SPL REPAIR TO BLDG NO SB 3/1 TO 3/9 NALWA LINES (OR MD ACCN), ADDN/ALT FALSE CEILING, AL DOOR/WINDOWS AND FLOOR TILING OF BLDG NO 7 AND ADDN/ALT TO GATE PILLAR AND STEEL GATE AT 2 USMAN, HQ CELZ AND AGE B/R-II UNDER GE (WEST) LUCKNOW

Amount

Demolition of brick work or stone/ boulder masonary, built in cement mortar or cement lime mortar including all quions, arches, pillars, etc. but excluding ashlar facings, dressed stone work and precast concrete articles etc. complete all as specified and directed.

Dismantling existing water proofing treatment of any description from roof surfaces and removing rubbish to a distance not exc. 100m, complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not exc. 15 cm thickness (below or above ground level) complete all as specified and directed.

Taking down cement or cement lime plaster any description from walls/ceiling etc including racking out joints, hacking for key & scrubbing down with water all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area n. exc 1.50 Sqm each complete all as specified and directed. (Note:- cutting hole in wall is deemed to be included in the rate quoted)

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exc 1.50 Sqm but n. exc 4sqm each complete all as specified and directed. (Note:- cutting hole in wall is deemed to be included in the rate quoted)

Taking down eaves gutters rain water pipes (any size or pattern), including all fittings, heads, shoes, bends, swan necks, etc. including cleaning for refixing or removal from site (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L Cement Concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in lintels upto 1.5m clear span, cills, steps, seismic and other bands, plinth courses, string cources, lacing cources, parapets and railing upto 60cm in height, copings, kneelers, apex stones, bed plates, water troughs, hold fasts and the like including weathering, slightly rounded or chamfered angles and throating including necessary formwork complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:6 complete all as specified and directed.

M&L brick work with old size fly ash bricks of class designation 75, straight or curved on plan exceeding 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

M & L Cutting chases, pinning in, for concealed water tubing etc. in brick walls and making good to disturbed surface in cement mortar 1:3, cutting not exceeding 20cm in girth complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:6 on fair faces of brick work or concrete surfaces of wall and finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for rendering 15mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

M&L for rendering 10mm thick in CM 1:3 on ceiling finished surface even and smooth without using extra cement complete all as specified and directed.

M&L for screed bed 10mm thick in CM 1:4 with integral water proofing compound @ 3% by weight of cement on fair faces of brick work or concrete surface of wall and finished surface even and smooth without using extra cement complete all as specified and directed. NOTE: WPC shall be measured and paid seperately under respective item.

Supply only integral waterproofing compound complete all as specified and directed.

M&L for 75mm thick cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate as in plinth protection, laid in panels, finished surface even and smooth without using extra cement and forming 12mm wide expansion joints to the full depth, and filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound, Grade 'A' complete all as specified and directed.

M&L plain Cement Concrete 1:3:6 type C-0 (using 12.5mm graded stone aggregate) as in filling in pressed steel frames complete all as specified and directed.

M&L for cement concrete 1:3:6 type C-1 (using 40 mm graded stone aggregate) as in surface channels and drains complete all as specified and directed.

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using extra cement, including forms, moulds, mitred/ stopped ends etc complete all as specified and directed.

S&F Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted,or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walkways; railings; framework of water tanks and similar work quality conforming to Fe-290 Gde-E-165 complete all as specified and directed.

M&L providing and injecting chemical emulsion along the external wall below concrete or masonry apron using chemical emulsion @ 2.25 litres per linear meter including drilling and plugging holes etc. in apron complete all as specified and directed.

M& L treating of soil under existing floors using emulsion @ one litre per hole,300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement :2 coarse sand) to match the existing floor complete all as specified and directed.

S & F pressed steel door frames of size 125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S & F pressed steel door frames of size 105 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and directed.

S&F 35mm thick 2nd class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauze etc, divided into squares, with plain, chamfered or rounded, metred and rebated shash bars, any numbers, edges of framing plain, chamfered or rounded, fitted with cut or mitred beads for securing glass, gauge etc sizes of members of shutters as specified in SSR Part-I Section 8 clause 8.24(a) and fitted to chowkats complete all as specified and directed.

