technical specification

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Plastering with cement mortar (1:4), 15mm thick on brick work in substructure as per technical specification.

GUARDWALL -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing coarse clean local sand filling in foundation trenches or in plinth or under approach slab including ramming and watering, layer not exceeding 150 mm thick with all leads and lifts including cost of all labour and materials, taxes and royalty all complete job as per design, drawing specification and direction of E/I.

Plain Cement Concrete M15 in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

H.P Culvert -Excavation for Structures Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out,construction of shorting and bracing, removal of stumps and other deleterious matte, dressing of sides and bottom and backfilling with approved material.

Bedding for Pipe Type B (First Class) Bedding : Laying (First Class) bedding on well compacted sand, moorum or approved granular material as per Clause 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Providing rough dreses coarse stone masonary in C.M. (1:4) in foundation and plinth with hammer dressed stone of less than 0.03 m3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, racking out joints to 20mm depth curing, taxes and royalties all complete job as per specification.

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in single Row Providing and laying reinforced concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets as per Clause 1106.

Plastering with cement mortar (1:4),15 mm thick on stonework in substructure as per technical specification Clauses 613.4 & 1204

Providing White washing, theree coats over new surface with approved quality of Lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffloding, washing of floors and taxes all complete as per specification.

RCC Culvert -1Nx1.0mx1.0m Earthwork in excavation in foundation trenches -do- -do- all complete job as per specification and direction of E/I.

(a) 60% qty for Hard soil (A)

(b) 40% qty for Soft rock (B)

Providing PCC M-10 with nominal mix of (1:3:6) etc as per specification -do- -do- all complete job as per specification and direction of E/I.

Providing rough dressed stone masonary in CM (1:3) in foundation and plinth -do- -do- etc all complete job as per specification and direction of E/I.

Providing rough dressed stone masonary in CM (1:3) in Super structure -do- -do- etc all complete job as per specification and direction of E/I.

Providing Weep holes -do- -do- all; complete job as per specification and direction of E/I.

Providing PCC (1:2:4) in various components of barriage super structure etc -do- -do- all job complete as per specificationa and direction of E/I.

Providing and fixing in position 25mm thick bituminous board in expansion joint etc -do -do- all complete job as per specification and direction of E/I

Providng and laying RCC M30 with nominal mix in deck slab etc. etc -do -do- all complete job as per specification and direction of E/I

Providng and laying RCC M30 with nominal mix in Abutment Cap etc. etc -do -do- all complete job as per specification and direction of E/I

Providing MS Tor steel reinforcement (10-12 mm dia Rod) as per approved design and drawing including cutting, bending, and binding and placing in position as per specification and direction of E/I.

Providing 15mm thick cement plaster in CM (1:4) -do- -do- all complete job as per specification and direction of E/I.

Providing 1.5 mm punning etc -do- -do- as per specification and direction of E/I

Painting post etc with two coats of enamel paint of approved shade and make after clearing the surface etc area vide item no. 14. F I Post (pxdxh) = 3.17x0.30 x 0.60 =0.56 m²

Providing PCC M-30 with nominal mix in Wearing coat -do- -do- all complete job as per specification and direction of E/I.

Earthwork in back filling in foundation and plinth etc -do- -do- all complete job as per specification and direction of E/I.

Providing and fixing at site precast 20mm dia and 75 cm long RCC (1:2:4) with nominal reinforcement F.I. post including cost of earth cutting -do -do- all complete job.

RCC Culvert -1Nx2.0mx1.40m Earthwork in excavation in foundation trenches -do- -do- all complete job as per specification and direction of E/I.

(a) 60% qty for Hard soil (A)

(b) 40% qty for Soft rock (B)

Providing coarse clean local sand in filling in foundation and plinth -do- do- all complete job as per specification and direction of E/I

Providing PCC M-10 with nominal mix of (1:3:6) etc as per specification -do- -do- all complete job as per specification and direction of E/I.

