Civil and allied electrical works for addition of amenities infrastructure facilities and allied services including statutory and fire safety requirement for B- type multistory building at HAL Township Lucknow.

Surface dressing of the ground including removing vegetation and in-equalities not exceeding 15 cm deep and disposal of rubbish, lead up to 50 m and lift up to 1.5 m.

Earth work in excavation in all kinds of soil by mechanical means (Hydraulic excavator) /manual means over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and for all lift, as directed by Engineer-in-charge. All kinds of soil

Earth work in excavation in all kinds of soil by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, for all lift, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth, consolidating each deposited layer by ramming and watering, lead up to 50 and for all lift.

Excavating, supplying, stacking and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in foundation trenches, plinth, sides of foundation etc. complete for all lift.

Excavating trenches by mechinical / manual means of required width for pipes, cables, etc including excavation for sockets, and dressing of sides, ramming of bottoms, for all depth, including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth, including consolidating each deposited layer by ramming, watering, etc. and disposing of surplus excavated soil as directed, within a lead of 50 m : Pipes, cables etc. exceeding 80 mm dia. but not exceeding 300 mm dia.

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand)

Providing and laying Half brick masonry with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level. Cement mortar 1:4 (1 cement :4 coarse sand)

Providing and fixing pre-moulded joint filler in expansion joints of RCC roads / CC pavements after making the joints dust free with high pressure air jet cleaners, all complete as per direction of the Engineer-in-Charge. (Pre-moulded joint fillers shall be made of bitumen hot sealing compound impregnated fibre board having impregnation more than 35%, conforming to IS:1838 for fibre board and IS: 1834 for hot sealing bitumen compound grade A.)

Providing and laying factory made chamfered edge Cement Concrete 80 mm thick C.C. paver block of M-35 grade with approved colour design and pattern. in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge.

Providing and fixing at or near ground level precast cement concrete in kerbs, edgings etc. as per approved pattern and setting in position with cement mortar 1:3 (1 Cement : 3 coarse sand), including the cost of required centering, shuttering complete.:1:1½:3 (1 Cement: 1½ coarse sand(zone-III) derived from natural sources: 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete work in string courses, bands, chamber covers, copings, bed plates, anchor blocks, plain window sills and the like, including the cost of required centering, shuttering but , excluding cost of reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing and laying in position Concrete of M25 grade with minimum cement content of 330 kg /cum for all works up to plinth level, ready mixed or site batched design mix cement concrete for reinforced cement concrete work; using coarse aggregate and fine aggregate derived from natural sources, Portland Pozzolana / Ordinary Portland /Portland Slag cement, admixtures in recommended proportions as per IS: 9103 to accelerate / retard setting of concrete, to improve durability and workability without impairing strength; including pumping of concrete to site of laying, curing, carriage for all leads; but excluding the cost of centering, shuttering, finishing and reinforcement as per direction of the engineer-in-charge; for the following grades of concrete. Note: Extra cement up to 10% of the minimum specified cement content in design mix shall be payable separately. In case the cement content in design mix is more than 110% of the specified minimum cement content, the contractor shall have discretion to either re-design the mix or bear the cost of extra cement.

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

column

Suspended floors, roofs, landings, balconies and access platform

Edges of slabs and breaks in floors and walls Under 20 cm wide

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto and above plinth level with Thermo-Mechanically Treated bars of grade Fe-500D or more.

Providing and laying Cement concrete flooring 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate) 40 mm thick with 20 mm nominal size stone aggregate finished with a floating coat of neat cement, including cement slurry, but excluding the cost of nosing of steps etc. complete.

Extra for providing and mixing water proofing material in cement concrete work in doses by weight of cement as per manufacturer's specification

Providing and applying integral crystalline slurry of hydrophilic in nature for waterproofing treatment to the RCC structures like retaining walls of the basement, water tanks, roof slabs, podiums, reservior, sewage & water treatment plant, tunnels / subway and bridge deck etc., prepared by mixing in the ratio of 5 : 2 (5 parts integral crystalline slurry : 2 parts water) for vertical surfaces and 3 : 1 (3 parts integral crystalline slurry : 1 part water) for horizontal surfaces and applying the same from negative (internal) side with the help of synthetic fiber brush. The material shall meet the requirements as specified in ACI-212-3R-2010 i.e by reducing permeability of concrete by more than 90% compared with control concrete as per DIN 1048 and resistant to 16 bar hydrostatic pressure on negative side. The crystalline slurry shall be capable of self-healing of cracks up to a width of 0.50mm. The work shall be carried out all complete as per specification and the direction of the engineer-in-charge. The product performance shall carry guarantee for 10 years against any leakage.

For vertical surface two coats @ 0.70 kg per sqm per coat

For horizontal surface one coat @1.10 kg per sqm.

