Construction of Addtional work in kitchen shed in Vadakku Karukurichi at Vadakku Karukurichi Cheranmhadevi Panchayat union

Brick work in following Cement Mortar using best quality Burnt Clay Brick of size 8 3/4" x 4 1/4" x 2 3/4" with class designation of 7.5 conforming to IS 1077-1992 for foundation and basement including Cost of Mortar Plasticizer curing, etc.,complete complying with standard specification and as directed by the departmental officers. Brickwork shall be done as per IS 2212-1991 adopting English Bond generally.other type of bond shall be done as directed by the Executive Engineer in charge. In Cement Mortar 1:5

Supplying and erecting steel centering including necessary supports for plane surfaces for Reinforced Cement Concrete works such as column footings, column pedestals, plinth beams, grade beams, staircase steps, Sill slabs etc. which require only nominal strutting using mild steel sheets of size 90cm x 60cm and 10 BG stiffened with welded mild steel angles of size 25mm x 25mm x 3 mm for boarding, laid with silver oak joists of size 10cm x 5cm & 7.5cm x 5cm as support runner, vertical stiffener, side support and Top Horizontal stiffener spaced at about 60cm to 90cm centre to centre or at suitable intervals etc. complete in all floors complying with standard specifcation. (Payment for centering shall be given after the concrete is laid)

Providing and laying in position, standardised concrete Mix M 20 Grade by insitu machine mix concrete adopting weighing batch method in accordance with IS 456 using 20mm and down graded hard broken granite stone jelly for all RCC items of works with minimum cement content of 325 kg/m3 and maximum water cement ratio of 0.55, including admixture (plasticiser / super plasticiser) in recommended proportions as per IS:9103 to accelerate, retard setting of concrete, Improve workability without impairing strength and durability with about (5 cu.m.) 7730 kg. of 20mm machine 3 10-12mm machine crushed stone jelly and with about (4.79 crushed stone jelly and with about (3.3 cu.m.) 5156 kg. of cu.m) 7670 kg. of crushed stone sand, but excluding cost of reinforcement grill and fabricating charges, centering and shuttering and also including laying, vibrating with mechanical vibrators, finishing, curing, etc. and providing fixtures like fan clamps in the RCC floor/ roof slabs wherever necessary without claiming extra, etc., complete complying with standard specification and as directed by the departmental officers. The coarse and fine aggregates to be used should comply with the requirements of IS standards. (No separate payment will be made by the Department for the excess usage of materials)

Supplying fabricating and placing in position Mild Steel/Tor Steel reinforcement grills of all variety like 0/CTD/TMTand all grade like Fe 500, Fe550D, Fe 500 D for all RCC works as per design given including cost of real reinforcement and GL binding wire, wastage etc. complete complying with standard specification and as directed by the departmental officers. (Contractor has to make his own arrangements for the supply of steel reinforcement and binding wire)

Providing granolethic floor finish in cement concrete 1:2:4 mix using 10-12mm ISS metal to 25mm thick including cost and conveyance of all materials to site and all labour charges for mixing, laying, curing etc complete for 10 cum.

Plastering with Cement Mortar 1:5 (One cement and Five Plastering sand), 12mm thick in all floors including mortar 6 plasticizer at 200ml per 50Kg of cement used, curing etc. complete complying with standard specification and as directed by the departmental officers.

Painting two coats of newly plastered wall surface with ready mixed plastic Exterior emulsion paint of first class quality and of approved colour over a priming coat including thorough 7 scrapping, clean removal of dirt, and including necessary plaster of paris putty, wherever required etc., complete complying with standard specification and as directed by the departmental officers.

Painting new iron works such as steel doors, windows, ventilators, window bars, balustrades etc., with two coats of best approved first quality and colour of synthetic enamel paint over the existing red oxide priming coat in all floors excluding cost of priming coat etc., complete complying with standard specification. (The make, quality and colour of paint should be got approved by the Executive Engineer before use on works.)

Manufacturing supplying and fixing of steel door with the following specification MS angels of size 40x40x6mm are used for the outer frames and M.S. angles of size 35x35x5mm for the shutter frames stiffeners with 32 x 6mm M.S flat is provided at required intervals in the shutter frame. 18-gauge C.R. sheet laid as panel in the shutter and welded Intact. M.S. flat 18x5mm is welded over the 32 x 6mm M.S fiat M.Sandwitching the C.R. sheet in between additional stiffeners with 18x5mm M.S. flat is provided diagonally at the 9 rear side of the shutter, 3nos. of hinges in case of single leaf and 6nos, of hinges in double leaves shutter to be provided 6nos. of holdfasts 120 mm in length made of angle section spliced at the ends are welded to the outer frames of the door. Tower bolts 2nos. one at the top and the other at the bottom are provided ino. Aldrop is provided incase of double leaf door at lock rail section in the door in single leaf door, one more aldrop is provided in the inner lock rail section of the door One rotaing locking arrangements for the inner side of the door and additional provision for locking arrangements

door (0.90x2.10m)

jolly (0.90x2.10m)

Jolly (1.50x1.20m)

Making new truss using new mateials of MS sections including cutting the angle to the required length drilling holes wherever necessary for fixing the pipe purlins, rafters Supplying and fixing of 0.47mm thick Galvalume sheet on Side Cladding with necessary framing supports with neat alignment and necessary rubber beading etc all complete as

Wiring with 2 X 1.5 Sq.mm (22 / 0.3) PVC insulated SC unsheathed Copper conducutor cable of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC

Wiring with 2 X 1.5 Sq.mm (22/0.3) PVC insulated SC 3 unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC

Wiring with 2 X 1.5 Sq.mm (22/0.3) PVC insulated SC 3 unsheathed Copper conducutor of 1100V grade in suitable PVC rigid pipe concealed in wall and ceiling with PVC

Supply and run of 2 of 4.00 sq.mm (22/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade on 7/20GI bearer wire for service connection mains SD 65

Supply and run of 2 X 4 sq.mm (56/0.30) PVC insulated SC unsheathed copper Conductor of 1100 V grade in 25 mm dia GI pipe (Class B) suitably bent at both ends with necessary angle iron upright and end supportss for mains SD70

Supply and fixing of TNEB meter board suitable for 32A single phase 5 service connection with 32A fuse unit (500V)32A neutral link and earth link (1"x1/8" copper)

Supply and fixing of WT bulk head fitting with guard (Philips / Bajaj / Crompton / K Lite) suitable for incandescent lamp with 100 W led bulb.SD 85

Supply and fixing of single box type 4'40 W flu fitting 3 complete with copper choke and condensor with conduit pipe suspension from the ceiling with PVC unsheathed copper

Supply and fixing of fancy shad and 15W LED BULB SD 80