DUTY POST ALONG WITH VISITORS ROOM INCLUDING TOILET AND BATHROOM AT MADRAS REGIMENTAL CENTRE WELLINGTON NILGIRIS UNDER GE WELLINGTON

Amount

Earth work in excavation over areas by mechanical means (Hydraulic excavator) in any kind of soil (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50m and lift upto 1.5m, complete all as specified and directed.

Moorum/ red bajri filling in floors or pavings, laid in layers not exceeding 15 cm thick, spread, levelled and rammed including watering all as specified and directed.

Removing excavated soil/ material to a distance exceeeding 250m and not exceeding 500m and depositing where directed at a level not exceeding 1.5m above the starting point complete all as specified and directed.

Plain cement concrete 1:4:8 type D2 (using 40 mm graded stone aggregate) as in foundation, filling and mass concreting, complete all as specified and directed.

Reinforced cement concrete M-25 design mix using 20 mm graded stone aggregate as in foundations including rafts, footings, foundation beams, plinth beams, bases for columns etc basement slabs, under-reamed piles and mass concrete all as specified and directed.

Reinforced cement concrete (Design Mix M-25) using 20mm graded stone agregate in walls, retaining walls, basement walls, ballast wall and the like, any thickness, above top of footings including attached pilasters and buttresses all as specified and directed.

Use and waste of timber as in formwork to sides of concrete foundations, footings, base of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams, and similar work; vertical or to batter flat surface rough finished complete all as specified and directed.

Use and waste of formwork to faces of walls, retaining walls, abutments, parapets and staircase railings and similar work including attached pillaster, buttresses etc, vertical or batter for fair finished surfaces of concrete flat flat surfaces of concrete all as specified and directed.

Mild steel TMT bars 6 to 8mm dia cut to length, bent to shape required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips in stirrups, spacers, binders, etc complete all as specified and directed.

Mild steel TMT bars 10mm dia and over, cut to length, bent to shape as required including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips etc complete all as specified and directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed to walls with PVC clamp, complete all as specified and as directed.

Hand packing broken stone aggregate (any thickness) at back of walls over arches etc and raising (or lowering) to the required level all as specified and directed.

Returning, filling in including spreading, levelling, watering and well ramming in layers not exceeding 25cm thick each, complete all as specified and directed

Spreading levelling with approved soil obtained from excavation in layer not exceeding 25cm with soil well ramming with watering filling under floors all as specified and directed.

Preparing new surfaces of walls and applying two coats of cement wash with Portland cement slurry to a smooth bodied opaque finish complete all as specified and directed.

Forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'A' in 250 mm concrete slab complete all as specified and as directed.

Surface excavation not exceeding 30cm deep and averaging 15 cm deep and getting out in soft / loose soil complete all as specified and directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes,laying under ground cable etc. not exceeding 10 Sq m on plan and not exceeding 1.5 m in depth and getting out in soft/ loose soil complete all as specified and directed.

Use and waste of formwork to sides of pillars, posts, struts, piers, columns and stanchions with rough finished surface of concrete complete all as specified and directed.

Reinforced cement concrete M-25 design mix using 20 mm graded stone aggregate in columns, pillars, piers, posts and struts etc all as specified and directed. Note: Form work and reinforcement shall be measured and paid separately.

Use and waste of Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. Fair finished surfaces of concrete flat complete all as speicified and directed.

Reinforced cement concrete M-25 design mix using 20 mm graded stone aggregate in beams, cantilevers, bressummers, lintels over 1.5m span all as specified and directed.

Use and waste of formwork for fair finished surface to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) complete all as specified and directed

Reinforced cement concrete M-25 design mix using 20 mm graded stone aggregate for slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the likes complete all as specified and directed.

Pre-cast cement concrete block masnory with solid block exceeding 10cm in width and setting in cement mortar 1:6 type C1 1:3:6 using 20mm graded stone aggregate complete all as specified and directed

Rendering 10mm thick in cement mortar 1:6 on fair faces of brick work or concrete surfaces all as specified and directed.

