CA NO. GE AF NO.1/GUR-60/2024-25 PROVN OF CERTAIN REVENUE AND MINOR WORK IN VARIOUS LOACTION AT AF STATION GURGAON UNDER GE(AF) GURGAON NO. 1.

Amount

Schedule-A (B/R Work)

S&F for steel water tubing 15mm bore, galvanised, medium grade with and including provision of all fittings of ISI marked and connected complete all as specified and as directed by Engineer-in-Charge.

S&F for steel water tubing 20mm bore, galvanised, medium grade with and including provision of all fittings of ISI marked and connected complete all as specified and as directed by Engineer-in-Charge.

S&F 60 cm long PVC connection with two nos PTMT nut and rubber washers suitable for 15mm bore GI Pipe of existing one complete all as specified and as directed by Engineer-in-Charge.

S&F PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to wall ( 110mm bore) including flat iron claimp for proper fixing complete all as specified and as directed by Engineer-in-Charge.

S&F PVC bends 110mm dia complete all as specified by Engineer-in -Charge

S&F PVC (SWR) vent cowl for 110mm dia pipe complete all as specified by Engineer-in -Charge

S&F 15 mm brass CP mixer for mixing hot and cold water for wash basin mixer with wall flange extended operating lever, swinging spout complete all accessories as required complete all as specified and as directed by Engineer-in-Charge.

S&F bib taps 15mm bore long body cast copper alloy fancy type chormium plated butter fly handle screwed down including complete all as specified and as directed by Engineer-in-Charge.

S&F angle/ stop valves 15mm bore (for iron pipe) fancy type chromium plated screwed down high pressure with butterfly handle screwed both ends complete all as specified and as directed by Engineer-in-Charge.

S&F for vitreous china wash basin hand white flat backsize 600x480mm including cutting for and pinning in ends of brackets including fixing of 32 mm low dencity polylethyne pipes (LDPE)of pressure rating 6kg/cm2,cupling ,PVC connection with 15 mm dia PTMTcheknuts ,brackets all complete all as specified and as directed by Engineer-in-Charge.

S&F 20mm Gate valves, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete in all respect as specified and directed by Engr-in-Charge.

S&F PVC (SWR) ( 110mm bore) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and as directed by Engineer-in-Charge.

M&L for 100mm dia pipe, Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required, complete all as specified and as directed.

M&L for cement concrete 1:3:6 (20mm Graded crushed stone aggregate) Bed for drain pipes of bore 100mm including packing under and haunching against the sides of pipes after they are laid in foul condition and testing, complete all as specified and as directed.

M&L providing 75mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for 100 mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) in floor complete all as specified and directed by Engr-in-Charge

M&L glossy chequered cement concrete tiles 300x300x25mm thick, set jointed and pointed in near cement slurry in floors with white cement and pigments in any colour machine preassed glazed , over cement screed bed 15mm thick cement motor 1:6 all as specified and as directed by Engr-in-charge.

Demolition of Brick Work built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions, complete all as specified and as directed.

M&L for Brick work with sub-Class ‘B’ bricks (with old size bricks), straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4, complete all as specified and as directed.

Taking down cement or cement lime plaster of any description on bricks wall etc including raking out joints, hacking for key, scrubbing down with water etc all as specified and directed by Engineer-in-Charge

M&L 15mm thick rendering other then fair faces of brick work or concrete surfaces in CM 1:6, finished even and smooth (without using extra cement) all as specified and directed by Engineer-in-Charge.

M&L for Preparing New Plastered Surfaces of WALLS and applying TWO COATS of DISTEMPER OIL EMULSION (OIL BOUND WASHABLE DISTEMPER) over a Coat of CHALK WHITING, complete all as specified and as directed. by Engineer-in-Charge. (Note:- work will be strictly executed by mechinised means/ tools as required for smart periodical services).

M&L for complete removal of existing treatment from old decorated plastered surfaces of walls by Vacuum based sanding machine complete all as specified, removal of nails etc & filling cracks/hole with putty, applying wall care putty upto 1mm thick as required (multipurpose mixer shall be used for uniform and proper mixing of putty) and applying two coats oil emulsion distemper white or coloured over a coat of approved primer by auto roller complete all as specified & directed by Engineer-in-Charge.

