SPECIAL REPAIRS TO CHANDRAGUPTA HALL OF F COMBAT, BLDG NO. ET-215 OF INI, PROVISION OF WAITING AREA FOR MI ROOM AND CERTAIN REVENUE AND MINOR WORKS AT CME

Amount

Roughening surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust, etc. all as directed.

M&L for PVC Vinyl tiles/sheets 3mm thick, laid with approved rubber based adhesive in floors as per manufactures specification etc all as directed by Engr in Charge Make : Wonder floor, Parador, Vinyak or equivalent

Dismantling boarding , any description, fixed in any position with nails complete all as directed.

Dismantling timber fillets in framed work, rails, posts, rafters, purlins etc. under 40 sq. cm in section, in any position all as directed.

S&F Veneered decorative plywood with decorative veneers on external face over on 12mm thick commercial plywood fixed with nails/adhesive/screws to match with existing shade / type etc complete all as specified and directed

S&F second class HW fillets, square, rectangular or triangular in section, clean sawn for fixing plywood on wall, sectional area exc 13 sqcm and not exc 25 sqcm secured with nails / screws to wall complete all as specified and directed.

M&L for Preparation of new or previously untreated surfaces of wood of any description width or girth including filler coat and applying French polishing on surfaces of any description but two or more coats on new surfaces etc complete all as specified and directed

M&L for French polishing on surfaces of any description, width or girth including cleaning and preparing the surface including a coat of wood filler but one or more coats on old wooden surfaces etc complete all as specified and directed by Engr in Charge

M&L preparation of old wooden surfaces over 10cm width or girth and applying one coat of synthetic enamel paint all as specified and directed by the Engineer-in-Charge.

Taking down cement plaster any description from roof slab, stone wall, brick wall parapets including raking out joints hacking for key and scrubbing down with water etc complete all as specified and directed.

M&L rendering 15mm thick on stone masonry surfaces in CM 1:4 finished even and smooth with sagol over and including dubbing out average 10mm thick on irregular face of walls in CM 1:6 complete all as specified and directed.

M&L Preparation of newly plastered or unplastered surfaces of wall and applying two coats of distemper oil emulsion paint over one coat of primer complete all as specified and directed.

M&L preparation of old steel or iron surface of any description, over 10 cm width or girth not otherwise described and applying one coat of synthetic enamel paint all as specified and directed by Engineer-in-Charge.

M & L for Perforated particle board/tiles for insulation and accoustic purposes, 60x60 cm in size, 12mm thick, fixed with nails to timber frame work or with staples on snap grid complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings exceedidng 15cm thickness (above ground floor) all as specified and directed.

M&L 100mm thick cement concrete 1:3:6 type C2 (40mm graded stone aggregate) as in floors, plinth, path etc smooth finished surface without using extra cement complete all as specified and directed.

M&L for 75 mm thick PCC 1:4:8 type D-2 using 40mm graded stone aggregate as in subbase all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premishes complete all as specified and directed.

M & L joint free Non-skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floor etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including provision of screed bed 15 mm thick in cement mortar 1:4 complete all as specified and directed.

M & L for glazed ceramic coloured tiles of size 350mmx250mmx7mm/ 450mmx350x7mm thick on vertical surfaces such as skirting, dado, etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over backing coat 10mm thick cement mortar in 1:4 complete all as specified and directed.

Dismantling wall and ceiling boards fibre, pulp, insulation boards/ slabs/ blankets any thickness including cover fillets all as specified and directed

M & L for SG Gypoc T-Grid false ceiling system with 12 mm thick panel laminated with PVC film on face side and metalised polyster film on the back with all four edges scaled with PVC film ceiling tiles including all necessary ancillaries and fixing arrangement as per manufacturer's instructions in the grid size 600x600 mm with consisting of main Tee on wall of size 38mm x 24 x 0.3mm, Cross Tee of size 25mm x 24mm x 0.3mm, wall angle of size 20mm x 14mm x 0.4mm using purpose made members interlocking to each other and with level clips and making holes etc all as specified and directed. Make - Gyproc (Gyprex), Armstrong or equivalent.

M & L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coats of Oil bound distermper white or tinned over one coat of primer on walls etc all as specified and directed.

Taking up or down 15mm bore steel water tubing & connections including cleaning for refixing or offering credit as per schedule of credit all as directed.