Rendering 15mm thick cement mortar 1:6 on fair faces of brick work or concrete surfaces all as specified and as directed

Mild Steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders all as specified and as directed.

Plain cement concrete 1:4:8 type D-2 using 40mm graded stone aggregate as in sub base 100mm thick all as specified and directed.

Plain cement concrete 1:2:4 type B-1 using 20mm graded stone aggregate as in floor of 50mm thick all as specified and directed.

Coloured Non skid ceramic tiles matt finish 7 to 8mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including screed bed or bedding layer of mortar 15 mm thick in cement mortar 1:4 for laying floor finishes complete all as specified and as directed.

Coloured Glazed ceramic tiles in vertical surfaces 450 x 300 x 7mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 10mm thick plaster in cement mortar 1:3 on fair face of brick or concrete surface complete all as specified and as directed.

Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS Square tube, supplying and fixing in opening as per specification and drawing as mentioned in SSR all as specified and directed.

Factory made solid panel PVC door shutter 30mm (Stile) consisting of frame made out of M.S tubes for top and bottom rails M.S frame made up of tubes shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, panelling of plain colour PVC sheets to be fitted in the M.S frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement, supplying and fixing in the frame all as mentioned in SSR drawing all as specified and directed.

Steel ventilator with top hung shutter including hinges, steel peg stay, and applying two coat of Synethtic enamel paint over red oxide zinc primer complete all as specified and directed

Figured glass 4mm thick pin head type and glazing with oil putty in squares not exceeding 0.5Sq.m in each pane all as specified and directed.

Preparing surfaces, plastered or unplastered on new wall surface and applying three coats of white wash complete all as specified and directed.

Applying two coats of cement based paint, over a coat of alkali resistant primer including preparation of newly plastered surfaces complete all as specified and as directed.

Aluminium anodised, barrel tower bolts of extruded section 150 mm long all as specified and directed.

Aluminium butt hinges 100mm size all as specified and directed.

Aluminium handles, cast type, anodised 100 mm long complete all as specified and directed.

Health faucet (ABS Body) mild steel chromium plated suitable for 15mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete all as specified and directed.

PVC valveless, syphonic action type, flushing cistern, 10 litres capacity, white, with inlet, ball valve, float and handle including brackets complete all as specified and directed.

Vitreous china wash basin, white flat back size 550 X 400 mm including cutting for and pinning in ends of brackets or erecting stand but exclusive of taps, fixing of supply and waste pipe complete all as specified and directed.

32/40 mm bore PVC waste pipe suitable for wash hand basin/ Unirnal all as specified and directed.

Waste coupling 32 mm dia bore of PTMT (Half or full threaded) (Minimum weight 32mm-45gm/s) complete all as specified and as directed.

Pillar taps, fancy type, 15mm dia cast copper alloy, with capstan heads, chromium plated, screwed down high pressure, with long screwed shanks and fly nuts, screwed for iron pipe all as specified and directed.

Supply and fix PVC connections 15 mm size with PTMT nuts of length 750mm all as specified and directed.

Bib taps two way,15 mm, fancy type,cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule all as specified and as directed.

Angle cocks / Stop valves cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed fancy type chromium plated,15mm bore all as specified and directed.

Soap dish, chromium plated, 100 x 100 x 60 mm, fixed to wall with plugs with chromium plated screws complete all as specified and directed.

Brass chromium plated tubular towel rail, 20mm dia, D type, 60cm long between flanges all as specified and directed.

PVC (SWR) bend of any radius 75 mm dia complete all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia complete all as specified and as directed.

PVC (SWR) bend of any radius 110 mm dia with access door complete all as specified and as directed.

PVC (SWR) pipes 75mm bore single socketed, in any length with rubber ring joints, fixed to walls with clamp, complete all as specified and as directed.

PVC (SWR) 110mm dia pipe single socketed in any length, with rubber ring joint fixed to walls with clamps complete all as specified and directed.

PVC (SWR) pipes 75 mm dia single socketed in any length with rubber ring joints laid in trenches or in floors all as specified and as directed.

