CWE/FZR- /2020-21 Special Repair to Blg No P-18 (Qtr No 01 to 08) at Neel Bhawan OR Md Accn under GE (West) Ferozepur Cantt

Amount

Demolition of reinforced cement concrete as in Roofs, floors (other than ground floors), beams, staircases, landing, chajjas and similar suspended work and removing debries outside MoD land, complete all as specified

Demolition of un-reinforced cement concrete of any description and in any position, complete all as specified.

Demolition of brick work built in cement mortar of any specification and in any position complete all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) complete all as specified.

Taking down cement plaster from brick walls of any description, racking out joints, hacking for key, scrubbing down with water etc, complete all as specified.

Dismantling CI pipe alongwith fittings of 50/75/100mm bore, below or above ground level or laid in floors, jointed in cement mortar and taking out complete all as specified.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each and refixing in the same opening, complete all as specified.

Dismantling structural steel work including doors, gates but excluding framed truss etc complete all as specified.

Excavation in trenches in soft/loose soil not exceeding 1.5 metre wide and not exceeding 1.5 metre deep and not exc 10 Sqm on plan, and getting out, compete all as specified.

Returning, filling in, earth including spreading, leveling watering and well ramming in layers each not exceeding 25cm thick each layer, complete all as specified.

Removal of surplus soil to a distance not exc. 50 metre and depositing where directed at a level not exc. 1.5 metre above the starting point complete all as specified.

Demolition and breaking up drain pipes of 150mm dia (Salt glazed stone ware, AC or Reinforced concrete) set in cement mortar complete all as specified.

M&L cement concrete bed to drain pipes including packing under, and haunching against the sides of pipes after they are laid and tested in PCC 1:4:8 type D-2 using 40mm graded stone aggregate, complete all as specified.

M&L 150 mm dia salt glazed stoneware drain pipes laid in trenches and jointed complete all as specified.

M&L for cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel in cement concrete 1:2:4 type B-l smooth finished, and reforming benching as required for 150mm pipe, complete all as specified.

Dismantling of brick tiles single layer jointed & pointed in cement mortar including removal of grass vegetation, complete all as specified.

Demolition of mud phuska in roofs, any thickness, including leeping plaster (whether full thickness removed or only a part thereof) complete all as specified.

M&L 80 mm thick average, consolidated thickness, mud phuska on flat roofs,including 25 mm thick mud plaster complete all as specified.

M&L for Rendering 10 mm in cement mortar (1:4) brick/concrete surfaces of roof, mixed with WPC (WPC shall be measured and paid seaparately), finished even and smooth without using extra cement etc, complete all as specified.

S&F 150 micron thick (transparent) polythene film with 150mm end & side laps, laid over a coat of bitumen primer @ 0.30 kg to 0.50 kg per sqm, bonded with a coat of 85/25 industrial bitumen @ 1.20 Kg/sqm and laid on roof, complete all as specified.

S&F 40 mm thick brick tiles laid over a layer of 25mm thick mud mortar and joints grouted flush in cement mortar (1:3) mixed with 5% of crude oil by weight of cement, complete all as specified.

All as per item No 21 herein before but using old brick tiles retrieved from dismantling (Item No 16 hereinbefore) including cleaning and removal of mortar from tiles, complete all as specified.

M&L for Flush pointing to roof in cement mortar (1:3) including racking out joints of brick tiles,complete all as specified.

M&L for Taking down wooden/steel chowkhats or frames with shutters (without taking off shutters from the frames) of size not exceeding 1.50 Square metre each including cutting holes in brick walls of appropriate size for insertion of cement concrete blocks for hold fasts,making good jambs with plaster in CM(1:4) to match with existing finish, complete all as specified.

All as per item No 24 herein before but size exceeding 1.5 Square metre and not exceeding 4 Square metre each.

Taking down door shutter of any description, exc 1 Sqm but not exceeding 2 sqm each, complete all as specified.