All as per item No. 24 above, but 20 mm bore

S & F 15mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

S & F 20 mm bore medium grade galvanised steel water tubing with all fitting & fixed complete to walls or ceiling or laid in floors all as specified and directed.

Refixing 15 mm bore old steel water tubing & connection in new or old position of wall, ceiling, floor etc all as specified and directed.

All as per item No. 28 above, but 20mm bore

Note for sl item no. 28 & 29 : serviceable steel tubing obtained from sl item no. 24 & 25 shall be re-used in these items

S & F in repair vitreous China wash basin, white, flat back, size 630x450mm excluding taps, waste chain and plug and porcelain stopper but including brackets, waste coupling and including cutting for and pinning in ends of brackets or erecting stand complete all as specified and directed.

S & F in repair vitreous China wash down water closet pan (pedestal pattern) white (excluding fixing bolts, flushing cistern and flush pipe) including P or S trap provision of flush pipe, plastic seat cover for pedestal pan complete all as specified and directed.

S & F in repair 10 ltr capacity PVC valveless, syphonic action type flushing cistern, low level, white with inlet ball valve, float and handle including bracket and 32 mm dia flush pipe of polyethylene of low or high density for low or high density for low level cistern complete all as specified and directed

S & F in repair 15mm dia pillar taps, cast copper alloy with capstan heads, chromium plated fancy type, screwed down high pressure with or without lettered 'Hot' or 'Cold' with long shanks and flynuts, screwed for iron pipe complete all as specified and directed.

S & F PVC connection 15 mm size with PTMT nuts of length 450mm complete all as specified and directed

S & F in repair 2 in 1 hand shower (Health Faucet) with 1 metre long easy flex tubein chrome finish & wall hock all as specified and directed. Make : Prayag Roman (unbranded)

S & F in repair 15 mm 2 way Bib cock (unbranded)

S & F in repair 75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints fixed to walls complete as all specified and directed.

All as per item No. 37 above, but 110mm bore complete all as specified and directed

S & F in repair 75 mm bore PVC (SWR) bend any radius complete alll as specified and directed

All as per item No. 39 above, but 110mm dia complete all as specified and directed

S & F in repair 75mm bore PVC (SWR) junction single (single T) equal or unequal complete all as specified and directed.

All as per item No. 41 above, but 110mm bore of pipe complete all as specified and directed.

M & L in repair 75 mm dia PVC (SWR) floor trap with grating including jointing with solvent cement complete all as specified and directed.

All as per item No. 43 above, but 110mm dia complete all as specified and directed

S & F in repair 75mm dia PVC (SWR) vent cowl complete all as specified and directed.

All as per item No. 45 above, but 110mm dia complete all as specified and directed.

Supply and fix recess mounted LED downlighter elegantly designed die-cast AI heat sink for effiecient heat dissipation and separate replaceable electronic driver of ceiling cutout dia 180 mm, height 68mm of Cat part No. ENDURANEODKR21WLED840S OF HAVELLS all as directed by Engr-in-charge

Supply and fix recess mounted LED wall washers, tilted 70 degree outwards and swivels 360 degree to offer best illumination on the wall and retail displays of Cat part No. SPARKLEPROSNOOT DLR30WLED830MOD38D & LEDDRIVER30WS OF HAVELLS all as directed by Engr-in-Charge

Supply and fix VTPN MCCB 125A DB-double door with provision for FP MCB/isolation/RCCB etc as incommer and SP/ TP MCBs as out going double door IP 54 protection complete prewired including Bus Bar etc suitable for operation on 415 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the bricks /stone masonry etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed by Engineer-in-Charge [ Make: Indoasian /schneider/ Siemens]

Supply and fixing of MCB four pole rating capacity 40 A, 240 V breaking capacity 9KA C series all as specified and directed.

Supply and fixing of MCB single pole and neutral rating capacity 40 Amp, 240 V breaking capacity 9KA C Series all as specified and directed

Supply and fixing of MCB single pole rated capacity 5 to 32 A, 240 V breaking capacity 9KA C series all as specified and directed

Supply and fix VTPN MCCB 250A DB double door with provision for FP MCB/isolator/RCCB etc as incommer and SP/ TP MCBs as out going double door IP 54 protection complete prewired including BUS bar etc suitable for operation on 415 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified and as directed by Engineer-in-Charge. [ Make : Indoasian /Schneider/ Siemens ]

