Construction of Government Degree College in Village Jarcha Tehsil Dadri District Gautam Budh Nagar

Clearing jungle including uprooting of rank vegetation , grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distanceof 50 moutside the periphery of the area cleared.

Earth work in Excavation in trenches for foundations pipes cable etc. in ordinary soil (Loan clay or sand) including lift upto 1.5 m. lead upto 50m and dressing of sides and rammings of bottom and disposal of surplus excavated earth as directed by the Engineer i/c within a lead of 30m.00.00 TO 1.50 MTR. DEPTH

1.50 TO 3.0 MTR. DEPTH

Providing and laying cement concrete in 1:4:8 (1 Cement : 4 Coarse sand : 8 graded Stone aggregate 40mm nominal size) and curing complete. Including cost of form work. In foundation and floors. As in item above but in the proportion 8:4:1

Providing and laying in position ready mixed or site batcheddesign mix cement concrete for reinforced cement concrete work;using coarse aggregate and fine aggregate derived from naturalsources, Portland Pozzolana / Ordinary Portland /Portland Slagcement, admixtures in recommended proportions as per IS: 9103to accelerate / retard setting of concrete, to improve durabilityand workability without impairing strength; including pumpingof concrete to site of laying, curing, carriage for all leads; butexcluding the cost of centering, shuttering, finishing andreinforcement as per direction of the engineer-in-charge; for thefollowing grades of concrete.Note: Extra cement up to 10% of the minimum specified cementcontent in design mix shall be payable separately. In case thecement content in design mix is more than 1.10 times of thespecified minimum cement content, the contractor shall havediscretion to either re-design the mix or bear the cost of extracement.All works upto plinth level Concrete of M25 grade with minimum cement content of 330 kg /cumFoundation

Plinth beam

All works above plinth level upto floor V level Concrete of M25 grade with minimum cement content of 330 kg /cumLintel Band

Slab Beam

Chajja Slab

Column

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, for mass concrete.

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Centering and shuttering including strutting, propping etc. and removal of form for Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more.(TMT Bars) Fe-500

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:4 (1 cement : 4 coarse sand)

Brick work with common burnt clay F.P.S. (non modular) bricks of classdesignation 7.5 in superstructure above plinth level up to floor V level inall shapes and sizes in :

Supplying and filling in plinth with sand under floors, including watering, ramming, consolidating and dressing complete.

Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floorV level

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

20mm th. Bearing plaster in 1:4 in two coats backing cost 17mm and finishing coat 3mm thick of neat cement and marble dust in ratio 5:1 on rough side of single or half brick interior plastering upto floor two level including internal rounded angeles. upto floor five level

Providing and laying damp-proof course 40mm thick with cementconcrete 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from naturalsources : 4 graded stone aggregate 12.5mm nominal size derived fromnatural sources)

12 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 6 coarse sand)

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 6 coarse sand)

Providing & applying a coat of residual petroleum bitumen of grade ofVG-10 of approved quality using 1.7kg per square metre on damp proofcourse after cleaning the surface with brushes and finally with apieceof cloth lightly soaked in kerosene oil.

15 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 6 coarse sand)

12 mm cement plaster on rough side of single or half brick wall of mix: 1:4 (1 cement: 6 coarse sand)

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying :(a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours.(b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours.(The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) upto floor five level

6mm thick plastering on ceilings and soffits of stairs upto floor two level instead of plastering in walls in proportion of 1 : 3 cement & sand mortar upto floor five level

Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone of size 12.5mm nominal size) laid in one layer finished with floating coat of neat cement (25mm thick floor)

Chequered terrazo tiles 22 mm thick with graded marble chips of sizeup to 6 mm in floors, jointed with neat cement slurry mixed with pigmentto match the shade of the tiles, including rubbing and polishing complete,on 20 mm thick bed of cement mortar 1:4 (1 cement :4 coarse sand) :

Providing and fixing glass strips in joints of terrazo/ cement concrete floors. (a) 40 mm wide and 4 mm thick

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diameter holes and plugging with cement mortar 1 :2 (1 cement : 2 Coarse sand) to match the existing floor:

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture STEEL

Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture wood

Extra for providing and placing in position 2 Nos 6mm dia. M.S. bars at every third course of half brick masonry. upto floor five level

2cm (3/4") thick cement plaster in dado of skirting in 1:3 consisting of one part of cement and two parts of approved coarse sand laid in panels, finished with 3mm 1/8") flooating coat of neat cement or cement and marble dust in ratio of 5:1 including supply of all materials, labour and tools and plants etc. required for proper completion of the work.

Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in- Charge.

Providing and laying matt finished vitrified tile of size 100x100x16mm having water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in out door floors such as footpath, court yard multi models etc., laid on 20mm thick base of cement mortar 1:4 (1cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as direction of Engineer-in- Charge.

P/L integral cement based water proofing treatment BIRCK COBA including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operation: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge Over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment (b) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge to required slope and treating similarly th adjoinin walls upto 300mm height including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth With average thickness of 120 mm and minimum thickness at khurra as 65mm.

Providing and fixing angle iron frames for doors, windows and ventilator so f mild steel angle sections of size 35x35x5 mm, joints mitred andwelded by angle iron 35x35x5 mm or 35x 5 mm flat pieces to the existingT-iron frame or to the wall with dash fastener, including fixing of necessary butt hinges and screws and applying a priming coat of approved steelprimer, all complete as per the direction of Engineer-In-charge

Providing and fixing M.S. tubular frames for doors, windows, ventilators and cupboard with rectangular/L-Type sections, made of 2.00 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary but hinges and screws and applying a priming coat of approved steel primer fixing with 15x3mm lugs 10cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6(1 Cement : 3 Coarse Sand : 6 graded stone aggregate 20mm nominal size) upto floor five level

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes 6kg/cm2 conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion (i) Single socketed pipes. 110 mm diameter upto floor five level

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, including priming coat of approved steel primer, but excluding the cost of other,fittings, complete all as per approved design, (sectional weight of only steel members shall be measured for payment).Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) Z Section

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick(a) Single leaf

Providing and fixing glazing in aluminium door, window, ventilator shuttersand partitions etc. with EPDM rubber / neoprene gasket etc. complete asper the architectural drawings and the directions of engineer-in-charge With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm

P/F 30mm thick plain factory made panel PVC doors shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm*19mm for styles and 15*15 mm for top & bottom rails. M.S. frame shall have a coat of steel primesrs of covered with 5 mm tick heat moulded PVC C channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45 degree angle off both sides forming sytles and 5 mm thick, 95 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both sides of the panel. 10 mm (5mm*2) thick, 20 mm wide cross P/v/c sheet be provided as gap insert for top rail & bottom rail. Peneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame selded/ sealed to the styles & rails with 7 mm (5 mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20mm width is to be stuck on the interior side of the C channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manfacturer specification & drawing. upto floor five level

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Providing and fixing oxidised M.S. casement stays (straight peg type) with necessary screws etc. complete.300 mm weighing not less than 200 gms upto floor five level

Prociding and fixing to the inlet mouth of rain water pipe PTMT (an Engineering Thermoplastic) grating square (Slit) 150 mm square with a height of 8 mm and weighting not less than 100 gms.size 150mm

Providing and fixing S.S. wire gauge using average width of aperture 1.4mm in both directions with wire of dia 0.63mm and glazed shutters for doors, fixing with butt hinges of required size with necessary screws, (including panelling ) including cost of S.S. door fitting all complete as per direction of Engineer-in-charge. Second class teak wood 35 mm thick shutters

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315 , having brand logo embossed on the body/ plate with double spring mechanism and door weight upto 125 kg, for doors including cost of cutting floors ,embeding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete.

Providing and fixing in position collapsible steel shutters with veritical channels 20x10x2mm and braced with flat iron diagonals 20x50mm size, with top and bottam rail of T-iron 40x40x6mm, with 40mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. agnels 40x40x6mm for diagonal braces upto floor five level

Distempering with oil bound washable distemper of approved brandand manufacture to give an even shade : New work (two or more coats) over and including water thinnable priming coat with cement primer

S/F of cinder for sunken protion of toilets and kitchen as per directions of E/I upto floor five level

Supply and filling of good earth upto 5 km including supply of earth filling, raming in 20cm layer, watering , cost of royalties etc., complete in all respect as per direction given Engineer-in-charge.

