Provn of certain Special repair, LBW, Revenue and Minor Works under AGE B/R II of GE(N) Bikaner at Mil Stn Bikaner

Amount

Excavating in trenches, n exc 1.5m wide and n exc 1.5m in depth; for foundation etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sq m on plan and n exc 1.5m in depth and getting out in soft/loose soil.

M&L RCC M-25 as in Slabs supported on walls, beams and columns in floors, roofs, landings, blaconies, canopies, deck slabs and in shelves and the like complete all as specified.

M&L RCC M-25 as in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified.

M&L RCC M-25 in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc; basement slabs, under-reamed piles and mass concrete

M&L RCC M-25 as in Columns, pillars, piers, posts and struts complete all as specified.

M&L Formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; not exceeding 200m thick (Horizontal or sloping) of rough finished sur faces of concrete flat surface complete all as specified.

M&L Formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressum-mers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc.of rough finished sur faces of concrete flat surface complete all as specified.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; verticle or to batter of rough finished sur faces of concrete flat surface complete all as specified.

M&L Formwork to sides of pillars, posts, struts, piers,columns, and stanchions of rough finished sur faces of concrete flat surface complete all as specified.

Mild steel TMT bars 10mm dia and over,cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips.

Mild steel TMT bars 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips.

Mild steel TMT bars 8 mm dia and up to 10 mm dia, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mmdia or securing with clips.

M&L Cement concrete 1:4:8 type D-2 using 40mm graded stone agregate in foundations, filling and mass-concrete

Returning, filling in, including spreading, levelling, watering and well ramming in layers not exc 25 cm in soft/loose soil.

Removing excavated material n exc. 50m and depositing where directed at a level n exc. 1.5 m above the starting point

M & L for 10 mm thick Cement plaster in CM 1:4 on Rcc Slab including water proofing compound as per manufacturer's instruction complete

Preparing surface and cleaning of concrete slab by wire brushing and applying evenly a tack coat of industrial bitumen 85/25 at the rate of 1.20 Kg per sqm including cleaning surfaces complete all as specified.

Applying a priming coat of bitumen primer @ 0.7 ltr/sqm complete all as specified.

S&F 300 micron polyethylene sheet complete all as specified.

M&L Lime concrete terracing as in roof complete all as specified and as directed by Engineer-in-Charge.NOTE:- For lime concrete, mudia kankar (source : NAL) and Kolayat coarse sand in lieu of brick aggregates and Surkhi respectively as specified in MES schedule Part-I shall be used.

M&L 40 mm thick brick tiles bedded on 10mm thick CM 1:6 and joints grouted flush in cement and sand mortar (1:3) mixed with 5% of crude oil by weight of cement complete all as specified and as directed.

M&L for Brick work with fly ash (old size) bricks built in CM(1:6) straight or curved on plan exc. 6m mean radius all as specified.

M&L for 15mm thick rendering in cement mortar 1: 6 on fair faces of brick work or concrete surfaces, finished even & smooth without using extra cement

M&L for 15mm thick Rendering in cement mortar 1: 4 on fair faces of brick work or concrete surfaces,including water proofing liquid finished even & smooth without using extra cement

M&L for 5 mm thick rendering in cement mortar 1:3 on concrete surfaces finished even & smooth without using extra cement.

M&L for 5 mm thick rendering in cement mortar 1:4 on concrete surfaces in sides of beam and coloums etc., finished even & smooth without using extra cement

M&L for preparation of new surface and applying two coat of distemper oil emulsion on one coats of primer with chalk whiting on plastered surface complete

M&L for preparing new plastered or unplastered surfaces of walls and applying two coats of cement base paint including a coat of white wash primer coat complete.

M&L for Preparing new plastered surfaces of ceiling and applying three coats of white wash complete.

M&L for PCC 1:2:4 type B-1 using 20mm graded stone aggregate as in coping, bound stone and roof covering complete all as specified.

