SPECIAL REPAIR TO 16 X GUARD POST OF 4 ASD AT NAGROTA UNDER GE (P) NAGROTA

Amount

Taking down chowkats or frames but with shutters (without taking off shutter from the frames) not exceeding 1.5 sqm each complete all as specified and directed

Taking down chowkats or frames but with shutters (without taking off shutter from the frames) exceeding 1.5 sqm but not exceeding 4 Sqm each complete all as specified and directed

S&F factory made pressed steel frames of size125 x 60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified.

Supply and fixing factory made, HDF prelaminated moulded door shutter, 35mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick 3D wood grain moulded PVC sheet on the front face and 2mm plain colour PVC sheet on back face, supplied and fixed to frame at site all as per specification and drawing No-CEUZ/TD-1343/2013 sheet 1/1, complete all as specified.

Supply and fixing single piece wire guazed factory made, HDF prelaminated moulded door (stile) with 2,4, or 6 pannel design including GI wire guage complete, supplied & fitted in the frame at site as per specification and drawing No-CEUZ/TD-1343/2013 sheet 1/1, complete all as specified.

S & F solid PVC door frames of sizes 50mm x 47mm made out of 5mm but single side prelam PVC sheet used instead of Plain colour PVC sheet & edges will be painted to match with prelaminated sheet reinforced with MS Square tube complete all as specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (stile) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded but single side pre laminated PVC sheet used instead of Plain colour on both faces PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement in the frame at site as per specification.

Box Type Steel window side hung double shutters with provision for desert cooler/AC (inside for wire mesh & out side for glass) including guard bars, hinges, Tower bolt and steel peg stay complete with glazing bar dovetailed or welded and fixed, steel ventilator shall be conforming to relevent IS complete all as shown on drawing No CEUZ/TD/1302/09, Sheet No 1/3 to 3/3 and directed. Note :- Wire mesh and sheet glass shall be measured and paid separately.

Box Type Steel ventilators top hung double shutter (inside for wire mesh & out side for glass) including guard bars, hinges, Tower bolt and steel peg stay complete with glazing bar dovetailed or welded incuding a coat of red oxide after preparation of surface before fixing steel window shall be conforming to re relevent IS complete all as shown on drawing No CEUZ/TD/1302/09, Sheet No 1/3 to 3/3 and directed. complete and directed. Note :- Wire mesh and sheet glass shall be measured and paid separately.

M & L two coats of synthetic enamel paint over one coat of red oxide primer including preparation of new or untreated steel surfaces of any description not otherwise described over 10cm width or girth complete all as specified .

S&F 200mm Mild steel sliding door bolts, plate type, stove enamelled black, with bright bolt not less than 12mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified.

S&F 150mm Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast-aluminium alloy and fixed complete all as specified.

S&F 200mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

S&F 150mm long aluminium handle cast type anodised complete all as specified and directed.

S & F 125mm long aluminium handle cast type anodised complete all asspecified and directed.

S & F Butt hinges 125 mm size, medium weight cold rolled mild steel hinge pin, and fixed complete all asspecified and directed.

S & F Butt hinges 100 mm size, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-21 complete all asspecified and directed.

S & F 3.0mm thick sheet glass ordinary quality and glazing with oil putty fixed with bends glazing pins required in square not exceeding 0.50 Sqm in each panes completed all as specified and directed.

S & F 3.0mm thick figured glass pinhead type and glazing with oil putty fixed with bends glazing pins required in square not exceeding 0.50 Sqm in each panes completed all as specified and Directed.

S & F stainless steel wire cloth 0.36mm nominal dia and average width of aperture 1.40mm and fixed with stainless steel wire staples completed all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floor and pavings not exceeding 15cm thickness (below or above ground level) complete all as specified and directed.

M&L for 75 mm thick PCC1:3:6 type C-2(using 40mm graded aggregate) as in plinth protection & finishing the surface even & fair whtiout using extra cement complete all as specified and directed.