Providing and rendering 12 mm thick Cement plaster 1:3 (1 cement: 3 coarse sand) admixed with water proofing comound finished with a floating coat of neat cement.

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:6 (1 cement: 6 coarse sand)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes (Internal work - Exposed on wall), having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge.

20 mm nominal dia Pipes

25 mm nominal dia Pipes

32 mm nominal dia Pipes

40 mm nominal dia Pipes

50 mm nominal dia Pipes

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge.

65 mm nominal dia Pipes

80 mm nominal dia Pipes

100 mm nominal dia Pipes

Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) :

40 mm nominal bore

50 mm nominal bore

65 mm nominal bore

80 mm nominal bore

Providing and fixing gun metal non- return valve of approved quality (screwed end) :

65 mm nominal bore (Horizontal)

65 mm nominal bore (vertical)

80 mm nominal bore (Horizontal)

80 mm nominal bore (vertical)

Providing and Placing in position suitable PVC water stops (Dumb bell with central bulb (180 mm wide, 8 mm thick) conforming to IS:12200 for construction/ expansion joints between two RCC members and fixed to the reinforcement with binding wire before pouring concrete etc. complete :

Providing and laying in position cement concrete of specified grade 1:2:4 (1 cement : 2 coarse sand (zone-III) derived from natural sources : 4 graded stone aggregate 20 mm nominal size derived from natural sources) excluding the cost of centering and shuttering - All work up to plinth level :

Providing and laying matt finished vitrified tile of size 300x300x9.8mm having with water absorption less than 0.5% and conforming to IS: 15622 of approved make in all colours and shades in for outdoor floors such as footpath, court yard, multi modals location etc., laid on 20mm thick base of cement mortar 1:4 (1 cement : 4 coarse sand) in all shapes & patterns including grouting the joints with white cement mixed with matching pigments etc. complete as per direction of Engineer-in-Charge.

Providing and laying Vitrified tiles in floor Glazed Vitrified tiles Matt/Antiskid finish of size Size of Tile 600 x 1200 mm (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS:15622, of approved brand & manufacturer, in all colours and shade, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) jointing with grey cement slurry @3.3 kg/sqm including grouting the joints with white cement and matching pigments etc. The tiles must be cut with the zero chipping diamond cutter only . Laying of tiles will be done with the notch trowel, plier, wedge, clips of required thickness, leveling system and rubber mallet for placing the tiles gently and easily.

Providing and fixing factory made uPVC glazed/wire mesh windows/doors comprising of lead free uPVC multi-chambered frame, sash and mullion/coupler (where ever required) extruded profiles having minimum wall thickness of 1.70 mm for Series R1 and R2 profiles and 2.10 mm for Series R3 and R4 profiles conforming to EN: 12608 in any shape, colour and design duly reinforced with galvanized mild steel section made of required shape & size as per CPWD Specification, uPVC extruded glazing beads, interlocks and Inline sash adaptor (where ever required) of appropriate dimension, EPDM gasket, hardware, SS 304 grade fasteners of minimum 8 mm dia with countersunk head, comprising of matching polyamide PA6 grade sleeve for fixing frame to finished wall as per IS 1367 : Part 1 to 14, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame, sash & mullion (if required) shall be mitred cut and fusion welded/mechanically jointed duly sealed at all corners, including drilling of holes for fixing hardware and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of approved size and quality, all complete as per approved drawing conforming to CPWD specification & direction of Engineer-in-Charge. Section of steel reinforcement and cross sections of uPVC profiles to be as per design approved by Engineer-in-Charge. Wire mesh / Glazing of plain/ toughened/ laminated/ double glass unit with / without high performance coatings as per design requirements and conforming to IS: 3548 & IS: 16231 shall be paid separately.

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R2 series with frame (70mm & above) x (40mm & above) & both glazed and fly screen sash (25mm & above) x (50mm & above) with zinc alloy (zamak) powder coated touch locks with hook. (Height upto 1.2 metre).

Three track three panels sliding window with two glazed & one wire mesh panels with Aluminium channel for roller track, wool pile, nylon rollers with SS 304 body. Using R3 series with frame (98mm & above) x (40mm & above) & both glazed and fly screen sash (30mm & above) x (55mm & above) with zinc alloy (zamak) powder coated handle on every glazed panel along with multi-point locking system. (Height upto 1.8m).

uPVC Fixed window / ventilator with mullion / transom. Using R1 series with frame (33mm & above ) x (35mm & above) & mullion (33mm & above) x (50mm & above). (Height upto 0.90 metre)

uPVC Fixed window / ventilator with mullion / transom. Using R3 series with frame (55mm & above ) x (45mm & above) & mullion (55mm & above) x (65mm & above). (Height upto 2.5 metre)

Providing and fixing fly proof stainless steel grade 304 wire gauge, to windows and clerestory windows using wire gauge with average width of aperture 1.4 mm in both directions with wire of dia. 0.50 mm all complete. With 12 mm mild steel U beading

Providing and fixing glazing toughefened glass panes of 5 mm thickness in UPVC window, ventilator shutters and partitions etc.including cost of all labours, materials T&P all complete as per the architectural drawings and the directions of engineer-in-charge .