M&L for 75mm thick Cement concrete 1:3:6 type C-2 using 40mm graded stone aggregate in plinth protection, , finished even and smooth using extra cement laid in panels, including making joints 12mm wide to the full depth of PCC at every 3 metres and at every change of direction and filling the same with & including bitumen and sand 1:3 by weight complete.

M&L for 2nd class hard wood 30mm Flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides

M&L for Preparing new or previously untreated surfaces of wood and wood based materials of any decription exceeding 10 cm in width or girth when un-connected with other painting or when painted in different tint and applying two coats of synthetic enamel paint over & including a coat of pink primer.

Suppy of Butt hinges medium weight, cold rolled mild steel 100 mm size.

S&F Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy and fixed length of bolt 300 mm

S&F Aluminium anodised barrel tower bolts of extruded section 200 mm long.

S&F Aluminium handles cast type anodised, 125 mm size complete.

S&F Steel ventilators with top hung shutter including hinges, steel peg stay complete.

S&F Framed work such as grills, gratings etc., with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; framework of water tanks and similar work conforming to Fe 410-0 or Fe 310-0

M&L for sheet glass 3mm thick ordinary quality and glazing with oil putty in square not exc.0.5sqm in each pane

M&L 100 mm thick PCC 1:4:8 type D-2 using 40mm thick greded stone aggregate as sub base in floors complete as specified.

M & L for Hardcore of gauge n exc. 63mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface complete all as specified and as directed

M&L 40 mm thick PCC 1:2:4 Type-B-1 using 20 mm thick greded stone aggregate as in flooring complete as specified.

M & L for Machine pressed precast concrete interlocking paver block coloured with glazed top of any shape and size confirming to IS 15658-2006 of 80mm thickness, M-40 Grade with grey cement complete all as specified and as directed.

M & L For sand filling under floor complete as specified and as directed including ramming and consolidation

M & L for RCC type B0 using 12.5mm thick greded stone aggregate and setting in CM 1:3 for Providing precast cement concrete louvres and jallies, 40 mm thick (measured solid), including all mouldings but excluding frame (pre cast frame shall be measured separately and paid for under seperate Item complete.

M & L for Framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging; also fastening and fixing including any type of CI Ornamental design, Iron wheels etc. work required on site complete as per direction of Engineer - In - Charge.

M & L for Preparing the new steel surfaces and applying two coats of synthetic enamel paints over a coats of pink primer complete

M & L for Precast solid RCC 1:2:4 type B-1 using 20 mm thick greded stone aggregate block for fixing of RCC Jalli on brick wall complete all as specified and as directed on site by Engineer - In - Charge.

M & L for Pre-painted galvatume aluminium zinc coating GI based corrugated steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

M & L for Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.5mm thick of any colour having tensile strength of 550 Mpa as in roof covering/cladding to wall,fixed with self tapping screws as specified.

M & L for Hand rails, half round or other stock section or core for wooden hand-rail straight portion, drilled and countersunk for balusters running bars, for doors,balusters,nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) including all necessary drilling, bolting or riveting, etc., and similar work conforming to Fe 410-0 or FE 310-0 complete as specified and as directed.

M & L for Surface dressing not exceeding 15CM deep and removing the materials obtained from the dressing complete all as specified and as directed.

M & L for Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and as directed.

Supply and Fixing Concertina coil 450mm dia 8 coils in per Running meter of length complete all as specified and as directed

M & L for Dismantling of barbed wire fencing complete of any description as specified and as directed on site by Engineer - In - Charge.

M & L for Dismantling of posts or struts (wood, steel, or RCC) any section including taking out embeded portion and making good the disturb area or ground complete all as per specification and as directed on site by Engineer - In - Charge.

M & L for Glazed ceramic tiles (300x300mm) x 7mm thick, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the surface area complete

M & L for Screed bed or bedding layer or mortar 15mm thick for laying floor finishes 15 mm thick in floor CM 1:6 including liquid water proofing as per manufacturer's instruction.

