Provn of toilet block, chain link fencing and path at MIRC under GE (S) Ahmednagar

Amount

Demolition of cement concrete of any description and in any position not otherwise specifically provided all as specified and as directed.

Dismantling of posts or struts (wood, steel or RCC) embedded in concrete, brick work, masonry etc, any section including taking out embeded portion and making good disturbed ground complete all as specified and as directed.

Demolition of brick work/stone masonary built in cement mortar or cement lime mortar including all quoins, arches, pillars, etc complete all as specified and as directed.

Demolition of precast PCC solid block masonry built in cement mortar complete all as specified and as directed.

Dismantling old barbed wire / chain link fencing, any description complete all as specified and directed.

Demolition and breaking up drain pipes (salt glazed ware, 300mm internal dia, AC or reinforced cement concrete) set in cement mortar, all as specified and as directed.

Excavation over areas n exc 1.50m in depth and getting out in soft/loose soil all as specified and as directed.

Excavation in trenches, n exc 1.50m wide and n exc 1.50m in depth; for foundations, etc. or for manholes etc not exc 10 Sqm on plan and not exc 1.5m in depth and getting out in soft/loose soil all as specified and as directed.

All as per serial item No 8 but in hard/dense soil.

Earth work in excavation by mechanical means (Hydraulic excavator) in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil, within a lead of 50 m all as specified and as directed.

Returning, filling in, including spreading, leveling, watering and well ramming in layers not exc 25cm thick with soils all as specified and as directed.

Removing excavated soil to distance n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point all as specified and as directed.

M&L for moorum/red bajri filling in floors or pavings, laid in layers n exc. 15 cm thick, spread, levelled and rammed including watering all as specified and as directed.

M&L for hardcore of broken stone or boulders, guage exc 63mm but n exc. 100 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rolled/rammed to a true surface all as specified and as directed.

M&L for PCC 1:4:8, type D2, using 40mm graded stone aggregate as in foundations filling and mass concrete all as specified and as directed.

M&L for PCC 1:3:6, type C1 using 20 mm graded stone aggegates as in coping, cills, plinth courses, string courses, bed blocks including weathering, slightly rounded or chamfered angles and throating etc including necessary form work complete all as specified and as directed

M&L for PCC 1:3:6, type C1 using 20 mm graded stone aggegates as in surface channel, benching in manhole etc complete all as specified and as directed

Extra for forming fair finished drain or channel 30 cm inner girth in cement concrete, using ex- tra cement, including forms, moulds, mi- tred/stopped ends etc. all as specified and as directed.

M&L for pre cast manhole cover slab in RCC 1:2:4 type -B1 using 20 mm graded stone aggrgates including forms/ moulds and set in cement mortar 1:6 complete all as specified and as directed. Note : Reinforcement will be measured and paid separately.

M&L for RCC M-25, design mix, as in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, and mass concrete all as specified and as directed.

M&L for RCC M-25, design mix, as in columns, pillars, piers, posts and struts all as specified and as directed.

M&L for RCC M-25, design mix, as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like all as specified and as directed.

M&L for RCC M-25, design mix, as in beams, cantilevers, bressummers, lintels over 1.5m span all as specified and as directed.

M&L for RCC M-25, design mix, as in chajjas all as specified and as directed.

Supply only water proofing compound, ISI mark as aproved by GE all as specified and as directed.

M&L for precast cement concrete block masonry with solid block of PCC (1:5:8), exc 10 cm in width and built in cement mortar 1:6 complete all as specified and as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc. 6m mean radius, built in cement mortar 1:6 all as specified and as directed.

M&L for brick work with fly ash bricks, straight or curved on plan exc 6m mean radius built in cement mortar 1:6 complete all as specified and as directed.

M&L for walling of random rubble masonry uncoursed, well bonded, bedded and solidly hearted, built in cement mortar 1:6 complete all as specified and as directed.

Extra over stone walling for hammer dressing with maximum depression on face from straight edge held against the dressed surface n exc 20 mm to face stones and dressing of face beds and joints as specified of random rubble walling uncoursed or brought upto course complete all as specified and as directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter for rough finished flat surfaces of concrete all as specified and as directed.