Providing and fixing M.S. grills of Fixed to steel windows by welding required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete.

Providing and fixing M.S. Tubular frames for doors, windows, ventilators and cupboard with rectangular/ L-Type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.Fixing with 15x3 mm lugs 10 cm long embedded in cement concrete block 15x10x10 cm of C.C. 1:3:6 (1 Cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size)

Providing and fixing ISI marked flush door shutters 30 mm thick including ISI marked Stainless Steel butt hinges with necessary screws conforming to IS : 2202 (Part I) non-decorative type, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters:

Providing and fixing wire gauge shutters 30 mm thick of Second class teak wood with ISI marked M.S. pressed butt hinges bright finished of required size using S.S. wire gauge of average width of aperture 1.4 mm in both directions with wire of dia 0.63 mm, for doors, windows and clerestory windows with hinges and necessary screws :

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge.

Providing and fixing aluminium sliding door bolts 250x16 mm, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts 250x10mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing aluminium tower bolts 150x10mm, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete :

Providing and fixing of bright finished Stainless steel door handle150 mm size including the cost of all necessary screws, labour, material T&P etc. complete

Providing and fixing aluminium hanging floor door stopper (Twin rubber stopper), ISI marked, anodised (anodic coating not less than grade AC 10 as per IS :1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.

Providing and fixing bright finished brass helical door spring (superior quality).

Providing and Fixing of Brass Chromium Plated (CP) Health Faucet of Parry/Cera/Johnson/somany as approved make with aprroximated 1.0 m. long fexible tube and wall holder, all complete including cost of all materials, labour, T&P etc as per specification, drawing and as directed by Engineer in charge.

Supplying and fixing of Brass chromium plated shower rose 125mm size with swivel joint including shower arm of Somany/Johnson/ Parryware/Cera make including the cost of all materials, labour, wastages, T&P etc., all complete as per specification and as directed by E.I.C.

Providing and fixing of, 15 mm dia CP Brass single hole swivel type swan neck basin mixer of approved quality and make of Johnson, Parry, Somany, CERA, including the cost of all approved materials, labour, wastages, testing,T&P at all heights etc., all complete as per specification and as directed by Engineer In Charge.

Supplying and fixing of Brass Chromium plated (CP) Kitchen Sink mixer for mixing hot & cold water screwed down for iron pipe and fixed of Johnson, Parry, Somany, CERA as approved make, including the cost of all approved materials, labour, wastages, testing,T&P at all heights etc., all complete as per specification and as directed by Engineer In Charge.

Providing and fixing 15mm nominal bore C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms.

Providing and fixing 15 mm dia CP Brass Single lever telephonic wall mixer of quality & make as approved by Engineer in charge.

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge.

Providing and fixing of White Vitreous China Wash basin size 550x400 mm with C.I. brackets, 32 mm CP brass waste of standard pattern , 15 mm dia CP Brass single hole basin mixer of approved quality and make, including painting of fittings and brackets, cutting and making good the walls wherever required:-

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) W.C. pan with ISI marked white solid plastic seat and lid , 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required :

Providing and fixing uplasticised 45 cm length, 15 mm nominal bore PVC connection pipe with brass unions

Providing and fixing 15mm nominal bore C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approved quality) complete with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete.

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour.

450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms

600 mm long towel rail with total length of 645 mm, width 78 mm and effective height of 88 mm, weighing not less than 190 gms.

Providing and fixing 600x120x5 mm glass shelf with edges round off, supported on anodised aluminium angle frame with C.P. Brass brackets and guard rail complete fixed with 40 mm long screws, rawl plugs etc., complete.

Providing and fixing cupboard shutter with 19mm thick one side decorative and other side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand including 2mm thick PVC edge banding tape with hot glue by edge bending machine etc. with auto closing spring loaded hinges (hydraulic type) etc. complete as per direction of Engineer-in-charge.(Payment of providing and fixing auto closing hinges shall be paid separately)

Providing and fixing 19mm thick both side balancing lamination factory pressed BWP grade marine ply as per IS 710 of approved brand boxes,shelves,racks,almirah,cupboard and drawer etc. including necessary nails,screws etc. complete as per direction of Engineer-in-charge.

Providing and fixing 1 mm thick 16 to 19mm wide PVC edge binding tape of approved quality for cupboard/wardrobe shutters including necessary synthetic resin hot pressed to edges on binding machine etc. complete as per directions of Engineer- in-charge.

