Construction of 02 No Block Type-III Residence (12No) in Ganga Sinchai Puram Staff Colony Telibag Lucknow.

Amount

Site Clearance & Layout etc.

Dry Earth Work In Foundation of masonary work for building works including lead up to 30m & lift up to 1.5m and it's disposal and back filling in all kind of soil up to 1.50m depth

Dry Earth Work In Foundation of masonary work for building works including lead up to 30m & lift up to 1.5m and it's disposal and back filling in all kind of soil from morethan 1.50m to 3.0m on depth

Providing and Laying in cement concrete 1:4:8 (1 cement :4 Coarse sand:8 graded stone aggregate 40mm nominal size) and curing complete including cost of form work in foundation and floors.

Class M-150 Brick work in 1:6 Cement & Coarse Sand ( of 2.25 F.M. ) mortar in foundation & Plinth including supply of all material, Labour, tools and plants etc. required for proper completion of work.

Earth work in filling by power transport for a lead up to 1.00 km. including excavation, loading, unloading, royality, manual compaction & dressing including all lift.

Local Sand filling in plinth under floors including watering, raming, consolidating and dressing complete including lead up to 50m and lift up to 1.5m and including cost of sand.

Providing and injecting chemical emulsion for preconstructional antitermite treatment and creating a chemical barrior under and alround the column pits wall trenches basement excavation top surface if plinth filling junction of wall and floor , along the external perimeter of binding expansion joints, surrounding of pipes and conduits etc., complete (Plinth area of the building at ground floor only shall be measured as per I.S. 6313(Part II 1981) alderine emulsifiable concentrate or any other approved material such as Heptrachlor or Chlordane will be used. The rate of application of chemical emulsion shall be as follows:(1) Treatment for masonary & Foundation 5 liters per Sqm.(2) Back fill in immediate contact with foundation 7.5 liter/sqm. (3) Treatment of top surface of plinth filling 5 liter/sqm.(4) Treatment junction of wall and the floor 7.5 liter/sqm. (5) Treatment of soil along external perimeter of building 7.5 liter/sqm.(6) Treatment of soil under apron along external perimeter 5 liter/sqm. (As per manufacturer's standard dilution )

R.C.C. work with cement approved coarse sand and 20 mm gauge approved stone gritt in the proportion of 1:1.5:3 inPlinth Band , lintels of doors and windows, Sunshade/ Chhajja , Beam and Slab excluding supply of reinforcement and it's fixing & binding the same with 24 BWG binding wire and Excluding necessary centering and shuttering etc. and including supply of all materials, labour and tools and plants etc. required for proper completion of works. Strength of concrete shall not be less than M-200

Providing & applying a coat of residual petroleum bitumen of grade of VG-10 of approved quality using 1.7kg per square metre on Plinth Band after cleaning the surface with brushes and finally with apiece of cloth lightly soaked in kerosene oil.

Class M-150 Brick Work with 1:6 Cement & C.Sand mortar in super structure above plinth level including necessary cutting and mouldling of Brick Work as required etc. all Compl. Of work.

Class M-150 Brick Work in 1:3 Cement and Coarse sand mortar in super structure for wall thickness 12Cm. & Below brick work.

S/F Pressed Steel Chaukhat made of M.S. steel 18 gauge including iron but hinges of 10x3mm ISI marked, drilling holes of L-drop tower bolt and 230x40x6mm flat iron hole fast including supply of all material, Labouyr and T&P carriage up to site with (A) Section 120x50mm for double the rebate door chaukhat with 6 hinges.

S/F Pressed Steel Chaukhat made of M.S. steel 18 gauge including iron but hinges of 10x3mm ISI marked, drilling holes of L-drop tower bolt and 230x40x6mm flat iron hole fast including supply of all material, Labouyr and T&P carriage up to site with (B) Section 100x50 mm for single the rebate door chaukhat with 3 hinges.

Fabrication of mild steel/iron work in grill, gates railing, door and window frames including cutting, drilling, welding/ riveting and hinges, where necessary and fixing in position including cost of all material, labour T&P etc. required for proper completion of work with one coat of red oxide primer. (A) Providing & Fixing of door / windows grill.