Use and waste formwork to sides of pillars, posts, struts, piers, columns and stanchions for rough finished flat surfaces of concrete all as specified and as directed.

Use and waste formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200mm thick (Horizontal or sloping) for rough finished flat surfaces of concrete all as specified and as directed.

Use and waste formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including sup- ports, overhangs, etc. also splays between floors and beams, etc. for rough finished finished flat surfaces of concrete all as specified and as directed.

Use and waste formwork to chullah hoods, chajjas, troughs and similar items including edges for rough finished finished flat surfaces of concrete all as specified and as directed.

S&F 35 mm thick, second class hard wood, plain framed, factory made, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or 12 mm thick veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated all as specified and as directed.

S&F solid PVC door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with MS square tube, and fixed in opening all as specified and as directed.

S&F factory made solid PVC door shutter, 30mm thick (stiles), consisting of frame made out of MS tubes for top and bottom rail. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheet for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail, Panellng of plain colour PVC sheet to be fitted in the MS frame welded/sealed to the stiles and rails with suitable PVC sheet beading and joined toghter with solvent cement and fixed to frame complete all as specified and as directed.

S&F 100 mm size butt hinges, medium weight, cold rolled mild steel, and fixed all as specified and as directed.

S&F aluminium barrel tower bolt of extruded section 150mm long all as specified and as directed.

S&F aluminium handle anodised, fabricated type of size 150 mm all as specified and as directed.

S&F 250mm in long, aluminium anodised sliding door bolts with hasp, staple (bolt type) and fixing clips of sheet cast or extruded sections and fixing bolts and sliding bolts of extruded section, complete all as specified and as directed.

S&F mild steel pressed steel door frames of size 105mm x 60mm for doors with one or more rebates, including necessary fixing lugs, hinges, lock strike plate etc complete all as specified and as directed.

M&L for mild steel TMT bars, 10 mm dia and over, cut to length, bent to shape required, including cranking, bending, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips all as specified and as directed.

All as per serial item No 44 above but 6mm to 8mm dia.

All as per serial item No 44 above but 5mm dia and over, upto and including 10mm dia as in stirrups, spacers and binders

S&F mild steel windows, side hung, including projecting type hinges with steel handles and steel peg stay complete with glazing bars dovetailed or welded complete all as specified and as directed.

S&F mild steel ventilator with top hung shutter, including hinges, steel peg stay, complete all as specified and as directed.

S&F mild steel framed work conforing to Fe 290 Gde E-165 such as grills, gratings, guard bars etc with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars, barred iron doors ladders and smilar work all as specified and as directed.

M&L for machine made, mild steel bolts, 12 mm dia shank with hexagonal or square head one end and screwed the other or screwed both end, each screwed end to be fitted with, washers and one hexagonal or square nut, length not exceeding 15 cm long complete all as specified and as directed.

M&L for mild steel angle/flat iron as in supports for posts/strut for securing barbed/chain link fencing any description including drilling holes, notching for wire etc and similar work conforming to Fe-290 Gde E-165 complete all as specified and as directed.

S&F galvanized 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straining and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanized mild steel wire, staples or steel pins etc complete all as specified and as directed.

Supply only chain link fencing net, mild steel galvanised, made out of GI wire, complete all as specified and as directed. Note :- Dia and mesh size shall be as decided by GE.

Fixing only chain link fencing including line wires, any mesh, size and type to any type of standards,rails, straining bolts etc including provision of bindig wire complete all as specified and as directed.

S&F mild steel round bars as in line bars, cut to length, bent to shape required for fixing tof chain link fencing complete all as specified and as directed.

M&L for 75mm thick PCC 1:4:8, type D2, using 40mm graded stone aggregates as in sub base of flooring complete all as specified and as directed.

M&L for 75mm thick PCC 1:3:6, type C2 (using 40mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide & 10 mm deep and filling with bitumen mastic joint filling at every 3m length and at corners complete all as specified and as directed.

M&L for non-skid coloured ceramic tiles 7 to 8 mm thick (square/ rectangular), area of each tile exceeding 0.06 Sqm but not exceeding 0.11 sqm, as in floors etc. laid over and including 15mm thick screed bed in cement mortar 1:6, set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tiles complete all as specified and as directed.