PVC (SWR) 110mm dia pipe single socketed in any length, with rubber ring joint fixed to walls with clamps complete all as specified and directed.

Hardcore of broken stone gauge not exceeding 63 mm, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface all as specified and directed.

75mm thick plain Cement concrete, 1:3:6, type C-1 using 20 mm graded stone aggregate as in plinth protection all as specified and directed.

Forming 12 mm thick expansion joints filled with pre-formed bituminous filler and top 30mm primed and sealed with sealing compound grade 'A' in 100 mm thick concrete slab complete all as specified and as directed.

Rotational moulded polyethylene water storage tank of capacity 500 Ltr (cylindrical vertical with closed top) three layers, hoisted and fixed in position with proper inlet and outlet connections all as specified and as directed

15 mm bore Tubes, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors all as specified and directed.

20 mm bore Tubes, 'Medium grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors all as specified and directed.

Ball brass valves high pressure with polythene float and fly nut complete, screwed for iron pipe or brass ferrule and fixed of dia 20mm all as specified and directed.

APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non wove fabric (wt. not less than 150 gms/sqm) land on primed surface by forced application and finished with solar reflective bitumenous aluminium paint/ primer @ 0.1Kg/sqm, incl 10 mm thick cement mortar 1:3 with WPC laid over all as specified and directed.

Supply only Liquid water proofing compound all as specified and directed.

20mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars window cills, cooking platforms and like in cement mortar 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigmet to match with shade of granite over and including 15mm thick screed in cement mortar 1:4 all as specified and directed.

Rounding to edges of stone slabs one edge, such as in steps, cooking platform, and other similar situations all as specified and directed.

Removal of excavated surplus soil not exceeding 50 m and depositing where directed at al level not exceeding 1.5 m above the starting point and all as specified and directed.

Use and waste of formwork for fair finished surface of chajjas, trough, fin and similar items including edges all as specified and directed.

Reinforced cement concrete M-25 design mix 1:2:4 type B1 using 20 mm graded stone aggregate for chajjas all as specified and directed.

Rendering 5 mm thick on fair faces of concrete surfaces in ceiling in cement mortar (1:3) and finished even and smooth without using extra cement completed all as specified and directed.

Preparation of newly plastered ceiling surfaces and applying three coats of white wash complete all as specified and directed.

Glazed Colour ceramic tiles (300x300mm) x 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match and including screed bed or bedding layer 15 mm thick in cement mortar (1:4). complete all as specified and directed.

Glazed Colour ceramic tiles (300x300mm) x 7mm thick, set and jointed in neat cement slurry and pointed in white or coloured cement to match for work on vertical surfaces such as skirting, dados and risers to steps etc. and including screed 10 mm thick in cement mortar (1:3). complete all as specified and directed.

Providing and fixing factory made uPVC white colour Sliding window Three track made of extruded profiles with wall thickness of 2.3mm (+ -0.2mm). Window profile with hollow section with multi chamber. Frame (88mm x 52mm), sliding sash (42mm x 67mm). Sliding mesh Sash (42mm x 57mm) Sliding interlock (One vertical length in each shutters) (45.5mm x 28mm), Glazing bead (24.5mm x 16mm) will be miterd cut and fusion welded at all corners, including drilling of holes for fixing hardware and drainage of water etc., making arrangement for fixing of hardware. EPDM gasket, 1.2+ -0.2mm thick galvanised steel Frame (30mm x 18mm) 2 nos, sliding sash (30mm x 18mm), sliding mesh sash (26mm x 10mm) profile to be inserted in required profile, frame will be fixed to the wall with 8mm x 100mm long fasteners, Hardware [Touch Lock of zinc alloyed (white powder coated), steel roller system. Stainless steel wire cloth 0.36mm nominal dia of wire and average width of aperture 1.40mm and required accessories. Area not exceeding 2.00 sqm each. Note: The unit rate quoted by contractor excludes cost of glass and includes frame all other connected accessories. Net Opening will be measured For payment purpose.