S & F submain wiring with approved colour coding as per TS with four single core PVC insulated cable with stranded copper conductor of size 06 Sq. mm nominal area and drawing through PVC non metalic PVC casing caping including PVC insulated 4 Sqmm (nominal area) stranded copper conductor earth wire complete. Note : Four runs of 6 sqmm cable, one run of 4 sqmm cable and one run of PVC casing caping will be measured as one unit

S & F sub main wiring with approved colour coding as per TS with two single core PVC insulated cable with stranded copper conductor of size 04 Sq. mm nominal area and drawing through PVC non metalic casing caping including PVC insulated 1.5 Sqmm (nominal area) stranded copper conductor earth wire complete. Note : Two runs of 4 sqmm cable, one run of 1.5 sqmm cable and one run of PVC casing caping will be measured as one unit

Supply & fix metal clad P & S box for AC, IP 30 protection capacity 32A 4P cat No. 811958 of Indoasian make all as directed by Engr-in-Charge

Supply & fix single sided LED signage with built in battery backup for 2 Hrs colour red & green of Cat No. 220208 & 220209 of Bajaj all as directed by Engr-in-Charge.

M & L for Earthing complete with galvanized steel plate electrode 60 cm x 60cm x 6mm thick surrounded by charcoal and salt, buried directly in ground vertically in a pit of depth not less than 2.25 metre below ground level with the edge of the earth plate at a depth of not less than 1.50 metre below ground level connected to galvanized iron or steel earth wire, 4 mm dia (No. 8 SWG) by means of bolts, nuts, check nuts and washers of galvanized iron, earth wire protected by galvanized steel pipe 15mm dia (light grade) & connected to main switch of main control board all as shown in electrical plate No. 3 of SSR-2009 part I & including neccessary excavation and earth work. The rate also include charcoal and salt in alternate layers 20 mm dia pipe (Light grade) for watering protection pipe, funnel, wire mesh, PCC chamber in cement concrete (1:3:6) type C-I, 40 mm thick RCC (1:2:4) type B-1 cover CI frame etc. all as specified and directed.

Excavation in post holes (or similar hole) each n. exc 0.50 cu m getting out in hard/dense soil returning, filling in, and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm, watering and removing surplus soil to a distance n. exc. 50 m and making good disturbed surface complete all as specified and directed.

Material and labour for plain cement concrete 1:2:4 type B-2 using 40 mm graded crushed stone aggregate as in foundation, filling and mass concrete in post hole complete all as specified and directed.

S & F steel work of grade Fe-410W (Gde E-250) quality B in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc complete all as specified and directed. Note: Steel frame work will include post, truss, purlin, rafter, runner, bracings etc.

S & F of Fe 410-W (Gde E-250) quality - B mild steel plates, plain or chequered, 5 mm thick or over in thickness in available sizes channels, square cuts or notched (ordinary or counter sunk) forming holes without any attachment complete all as specified and directed.

Material and labour for preparation of new or previously, untreated surfaces of steel or iron of any description over, 10 cm in width or girth, not otherwise described and applying two coat of synthetic enamal paint over one coats of red oxide zinc chrome primer all as specified and directed.

S & F 20mm bore stop valves cast copper alloy screwed down high pressure with crutch or butter fly handle screwed both ends for iron pipe all as specified and directed.

Material and labour 20mm bore dia ball brass valves, high pressure with polythene float and flynut complete screwed for iron pipe or brass ferrule complete all as specified and directed. Make : Prayag

Supply and fixing 750 ltr capacity rotational moulded polythylene water storage tanks (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Part I complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S & F steel work with tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161-1998 grade St.-240 complete all as specified and directed by Engineer-in-Charge.

S & F welded steel wire fabric n. exc. 4 Kg to wood or steel members complete all as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

S & F pre painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws as specified and directed.

Provision of scaffolding, props as required and approach system from outside of the high rise tower to enable execution of all items of work by using steel tubular structure of double wooden scaffolding complete with necessary support/ propping system etc complete for safe working. The scaffolding shall have arrangement of certain appropriate material to arrest debris or waste material as and when the work is over and carting away the material.

Surfaces excavation n. exc (not exceeding) 30 cm deep and averaging 15 cm, deep and getting out in hard/ dense soil complete all as specified and directed.

M & L precast solid block masonry of block 1:3:6 type C-1 using 20mm graded stone aggregate wall exceeding 10 cm in width and built in cement mortar 1:6 complete all as specified and directed

M & L hardcore using broken stone boulders not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surfaces complete all as specified and directed.

