Repair/renovation of lab No. 117 (at Ist floor) of Soil Science department in the premises of College of Agriculture at CCS HAU, Hisar (including PH and EI works)

Amount

Civil work 1 to 35:- Demolishing brick work manually/ by mechanical means including stacking of serviceable material and disposal of unserviceable material within 50 metres lead as per direction of Engineer-in-charge. (HSR 5.7.4) In cement mortar

Demolishing cement concrete manually/ by mechanical means including disposal of material within 50 metres lead as per direction of Engineer - in - charge. (HSR 5.23.1) Nominal concrete 1: 1.5:3 or richer mix (i/c equivalent design mix)

Extra for cutting reinforcement bars manually/ by mechanical means in R.C.C. or R.B. work (Payment shall be made on the cross sectional area of R.C.C. or R.B. work) as per direction of Engineer-in-charge. (HSR 5.27)

Disposal of building rubbish / malba / similar unserviceable, dismantled or waste materials by mechanical means, including loading, transporting, unloading to approved municipal dumping ground or as approved by Engineer-in-charge, beyond 50 m initial lead, for all leads including all lifts involved. (HSR 5.70)

Reinforced cement concrete work in beams, suspended floors,roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor four level, excluding the cost of centering, shuttering, finishing and reinforcement with 1: 1.5:3 (1 cement : 1.5 coarse sand(zone-111) : 3 graded stone aggregate 20 mm nominal size). (HSR 6.16)

Centering and shuttering including strutting, propping etc. and removal of form for (HSR 6.30.4) Shelves (Cast in situ)

Steel reinforcement for R.C.C. work, where not included in the complete rate of RCC, including straightening, cutting, bending, placing in position, binding, wastage, overlaps, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire etc. complete in all respect below plinth level Note:- Reinforcement shall be measured in length including hooks, if any, separately for different diaMeters as actually used in work , excluding overlaps. Wastage, overlaps, couplings, welded joints, spacer bars, chairs, stays, hangers and annealed steel wire or other methods of binding & placing shall not be measured and cost of these items shall be deemed to be included in the rates for reinforcement. (HSR 6.33.6) Thermo-Mechanically Treated bars of grade Fe-500D kg or more.

Half brick masonry with common burnt clay non-modular bricks of class designation 7.5 in superstructure above plinth level up to floor IV level. (HSR 7.28.2) Cement mortar 1 :4 ( 1 cement :4 coarse sand)

Providing and fixing tiled false ceiling of specified materials of size 595x595mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm centre to centre and cross 'T' of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm centre to centre to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main 'T' runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1 .6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm centre to centre along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge. (HSR 9.47.5) 12.5 mm thick tapered edge gypsum fire resistant board conforming to IS: 2095- Part I

Providing and fixing mineral fibre false ceiling tiles at all heights of size 595X595mm of approved texture, design and pattern. The tiles should have Humidity Resistance (RH) of 99%, Light Reflectance i!: 85%, Thermal Conductivity k = 0.052 - 0.057 w/mK, Fire Performance as per (BS 476 pt - 6 &7)in true horizontal level suspended on interlocking T-Grid of hot dipped all round galvanized iron section of 0.33 mm thick (galvanized @120 gsm) comprising of main T runners of 15x32 mm of length 3000mm, cross T of size 15x32mm of length 1200 mm and secondary intermediate cross T of size 15x32 mm of length 600 mm to form grid module of size 600x600 mm suspended from ceiling using galvanized mild steel item (galvanised@80gsm) 50 mm long 8mm outer diameter M-6 dash fasteners, 6 mm diameter fully threaded hanger rod up to 1000 mm length and L-shape level adjuster of size 85x25x2 mm, spaced at 1200 mm centre to centre along main 'T'. The system should rest on periphery walls /partitions with the help of GI perimeter wall angle of size24x24X3000 mm made of 0.40 mm thick sheet, to be fixed to the wall with help of plastic rawl plug at 450 mm centre to centre & 40 mm long dry wall S.S. screws. The exposed bottom portion of all T-sections used in false ceiling support system shall be pre-painted with polyester baked paint, for all heights. The work shall be carried out as per specifications, drawings and as per directions of the engineer-in-charge. (HSR 32.47.3) With 16 mm thick bevelled tegular mineral fibre Antimicrobial false ceiling tile confirming to ISO 5 (class 100 ) specifications

Providing and fixing 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1 :3 (1 cement : 3 coarse sand) and jointing with grey cement slurry@ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete. (HSR 10.62)

