CONSTR OF 01 X 10-12 MEN LIVING, WATER STORAGE TANKS FOR TROOPS, GENERAL SHED WITH INDIAN STANDARD MEDIUM BEAM AND TRG OPEN SHED WITH INDIAN STANDARD MEDIUM BEAM (ISMB) IN THE AOR OF AGE B/R-II UNDER GE 969 EWS

Amount

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25 cm in hard/dense soil complete all as specified.

Excavating over areas, n exc 1.5 m deep and getting out in hard/dense soil complete all as specified.

Removing excavated material soil n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point complete all as specified.

M&L for hardcore of broken stone or boulders of gauge n exc. 63 mm , deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M&L for cement concrete 1:4:8, type D-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified.

M&L for cement concrete 1:2:4, type B-2 (using 40mm graded stone aggregate) as in foundation, filling and mass concrete complete all as specified.

M&L for 100mm thick cement concrete 1:4:8, type D- 2 (using 40mm graded stone aggregate) as in sub base of flooring complete all as specified.

M&L for 100mm thick cement concrete 1:2:4, type B-1 (using 20mm graded stone aggregate) as in flooring and finishing the concrete surface even and smooth without using extra cement complete all as specified.

M&L for roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc confirming to Fe-290 (Gde E-165) complete all as specified.

M&L for rolled mild steel in joist, channel, angle, or tee sections, fixed independently, without connecting plates, etc. (cut to ordinary lengths i.e. within 20mm of the length indicated) confirming to Fe-290 (Gde E-165) complete all as specified.

M&L for 0.63mm thick galvanised, corrugated mild steel sheeting with two corrugations side lap, fixed with L type or J type or cranked hook bolts in roofs, walls etc. with grade of zinc coating 275 complete all as specified.

M&L for 0.80mm thick plain, galvanised, mild steel sheeting, in ridges, hips, valley gutters, drip and straight flashings (length and girth as fixed) with grade of zinc coating 275 complete all as specified.

M&L for preparation of new or previously untreated steel surface of any description (including on the surface of galvanised sheet), over 10cm in width or girth, not otherwise described and applying two coats of synthetic enamel paint over a coat of red oxide, zinc chrome primer complete all as specified.

M&L for forming Contraction (Dummy) joints 65mm deep x 10mm wide, filled with sealing compound Grade 'A' complete all as specified.

M&L for forming Construction joint 30mm deep x 10mm wide filled with sealing compound Grade 'A' complete all as specified.

S&F 5000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs etc, including tank nipples, fittings complete all as specified.

S&F 10000 litres capacity rotational moulded, triple layer polythene water storage tanks (cylindrical vertical with closed top) hoisting and fixed in position on roofs etc, including tank nipples, fittings complete all as specified.

S&F 25mm outer dia of 3-layer PP-R Polypropylene random copolymer concealed pipes SDR 7.4 (PN16) UV stabilized and antimicrobial fusion welded having thermal stability for hot & cold water supply including all PP-R plain & brass threaded polypropylene random fittings fixed complete to walls, ceilings or in floors etc. complete all as specified.

Supply and spreading clean dry sand in trenches for cushioning for cable protection complete all as specified and directed. Note: The punned down thickness shall only be measured.

Excavation in trenches n.exc 1.5m wide and 1.5m depth for foundation etc or for shaft well, cesspits etc n.exc on plan and n.exc 1.5m depth and getting out in hard/dense soil complete all as specified and directed

Excavation in trenches n.exc 1.5m wide and n.exc 1.5m depth for foundation, laying of cables etc and getting in soft/loose soil complete all as specified and directed.

Returning filling in including spreading levelling, watering and well ramming in layers n.exc 25cm all as specified and directed.

Supply and laying sub class 'B' bricks laid across the cable for cable protection complete all as specified and directed.

M&L for formwork to sides of pillars, posts, struts, piers, plinth beam columns and stanchions in rough finished surface of concrete at square complete all as specified.