Supply only fine aggregate (sand) for sand cousioning 50 mm thick etc complete all as specified and directed by Engr-in-Charge

M & L machine pressed precast concrete interlocking pavour block with grey cement and pigment any shape and size conforming to IS 15658-2006 of 60mm thickness M-35 grade with glossy finish colour shade complete all as specified and directed by Engr-in-Charge.

M & L 15mm thick plastering on concrete surfaces in CM 1:4 finished even and smooth without using extra cement complete all as specified and directed.

M & L preparation of newly plastered or unplastered surfaces on wall and applying two coats of cement base paint complete all as specified and directed.

M & L PCC 1:2:4 type B-1 (using 20mm graded crushed stone aggregate) in lintels upto 1.5m clear span, cills, steps, seismic and other similar brands, plinth courses, string courses, lacing courses, parapets and railing upto 60 cm in height, copings, kneelers, apex stones, bed plates, kerbs, water troughs and the like including weathering, slightly rounded for chamfered angles and throating as specified and directed.

M & L for surface dressing n. exc 15 cm deep and getting out in soft/ loose soil complete all as specified and directed.

M & L for excavation in trenches not exc 1.50 m wide and not exc 1.50 m depth for foundation etc n. exc 10 sqm on plan and getting out in hard/ dense soil complete all as specified and directed.

M & L machine cut cuddappah stone slab 20-25 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing over and including 15mm thick screed bed in CM 1:4 complete all as specified and as directed.

M & L 20-25 mm thick granite (of any type) in kitchen platform machine cut and mirror polish bedded over cement mortar screed 15 mm thick 1:4 and jointed in grey cement slurry and pointed in white cement with admixture of pigment to match the shade of granite stone including grinding etc complete all as specified and directed.

Rounding to edges of stone slabs such as in steps, cooking platform and other similar situation complete all as specified and directed.

Returning, filling in, inclduing spreading, levelling, watering and well ramming in layers not exc 25 cm in hard/ dense soil complete all as specified and directed.

Removing excavated material n. exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point complete all as specified and directed.

Dismatling tiling of single layer mangalore pattern roof tile laid dry complete all as specified and directed.

All as per item no. 87 above, but bedded in lime or cement mortar complete all as specified and directed.

Dismantling battens for tiles, shingles etc. of any size including tilting fillets spacing exc 15 cm complete all as specified and directed.

M & L for roof tiles, mangalore pattern, interlocking at side joints laid dry complete all as specified and directed.

All as per item No. 90 above, but except tile complete Note : Serviceable tiles obtained from sl item no. 87 shall be re-used in this item.

M & L for ridge tiles, mangalore pattern, set and jointed in CM 1:6 complete all as specified and directed.

All as per item No. 92 above, but except mangalore pattern ridge Note : Serviceable ridge obtained from sl item no. 87 shall be re-used in this item.

S & F rolled sections as in main and cross, beams, hips and jack, rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates etc Fe-410-W (Gde E-250) quality A complete all as specified and directed.

S & F 0.63 mm thick galvanised, corrugated mild steel sheeting with two corrugated side laps, fixed with 'L' hook or 'J' hook in roofs walls etc with grade of zinc coating 275 complete all as specified and directed.

S & F 0.63 mm thick galvanised, mild steel sheeting in ridges, hips, valley, gutters, drips and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified and directed.

Dismantling timber scantling 40 sqcm and over in section in any position in framed work complete all as specified and directed.

Demolition of brick or stone/ boulder masonry, built in cement mortar including all quoins, arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles complete all as specified and directed.

M & L walling of random rubble, uncoursed, well bonded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

All as per item No. 99 above, but except stone complete all as specified and directed. Note : Serviceable rubble obtained from sl item no. 98 shall vbe re-used in the work.

M & L raised pointing in CM 1:4 to random or polygonal rubble, uncoursed or brought upto courses complete all as specified and directed.

M & L complete removal of existing treatment and applying 3mm thick Birla wall care putty and applying two coats of Oil bound distemper white or tinned over one coat of primer on walls etc all as specified and directed.

M & L complete removal of existing treatment and applying two coat of white wash on walls surface complete all as specified and directed.

All as per item No. 103 above, but two coats of cement base paint complete all as specified and directed.

AJINKYA VIKRAM GAIKWAD