Providing rough dressed stone masonary in CM (1:4) in foundation and plinth -do- -do- etc all complete job as per specification and direction of E/I.

Providing rough dressed stone masonary in CM (1:4) in Super structure -do- -do- etc all complete job as per specification and direction of E/I.

Providing Weep holes -do- -do- all; complete job as per specification and direction of E/I.

Providing PCC (1:2:4) in various components of barriage super structure etc -do- -do- all job complete as per specificationa nd direction of E/I.

Providing and fixing in position 25mm thick bituminous board in expansion joint etc -do -do- all complete job as per specification and direction of E/I

Providng and laying RCC M30 with nominal mix in deck slab etc. etc -do -do- all complete job as per specification and direction of E/I

Providing MS Tor steel reinforcement (10-12 mm dia Rod) as per approved design and drawing including cutting, bending, and binding and placing in position as per specification and direction of E/I.

Providing 15mm thick cement plaster in CM (1:4) -do- -do- all complete job as per specification and direction of E/I.

Providing 1.5 mm punning etc -do- -do- as per specification and direction of E/I

Providing (1:4) in ceiling etc as per specification and direction of E/I.

Painting post etc with two coats of enamel paint of approved shade and make after clearing the surface etc area vide item no. 15

Earthwork in back filling in foundation and plinth etc -do- -do- all complete job as per specification and direction of E/I.

Providing PCC M-30 with nominal mix in Wearing coat -do- -do- all complete job as per specification and direction of E/I.

Providing and fixing at site precast 20mm dia and 75 cm long RCC (1:2:4) with nominal reinforcement F.I. post including cost of earth cutting -do -do- all complete job.

Maintenance Cost 1st Yr

Maintenance Cost 2nd Yr

Maintenance Cost 3rd Yr

Maintenance Cost 4th Yr

Maintenance Cost 5th Yr

ROAD-3 NARESHGARH TO KUDUPANI TALAI , BLOCK LATEHAR - DIST. LATEHAR LENGTH-3.00 KM

SETTING OUT @ 3.000 KM

Clearing and grubbing road land including uprooting rank vegetation, grass, bushes, shrubs, saplings and trees girth up to 300 mm, removal of stumps of trees cut earlier and disposal of unserviceable materials and stacking of serviceable material to be used or auctioned, up to a lead of 1000 metres including removal and disposal of top organic soil not exceeding 150 mm in thickness. as per Technical Specification Clause 201. (SOR-2.2)

EARTH WORK Excavation for roadwork in soil with hydraulic excavator of 0.9 cum bucket capacity including cutting and loading in tippers, trimming bottom and side slopes, in accordance with requirements of lines, grades and cross sections, and transporting to the embankment location within all lifts and lead upto 1000m (including royality @ Rs. 24.00 per cum, watering, rolling & compaction) as per Technical Specification (SOR-3.5-(I))

Construction of sub grade and earthen shoulder (construction of Sub grade and earthen shoulders with approved material obtained from borrow area pits with all lifts and leads, transportation to site spreading grading to required slope and compacted to meet requirement of table no. 300-2) (Sor 3.18 (i))

Construction of embankment with approved materials deposited at site from roadway cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of table 300-2.

Construction of embankment with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacting to meet requirement of table 300-2.

(i) Free Lead- 70%

(ii) Lead Upto 250 m-15%

(iii) Lead Upto 500 m-15%

SUB BASE Gravel/Soil-Aggregate Surface Course (Table 400.3) - Construction of granular surface course by providing well graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with three wheel 80-100 kN static roller capacity to achieve the desired density, complete as per Technical Specification Clause 402 MOORUM

Construction of granular sub-base (GSB) by providing course graded Material Grading-2 (Table:-400-2), mixing in a mechanical mix plant at OMC, carriage of mixed Material to work site, spreading in uniform layers with motor grader on prepared surface and compacting with vibratory power roller to achieve the desired density, complete as per clause 401

BASE COURSE Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the Material with water at OMC in mechanical mix plant carriage of mixed Material by tipper to site, laying in uniform layers with paver in sub- base / base course on well prepared surface and compacting with vibratory roller to achieve the desired density.