Providing and fixing ceramic & Glazed tiles/ vitrified tiles/ of any size of approved make in floors / dados, laid in any pattern as specified over base of 3 mm thick adhesive of reputed brands as per IS specification 15477-2004 using 5 Kg. adhesive per sqm area of tiles and jointed with white cement slurry mixed with pigment to match the shade of tiles excluding cost of tiles. (HSR 10.73)

12 mm cement plaster of mix : 1 :6 (1 cement: 6 fine sand) (HSR 11.5.4)

15 mm cement plaster on the rough side of single or half brick wall of mix : (HSR 11.6.2) 1 :6 (1 cement: 6 fine sand)

Providing and applying two coats white cement based putty of approved brand and manufacturer, over plastered surface and grinding the surface smooth with sand paper to get en even and smooth finish including cost and carriage of all material , labour charges, scaffolding, sundries etc. complete (HSR 11.58)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade: (HSR 11.64.1) New work (two or more coats) over and including water thinnable priming coat with cement primer

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface: (HSR 11.67.1) Water thinnable cement primer

Providing and fixing aluminium handles, ISi marked, anodised (anodic coating not less than grade AC 1 O as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete (HSR 12.102.3) 75 mm

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / panelling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, panelling and dash fasteners to be paid for separately) : (HSR 12.157.1.1) For fixed portion Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) (HSR 12.157.2.1) Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Providing and fixing 12 mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade I Type II, in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. (HSR 12.158.2 ) Pre-laminated particle board with decorative lamination on both sides

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): (HSR 12.159.2 ) With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing double action hydraulic floor spring of approved brand and manufacture conforming to IS : 6315, having brand logo embossed on the body / plate with double spring mechanism and door weight up to 125 kg, for doors, including cost of cutting floors, embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece M.S. sheet outer box with slide plate etc. complete as per the direction of Engineer-in-charge. (HSR 12.160.2) With brass cover plate minimum 1.25 mm thickness

Providing and fixing aluminium round shape handle of outer dia 100 mm with SS screws etc. complete as per direction of Engineer-in-charge (HSR 12.167.1) Anodized (AC 15 ) aluminium

Removing white or colour wash by scrapping and sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete (HSR 30.21)

Painting with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade One or more coats on old work (HSR 30.28.1)

Providing edge moulding to 17-20 mm thick granite stone single counters, vanities etc. including machine polished to edge to give high finish etc. complete as per design apprvoed by Engineer-In-Charge (Moulding) (NS)

Removing of existing cabinet shutter with chowkat by making recess in wall including remonving its fitting for re-use and shifting the same to store, complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing 15 mm to 18 mm thick Z-Black granite stone (polished) on worktop laid in any pattern as specified over base of 12 mm thick cement coarse sand mortar 1:3 and jointed with white cement slurry mixed with pigment to match the shade including rubbing and polishing, complete. (NS)

providing and fixing 6mm thick HPL Sheet Strips of 4’’ width (Make:- Green, Century, Alstone or Sunderk of approved colour) for worktop face including adhesive etc., complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing 4’’ long aluminium T-bolt with necessary screws etc. for aluminum shutter under worktop, complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing 3’’ long hasps and staples of aluminium with necessary screws etc. for aluminium shutter under worktop, complete in all respect as directed by Engineer-in-charge. (NS)

Providing and fixing wall cabinet of size 16’-0’’ long 3'-0" high and 1'-0" deep consisting of following:- (i) 19mm thick BWR Grade-II block board (ISI mark) of approved make having three horizontal pieces (one at top, one at Centre and one at bottom) vertical pieces @ 2'-0" c/c for making compartments (each for size 2'-0" x 3'-0"). Outer face of the cabinet except back finished with1mm thick plastic laminated sheet (ISI mark) of approved make, shade & colour and inner side of cabinet finished with primer & painting. (ii) 6mm thick plywood BWR Grade-II (ISI mark) of approved make on back of cabinet. (iii) 30 mm thick openable shutters in all compartments (each of size 2'-0"x 3'-0") consisting of 4mm thick glass in wooden style frame of commercial hard wood such as hollock, champ, chikrasy & chaplash. (iv) Wooden beading of commercial hard wood such as hollock, champ, chikrasy & chaplash etc. of size 0'- 3/4" & 0'-1/2" on all edges. (v) Angle iron 1'-6" long (at bottom of rack/cabinet) of size 25mmx25mmx5mm @ 4'-0" c/c embedded in cement concrete 1:2:4 blocks after making khudas in wall and MS flat at top of cabinet @ 4'-0" c/c of size 25mmx6mm. (NS)