Providing and fixing stainless steel soft closing spring hinges at 0 degree hinges (hydraulic type) of approved make/brand to cupboard shutters with full threaded steel screws including making necessary recess in board and finished etc. complete as per direction of Engineer-in-charge.

Providing and fixing magnetic catcher of approved quality in cupboard / ward robe shutters, including fixing with necessary screws etc. complete. Double strip (horizontal type)

Providing and fixing special quality chromium plated brass cupboard locks size 65 mm with six levers of approved quality including necessary screws etc. complete.

Providing and fixing stainless steel fancy handle 200 mm of approved make fixed with SS screws etc. complete as per direction of Engineer-incharge.

Providing and fixing stainless steel soft closing heavy type telescopic drawer channels of approved make 500 mm long with screws etc. complete as per directions of Engineer- in-charge.

Providing and fixing ready made 304 grade stainless steel Modular kitchen basket and accessories such as right angle basket (Plain Cup & Saucer, plant, Partition, Bottle rack, Thali, Cutlery) kitchen utensil basket, Dinner set basket, kitchen grain basket, Multipurpose basket as per site requirement including finishing (wherever required) and fittings. The same shall be fixed with necessary stainless steel nuts & bolts, Stainless Steel screws & telescopic channel etc. as per direction of Engineer-in-charge. (For payment purpose only weight of Stainless steel basket shall be considered excluding weight of all fixing accessories such as nuts, bolts, fasteners telescopic basket channels etc. Payment of providing and fixing telescopic channel shall be paid separately)

Providing and applying two or more coat of Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer's specification. New works (Two or more coat over and including water thinable priming coat with cement primer having VOC Content less than 50 gm/Lit.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade of approved brand of BERGER(Weathercoat Long Life 10)/ NEROLAC(Excel)/ ASIAN(Apex Ultima)/ DULUX(Weathershield) : New work (Two or more coats applied @ 1.43 ltr/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm) all complete inluding the cost of all labours, materials, T&P, cleaning the surfaces of application, scaffolding etc. and removing the debris & cleaning the respective areas all complete as per specifications and as directed by EIC.

Providing and painting with Hi gloss synthetic enamel paint of approved brand and manufacture of BERGER/ ASIAN/ NEROLAC/ DULUX of required colour to give an even shade : Two or more coats on new work over an under coat of suitable shade with ordinary paint of approved brand and manufacture all complete inluding the cost of all labours, materials, T&P, cleaning the surfaces of application, scaffolding etc. and removing the debris & cleaning the respective areas all complete as per specifications and as directed by EIC.

Providing and fixing of 4.0 mm thick one side decorated ACP (Aluminium Composite panel) with aluminium skin 0.50 mm thick fixed in cladding/panelling including the cost of silicone sealant, necessary cp brass/stainless screws, sundries etc.complete as per architectural drawings and directions of engineer-in-charge.

Providing and fixing anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868. Minimum anodic coating of grade AC 15) sub frame work for windows and ventilators with extruded built up standard tubular sections of approved make conforming to IS: 733 and IS: 1285, fixed with dash fastener of required dia and size (Dash fastener to be paid for separately).

Providing and fixing factory made ISI marked steel glazed doors, windows and ventilators, side /top /centre hung, with beading and all members such as F7D,F4B, K11 B and K12 B etc. complete of standard rolled steel sections, joints mitred and flash butt welded and sash bars tenoned and riveted, including providing and fixing of hinges, pivots, priming coat of approved steel primer, but excluding the cost of other fittings,glass panes complete all as per approved design, (sectional weight of only steel members shall be measured for payment). Fixing with carbon steel galvanised dash fastener of required dia and size (to be paid for separately)

Providing and fixing hard drawn steel wire fabric 75x25 mm mesh of weight not less than 7.75 Kg per sqm to steel doors/window frames etc. and priming coat with approved steel primer all complete.

Providing and fixing 1mm thick M.S. sheet to frame of MS doors by welding including all necessary fittings complete, including applying a priming coat of approved steel primer.

Providing and fixing ISI marked oxidised M.S. sliding door bolts 250x16 mm with nuts and screws etc. complete (Copper oxidised as per IS 1378)

Boring/drilling 300 mm diabore well of required dia for casing/ strainer pipe, by suitable method prescribed in IS: 2800 (part I), including collecting samples from different strata, preparing and submitting strata chart/ bore log, including hire & running charges of all equipments, tools, plants & machineries required for the job, all complete as per direction of Engineer-in-charge, upto 90 metre depth below ground level.

Supplying, assembling, lowering and fixing 150 mm nominal size dia in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge.

Supplying, assembling, lowering and fixing 150 mm nominal size dia in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge.