Providing and applying primer coat with bitumen emulsion on prepared surface of granular Base including clearing of road surface and spraying primer at the rate of 0.60 kg/sqm using mechanical means.

Providing and applying tack coat with bitumen emulsion using emulsion pressure distributor at the rate of 0.20 kg per sqm on the prepared bituminous/granular surface cleaned with mechanical broom

Providing and laying semi dense bituminous concrete (SDBC) with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects.

RIGID PEVEMENT Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing

MISCELLANEOUS Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and erecting direction and place identification retro- reflectorised sign as per IRC :67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area exceeding 0.9 sqm supported on a mild steel angle iron post 75 mm x 75 mm x 6 mm, 2 Nos. firmly fixed to the ground by means of properly designed foundation with M 15 grade cement concrete45 cm x 45 cm x 60 cm, 60 cm below ground level as per approved drawing

Reinforced cement concrete M15grade kilometre stone of standard design as per IRC:8-1980, fixing in position including painting and printing etc.

(ii) Ordinary kilometre stone (precast)

(iii) Hectometre stone (precast)

Reinforced cement concrete M15 grade boundary pillars of standard design as per IRC:25-1967, fixed in position including finishing and lettering but excluding painting

Painting two coats after filling the surface with synthetic enamel paint in all shades on new plastered concrete surfaces

Providing and erecting MAINTENANCE BOARD retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminium sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

Providing and fixing of typical PMGSY LOGO Sign Board with Logo as per MORD specifications and drawing. Three MS Plates of 1.6mm thick top and middle plate duly welded with MS flat iron 25mmx5m size on back on edges. The lower plate will be welded with MS angle iron frame of 25mmx25mm x5mm. The angle iron frame of the lower most plate and flat iron frame of middle plate will be welded to 2 nos. 75mm x 75mm x 12 SWG sheet tubes posts duly embedded in cement concrete M-15 grade blocks of 450mm x 450mm x 600mm, 600mm below ground level. The top most diamond plate will be welded to middle plate by 47mm x 47mm of 12 SWG steel plate tube. All MS will be stoe enameled on both sides. Lettering and printing arrows, border etc will be painted with ready mixed synthetic enamel paint of superior quality in required shade and colour. All sections of framed posts and steel tube will be painted with primer and two coats of epoxy as per drawing.

Direction and Place Identification Signs upto 0.9 sqm Size Board. Providing and erecting direction and place identification retro-reflectorised sign as per IRC:67 made of high intensity grade sheeting vide clause 801.3, fixed over aluminum sheeting, 2 mm thick with area not exceeding 0.9 sqm supported on a mild steel single angle iron post 75 x 75 x 6 mm firmly fixed to the ground by means of properly designed foundation with M15 grade cement concrete 45 x 45 x 60 cm, 60 cm below ground level as per approved drawing

GUARDWALL -Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material.

Providing coarse clean local sand filling in foundation trenches or in plinth or under approach slab including ramming and watering, layer not exceeding 150 mm thick with all leads and lifts including cost of all labour and materials, taxes and royalty all complete job as per design, drawing specification and direction of E/I.

Plain Cement Concrete M15 in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Stone masonry in cement mortar (1:4) random rubble masonry for foundation complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Stone masonry in cement mortar for substructure complete as per drawing & technical specification Clauses 702, 704, 1202 and 1204

Providing concrete for plain/reinforced concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203

Providing weep holes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Back filling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8

H.P Culvert -Excavation for Structures (1x1000M DIA ) Earthwork in excavation for foundation of structures upto 3 m depth as per drawing and technical specification Clause 1104 includding setting out,construction of shorting and bracing, removal of stumps and other deleterious matte, dressing of sides and bottom and backfilling with approved material.