Demolition of reinforced cement concrete in roofs, floors (other than ground floors), beams, staircases, landing,chajjas and similar suspended work all as specified and directed by Engineer-in-Charge.

Dismantling of wall/ floor tile including backing coat any description or any thickness beded and pointed in any cement motar and removal to out of MD land all as specified and directed by Engr-in-Charge

M&L non skid ceramic coloured tile 7 to 8mm thick (square/rectangular area of each tiles exceeding 0.11 Square but not exceeding 0.18 Sqm in floor over 15mm thick screed bed in cement motar 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match the tile all as directed by Engr-in-Charge.

M&L for glazed ceramic coloured designer concept tiles matching with existing tile 350x250x7 or 450x350x7mm size as in walls set and jointed in neat cement slurry over 10mm thick recuing in cement mortar (1:4) and pointed in coloured cement to match for work on vertical surface such as skirting dado etc all as specified and as directed by Engr-in-Charge.

M&L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms, self slab and like cement screed bed 20 mm thick in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including mirror polishing and bull nosing edging in any position etc all as directed by Engr-in-Charge.

M&L for Excavating soft/ loose soil in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits,manholes, pier holes, etc. n.exc 10 sq m on plan and n exc 1.5 m in depth and getting out all as specified and as directed by Engr-in-charge

M&L for Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm all as specified and as directed by Engr-in-charge.

Removing excavated material n.exc 50 m and depositing where directed at a level n.exc 1.5 m above the starting point all as specified and as directed by Engr-in-charge.

S&F 5.5mm thick sheet glass plain pane best quality fixing to cabinet as sliding shutter with two track channel (inculding lock and sliding raddu ) / Aluminium/Steel/wooden Sections as in Panel of cabinet / Doors / Windows/Ventilator and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), complete and fixed all as specified and as directed.

S&F PVC Cub board cabinet of required size is fabricated using 18mm thick PVC plain celuka ply (weight not less than 11kg/sqm) fixed with SS screws and solvent cement/ adhesive to make cabinet complete as per manufacturer’s specifications complete all as specified and directed by Engr-in-charge.

S&F PVC Cub board Flush Type Shutter consisting of 18mm thick prelaminated celluca ply 18mm thick (weight not less than 11kg/sqm) cut in desired size of shutter and fixed with frame of accessory at all four edges of shutter using 13/6 size self tapping steel screws including D-type handles, piano hinges & Magnetic catchers stainless steel complete all as specified and directed by Engr-in-charge.

S&F factory made PVC Shelf/Portion of required size consisting of 18mm thick (weight not less than 11kg/sqm) plain celuka PVC ply rod for supporting the hold of shelf/partion and shall provided & edges in size 18mm as per required langth complete all as specified and directed by Engr-in-charge.

M&L for factory made PVC drawer of require size constructed by joining four 125mm (height) x 12mm PVC sheet of 12mm thick at the bottom bonded with using screw etc including all necessary fittings and fixtures,channel for sliding as per manufactures spacification and drawing complete all as specified and directed by Engr-in-charge.

M&L for Anodised aluminium snap grid (Size of grid 605 x 605mm) frame work for false ceiling and Providing and fixing Gypsum Board 12mm thick in ceiling fixed with screw as per manufacturers instructions incl taking down old fasle ceiling complete and fixed all as specified and as directed.

Excavating in post holes (or similar holes) each n exc 0.5 cum, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50 m and making good surface in soft/loose soil

S&F for MS angle iron as in posts, gate and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire etc flat iron fillets (for securing with mesh etc including all necessary drilling bolting or riveting etc and similar work confirming to Fe-290 (Gde-E-165 quality-B. Note:-Posts/struts of angle iron made to shape shall be welded to existing angle iron bracket of security wall, contractor shall make his own arrangement for welding for boundary wall by using gen sets or any alternative arrangement all as specified and directed by Engr-in-Charge.

M & L for PCC 1:2:4 type B-2 using 40 mm graded stone aggregate as in foundation, filling and mass concrete etc., all as specified.

S&F Galvanised 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (Note :- each line wire to be measured)

M&L preparing New Steel and Iron Surfaces of any descriptions, over 10 mm in width or girth and applying Two Coats of Synthetic Enamel Paint over a Coat of Red Oxide Zinc Chrome Primer, complete all as specified and as directed.