M&L 40mm thick PCC (1 : 2 : 4) type B-1 as in floor & finishing the surface even & smooth using extra cement etc complete all as specified and directed.

M&L Glass dividing strips, 3 mm thick and 38 mm wide and inserted in position to conform to design complete all as specified and directed.

Dismantling of floor hearth and wall tiles including cement mortar bedding but not backing and removing rubbish outside the MOD land complete all as specified and directed.

M & L 15 mm thick screed bed or bedding layer in cement mortar 1:6 for laying floor finishes completed all as specified and directed.

M&L non-skid, ceramic, joint free coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles as specified and directed.

M & L 10mm thick rendering on fair faces of brick work or concrete surface in CM 1:3 for laying wall tiles completed all as specified and irected.

M & L Glazed ceramic coloured tiles 350 x 250 x 7mm or 450 x 350 x 7mm thick in vertical surfaces, set & jointed in neat cement slurry and pointed with coloured cement to match in skirting / dados completed all as specified and directed.

M &L of Machine cut kota stone slab flooring 18-20mm thick laid and jointed with grey cement slurry mixed with pigment to match the shadeof the stone including grinding and polishing(Mirror finish) over cement screed bed 20mm in cement mortar 1:4 as in floor finish including roughening of existing surfaces and applying a coat of cement slurry @ 3 Kg/sqm of surface complete all as specified

M &L of Machine cut kota stone 18-20mm thick in skirting , dado, riser and pillar laid and jointed with grey cement slurry mixed with pigment to match the shade of the stone including grinding and polishing (Mirror finish) over cement 10mm rendering in cement mortar 1:3 as in vertical surfaces including roughening of existing surfaces and applying a coat of cement slurry @ 3 Kg/sqm of surface complete all as specified

Demolition of brick work or stone boulder masonary built in cement mortar completed all as specified and Directed.

M & L Brickwork with subclass ‘B’ bricks, straight or curved on plan to any 6m radius in walls built in cement Mortar 1:6 complete all as specified and directed.

Taking down cement plaster on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

M&L 15mm thick rendering on fair faces of brick work or concrete surface in CM 1:4 to be finished even and smooth with out using extra cement using WPC as per manufacturing instruction complete all as specified and directed. Note:- WPC shall be measured and paid separately.

M&L 10mm thick rendering on fair faces of brick work or concrete surface in CM 1:6 to be finished even and smooth without suing extra cement complete all as specified and directed.

M&L rendering 5mm thick in CM 1:3 and finishing the surface even and smooth without using extra cement as in ceiling, soffits of slab complete all as specified and as directed.

M&L preparing new plastered surfaces of wall and applying two coats of distemper oil emulsion over a coat of primer & putty complete all as specified and directed by Engineer in charge.

M & L preparing new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed by Engineer in Charge.

M & L preparing new plastered surfaces of ceiling and applying three coats of white wash on ceiling surfaces complete all as specified and directed Engineer in Charge.

Complete removal of existing treatment on old surfaces on walls and applying two coats of distempering on walls with distemper oil emulsion over a primer & putty complete all as specified

M&L two coats of white wash on old surfaces on ceiling including preparation of old surfaces complete all as specified and directed by Engineer in Charge.

M & L Complete removal of existing treatment on old surfaces on walls and applying two coats of cement base paint over a coat of primer & putty including preparation of old surfaces complete all as specified and directed by Engineer in Charge.

Taking up or down steel tubing & connections including cleaning for refixing on removal to store-15mm bore dia of pipe complete all as specified and directed.

Taking up or down steel tubing & connections including cleaning for refixing on removal to store-20mm bore dia of pipe complete all as specified and directed.

S & F 15mm bore of tube medium grade galvanized (ISI Marked) with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Refixing old steel 15mm bore of tube with all fittings & fixed in new or old position complete to walls & ceiling or laid in floors complete all as specified and directed.