Bedding for Pipe Type B (First Class) Bedding : Laying (First Class) bedding on well compacted sand, moorum or approved granular material as per Clause 1105 (ii)

Plain Cement Concrete M10 (1:3:6 nominal mix) in levelling Coarse below open foundation of Head walls as per drawings & Technical Specification Clause 1109

Providing rough dreses coarse stone masonary in C.M. (1:4) in foundation and plinth with hammer dressed stone of less than 0.03 m3 in volume and clean coarse sand of F.M. 2 to 2.5 including cost of screening, racking out joints to 20mm depth curing, taxes and royalties all complete job as per specification.

Providing and Laying Reinforced Cement Concrete Pipe NP3 as per design in single Row Providing and laying reinforced concrete pipe NP3 for culverts on first class bedding of granular material in single row including fixing collar with cement mortar 1:2 excluding excavation, protection works, backfilling, concrete and masonry work in head walls and parapets as per Clause 1106.

Plastering with cement mortar (1:4),15 mm thick on stonework in substructure as per technical specification Clauses 613.4 & 1204

Providing White washing, theree coats over new surface with approved quality of Lime including cost of cleaning surface thoroughly and removing the scales of smoke and mash marks with jhama rubbing scaffloding, washing of floors and taxes all complete as per specification.

RCC Culvert -1Nx3.0mx2.5m E/W in excavation of foundation trenches in hard soil -do-do-all complete job

Providing P.C.C. M15 with nominal mix(1:2:4)in foundation -do-do-all complete

Providing R.D.R.R. stone masonary with c.m.(1:3) in foundation and plinth -do-do-all complete

Providing R.D.R.R.Stone masonary with c.m.(1:3) in superstructure -do-do- all complete as per spn. And direction of E/I

Providing and laying boulders apron on river bed for protection against scour with stone boulders weighing not less than 40 kg each complete as per drawing and Technical specification.

Providing R.C.C. M25 in deck slab -do-do-all complete job

Providing R.C.C. M30 in wearing coat -do-do-all complete job

Providing P.C.C. M20 in various parts of the structure -do-do-all comp

Providing HYSD bars for R.C.C.

Providing Designation 75A B/W in c.m.(1:3) in foundation and plinth -do-do- all comp.

Providing 75x75mm weep holes @1000mm C/C both horizontally and vertically -do-do-all complete job

Providing 12 mm thick plaster with c.m.(1:3) -do-do- all comp. job.

Providing painting two coats over new plastered surface -do-do- all complete

Providing granular filter media -do-do-all comp.

Providing Tar Phelt Cushion under the deck slab -do-do-all complete job

Providing and fixing in position 20 mm thick premoulded joint filler in expansion joints for fixed ends of simply supported spans not exceeding 10.0m to cater for a horizontal movement upto 20 mm , covered with sealant complete as per drawing and technical specification

Providing and filling joint sealing compound as per drawing and technical specification with coarse sand and 6% bitumen by weight

Numbering and writing the culvert no. etc. -do-do- all complete

Maintenance Cost 1st Yr

Maintenance Cost 2nd Yr

Maintenance Cost 3rd Yr

Maintenance Cost 4th Yr

Maintenance Cost 5th Yr

4. HL RCC Bridge Over Auria River in Between Kone to Nareshgarh

FOUNDATION-------------Earthwork in excavation for structures as per drawing and technical specifications Clause 305.1 including setting out, construction of shoring and bracing, removal of stumps and other deleterious material and disposal upto a lead of 50 m, dressing of sides and bottom and backfilling in trenches with excavated suitable material. i) Upto 3m depth

ii) 3m to 6m depth

Providing concrete for plain concrete in open foundations complete as per drawings and technical specifications Clause 802, 803, 1202 & 1203 II. PCC Grade M-15 (Levelling Course)

Reinforced Cement Concrete (RCC M30) in Open Foundation complete as per Drawing and Technical Specifications. In Open Foundation

Supplying, fitting and placing HYSD bar reinforcement in foundation complete as per drawings and technical specifications Clauses 1000 and 1202