M&L for glazed ceramic tiles, 7mm thick (plain or printed), area of each tile exceeding 0.11 Sqm but not exceeding 0.18 sqm, as in vertical surfaces like dado, skirting etc jointed in neat cement slurry and pointed in coloured cement, laid over and including 10 mm thck backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for machine pressed precast conctete interlocking paver block any shape and any size confirming to IS 15658-2006 of 60mm thickness, M -35 grade with grey cement and pigment, laid over and including 25mm thick compacted bed of fine sand, compacting and proper embedding/ laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; etc complete all as specified and as directed.

M&L for water proofing treatment to RCC roof slab, including parapet, comprising with the following treatment/specification from bottom to top:- (i) Screed bed or bedding layer of 10 mm thick cement mortar 1:4 with mixing of WPC @ 3% by weight of cement or as per manufacturers instructions and surface finished even and smooth without using extra cement. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.30 ltr /Sqm conforming to IS:3384-1986. (iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (iv) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm. Note: Water proofing compount will be measured & paid seperatly.

M&L for 10mm thick rendering in cement mortar 1:6 on other than fair faces of brick work or concrete surfaces finished even and smooth with sagol finish complete all as specified and as directed.

M&L for rendering 15 mm thick in cement mortar 1:4 on fair faces of brick work or concrete surfaces finished surfaces even and fair all as specified and as directed.

M&L for flush pointing to random rubble masonry, uncoursed or brought to course in cement mortar 1:4 complete all as specified and as directed.

M&L for preparation of new plastered surfaces of walls and applying three coats of white wash all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash all as specified and as directed

M&L for preparation of new plastered surfaces of walls applying two coats of cement base paint over a coat of primer all as specified and as directed

M&L for 3 mm thick sheet glass, ordinary quality and glazing with oil putty in square n exc 0.5 Sqm in each pane all as specified and as directed

M&L for preparation of new wooden surfaces of any description not otherwise described over 10cm width or girth and applying two coats of synthetic enamel paint over one coat of pink primer all as specified and as directed

M&L for preparing new steel surfaces of any description over 10cm width or girth not otherwise described and applying two coats of synthetic enamel paint over one coat of red oxide primer all as specified and as directed

S&F rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top), 1000 litres capacity, tripple layered, hoisted and fixed in position including 20 mm dia ball valve, high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed to iron pipe and connecting all as specified and as directed.

S&F 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and as directed

S&F vitreous china bowl urinal, flat back of size 465 x 355 x 265 mm white (minimum), with grating and union for discharge pipe (excluding flushing cistern, flush pipe and waste pipe) including urinal spreader of PTMT any colour for fixing with 15 mm dia pipe. (minimum weight 60 gms) all as specified and as directed.

S & F vitreous china wash hand basin, white flat back size 550 mm x 400 mm including brackets and pillar tap 15 mm bore chromium plated, fancy type, cast copper alloy with capstan heads, screwed down high pressure, with or without lettered 'Hot' or 'Cold' with long screwed shanks, 32 mm waste coupling brass chromium plated suitable for wash hand basins, with long screwed shanks and fly nuts and PVC waste pipe,15mm dia PVC connection pipe 600mm long, complete all as specified and as directed.

S&F vitreous china squatting pan, white, Orissa pattern of size 580 X 440 mm width with integral foot rest, set in cement concrete including 10 Litres capacity PVC valveless syphonic action type, flushing cistern, low level, white or coloured, with inlet, ball valve, float and handle including brackets etc, flush pipe and connecting to trap/flushing cistren complete all as specified and as directed.

S&F 15 mm bore GI tubing, medium grade with all fitting and fixed complete on walls (concealed or open)and ceilings or laid in floors etc complete all as specified and as directed.

S&F 20 mm bore GI tubing, medium grade with all fitting and fixed complete on walls (concealed oropen) and ceilings or laid in floors etc complete all as specified and as directed.

S&F GI tubing medium grade, 25 mm bore dia, laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all fittings such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc complete all as specified and as directed.

S&F GI tubing medium grade, 40 mm bore dia, laid in trenches / floors or fixed to wall in any length with screwed and socket joints together with all fittings such as sockets, bends, elbows, tees, reducers, unions, jointing materials etc complete all as specified and as directed.