S & F 20mm bore of tube medium grade galvanized(ISI Marked) with all fittings & fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

Refixing old steel 20mm bore of tube with all fittings & fixed in new or old position complete to walls & ceiling or laid in floors complete all as specified and directed.

Supply only integral water proofing compound ISI Marked complete all as specified.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings, heads, shoes, bends, swan-necks, etc., including cleaning or refixing or removal to Store (measured overall as fixed along the centre line over fittings and accessories complete all as specified

S&F PVC (SWR) pipes single socketed waste and vent pipes 75mm dia bore in any length with rubber ring joints laid in floor complete all as specified

S&F PVC (SWR) pipes single socketed waste and vent pipes 110mm dia bore in any length with rubber ring joints laid in floor complete all as specified.

S&F PVC (SWR) rain water pipes single socketed waste and vent pipes 110mm dia bore in any length with rubber ring joints fixed to wall complete all as specified.

S&F PVC (SWR) bend with Access door any radius 75 mm completed all as specified and directed.

S&F PVC (SWR) bends any radius 75 mm completed all as specified and directed.

S&F PVC (SWR) bends any radius 110 mm complete all as specified and directed.

S&F PVC (SWR) bend with Access door any radius 110 mm completed all as specified and directed.

S&F PVC (SWR) vent cowl 110 mm complete all as specified and directed.

S&F 75 mm PVC (SWR) floor trap, plain with grating including jointing with solvent cement complete all as specified and directed.

S&F in repair PVC (SWR) gully trap 125/110 mm, setting and jointing with solvent cement complete all as specified and directed.

S& F in repair Vitreous China urinals, Bowl type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2, securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. (Exclusive of fixing supply pipe to flushing cistern, trap and waste pipe) complete all as specified and directed.

S&F in repair Vitreous China wash basin, white, flat back, size 450x300mm with low density polyethylene (LDPE) pipes 32mm of pressure rating 6 kg/sqm of adequate size and length and excluding taps, waste, chain and plug and porcelain stopper but including brackets complete all as specified and directed.

S&F in repairs, Brass chromium plated shower rose 125mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

S&F in repair bib taps 15mm bore cast copper alloy with crutch or butterfly handle, screwed down, screwed for iron pipe complete all as specified and directed.

S&F stop valve 15mm bore cast copper alloy with screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions completed all as specified and directed.

S&F vitreous China squatting pan, 'Orissa' pattern, size 580mm x 440 mm, white with integral foot rest and 'P' or 'S' trap, including provision of lime concrete bedding, connection to trap and flushing pipe etc complete all as specified and directed.

S&F in repair 10 litres capacity PVC valveless syphonic dual type action type, flushing cistern (ISI marked), low level with inlet, ball valve, float bracket & flush pipe complete all as specified & directed.

S&F in repair CP Grating 100 mm dia complete all as specified and directed

S&F in repair PVC connections 15mm size with PTMT nuts of length 600mm complete all as specified and directed

S&F in repair Pillar taps cast alloy with capsten head screwed down high pressure with or without lettered 'Hot' or 'Cold' with long screwed shanks and fly-nutsscrewed for iron pipe and fixed Complete all as specified and directed.

S&F in repair chromium plated Tubular towel rail, 20mm dia, D type, 60cm long between flanges complete all as specified and directed.

Supply and fixing Soap dish, vitreous China white, of approximate size 160 x 160 x 90mm complete all as specified and directed.

S&F rotational moulded polyethylene water storage tanks 500 Ltr capacity (Cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR part-I and dismantling of old water tank complete all as specified and directed.

S F in repair 20mm Ball valves high pressure of PTMT with epoxy coated Aluminium rod & high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 32mm Waste coupling of PTMT (half or full threaded) . (Minimum weight 32mm45gms/40mm-60 gms complete all as specified and directed.

Demolition of cement concrete of any description over roof treatment and in any position not otherwise specially provided complete all as specified & directed.