SUBSTRUCTURE-----------Plain/reinforced cement concrete in substructure complete as per drawings and technical specification Clauses 802, 804, 805, 806, 807, 1202 ans 1204 (RCC M30) i) Upto 5m height

Supplying, fitting and placing TMT bar reinforcement (Fe 500) in substructrue complete as per drawings and technical specification Clauses 1002, 1005, 1010 & 1202

Supplying, fitting and fixing in position true to line and level POT-PTFE bearing consisting of a metal piston supported by a disc or unreinforced elastomer confined within a metal cylinder, sealing rings, dust seals, PTFE surface sliding against stainless steel mating surface, complete assembly to be of cast steel/fabricated structural steel, metal and elastomer elements to be as per IRC: 83 part-I & II respectively and other parts conforming to BS: 5400, section 9.1 & 9.2 and clause 2006 of MoRTH Specifications complete as per drawing and approved Technical Specifications.

Providing weepholes in brick masonry/stone masonry, plain/reinforced concrete abutment, wing wall, return wall with 100 mm dia AC pipe extending through the full width of the structures with slope of 1(V):20(H) towards drawing face complete as per drawing and technical specification Clauses 614, 709, 1204.3.7

Backfilling behind abutment, wing wall and return wall complete as per drawings & technical specification Clause 1204.3.8 II) Sandy Material

Providing and laying filter media with granular crushed aggregates as per specification to a thickness of not less than 600 mm with smaller size towards the soil and bigger size towards the wall and providing over the entire surface behind abutment, wing wall, return wall to the full height, compacted to firm condition complete as per drawing and technical specification Clause 1204.3.8

SUPERSTRUCTURE-------------Providing and laying reinforced cement concrete in superstructure complete as per drawing and technical specifications Clauses 800, 1205.4 and 1205.5 II. RCC M-35

Supplying, fitting, and placing HYSD bar reinforcement (Fe 500) in superstructure complete as per drawing and technical specifications Clauses 1002, 1010 and 1202

Providing and laying cement concrete wearing course M30 grade including reinforcement complete as per drawing and technical specifications Clauses 800 and 1206.3

Construction of R.C.C. railing of M 25 grade in cast-in-situ with 20 mm nominal size aggregate, true to line and grade, tolerance of vertical railing post not to exceed 1 in 500, centre-to-centre spacing between vertical posts not to exceed 2000 mm as per drawing and technical specifications Clauses 800, 900 and 1208.3

Drainage Spouts complete as per drawing and technical specifications Clause 1209

P.C.C. M-15 ordinary grade (1:2.5:5) levelling course below approach slab complete as per drawing and technical specificatios Clauses 800 & 1211.

Reinforced Cement Concrete M-25 grade approach slab including reinforcement and formwork complete as per drawing and technical specifications Clauses 800 and 1211

Providing and laying of a strip seal expansion joint catering to maximum horizontal movement upto 70 mm, complete as per approved drawings and standard specifications to be installed by the manufacturer/supplier or their authorised representative ensuring compliance to the manufacturer's instructions for installation.

White Washing of Parapet Walls White washing two coats on parapet walls and tree trunks including preparation of surface by cleaning, scapping, etc. as pre technical specification Clause 1915

PROTECTION WORK---------------Providing and laying boulder pitching on slopes laid over prepared filter media as per drawing and technical specifications Clause 1302

Providing and laying filter material underneath pitching in slopes complete as per drawing and technical specifications Clause 1302

Part-6: Cost of Approach Road--------------Clearing and Grubbing Road Land ( By manual means) including uprooting wild vegetation , grass ,bushes ,shrubs , saplings and trees of girth upto 300mm , removals of stumps of such trees cut earlier & disposal of unserviceable materials & stacking of serviceable materials to be used or auctioned upto a lead of 1000 m including removal and disposal of top organic soil not exeeding 150mm in thickness as per technical specification - clause 201.1 and direction of E/I