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete. upto floor five level

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge, Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye-rosy pink or equivalent. upto floor five level

Providing and Laying kota stone flooring over 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid over jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete. 25 MM THK

Providing and fixing nickel plated M.S. pipe curtain rods with nickel plated brackets : 25mm dia

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqmover and including priming coat of exterior primer applied@ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness1 mm, of approved brand and manufacturer, over the plastered wallsurface to prepare the surface even and smooth complete.

Providing and fixing ISI marked oxdised M.S. Sliding door bolts with nuts and screws etc complete. 300x16mm

Providing and fixing ISI marked oxdised M.S.Tower bolts black finish (Barrel type) with necessary screws etc complete.250x10mm

Providing and fixing ISI marked oxdised M.S.handles conforming to IS:4992 with necessary screws etc complete.100mm

PLUMBING Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredWhite Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Same as above but for European type W.C. pan with white plastic seat and lid.Make- Cera,Hindware.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tappillar tap.

Providing and fixing white vitreous china laboratory sink with C.I.brackets, C.P. brass chain with rubber plug, 40 mm C.P brass wasteand 40mm C.P. brass trap with necessary C.P. brass unions complete,including painting of fittings and brackets, cutting and making goodthe wall wherever required : Size 600x450x200 mm

\Providing and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings complete.) 32mm dia

b) 40mm dia

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm and 340x410x265 mm sizes respectively with automatic flushing cistern with standard flush pipe and C.P. brass spreaders with brass unions and G.I clamps complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever requiredRange of two urinal basins with 5 litre white P.V.C. automatic flushing cistern

Providing and fixing stone slab table rubbed, edges rounded and polished of size 75x50cm deep and 1.8cm thick fixed in Urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1cement: 2coarse sand: 4graded stone aggregate 6mm nominal size) as per direction of Engineer-in-charge and finished smooth.Granite Stone of approved shade

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing 8 mm dia C.P./S.S. Jet with flexible tube upto 1 meter long with S.S. triangular plate for Eureopean type W.C. of quality and make as approved by engineer-in-charge.15mm nominal bore

Providing and fixing CP Brass 32 mm size Bottal Trap of approved quality & make and as per the direction of Enginer-in-charge.

Providing and Fixing C.P. brass Ablution health faucet assembly with 1.0 m long braided PVC hose with mounting bracket fixed on wall complete.[FOR EWC]-Make-JAQUAR ALD-565

Providing and fixing C.P. brass Two-way angle valve for EWC points & for fixing Ablution Health Fauct of approved quality conforming to IS:8931. 15 mm nominal bore-ESSCO SQT 526AKN

Providing & fixing 60x2cm. C.P. brass towelrail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw. ESSCO AEC-1181

Supplying & Fixing of CP soap tray fixed to the wall with PVC rubber plug with CP brass screws- Make-ESSCO AEC-1131

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge) 150 mm nominal dia Pipes

b) 100 mm nominal dia Pipes

c) 80 mm nominal dia Pipes

Providing & fixing M.S. holder bat clamps of approved design to sand cast iron/centrifugally cast (Spun) iron S & S pipe embeded in & including cement concrete blocks 10x10x10cm. of 1:2:4 mix (1 cement : 2 coarse : 4 graded stone aggregate 20mm nominal size). Including cost of cutting holes & making good the walls etc. for 100mm dia pipe.

b) for 75mm dia pipe.

Providing & fixing cast iron trap of self cleansing design with or without ventarm complete, including cost of cutting & making good the walls & floors. 100mm inlet & 75mm outlet.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes. 110mm diameter

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. 25 mm nominal dia Pipes

b) 32 mm nominal dia Pipes

b) 40 mm nominal dia Pipes

c) 50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c ixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. 16mm dia nominal bore

b) 20mm dia nominal bore

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.15mm nominal bore

Providing & fixing CP brass bib cock of approved quality conforming to IS 8931 ) 15mm nominal bore

Providing & fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 8931 15mm nominal bore

Providing and fixing gun metal gate valve with wheel of approved quality. 25mm dia nominal bore

c) 32mm dia nominal bore

d) 50mm dia nominal bore

aProviding and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete) 20 mm nominal bore

b) 25 mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank of approved brand and manufacture with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank Circular Tank

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m. Pipes 80mm to 300mm diameter.

Providing and laying non-pressure NP2 class (light duty) R.C.C.pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete :) 100mm diameter

b) 150mm diameter

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design. 100mm diameter

b) 150mm diameter

Constructing brick masonry manhole in cement mortar 1:4 (1 cement :4 coarse sand) RCC top slab with 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate 20mm nominal size), foundation concrete 1:4:8 mix (1 cement :4 coarse sand :8 graded stone aggregate 40mm nominal size) inside plastering 12mm thick with cement mortar 1:3 (1 cement :3 coarse sand) finished with floating coat fo neat cement and making channels in cement concrete 1:2:4 (1 cement :2 coarse sand :4 graded stone aggregate 20mm nminal size) finished with a floating coat of neat cement complete as per standard design (i)Inside size 90x80cms and 45cms deep including CI cover with frame (light duty) 455x610mm internal diamensions total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15kg).With FPS bricks of class designation 75 For Sewer Line

Extra for depth of man hole size 90x80 cm

Providing orange colour safety foot rest of minimum 6mm thick plastic encapsulated as per IS : 10910 on 12mm dia steel bar conforming to IS: 1786 having minimum cross section as 23 mm x25mm and over all minimum length 263mm and width as 165mm with minimum 112mm space between protruded legs having 2mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufactures's permanent identification mark to be visible even after fixing, including fixing in manholes with 30x20x15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) complete as per design.

Providing & fixing G.I. pipes complete with G.I. fittings including tenching and refilling etc. (external work)50mm nominal bore.

Providing and fixing gate valve (with cap complete with bolts, nuts, rubber insertion etc.50mm

Constructing masonry Chamber 60x60x75 cm, inside with 75 class designation brick work in cement mortar 1:4 (1 cement :4 coarse sand ) for sluice valve, with C.I. surface box 100mm top diameter, 160mm bottom diameter and 180mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) necessary excavation foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick finished with a floating coat of neat cement complete as per standard design :With F.P.S. bricks

Making connection of G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete :50 to 80 mm dia nominal bore

ELECTRICAL Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Supplying and fixing following modular switch/ socket on the existing modular plate & switch box including connections but excluding modular plate etc. as required.5/6 A switch

3 pin 5/6 A socket outlet

Bell push

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate asrequired.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. (Mirror Light + Wall Fan + Ex. Fan)

Supplying and fixing suitable size GI box with modular plate andcover in front on surface or in recess, including providing andfixing 3 pin 5/6 A modular socket outlet and 5/6 A modular switch, connections etc. as required.

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch, connections etc. as required.

Supplying & fixing suitable size GI box wih modular plate and cover in front on surface or in recess including providing and fixing 25 A modular socket outlet and 25 A modular SP MCB, "C" curve including connections, painting etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

4 X 6 sq. mm + 2 X 6 sq. mm earth wire

4 X 10 sq. mm + 2 X 6 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Providing and fixing plain 16/0.20mm (0.50sqmm) twin flat flexible, FRLS PVC insulated, copper conductor cable, in PVC sleeve of suitable size on the floor/ wall, or side of the table/ door etc. as required.

Supplying and fixing following way, horizontal type three pole and neutral, sheet steel, MCB distribution board, 415 V, on surface/ recess, complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator)6 way (4 + 18), Double door

Supplying and fixing following rating, four pole, 415 V, isolator in the existing MCB DB complete with connections, testing and commissioning etc. as required.40 A

Supplying and fixing 5 A to 32 A rating, 240/415 V, 10 kA, "C" curve, miniature circuit breaker suitable for inductive load of following poles in the existing MCB DB complete with connections, testing and commissioning etc. as required.Single pole

Supplying and fixing single pole blanking plate in the existing MCB DB complete etc. as required.

Supplying and fixing 20 A, 240 V, SPN Industrial type socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20 A "C" curve, SP, MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 30 A, 415 V, TPN Industrial type socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 A "C" curve, TPMCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket out let and complete with connections, testing and commissioning etc. as required.

Supply of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 66 and above Protection . complete in all respect.

Supply of LED Tube Light batten fitting suitable for up to 1 X 12 watt LED tube Mirror light on surface complete in all respect.

Supply of round 15 Watt LED Down Lighter with heat sink, diffuser/ Reflector and driver set complete in all respect.

Supply of LED Tube Light with batten suitable for up to 1 X 20 watt LED tube light fitting including tube on Surface complete in all respect

Supply of 300 mm dia Heavy Duty Exhaust Fan

Supply of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 45 watt. Confirming to IP 66 protection complete in all respect.