Taking down existing water proofing treatment complete including removal of debris outside the MOD land complete all as specified and directed

M&L 10 mm thick plastering in cement mortar 1:3 mixed with water proofing treatment finished even & smooth over PCC padding while the concrete is green complete all as specified.

Apply a coat of bituminous primer conforming to IS-3384 @ 0.4Kg/Sqm on the prepared surface of plaster. After drying of primer, apply a coat of hot blown VG 20 paving grade (60-80 penetration) bitumen conforming to IS-702 @ 1.2 Kg/Sqm of plastered surface completed all as specified and Directed.

M&L APP polymeric membrane minimum weight 3 Kg/Sqm and minimum 3mm thick reinforced with polyster non woven fabric (weight not less than 150 gms/Sqm) laid with 75 mm side overlaps and 100 mm end overlap, the membrane has to be laid with LPG torch and over lap sealed and finished near over roof including a coat of bitumen VG 20 @ 1.20 Kg per sqm over APP membrane and blinded with fine sand in dry condition @ 0.50 Kg/Sqm dusted over the bitumen coat complete all as specified and directed by Engineer in charge.

M& L for Cement concrete tiles 25cm x 25cm x 22mm thick, machine pressed; set jointed and pointed in neat cement slurry in floors, and cut and polished cement slurry in floors with grey cement and no pigment over 15 mm thick screed bed in cement mortar 1:4 mixed with creosote oil and flush pointed in CM 1:3 complete all as specified and directed

M & L PCC 1:2:4, type B-0, (using 12.50 mm graded stone aggregate) as in under layer of waterproofing treatment to provide gradient and slope and finishing the surfaces rough to receive mortar complete as specified and directed.

S & F for framed work such as grills, gratings, etc.. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work MS round/square bar conforming to Fe.290.Gde-E-165 complete as specified and directed.

M & L Cutting holes not exceeding half brick walls in cement mortar for inserting holdfasts and making good dismantled portion in cement mortar 1:3 or cement concrete 1:2:4 Type B-1 as required complete as specified and directed.

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified

M&L RCC type B1 1:2: 4 (using 20 mm graded crushed stone aggregate) as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, chajjas canopies, deck slabs and in shelves and the like complete as specified and directed.

S & F TMT Bars Mild steel bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welding with existing reinforcement in repairs complete all as specified and directed.

S & F TMT Bars Mild steel bars but 6mm to 8mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips or welding with existing reinforcement in repairs complete all as specified and directed.

S&F Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings, Chajjas and similar work; not exceeding 200mm thick (Horizontal or sloping) rough finished surfaces of concrete complete all as specified and directed.

S&F Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves, slabs, chajjas etc. including supports, overhangs, etc. complete all as specified and directed.

S&F UPVC Pipes single sockted waste and vent pipes 150mm dia bore in any length with rubber ring joints laid in floor complete all as specified.

M&L concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete 1:3:6 type C-2 for 150mm dia complete all as specified.

M&L PCC 1:2:4 type B-1 using 20 mm graded crushed stone aggregate as in benching ,coping etc. including necessary formwork complete all as specified and directed.

M&L Precast cement concrete 1:2:4 type B-1 using 20mm greaded crushed stone aggregate in manhole /drain cover slab complete all as specified and directed.

Cleaning /clearing of sewage line (including manhole except 1st manhole) 100mm to 350mm bore of any description under ground any depth, removing any type of blockage including desilting , descaling and de-choking from drains as well as from manhole with combined high pressure vacuum water jetting cum suction (vacuum) type machine mounted on LMV/HMV having facility of high pressure vacuum including provision of hydraulic application through high pressure thermoplastic fiber based water jetting hose and through conical round shaped nozzle pile and flushing after cleaning including clearing of manhole, sludge water shall be disposed as directed including taking of manhole cover and refixing the same after cleaning complete all as specified.