Providing readymade white writing board of PRESKO make with delux frame or any other similar brand, fixed in position, including wooden gutties, nails and screws, etc., complete in all respects as per drawing and design. (NS)

Public health work 36 to 53:- Providing and laying cement concrete in retaining walls, return walls, walls (any thickness) including attached pilasters, columns, piers, abutments, pillars, posts, struts, buttresses, string or lacing courses, parapets, coping, bed blocks, anchor blocks, plain window sills, fillets, sunken floor etc., up to floor four level, excluding the cost of centering, shuttering and finishing: 1 :2:4 (1 Cement : 2 coarse sand (zone-Ill) : 4 graded stone aggregate 20 mm nominal size) (HSR 6.2.2)

Cutting holes up to 23 cm through stone masonry or brick work in cement walls for pipes and making good including repointing, replastering and finishing according to existing finish where required 11.43 cm thick wall (HSR 20.26.1)

22.86 cm thick wall (HSR 20.26.2)

Making connection with the existing G.I. branch main up to 40 mm size including cutting and threading pipe etc., complete excluding cost of tee and long screw, but including cartage of material to site (HSR 20.36)

Providing and fixing white vitreous chinaware laboratory sink with C.I. brackets, C.P. brass chain with rubber plug, 40 mm C.P brass waste and 40mm C.P. brass trap with necessary C.P. brass unions complete, including painting of fittings and brackets, cutting and making good the wall wherever required : Size 600x450x200 mm (HSR 22.6.2)

Providing and fixing 15 mm C.P. brass Laboratory cock swan neck of best quality (to the approval of Engineer-in-charge). One way (HSR 22.8.1)

Providing and fixing 40mm i/d G.I. waste pipe embedded in walls up to floor level including cost of union and plumber joint. (HSR 22.16)

Providing and fixing G.I. pipes complete with G.I. fittings and clamps, i/c cutting and making good the walls etc. Internal work· Exposed on wall 15 mm dia nominal bore (HSR 22.88.1)

20 mm dia nominal bore (HSR 22.88.2)

25 mm dia nominal bore (HSR 22.88.3)

Providing and fixing G.I. Union in G.I. pipe including cutting and threading the pipe and making long screws etc. complete (New work) : 25 mm nominal bore (HSR 22.94.3)

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end): 25 mm nominal bore (HSR 22.98.1)

Providing and fixing in position singel socket SWR UPVC soil waste or antisyphonage pipes as per IS 13592 of E.D.C manufacture or of any other reputed firm including cutting, jointing, wastage, but excluding cost of jointing. Single Socket Type B 90 mm o/d SWR UPVC pipe lines laid complete (HSR 22.222.2.3)

Supply and fixing of PVC floor traps (Heavy duty) of 90 mm i/dia outlet of Prince /Supreme/Skipper make, complete in all respect. (NS)

Supply of PVC specials of Prince / Supreme/Skipper make as per detail given below:- (NS) (i) Elbow 3" i/dia size

Supply and fixing of PVC door junction of of size 3" x 3" x 3" i/dia size of Prince/Suprem/Skipper make. (NS)

Supply and fixing of PVC plain junction of of size 3" x 3" x 3" i/dia size of Prince/Suprem/Skipper make. (NS)

Providing and fixing C.P. grating 100 mm dia size of best quality, complete in all respects.(NS)

Electrical work 54 to 82:- Supply and erection of PVC CONDUIT ISi marked (Medium) recessed in walVceiling etc. including the cost of PVC bends, inspection boxes, iron hooks and cement concrete etc. complete in all respect up to the entire satisfaction of Engineer-in-Charge of work. (HSR 23.7.6.2) 25 mm dia

Providing and fixing Piano type accessories of approved make in existing box and Bakelite sheet including fixing and making necessary connections, complete in all respect. Socket size rotary step type Electronic regulator for A.C. ceiling fan. (HSR 23.8.1.13)

Providing and fixing GI concealed sheet metal boxes with inner and outer face plate including concealing the box in wall and fixing in position with inner plate and face plate with all labour and material required for the job complete in all respects. 2 Modules ( HSR 23.8.10.1 )

6 Modules ( HSR 23.8.10.4 )

12 Modules ( HSR 23.8.10.6 )

Providing and fixing modular type accessories of approved make in existing box including fixing and making necessary connections, complete in all respect.( HSR 23.8.11.1 ) 5 amp. 1 way switch

15 amp 1 way switch (HSR 23.8.11.3)

5 amp Socket ( HSR 23.8.11.4)

Blinking plate ( HSR 23.8.11.10 )