Supply, Installation, Testing and Commissioning of 1200 mm sweep, BEE 5 star rated, ceiling fan with Brush Less Direct Current (BLDC) Motor, class of insulation: B, 3 nos. blades, 30 cm long down rod, 2 nos. canopies, shackle kit, safety rope, copper winding, Power Factor not less than 0.9, Service Value (CM/M/W) minimum 6.00, Air delivery minimum 210 Cum/Min , 350 RPM (tolerance as per IS : 374-2019), THD less than 10%, remote or electronic regulator unit for speed control and all remaining accessories including safety pin, nut bolts, washers, temperature rise=75 degree C (max.), insulation resistance more than 2 mega ohm, suitable for 230 V, 50 Hz, single phase AC Supply, earthing etc. complete as required.

Supplying and fixing of 32 mm dia X 2.00 metres long G.I. pipe (medium class) bracket for mounting of fluorescent / HPMV / HPSV street light fitting on pole including bending the pipe to the required shape, 2 nos 40 mm X 3 mm flat iron clamps with nuts,bolts and washer, painting the flat iron with primer and finish

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Supplying and fixing call bell/ buzzer suitable for single phase, 230 V, complete as required.

Installation, testing and commissioning of pre-wired,fluorescent fitting / compact fluorescent fitting of all types,complete with all accessories and tube/lamp etc. directly onceiling/ wall, including connections with 1.5 sq. mm FRLS PVCinsulated, copper conductor, single core cable and earthing etc.as required.

Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (upto 30 cm) with 1.5 sq. mm FRLS PVC insulated, copper conductor, single core cable, including providing and fixing phenolic laminated sheet cover on the fan box etc. as required.

Installation of exhaust fan in the existing opening, including making good the damage, connection, testing, commissioning etc. as required.Upto 450 mm sweep

Earthing with G.I. earth plate 600 mm X 600 mm X 6 mm thick including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe of 2.7 metre long etc. with charcoal/ coke and salt as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Supply of aluminium conductor PVC / XLPE insulated armoured served sheathed cables 1100 Volts grade.16 sqmm 4 core

35 sqmm 3 1/2 core

120 sqmm 3 1/2 core

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Laying and fixing of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size on wall surface as required.Upto 35 sq. mm (Clampped with MS flat Clamp)

Above 95 sq. mm and upto 185 sq. mm (Clampped with MS flat Clamp)

Supplying and making end termination with brass compression gland and aluminium lugs for following size of PVC insulated and PVC sheathed / XLPE aluminium conductor cable of 1.1 KV grade as required.4 X 16 sq. mm (28mm)

3½ X 35 sq. mm (32mm)

3½ X 120 sq. mm (45mm)

Providing, laying and fixing following dia G.I. pipe (medium class) in ground complete with G.I. fittings including trenching (75 cm deep)and re-filling etc as required100 mm dia

Design, fabrication, assembly, wiring and supply of front operated dead front cubicle type compartmentalised as per Form 3B, rear access free standing, dust and vermin proof (IP 42 ingress protection) main switchboards suitable for use at 415 volts, 3 phase 4 wire 50 Hertz system suitable for a symmetrical fault level of 55 kA at 415 volts, fabricated from 2 mm thick CRCA MS sheets with hinged, gasketted (metal based neoprene) and lockable doors having structural reinforcement with suitable angle/channel/T/flat sections including 3 mm thick gland plates on top and bottom and including lifting hooks with sleeved TPN Aluminum Bus bars and GI earth strip of required size with 2 nos earthing terminals and including powder coated paint finish of approved shade (RAL 7032) over metal surface cleaned and treated with seven tank process complete with interconnections etc as per specifications, as required and as below. This main panel must be extendable for future requirement in such a manner not to disrupt ongoing services at the point of use during extension. All LT Panel shall conform to latest IS/IEC -61439 code. All Panel shall be complete with power & control wiring, danger & inscription plate, Lifting hooks etc.Incomer 250 Ampere 4 P MCCB - 2 No. Metering 0-160 Ampere Ammeter 0-500 V Voltmeter Bus Bar 250 Amp 4Pole Bus Bar with Color Codded Sleeves Outgoing 100Amp FP MCCB - 1 No. 60Amp FP MCB- 3Nos 63Amp FP MCB- 3Nos

Sub Panel

FIRE FIGHTING Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required:200mm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.150mm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.100mm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.80mm

Providing laying, testing & commissioning of 'C' class heavy duty MS Pipe conforming to IS 1239/3589 i/c fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. in ground including welding, excavation & providing cement concrete blocks as supports, anticorrosive treatment with coaltar/asphalt tape as per IS 10221, refilling the trench etc. of following sizes complete as required.25 mm

SITC of C.I double flanged Butterfly Valve complete with nuts, bolts & washers etc. conforming IS 780.Complete in all respect (Make:- Kalpana / AARKO/SIR) 200 mm dia

SITC of C.I double flanged Butterfly Valve complete with nuts, bolts & washers etc. conforming IS 780.Complete in all respect (Make:- Kalpana/AARKO/SIR) 150mm dia

SITC of C.I double flanged Butterfly Valve complete with nuts, bolts & washers etc. conforming IS 780.Complete in all respect (Make:- Kalpana/AARKO/SIR) 100 mm dia

SITC of C.I double flanged Butterfly Valve complete with nuts, bolts & washers etc. conforming IS 780.Complete in all respect (Make:- Kalpana/AARKO/SIR) 80 mm dia

SITC of cast iron double flanged Non Return Valve complete with nuts, bolts and washers conforming to IS 5312.Complete in all respect (Make:- Kalpana/AARKO/SIR/Kartar) 150mm dia

SITC of cast iron double flanged Non Return Valve complete with nuts, bolts and washers conforming to IS 5312.Complete in all respect (Make:- Kalpana/AARKO/SIR/Kartar) 100mm dia

Supplying and fixing first-aid Hose Reel with MSconstruction spray painted in post office red,conforming to IS 884 complete with the following asrequired.20 mm nominal internal dia water hose thermoplastic(Textile reinforced) type -2 as per IS: 1258520 mm nominal internal dia gun metal globe valve &nozzle.Drum and brackets for fixing the equipmets on wall.Connections from riser with 25 mm dia stop gun metalvalve & M.S. Pipe and socket. (Make:Safeguard/Lifeguard/Firex/Fire matic New Age.)

SITC of Air Cushion Tank assembly 200 mm dia. 1.5m long with Air Release Valve pressure gauge & accessories.Complete in all respect

S/F of GM Ball Valve 25 mm dia Complete in all respect

Providing / Fixing of Fire Hose cabinet (intarnal+extarnal Use) box made out of 18 gauge MS sheet including two coats of post office red paint over one coat of primer with 4 mm, thick glass door in front painted "FIRE" in red luminous paint. The size of the box should be 750 mm X 600 mm X 250 mm size capable of accommodating a pair of hose with coupling and nozzle. The box should be floor mounted type with railway coach lock arrangement and lever for opening the door after breaking the glass complete.

SITC of RRL Hose 63 mm dia x 15 m long complete with GM/SS coupling conforming to IS: 636.Complete in all respect (Make:- Safeguard/New Age/Lifeguard/Tulsi/primear)

SITC of GM/SS Branch Pipe & Nozzle IS: 903.Complete in all respect (Make:- Safeguard/Lifeguard/New Age)

SITC of Terrace Pump 450 LPM 7.5 HP.Complete in all respect (Kirlosker/other standard make)

SITC of Automatic panel of terrace pump Suitable for 5 HP Terrace Pump.

Supplying and fixing air vessel made of 250 mm dia, 8mm thick MS sheet, 1200 mm in height with air releasevalve on top nd flanged connection to riser, drainarrangement with 25 mm dia gun metal wheel valvewith required accessories, pressure gauge and paintingwith synthetic enamel paint of approved shade as required

SITC of pressure Gauge Complete in all respect

Supplying fixing of Cast iron body 63 mm dia male instantaneous intel coupling with housing cabinet (500X400X400 for 2 way and 600X400 for 4 way) cap and chain for fire brigade correction conforming to IS:904 and making connection with fire fighting pipe or underground water tank completing the work in all respect as per the directions of the Engineer-in-charge.