Material and labour for UPVC door with shutters .The construction profile shall be overall frame sectional size 60x58mm with wall thickness 2.70+/- 0.2mm extruded sections.The corners shall be plastic welded.The hinge side vertical outer frame shall be reiforced with galvanised steel profileof wall using 8mm dia 80mm long MS screws minimum 3 Nos on each side.The glazing shall be fixed to door frame with UPVC standared beadings of sectional size 24.05x16mm & 2mm thick.The bottom portion of door shutter shall be provided with UPVC board 5mm thick & 1Mtr in height and the balance shall be glazed excluding the shutter frame area.The shutter shall be fixed to frame using 3Nos of 3D hinges.The door shutter shall be provided with 6 mm thick toughened glass & 5mm UPVC board with EPDM rubber gasket, zinc plated mild steel multipoint locking arrangement with key incl zinc alloy (white powder coated) handles and two numbers zinc alloy (white powder coated) tower bolts complete all as specified and as directed.The cost of glass, sheet etc shall be deemed with the quoted rate. Make : Madhu Industries / Fenesta / Qute /Sarvesh Multi Plast India Ltd/ SMP Impex /H20 Solution or equivalent.

Excavation over areas not exceeding1.50m deep and getting out in soft/ loose soil all as specified and directed.

Sheet glass 4 mm thick ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane all as specified and directed.

Applying two coats of oil bound distemper over a coat of alkali resistant primer over a coat of 3mm thick wall care putty in two latyer 1.5mm each layer on newly plastered wall surface including preparation all as specified and directed.

Applying Two or more coats of 100% Premium acrylic emulsion paint having VOC less than 50 gm/litre and UV resistance as per IS 15489:2004, Alkali & fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over new surfaces all as specified and directed.

250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified and directed.

Floor door stopper of aluminium alloy body and tongue, anodised with hard drawn steel spring of 140mm overall all as specified and directed.

Anodised aluminium alloy Curtain rods including fixing with brackets, stops, rollers etc all as specified and directed.

Vitreous China wash down water closet pan (pedestal pattern), white (excluding flushing cistern), Plastic water closet seat cover and mild steel chromium plated or aluminised hinging device, trap and connction to drain and flush pipe complete all as specified and directed.

Rectangular Full CP ABS 85 mm Shower with Brass Arm (225 mm) all as specified and directed. Make Prayag or Equivalent

15 mm bore Brass CP wall mixer for mixing hot and cold water screwed down for iron pipe and fixed all as specified and directed.

100 mm outlet PVC (SWR) floor trap, plain with grating including jointing with solvent cement all as specified and directed.

Vitrified Ceramic Tile heavy duty 10mm thick (Square/ Rectangular) polished area of each tile not exceeding 0.36 sqm in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15mm thick screed bed or bedding layer of mortar in cement mortar 1:4 complete all as specified and as directed.

Light shade Virified Ceramic tiles 10 mm thick (square / rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed bed or bedding layer 15 mm thick in cement mortar 1:4 complete all as specified and directed.

Light shade Virified Ceramic tiles 10 mm thick (square / rectangular) polished, area of each tiles exceeding 0.36 sqm but not exceeding 0.42 sqm, as skirting, dados and risers to steps etc.set and jointed in neat cement slurry and pointed in white or coloured cement to match with tile laid over and including screed 10 mm thick in cement mortar 1:3 complete all as specified and directed.

Anti termite treatment to backfill in contact with foundation at the rate of 7.5 litres of emulsion per square metre of vertical surface (Area of the sub structure in contac with backfill to be measured) all as specified and directed.

Anti Termite treatment to the top surface of filled earth at the rate of 5 litres of emulsion per square meter of surface area complete all as specified and directed.

Anti Termite treatment to soil under plinth protection at the rate of 5 litres of emulsion per square meter of surface area complete all as specified and directed.

Anti Termite treatment to soil along with external perimeter of building at the rate of 2.25 litres of emulsion per square meter of perimeter wall complete all as specified and directed.

Pressed steel frames of size 105x60 mm for doors with one or more rebates including necessary fixing lugs, lock strike plate etc, complete all as specified and directed.