Cleaning /clearing of sewage line ( 1st manhole) any depth, any size , taking out water mixed with sludge and soild sludge including any foreign materials such as stones, tree hedges etc, removing and depositing sludge at a distance not less than 20 m in a ditch including necessary excavation of pits and covering with earth & sparying unslaked lime on the covered ditch as well as around the manholes to make hygenic including necessary flushing of manholes with watering after desludging complete all as specified.

Desludging the solid sludge from septic tank, soakage well inlet/outlet chamber , removing out all scum, silt reduce sludge (both organic/inorganic nature) after plugging the incoming sewage line through combined high pressure water jetting cum suction (Vacuum) type machine mounted on LMV/HMV and facility of high pressure vacuum and removing and dumping off the same in the tank to a place out side contonment at the place marked for the purpose by local municipality or area controlling complete as specified and directed.

M&L for chequered cement concrete tiles 20cm x 20cm x 25mm thick, set, jointed and pointed in neat cement slurry in floors with grey cement and no pigment over 20 mm thick screed bed in cement mortar 1:4 over 100 mm thick PCC 1:3:6 type complete all as specified

S&F in repairs 20mm dia bore of ISI marked gun metal,globe or gate valve with iron wheel head,screwed both ends for iron pipe of high pressure complete all as specified and directed by Engineer-in-Charge.

Taking down carefully unserviceable Aluminium point wiring complete (light, fan socket, bell or power) with fitting such as switches, ceiling rose lamp holder, regulators, sockets, light fittings etc. and keeping in safe custody for taking credit complete all as specified and as directed by Engineer-in-Charge

Taking down ceiling fan any sweep, removing blades ,cleaning the fan completely for dust and dirt as well as oiling & greasing and hanging the same back to its original positions including connecting with three core flexible copper wire to ceiling rose etc after the completion of the point wiring including replacement of old unserviceable fan hook, rubber pad, nut bolts and washers etc, complete, all as specified and directed by Engineer-In-Charge.

Taking down unservecable MCB DB SPN with MCB's of any make / capacity complete all as specified and directed by Engineer-in-Charge.

M&L for point wiring with PVC insulated unsheathed 1100 volt grade FRLS cable with multi stranded copper conductor of size 1.5 Sq mm (Nominal area) drawn through and including non metallic rigid PVC conduit medium grade ISI marked not less than 20mm dia ,concealed in wall and surface on ceiling with all conduit fittings & fixing acessories inculding sunken anodised pressed steel terminal box not less than 1.2mm thick covered with 3 mm thick plastic laminated sheet cover of suitable size with brass screws for mounting switches, sockets, regulators with and including 1.5sqmm FRLS multi stranded copper conductor drawing as continuous earth wire connected to main earth and earth dolly complete all as specified for the following :-

(a) One light point controlled by one switch 5 Amp.

(b) One ceiling fan/exhaust fan point controlled by one switch 5Amp

(c) One socket out let 5Amp controlled by one switch on same board.

(d) One socket out let 5 Amp controlled by one switch on independent board.

All as per item No 109 here in before but point wiring with 2.5sqmm FRLS multi stranded copper conductor cable for main circuit and 2.5sqmm cable as earth continuity conductor for one 15Amp socket out let controlled by one 15Amp switch on independent board.

S&F switch piano flush type 5 Amps single pole one way complete,

S&F switch socket combination 2 in 1, 3 pin, 5 Amp flush type complete.

S&F switch socket combination 2 in 1, 5 pin, 5 /15 Amps flush type complete.

S&F of ceiling rose 3 terminal complete PVC/Polycarbonate isolated boly complete all as specified and directed.

S&F stepped type electronic fan regulator flush type 230V, 50 Hz, AC supply, on the existing phenolic laminated sheet etc as required all as specified and directed.

M&L aluminium CRCA Batten channel fitting with LED tube 18 watt complete with all accessories and including connecting up with three core twisted flexible copper conductor cable with suitable size of 230V 50 Hz complete all as specified. Make:- Bajaj, Cat part no. 112181 BLRB-DB 118 (for batten fitting) & Cat Part No. BLRB18W CW (for LED 18 Watt) or equivalent from the makes given in particular specifications.