M&L Cutting holes in brick walls (exc. half brick but not exc.one brick) built in cement mortar or cement lime mortar and stone walls built in lime mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete all as specified and as directed.

M&L for 15mm thick rendering on brick or concrete surfaces in CM 1:4, finished even and smooth (without using extra cement) complete all as specified and directed by Engineer-in-Charge.

M&L for preparation of new plastered surfaces on walls and applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces including necessary scaffolding all as specified and directed by Engineer-in-Charge.

M&L for mild steel Framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe.290.Gde-E-165 complete all as specified and as directed by Engr-in-charge

S&F powder coated (Thickness or powder coating not less than 50 micron) aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified and directed by Engineer-in-Charge.

S&F powder coated (Thickness or powder coating not less than 50 micron) aluminium window and ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws etc. complete all as specified and directed by Engineer-in-Charge.

S&F 4.0mm thick sheet glass plain pane best quality fixing to Aluminium/Steel/wooden Sections as in Panel of Doors/Windows/Ventilator and Panelling Works with necessary fixing Arrangements viz Jointing Cleats, Glazing Clips, Rubber Packing, Screws, etc. or fixed with Oil Putty, as required/ordered at Site(s), complete and fixed all as specified and as directed.

S&F stainless steel wire cloth with 8% nickle 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staple complete all as specified and directed by Engr-in-Charge.

S&F Butt hinges 100mm long , extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all as specified directed by Engr-in-Charge

S&F Extruded aluminium alloy handles, fabricated type,anodised 75mm size complete all as specified and directed by Engr-in-Charge

S&F 100 mm Aluminium anodised,barrel tower bolts of extruded section and fixed to shutter complete all as specified and as directed by Engineer-in-Charge.

S&F for Anodised aluminium grill (anodised transparent or dyed to required shade according to IS: 1868 with minimum anodic coating of grade AC 15) of approved design/pattern, with approved standard section and fixed to the existing window frame with C.P. brass/ stainless steel screws @ 200 mm centre to centre, including cutting the grill to proper opening size for fixing and operation of handles and fixing approved anodised aluminium standard section around the opening, all complete as per requirement and direction of Engineer-in-charge.

M&L for Surface dressing (soft/loose soil) not exceeding 15cm deep all as specified and as directed by Engr-in-charge.

M&L for Rolling and consolidating (Power roller exc 2 tonne & n exc 5 tonne) formation surfaces in cutting complete all as specified and directed by Engr-in-Charge.

M&L for Hardcore (Broken stone or boulders) of gauge n exc. 63 mm, deposited , spread and levelled in layers n exc. 15cm thick, watered and rammed to a true surface all as specified and directed.

M&L for 75mm thick Cement concrete type B- 2, 1:2:4 (40mm graded aggregate) in floor complete all as specified and directed by Engr-in-Charge

M&L for Rough finished flat surfaces concrete Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter etc. complete all as specified and directed by Engr-in-Charge

M&L for Aluminium dividing strips (22mm width), 1.5mm thick, inserted in position, conform to design complete all as specified and directed by Engr-in-Charge.

M&L for Excavation over areas in soft/loose soil, n exc 1.5 m deep and getting out complete all as specified and directed by Engr-in-Charge

M&L for PCC 1:4:8 type D2 using (40mm graded stone aggregate) as in foundation ,filling and mass concrete completed all as specified and as directed by Engr-in-Charge.

M&L for Brick work with sub-Class ‘B’ bricks (with old size bricks), straight or curved on plan exc. 6m mean radius, built in cement mortar 1:4, complete all as specified and as directed.

M&L for plain cement concrete 1:2:4 type B-1 (using 20mm graded crushed stone aggregate as in coping and similar works including necessary form work complete all as specified.

M&L for Surface excavation n.exc (not exceeding) 30 cm deep and averaging 15cm deep and getting out all as specified and as directed by Engr-in-charge.

M&L providing 100mm thick cement concrete 1:4:8 type D-2 using 40mm graded aggregate in sub base of floor complete all as specified and directed by Engr-in-Charge.

M&L for Machine pressed precast concrete interlocking paver block With Grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness M-35 Grade all as specified and as directed by Engr-in-charge.

