Manufacturing, Supplying and installation of Pre Fabricated Gents and Ladies Toilet of size 10 feet x 10 feet at Laxmanpur-2 nearing parking area at Coral Point at Shaheed Dweep under CD-I, A.P.W.D., Port Blair

Amount

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m.

All kinds of soil

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :

1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size).

Centering and shuttering including strutting, propping etc. and removal of form for all heights :

Foundations, footings, bases of columns, etc. for mass concrete

Providing and fixing M.S. Tubular frames with rectangular/ L-Type and U type sections, made of 1.60 mm thick M.S. Sheet, joints mitred, welded and grinded finish, with profiles of required size, including fixing of necessary butt hinges and screws and applying a priming coat of approved steel primer.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing and fixing VIMM grade recycled weather proof fire retardant termites free scratch proof composite Boards ( Tetra packs, Plastic, aluminium) with exterior Alco panelling finish, i/c cutting of wall board for exhaust fan and ventilators etc all complete as the direction of EIC.

Providing and fixing FRB Corrugated roofing with VIMM grade recycled weather proof fire retardant termites free scratch proof composite Boards ( Tetra packs, Plastic, aluminium) i/c cutting, finishing of board etc all complete as the direction of EIC.

Providing and fixing XIMM Garde Recycled Weather proof fire retardant termites free Antiskid composite Boards 19 mm thick (Tetra Pack, Plastic, aluminium) for flooring including providing and laying of antiskid floor mat etc all complete as per the direction EIC .

Providing and fixing Entrance doors with VIMM grade recycled weather proof fire retardant termites free scratch proof composite Boards ( Tetra packs, Plastic, aluminium) with necessary fitting including hinges etc all complete as the direction of EIC.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with a wall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineer- in-Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19mm x 19mm for styles and 15x15mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture . M.S. frame covered with 5mm thick heat moulded PVC 'C' channel of size 30mm thickness, 70mm width out of which 50mm shall be flat and 20mm shall be tapered in 45degree angle on both side forming styles; and 5mm thick, 95mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115mm wide PVC sheet out of which 75mm shall be flat and 20mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10mm (5mm x 2 ) thick, 20mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail. paneling of 5mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7mm (5mm+2mm) thick x 15mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5mm thick PVC strip of 20mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge. Manufacturer’s specification & drawing.

30 mm thick plain PVC door shutters

Providing and fixing white vitreous china pedestal type water closet (European type W.C. pan) with seat and lid, 10 litre low level white P.V.C. flushing cistern, including flush pipe, with manually controlled device (handle lever), conforming to IS : 7231, with all fittings and fixtures complete, including cutting and making good the walls and floors wherever required : [Jaquar]

W.C. pan with ISI marked white solid plastic seat and lid

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge.

Providing and fixing toilet paper holder : [Jaquar]

C.P. brass

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of 430x260x350 mm or 340x410x265 mm sizes respectively. [Jaquar]

Providing and fixing PTMT urinal cock of approved quality and colour.

15 mm nominal bore, 80 mm long, 42 mm high and 30mm wide with BSP female threads weighing not less than 48 gms

Providing and fixing C.P. brass bib cock of approved quality conforming to IS:8931 : [Jaquar]

15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS:8931 [Jaquar]

15mm nominal bore

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern, including painting of fittings and brackets, cutting and making good the walls wherever require: [Jaquar]

White Vitreous China Wash basin size 550x400 mm with a pair of 15 mm C.P. brass pillar taps

Providing and fixing aluminium sliding door bolts, ISI marked anodised (anodic coating not less than grade AC 10 as per IS : 1868), transparent or dyed to required colour or shade, with nuts and screws etc. complete :

Providing and fixing aluminium tower bolts, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868 ) transparent or dyed to required colour or shade, with necessary screws etc. complete.

Providing and fixing aluminium handles, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour or shade, with necessary screws etc. complete

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door width upto 700 mm), with necessary accessories and screws etc. complete.

Providing and fixing of Exhaust fan of size 30 x 30 cm size including cutting of wall wherever required etc all complete.

Finishing with Epoxy paint (two or more coats) at all locations prepared and applied as per manufacturer's specifications including appropriate priming coat, preparation of surface, etc. complete.

On steel work

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, including fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and testing of joints complete as per direction of Engineer in Charge. INTERNAL WORK - EXPOSED ON WALL

15 mm nominal outer dia Pipes

25 mm nominal outer dia Pipes

Providing and fixing CPVC gate of approved quality including fixing with necessary solvant etc all complete :

25 mm nominal bore

Providing and fixing CPVC union with necessary srew end etc all complete :

25 mm nominal bore

Providing and fixing PVC pipes of approved quality as per the direction of EIC.

110 mm dia

75 mm dia

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank.

Circular tank

Supplying and fixing Bio Digester Tanks for septic tank use including making ready of the surface for placement of tanks etc all complete as per direction of EIC.

Providing Electrical fitting with Solar Power operated 5 WT LED Lights in each cabin and common area, Solar operated 16 nos 2 pin mobile charging point, 1.50 sq.mm copper Electric wiring with 25 Amp etc all complete as directed by EIC.

ANAND TRADERS AND CONSTRUCTION

C.M.ROY CONSTRUCTION

M/s Sagar Enterprises

R DHARMALINGAM

N.C. ENTERPRISES

PRAN GOPAL DAS

N S CONSTRUCTION