Construction of embankment with approved material deposited at site and obtained from road way cutting and excavation from drain and foundation of other structures graded and compacted to meet requirement of tables 300.1 and 300.2 as per technical specification clause 301.5 60% of Excavated material

Construction of embankment with approved material obtained from borrow pits with a lift upto 1.5 m, transporting to site, spreading, grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 250m as per Technical Specification Clause 301.5 50% of total Qty (Free Lead)

Construction of subgrade and earthen shoulders with approved material obtained from borrow pits with all lifts and leads, transporting to site, spreading, grading to required slope and compacted to meet requirement of Table 300.2 as per Technical Specification Clause 303.1. 50% of total Qty (Lead upto 750-1000 m)

Construction of granular sub-base by providing well graded material, spreading in uniform layers with motor grader / Tractor mount grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with smooth wheel roller to achieve the desired density, complete as per Technical Specification Clause 401.

Providing, laying, spreading and compacting graded stone aggregate to wet mix macadam specification including premixing the material with water at OMC in mechanical mixer (Pug Mill), carriage of mixed material by tipper to site, laying in uniform layers in sub-base/base course on a well prepared sub-base and compacting with smooth wheel roller of 80 to 100kN weight to achieve the desired density including lighting, barricading and maintenance of diversion, etc as per Tables 400.11 & 400.12 and Technical Specification Clause 406.

Providing and applying primer coat with bitumen emulsion (SS-1) on prepared surface of granular base including cleaning of road surface and spraying primer at the rate of 0.70-1.0 kg/sqm using mechanical means as per Technical Specification Clause 502

Providing and laying bituminous macadam with hot mix plant using crushed aggregates of grading as per Table 500.4 premixed with bituminous binder, transported to site upto a lead of 1000 m laid over a previously prepared surface with paver finisher to the required grade, level and alignment and rolled to achieve the desired compaction as per Technical Specification Clause 504.

Providing and applying tack coat with Bitumen emulsion (RS-1) using emulsion distributor at the rate of 0.25 to 0.3 kg per sqm on the prepared bituminous surface cleaned with Hydraulic broom as per Technical Specification Clause 503.

Providing and laying semi dense bituminous concrete with 100-120 TPH batch type HMP producing an average output of 75 tonnes per hour using crushed aggregates of specified grading, premixed with bituminous binder @ 4.5 to 5 per cent of mix and filler, transporting the hot mix to work site, laying with a hydrostatic paver finisher with sensor control to the required grade, level and alignment, rolling with smooth wheeled, vibratory and tandem rollers to achieve the desired compaction as per MoRTH specification clause No. 508 complete in all respects.

Providing and fixing of retro reflective cautionary , mandatory and informatory sign board as per IRC :67 made of 1.5 mm thick MS steel duly stove white colour in front and gray colour on back with red reflective border of 65 mm width and required letters and figures with reflective tape engineering grade as per clause 1701.3.9 of MORD for rural road of required shade and colour supported and welded on 47mmx47mmx12swg sheet tube firmly fixed to the ground by mean of properly designed foundation with M15 grade cement concrete 450x450x600 mm ,600mm below ground level as per approved drawing clause 1701.2.2.

Construction of Embankment with material obtained from borrow pits with a lift upto 1.5 m , transporting to the site spreading , grading to required slope and compacting to meet requirement of Tables 300.1 and 300.2 with a lead upto 1000 m as per Technical Specification Clause 301.5 .

Grannular Sub-Base Gr-II - Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method.

Providing and laying reinforced cement concrete pipe NP3 for culverts on first class bedding of granular material in double row including fixing collar with cement mortar 1:2 but excluding excavation, protection works, backfilling, concrete and masonry works in head walls and parapets as per Clause 1106.

1st Year Maintenance

2nd Year Maintenance

3rd Year Maintenance

4th Year Maintenance

5th Year Maintenance

Labour Cess @ 1%

Sanjay Kumar Upadhyay

CHARAN MAHADEO CONSTRUCTION PVT LTD

AMIT CONSTRUCTION

M/S ASHOK KUMAR MALHOTRA