M&L for Sand filling under floors or in foundations including watering and consolidation all as specified and as directed by Engr-in-charge.

M&L for plain cement concrete (Type-B0 1:2:4 12.5mm graded aggregate) in roof kerbs or mud stops, rounded or chamfered on edges etc complete all as specified and directed by Engr-in-Charge.

M&L for 20mm thick granite (of any type) work (table rubbed and polished) for wall lining (veneering to wall) 12mm thick in cement mortar (1:3) and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including mirror polishing and bull nosing edging in any position etc all as directed by Engr-in-Charge.

E/M PORTION

Taking down from the existing roof / down conductor aluminium/copper strip by unscrewing from the air termination and test point etc carefully complete all as specified and directed by Engr-in-Charge

Material and labour for 20 x 3.15 mm copper strip as earth continuity conductor or main earthing lead fixed to wall on porcelain insulator of suitable size or burried in ground or drawn in conduit / pipe or fixed to pole or any other indicated situation or loop earthing etc. connected with test terminal point etc. complete including fixing with saddles and screws for fixing porcelain / epoxy insulators / conduit pipe complete all as specified and as directed.

Material and labour for 25 x3.15 mm aluminium strip as earth continuity conductor or main earthing lead fixed to wall on porcelain insulator of suitable size as a separator between wall and strip not an interval more than 45 cm connected with test terminal point etc. complete including fixing with saddles and screws for fixing porcelain / epoxy insulators / conduit pipe complete all as specified and as directed

M&L for earthing complete with galvanized steel earth plate electrode 60cmx60cmx6.3mm thick, buried directly in ground (earthpit not less than 2.25 metres deep below ground level) with top edge of the plate not less than 1.5 metres below normal ground level, connected to galvanised earth strip of 32x 6 mm by means of bolts, nuts and check nuts and washers of GI or steel all as shown in Electrical plate No 3 including earth work final with watering arrangement, wire mesh, GI pipe 20mm internal dia bore buried directly vertical and adjacent to the electrode for watering and 40mm GI Pipe 40mm dia for GI Strip , PCC pit 1:3:6 type C-1using 20mmgraded stone aggregate and RCC chamber cover in 1:2:4 type B1 of size 550 x 550mm with 8 mm dia TMT bar of 100mm C/C both ways including of returning, filling in and removal of surplus soil to a distance not exc 50 m as specified and directed including testing on completion. (Note: The rate includes conection of strip to the test box and If value is not found below 03 Ohm the earthing will be done again . No extra claim will be admissible to the contractor on this account.)

Material and labour for making PCC block of size 25 x 25 x 25 cm by providing precast cement concrete 1:2:4 type B1(using 20mm graded stone aggregate) and setting in cement mortar 1:4 for arresting GI pipe post on the roof top of the building complete all as specified and as directed

M&L for making stand post (1 m long) each made out of GI Pipe 50 mm dia medium grade for fixing on the roof top of the building, etc.complete all as specified and directed.

Dismantling and taking up existing serviceable air termination of any type and any material complete and removing from site all as specified and as directed by Engr in charge.

S&F single pointed air termination aluminium rod 300 mm long 12 mm dia of superior quality of the rod for fixing on stand post on the rooftop of the building etc. complete all as specified and directed.

Dismantling and taking up old existing unserviceable Test Point Terminal Block made of any material complete all as specified and as directed by Engr in charge.

Material & Labour for Test point terminal block made of gun metal or phosphorus bronze size 75x75x25 mm, drilled and screwed including 3 nos. 8mm dia 25 mm long hexagonal head screw and connected to copper / Aluminium / GI strip complete housed in a PVC junction box complete all as specified and as directed.

S&F in trenches/withwall/in door floor GI pipe medium grade ISI marked including jointing, testing and fitting (ISI Marked) etc complete all as specified fo the 40mm bore sizes:-(Excavation and earth work will be measured and paid seperataly)

Note :- The amount of Rs 1500/- against Schedule of Credit on Srl Page 142 shall be deducted from the total amount quoted against Sch 'A'

M/S ujjwal associates (BID ID -3159887)

H.B. Traders (BID ID -3160269)

NAVYUG VYAPARI (BID ID -3159218)