Taking up or down existing steel water tubing, 20 mm bore alongwith connections fixed/laid in any situation, complete all as specified.

Taking up or down existing steel water tubing, 15 mm bore alongwith connections fixed/laid in any situation, complete all as specified

Demolition of stone slabs and tiles of any description or thickness in floor, aprons,etc laid in bedded and pinted in any surfaces complete all as specified and directed.

M&L Precast reinforced cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in cover slab shelves and similar articles set in CM (1:4), complete all as specified.

S&F Mild steel TMT bars 10 mm dia and over as in reinforcement cut to length bent to shape required including cranking, hooking at ends and binding with mild steel wire (annealed) not less than 0.9mm dia FE-500/550 confirming to IS-1786-1985 all as specified.

S&F Mild steel TMT bars 5 mm to 10mm dia cut to length, bent to shape required including cranking, bending spirally for columns, hooking ends, as in stirrups,spacers, binders and binding with and including mild steel wire (annealed) not less than 0.9 mm dia complete, FE-500/550 confirming to IS-1786-1985 all as specified & directed.

M&L for Cement concrete (1:3:6) type C-1 using 20 mm graded stone aggregate as in 50mm thick plinth protection, surfaces finished even and fair without using extra cement, including provision of construction joints, complete all as specified and directed

M&L for PCC 1:4:8 type D2 (40mm graded aggregate) as in foundation filling and mass concrete, complete all as specified.

S&F 60 mm thick (M-35 Grade) factory made, machine pressed,precast cement concrete interlocking paver block any shape with grey cement and pigment, confirming to IS-15658:2006, set and joints grouted in fine sand, laid over and including 25 mm thick layer of sand cushioning, complete all as specified and as directed.

M&L for Brick work in cement mortar 1:6 using sub class ‘B’ old size bricks, straight or curved on plan exceeding 6 metre mean radius complete all as specified.

M&L for Rendering 15 mm thick in cement mortar (1:4) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L for Rendering 10 mm thick in cement mortar (1:6) on any face of brick walls or concrete surfaces, finished even and smooth without using extra cement, complete all as specified.

M&L Rendering 5 mm thick in cement mortar (1:3) on ceiling concrete surfaces finished even and smooth without using extra cement, complete all as specified.

Supply only integral water proofing compound ISI marked, complete all as specified.

M&L for special treatment of sunken portion of WCs and bathroom as per following stages:- Stage1:- Demolition of WC including lime concrete/ cement concrete including top finish of floor any type including removal from the site & preparing the surface of existing sunken portion of WC's with wire brush to remove all loose dirt, oil grease etc as directed. Stage 2:- Rendering 10 mm thick in cement mortar (1:4) , mixed with & including using Dr Fixit PEDICRETE URP or plaster seal of STP Ltd as per Manufacturer's instructions fishised, complete all as specified and as directed. Stage 3:- Applying one coat of Dr Fixit PRIME SEAL primer or equivalent in STP Ltd over plastered surfaces and allowed to dry for 8 hrs under touch dry condition, complete all as specified and as per Manufacturer's instructions. Stage 4:- Applying two coats of water proofing of Dr Fixit Pidifin 2K or equivalent in STP Ltd over primed fully dry surfaces of sunken portion ,complete all as specified and as per Manufacturer's instructions.(Second coat of water proofing of Dr Fixit Pidifin 2K shall be applied only after 6 hrs i.e after dry of 1st coat) Stage 5:- Again rendering 10 mm thick in cement mortar (1:4) , mixed & including using Dr Fixit PEDICRETE URP or plaster seal of STP Ltd as per Manufacturer's instructions fishised, complete all as specified and as directed. Stage 6:- All CI/PVC pipe joints shall be filled with mixture of cement ,fine sand and plaster seal of Dr Fixit PEDICRETE URP or plaster seal of STP Ltd, complete all as specified and as per Manufacturer's instructions. Stage 7:- Making holes in wall and fixing 600mm long 20 mm bore GI spout for draining out of water if any, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of walls & applying two coats of white wash, complete all as specified.