Supplying and fixing of Fire man axe

Supplying and fixing of Pressure Switch

Supply & fixing of ISI mark P.V.C. water tank (I,e. syntex or equvilant) with complete fitting and making base plate form

SITC of Single headed Hydrant comprising of 80 mm dia. Flanged bend 63 mm dia. GM/SS oblique pattern landing valve complete with blank and Cap.Complete in all respect (Make:- Safeguard/New Age/Lifeguard/G tech)

SITC of GM Fire brigade 4 way Inlet connection.Complete in all respect

SITC of C.l double flanged Foot Valve complete with nuts, bolts & washers etc. conforming IS 780.Complete in all respect (Make:- kalpana/AARKO/SIR) 150mm dia

SITC of Hose Box of 18 SWG M.S Sheet with glass fronted door to accommodate 2 nos. RRL Hose & 1 nos. GM/SS Branch Pipe with nozzel (External).Complete in all respect

Supply of ABC type Fire Extinguisher 4 kg Capacity. Make:- Sfeguard/Falcon/Fire matic/Cease fire

Supply & fixing of Co2 type Fire Extinguisher 4.5 kg Capacity. (Make:Sateguard/Firematic/Falcon/omex/Cease fire)

Supply & fixing of Fire Bucket 4 + Stand Complete in all respect

S/F of MS suport for pipe fitted with anchor bolt including painting.Complete in all respect

Supplying, installation, testing & commissioning of addressable manual call point complete as required.

Supplying, installation, testing & commissioning of addressable horn cum strobe complete as required.

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed steel conduit as required. 2X1.5 sq. mm + 1 X 1.5 sq. mm earth wire

Supplying, installation, testing & commissioning of response indicator on surface/recessed MS Box having two LED, metallic cover complete with all connections etc as required.

Supplying, installation, testing & commissioning of intelligent analog addressable photothermal detector complete with mounting base complete as required.

Supplying, installation, testing & commissioning of intelligent addressable thermal detector with rate of rise cum fixed tempreature thermistor complete with base as required.

Supplying, installation, testing & commissioning of repeater panel wih 320 character/ Touch screen LCD display with inbuilt reset, acknowledge and silence switches complete as required.

Supplying and drawing of cable Fire Retardant PVC insulated copper conductor cable in the existing surface / recessed steel conduit of following pairs, cores and size including connections and interconnections etc. as required. speaker cable Two pair, 2-core, 1.5 sqmm

Supply & laying of aluminum conductor PVC Insulated armored served sheathed cables 1100 Volts grade at a depth of below ground level over a cushion of 75 mm. below ground level over a cushion of 75 mm. thick sand all round and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. complete in all respect (Size 70 sq.mm.,3.5 core)

S/F Of 400 amp,415 v,heavy duty ,double break,HRC fuse type metal clad TPN ,complete with HRC Fuse etc.on angle iron frame complete in all respect

S/F of surface/flush mounting 6 way TPN DB without MCB with additional metal door complete in all respect Cat A

S/F of 63 Amp 4 pole MCB. complete in all respect Cat A

S/F of (6 A - 32A) SP MCB complete in all respect Cat A

BOUNDARY WALL Excavation in foundation in ordinary soil (Loam, Clay or Sand) Including lift upto 1.50 m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer In-charge upto a distance of 30m from the foundation trenches.

Providing and laying cement concrete in 1:4:8(1 Cement : 4 Coarce sand : 8graded stone aggregate 40 mm nominal size) and curing complete, Including cost of form work. in Foundation and floors. but in 1:4:8 in coarse sand

Reinforced cement concrete work in beams, suspended floors, roofs balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, including the cost of centering, shuttering, finishing and excluding reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand: 3 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers.

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, including cost of centering, shuttering, finishing and excluding reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

RCC Work Providing and laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and excluding reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. (TMT Bars) Fe-500

Class -150 brick work in 1:4 cement and coarse sand of 2.25 fineness modulus mortar in super-structure above plinth level up to floor two level ( up to two storeys ) including necessary cutting and moulding of brick work as required and also including honey combed brick work in thickness of wall more than 12cms.

12 mm cement plaster in single coat on rough side of single or half brick wall for exterior plastering up to floor two level including brick wall level including internal rounded angles chamfers, and / or rounded angles not exceeding 80 mm in girth and finished even and smooth No. extra for mixing any additive. in 1:4

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture

Providing and fixing concertina coil fencing with punched tape concertinacoil 600mm dia10metre openable length (total length90m), having 50nos rounds per 6metre length, upto 3m height of wall with existing angle iron‘Y’ shaped placed 2.4m or 3.00m apart and with 9 horizontal R.B.T.reinforced barbed wire, stud tied with G.I.staples and G.I.clips toretain horizontal, including necessary bolts or G.I.barbed wire tied to angle iron, all complete as per direction of Engineer-in-arge, with re nforced barbed tape (R.B.T.)/ Spring core(2.5mmthick) wire of high tensile strength of 165kg/sq. mm witht ape (0.52mmthick) and weight 43.478gm/metre (costof M.S.angle, C.C. blocks shall be paid separately)

PUMP ROOM Excavation in foundation in soilmixed with kankar required the use of special tools and plant such as pickaxes- sabbals including lift upto 1.50m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and dosposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30m from the foundation trenches.

Local Sand filling in foundation & Plinth under floor including watering, dressing and incluing proper complirion of work

Concrete with 4cm guage stone ballast, coarse sand and cement in proportion of 1:4:8 in foundation and under floors, including supply of all materials, labour and T&P etc. required for proper completion of the work.

Class-100 Brick work in 1:6 cement and course sand mortar in foundation and plinth including supply of all materials, labour, T&P etc. required for proper completion of work.

Antitermite treatment of soil under floors, apron, footing using chemical emulsion @ one liter per hole, 300mm apart@ 100 Nos holes per 9.00 sqm. Including drilling 12mm diameter holes and plugging also to match the floor properly with chlorpyriphos/Lindane E.C. 20% with i% concentration

Class-100 brick work in 1:6 cement and coarse sand mortar in super structure including supply of all materials, labour, T&P etc. required for proper completion of work upto floor two level.

Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floorV level

R.C.C. work M-20 in Footing with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

R.C.C. work M-20 in Column with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

Painting on D.P.C.or over roof , slab one coat of air blown bitumen S-35 (60/70)or S-90(80/100) grade @one kg./Sqm. Including cost of fuel, wood other materials , labour T & P etc. all complete of work.

R.C.C. work M-20 in lintel beam's and sunsade with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

R.C.C. work M-20 in slab with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (When not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including; supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level.

M.S. Iron work or small sizes and sectin such as holding down bolts, hold fasts, tie rods granite etc. wrought to required from including supply of steel bolts, nuts wastage etc, and their fixing required for proper completion of the work.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Supply & Fixing of fabrication of Z-Section steeel openable window.

Supply & Fixing of 4.00 mm thick Glass Pens in Windows/Ventilators including cost of Putty etc all complete of work.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. agnels 40x40x6mm for diagonal braces upto floor five level

12mm. Thick plaster with cement mortar in proportion of 1 : 4 cement & coarse sand in Plinth with Water proofing material 1lit/bag

12mm thick plaster with cement and coarse sand in 1:4 in single coat on rough side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80 mm in girth and finished even and smooth.(1 Cement: 4 Coarse sand ).

12mm thick plaster with cement and coarse sand in 1:6 of 1.25 F.M. over brick work minimum thickness not to be less than 1cm including supply of all materials, labour T&P etc. required for proper completion of the work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.upto floor five level

P/L integral cement based water proofing treatment BIRCK COBA including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operation: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge Over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment (b) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge to required slope and treating similarly th adjoinin walls upto 300mm height including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth With average thickness of 120 mm and minimum thickness at khurra as 65mm.

4cm (1/2") thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm (1") graded approved stone grit, laid in panels finished with 3mm (1/8") floating coat of neat cement of cement and marble dust in ratio 5:1 as specified over and including 8cm (3") thick without base concrete and removing any overlapping mortar at the joints of panels if any and giving them a uniform finish, supply of all materials, labour, T&P etc. required for proper completion of work.

2.5cm (1") thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm (1") graded approved stone grit, laid in panels finished with 3mm (1/8") floating coat of neat cement of cement and marble dust in ratio 5:1 as specified over and including 8cm (3") thick base concrete consisting of cement, fine sand of 1.25FM and brick ballast 4cm (1½") guage in the proportion of 1:4:8 and removing any overlapping mortar at the joints of panels if any and giving them a uniform finish, supply of all materials, labour, T&P etc. required for proper completion of work.

P/F glass strips of 4mm thick and 3.5cm. Depth in joints of floor and skirting at the time of laying labour, tools, and plants etc. complete.