Fabrication of mild steel/iron work in grill, gates railing, door and window frames including cutting, drilling, welding/ riveting and hinges, where necessary and fixing in position including cost of all material, labour T&P etc. required for proper completion of work with one coat of red oxide primer. (B ) Stair Case Hand Rail

Fabrication of mild steel/iron work in grill, gates railing, door and window frames including cutting, drilling, welding/ riveting and hinges, where necessary and fixing in position including cost of all material, labour T&P etc. required for proper completion of work with one coat of red oxide primer. (C ) Providing & Fixing of Z-Section steel windows

Fabrication of mild steel/iron work in grill, gates railing, door and window frames including cutting, drilling, welding/ riveting and hinges, where necessary and fixing in position including cost of all material, labour T&P etc. required for proper completion of work with one coat of red oxide primer. (D) Providing and fixing in position collapsible steel shutters with vertical channels 20x10x2 mm and braced with flat iron diagonals 20x5 mm size, with top and bottom rail of T-iron 40x40x6 mm, with 40 mm dia steel pulleys, complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of approved steel primer.

Providing and fixing wire gauge laminated veneer lumber shutters conforming to IS : 14616, and as per TADS 15 :2001 (Part B) using galvanised wire gauge with average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm as per IS :1568, for doors, windows and clerestory windows fixing with butt hinges of required size with necessary screws, as per directions of Engineer-in-charge.

Providing & Fixing ISI marked flush door shutters confirming IS: 2202 non decorative type , core of block board construction with frame of Ist class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters . 30mm thick including ISI marked stainless steel butt hinges with necessary screws.

Providing and fixing 25 mm thick flush door shutters (For Cup Board)including ISI marked Stainless Steel but hinges with necessary screws ISI markedconforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Mild Steel or Iron in plain work such as reinforced Concrete or Reinforced Brick work (When not included in an over all rates) wrought to required shape as necessary including bending for proper compl. Of the work and including supply of all steel and wastages and overlapping and hooks.

12mm Cement Plaster with 1:4 (1 Cement: 4 Coarse sand) in single coat on rough side of single or half brick wall for interior/ exterior plastering under plinth level & Super structure

12mm thick Cement Plaster with 1:6 (1 Cement: 6 Coarse sand) in single coat on rough side of single or half brick wall for interior plastering etc. all compl. Of work.

Making grooves 10 to 12mm wide x 8mm deep in plaster of the walls or in ceiling vertically or horizontaly as required.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick bed of cement mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sq.m including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Kota stone flooring over 20 mm (average) thick baselaid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) :25mm Thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 Cement : 4 coarse sand), joints treated with white cement, mixed with matching Pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Cement concrete 1:2:4 (1 Cement :2 Coarse sand : 4 graded stone aggregate 20mm nominal size for precast unitas bed block gap, pressed steel chaukhat filling and for hold fast M-15 concrete etc. complete.

P/F 4mm thick float glass panes with putty/nails of modi/ equivalent ISI marked quality putty , brands and springs complete.

P/F of wire mesh at Z-Section Window with 12x5mm flat Iron including all Labour , material and T&P etc. all compl. Of work.

Plain cement concrete floor with (1:2:4) cement, approved C. sand and 2 Cm. graded approved stone laid in pannels finished with 3mm flooring coat of neat cement or cement and marble dust in 5:1 as specified over and giving them a uniform finish including supply of all material labour & T&p etc. required for proper compl. of the work. (A) 4o mm thick Ground floor

Plain cement concrete floor with (1:2:4) cement, approved C. sand and 2 Cm. graded approved stone laid in pannels finished with 3mm flooring coat of neat cement or cement and marble dust in 5:1 as specified over and giving them a uniform finish including supply of all material labour & T&p etc. required for proper compl. of the work (B) 25 mm thick for first floor & Second Floor

25mm thick cement plaster in dado/skirting in 1:2 (1 Cement :2 Coarse sand) laid in panels, finished with 3mm floating coat of neat cement and marble dust in ratio of 5:1 including supply of all materials labour T&P etc. required for proper compl. Of the work.

Supply & Fixing of Glass stripps for flooring (A) 40mm wide & 3.15mm thick

Supply & Fixing of Glass stripps for flooring (B) 25mm wide & 3.15mm thick

Painting or varnishing on iron work in small areas or new wood work with one coat of ready mix priming paint and two coat of approved superior quality ready mix paint of clear synthetic varnish including supply of all materials labour /T&P etc required for proper completion of work.

Providing and applying white cement based putty of average thickness 2mm, of approved brand and manufacturer, over the plastered wall surfaceto prepare the surface even and smooth complete.

White washing with lime on undecorated ceiling (Two coat ) to give an even shade including throughly brooming the surface to remove all dirt,dust mortar drops and other foreign matter.