S&F powder coated (thickness of powder coating not less than 50 micron) anodized aluminium glazed window and ventilator shutters, side hung/ top hung type without sash bars, with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as 01 no. 150mm long peg stays, 02 nos. 100mm long hinges type B-21, 01 no. 150mm long tower bolts and 01 no. 125mm long handles complete all as specified and directed

S&F anodized aluminium powder coated (thickness of powder coating not less than 50 micron) glazed door shutters with aluminium sections weighing not less than 0.55kg/m including necessary joining cleats, glazing clips, rubber packing, anodized aluminium snap beading, screws, anodized aluminium fittings such as hinges, tower bolts and handles etc. complete all as specified and directed.

S&F powder coated (thickness of powder coating not less than 50 micron) Anodised Aluminium frame for doors, windows, ventilators with one or more rebates including jointing cleat for fixing etc. complete all as specified and directed.

S&F factory made Solid PVC door frame of size 60mmx30mm made out of solid PVC foam with homogeneous fine cellular structure having smooth outer integral skin with suitable metal stiffner and fixed with 100x8 sheet metal CSK screws complete all as specified and directed. (Note :- Door frame shall be water proof, termite proof, elegant and should have excellent screws holding strength to fix hinges and hold doors properly for a long life.)

S&F Factory made soild PVC profiled panel door shutter 28mm thick with integral skin as frame & 3mm thick high pressure compact laminate on both side of approved colour as infill, with 'C type Gl or 40 x 20 x19 of MS pipe as stiffner & supplying & fixing in frame at site as per specifications & drawing.

S&F 100mm size mild steel bright finish butt hinges, medium weight and fixed with screws complete all as specified and directed.

S&F 150mm long Aluminium, anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

S&F 150mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm size extruded aluminum alloy handles, fabricated type, anodised complete all as specified and directed.

S&F 100mm long aluminum anodised, hasp and staple, safety type, with mild steel hinge pin including bolts to hinge plate and fixed with screws complete all as specified and directed.

S&F in repair 25mm dia stainless steel fancy type curtain rods of approved quality including latoo/bracket/junctions /wall to wall of best quality as approved by Engineer-in-Charge.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 300mm long, mild steel, ordinary rat tail rod pattern springs including including roller and roller plate complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed complete all as specified and directed.

S&F 150mm floor door stopper of aluminium alloy body and tongue anodised, with hard drawn steel spring, fixed in floor complete all as specified and directed.

S&F kitchen PVC cabinet in required sizes at site made out of 18mm thick one side decorative lamination & other side balancing lamination sheet consisting of carcass 18mm thick pvc sheet & provision of shutters made out of 18mm thick one side decorative laminated PVC sheet all required brackets, screws etc. The panels shall be fabricated using adhesive and screws where ever required. All the edges shall be covered with 2mm thick edge bonding tape or 90 degree edge bent finish including all necessary fittings as per site requirement and as per make and specification mentioned as per drawing and all as specified .

S & F auto concealed hinges SS size 103mmx64mmx28mm suitable for cabinet and wardrobe complete all as specified

S&F Magnet ball catches with 8mm dia steel ball and brass body and striking plate for cup board/cabinet shutters complete all as specified and directed

M&L for 4.8 mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area exc 0.5 Sqm in each pane complete all as specified and directed.

M&L for 5.5mm thick sheet glass, ordinary quality and glazing with oil putty or wooden beads in square, area exc 0.5 Sqm in each pane complete all as specified and directed.

S&F 4mm thick figured glass pin head type and glazing with oil putty in square not exc 0.5 sqm in each pane, complete all as specified and directed

S&F 4mm thick sheet glass ordinary quality of glazing with oil putty or wooden beads in squire not exc 0.5 sqm each panes as directed.

Taking down steel gate of any size and refixing in same opening complete all as specified and directed

M&L for hollow stainless steel letters, bright finished, made out of 1mm thick 304 grade Salem stainless steel sheet, approx size 50 to 70mm wide and 350 to 450mm high with suitable fixing arrangement and fixed to wall to match existing complete all as specified and directed. (NOTE: Each letter shall be measured and paid separetly.)