M & L for 100 mm thick PCC 1:2:4 type B-1 using 20 mm thick greded stone aggregated complete in sub base

Supply only Liquid water proofing ISI Marked Dr fixit or equilent complete as specified and as directed by Engineer - In - Charge

M & L for GI tubes medium grade 40 mm dia complete all as specified and as directed

M & L for GI tubes medium grade 25 mm dia complete all as specified and as directed

M & L for 40 mm dia Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed

M & L for 25 mm dia Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed

M & L for GI tubes medium grade 20 mm dia complete all as specified and as directed

M & L for GI tubes medium grade 15 mm dia complete all as specified and as directed

M & L for 20 mm dia Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed

M & L for 15 mm dia Stop valves, cast copper alloy screwed down high presure, with crutch of butterfly handle, screwed both ends for iron pipe or for unions and fixed

S&F Rotational moulded polythene water storage tank cylindrical vertical with closed top hoisted and fixed in position of 1000 ltrs capacity complete

S&F Ball valves 20mm bore high pressure of PTMT with epoxy coated alum rod and high density plastic ball screwed for iron pipe and fixed

M & L for Excavation Over areas nexc 1.5M deep and getting out loose and soft soil complete as directed by Engineer - In - Charge.

M&L 100 mm thick PCC 1:2:4 Type-B-1 using 20 mm thick greded stone aggregate as in flooring complete as specified.

M & L for GI tubes medium grade 50 mm dia complete all as specified and as directed

M & L for 50 mm dia Stainless Steel pipe for Railing including cutting, notching and welding complete as specified and as directed by Engineer - In - Charge on Site

Chequered cement concrete coloured tiles having rubber hard top finish with polymer admixtures in any pattern or design of min. size 30 cm x 30 cm x 25 mm thick set jointed and pointed in neat cement slurry in floor incl 15mm thick screed bed in cement mortar 1:4, all as specified and directed.

M & L for PCC 1:3:6 using 40 mm thick grded stone aggregate in fdn filling and mass concrete complete

M&L concrete bed to drain pipe in PCC 1:4:8 type D2 using 40mm graded stone aggregate incl packing under and hunching against sides of pipe after they are laid on slope and tested for 150mm dia bore sewer pipe line ( earth work excavation and sewer pipe line will be measured and paid separately)

Supplying and laying salt glazed stoneware pipe confirming to IS 651-1972 in tranches and jointed in cement mortar 1:1 complete all as shown on drawings for 150mm internal dia of pipe ( excavation and earth work measured separately)

M&L PCC 1:2:4 type B1 using 20mm graded stone aggregate as in kerbs, benching, hunching, corbelling and drain / manholes channels etc finished even and smooth using extra cement including necessary form work

Extra for forming fair finished drain or channel 30cm inner girth in cement concrete, using extra cement, including moulds, forms, mitered/stopped ends complete all as specified ( Inner girth will be measured & paid)

M&L Sand stone slabs in sunshades, chajjas, shelves, cills, landings, cover stones, templates, etc, n exc. 2m in length, punched dressed on face and along exposed edges, self faced on other side and set and pointed in lime mortar 1:2 or cement mortar 1:4, complete

Cutting into existing manholes for connecting new drains, making good to pipe and rendering, cutting out existing benching for and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished, and reforming benching as required (Internal dia of pipe 150mm).

Provision of soak well excavation in ordinary soil foundation in PCC 1:3:6, wells of honey comded brick in CM, filled with brick bats comp. of size 4.5m depth 3.30m dia at top and appx 2.40m dia at bottom including necessary BB work conc. in fdn. stone patti roof dlab, beam 02 nos and 50mm thick PCC over stone patti roof slab and all as per Drg BTD 265 hs 1/1.

Pre cast reinforced cement concrete 1: 2 :4 using 20 mm graded stone aggregates as in manhole covers including removing old damaged cover from manhole complete all as specified and as directed by Engineer-in-Charge

S & F for Anodised aluminium snap grid frame work for false ceiling all as specified

S & f for 18/19 mm thick Perforated particle board/tiles for insulation and acoustic purposes, 60x60 cm in size, fixed with nails to timber frame work or with staples on snap grid

M & L for Vitrified Ceramic tiles 10mm thick Light Shade (square/rectangular) polished, area of each tiles not exceeding 0.36 sqm, in floors etc, set and jointed in neat cement slurry and pointed in white or coloured cement to match.