S&F gun metal or bronze globe / ball valve, 25mm size, ISI marked, screwed both ends suitable for GI tubing with side way operating GI lever handle complete all as specified and as directed.

S&F gun metal or bronze globe / ball valve, 40mm size, ISI marked, screwed both ends suitable for GI tubing with side way operating GI lever handle complete all as specified and as directed.

S&F PVC connections, 15 mm bore, 450mm long with PTMT nuts complete all as specified and as directed.

S&F 15mm bore, stop cock, cast copper alloy, fancy type, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for union and fix complete all as specified and as directed.

S&F tubular towel rail, brass chromium plated, 20 mm dia `D' type, 60 cm long between flanges all as specified and as directed.

S&F bib taps, 15 mm dia, cast copper alloy chromium plated with crutch or butterfly handle, screwed down for iron pipe or for brass ferrule and fixed all as specified and as directed.

S&F PVC (SWR) floor trap of 75mm dia of outlet, plain with grating including jointing with solvent cement to waste pipe, including fixing in cement concrete type (1:2:4) type B1 complete all as specified and as directed.

S&F grating doom 100mm dia PTMT (minimum weight 25gms) all as specified and as directed.

S&F 40 mm bore low density polyethylene pipes (LDPE) of pressure rating 6 kgf/Sqcm and fixed to walls, ceilings or in floors etc.complete all as specified and as directed

S&F 75 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to walls or in any other position complete all as specified and as directed

S&F 110 mm dia PVC (SWR) pipes single socketed in any length with rubber ring joints and fixed to walls or in any other position complete all as specified and as directed

S&F of 75 mm dia PVC (SWR) bends with access door all as specified and as directed

S&F of 110 mm dia PVC (SWR) bends with access door all as specified and as directed

M&L for 200 mm internal dia, reinforced cement concrete pipes with collars, class NP2, laid and jointed complete all as specified and as directed.

M&L for 300 mm internal dia, reinforced cement concrete pipes with collars, class NP2, laid and jointed complete all as specified and as directed.

M&L for PCC 1:4:8, type D-2 using 40mm graded stone aggregates as in bed to drain pipes, 200mm bore, including packing under and haunching against the sides of pipes after they are laid and tested all as specified and as directed.

M & L for point wiring complete on surface of wall (open) type with two runs of 1.5 sqmm for phase and neuatral single core multistranded copper conductor cable of 1100 Volts grade PVC insulated and unsheathed , FRLS cable drawn through and including PVC casing and caping (ISI marked) and its accessories such as Tee, elbow, jointer, elbow corner etc. fixed on surface of walls, coloumns/ beams alongwith 1.5 Sqmm copper conductor cable (multistranded) PVC insulated and unsheathed FRLS cable as earth wire connected to common earth dolly at one end and metalic bodies of luminaire/ fan at other end including PVC folding boards for mounting switches, sockets, fan Regulators, accessories etc for One light/fan point controlled by one way switch all as specified and as directed NOTE: (1).Proper colour coding shall be adopted for wiring (for phas-RED,YELLOW,BLUE for Earth-Green and Neutral-Black) (2 ). All points shall be earthed up to fixtures i.e holders,tube lights,all lights,ceiling lights,bulkhead lights,bldg security lights etc.)

All as per serial item No 97 above but one 5 Amp 5 pin socket outlet point on same board with other switches

All as per serial item No 97 but for one switch socket out let 3 pin, 5 Amps point on independent board.

S&F switch piano, flush type , single pole , one way , 6 Amps, 230 volts complete all as specified and as directed.

S&F socket outlet flush type 5 pin 5 Amp multipurpose 230 volts single pole one way suitable for 3 pin/2pin 5 Amp plug top white/ivory finish all as specified and as directed.

S&F lamp holder angle/batten type, PVC/Polycarbonate type with back plate suitable for batten fittings all as specified and as directed.

S&F ceiling rose, surface PVC 50mm dia 3 terminals including PVC mounting block white/ivory finish all as specified and as directed.