35mm thick factory made, second class hardwood panelled shutter (two panel) with lock rail and panel of 9mm BWP commercial ply or 12mm veneer particle board with commercial veneering on both faces. The size of the rail and as per IS 1003 (Part -I) Kiln seasoned and chemically pressure treated all as specified and directed.

Applying two coats of synthetic enamel paint over new wooden surfaces of any description not otherwise described over 10cm in width or girth over a coat of pink primer including preparation of surface complete all as specified and as directed.

Applying two coats of synthetic enamel paint on new steel surfaces over a coat of red oxide of any description not otherwise described over 10 cm width or girth icluding preparation of surfaces all as specified and as directed

Chimney bars (stright or camber) bearing bars, tongues or water bars for window frames, window guard bars, plain, let in and fixed independently in steel frames, L or T section supports for shelves etc., including welding and similar articles conforming to Fe-290 Gde E-165 complete all as specified and as directed.

Rendering 15mm thick cement mortar 1:4 on fair faces of brick work or concrete surfaces all as specified and as directed

Excavation over areas, not exceeding 1.5m deep and getting out in hard / dense soil complete all as specified and directed.

Sand filing under floors or in foundations including watering and consolidation complete all as specified and directed.

Machine pressed precast concrete interlocking paver block with grey cement and no pigment, of any shape and size conforming to IS 15658 -2006 of 80mm thick M-40 Grade all as specified and as directed.

Plain Cement Concrete (1:2:4) type B1 using 20mm graded stone aggregate as in coping sides of paver block complete all as specified and as directed.

Excavating in trenches, not exceeding 1.5 m wide and not exceeding 1.50M in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes etc. not exceeding 10 sq m on plan and not exceeding 1.5 m in depth and getting out in hard/ dense soil complete all as specified and directed.

Rendering 15mm thick cement mortar 1:4 on fair faces of brick work or concrete wall surfaces, finished surfaces fair and even without using extra cement complete all as specified and directed

PCC (1:3:6) type C-1 using 20mm graded stone aggregateas in coping,cills ,string courses,apex stone,bed plates,kerbs and the like including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified and directed

PCC (1:2:4) type B1 using 20 mm graded stone aggregate as in surface channel and drain including necessary form work, weathering, slightly rounded or chamfered angles and throating complete all as specified

Rendering 15mm thick in CM 1:3 on fair faces of cement concrete / brick walls mixed with water proofing compound finished the surface even and smooth without using extra cement complete all as specified and as directed. (Note: WPC shall be measured and paid separetly)

Cement concrete 1:4:8 type D2 using 40 mm graded stone aggrerate as in bed concrete to drainpipes 150 mm bore including packing under and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Reinforced Concrete pipes class NP-2 laid in trenches and in manhole and jointed complete with collars of 150mm dia all as specified and directed.

Precast cement concrete 1:2:4 type B1 using 20 mm graded stone aggregate as in landings, cover slab (for manholes etc) and similar work including necessary form work and set in cement mortar 1:4 complete all as specified and directed. Note :- Reinforcement shall be measured and paid separately.

Mild steel bars 10mm dia and above as in rungs, handles for manhole cover complete all as specified and as directed.

Removing excavated material exceeding 1.50 km but not exceeding 5km and depositing where directed at a level not exceeding 1.5 m above starting point complete all as specified and directed.

Precast RCC hume pipe septic tank with upflow designed to carry sewage and sullage water, excavation and returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25cm in any type of soil, PCC 1:4:8 below foundation, vent shaft, connection etc for 10 users complete all as specified and directed.

Soakage wells excavation, in any type of soil, foundation in PCC 1:3:6, walls of honey combed masonry with top ring of M25 concrete including intercepting chamber and screen chamber made of Brick masonary in CM, RCC cover slab in M25/ SFRC cover, interconnecting pipes of RCC/ DWC complete filled with brick bats of size 1.2 M dia X 1.5 M effective depth all as specified and directed.

Excavation in trenches not exceeding 1.5m wide and exceeding 1.5m and not exceeding 3m in depth for foundation not exceeding 10 sqm on plan and not exceeding 1.5 m depth getting out Hard /dense soil all as specified.