Gravel packing in tubewell construction in accordance with IS: 4097, including providing gravel fine/ medium/ coarse, in required grading & sizes as per actual requirement, all complete as per direction of Engineer-in-charge

Development of tube well in accordance with IS : 2800 (part I) and IS: 11189, to establish maximum rate of usable water yield without sand content (beyond permissible limit), with required capacity air compressor, running the compressor for required time till well is fully developed, measuring yield of well by "V" notch method or any other approved method, measuring static level & draw down etc. by step draw down method, collecting water samples & getting tested in approved laboratory, i/c isinfection of tubewell, all complete, including hire & labour charges of air compressor, tools & accessories etc., all as per requirement and direction of Engineer-in-charge.

Providing and fixing 150 mm dia suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of:

Providing and fixing 150 mm clamp M.S. clamp of required dia to the top of casing/housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete.

Providing and fixing 150 mm clamp Bail plug/ Bottom plug of required dia to the bottom of pipe assembly of tubewell as per IS:2800 (part I).

Supplying and fixing of PVC pipe 160 mm dia single socketed pipe of 4 Kg pressure ISI Marked , Prince / Supreme or equivalent approved make for rain water/Sewer and jointed to PVC fittings with suitable jointing PVC adhesive compound, fixed with necessary clamps at an interval of 1.20 m. approx., including cost of labours, materials, clamps for holding the pipes fixed on walls with screws, wastages, T&P etc. complete at all height as per specification, drawing and as directed by Engineer in charge For Rain water harvesting network pipe line

Supplying and fixing of PVC pipe 200 mm dia single socketed pipe of 4 Kg pressure ISI Marked , Prince / Supreme or equivalent approved make for rain water harvesting network and jointed to PVC fittings with suitable jointing PVC adhesive compound, including cost of labours, materials, clamps for holding the pipes fixed on walls with screws, wastages, T&P etc. complete at all height as per specification, drawing and as directed by Engineer in charge

Providing and fixing of following PVC Pipe fittings ISI Marked , Prince / Supreme or equivalent approved make for rain water harvesting network and jointed with PVC pipes including cost of labours, materials, clamps for holding the pipes fixed on walls with screws, wastages, T&P etc. complete at all height as per specification, drawing and as directed by Engineer in charge

PVC Tee 200x160 mm dia

PVC Reducer socket 200x160 mm dia

PVC Socket 200 mm dia

PVC elbow 200mm dia

PVC Socket 160 mm dia

PVC elbow 160 mm dia

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete with Hot finished seamless type tubes.

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel rade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineerin-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required including cost of all material and labour, T&P, scaffolding, wastages etc., all complete as per direction of EIC.

Providing and fixing precoated galvanised steel sheet roofing accessories 0.50 mm (+0.05 %) total coated thickness, Zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns using self drilling/ self tapping screws complete including cost of all material and labour, T&P, scaffolding, wastages etc., all complete as per direction of EIC. Ridges plain (500 - 600mm)

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Manufacturing, supplying and fixing Informatory road signage retro reflective overhead signage boards made up of 2 mm thick aluminium sheet, face to be fully covered with high intensity and encapsulated lens type heat activated retro reflective sheeting conforming to type - III of ASTM-D-4956-01 as approved by Engineer-in-charge, letters, borders etc. as per IRC : 67-2001 in silver white with blue colour back ground and with high intensity grade, pasted on substrate by pressure sensitive adhesive backing which shall be activated by applying pressure conforming to class II of ASTM-D-4956-01 and fixing the same to the plate of structural frame work by means of suitable sized aluminium alloys, rivets or bolts & nuts @ 300 mm centre to centre all along the periphery as well as in two vertical rows along with theft resistant measures, including the cost of painting with two or more coats of epoxy paint in grey colour on the back side of aluminium sheet including appropriate priming coat. The rate includes the cost of rounding off the corners, fixing and errecting the same in position all complete as per drawings, specifications and direction of the Engineer-In-Charge

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing 18 mm thick gang saw cut Granite stone slab of colour black, Cherry/Ruby red with Area of slab over 0.50 sqm, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing of edges to give high gloss finish etc. complete at all levels.

Providing and fixing of 500 mm long GI nozzle with Flange of following diamenter to be fixed in RCC walls of water tanks conforming to relevant including the cost of all materials, labour, curing, wastages, T&P etc., all complete at all heights as per specification and as directed by Engineer In Charge.

100 mm dia GI Nozzle with Flange

65 mm dia GI Nozzle with Flange

Supply and installation of three phase, 50 hz, vertical multistage centrifugal pump Capacity 7.50 HP for lifting of water from underground tank to to overhead tank of mid rise building, head range 28-40 meter etc all complete testing, commissioning as required and directed by EIC. Pump Makes: KSB/ Kirloskar Brothers(KBL)/Crompton/CRI pumps etc.

