Increasing capacity 1x5 MVA to 1x10 MVA at 33, 11 Sub-Station NAUJHIL Distt.- Mathura on Semi-Turnkey Basis

Amount

SUB-STATION PART:- 33 KV Line Isolator.

33 KV Bus Isolator.

33 KV Lightening Arrestors

33/11 KV Transformer 10 MVA

33 KV VCB 800A, 750MVA with Steel structure

Control panel I/C for 33 KV single T/F

33 KV CT 200/100/1-1A

33 KV 1 Ph PT 33 KV/110 V

33 KV Terminal Gantry with Plinth & Foundation as per RESSPO Schedule

Structure for Line & Bus Isolator. with Plinth & Foundation

33 KV Post Insulator

Structure for Post Insulator with Plinth & Foundation

Structure for Lightening Arrestors with Plinth & Foundation

90 Lbs. Rail pieces for T/F

CT Steel structure with Plinth & Foundation

Structure for P T with Plinth & Foundation

33 KV Fuse Set

Structure for fuse Set with Plinth & Foundation

Control cable:- (i) 4 × 2.5 Sq.mm.

(ii) 2 × 2.5 Sq.mm.

Earthing of Sub-Station:-(As per RESSPO Schedule) (i) Outdoor Equipment (Earth Mat)

Water level Pipe Earthing for Power T/F

Chemical Pipe Earthing

Alluminium Paint for painting of Sub-Station Structure & equipment.

Red Oxide Paint for painting of Sub-Station Structure & equipment.

Power Transformer Plinth of size 3.46 x 4.46 Mtr. Having 0.5 mtr. below ground level and 0.5 Mtr. above ground Level with Transformer Cable Stand made by G.I. 65x65x6 mm 3.00 Mtr. Long angle with use of flat 50x6 mm piecees and 100x50x6 mm L-shape channel for Power Transformer nutral earthing

Plinth & Foundation of 33 KV VCB

Dismental & Uninstalling charges of 1x5 MVA TF from Plinth to Safe Place at Sub-Station

33 KV LINE PART:- 9.0 Mtr. long P.C.C. Pole

11 Mtr. long S.T. Pole

33 KV Pin Insulator

33 KV Pin with nut

Earthing complete

Disc Insulators B&S Type 7000 Kg.

Disc Fittings for Dog/Raccoon 7000 Kg.

Stay Set Complete (G.I STAY ROD , 20X1800 MM ,STAY WIRE 7/8 SWG, STAY CLAMP,BOLT NUT & WARSHER)

Grouting of stay rods 1800 x 20 mm. including all works of excavation, fixing, tightening & nozzling of stay with the poles and of required tension as per relevant drawing including back filling of earth and proper ramming.

Stone Pad

Barbed wire

The Grouting and making of plinth of the support (1/6 of the full length of the supports) will be done as per norms in the CC 1:4:8 with cement, course sand and brick ballast including back filling and proper ramming.fixing of all clamps and other accessories as per relevant drawing. i) 9 Mtr. Long SP-55 poles

ii) 11 Mtr. Long SP-55 poles

Alluminium Binding wire 6 SWG

Number Plate with Clamp.

Danger Board with clamp

M.S. Bolts, Nuts & Washers

Aluminum Paint

Red Oxide

Earth wire clamp with nut & bolt

Top Channel 125x65x3200 mm. with Clamps

M.S. Angle 65 x 65 x 6 x 4300 mm. x 2 Nos. Bracing with 4 Nos.Clamps.

P.G. Clamp for Dog Conductor

‘E’ Bracket for 33 KV

Droper Channel 100 x 50 x 3000 mm.with .Clamps. ( for Cable supporting )

Bus Bar Gantry

M.S. Angle 50 x 50 x 6 mm., 2.350 M.

Concreting 1:3:6

ACSR Dog conductor

P.G. Clamp for ACSR Dog Conductor, L.I.,B.I.,L.A., T/F, Bus Bar etc.

Carriage of following material from Center Store to Site SUB-STATION PART:- 33 KV Line Isolator.

33 KV Bus Isolator.

33 KV Lightening Arrestors

33/11 KV Transformer 10 MVA

33 KV VCB 800A, 750MVA with Steel structure

Control panel I/C for 33 KV single T/F

33 KV CT 200/100/1-1A

33 KV 1 Ph PT 33 KV/110 V

33 KV LINE PART:- 9.0 Mtr. long S.T. Pole

11 Mtr. long S.T. Pole

Shanti Enterprises