PROVN OF JAFRI WALL AND DRAINAGE AND CERTAIN ADDITION/ALERATION WORK AT CHITNIS ENCLAVE UNDER GE BRICHGUNJ PORT BLAIR.

Amount

Surface excavation not exceeding 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches, not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, etc or not exceeding 10 Sqm on plan and not exceeding 1.5m in depth for shafts, cesspits, manholes, pier holes, etc and getting out in soft/loose soil complete all as specified and directed.

M&L for PCC 1: 4:8 type D-2 (using 40mm garded stone agg ) as in foundation as filling mass concrete complete all as specified and directed.

M & L for RCC- M - 30 Design Mix (using 20mm graded stone aggregate) as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L Reinforced cement concrete (design mix M-30 grade using 20mm graded stone aggregate) above top of footings including attached pilasters and buttresses complete all as specified and directed.

M & L for RCC- M -30 Design Mix (using 20mm graded stone aggregate) as in columns, pillars, piers,posts and struts complete all as specified and directed.

M & L for RCC- M -30 Design Mix (using 20mm graded stone aggregate) as in beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

Returning, filling in excavated approved soil, including spreading, levelling, watering and well ramming in layers not exceeding 25cm each complete all as specified and directed.

Removing excavated soil to a distance not exceeding 50m and depositing where directed. at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Use & waste of Form work to sides of concrete foundations, footings, bases of columns, sides & soffits of foundation and plinth beams and similar work for fair finished flat surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides of square or rectangular columns, pillars, posts and struts for fair finished surfaces of concrete complete all as specified and directed.

Use & waste of Form work to sides & soffits of lintels over 1.5m clear span, floor or roof beams, cantilevers, etc for fair finished flat surfaces of concrete complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 6 to 8mm dia as reinforcement for concrete, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

S&F Mild steel TMT bars 5 to 10mm dia in stirrups, spacers and binders, cut to length, bent to shape required, including cranking, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia complete all as specified and directed.

M&L Precast Cement Concrete Block Masonry with Solid Block, exc 10cm in width in type C-1, 1:3:6 (using 20mm graded stone aggregate) set in CM (1:6) complete all as specified and directed.

M&L for Providing precast RCC Jali 25mm thick RCC 1:2:4 type B-0 ( Using 12.5mm graded stone agg inclu all necessary form workbuilt in CM 1:4 complete all as specified and directed.

M&L 15mm thick rendering in two layers of 10mm thick backing coat in CM 1:6 and 5mm thick floating coat in CM 1:4 mixed with water proofing compound on all external wall surfaces finished even and smooth without using extra cement complete all as specified and directed. (Note : Water proofing compound shall be measured and paid seperately)

M& L for Finishing walls with Acrylic smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm) etc complete all as specified and as directed. (Make Apex Ultima)

M&L for precast man holes cover slab with 1:2:4 type B1 using 20mm graded stone aggregate set in CM 1:4 incl cost of use and waste of clean sawn wooden form work but excl cost of reinforcement complete all as specified and directed.

Dismantling of Dismantling boarding, any description, fixed in any position with nails and any thickness, fixed in any position complete all as specified and directed.

Post ConstructionTreatment of soil under existing floors using emulsion @ one litre per hole, 300mm apart including drilling and plugging 12mm dia holes with cement mortar 1:2 (1 cement: 2 coarse sand) to match the existing floors complete all as specified and directed.

S&F Butt hinges, medium weight coldrolled mild steel and fixed 50mm size complete all as specified and directed.

Supply & Fixing mild steel 40mm dia Brass polished cupboard knobs fixed with nut, screw and washer off complete all as specified and directed.

S & F 24 Inches (Maximum) Telescopic Drawer Channel Stainless Steel | Rust Free | 600mm Ball Bearing Soundless Office Table Drawer Slides Pack of 1 Set (2 pcs) complete all as specified and directed.

S & F 30 mm width of flap Continous (Piano) hinges, mild steel, bright finish or electrogalvanised complete all as specified and directed.

S&F 75mm size hasp and staple, safety type aluminium anodised with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

S & F Aluminium anodised (minimum anodisation is 15 microns) Door / window / Ventilator/partition frames and shutters (02 Nos glazed & gauzed), side hung type, without sash bars, standard aluminium grills, necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, handles, locking arrangement etc, complete with standard aluminium sections, all as specified and as directed by Engineer-in-charge. (Aluminium section shall be of make Jindal/Hindalco/ Indalco). (Note:- Weight of various Aluminium sections shall only be considered for measurement for payment. However cost of rubber packing given in the item shall be deemed to be included in the rate quoted. Glass panels, prelaminated particle boards, aluminium wire cloth as applicable will be measured and paid separately as supplied only).

S&F Aluminium anodised barrel tower bolt of extruded section of size 150mm long complete all as specified and directed.

S&F 150mm long extruded aluminium alloy anodised handles fabricated type, anodised complete all as specified and directed.

S&F 75mm long extruded aluminium alloy anodised handles fabricated type, anodised complete all as specified and directed.

S&F 100 Butt hinges extruded aluminium alloy, anodised. With galvanished mild steel hinge pin , anodised and fixed type B-21 complete all as specified and directed.

S&F sheet glass ordinary Quality and glazing with oil putty in square exc 0.5 sqm in each pane of thickness 6.3 mm complete all as specified and directed.

M&L for 12-16 mm thick MDF board of any Colour to fixed with screws to timber frame work. Or Fixed wirh aluminiun frame work to the fixing Clips all as specified and as directed (Note :- Colour as finalised by GE)

M&L for 12 mm thick prelaminated particle board to fixed in repair interior grade prelaminated both side with decorative choice lamination fixed with screws to timber frame work complete all as specified and directed.

S&F Aluminium composite panel sheet of 3mm to 4mm thick, fixed on aluminium frame work with plastic strips (double sided sticker) of suitable size of varying thickness of 10mm to 30mm applying adhesive over aluminium sections for fixing composite panel and fixed with screws. The joints of panels shall be filled with weather proof sealant for required portion, complete all as specified and as directed.

M/s Karbhagam Sales Agency

Nirman Construction Company

DEEPAK AGENCIES

P Babu

RS ENGINEERING WORK

M/s Saina Enterprises

RPG AND COMPANY