Supply and installation of 2.0 HP submersible pump for water tank evacuation / draining out the sum well water as and when required etc all complete including testing, commissioning etc as required and directed by EIC. Pump Makes: Kirloskar/Crompton/V-guard/Havels/CRI etc.

Supply & Installation of new feeder pillar box outdoor type double door IP67 protected, vermin and weather proof made out of 14 SWG thick CRCA sheet including canopy type roof 15 cm extended in all side and two part hinged door in front side with knobs closing the front side door gasket arrangement and back side fixed with Nut, bolts and gasket, including provision of one set of aluminium busbar 250A rating for phase and 100 A for neutral fixed on DMC/SMC insulator with RYB Black colour code with heat shrinkable PVC sleeves and holes in bus bar strip and provision of suitable cable gland for cable entry including two coat of powder quoted paint complete and installation on PCC foundation with thermostat, door limit switch and LED fitting as per following details: 1. Incoming:- MCCB 250A rating with HRC fuses Make: L&T/Siemens/Schneider with manual changeover switch of same make for provisioning of dual supply and Single Phase Preventer. 2. Outgoing: 02 nos. of 63A MCCB complete Make: L&T/Siemens/Schneider 4. Phase indicating lamps for RYB on Each incomming/outgoing 5. Digital Multifunction meter of L&T/Secure/Risabh make for measurement of Volatge/ampere/power factor/KVA/KWH/MD. 5. Suitable DOL/Star-Delta starters for 7.5 HP raw water pump with water level controller and mositure relay- 03 nos each. 6. Suitable DOL starters for 2.0 HP sump pump- 03 nos. 7. Wiring for water level control (water tank kept upto a height of 30-33 meters from the pump). Note: Drawing of feeder pillar shall be get approved before fabrication work and making of foundation for installation work is in the scope of supplier. Work is to be done as per the direction of Engineer- In-Charge.

Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface/recessed medium class PVC conduit, with modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Make of Wire: Polycab/Finolex/L&T/Havells PVC Heavy duty Conduit: AKG/GM/CAP/Anchor

Wiring for twin control light point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable in surface / recessed medium class PVC conduit, 2way modular switch, modular plate, suitable GI box and earthing the point with 1.5 sq.mm FRLS/HFFR PVC insulated copper conductor single core cable etc. as required. Make of Wire: Polycab/Finolex/L&T/Havells PVC Heavy duty Conduit: AKG/GM/CAP/Anchor

LED Flood Light 100W, powder coated pressure die cast aluminium (System lumen efficacy ≥105 <120 lm/Watt). Supplying, Installation, Testing & Commissioning of Flood Light, powder coated pressure die castaluminium body with built in or separate driver as per the requirement with Driver efficiency >85%,Input voltage: Input voltage: 140-270 Volt AC, frequency 50/60 hz, Operating temp range -5 0C to 50 0C, internal surge protection of 5 KV L,N,E as per IEC 61000-4-5, Driver efficiency >85%,THD < 10% as per IEC 61000-3-2, P. F.≥0.95, IP-66,IK-10, CRI >70, under voltage and over voltage protection, EMI-EMC as per CISPR -15, lenses for beam angle 30 deg-120deg as per the application and the project requirement., suitable tilt able fitting, life time (LED, Driver & electrical circuitry) of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life. Make of Light :- Phillips / Crompton Greeves/ Wipro/Osram/Havells

LED Batten light 4 feet (System lumen efficacy ≥120 <135 lm/Watt). (18-22W) Supply, Installation, Testing & Commissioning of LED surface mounted Batten light of following body material and construction as per IS : 10322 with driver (Replaceable) as per the requirement with Driver efficiency >85%, Operating voltage AC 140-270 Volt, frequency 50/60 hz, Operating temp range -5 °C to 40 °C, internal surge protection of 2.5 KV with Short & Open circuit protection, THD < 10%, P.F.≥0.95, IP20, CRI >80, Flicker free, (flicker should be below 5 %), life time (LED, Driver & electrical circuitry), of minimum 50000 Burning Hours with 70% of initial Lumen maintained till life ends, CCT 3000°K / 4000°K / 5700°K /6500°K (As per ANSI Bin), SDCM(Standard Deviation 45 DELHI SCHEDULE OF RATES (E&M)-2025 Colour Matching) <3, Maximum power consumption should not more than the specified rating and Fixture shall be of relevant BIS standard. Manufactures Word Mark/ Name Engraved/ Embossing/ Screen printing on housing. complete in all respect i/c external connections with 1.5 sq mm FRLS/HFFR, PVC insulated copper conductor single core cable and earthing etc. as required with Minimum 5 year OEM warranty. System lumen efficacy ≥105 <120 lm/Watt output . LM79 & LM80 Test report and all testing required for LED fixtures as per BIS shall be submitted. Shape size and CCT shall be as approved by Engineer-in-Charge as per requirement. (Thermal management: heat sink of aluminium housing such that LED junction temperature shall not rise above 90°C). Powder coated die cast /Extruded aluminium Body. Make of Light :- Phillips / Crompton Greeves/ Wipro/Osram/Havells