2 cm thick cement piaster in dado or skirting in 1:3 consisting of one part of cement & two parts of approved coarse sand panels finished with 3 mm floating coat of cement mixed with marble dust in ratio 5:1 including supply of all material, labour, tools & plants etc. required for proper completion of work.

Painting two coat or more over priming coat (including cost of priming coat) on steel and other metal surfaces upto 10cm. width or girth or small articles not exceeding 0.10 sqm in area white superior synthetic enamel such as LUXOL3 Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.

Distempring two coat with O.B.D. distemper of approved brand on undercoated wall surface to give an even shade over Birla putty base and including priming coat of cement primer of approved brand after throughly brushing the surface a free from mortar, dropping and other foreign materials and supply of all materials, labours and T&P etc. complete.

Finishing walls with two coat or more exterior emulsion with silicon additives paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr./10sqm coat curing and cost of all material labour, T&P etc. required for proper completion of work for two coat. upto floor five level

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Supply of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 66 and above Protection . complete in all respect.

Supply of LED Tube Light with batten suitable for up to 1 X 20 watt LED tube light fitting including tube on Surface complete in all respect

Boring/drilling bor well of required dia for casing/strainer pipe, by suitable method presribed in IS: 2800 (part I) incluidng collecting samples from different strata, preparing and submitting strata chart/bore log including hire & running charges of all rquipments, tools plants & machineries required for the job, all complete as per direction of Engineer-in-charge, up to 90 mtr depth below gound level 400mm dia

Boring/drilling bor well of required dia for casing/strainer pipe, by suitable method presribed in IS: 2800 (part I) incluidng collecting samples from different strata, preparing and submitting strata chart/bore log including hire & running charges of all rquipments, tools plants & machineries required for the job, all complete as per direction of Engineer-in-charge, beyond 90 mtr & up to 150 mtr depth below gound level 400mm dia

Supplying , assembling, lowering and fixing in vertical position in bore well, ERW (Electir Resistance Welded) FE-410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge 200mm nominal size diz having minimum wall thickness 5.40mm

Supplying , assembling, lowering and fixing in vertical position in bore well, ERW (Electir Resistance Welded) FE-410 mild steel screwed and socketed/plain ended casing pipes of required dia, conforming to IS: 4270, of reputed & approved make, including painted with outside surface with two coats of anticorrosive paint of approved brand and manufacture, including required hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge 150mm nominal size diz having minimum wall thickness 5.40mm

Supplying, assembling, lowering and fixing in vertical position in bore well, ERW(Electirc Resistance Welded) FE-410 plain slotted (having slot of size 1.6/3.2mm) mild steel threaded and socketed/plain bevel ended pipe (type A) of required dia, conforming to IS: 8110, of reputed and approved make, having wall thickness not less than 5.40mm, including painted with outside surface with two coats of anticorrosive bitumestic paint of approved brand and manufacture, including hire & labour charges, fittings & accessories, all complete, for all depths, as per direction of Engineer-in-charge 150mm nominal size dia

Gravel packing in tube well construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse In required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge.

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/casing pipe removable as per requirement all complete for bore well of 200mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe tube well as per IS: 2800 (Part I), including necessary bolts & nuts of required size complete. 200mm dia

Providing and fixing bail plug/bottom plug of required dia to the bottom of pipe assembly of tube well as per IS: 2800 (part I) 150 mm dia

Development of tube well in accordance with IS : 2800 (part I) and IS : 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit) with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c disinfection of tube well all complete, including hire & labour charges of air compressor, tools & accessories etc. all as per requirement and direction of Engineer-in-charge.

Providing & fixing G.I. pipes complete with G.I. fittings including tenching and refilling etc. (external work)

Supply & Installation of Pump Set 15 H.P. K.S.B. Make with 6" M.S. Column Pipe Starter 15 H.P.V. Meter, A. Meter including pannel box, copper wire 6mm for pupm completion in all respect.Make crompton/bajaj

Supply and laying of aluminium conductor PVC insulated armoured served sheathed cables 1100 Volts grade at a depth of 750 mm below ground level over a cushion of 75 mm. thick sand all around and protected with burnt bricks on sides and on top. On surface the cable run shall be fixed on M.S. clamps etc. of suitable size or as directed by the Engineer-Incharge ,complete in all respect. The armouring of the cable shall be properly connected with the earth conductor by clamps etc.

MAIN GATE Excavation in foundation in ordinary soil (Loam, Clay or Sand) Including lift upto 1.50 m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and disposal of surplus earth as directed by the Engineer In-charge upto a distance of 30m from the foundation trenches.

Providing and laying cement concrete in 1:4:8(1 Cement : 4 Coarce sand : 8graded stone aggregate 40 mm nominal size) and curing complete, Including cost of form work. in Foundation and floors. but in 1:4:8 in coarse sand

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns,pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, including cost of centering, shuttering, finishing and excluding reinforcement 1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

RCC Work Providing and laying in position specified grade of reinforced cement concrete, including the cost of centering, shuttering, finishing and excluding reinforcement - All work up to plinth level :1:1.5:3 (1 cement : 1.5 coarse sand : 3 graded stone aggregate 20 mm nominal size)

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. (TMT Bars) Fe-500

12 mm cement plaster in single coat on rough side of single or half brick wall for exterior plastering up to floor two level including brick wall level including internal rounded angles chamfers, and / or rounded angles not exceeding 80 mm in girth and finished even and smooth No. extra for mixing any additive. in 1:4

Finishing walls with Acrylic Smooth exterior paint of required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Painting with synthetic enamel paint of approved brand and manufactureof required colour to give an even shade : Two or more coats on new work over an under coat of suitableshade with ordinary paint of approved brand and manufacture

GUARD ROOM Excavation in foundation in soilmixed with kankar required the use of special tools and plant such as pickaxes- sabbals including lift upto 1.50m and lead upto 30m and including filling watering and ramming of excavated earth into the trenches or into the space between the building and the sides of foundation trenches or into the plinth and removal and dosposal of surplus earth as directed by the Engineer-in-charge upto a distance of 30m from the foundation trenches.

Local Sand filling in foundation & Plinth under floor including watering, dressing and incluing proper complirion of work

Concrete with 4cm guage stone ballast, coarse sand and cement in proportion of 1:4:8 in foundation and under floors, including supply of all materials, labour and T&P etc. required for proper completion of the work.

Class-100 Brick work in 1:6 cement and course sand mortar in foundation and plinth including supply of all materials, labour, T&P etc. required for proper completion of work.

Antitermite treatment of soil under floors, apron, footing using chemical emulsion @ one liter per hole, 300mm apart@ 100 Nos holes per 9.00 sqm. Including drilling 12mm diameter holes and plugging also to match the floor properly with chlorpyriphos/Lindane E.C. 20% with i% concentration

Class-100 brick work in 1:6 cement and coarse sand mortar in super structure including supply of all materials, labour, T&P etc. required for proper completion of work upto floor two level.

Half brick masonry with common burnt clay F.P.S. (non modular) bricksof class designation 7.5 in superstructure above plinth level up to floorV level

R.C.C. work M-20 in Footing with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

R.C.C. work M-20 in Column with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

Painting on D.P.C.or over roof , slab one coat of air blown bitumen S-35 (60/70)or S-90(80/100) grade @one kg./Sqm. Including cost of fuel, wood other materials , labour T & P etc. all complete of work.

R.C.C. work M-20 in lintel beam's and sunshade with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

R.C.C. work M-20 in slab with cement, approved coarse sand and 2cm guage approved stone grit in proportion of 1:1.5:3 in footing excluding supply of reinforcement and its bending, but including its fixing and binding the same with 24 B.W.G.G.L. binding wire and including necessary centering and shuttering etc. required for proper completion of the work including cost of binding wire.

Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (When not included in an over all rates) wrought to required shape as necessary including bending for proper completion of the work and including; supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level.

M.S. Iron work or small sizes and sectin such as holding down bolts, hold fasts, tie rods granite etc. wrought to required from including supply of steel bolts, nuts wastage etc, and their fixing required for proper completion of the work.

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to steel windows by welding

Supply & Fixing of fabrication of Z-Section steeel openable window.

Supply & Fixing of 4.00 mm thick Glass Pens in Windows/Ventilators including cost of Putty etc all complete of work.

Providing and fixing 1mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. agnels 40x40x6mm for diagonal braces upto floor five level

12mm. Thick plaster with cement mortar in proportion of 1 : 4 cement & coarse sand in Plinth with Water proofing material 1lit/bag

12mm thick plaster with cement and coarse sand in 1:4 in single coat on rough side of single or half brick wall for interior plastering upto floor two level including internal rounded angles not exceeding 80 mm in girth and finished even and smooth.(1 Cement: 4 Coarse sand ).