M&L Preparation of old decorated plastered or unplastered surfaces by brooming down with steel wire brush, scarping down smoke soot, mould,moss and efflorescent salts and trading oil, greasy spots and applying one coat of white wash on walls including cornices, pillasters etc, complete all as specified and as directed.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of oil bound distemper, over a coat of 3 mm thick wall care putty, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces and applying two coats of oil bound distemper, over a coat of 3 mm thick wall care putty, and a coat of primer, complete all as specified and as directed.

M&L Preparation of newly plastered surfaces of ceiling & applying three coats of white wash, complete all as specified.

M&L Preparation of old decorated plastered or unplastered by applying one coat of white wash on ceiling including cornices, pillasters etc complete all as specified and as directed.

M&L Preparation of new plastered surfaces walls etc and applying two coats of cement base paint over a coat of primer, complete all as specified.

M&L Complete removal of existing treatment and preparation of old plastered surfaces of walls and applying two coats of cement base paint over a coat of primer, complete all as specified.

M&L Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type side hung steel window with pintal hinges & 2 Nos 150 mm mild steel tower bolts to each shutter, steel handle and without glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F Factory made box type steel ventilator side/top hung with glazing bars dovetailed or welded and with one shop coat of zinc chromate primer complete all as specified and shown on Drawing No CEJZ/TD-06/07 & CEJZ/TD-07/07.

S&F 3mm thick, plain sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F 3mm thick, frosted sheet glass ordinary quality and glazing, with oil putty or with wooden beads (supplied alongwith shutters), in squares n.exc 0.50 Sqm complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 125 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made pressed steel frames made of 1.25 mm thick MS sheet of profile 105 mm X 60 mm for door and window frames with one or more rebates including lock strike plate, shock absorber, 20 mm dia 60 mm long MS conduit for housing of a drop bolt,hinges, hold fasts/lugs etc, treating of internal surfaces of chowkhats with coal tar or black paint including hold fasts/lugs etc complete all as specified.

S&F Factory made solid PVC door frame (having density not less than 600 kg/cum) of size 50 mm x 47 mm made of 5 mm plain colour PVC sheet reinforced with mild steel square tube, complete all as specified in MES Schedule Part-I (2009),including making good jambs in CM (1:4) with finishes to match with existing, complete all as per specification & drawing.

S&F Factory made solid panel PVC door shutter 30 mm thick (having density not less than 600 kg/cum) consisting of frame made out of MS tubes for top & bottom rails, MS frame covered with heat moulded plain colour PVC ‘C’ channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail; paneling of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles & rails with suitable PVC sheet beading and jointed together with solvent cement, supply and fixing in the frame at site, complete all as per specification in MES Schedule Part-I (2009) & drawing.

S&F Factory made, 35mm thick, 2nd class hard wood (Hollock), plain framed, panelled shutters, any number of panels, panels shall be of 9 mm thick B.W.P. commercial ply or 12mm thick BWR grade veneered particle board medium density, wood particle board with commercial face veneers, size of members as specified in clause 8.24(a) of MES Schedule Part-I section-8 complete all as specified.

S&F Factory made 35 mm thick,2nd class hard wood (Hollock), glazed and skeleton shutters open rebated and prepared to receive glass/ gauge etc (without sash bars), edges of framing plain chamfered or rounded, fitted with cut and mitered beads for securing glass/gauge etc for doors, size of members as specified in clause 8.24 (a) of MES Schedule Part-I Section-8, complete all as specified.

S&F 300 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed, complete all as specified.

S&F extruded Aluminium handle, aluminium anodized, 150 mm long fabricated type and fixed with steel screws complete all as specified.

S&F Extruded Aluminium alloy barrel tower bolts, 200 mm long and fixed with steel screws complete all as specified.

S&F Extruded Aluminium alloy tower bolts, 150 mm long and fixed with steel screws complete all as specified.