Wiring for circuit/ submain wiring along with earth wire with the following sizes of FRLS/HFFR PVC insulated copper conductor, single core cable in surface/ recessed medium class PVC conduit as required:- (i) 2 X 2.5 sq. mm + 1 X 2.5 sq. mm earth wire Make: Finolex/Polycab/Havells

2 X 4 sq. mm + 1 X 4 sq. mm earth wire Make: Finolex/Polycab/Havells

Supply & making One independent domestic power point with 5 pin, 6/16 Amps modular socket controlled by 16/20 Amp SP MCB modular type, with 4.0 sqmm P.V.C. insulated, copper FRLS conductor, multi stranded wire 1100/660 Volts grade in heavy duty P.V.C. pipe of including all accessories required for making power point such as P.V.C. pipe accessories, M.S. Box. The pipe shall be laid as per site requirement i.e. it may be concealed in floor/wall or flush to the wall. 2.5 sq.mm PVC insulated, single strand, copper FRLS wire shall be used in pipe with others wires for earthing of complete point wiring. Make: GM/Honeywell(MK)/Schneider Electric/Legrand (Blank plates shall be used as per site requirement)

Supply & making One (half point) with 5 pin, 6 Amps socket controlled by 6 Amps switch modular type on the same board with other switches with 1.5 sqmm, PVC. insulated,copper FRLS type conductor, multi stranded wire. Make: GM/Honeywell(MK)/Schneider Electric/Legrand (Blank plates shall be used as per site requirement)

Supply and fixing of TP&N distribution board with Double Door 6 way per phase (LDB),make: L&T/Siemens/Schneider/Legrand/Hager with supply and fixing of following MCBs C-Curve and Isolator Legrand/Havells/L&T make, making connection and testing as per direction of EIC . MCB/DISTRIBUTION BOARDS(MAKE:- L&T/Siemens/Schneider/Legrand/Hager)

Supply & installation of 400 mm wall fan with remote with air delivery atleast 67 CMM, Speed 1280 RPM Corrosion resistant powder coated Make: USHA/Crompton/Orient/Atomberg

250 mm, 1250 RPM & Air displacement 780 CMH Plastic body exhaust fan Make: USHA/Crompton/Orient/Atomberg

Supply, laying(underground), connection and testing of under noted size of aluminium conductor, XLPE insulated, PVC sheathed, steel armoured 1100 volts grade power distribution cables conforming to IS7098 part I 1988, make Havells/Grandley/Polycab/Gloster by digging earth 85+/- 5cm depth, 25 cm width and supply & laying adequate sand and new class 'II' bricks for protection of cable, filling earth, leveling etc as per standard code of practice as per direction of EIC.

Supply, laying(underground), connection and testing of under noted size of aluminium conductor, XLPE insulated, PVC sheathed, steel armoured 1100 volts grade power distribution cables conforming to IS7098 part I 1988, by digging earth 85+/- 5cm depth, 25 cm width and supply & laying adequate sand and new class 'II' bricks for protection of cable, filling earth, leveling etc as per standard code of practice as per direction of EIC. make Havells/Grandley/Polycab/Gloster

Supply & Installation of new feeder pillar box outdoor type double door IP67 protected, vermin and weather proof made out of 14 SWG thick CRCA sheet including canopy type roof 15 cm extended in all side and two part hinged door in front side with knobs closing the front side door gasket arrangement and back side fixed with Nut, bolts and gasket, including provision of one set of aluminium busbar 250A rating for phase and 100 A for neutral fixed on DMC/SMC insulator with RYB Black colour code with heat shrinkable PVC sleeves and holes in bus bar strip and provision of suitable cable gland for cable entry including two coat of powder quoted paint complete and installation on PCC foundation with following: 1. Incoming:- Switch Fuse unit 250A rating with HRC fuses Make: L&T/Siemens/Schneider with manual changeover switch of same make for provisioning of dual supply. 2. Outgoing: 09 nos. of 32A & 09 Nos. of 63A busbar mounted bakelite fuse base per pahse complete Make: L&T/Siemens/Schneider 4. Phase indicating lamps for RYB on Each incomming/outgoing 5. Digital Multifunction meter of L&T/Secure/Risabh make for measurement of Volatge/ampere/power factor/KVA/KWH/MD. Note: Drawing of feeder pillar shall be get approved before fabrication work and making of foundation for installation work is in the scope of supplier. Work is to be done as per the direction of Engineer- In-Charge.