12mm thick plaster with cement and coarse sand in 1:6 of 1.25 F.M. over brick work minimum thickness not to be less than 1cm including supply of all materials, labour T&P etc. required for proper completion of the work.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.upto floor five level

P/L integral cement based water proofing treatment BRICK COBA including preparation of surface as required for treatment of roofs, balconies, terraces etc consisting of following operation: (a) Applying a slurry coat of neat cement using 2.75 kg/sqm of cement admixed with water proofing compound conforming to IS. 2645 and approved by Engineer-in-charge Over the RCC slab including adjoining walls up to 300 mm height including cleaning the surface before treatment (b) Laying brick bats with mortar using broken bricks/brick bats 25mm to 115mm size with 50% of cement mortar 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to IS : 2645 and approved by Engineer-in-charge over 20mm thick layer of cement mortar of mix 1:5 (1 cement : 5 coarse sand) admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge to required slope and treating similarly th adjoinin walls upto 300mm height including rounding of junctions of walls and slabs (c) After two days of proper curing applying a second coat of cement slurry using 2.75 kg/sqm of cement admixed with water proofing compound conforming to I/s : 2645 and approved by Engineer-in-charge. (d) Finishing the surface with 20 mm thick jointless cement mortar of mix 1:4 (1 cement : 4 coarse sand) admixed with water proofing compound conforming to IS: 2645 and approved by Engineer-in-charge including laying glass fibre cloth With average thickness of 120 mm and minimum thickness at khurra as 65mm.

4cm (1/2") thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm (1") graded approved stone grit, laid in panels finished with 3mm (1/8") floating coat of neat cement of cement and marble dust in ratio 5:1 as specified over and including 8cm (3") thick without base concrete and removing any overlapping mortar at the joints of panels if any and giving them a uniform finish, supply of all materials, labour, T&P etc. required for proper completion of work.

2.5cm (1") thick 1:2:4 plain cement concrete floor with cement approved coarse sand and 2cm (1") graded approved stone grit, laid in panels finished with 3mm (1/8") floating coat of neat cement of cement and marble dust in ratio 5:1 as specified over and including 8cm (3") thick base concrete consisting of cement, fine sand of 1.25FM and brick ballast 4cm (1½") guage in the proportion of 1:4:8 and removing any overlapping mortar at the joints of panels if any and giving them a uniform finish, supply of all materials, labour, T&P etc. required for proper completion of work.

P/F glass strips of 4mm thick and 3.5cm. Depth in joints of floor and skirting at the time of laying labour, tools, and plants etc. complete.

2 cm thick cement plaster in dado or skirting in 1:3 consisting of one part of cement & two parts of approved coarse sand panels finished with 3 mm floating coat of cement mixed with marble dust in ratio 5:1 including supply of all material, labour, tools & plants etc. required for proper completion of work.

Painting two coat or more over priming coat (including cost of priming coat) on steel and other metal surfaces upto 10cm. width or girth or small articles not exceeding 0.10 sqm in area white superior synthetic enamel such as LUXOL3 Hi-gloss apcolite superlac, DULUX specified brushing to give an even shade and including cleaning the surface of all dirt, dust and other foreign matter sand papering and stoping including cost of all materials, labour tools and plants etc. required for proper completion of the work.

Distempring two coat with O.B.D. distemper of approved brand on undercoated wall surface to give an even shade over Birla putty base and including priming coat of cement primer of approved brand after throughly brushing the surface a free from mortar, dropping and other foreign materials and supply of all materials, labours and T&P etc. complete.

Finishing walls with two coat or more exterior emulsion with silicon additives paint (Apex) of approved brand and manufacture and of required shade and undacorated wall surface to give even shade over @ 1.25 Ltr/10sqm including one coat of primer applid @ 0.75Ltr./10sqm coat curing and cost of all material labour, T&P etc. required for proper completion of work for two coat. upto floor five level

Providing and fixing 1st quality ceramic glazed floor tiles conforming to IS : 15622 (thickness to be specified by the manufacturer ) of approved make in all colors, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge in skirting, risers of steps and dados over 12 mm thick bed of cement Mortar 1:3 (1 cement: 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever requiredWhite Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.

aProviding and fixing flexible P.V.C. waste pipe for sink or wash basin including PVC waste fittings completeSemi rigid pipe ) 32mm dia

b) 40mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT Liquid soap container 109 mm wide ,125 mm high and 112 mm distance from wall of standerd shape with bracket of the same material with snap fittings of approved quality and colour weighing not less than 105 gms.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A including jointing with seal ring conforming to IS : 5382 leaving 10 mm gap for thermal expansion . (i) Single socketed pipes.110mm diameter

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over PVC sheet 1m x 1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement,punning,rounding the edges and making and finishing the outlet complete.

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50mm hard wood plugs, screwed with M.S. screws of required length including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete.110mm

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15 cm diameter and weighing not less than 440 grams.

Providing & fixing G.I. pipes complete with G.I. fittings & clamps including cutting & making good the walls etc.20mm dia nominal bore

Painting G.I. pipes and fittings with two coats of anti corrosive bitumastic paint of approved quality.20mm dia nominal bore.

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings including fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.20mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i/c fixing the pipe with clamps at 1.00m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testiang of joints complete as per direction of Engineer in Charge.15mm dia nominal outer dia pipes

20mm dia nominal outer dia pipes

Providing and fixing 45 cm long unplasticised PVC connection pipe with brass unions.15mm nominal bore

Providing & fixing CP brass bib cock of approved quality conforming to IS 893115mm nominal bore

Providing & fixing C.P. brass angle valve for basin mixer and gyser points of approved quality conforming to IS 893115mm nominal bore

Providing & fixing C.P. Brass extension nipple (size 15mmx50mm) of approved make and quality as per direction of Engineer-in-charge.

Providing and fixing gun metal gate valve with wheel of approved quality.20 mm dia nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete20 mm nominal bore

Providing and fixing high density ploythylene water storage loft tank with cover, confirming to IS:12701, colour of opaque white or as approved by Engineer-in-charge. The rate includes making necessary holes for inlet, outlet and overflow pipes. The base support i/c fittings & fixtures for tank shall be paid separately.

Excavating trenches in all kind of soil of required width for pipes, cables etc. including excavation for sockets and dressing of sides, ramming of bottoms, depth upto 1.5 m. including getting out the excavated soil & then returning the soil as required,in layers not exceeding 20cm in depth including consolidating each deposited layer by ramming, watering, etc & disposig of surplus excavated soil as directed within a lead of 50m.Pipes, cables etc. exceeding 80mm dia. But not exceeding 300 mm dia.

Providing, laying and joining glazed stone ware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete.100mm diameter

150mm diameter

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) alround S.W. Pipes including bed concrete as per standard design.100mm diameter S.W. Pipe

150mm diameter S.W. Pipe

Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before with supply and cost of other fIttlings such as elbow,bend,tee and y-tee,Cowel including supply of all marerial labour and T&P. Required for proper completion of work.75 mm O.D.

Supply and fixing of UPVC S.W.R. pipe type-B confirming to IS-13592 including jointing the pipes with rubber ring,lubricant and UPVC SWR cupler confirming to IS-14735. Also including excavation of treanches cutting of walls and holes and repairing the walls,floors and refilling the trenches as before with supply and cost of other fIttlings such as elbow,bend,tee and y-tee,Cowel including supply of all marerial labour and T&P. Required for proper completion of work.110 mm O.D.

Supply and fixing of UPVC S.W.R. pipe nahni trap size 100x75,110/90 mm confirming to IS-14735 self cleaning design fixed in PCC 1:2:4 and supply and fixing of 125 mm dia heavy duty CP brass jali.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required.Group C

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required.

Supplying and fixing modular blanking plate on the existing modular plate & switch box excluding modular plate asrequired.

Supplying and fixing 3 pin, 5 A ceiling rose on the existing junction box/ wooden block including connections etc. as required. (Mirror Light + Wall Fan + Ex. Fan)

Wiring for circuit/ submain wiring alongwith earth wire with the following sizes of FRLS PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required.2 X 1.5 sq. mm + 1 X 1.5 sq. mm earth wire

2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire

Wiring for light/ power plug with 2X4 sq. mm FRLS PVC insulated copper conductor single core cable in surface/ recessed medium class PVC conduit alongwith 1 No. 4 sq. mm FRLS PVC insulated copper conductor single core cable for loop earthing as required.