S&F cold rolled mild steel, butt hinge, 100mm long, medium weight, fixed with steel screws or welded to steel frame where required complete all as specified.

S&F 100 mm butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21, complete all as specified.

S&F in repair, 300 mm mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified.

S&F Galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified.

S&F in repair, galvanised mild steel wire cloth 0.56mm nominal dia of wire and average width of aperture not more than 1.18mm and fixed with tinned tacks or galvanized wire staples, complete all as specified .

S&F Framed work such as grills, gratings, etc with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work, complete all as specified.

M&L for welding in running for thickness of metal to be welded n.exc 6mm, complete all as specified.

M&L Cement concrete (1:2:4) type B-1 (20 mm graded stone aggregate) as in bed blocks, benching,coping etc including form work,weathering, slightly rounded or chamfered complete all as specified.

M&L for Non skid Ceramic coloured (colour and shade as approved) tiles, any shape, 7mm to 8 mm thick area of each tile exc 0.06 sqm and not exc 0.11 sqm as in flooring, set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6), complete all as specified.

M&L for Non skid Ceramic coloured ( colour and shade as approved) tiles,any shape, 7mm to 8 mm thick area of each tile exc. 0.11 sqm and not exc 0.18 sqm as in flooring set and jointed in neat cement slurry and pointed in white cement with pigment to match the colour of tiles laid over & including 15 mm thick screed in cement mortar (1:6) laid over, complete all as specified.

M&L for Glazed ceramic tiles, coloured (colour & shade as approved), of size 300x200x7 mm thick on vertical surfaces such as in skirting/dado etc set and jointed in cement slurry and pointed in white cement with pigment to match the colour of tiles, laid over & including 10 mm thick backing coat in cement mortar (1:4), complete all as specified.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing as in flag post, floors and all other similar works & including 15 mm thick screed in cement mortar (1:6) laid over, complete all as specified.

M&L for Kota stone slabs, 20mm to 25mm thick, machine cut as in flooring of size not less than 0.25 Square metre each, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including screed bed of 15 mm thick in cement mortar (1:6) including rubbing, cutting and polishing (mirror type) complete all as specified.

S&F Kota stone slabs, 20 mm thick, machine cut as in shelf, skirting,steps,dado,pillars etc, set and jointed in cement slurry and pointed in cement mixed with pigment to match the shade of slab laid over & including rendering coat of 10 mm thick in cement mortar (1:4) including rubbing, cutting and polishing, complete all as specified.

S&F Galvanised steel water tubing, 20 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

S&F Galvanised steel water tubing, 15 mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors including cutting and making good, complete all as specified.

Re-Fixing only, steel water tubing, 15mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors complete all as specified.

Re-Fixing only, steel water tubing, 20mm bore and connections in new or old position using new fittings fixing to wall/ceiling or laid in floors, complete all as specified.

Fixing only in repair sinks kitchen or laboratory with plugs, washers and wastes including beding in cement mortar on to dwarf walls, or including fixing cantilever brackets and connecting union to waste pipe upto 0.5 sqm each, complete all as specified.

S&F in repair, waste coupling of PTMT half or full threaded (Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified.

S&F in repair 15 mm bore bib tap of, fancy type, chromium plated, screwed down, high pressure with crutch or butter fly handle, complete all as specified.

S&F in repair 15mm stop valve/angle cock, cast copper alloy with crutch or butterfly handle, screwed down screwed for iron pipe or for brass ferrule fancy type chromium plated with long shank and cup (concealed type), complete all as specified.

S&F in repair 15mm bore pillar tap fancy type, cast copper alloy, chromium plated, screwed down high pressure, with or without lettered ‘Hot’ or ‘Cold’ with long screwed shanks and fly-nuts, screwed for iron pipe, complete all as specified.

S&F in repair, 100mm Cast iron nahani trap, with grating including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4), complete all as specified.

M&L for 75mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement, complete all as specified.

S&F 32mm bore high density polyethylene (HDPE) pipes of pressure rating 6 kg/sq. cm, complete all as specified.