Dismantling Existing false ceiling of any type including making good the surface after removing the false ceiling battens and scantling complete in CM 1:4.

S&F PVC( SWR) pipe of 110mm bore fixed to wall or laid in trenches complete as specified and as directed.

S&F PVC( SWR) pipe of 75mm bore laid in floors or trenches.

S&F PVC(SWR) bend any radius of 75mm bore jointed with solvent cement

S&F PVC(SWR) junction double (Single tee) of size 75mm bore jointing with solvent cement.

S&F PVC(SWR) floor trap plain with grating including jointing with solvent cement of size 75mm outlet.

M&L 40mm thick Damp proof course to horizontal or vertical surface incl necessary formwork with PCC 1:2:4 type B-0 & mixing of water proofing compound as per manufacturer's instructions

M&L Glazed ceramic colour tiles of size 300x200x7mm thick as in dado/ skirting jointed in neat cement slurry and pointed with white cement mixed with pigments matching to tiles colour including 10mm thick screeding/ bed plaster in CM 1:4 complete all as specified and directed.

M&L roughly squared stone lintels, beams, hammer dressed on face and soffits, hoisted, set and pointed in CM 1:4 complete n exc 3m in length.

M & L for Jodhpur stone roof slab self faced 7.5 CM to 10 CM thick 25 Cm to 35 CM wide hoisted and set jointed and grouted in CM 1:3 complete

S&F Solid PVC door frame of size 50mmx47mm made out of 5mm plain colour PVC sheet reinforced with MS square tube all as specified and approved.

S&F factory made solid panel PVC door shutter with MS square tube 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails MS frame shall be covered with heat moulded plain colour PVC sheet stirip of 20mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top,lock and bottom rail on either side & as gap insert for top rail & bottom rail .panelling of plain colour PVC sheet to be fitted in the MS frame welded /sealed to the stiles and rails with suitable PVC sheet beading and joined together with solvent cement S&F in the steel frame at site as per specification.

S&F Vitreous china EWC(Pedestal pattern), white,(excluding flushing cistern and flush pipe), with CI ‘P’ trap of long arm of suitable size including connection to flush pipe, anti symphonic pipes, including seat cover of white colour complete.

S&F wash hand basin vitreous china size 550x400mm white flat back including CP pillar tap heavy duty as approved by GE ,waste,chain plug,pvc connection, pvc waste pipe comp all as specified

S&F for Vitreous China Urinal, Half stall type, white (excluding flushing cistern, flush pipe and waste pipe) complete including providing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe,grating and union for discharge pipe and all fitting.

S&F PVC low level flushing cistern.valve .less, syphonic action type 10 liters capacity with inlet, ball valve, float and handle with including brackets and PVC bend pipe 90cm long etc. supplied and fixed.

S & F CP Jet spray for EWC complete fixed in as specified and as directed

S&F Bib taps cast copper alloy fancy type with crutch or butterfly handle screwed for iron pipe of 15mm bore and fixed

S&F Towel rail 450 mm long of PTMT fixed with and including Chromium plated brass screws and wooden/plastic cleats.

S&F Pillar tap cast copper alloy fancy type screwed for iron pipe on both ends of 15mm bore and fixed.

S&F Stop cock cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 20mm bore and fixed.

S&F Stop cock cast copper alloy with crutch or butterfly handle screwed for iron pipe on both ends of 15mm bore and fixed.

S&F PVC connections 15mm size with PTMT nuts of length 450mm.

S&F Vitreous China wash down water closet pan coloured or white with PVC flushing cistern including fixing , traps and connecting pipe with seat cover etc complete. fixed in repairs..

Dismantling existing terrazo tiles in dado and floor or tiles in WC, Bath Room and Kitchen Etc complete

Demolition of lime concrete of any description over roof slab complete all as specified and as directed by Engineer-in-Charge..