Supply of water tight oblong 10 Watt LED bulkhead luminaire with driver set confirming to IP 66 and above Protection . complete in all respect.

Supply of LED Tube Light with batten suitable for up to 1 X 20 watt LED tube light fitting including tube on Surface complete in all respect

Supply of Ceiling fan 1200mm sweep, 240V, ball bearing as approved by Engineer in charge complete in all respect.

OHT Earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Providing and laying in position cement concrete 1:4:8 (1cement :4 coarse sand:08graded brick aggregated 40mm .nominal size.) excluding the cost of centering and shuttering - All work upto plinth level

Making plinth protection 50mm thick of cement concrete 1:3:6 (1cement :3 coarsesand : 6graded stoneaggregate 20mm nominal size) over 75mm bed by dry brick ballast 40mm nominal size well rammed and consolidated and grouted with fine sand including finishing the top smooth

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works upto plinth level

Providing and laying in position machine batched and machine mixed design mix M-25 grade cement concrete for reinforced cement concrete work, using cement content as per approved design mix, including pumping of concrete to site of laying but excluding the cost of centering, shuttering, finishing and reinforcement, including admixtures in recommended proportions as per IS: 9103 to accelerate, retard setting of concrete, improve workability without impairing strength and durability as per direction of Engineer-in-charge.“(Note :- Cement content considered in this item is @ 330 kg/cum.“Excess/ less cement used as per design mix is payable/recoverable separately).All works above plinth level upto floor V level

Centering shuttering including strutting, propping etc. and removal of form workFOUNDATION UP TO PLINTH

COL SUPER STRUCTURE

Roof Beam

Staircase

Reinforcement for R.C.C work including straighting,cutting,bending ,placing in position and bending all complete Thermo-Mechanically Treated bars.

230 th Brick work with brick of class designation 75 in foundation & plinth in cement mortar 1:6

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.Fixed to steel windows by welding

15mm thick plaster on the plain in side of mix 1:6 ( 1 cement : 6 fine sand) mortar

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade: New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade Two or more coats on new work over an under coat of suitable sq.m shade with ordinary paint of approved brand and manufacture.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and laying water proofing treatment in sunken portion of W.C., bathroom etc, by applying cement slurry mixed with water proofing cement compound consisting of applying :- (a) First layer of slurry of cement @ 0.488 Kg/Sqm mixed with water proofing cement compound @ 0.253 kg/Sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 Kg/Sqm mixed with water proofing cement compound @ 0.126 kg/Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.

Providing and fixing double scaffolding system (cup lock type) on theexterior side of building/structure, upto 25 metre height, above groundlevel, including additional rows of scaffolding in stepped manner as perrequirement of site, made with 40 mm dia M.S. tube, placed 1.5 metrecentre to centre, horizontal & vertical tubes joint with cup & lock systemwith M.S. Tubes, M.S. tube challis, M.S. clamps and staircase system inthe scaffolding for working platform etc. and maintaining it in a serviceablecondition for execution of work of cleaning and/ or pointing and/ orapplying chemical and removing it thereafter. The scaffolding systemshall be stiffened with bracings, runners, connecting with the building etc,wherever required, if feasible, for inspection of work at required locationswith essential safety features for the workmen etc., complete as perdirections and approval of Engineer-in-charge.

Water OHT Tank Level Indicator, 20 meter

LANDSCAPPING Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure).

Supplying and stacking of good earth at site including royalty and carriage upto 5 km lead complete (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking well decomposed cow dung manure at site including royalty and carriage upto site (cow dung measured in stacked will be reduced by 8% for payment.)

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge

Preparation of beds for hedging and shrubbery by excavating 60 cm deep and trenching the excavated base to a further depth of 30 cm, refilling the excavated earth after breaking clods and mixing with sludge or manure in the ratio of 8:1 (8 parts of stacked volume of earth after reduction by 20%: one part of stacked volume of sludge or manure after reduction by 8%), flooding with water, filling with earth if necessary, watering and finally fine dressing, leveling etc. including stacking and disposal of materials declared unserviceable and surplus earth by spreading and leveling as directed, within a lead of 50 m, lift up to 1.5 m complete (cost of sludge, manure or extra earth to be paid for separately)

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) Holes 60 cm dia, and 60 cm deep

Shrubs plants Trees/ Exotic Plants: Supply and plantation of plants as per sample approved by the engineer. Plants should be quite healthy, disease free as per ht. & specification given below. Species can be changed as per site requirement and as per directions of engineer.Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Ficus blackii (F.vivion) of height 45-60 cm. with 6- 8 branches healthy foliage in earthen pots of size 25 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus black vivion piller Topiary (sylinder type) well developed with fresh & healthy 180 to 210 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Bottle palm of ht. 150-180 cm bottom girth 20-25 cm well developed in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Polyalthia pendula (Ashok Pendula) of height 180-195 cm. in gunny bag of size 30 cm as per direction of the officer-in-charge.

Standard Rose (H.T. variety) 3 to 4 healthy branch 90 cm and above ht. well developed with one and above flowers in 25 cm Earthen Pot,

Providing & Fixing of Bolard light in park

Street Pole with LED Lamp : Supply and fixing of 7 mtf. G.l. Octagonal pole of approved make(top dia 01 No . 21657.00 )302.OO 70 mm, Bottom dia 130 mm Base plate 12 mm thick) having 3 mm, thickness with single arm bracket length of 1 mtr. length in t :2 :4 RCC foundation boh including the cost of foundation , excavation & back filling and Required T & P complete in all respect.

Supply and fixing of LED Street light Fitting having die cast aluminium body and diffuser with driver set suitable for 75 to 90 |Watt. Confirming to IP 66 and above Protectlon complete in all respect. CAT AAA

Supply and fixing of 240 volts C Curve 6-32 amp SP miniature circuit breaker (10 KA) in existing MCB, DB complete with Each 25 Connections as rèquired, CAT A Single Pole

supply and fixing following capacity of automatic street Iight cubicle control pannel with anti corrosive alkali and acid proof paint consisting of tine switch TSO 100 seeries with contactors, HRC fuse, isolating switch, metering instrument and instrument box with CTs etc.ccmplete in all respect.

Supply and burying of Safe Earthing Electrod T-19 Zn-Zinc Coated, Length 3000mm, outer pipe 48.4mmx3.2mm, inner pipe 26.9mm x 2.6 mm, terminal Dia 12mm, coating 80-100 micron filled with crystalline conductive mixture (CCm) having anti corrosive & conductive property with 50 Kgs activated soil (BFC) capable of reducing the soil resistivity with good mixture of retaining capacity along with 30 cm square C.I. frame with hinged cOver & masonary housing.(From electrode terminal to switch board,cost of 25x3 G.J. Strip wil! be extra) Make: As approved in U,P.P.W.D, & C.P.RI. Certified.

Supplying and laying 25 mm X 5 mm G.l strip at 0.50 metre below ground as strip earth electrode, incduding connection/ terminating with G.I. nut, bolt, spring, washer etc. as required. (Jointing shall be Rmt. 250 done by overlapping and with 2 sets of G.I. nut bolt & spring washer spaced at 50mm)

Supply and fixing of two number 8 SWG G.l. wire in 15mm dia. G.. pipe for earthing, laid in ground or in wall duly concealed including the cost of cernent, sand, labour, T&P other material required for| proper compietion of work as directed at side.

Providing, laying arnd fixing following dia G.l. pipe (mediun,class) in ground complete with G.I, fittings including trenching (75 cm deep)and re-filling etc as required.100 mm dia

RECHARGE WELL Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth

In all kind of soil upto 1.5m to 3.0m. Depth

In all kind of soil upto 3.0m to 4.5m. Depth

In all kind of soil upto 3.0m to 4.5m. Depth

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors.

M-150 brick work in 1:4 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work.

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in Slab and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200.

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level.

15 mm cement plaster in single coat on rough side of single or half brick wall for interior plastering up to floor two level including internal rounded angles not exceeding 80 mm in girth and finshed even and smooth. (1) 1 cement : 4 Coarse sand

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:With 20x20mm square bar

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 560mm internal diameter

Boring/drilling bore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-incharge, upto 90 metre depth below ground level. Drilling of 300mm dia bore hole manually.

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.150 mm nominal size dia

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling coarase sand of size range 1.5 mm to 2mm in recharge pit, in required thickness over gravel layer, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/medium/coarse, in required grading & size as per actual requirement, all complete as per direction of Engineer-in-charge.