M&L for RCC (Nominal Mix) 1:2:4 (using 20 mm graded stone aggregate) for foundation, including rafts, footings, foundation beams, plinth beams, bases for columns etc., basement slabs under reamed piles and mass concrete complete all as specified and directed.

M&L for factory solid Pre-cast cement concrete 1:3:6 type C1 (using 20mm graded stone aggregate) (vibrator made) mechanically pressed block masonry, exc. 10 cm in width and setting in cement mortar 1:6, complete all as specified and directed

M&L for rendering 15 mm thick in cement and sand mortar 1:4 on other than fair faces of brick work or cement concrete surfaces including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for preparation of plastered surface of wall and applying two coats of cement base paint on new surface complete all as specified.

N&L for 25mm thick cement concrete 1:2:4, type B-1 (using 20 mm graded stone aggregate) finished the surface even and fair without using extra cement complete all as specified and directed.

M&L verified ceramic tiles 10 mm thick (square/ rectangular) polished, area of each tiles not exceeding 0.36 sqm, set and jointed in neat cement slurry and pointed in white or coloured cement to match. including screed bed 15 mm thick in CM 1:4 complete all as specified and directed.

S&F for 50 mm thick wall panel made of 0.5 mm thick not dipped galvanized steel sheet on both side with 50 mm thick, layer of rigid etc free closed cell polyurethane foam with tongue and groove joint including cam lock system for interlocking fixed on base channel 30mmx36mmx1.25 mm thick density of form shall be 40 Kg/Cum (+- Kg/Cum) the panel shall be precoated as approved by GE complete all as specified and directed.

S&F for 40 mm thick puff insulated panel made of 0.5 mm thick on both side with 40 mm thick rigid polyurethane with tongue and groove joint interlocking for ceiling to be fixed with and both including inverted CRCA Tee section 50mmx50mm and 5 mm thick and L section of 50mmx50mm and 5 mm thick to roof trusses including handing aggargments complete all as specified and directed

S&F for sliding type three track aluminium window provided with top and side member 92mmx317mm and 1.5 mm thick (1.06 kg/Minimum weight) bottom three track rail shall be 90x31.75x1.5 mm (1.248 kg/RM) shutter shall of 40nnx31.75mm and 1.5 mm section (0.547 kg/RM weight) shutter shall be provided with handle and self locking arrangement interlocking style shall of 40mmx18mmx1045 mm (0.607 Kg/RM) panel shall be of 6 mm thick Clare grade 6/2 Rs. 1.3 mm polycarbonate shall the wince shall be fixed to wall panel as per standard practice two shutter shall glazed and one shutter shall be wire gauged of aperture 1.40 mm complete all as specified and directed.

S&F Flush shutters 30 mm with solid core construction, with block board core and plywood face panels, commercial type complete all as specified

S&F for steel work in tubular trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to IS 1161 1979 grade all as specified and directed by Engr-in-charge.

S&F pre-painted galvalume aluminium zinc coating Gl based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tanning screws complete all as specified

S&F pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified.

S&F mild steel plates, Fe-410 W (Gde-E250) quality B plain or chequered, 5 mm thick or over in thickness in available sizes complete all as specified and directed.

S&F of mild steel rag or lewis bolts, screwed one end, with hexagonal or square nuts and washers, the other end enlarged and jagged or lewised, nexc 30cm long complete all as specified and directed.

S&F Mild steel TMT bars 10mm dia and over, cut cranking, bending spirally for hooping for including mild steel wire (annealed) not less to length, bent to shape required, including columns, hooking ends and binding with and than 0.9mm dia or securing with clips complete all as specified and directed.

S&F Mild steel TMT bars 6mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified and directed.

M&L for providing 75 mm thick plain cement concrete 1:3:6, type C-2 (using 40mm graded stone aggregate) as in plinth protection complete all as specified and directed

S&F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for foxing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing complete all as specified and directed.

S&F 300mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, S cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

S&F 100mm long butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

S&F 150mm long aluminium handles, cast type, anodised complete all as specified and directed.

S&F 200mm long aluminium anodised, barrel tower bolts of extruded section and fixed complete all as specified and directed.