S&F in repairs wash hand basin, flat back 550mm x 400mm vitreous china (white) including PTMT waste coupling/fittings, 32 mm bore size, waste pipe, PVC, 32mm bore, angle iron/cast iron brackets of required size as directed & making good disturbed surfaces to match with the existing, complete all as specified.

S&F in repair Vitreous china white squatting pan orrissa pattern of size 580mm x 440mm with integral foot rests including necessary lime concrete and 100 mm bore cast iron ‘P’ & 'S' trap with 550 to 600 mm long neck for connecting WC to branch piece with cement joints, complete all as specified.

S&F Galvanised steel water tubing, 40mm bore, medium grade with all fittings and fixed to walls and ceilings or laid in floors/sunken floors as spout complete all as specified.

S&F in repairs PVC syphonic action type low level flushing cistern (white) of 10 liters capacity with inlet ball float valve, 32 mm PVC flush pipe and necessary fixing arrangements and connecting to water pipe, complete all as specified.

M&L in repair, 2nd class soft wood fillets, sectional area n.exc. 3 sqcm, rectangular in section, wrought finished, fixed with PVC rawl plug & steel screw complete all as specified.

M&L in repair, 2nd class soft wood fillets, sectional area exc 13 sqcm but n.exc.25 sqcm, rectangular in section, wrought finished, fixed with PVC rawl plug & steel screw complete all as specified.

S&F factory made PVC cup boards/shelfs/partition of required size consisting of panel of 18mm thick Celuka PVC ply and for supporting the hold of shelf/partition and shall provided 3 edge in size 18x18mm as per required length. The front side of the edge visible in front of the shelf/partition to be edge lipped by the 18mmx1mm thick PVC sheet using solvent cement etc, complete all as specified.

S&F Continuous (piano) hinges, mild steel bright finish or electro galvanised with flap (when open) 25 mm wide, fixed with steel screws complete all as specified.

S&F in repairs, 25mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished, complete all as specified.

S&F in repairs, magnet catchment of specified shape and size for cupboard selves in kitchen etc, complete all as specified.

S&F in repair 500 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs including fittings, complete all as specified.

Disconnecting existing tanks, 500 litres capacity rotational moulded setting aside (or lowering if required) for repairs, cleaning, etc. and hoisting if required reconnecting and re-fixing in position, complete all as specified.

S&F in repair, 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed, complete all as specified

S&F in repair 20mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball(Minimum weight 210 gm ), screwed for iron pipe or brass ferrule , complete all as specified.

S&F in repairs, 110 mm bore PVC (SWR) pipes single socketed, in any length with rubber ring joints, laid in trenches or in floors including distance pieces and including stack clamps with nuts & bolts, complete all as specified.

S&F in repairs 110 mm bore PVC (SWR) bends/shoe and provided with access door any radius fixed to walls including distance pieces and stack clamps ,including making good around complete all as specified.

S&F in repairs 75 mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

All as per item 106, but expect pipes, complete all as specified.

S&F 75 mm bore, cast iron bend (any radius), diminishing pieces or tapers (larger bore measured) with oval access cement joints, complete all as specified.

S&F 100 mm dia cast iron soil, waste and vent pipe, sand cast, in any length with or without ears with cement joints fixed to walls with and including suitable clamps, complete all as specified.

All as per item 109, but expect pipes, complete all as specified.

S&F in repair 100 mm bore, cast iron bend (any radius), diminishing pieces or tapers (larger bore measured) with cement joints complete all as specified.

M & L tubular Towel Rail 60cm long 'D' type between flanges of aluminium anodized 20mm dia fixed to walls, complete all as specified.