Distempering (Two coat) with oil bound distemper of approved brand and manufacturer of required shade on undecorated wall surface to give an even shade over & including a priming coat with cement primer of approved brand & manufacturer such as Berger, J&N ,Shalimar,Asian paint after throughly brushing the surface free from mortar droping & other foreign matters and also including preparing the surface even with plaster of paris or approved synthetic material & sand papered smooth including cost of all materials.

Finishing walls with Acrylic smooth exterior paint of required shade on new work with two or more coat applied @ 1.67 Lt./10 Sqm. Over and including Priming coat of exterior primer applied @ 2.20 kg./ 10 Sqm. (ace. Adv. Wall masta Asian , Berger)

Providing & Fixing ISI marked stainless steel sliding door bolts with nuts and screws etc. complete. 250mmx10mm

Providing & Fixing ISI marked Stainless steel tower bolt black finish, with nuts and necessary screws etc. Complete. 250mmx10mm

Providing & Fixing ISI marked Stainless steel handels confirming to IS:4992 with necessary screws etc. Complete.

Providing & Laying of light cinder filling under floor of Toilets & other sunken roofs.

Providing & Laying waterproofing treatment in sunken portion of W.C. /bathroom etc. by applying cement slurry mixed with water proofing cement compound consisting of applying:-(A) First layer of slurry of cement @0.488Kg./Sqm. Mixed with water proofing cement compound @ 0.253Kg./Sqm. This layer will be allowed to air cure for 4 hours. (B) Second layer of slurry of cement @0.242Kg./Sqm. mixed with water proofing cement compound @0.126Kg./Sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. The rate includes preparation of surface, treatment and sealing of all joints, corners, junction of pipes and masonary with polymer mixed slurry. (C ) 12mm Cement plaster in single coat in 1:6 (1 Cement : 6 Coarse sand ) and integral water proofing compound

Providing and laying water proofing on roof after surface preparation applying DONCRETE A&B / Roof coat-AR / Supercrete-SB(IS:13435,part-), or equivalent (Epoxy Grout) polymer based coating (two pack system) @ 400 gm./Sqm. Second Layer @ 600 gm./Sqm. By brush and protective layer of 20mm thick cement: Coarse sand (1:4) admixed with Concrete Bond-101/ Warrior-W-4 or equivalent polymer (SBR Polymer) based bonding materials one kg. per bag of cement finishing the surface with neat cement and making of (300x300)mm square. the entire treatment will be taken up to 30cm. on parapet wall.

Providing precast cement concrete Jaali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits.

Centering and shuttering for RCC. Work including rent of shuttering, material, labour and T&P required for proper completion of work for lintels sumshades and columns etc.

P/F nickle plated M.S. pipe curtain rods with nikle plated brackets.(A) 20mm dia

Providing & Fixing CPVC Pipe for spout

Providing and fixing water closet squatting pan (Indian type W.C. pan ) with 100 mm sand cast Iron P or S trap, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever) conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required:White Vitreous china Orissa pattern W.C. pan of size 580x440 mm with integral type foot rests.

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : W.C. pan with ISI marked black solid plastic seat and lid

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require:White Vitreous China Flat back wash basin size 550x 400 mm with single 15 mm C.P. brass pillar tap.

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (A) 32mm dia

Providing and fixing P.V.C. waste pipe for sink or wash basin including P.V.C. waste fittings complete. (B) 40mm dia

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required . Kitchen sink with drain bord size 610x510mm and bowl depth 200 mm

P/F C.P. brass jet spray for E.W.C. as per requirement .

Providing & Fixing 60x2 cm. C.P. brass towel rail complete with C.P. brass brackets fixed to wooden cleats with C.P. brass screw.

P/F soap tray parryware

Providing and fixing on wall face unplasticised Rigid PVC soil & water waste pipe conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised Rigid PVC soil & water waste pipe conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 75 mm diameter

Providing & Fixing PVC Nahani-trap with grating including jinting with solvent cement, cost of cutting and making good the wall and floors. 100mm Inlet & 75mm outlet.