M&L for premium quality joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in floors etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer in cement mortar 1:6 and dismantling of existing tiles complete all as specified and directed.

M&L for premium quality joint free non skid ceramic tiles, coloured, superior quality, 7 to 8mm thick, (square/ rectangular), area of each tiles exceeding 0.18 Sqm but not exceeding 0.38 Sqm, in skirting etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick screed bed or bedding layer in cement mortar 1:4 and dismantling of existing tiles complete all as specified and directed.

M&L for joint free glazed coloured DIGITAL GLOSSY tiles, superior quality of size 300 x 450 x 7mm thick/300 x 600 x 7mm thick, in vertical surfaces etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in cement mortar 1:4 and dismantling of existing tiles complete all as specified and directed.

S&F vitrified tiles, dark shade, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm but n exc 1 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed in CM 1:6 and dismantling of existing tiles complete all as specified and directed.

S&F vitrified tiles, coloured, superior quality 10mm thick (square/ rectangular) polished, area of each tiles exceeding 0.42 Sqm but n exc 1 Sqm, in vertical surfaces etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick rendering in CM 1:4 and dismantling of existing tiles complete all as specified and directed.

S & F Granite 20mm thick of any type (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including 15mm thick screed in CM 1:4 complete all as specified and directed

S&F Exterior finish floor tiles of appproved size 10 to 12mm thick, superior quality, approved shade, set and jointed in neat cement slurry and pointed in white or coloured cement to match as in floor including 20mm thick screed bed in cement mortar 1:4 complete all as specified and directed.

S&F in repair Gypsum Board 12mm thick (textured finish), white prelaminated sett embossed reinforced designer ceiling boards of approved texture at all height laid on hot dipped GI imposed grid with 24mm wide T sec exposed flanges which shall be pestered coated white. The frame work shall comprise of main runner made from 0.33 mm thick GI sheet of size 24x32x300mm and spaced at 1200 mm C/C securely fixed to the structural soffits by approved hangers at 1200mm c/c. Hangers of GI wire 4mm dia to be fixed by approved rawl plug, screw etc. The last hanger at the end if each main runner shall not be greater than 450mm from adjacent wall, flush fitting of 1200mm long cross tee (with double stitching) to be interlocked between main runner at 600mm C/C to form 1200x 600 mm modules cross tee longer than 600mm to be supported independently 1200x600 dodules formed by fitting 600mm long cross tee centrally between the 1200mm cross tee. Tee perimeter wall angle shall be made of 0.45mm thick GS sheet of size 19x19mm and 300mm long of white colour all as per manufacturers instructions complete all as specified and directed.

M&L for two coats of cement base paint over one coat of primer on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

M&L for two coats of oil bound distemper over one coat of primer and 1mm thick layer of wall care putty on newly plastered surfaces of wall including preparation of surfaces complete all as specified and directed.

Complete removal of existing treatment of wall and M&L for two coats of oil bound distemper on previously treated plastered surfaces of wall over one coat of primer and 1mm thick layer of wall care putty including preparation of surfaces complete all as specified and directed.

M&L for preparation of new ceiling surface and applying three coats of white wash complete all as specified and directed.

M&L for preparation of old ceiling surfaces and applying two coats of white wash complete all as specified and directed.

M & L complete removal of existing treatment on walls (any number of layers) by scrapping with steel scrappers or any other means, including filling depression of scrapped surfaces with putty and applying two coats of cement base paint over a coat of primer including preparation of surfaces complete all as specified and directed.

M&L PCC 1:2:4 type B-0 (using 12.5mm graded stone aggregate) as in roof kerbs /benching or mud stops, rounded, chamfered on edges including necessary use and waste of form work etc all as specified and directed.

M&L water proofing treatment to roof surfaces with polymeric water proofing membrane with 3mm thick APP membrane having non woven polyester matt at center core and covered with high quality polymeric asphalitic protected with thermo fusible HMHDPE ( high molecular high density polyethylene) film on both side and overlaps 100mm and sealed by flame and 150mm end overlaps, sealing all overlaps complete by flame including treatment at all junctions and corners. The membrane shall be torched into grooves on vertical plains and grooves sealed with cement mortar 1:3, and applying a coat of hot oil based bitumen primer@ 0.40 ltr/sqm, then un-rolled & bonded membrane completely to substrata and over laps(10cm) sealed by flame and over membrane and applying two coats of aluminium paint on membrane @ 0.10 Kg/Sqm (each coat) complete all as specified and directed.

