Construction of store for kitchen at Udaygiri Hostel NIT Hamirpur Civil and Electrical work

Amount

Cutting in earth work in excavation by mechanical means (Hydraulic excavator)/manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto all leads and lifts , as directed by Engineer-in-charge. All kinds of soil,including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed by the Engineer-in -charge, All kinds of soil,with in all leads, including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : cement concrete 1:4:8 (1 Cement : 4 coarse sand : 8 graded stone aggregate 40 mm nominal size)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing from work in centering and shuttering including strutting, propping etc. and removal of form for all heights including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Lintels, beams, plinth beams, girders, bressumers and cantilevers

Columns, Pillars, Piers, Abutments, Posts and Struts

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level,cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with cement concrete 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III) : 3 graded stone aggregate 20 mm nominal size) including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete. Thermo-Mechanically Treated bars of grade Fe-500 D or more including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing up to floor five level precast cement concrete solid block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying 12 mm cement plaster of mix 1:4 (1 cement: 4 fine sand) including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying15 mm cement plaster on the rough side of single or half brick wall 1:6 (1 cement: 6 fine sand)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and laying Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+ 0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete Ridges plain (500 - 600mm)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing Gl Clip in Metal Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the perimeter of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of Gl steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. All sections to be galvanized @ 120 gms/sqm (both side inclusive), fixing with clip in tiles into spring T with GI Metal Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ sqm (both sides inclusive) and electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing ISI marked flush door shutters conforming to IS : 2202 (Part I) decorative type, core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt hinges with necessary screws including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing glazed shutters for doors, windows and clerestory windows using 4 mm thick float glass panes, including ISI marked M.S. pressed butt hinges bright finished of required size with necessary screws. Second class teak wood, 35 mm thick, including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete, 300x16 mm, including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than gradeAC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Distempering with oil bound premium quality washable distemper of approved brand of Asian/Nerolac/JK PrimaxX/ICI Dulux make and manufacture on old work with one or more additional coats to give an even shade including entire carriage of material in all leads, lifts, height and cost of all incidantals.

Finishing walls with Acrylic Smooth exterior paint of Asian (Apex/ICI Dulux (Weather Shield/Nerolac (Excel)/JK PrimaxX make with Silicone additives required shade New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Painting with synthetic enamel paint ofAsian/Berger/JK PrimaxX/Nerolac make of approved brand on wood/steel based surfaces and manufacture to approved brand and manufacture to give an even shade Two or more coats on new work including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS PVC insulated copper conductor single core cable etc. as required including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Group B

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FR PVC insulated copper conductor, single core cable of Havells/Plaza/Finolex make in surface/ recessed medium class PVC conduit as required including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

2 X 1.5sq. mm + 1 X 1.5 sq. mm earth wire

2 X 4 sq. mm + 1 X 4 sq. mm earth wire

Supplying and fixing suitable size GI box with modular plate and cover in front on surface or in recess, including providing and fixing 6 pin 5/6 & 15/16 A modular socket outlet and 15/16 A modular switch,of Legrand-Myrius/Schneider-ZENcelo / MK-Blenze/Cabtree Murano/Indo Asian make. connections etc. as required including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying and fixing 12 way, double door single pole and neutral,sheet steel, MCB distribution board, 240 V, on surface/ recess,complete with tinned copper bus bar, neutral bus bar, earth bar, din bar, interconnections, powder painted including earthing etc. as required. (But without MCB/RCCB/Isolator) including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying and fixing 5 amps to 32 amps rating, 240 volts single pole,C curve, miniature circuit breaker suitable for inductive load in the existing MCB DB complete with connections, testing and commissioning etc. as required of Legrand-DX3/Schneider-Acti9/Siemens-Betagard/Hager/Indo Asian make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying and fixing following rating, double pole,40 Amps, 240 V,isolator in the existing MCB DB complete with connections,testing and commissioning etc. as required including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying of exhaust fan of following sizes as required of Usha/Crompton/Havells make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Exhaust Fan, Light duty, (Domestic) 300 mm sweep

Supplying and fixing following rating, Double pole, 230 volts, 40 Amps, EL+MCB with overload protection (RCBO), having a sensitivity current upto 300 milliamperes in the existing MCB DB complete with connections, testing and commissioning etc of Legrand make. as required and directed by Engineer-in-Charge of Legrand-DX3/Schneider-Acti9/Siemens-Betagard /Hager/Indo Asian make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying and fixing Electronic fan regulator step type, socket type (Deluxe) Anchor or equivalant make as approved by Engineer-in-charge including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing, Installation, testing and commissioning of ceiling fan without regulator 5 star rating , including wiring the down rods of standard length (up to 30 cm) with 16/0.20 mm twin twisted flexible, cotton braided, copper cable, including providing and fixing phenolic laminated sheet cover on the fan box and earthing etc. as required:- Usha/Crompton /Bajaj make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Supplying of LED batten 4 ft for surface anodized extruded aluminium housing high transmissitivity diffuser and high lumen output 20 watt complete of Bajaj/Philips/Crompton make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

Providing ,laying ,commissioning of 4 core 16 sq mm armoured aluminium cable underground/surface as required at site complete in all respect of Havells/KEI/Plaza make including entire carriage of material with in all leads, lifts, heights and cost of all other incidentals.

RITESH SOOD

Himachal Techno Engineers