M&L LED light fitting 1x9W bulk head luminaries IP 65 complete with all accessories including LED lamp 9 watt , connecting up with twin core twisted flexible copper conductor cable with suitable size of 230V 50 Hz .

S&F for lamp holder PVC/polycarbonate type with back plate suitable for batten fittings complete all as specified and directed. Make:- Anchor (Penta) or equivalent model of Cona/Havells/HPL or equivalent from the makes given in particular specifications.

S&F for LED bulb 9 watt complete all as specified and directed. Make-Havells Cat part No LHLDEUEEML8R009 or equivalent from the makes given in particular specifications.

S&F sheet metal enclosure distribution board SPN 8 way 230 V, 50 Hz, double door with neutral, Earthing bar and din rail complete all as specified and directed.

S&F MCB DP 32 Amps 10 KA 230 volts "C" series complete. Makes : HPL Cat No NTDPC32 or equivalent from the makes given in particular specifications.

S&F MCB single pole 6 to 32 Amps 10 KA 230 volts "C" series complete Makes :HPL Cat part No-NTSPC06-32 or equivalent from the makes given in particular specifications.

M&L for earthing complete for bldg with galvanized mild steel earth plate electrode 60cm x 60cm x 6mm thick buried directly in ground (earth pit not less than 2.25 meters below ground level) with top edge of earth plate not less than 1.5 meters below ground level connected to galvanized earth wire 4.00 mm dia by means of nuts, bolts, thimbles, chuck nuts, washers of GI or steel, PCC (concrete chamber of size 300 mm x 300 mm x 300 mm inside dimension) shall be PCC 1:3:6 type C-1 using 20mm graded stone aggregate with fair finish , internal surface of concrete chamber shall be given 15mm thick plaster in CM 1:4, funnel with wire mesh of 22 gauge, 80 mm thick PCC pit cover 320 mm x 320 mm of RCC 1:2:4 type B-1 using 20 mm graded stone aggregate reinforced with XPM, JALLI pit shall be filled with charcoal dust and common salt all as shown in electrical plate No 5 of MES SSR Part-I (1991) as specified including provision of 15mm dia medium grade GI pipe for earth wire protection and 20 mm dia for watering complete , all excavation and earth work & connecting the earthing to an earthing test point / main switch board as specified and testing on completion complete.

Supply and laying or fixing or passing through pipe 1100 volts grade heavy duty electric cable with XLPE insulated screened PVC bedded aluminium stranded conductor served with inner sheathing of PVC tape armoured with galvanised steel wire or tape and over all PVC sheathed of size 10 Sqm x 2 core, complete all as specified and directed.

M&L Excavation in trenches, not exceeding 1.5 M wide and not exceeding 1.5 M depth for foundation, for laying underground cables, poles and stays etc., and getting out in any type of soil complete all as specified and directed.

M&L Returning, filling in, including spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soils complete all as specified and directed.

M&L Removing Excavated soils not exceeding 50 M and depositing where directed at a level not exceeding 1.5 M above the starting point complete all as specified and directed.

Sand cushioning to under ground cable provided with a layer of 8cm deep before laying the cable and 15cm deep after laying and stretching the cable.

Brick covering with width equal to length of brick as mechanical protection to cables with well burnt sub class 'B' bricks laid dry flat all as directed.

Steel tubing galvanized (light grade) 40 mm bore conforming to IS-1239 for passing cable under road/floor or fixing to poles for protection of under ground cable complete with Flat iron 50x6mm clamps made to shape and 12mm dia bolts, nuts and washers for fixing where required complete all as directed by Engineer-in-Charge

Note:- Schedule of credit Rs. 52,624.00 will be deducted from total amount quoted while accepting the bid. Details of schedule of credit is given in tender documents.

ASHWANI KUMAR KHAJURIA AND SONS

RAJINDRA ENGINEERS & CONTRACTORS