M&L preparation of new wood or wood based surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

M&L preparation of new steel surface of any description exceeding 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red oxide primer complete all as specified and directed.

M&L preparation of old steel surface of any description exceeding 10cm width or girth and applying two coats of synthetic enamel paint complete all as specified and directed.

Supply, fixing, laying & testing 15 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

Supply, fixing, laying & testing 20 mm dia (Nominal bore) galvanised iron water tubing 'medium grade' with and including all GI fittings such as flanges, unions, reducer sockets, socket reducing bends, elbows, tee, checknuts, caps, plugs etc. fixed complete to walls and ceilings or laid in floors and testing including taking down existing GI tubing complete all as specified and directed.

S&F 15 mm bore CP brass centre hole basin mixture quarter turn with U shape round casted spout with 450mm long braided hoses fixed to GI pipe complete all as specified and directed. Make ESSCO Jaquar Cat NoTQT516A/Hindware Cat No F280009CP

S&F Brass Chromium plated hot & cold water wall mixer 2in1 system wall unit with over head shower arrangement with hot and cold valves cast copper alloy heavy duty screwed down for iron pipe and fixed complete all as specified . Make ESSCO Jaquar Cat NoTQT517B/Hindware Cat No F280018CP/Parryware G3316A1

S&F in repair 15 mm bore stop valves/angle valve copper alloy, fancy type,chromium plated half turn with screwed down, high pressure with crutch or butterfly handle screwed both ends fixed to GI pipe complete all as specified and directed.

Supply & Fixing in repair 15mm bore PVC connection 450mm long with brass coupling and washer complete all as specified.

Supply & Fixing in repair copper alloy long body bib taps chromium plated suitable for 15mm bore pipe with captain head complete all as specified.

Supply & Fixing in repair gun metal gate valve screwed both ends to 20mm bore pipe complete all as specified.

Supply & Fixing in repair CP shower rose fancy type 125mm thick with or without swivel joints any size including fixed to steel pipe or union complete all as specified.

S&F in repairs 1000 litres capacity rotational molded polyethylene water storage tanks (cylindrical vertical with closed top), hoisted and fixed in position complete all as specified in SSR Part-I including ball valve high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe or brass ferrule and fixed suitable for 20mm bore pipe (Min weight 210gms) complete all as specified.

Supply and fixing in repairs of vitreous china wash hand basin flat back size 550x400mm and including brackets and CP waste coupling 32mm dia and PVC waste pipe,complete all as specified and directed.

S&F Vitreous China squatting pan, 'Orissa pattern', size 580x440mm, white, with integral foot rests including PVC 'P' or 'S' trap, excluding flushing cistern and flush pipe, including connection to trap and flushing pipe etc. and making good to floor complete all as specified and directed.

S&F PVC valveless, syphonic action type, low level, flushing cistern of 10 lit capacity, white, with inlet, ball valve, float valve and handle including bracket, rubber cone and flush pipe etc. and connection to pipes complete all as specified and directed.

Supply & fix in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed

Supply & fix in repair CP Brass Tabular Towel Rail, 20mm dia D type 60cm long between flanges complete all as specified and directed

S&F glass corner shelves fancy type 6mm thick 250x250mm size and fixed over CP brass brackets all as specified and directed by Engineer-in-charge.

Supply and fixed in repair 75 mm dia PVC floor trap with CP grating including jointing to waste pipe fixed in cement concrete complete all as specified and directed

S&F PVC (SWR) pipes in any length with rubber ring joints fixed to wall 110 mm bore complete all as specified and directed

S&Fin repair PVC (SWR) pipes in any length with rubber ring joints fixed to wall 75 mm bore complete all as specified and directed

S&F PVC bends 110 mm bore fixed and jointed with solvent complete all as specified and directed.

S&F PVC bends 75 mm bore fixed and jointed with solvent complete all as specified and directed.