M&L for applying bond coat of epoxy bonding agent & cement 1:1 ratio for bonding old and new concrete on damaged surfaces applying polymer modified mortar in CM 1:3 including mixing of polymer latex additive upto 60 mm thicknes (Chajja's fins,border etc) Note :- (i) Quantity of polymer to be used @ 15 % by weight of cement. (ii) Use of electrical mixer to get homogeneous dough on bond coat surfaces. (iii) To achieve required thickness repeat this step after 24 hrs to as required. (iv) Keep the surface moist using water fog for 5 to 7 days etc complete all as specified and as directed. (v) Rate shall be inclusive of all necessary scafolding for building hieght up to 24 meter complete all as specified and directed by Engineer-in-Charge.

S&F in repair Mild steel curtain rod 20mm dia PVC powder coated with fixing side brackets, end cups, rings @ 10 Nos per RM and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified.

M&L Preparation of new wooden or wood based surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer, complete all as specified.

M&L Preparation of old treated wooden surfaces of any description, over 10cm width or girth and applying one coats of synthetic enamel paint complete all as specified.

M&L Preparation of new steel surfaces of any description, over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide, complete all as specified.

M&L Preparation of old treated steel surfaces of any description, over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified.

Taking down carefully existing alumimium point wiring for light/fan/socket out let points complete with fitting and fixtures, battens, wire etc and making good the disturbed surfaces of walls and ceilings, complete all as specified.

S&F Point wiring complete with 1100 volts grade PVC FRLS insulated unsheathed cable of copper conductor, multi stranded of size 1.5 Sqmm, single core, drawn through existing rigid non-metalic PVC concealed conduit, medium grade of suitable size with all accessories such as bends, reducers, spacers, saddles, junction boxes, bakelite sheets, sizes for mounting switch/sockets, fan regulators etc complete with and including continuous earth wire of size 1.5 Sqmm, single core, PVC FRLS copper conductor, insulated, unsheathed,stranded (Green colour) connected to common earth dolly complete all as specified for following :- (a) One light/fan point/bell controlled by one single pole one way switch.

(b) One 3 pin 5 Amp socket outlet point controlled by one switch on same board.

(c) One 3 pin 5 Amp socket outlet point controlled by one switch on Independent board .

All as per item 122 above but one switch socket outlet multi purpose, 3pin, 15 Amps, point to be controlled by one switch and wiring with 2.5 Sqmm PVC FRLS cable,insulated, stranded, unsheathed copper conductor on Independent board with continuous earth wire of size 2.5 sqmm , PVC copper conductor, insulated, unsheathed, stranded, complete all as specified

S&F Switch, piano, flush type, single pole one way, 5 Amps, ISI marked, complete all as specified.

S&F Switch piano flush button type 15 Amps, single pole, one way, ISI marked, complete all as specified.

S&F Socket outlet,2 in 1, 5 pin ,5 Amp, piano flush type, ISI marked, complete all as specified.

S&F Socket outlet 2 in 1, 6 pin,5 Amp and 15 Amp, piano flush type, ISI marked, complete all as specified.

S&F, Bell push, flush type, 5 amp complete all as specified.

S&F Ceiling rose, surface type, backelite 65mmx50mm, 3 terminals, complete all as specified.

S&F Lamp holder, PVC/polycarbonate, suitable for bracket/batten fittings, including LED lamp 10 watts, complete all as specified.

S&F bell Ding Dong AC 230 volts, single pole, complete all as specified.

S&F in repairs stepped type electronic fan regulator for ceiling fan 1200/1400mm size,230 volts,6 Amps, complete all as specified.

S&F in repair LED light fittings, single tube 1x18 watt decorative ultra slim linear LED lighting fixture with extruded polycarbonate, environment friendly fixed to wall/ceiling etc,connector block etc complete with copper flexible wire of size 23/0.0076 twin core from ceiling rose to connector complete all as specified.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet, powder coated, concealed in wall, TPN DB with 200 Amps rated bus bar, 6 way, 415 volts, vertical type, dust and vermin proof, suitable for incorporation of MCBs duly concealled in wall, factory made, including making good distrubbed surfaces with matching colour, complete all as specified.