Making End Termination of 1100 V grade XLPE insulated and PVC sheathed armoured Aluminium conductor cable of following sizes with Supply & Fixing of Lugs & Glands as per direction of EIC. (make: 3M/Raychem)

Making End Termination of 1100 V grade XLPE insulated and PVC sheathed armoured Aluminium conductor cable of following sizes with Supply & Fixing of Lugs & Glands as per direction of EIC. (make: 3M/Raychem)

Supply, installation, commissioning & testing of complete set of Maintenance Free Chemical Earthing with Copper Bonded Electrode – Diameter 17.2 mm (approx.) , Length – 03 meter (250 microns) UL listed with 25x6x150mm copper strip exothermically welded at top of the rod in T shape for connecting strip or wire with RoHS complied environmentally carbon based backfill compound (Maintenance free type)- 25 Kgx2 bag with heavy duty polyplastic cover 300x300mm Make: OBO/JeF/CAPE

Supply and laying of 6 SWG GI wire at 0.5m. below ground level for earth connection to MCB DB. The work includes bending, cutting, connecting etc. as per site requirement. The wire shall be properly supported. Complete job. Work is to be done as per the direction of engineer in charge.

Supply and laying of GI strip 25*5mm for earth pit connection to pedestal DB on surface or in recess for connections etc. as required. The work includes bending, cutting, connecting etc. as per site requirement. The wire shall be properly supported. Complete job. Work is to be done as per the direction of engineer in charge.

Supply of 7 meters, Hot Dip Galvanized OCTAGONAL continuously tapered street light pole with single arm GI bracket (length of bracket shall be based on design) for installation of LED Street light luminaire double arm with 90W Cool white LED street light, in-built junction-box complying relevant indian standards, ability to withstand maximum wind speed of 150km/hr.

Installation and commissioning (Pole erection, pole alignments, light fixture fixing, cable laying, cable termination, testing and commissioning of above mentioned 7 meters height. Work to be done as per site requirement and direction of Engineer-In-Charge.

Total (A)

Above

HAL-AD/9904/4765/CE/2026

Civil and allied electrical works for addition of amenities, infrastructure facilities and allied services including statutory and fire safety requirement for B- type multistory building at HAL Township Lucknow.

Description

Name of the Individual / Firm / Company: * Mandatory

Type of ownership Pvt. Ltd. / Proprietorship/Partnership/ Public limited/ Govt. Agencies/ Trust

Details of Constitution or Legal Status such as certificate of incorporation, shops and establishments, Contractor registration No etc.,

Address for correspondence:

Contact details

Intending parties having credentials as mentioned below may participate in e-tendering. The pre-qualification requirements for the works are as under :-

List of similar works executed in the past 7 years with value, schedule period of completion reasons for delay in completion if any and salient features of works, with documentary evidence of satisfactory completion.

PAN No.:

Constitution and legal status i.e. Proof of proprietary/Partnership firm or company & authorised person for receiving or signing the documents to be submitted.

Goods and Service Tax ID No.

SAC (Service Accounting code) along with the tax structure.

Income Tax Returns for the last three years

Annual turnover for the last five years.

Plant & Machinery details for the work.

Proposed work completion schedule in the form of bar-chart and monthwise billing plans.

Value of work on hand as on date of submission of tender duly certified by CA also indicating the stipulated period of completion (required for bid capacity also)

Bank Balance Statement for the last thee months.

Overdraft facilities available with the agencies.

Balance sheet for the last five years.

List of supervisor/ technical staff/

Bank account details such as account no., name of account holder, name and address of the bank, IFSC code duly certified by the bank along with cancelled cheque as a document of proof shall be attached.

Registered Contractor

Tenderer or its associate should posses electrical license under class ‘A’ category for execution of electrical works. The bidder shall submit the valid document i.e. license copy issued from the competent authority/ agency along with the tender document. In case, if license is expired at the time of submission of document, the bidder shall give an undertaking that renewed license will be furnished before execution of electrical works. Further the bidder will be responsible for all the contractual obligations with HAL.

Average annual financial turn over during the last 3 years, ending 31st March 2025 of the previous financial year [ should not be less than 30% of Amount put to tender]

EMD of Rs.675360.00

Latest Solvency Certificate issued from Nationalized/ scheduled Bank issued and NOT before 12 months from the last date of Tender submission

Experience of having successfully completed similar works during last 7 years ending last day of previous month. [Latest work experience certificate may be uploaded]

(i) THREE similar completed works each costing not less than the amount equal to 40% of the estimated cost.

(ii) TWO similar completed works each costing not less than the amount equal to 50% of the estimated cost.

(iii) ONE similar completed work each costing not less than the amount equal to 80% of Amount put to the tender.

Details of person holding the power of Attorney (If different from contact person)

DECLARATION I

DECLARATION II

DECLARATION III