Demolition of Brick work built in cement mortar including all quions arches pillars etc but excluding ashlar facing dressed stone work and precast concrete articals complete all as specified and as directed

Demolition of reinforced cement concrete of any description and in any position not otherwise specifically provided for (reinforcement cut as required to facilitate demolition) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings n exc 15 cm thickness (below or above ground level) complete all as specified and as directed.

M & L for form work to edges of conc flat floor and roofs nexc 200mm wide to rough finish of surface of cincrete

Dismantling Water Tank of cap exc 250 Ltr and not exc 500 Lte complete

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each complete.

Taking down shutters of any description exceeding 1 Sqm but not exceeding 2 Sqm each and refixing the same door in same opening after easening etc. complete.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) not exceeding 1.5 Sqm including making good of all surface area with cement plaster or PCC 1:2:4 to obtain the new Chowkhats excluding filling of the holdfast each complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frames) exceeding 1.5 Sqm but not exceeding 4 Sqm including making good of all surface area with cement plaster or PCC 1:2:4 to obtain the new Chowkhats excluding filling of the holdfast each complete all as specified and as directed.

Taking down cement plaster/terrazo finish on brick or stone walll etc including raking out joints, hacking for key, scrubbing down with water etc. complete all as specified and as directed.

Material and Labours for Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors on 15mm thick screeding in CM 1:6. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

Material and Labours for Non skid Ceramic tiles 7 to 8 mm thick (square /rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in skirting / dado on 10mm thick rendering on vertical surfaces in CM 1:4. set and jointed in neat cement slurry and pointed in white or coloured cement to match complete.

Supply and Fixing for Steel window with side hung shutter incl.box type hinges with steel handle of MS flat 25x5mm and 2nos tower bolt of 100mm long fixed to shutter comp. With glazing bar dovtailed or welded including one shop coat of primer.

Supply and Fixing for Steel window with side hung shutter incl.box type hinges with steel handle of MS flat 25x5mm and 2nos tower bolt of 100mm long fixed to shutter comp. Without glazing bar dovtailed or welded including one shop coat of primer.

Supply and Fixing for 1.25 mm thick Pressed steel frames of size 105mm x 60mm for single doors including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

Supply and Fixing for 1.25 mm thick Pressed steel frames of size 125mm x 60mm for double doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc complete all as per IS provns.

Material and Labours for for PCC 1:3:6 type C1 using 12.5 mm graded stone aggregate for embedding the hold fast, filling in Chowkhats, copping etc complete all as specified & directed.

Supply and Fixing for 35mm thick Second class hardwood plain, framed, panelled shutter (any Nos of panels) with panels of timber flat on both faces, feather edged or of veneered particle board medium density, wood partical board with commercial face, veneered supplied and fixed to chawkets complete.

Supply and Fixing for Second class hardwood glazed and skeleton door shutters 35mm thick, open rebated and prepared to receive glass, gauze, etc (with rebated sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc complete.

M & L for 20mm thick Partical boards medium density flat pressed single layer typeor three layer type with BWR type adhesive fixed with screws to frame work as in shelves etc.

S&F Butt hinges extruded alumonium alloy with galvanised mild steel hinges pin anodisedand fixed ,type B-21 of 100mm.

S&F mild steel pressed handles oval type stove enamelled black of 150mm

S&F hasp and staple aluminium anodised incl.bolt to hinge plate and fixed with screws of 100mm size safety type.

S&F 300mm, mild steel ordinary rat tail rod pattern springs including roller and roller plate complete all as specified and directed by Engineer-in-charge.

M and L for Galvanised wire cloth 0.56mm nominal dia of wire and avg.width of aperture 1.18mm fixed with tinned tacks or galvanised wire staples.

Hacking out old broken glass (any thickness size quality or desc.)from wooden frames or stone conc. or brick surroundsglazed with putty or fixed with beads exc.105sqm

Prerparing old decorated surfaces plastered/unplastered by brooming down etc and applying one coat of white wash on ceiling complete all as specified.