S&F in repair Factory made sheet metal enclosures double door type made out of CRCA 1.2 mm thick M.S sheet,powder coated, SPN DB with 200 Amps rated bus bar, 8 way, FP-42 protection surface mounting, 240 volts, dust and vermin proof, suitable for incorporation of MCCBs duly concealled in wall, factory made,including making good distrubbed surfaces with matching colour, complete all as specified.

S&F of MCCB Thermal based release adjustable type 4 pole 63 Amps 50 HZ 415 Volts with rupturing capacity 16 KA including testing, complete all as specified and as directed.

S&F in repairs MCB, single pole, 240 Volt, 6 to 32 Amps, 10 KA complete all as specified.

S&F in repairs MCB, SPN, 32 Amps, 240 volts duly ISI marked, complete all as specified.

S&F in repairs for sub main wiring with two single core PVC insulated unsheathed stranded copper conductor cable FRLS 2x6 Sqmm single core 650/1100 V, drawn through & including rigid PVC non metallic concealed conduit 25 mm dia including continuous earth wire of size 1x6 sqmm, PVC insulated and unsheathed cable copper stranded conductor (green colour) complete all as specified. NOTE:-Two runs of cable, 1 run of earth wire & one run of PVC conduit shall be measured as one length.

M& L Earthing complete, all as shown on electrical plate No 3 of MES schedule part-I , as in repairs and as specified including the following :-(i) Galvanised steel earth plate of size 60cmsx60cmsx6mm thick burried directly in ground vertically to a depth not less than 2.25 metre below ground level with top edge of earth plate at a depth not less than 1.50 metre below normal ground level.(ii) Earth plate surrounded by and packed with char-coal and common salt in alternative layers (n.exc 15cms each layer).(iii) 4 mm dia (8 SWG) G.I earth wire from earth plate to main switch board including necessary GI bolts, nuts check nuts, washers, thimbles etc.(iv) 15 mm bore light grade, GI pipe for protection to earth-strip.(v) 20mm bore, medium grade GI pipe for watering including GI funnel and wire mesh. Pipe shall be provided vertically upto top level of earth pit and then taken horizontally to the earth pit. (vi) 50mm thick pre-cast cover of cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate and MS angle iron 25x25x3mm frame including two coats of painting over a coat of red oxide to exposed steel surfaces.(vii) Excavation in soft/loose soil, returning filling & removal of surplus soil to a distance upto 50 metre as directed.

Supply & Fixing LED Bldg security light 30 watts lens type, pressure die cast aluminium housing, heat resistance toughened glass with frame, IP 66 protection with bracket (for housing street light fittings) made of GI pipe 40 mm dia light grade 1.0 mtrs long duly cutted and welded at an angle of 120 degree and fixed to wall with suitable MS clamps - 02 Nos with 16 mm dia bolts, nuts, and washers, complete all as specified and directed.

S&F as in repairs XLPE insulated, armoured,1100 volts grade, heavy duty cable of size 25 Sqmm nominal cross section, 4 core, flat or circular, PVC FRLS insulated aluminium conductor, served with inner sheathing of galvanized steel wire or tape and over-all PVC FRLS sheathed in service connections, laid in trenches, duct, through pipe, in floor, on pole including jointing and testing, complete all as specified .

M&L Dry and clean fine sand for cable cushioning to underground cable protection, complete all as specified. (Excavation and earth work measured separately). Note- Punned down thickness shall be measured.

S&F in repair Cover to underground cable with one layer of bricks using sub class ‘B’ bricks (old size) laid flat across the cable complete all as specified. (Excavation and earth work measured separately).

S&F Mild steel galvanised pipe, light grade, 40 mm nominal bore for passing of cable, fixed to poles/laid under floor/road crossing/walls complete with and including clamps socket & elbow etc complete all as specified.

R.S.ENTERPRISES

M/s Vishant Construction Co

M/s Sanjiv Kumar

Sethi and Company

Guru Kirpa Trading Company

M/S Yashpaul Gulati

M/s Bansi Lal