Excavation over areas, exceeding 1.5mtr but not exceeding 3.0mtr deep getting out in hard / dense soil all as specified and directed.

Steel reinforcement for concrete with Mild steel TMT bars grade Fe 550D 5mm dia and over cut and upto and including 10mm dia stirrups, spacers and binders, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with and incl mild steel wire (annealed) not less than 0.90mm dia or securing with clips all as specified and directed.

Rendering 15 mm thick in cement mortar 1:6 on fair faces of PCC block masonry/ concrete surface finished even and Smooth without using extra cement all as specified and directed.

Preparing newly plastered wall surface and applying two coats of cement base paint over a coat of alkali resistive primer all as specified.

Mild steel posts swan neck using angles conforming to Fe-290 Gde E-165 including cutting top to shape required, bottom with split ends embedded in concrete, drilling, welding etc. complete all as specified and directed. (Note: Concrete for embedding / fixing will be measured and paid separately.)

Galvanized two strand,steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacing and straining and fixing any type of standard rail straining bolts including securing or tying at crossing with and provision of galvanized MS steel wire with staples or steel pins all as specified and as directed.

Steel water tubing medium grade galvanized with all fittings and laid in trenches / fixed on walls / floors of size 15mm bore all as specified and directed.

Gun-metal gate valves with iron wheel head, screwed both ends for iron pipe and fixed of 15 mm dia complete all as specified and dirceted.

cutting exsiting pipe of any size and insert 15 mm bore GI pipe fitting i.e. Tee 15 mm bore including fittings all as apecified and directed .

Material and labour for Point wiring complete with 1.5 sqmm (nominal area) FRLS grade PVC insulated, unsheathed stranded copper conductor single core cable 1100 volts grade in and including PVC conduit medium grade in concealed complete with conduit fittings/ accessories including 1.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor and connected to common earth dolly for One light/Ex-fan point controlled by one switch 5Amps SP all as specified and directed. Note :1. Sunken box/ Cover plate for modular plate for modular switches, sockets etc will be measured and paid separately under relevant items and blank plate required if any will be deemed included in the item rate. 2. Cutting chases in stone masonry wall will be not included in the item rate.

All as per Item No.132 hereinbefore but One 3 pin 5A switch socket outlet on independent Board all as specified and directed.

All as per Item No 132 hereinbefore but point wiring complete with 2.5 sqmm for 3 pin 15 A socket outlet on independent board including 2.5 sqmm FRLS grade PVC insulated unsheathed stranded copper conductor cable for earth continuity conductor all as specified and directed.

Modular socket 2/3 pin combined 6A 230V AC 50 HZ SP two module all as specified and directed.

Modular socket 6A/16A 2/3 pin combined 230V AC 50 HZ SP two module all as specified and directed.

Modular switch one way 6A 230V AC 50 HZ SP one module all as specified and directed.

Modular switch one way 16A 230V AC 50 HZ SP one module all as specified and directed.

Modular Metal Flush Box 1/2 module rectangular block for mounting, switches, sockets, fan regulator etc. all as specified and directed.

Modular Metal Flush Box 3 module rectangular block for mounting, switches, sockets, fan regulator etc. all as specified and directed.

Modular Metal Flush Box 4 module rectangular block for mounting, switches, sockets, fan regulator etc. all as specified and directed.

Modular White Cover Plate with Frame 2 module all as specified and directed.

Modular White Cover Plate with Frame 3 module all as specified and directed.

Modular White Cover Plate with Frame 4 module all as specified and directed.

Ceiling rose, PVC polycarbonate isolated body with three terminals complete all as specified and directed.

MCB DB SPN 8 way 230 volts, double door type with minimum capacity of 200 Amps rated bus bar including necessary dummy plate and necessary civil works all as specified and directed. Make: ABB/ Legrand/ L&T.

240V, 10 KA 'C' curve miniature circuit breaker (MCB) of SPN and current carrying capacity 32 Amps, in the MCB DB Complete with connection testing and commissioning all as specified and directed. Make: ABB/ Legrand/ L&T.