Supply and erection of Modular case circuit breaker single pole/4 pole on existing wall/pedestal/Panel including bounding to earth and making necessary connections required to complete the job in all respect up to the entire satisfaction of the Engineer-in-charge of the work (HSR 23.22.1.4) :- 125amp to 160amp 415V 25KA 3Phase

Supply and erection of miniature circuit Breaker 240/415 V in the existing distribution board including making necessary connections:- :- (HSR 23.22.5.1) 6 to 32 amp. MCB SP

40 to 63 amp. MCB TPN ( HSR 23.22.5.8)

Supply of GI pipe (B-Class) for suspension rod of ceiling fan including threading if required:-( HSR 23.23.2.1 ) 15mm dia

Supply and erection of copper lugs including crimping etc. entire satisfaction of Engineer-in- Charge of the work.(HSR 24.2.6.4) 6 sqmm

SITC of wall / free standing floor mounting dust and vermin proof comopartmentalized cubical panel made out of 2 mm thick CRCA sheet, required hardware 3 mm thick Bkt sheet provided all along the bus bar and cable alley separating switches compartment and supporting suitable channel duly painted etc.( NS )

Supplying and fixing of copper bus bar duly tinned by means of SMC/DMC type insulator high tensile nuts and bolts spring washers fixing to same in existing panel including bending, cutting in required shape and size and insulation with colour coding heat shrinkable PVC insulation complete in all respect.( NS )

S/E of recessed type 42 watt full window glare free opal difffuse LED panel of size 595x595 mm suitable for Armstrong/POP/GB ceiling with M.S. Powder coated white housing. Total system lumen of 42 watt LED should be 4600 or above in cool day light (5600k to 6500k), Power factor >0.95, CRI (Ra) >80, LED lamp efficiency ≥140 lm/w, Average life >50000hours, complete with all accessories as required with connections. (Industrial)( NS )

SITC iof push ON/OFF type 25 A modular type motor starter switch (white color) for AC's including the cost of petty material required to complete the job upto entire satisfaction of Engineer-in-charge.( NS )

S/E of Propeller type AC ventalating fans ( exhaust fan ) with necessary earthing of fan complete with louver shutter , 380mm sweep 900RPM ( Heavy Duty ) Make Orient , Usha , Khaitan , Crompton (NS)

Providing and installing split type air conditioners fIVE star rating inverter type with copper coil 1.5 ton capacity +/-10% fitted with super tropical - DC PAM inverter - return cooled - rotary compressor operating on referigerant R-410A suitable for wall mounting confirming to IS : 1391 ( Part - 2 ) / 92 ( Execpt power consumption Eachrms with upto date amendments suitable for operating on 230 volts 50Hz single phase A.C supply having following specifications :- i) Cooling Coil row - 3 Eachs. ii) Air Flow ( CMH ) - 1000 cum / hr iii) Sound Level ( H/M/L ) - 45/38/26 iv) Louvers Swing - 3D+3D Auto etc. complete in all respect. Make O General / Hitachi / Mitsubishi ( Heavy Industries ) Five Star Rating Model as approved by the Engineer in Charge. (NS)

Providing and installation of automatic voltage stablizer of Single Phase 5.00KVA capacity copper wound heavy duty 100volt up of Logicstate/Voltage/Bluestar/V -guard make ISI marked complete in all respect. (NS )

Providing and fixing in position powder coated MS stands for outdoor units including suitable nuts & bolts etc. of best quality complete in all respect. (NS)

Providing and fixing extra copper tubing / referigerant pipe for above split air conditioners consisting of inlet , outlet pipes , insulation and electricwiring etc as per requirement complete in all respect beyond 4.0 meters length (NS)

S/E of surface/wall mounted ≤20W integrated LED 4 feet fitting with Epoxy Powder coated white/Grey extruded aluminium channel housing for efficient heat dissipation. Total system lumen of 20 watt LED should be ≥ 2000 or above in cool day light (5700K to 6500K), Power factor >0.95, CRI >80, Average life >50000 hours. Complete with mounting Brackets & accessories as required with connections(Industrial) Make: Philips, Havells, Wipro, Bajaj. (NS)

S/E of AC ceiling fan capacitor type complete with shackle, 300mm down rod and regulator etc. {NS} i) 1400mm sweep. Make: Usha, Orient, Crompton.

S/E of PVC unsheathed copper conductor cable single core 1100 volts grade in pipe of suitable size excluding cost and erection of pipe. (NS) Cable Size 1.5 Square meterm (3/0.81)

Cable Size 2.5 Square meterm (3/0.81)

Cable Size 6 Square meterm (7/1.05)

Cable Size 10 Square meterm (7/1.35)

nagpal and company

Bansal enterprises