Supply & Fixing in repair sink without drainage board size 560x410x200 mm made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes pipe & coupling etc incl bedding in cement mortar to draft wall or cantilever brackets and connection union to pipe all as specified

Taking down copper/ aluminium point wiring (light, fan, socket or power) complete including fixture and fittings such as switches, ceiling roses, pendants, regulators, sockets, light fittings etc. removing materials to store for keeping in safe custody or for taking credit and making good disturbed surfaces of walls, floors etc. to match the existing complete all as specified and directed. NOTE: Credit for this items shall be made as per conditions separately.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed terminal switch boxes not less than 1.6mm thick of reqd size factory made duly painted inside and outside with one coat red oxide primer, 3mm thick plastic laminated bakelite sheet top cover (ISI Marked) fitted with chromium plated brass screws & washers complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 94 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 94 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item no 94 above but for one bell point controlled by one bell push.

All as per item no 94 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F Switch piano, flush type, single pole, one way 15/16 Amp 230 Volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 5/6 Amp, 230 volts complete all as specified and directed.

S&F socket outlet, flush type, single pole, multipurpose 2 in 1, 5 pin 15/16 Amp, 230 volts complete all as specified and directed.

S&F bell push switch piano, flush type, single pole, one way 5/6 Amp 230 Volts complete all as specified and directed.

S&F call bell (Ding dong) AC 230 Volt complete all as specified and directed.

S&F ceiling rose, 3 terminal, PVC/ Polycarbonate, insulated body, surface bakelite sheet 63.50mm dia complete all as specified and directed.

S&F Lamp holder PVC/ Polycarbonate type with back plate suitable for batten fittings complete all as specified and directed.

S&F ceiling fan regulator, electronic, rotary step up socket type, 230 volts suitable for 1200/1400 mm sweep ceiling fan including necessary connection complete all as specified and directed.

M&L for point wiring complete for one light point or one fan point controlled by one, one way 5 Amp modular switch with PVC (FRLS) insulated unsheathed multistranded copper conductor of size 1.50 sqmm nominal cross sectional area single core drawn in and including 20mm dia 'medium grade' PVC concealed conduits ISI marked and fittings, including pressed steel concealed GI terminal switch boxes not less than 1.6mm thick of reqd size factory made complete including 1.50 sqmm nominal cross sectional area PVC(FRLS) insulated unsheathed multistranded copper conductor green as earth wire connected to earth dolly with all accessories complete all as specified and directed.

All as per item no 108 above but for one bell point controlled by one bell push.

All as per item no 108 above but for one 5 pin 5 Amp socket outlet point on an independent board.

All as per item no 108 above but for one 5 pin 5 Amp socket outlet point on the same board with other switch.

All as per item no 108 above but for one 6 pin 15/16 amps socket outlet point on an independent board with cables of size 2.50sqmm and green colour earth cable of size 2.50sqmm.

S&F Modular switch 1 way 6A, 1 module complete all as specified and directed.

S&F Modular Bell push 6A 1 module complete all as specified and directed.

S&F Modular switch 1 way 16A, 1 module complete all as specified and directed.

S&F Socket, 6A - 2/3 pin combined 2 module complete all as specified and directed.

S&F Socket 6A/16A - 2/3 pin combined 2 module complete all as specified and directed.

S & F Fan step regulator, 120W - 2 module (Modular) complete all as specified and directed.

S & F white cover plate with frame modular type of 03 module complete all as specified and directed.

S & F white cover plate with frame modular type of 04 module complete all as specified and directed.

S & F white cover plate with frame modular type of 06 module complete all as specified and directed.

S & F white cover plate with frame modular type of 08 module complete all as specified and directed.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 4sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

S&F sub main wiring with two single core PVC insulated (FRLS) unsheathed multistranded copper conductor of size 6sqmm nominal cross sectional area and one run of 4sqmm nominal cross sectional area PVC insulated (FRLS) unsheathed multistranded copper conductor green colour as continuous earth wire drawn in and including 25mm dia 'medium grade' PVC concealed conduits (ISI marked) and fittings complete all as specified and directed. NOTE:- One unit length shall measured as two run of main wire and one run of conduit & earth wire.