Providing & Fixing Slotted Cowl (terminal guard.) 110mm

Providing & Fixing Slotted Cowl (terminal guard.) 75mm

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Coupler 75mm dia

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Coupler 110mm dia

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Single "T" with door 75x75x75mm

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Single "T" with door 110x110x110mm

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Bend End 87.5° 75mm Bend

Providing & Fixing on wall face unplasticised PVC moulded fittings and accessories confirming to IS:13592 Type-B including jointing with seal ring confirming to IS:5342 leaving gap of 10mm for thermal expansion. Bend End 87.5° 110mm Bend

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 75mm dia

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110mm dia

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. Internal work - Exposed on wall(i) 40mm dia nominal outer dia pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15mm dia nominal outer dia pipes

Providing and fixing 45cm uplasticised PVC connection pipe with brass unions.15mm nominal bore

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931(I) 15mm nominal bore

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 15mm nominal bore

Providing and fixing ball valve (brass) of approved quality, High or low pressure, with plastic floats complete :25mm nominal bore

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :40mm nominal bore

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Providing & Fixing brass Stop cock of approved quality.15mm nominal bore

Excavating trenches of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, depth upto 1.5 m, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m :Pipes 80mm to 300mm dia

Providing and fixing on wall face unplasticised Rigid PVC soil & water waste pipe conforming to IS : 13592 Type B, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes.160mm diameter

Providing and fixing square-mouth S.W. gully trap class SP-1 completewith C.I. grating brick masonry chamber with water tight C.I. coverwith frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design: 150x100 mm size P type

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) :

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 40mm nominal bore

Constructing masonry Chamber 60x60x75 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size ) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm 1461 SUB HEAD : 18- WATER SUPPLY nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 150

Providing & Laying of Cement conc. In base excluding the cost of centering & shuttering by 1:3:6 (1 Cement: 3 C.Sand : 6 graded stone aggregate 40mm nominal size)

Class M-150 Brick work in 1:4 Cement & Coarse Sand ( of 2.25 F.M. ) mortar in foundation & Plinth including supply of all material, Labour, tools and plants etc. required for proper completion of work.

12mm Cement Plaster with 1:2 (1 Cement: 2 Coarse sand) in side septic tank with mix of water proofing compound.

Providing M.S. Foot rest including fixing with 20x20x10 cm. Cement conc. Block 1:3:6 (1 Cement:3 C.sand: 6 graded aggregate) of nominal size 20mm as per standered design with 20x20 mm square bar.

Providing & Fixing PVC tee at the Inlet & Out let of septic tank

Providing & Fixing of 75mm dia Vent pipe

Providing and fixing in position pre-cast R.C.C. manhole cover and frame of required shape and approved quality M.D.-10 circular shape 500mm interna; diameter.

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. 19.32.1 With common burnt clay F.P.S. (non modular) bricks of class designation 7.5 D

Wiring point for light with 1 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid pvc conduit pipe on surface, complete with 14 SWG copper earth continuity wire,piano type switch and ceiling rose/angle/ batten holder on 3 mm. thick phenolic laminated backelite sheet etc.

Wiring points for two ways light with 1 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid pvc conduit pipe on surface, complete with 14 SWG copper earth continuity wire, two ways 2 nos. piano type switches & ceiling rose/ angle/ batten holder on 3mm. thick phenolic laminated backelite sheet etc., complete in all respect, as directed.

Wiring point for fan /fresh air fan (light duty exhaust fan) with 1.5 sq.mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid pvc conduit pipe on surface complete with 14 SWG copper earth continuity wire, piano type switch & ceiling rose on 3 mm. thick phenolic laminated backelite

Wiring Point for plug with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid pvc conduit pipe on surface,complete with 14 SWG copper earth continuity wire and piano type switch and socket etc.

Wiring point for call bell with 1.5 sq. mm.FRLSH PVC insulated multistrand single core copper conductor cable in heavy guage rigid pvc conduit pipe concealed in the wall, complete with 14 SWG copper earth continuity wire and piano type bell push or 2 pin socket etc., complete in all respect including matching colour wash

Supply and wiring of submain with two number 4 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 20 mm dia heavy duty (2 mm thick) PVC conduit with one no. 2.5 sq. mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit. including matching colour wash etc. complete in all respect.

Supply and wiring of submain 4 number 6 sq.mm. FRLSH PVC insulated 1100 V grade multistrand single core copper conductor cable in 32 mm dia heavy duty (2 mm thick) FRLSH PVC conduit with 2 nos 4 sq.mm. FRLSH PVC insulated multistrand copper conductor cable as earth continuity wire drawn in conduit.etc, complete in all respect.

Erection and testing of ceiling fan and regulator for room height upto 3.5 metres including supply of 3mm thick G.I.Pipe19mm dia. Duly painted, complete in all respect.

