Construction of new Beer Bar Parlour and additional Arrival Toilet at VSI Airport, Port Blair

Amount

Providing and fixing up to floor five level precast cement concrete hollow block, including hoisting and setting in position with cement mortar 1:3 (1 cement : 3 coarse sand), cost of required centering, shuttering complete. (a) 1:1½:3 (1 Cement: 1½ coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) .

12 mm cement plaster of mix : 1:6 (1 cement: 6 fine sand)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 fine sand)

Providing and laying Vitrified tiles in different sizes (thickness to be specified by manufacturer), with water absorption less than 0.08 % and conforming to I.S. 15622, of approved make, in all colours & shade, in skirting, riser of steps, over 12 mm thick bed of cement mortar 1:3 (1 cement: 3 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joint with white cement & matching pigments etc. complete. (a) Size of Tile 300 x 450 mm

Providing and laying vitrified floor tiles (Glossy or matt finish as decided by EIC) in different sizes thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. (a) Size of Tile 600 x 600 mm

Providing and fixing false ceiling at all height including providing and fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : (a) 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : (a) 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Wall painting with acrylic emulsion paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing and Fixing Soap dispenser of Jaguar (ACN-1135N) or Equivalent make with Glass Bottle. All complete as per instruction of EIC.

Providing and Fixing health Faucet of Jaguar (ALD-CHR - 585) or Equivalent make cast copper alloy fancy type chromium plated with stand and flexible pipe. All complete as per instruction of EIC.

Providing and fixing toilet paper holder of Jaguar (ACN-1151N) or Equivalent make: C.P. Brass All complete as per instruction of EIC.

Providing and fixing Vitreous China oval countertop wash basin of approved make and colour of size not less than 500 x 400 x 200 mm with single 15 mm CP. brass pillar tap of approved make with fixing accessories like coupling etc. all complete as per direction of Engineer-in-charge ( The brand and colour preferably of dark shade and pillar tap brand and type will be decided by Engineer-In-Charge).

Providing and fixing wall mounted vitreous china pedestal type water closet of approved make and colour (European type) "S" or "P" with seat and lid, 6 litre (Double push) low level wall hung P.V.C flushing cistern of approved make with drainage l-bend with gasket (CNS-WHT-207) or Equivalent make with stainless steel fittings & brackets, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, cutting and making good the walls and floors wherever required: W.C. pan with white solid plastic seat and lid :( The brand and colour preferably of dark shade will be decided by Engineer-In-Charge).

Providing and fixing unplasticised PVC connection pipe with brass unions: 60 cm length 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer , geyser points, bib cock , stop cap, CP Cap and Nipple etc. of approved quality conforming to IS:8931 15 mm nominal bore.

Providing and fixing C.P. brass angle valve for basin mixer , geyser points, bib cock , stop cap, CP Cap and Nipple etc. of approved quality conforming to IS:8931 25 mm nominal bore.

Providing and fixing mirror of superior glass (of approved quality) and of required shape and size with stainless steel frame of approved make and shade with hard backing material or fixed with stainless steel studs etc. complete as per direction of Engineer in Charge

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (a) 20 mm nominal outer dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. (a) 25 mm nominal outer dia Pipes

Bharat Udyog