Supply and Fixing wall/surface mounting luminaires integrated LED Batten 22 W, 6000 K,110 lumens/watt , 230V with extruded Aluminium housing 4 feet long with frosted PMMA/PC diffuser & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as specified and directed by Engr-in-charge. Make Phillips Smart brite cat no BN 021 LED 22S 6500 PSU GR/SI or/Havells Endura linear neo cat no enduralinear neo BS22WLED865SPCWH/ Bajaj LED batten BCLAB 20W WH LED P

S&F in repair LED Building security light 24/25 Watt with high power LED source (>110lumen/watt) PDC housing, IP65 and IK 07 with 4 KV inbuilt surge protection potted driver including Electrical connection with PVC three core copper flexible wire & all necessary fixing accessories such as bracket of GI pipe light grade 40 mm dia 0.60 mtr long bend to shape as per suitable size along with all accessories, fixed on wall including bolts & nuts. Make philips Green line smart cat noBRP042 LED 25 CW R1 S1 PSU GR/ Bajaj Edge nxt LED cat no ENXT P 24L WH CR PC SD/ Eveready Mini might cat no LED SL025157-02

Supply and fixing wall/surface mounting luminaires (Mirror Light) integrated LED Batten( 2 feet) 10/12 W, 6500 K, 230V ,100 lumens/watt,with extruded aluminium housing & integrated electronic driver complete including Electrical connection with PVC three core copper flexible wire & all necessary fixing arrangements all as per specified and directed by Engr-in-charge.Make:Phillips smart brite cat no BN 021 LED 12S 6500/4000 PSU GR/SI or/Havells Endura linear neo cat no enduralinear neo BS10WLED865SPCWH/ HPL Neptune plus 10 w HLPT51510CW

M & L for earthing complete with galvanized steel earth plate electrode 600x600x6.3 mm thick, burried directly in ground (earth pit not less than 2.25 mtr deep below ground level) with top edge of the plate not less 1.5 mtr deep below normal ground level connected to galvanized earth lead wire 4.0 mm dia by means of nut, bolts, check nut & washer of galvanized iron or of steel, earth lead protected by 15 mm dia GI pipe light grade, watering pipe 20 mm dia GI light grade, GI wire mesh funnel alternate layer of char coal and salt, PCC chamber and including RCC cover including all necessary excavation & earth work, earth wire connected to main switch board, testing the earthing after completion all as specified and shown in electric plate No 3 of MES SSR Part-I 2009 print and as directed .

S&F in repair of recessed type square LED 12W downlighter of size 160x160mm as required complete all as per specified and directed. Make: Havells Enduraneo surface DLS15WLED857S/ Philips sleek surface cat no. SM260 & SM261 (Square)/ Bajaj Sleek surface LED BGSLO Sleek Surface 15W WH SQ.

S & F in repairs Flexion 5 mtr LED strip 22 W, 3000K/6000K as required on site with electronic driver with wide viewing angle for good light distribution, easy to install complete all as specified and directed. Make :-Havells LHEHCPP7IN1W022 Driver LSSLNW0135/ Philips LED Strip Sky cove LED strip

S&Fin replacement of sheet metal enclosures with socket plug top and MCBs with a two pin and earth plug and socket complete with one single pole MCB 20 Amps all as per specified and directed Make Anchor/ Havells/C&S

S&F sheet metal enclosure for MCB DB double door type, triple pole and neutral 4 way, 415Volts with 200 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F sheet metal enclosure for MCB DB double door type, single pole and neutral 8 way, 240Volts with 100/125 Amps rated bus bar of suitable size plate and common neutral link, epoxy powder coated, factory made complete without MCB and with enclosure blank plates for unused way complete all as specified and directed.

S&F MCB, triple pole & neutral 40 to 63 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole 6 to 32 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

S&F MCB, single pole & neutral 32/40 Amp, 240 volts, 10 KA breaking capacity, 'C' curve complete all as specified and directed.

Taking down ceiling/exhaust fan including fixture and fittings from ceiling/wall and refixing the same after cleaning and painting and making connection with new PVC insulated and sheathed PVC cable with copper conductor 1.5Sqmm three core complete all as specified and directed.

Taking down electric energy meter including fixture and fittings and refixing the same after cleaning and making connection complete all as specified and directed.

M/S Reliance Construction

rajan construction

Spectrum Enterprises