S&F LED box type fitting pre-wired including LED tube 1 x 20 W connecting up with PVC insulated and sheathed 1100 volt grade flexible copper cable complete all as specified and as directed. Make:- Havells Model-LUMILINEPLUSBS20WLED865SPCSS or equivalent model of make Philips / GE/ Crompton/ Halonix/ Century LED/Luker

S&F sheet metal enclosure (Factory made) double door shutter type for distribution board (when MCBs are to be used) single pole and neutral, 240 volts, 8 way, protection class IP-42, suitabl for fixing MCBs, Isolators etc, confirming as per IEC 61439-3, suitable for flush mounting and surface mounting,with 100 Amps rated copper busbar, with Neutral bar,Earthbar and cable lies for cable managment,fully shrouded,Neutral bars,prefittes masking sheet complete all as specified and as directed. Make: Havells,Cat No:DHDMTHODDW08 or equivalent model of make Legrand/HPL/Indo Asian/Schneider/L&T

S&F MCB SP, AC 240 V, 6 to 32 Amps, 10 KA capacity, 'C' series, making connection with suitable size of copper lugs etc complete all as specified and as directed . Make: Havells Cat No DHMGBSPF006-32 or equivalent model of make Legrand/HPL/Indo Asian/Schneider/L&T

S&F MCB TPN, AC 240 V, 40 Amps, 10 KA capacity , 'c' series making connection with suitabl size of copper lugs etc complete all as specified and as directed. Make: Havells Cat No DHMGCTNF040 or equivalent model of make Legrand/HPL/Indo Asian/Schneider/L&T

S&F 300 mm sweep metallic exhaust fans, AC, single phase, 230/240 volt, with blades, frame and louvers including making hole in brick/stone masonry for fixing of exhaust fan and making good disturbed surfaces with cement mortar and cement plaster and applying two coats of distemper oil emulsion of same pattern/tint complete complete all as specified and as directed.

M & L for HDPE pipe (PE 100, SDR 21, 6Kgf/Sqcm PN06) 50 mm bore, for laying of LT cables etc complete with all accessories complete all as specified and as directed.

S&F XLPE insulated screened PVC bedded galvanised steel strip or wire armoured UG heavy duty electric cable with aluminium conductor 1100 volts grade cross sectional area of 10 sqmm 4 core size laid in trenches under floor/roads/hard standing along poles etc all as specified and as directed.

S&F security light of building with single piece new generation energy savng and environmental friendly long life LED, 30W, made up of pressure die cast aluminium housing with acrylic covers as diffuser with IP66 protection and impact resistance of IK07 including one bracket made of Light grade GI Pipe 25 mm dia 1.5 mtr long fixed to wall/ pole with two clamps made out of mils steel FI 40 mm x 5 mm and connect to nearest electric supply by three core 1.5 sqmm aluminium cable all as specified and as directed. Make : Havells Cat No ENDURACITYLITEPLATSL30WLED757SASYBOPC or equivalent model of make Philips / GE/ Crompton/ Halonix/ Century LED/Luker

M&L for earthing complete with galvanized steel earth plate electrode 60 cm X 60 cm X 6 mm thick, buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of plate not less than 1.5 mtr below ground level, connecting to the GI wire 4 mm dia , by means of nut bolts, check nuts and washer of the GI . Earth wire connected upto main earth point/DBs alongwith 15mm dia GI pipe, medium grade, including provision of concrete pit in PCC (1:2:4) type B-1 using 20 mm graded stone aggregates with 40 mm thick RCC (1:2:4) cover with reinforced with XPM (weight not less than 4 Kg / Sqm) and frame of angle iron 25mm X 25 mm X 3mm with lugs 2 Nos and with 6 mm dia MS bar handle made to shape, GI light grade 20 mm bore pipe for watering perforated at bottom 1.75 mtr long placed on top edge of earth plate, common salt and charcoal filling, test point made out of phosphorus bronze with fixing arrangement, funnel, wire mesh and earth work in hard/dense soil, returning filling in and removal of surplus soil to a distance not exceeding than 50 mtr, all as per electric plate No 3 of SSR Part I 2009 and connection to earth test point all as specified including testing on completion.

M/S. Z.K.ENTERPRISES, AHMEDNAGAR

PRAVIN NANDKUMAR WARULE

Vinod Enterprises

Poojan Infra and Developers

M/s. A P INFRA

M/s. Sagar Traders

M/s IBEX Engineers and Contractors