DESILTING CHAMBER Earth work in excavation by mechanical means (Hydraulic excavatior)/manual means over areas(exceeding 30cm in depth. 1.5m in width as well as 10sqm on plan) including disposal of excavated earth, lead upto 50m and lift upto 1.5m, disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth

In all kind of soil upto 1.5m to 3.0m. Depth

In all kind of soil upto 3.0m to 4.5m. Depth

Providing and laying in cement concrete 1:4:8 (1 cement :4 coarse sand :8 graded Stone aggregate 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors.

M-150 brick work in 1:4 (one cement and six coarse sand sand of 2.25 fineness modulus) mortar in foundation & plinth including supply of all materials, labour and T & P etc required for proper completion of the work.

R.C.C. work with cement approved coarse sand and 20 mm. guage approved stone grit im the proportion of 1:1.5:3 in Slab and windows excluding supply of reinforcement and its fixing and binding the same with 24 BWG binding wire and including necessary centering and shuttering etc.and also including supply of all materials, labour and tools and plants etc, required for proper completion of the works. strength of the concrete shall not beless than M-200.

P/F Mild steel or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level.

15mm cement plaster on rough side of single or half brick wall mix 1:4 (1 cement : 4 coarse sand)

Providing M.S. foot rests including fixing in manoholes with 20x20x10 cm cement concrete blocks 1:3:6 (1cement : 3 coarse sand : 6 graded stone aggregate 20mm nominal size) as per standard design:With 20x20mm square bar

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.Rectangular shape 900x600 mm internal dimension.

DRAINAGE NETWORK Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Excavating trenches in all kinds of soil of required width for pipes. including excavation for sockets and dressing of sides, ramming of bottoms, including getting out the excavated soil & then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer by ramming, watering, etc & disposing of surplus excavated soil as directed within a lead of 50m.up to 1.50 m depthPipes 80 mm to 300 mm diameter

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150mm diameter

Providing & laying cement concrete 1:5:10 (1 cement :5 coarse sand :10 graded stone aggregate 40mm nominal size) all-round S.W. Pipes including bed concrete as per standard design.150mm diameter

Chlorinator

Earth Filling

DRAIN Excavation of foundation in ordinary soil (loam clay or sand) including lift upto 1.50 meter and lead upto 30 meter and including filling, watering and ramming of excavated earth into the trenches or into the space between the building and sides of foundation trenches or into the plinth and removal and disposal of sur-plus earth as directed by the Engineer incharge up to a distance of 30 meters from the foundation trenches.

Providing and laying in position ready mixed or site batched design mix cementconcrete for plain cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana/Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering and finishing as per direction of the engineer-in-charge; for the following grades of concrete.Concrete of M10 grade with minimum cement content of 220 kg /cum

First Class brick work in 1:3 cement and coarse sand of 2.25 F.M. mortar in foundation and plinth including supply of all materials, labour, tools and plants etc. required for proper completion of the work. (1:6 cement & coarse sand).

15 mm cement plaster on rough side of single or half brick wall of mix : 1:4 (1 cement: 4 coarse sand)

40mm thick 1:2:4 plain cement concrete floor (1 cement :2 coarse sand :4 graded stone aggregate 12-20mm nominal size laid in one layer neat cement.

Providing and placing in position 100 mm thick factory made machine batched & machine mixed Precast RCC Rectangular Covers on drains of footpath of various sizes, of M-25 grade cement concrete for RCC work, including cost of centering, shuttering, reinforcement of 8 mm dia TMT bars of Fe 500 grade @ maximum 100 mm c/c on both ways, neat cement punning on finished surface, properly encased on all edges with 1.6 mm thick, 100 mm wide MS sheet duly painted over priming coat, reinforcement to be welded at edges with MS sheet and providing 2 Nos. 12 mm dia bar for hooks etc including cost of cartage, all leads & lift, handling at site etc. all complete as per direction of Engineer-in-Charge

C.C ROAD Construction of granular sub-base by providing close graded Materialconforming to specifications, mixing in a mechanical mix plant at OMC,carriage of mixed material by tippers to work site, for all leads & lifts,spreading in uniform layers of specified thickness with motor grader onprepared surface and compacting with vibratory power roller to achieve thedesired density, complete as per specifications and directions of Engineerin-Charge With material conforming to Grade-II (size range 53 mm to0.075 mm ) having CBR Value-25

Preparation and consolidation of sub grade with power road roller of 8 to12 tonne capacity after excavating earth to an average of 22.5 cm depth,dressing to camber and consolidating with road roller including makinggood the undulations etc. and re-rolling the sub grade and disposal ofsurplus earthwith lead upto 50 metres.

Construction of dry lean cement concrete sub base over a prepared sub gradewith coarse and fine aggregate conforming to IS:383, the size ofcoarse aggregate not exceeding 25 mm, aggregate cement ratio not toexceed 15:1, aggregate gradation after blending to be as per specifications, cement content not to be less than 150 Kg/cum, optimum moisture conten tto be determined during trial length construction, concrete strength not tobe less than 10 Mpa at 7 days, mixed in a batching plant, transported tosite, for all leads & lifts, laid with a mechanical paver, compacting with 8-10tonne vibratory roller, finishing and curing etc. complete as per direction of Engineer-in- charge

Providing and laying design mix cement concrete of M-30 grade, in roads/taxi tracks/ runways, using cement content as per design mix, using coarsesand and graded stone aggregate of 40 mm nominal size in appropriateproportions as per approved & specified design criteria, providing dowelbars with sleeve/ tie bars wherever required, laying at site, spreading andcompacting mechanically by using needle and surface vibrators, levellingto required slope/ camber, finishing with required texture, including steelform work with sturdy M.S. channel sections, curing, making provision forcontraction/ expansion, construction & longitudinal joints (10 mm wide x50 mm deep) by groove cutting machine, providing and filling joints withapproved joint filler and sealants, complete all as per direction of Engineerin-charge (Item of joint fillers, sealants, dowel bars with sleeve/ tie bars tobe paid separately).Note:- Cement content considered in M-30 is @ 340 kg/cum. Excess/ lesscement used as per design mix is payable/ recoverable separately.2 Cement concrete manufactured in automatic batching plant(RMC plant) including transportation to site in transit mixer

Steel reinforcement for R.C.C. work including straightening, cutting,bending, placing in position and binding all complete upto plinth level. Thermo-Mechanically Treated bars of grade Fe-500D or more. (TMT Bars) Fe-500

Centering and shuttering including strutting, propping etc. and removal of form for Foundations, footings, bases of columns, etc. for mass concrete.

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners,etc

Providing and laying in position bitumen hot sealing compound for expansion joints etc.Using grade 'A' sealing compound.

Extra for providing and mixing hardening compound of approved quality as per manufacturer’s specification in cement concrete.

SEPTIC TANK Earth work in excavation over areas including disposal of excavated earth, lead upto 50m, disposed earth to be levelled and neatly dressed.In all kind of soil upto 1.5m depth

In all kind of soil upto 1.5m to 3.0m. depth

In all kind of soil upto 3.0m to 4.5m. depth

Providing and laying in cement concrete 1:4:8 (1 cement : 4 coarse sand : 8 stone ballast 40 mm nominal size) and curing complete,including cost of form- work, in foundation and floors.

Brick work with brick of class designation 150 in foundation and plinth in cement mortar (1 cement : 4 coarse sand)

Reinforcement cement concrete work in RCC culvert slab with 1:1.5:3 (1 cement : 1.5 coarse sand and 3 gradded stone aggregate of 20 mm nominal size) including centering and shuttering and reinforcement. M20

TMT Fe-500 or iron in plain work such as reinforced concrete or reinforced, brick work (when not included in over all rates ) wrought to required shape as necessary including bending for proper completion of the work and including supply of steel its wastage bend hooks and authorised over lapping shall be measured upto floor two level.

15 mm cement plaster on plinth of mix : 1:4 (1 cement: 4 coarse sand). F.M.-2.25

Providing M.S. foot rest including fixing with 20x20x10 cm. cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 gradded aggregate of nominal size 20mm ) as per standard design with 20x20mm sq bars.

Providing and fixing S.C.I. tee 150 mm at the inlet and outlet of septic tank.

Providing & fixing 75mm dia vent pipes.

Providing & fixing of 75mm dia cast iron terminal guard.

Providing and fixing in position precast RCC manhole cover and frame of required shape and approved quality.M.D. -10- Circular shape 500mm internal diameter

L.D. -2.5- Circular shape 450mm internal diameter

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks of class designation 150 and S.W. drain pipe 100 mm diameter, 1.8m long complete as per standard design.

GST Paid extra as per applicable/

Please Enable Macros to View BoQ information