Erection and testing of exhaust fan on the existing hole with suitable size of rag bolts, nuts and washers etc., complete in all respect.

Supply and fixing hexagonal fan box with hexagonal side of approx 80mm in length fabricated from 16 SWG MS sheet incorporating 10mm dia. M.S. round bar duly bent for supporting fan hanger duly painted with red oxide and screwing arrangement with wiring conduit laid in the R.C.C. roof before concreting alongwith supply of all material, labour, T&P etc. required for proper completion of the work.

Supply and fixing of single light wall bracket on matching M.D.F.E.G. Board base etc. complete in all respect.

Supply and fixing of LED tube lightwith batten suitable for up to 1 x 22 watt LED tube light fitting including tubeon surface complete in all respect.

Supply and fixing of call bell of approved make on polished MDFEG / Teak ply board including making connections etc. complete in all respect.

Construction of recess of 600mm x 480mm x 200mm size of main boards, distribution boards of all sizes including cutting of brick work, providing lintel of suitable size and thickness, plastering etc. with supply of all materials labour T&P required for proper completion of work.

Supply and fixing of factory fabricated M.S. box in existing sunk of size 600mm x 480mm x 200mm deep with Godrej type almirah, cover with handle etc. fabricated from 18 SWG (1.25mm) M.S. sheet duly painted with red oxide primer followed by two coats of synthetic enamel paint complete with necessary conduit entry and D.P./T.P.N.; fixing arrangements and provision for compartment for loose wires openable housing on the top and hold fast etc. including supply of all material, labour, T&P etc. required for proper completion of the work.

S & F surface/Flush mounting 4ways V TPN distribution board without additional Door without MCB complete in all respect, as directed at site by Engineer in charge.

Supply & Fixing of 240Volts 'L' series miniature circuit breaker 9K.A./10 K.A. in existing MCB, DB complete with connection as required.6-32 amps.

Supply ,Fixing and making connection of following FPMCBS complete in all respect as per direction and satisfaction of Engg.-In-Charge. 6amp. To 32 amp. TPN MCB (10KA)

Supply and fixing of power plug with 15A/250 volt flush type switch and 5 pin 15A/250V flush type universal socket in suitable M.S. box of 175mm x 100mm x 50mm size with phenolic laminated bakelite sheet cover 3mm thick fixed with brass machine screw and cup washer.

Supply and Fixing Single Pole MCBS blanking plate complete in all respect.

MAIN DB-1 8 Way V TPN-DB (As per PWDSOR 2018 & Item No. 1030(I) Cat. B Incoming :100 amp. 4 pole Isolator 1 No. (As per PWDSOR 2018 & Item No. 1007(C) Cat. B) Outgoing: 40amp TPN MCB 6 No.(As per PWDSOR 2018 & Item No. 1020 Cat. B) 6 Amp. To 32 Amp. SPN/DB MCB 1 No.(As per PWDSOR 2018 & Item No. 1013 Cat. B)

Supply and burying of 600mmx600mmx6mm G.I. plate, vertically for earthing with its top atleast 3mts. Below ground level complete with 20mm G.I. pipe and funnel for watering and two earthing leads of 8 to 10 SWG G.I. wire in 15mm dia G.I. pipe up to switch board (From apron to switch board the cost of G.I. pipe and G.I. wire will be extra ) 30cm. square C.I. frame with hinged cover, masonary housing, alternate layers of chorcoal/coke and salt at least 150mm thick alround etc. complete in all respects.

Supply & Fixing of two numbers 8 SWG G.I. wire for earthing purpose as required complete in all respects.

Supply and Laying of aluminium conductor PVC insulated armound served sheathed cable 1100 V graded at depth of 750mm below ground level over a cusion of 75mm thick sand all arround & protected with burnt bricks on sides and on top. On surface the cable shall run be fixed on M.S. clamps etc. of suitable size or as directed by the Engg.-In-Charge complete in all respect. The armouring of the cable shall be properly connected with earth conductor by clamps etc. 25Sqmm. 3.5 Core cable

Supply & Fixing of plain or pin type copper tin plated cable socket (Lugs) to the cable leads insulating with tape and making connection etc. compl. In all respect as per direction of the Engg.-In-Charge.

Providing and Laying Unplasticized rigid PVC pipe confirming to IS:13592 type A including jointing, cutting and making good the walls & floors as per requirement. 32mm

M/S V.K CONSTRUCTIONS