All as per item No. 147. herein before but SP 6 to 32 Amps capacity all as specified and directed.

22W LED 125 Lum/Watts 4ft batten comprises of thermally conductive material pre-wired with high efficiency electronic driver, high translucent serrated milky white diffuser gets glare free, smooth light distribution lamp colour white all as specified and directed. Make. HavellsCat Part No. LHEXAWPN7IN1W025 / CG/ Philips / Bajaj.

Submain wiring with 2 runs of FRLS grade PVC copper conductor cable 6 sqmm, multistranded along with FRLS grade PVC insulated copper earth continuity conductor 6 Sqmm drawn through and including PVC Conduit pipe 20 mm dia with all fittings all as specified and directed.

Earthing complete with galvanised steel earth plate electrode 60x 60cm x 6mm thick, buried directly in ground (earth pit not lessthan 2.25 metres deep below ground level) with top edge of the plate notless'than 1.5 metres below normal ground level, connected togalvanised earth lead wire 4.0 mm dia by means of bolts, nuts, checknuts and washers of galvanised ironor steel all as shown in electricalplate No. 3 connected to earthing testpoint all as specified or indicated including testing on completion all as specified and directed.

Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit/ pipe or fixed to poles or any other indicated situation for loop earthing etc. as required 4mm dia galvanised iron or steel wire all as specified and directed.

MCB DB TPN 4 way 415 volts, double door type with minimum capacity of 200 Amps rated bus bar including necessary dummy plate and necessary civil works all as specified and directed. Make: ABB/ Legrand/ L&T.

415V 10KA 'B' curve Isolator four poles and 63 amps current carrying capacity in the DB complete with connection testing and commissioning.Make:Havells/ Legrand /C&S

Taking down old unsv 2ft FTL fitting Supply and fixing LED light fitting mirror type with high out put diffuser 2 feet, 10 watt 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed. Make - Havells Cat Part No-LHEXACP5IN1W010 / Philips/CG/Orpit

Exhaust fan made of sturdy Engineering plastic complete with louvers shutter, voltage 230V, 50 Hz, RPM 1200, Copper winding of sweep 250 mm including making openeing brick/stoan Masaonary Wall as per reqiurement of Exhuast Fan and make good and matching with existing surfaces complete all as specified and directed.

Electric Water heater storage type steel body with copper inner tank and heating element upto 2 KW capacity 25 litres.BEE 5 star rated complete with all accessories such as safety valve, thermostate, NRV, connection piece etc. all as specified and directed.

Single pole and neutral sheet metal enclosure with a two pin and earth plug and socket complete with one 20A SP MCB all as specified and directed.

LED Security Light fitting of 15 Watt comprising of eposy powder coated housing enclosed with glass cover in frame with protection IP 65 complete with all accessories and lamp colour white,110 Lumen/Watt all as specified and directed. Make: CG or equivalent in Philips / Bajaj.

GI Pipe Medium Grade 40 mm bore bracket of suitable size bent to shape of not less than 1.2m long with clamp made of GI flat Iron of size 32 x 6mm for street light fittings, duly painted with one coat of red oxide primer and two coats of aluminium based paint, fixed on poles with bolts, nuts and washers including taking down old brackets complete all as specified and directed.

Supply, laying, jointing and testing cable XLPE Insulated ,screened, PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 25.0 sq mm 3.5 core complete all as specified and directed.

Supply and spreading riddled sand in trenches as cushioning to under ground cable on top and bottom of cable all as specified and directed

Supply and Laying un-reinforced precast concretecable cover,Class LV, Type I ,flat size 250mm x 150mm x 40mm as protection to cable all as specified and directed

MCCB TPN 63 Amps, 240 Volts, rupturing capacity 16 KA. in existing LT Panel board for taking supply to proposed bldg.

S.RAMACHANDRAN (BID ID -3344016)

SREE CONSTRUCTIONS (BID ID -3340683)

sree devi construction (BID ID -3343726)

SIVAN BUILDERS (BID ID -3336320)