Supply and laying XLPE insulated PVC FRLS, armoured heavy duty electric cable with aluminium conductor, 1100 Volts grade, cross-sectional area, galvanized steel strip or wire armoured of size 16 Sqmm 2 core complete all as specified and directed.

Supply and laying GI tubing medium grade ISI marked complete with all necessary fittings of sizes 20mm bore in trenches complete all as specified and directed.

M&L for point wiring in PVC casing capping with 1.5 Sqmm size multi stranded FRLS copper conductor cable 1.5 Sqm including clamps, screws gutter/plug etc PVC unsheathed cable into and including wooden board with Bakelite sheet and PVC insulated FRLS cable of size 1.5 Sqmm as earth continuity conductor, One light point/fan point/ex fan point controlled by one 5 Amps switch one way complete all as specified and directed.

All as per ser item No 50 here-in-before but one 3 pin 5 Amps switch socket outlet on independent board

All as per ser item No 50 here-in-before but one 3 pin 5 Amps switch socket outlet on same board

M&L for point wiring in PVC casing capping with 2.5 Sqmm size multi stranded FRLS copper conductor cable including clamps, screws gutter/plug etc PVC unsheathed cable into and including wooden board with Bakelite sheet and PVC insulated fire retardant cable of size 2.5 Sqmm as earth continuity conductor complete all as specified and directed.

S&F switch piano flush type , single pole, one way 6 Amp 240 Volts, complete all as specified and directed. Note : Taking down of switches shall be included in taking down point wiring

S&F Flush type Socket outlet 6 Amps, complete all as specified and directed. Note : Taking down of socket outlet included in taking down point wiring

S&F switch socket combination 5 pin 15A flush type complete all as specified and directed.

S&F ceiling rose 3 terminal / PVC/ Polycarbonate, isolated body complete all as specified and directed.

S&F in repairs Lamp Holder, PVC/ Polycarbonate type with back plate suitable for batten fitting complete all as specified and directed.

S&F Distribution Board SPN 8 Way, Single door Complete all as specified and directed by Engr In Charge

S&F Amps rating 240V, 10KA 'C' curve miniature circuit breaker (MCB) of capacity SPN 32 Amps current carrying capacity in the MCB DB complete with connection testing and commissioning complete all as specified and directed.

S&F 240V, 10 KA 'B' curve (MCBs) of single poles and current carrying capacity 5 to 32 AMP, in the MCB DB Complete with connection testing and commissioning complete all as specified and directed.

S&F LED Lamp 15 W complete all as specified and directed. Make : Havells cat No. LHLDEREEMK8X015 or techno commercially equvialent in/ Philips / Bajaj/Crompton

S&F LED lights fitting 1x 20W, 220V, AC decorative box type with driver, holder including LED tube light connecting up with three core flexible copper conductor cable of suitable size from ceiling rose. complete all as specified and as specified and directed.

S&F LED light fitting 1x9W/1X10W bulkhead luminaires including LED light driver holder connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed by Engineer-in-charge.

M&L in repairs for Earthing complete with galvanized steel earth plate electrode 600mm x 600mm and 6 mm thick buried directly in ground (earth pit not less than 2.25 m deep below normal ground level) with top edge of the plate not less than 1.5 m below normal ground level connected to galvanized earth wire of 4 mm dia (up to 7.5 m in length from earth plate ) by means of bolts and nuts checknuts and washers of galvanized iron or steel all as specified and shown in electrical plate no.5 of SSR 2020 part I including necessary excavation and earth work in any type of soil PCC 1:3:6 type C1 chamber with RCC 1:2:4 type B1 40 mm thick cover with MS rod 6 mm dia at 150mm c/c in both ways as reinforcement, watering funnel, 20 mm dia light grade for protection of earth electrode, 20 mm dia GI pipe light grade for watering complete all as specified and as directed by Engineer in charge and tested on completion. Note : The rate is inclusive of necessary earth work, RFR and removal etc

M/S SHEIKH FEROOZ AHMAD (BID ID -3486599)

m/s mohd saleem and co (BID ID -3483402)