Complete removal of existing treatment of walls and applying two coats of oil bound distemper over a coat of chalk whiting complete all as specified and as directed by Engineer-in-Charge.

Complete removal of existing treatment of walls and applying two coat of cement base paint (Ist quality) in plain pattern on walls and over a coat of chalk whiting complete all as specified.

Preparing old steel surface and applying two coats of synthetic enamel paints on surfaces

Preparing old wooden surfaces and applying two coats of synthetic enamel paints on surfaces

Taking up or down steel water tubing 15mm dia and connection ,incl cleaning for refixing

Taking up or down steel water tubing 20mm dia and connection ,incl cleaning for refixing

Angle valves, cast copper alloy, chromium plated, fancy type with long shank and cup, screwed down high pressure, screwed both ends for 15 mm bore dia iron pipe or for union, ISI marked, supplied and fixed in repairs complete all as specified and as directed by Engineer-in-Charge.

Dismantling of pipes of any dia fixed to wall or laid in floor complete

S & F CP shower rose with swivel joints 75 mm size

S&F PVC(SWR) bend any radius of 110mm bore jointed with solvent cement

S&F PVC(SWR) junction double (Single tee) of size 110mm bore jointing with solvent cement.

S&F curtain rods, 25 mm dia staintless steel, including with stailess Steel brackets, stops etc and fixed in repairs.

Removing building materals etc. to a distance of 100m to 1 km , beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and as directed by Engineer-in-Charge.

20-25 mm thick single piece machine cut kota stone slab as in risers, treads of steps/landing, laid and jointed with grey cement slurry mixed with pigment to match with the shade of the slab including rubbing and polishing and also including rounding off front edges of treads and landings and also including laying over and including 15mm thick backing coat in cement and sand mortar 1:6 complete all as specified and as directed by Engineer-in-Charge.

Point wiring with stranded copper conductor cable, 1100 volts grade (ISI marked) PVC insulated and unsheathed of size 1.5 Sq mm single core in and including new non-metallic rigid PVC concealed conduit, not less than 20 mm dia, medium duty ISI marked, including conduit fittings such as tees, bends etc terminating in and including new sunken box covered with and including 3 mm thick bakelite laminated sheet top cover of approved make for one fan or light or exhaust fan or bell/buzzer point controlled by one switch including provision of 1.5 Sqmm PVC insulated unsheathed copper conductor cable, multi stranded as earth wire to common earth & connecting to earth dolly complete all as specified and directed by Engineer-in-Charge.

All as per item No 157 here-in-before but socket point on the same board with other switches complete as specifed as directed by Engineer - In - Charge

All as per item No 157 here-in-before but one light point controlled by two 02 - way switch complete all as specified and as directed by Engineer-in-Charge.

All as per item No 157 here-in-before but socket point on the independent board with other switches complete as specifed as directed by Engineer - In - Charge

S&F Switch piano flush type, Single pole 5 Amps, two way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/Cona/Havells

S&F Switch piano flush type, Single pole 5 Amps, one way ISI marked, complete all as specified and as directed by Engineer-in-Charge Make : Anchor/Cona/Havells

S&F Ceiling rose PVC/poly carbonate insulated body three terminal ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : Make : Anchor/Cona/Havells

S&F Socket outlet flush type, 3 pin, 5 Amps, ISI marked, complete all as specified and as directed by Engineer-in-Charge. Make : - Anchor/Cona/Havells

S&F Lamp holder insulated body with back plate for conduit/casing capping fittings complete all as specified and as directed by Engineer-in-Charge. Make :- Anchor/Cona/Havells

S&F Decorative ultra slim linear LED lightening fixture, energy efficent 18/20 Watt complete all as specified and directed by engineer-in-charge.Make SYSKA/BAJAJ/PHILIPS

S&F MCB single pole, 240 volts of rating 6-32 Amps, breaking capacity of 10 KA complete all as specified and as directed by Engineer-in-Charge Make :- Schneider/ HPL/Legrand/ GE/ Seimens/L&T/Indo sian/C&S/Havells/BCH/ABB

Supply and Fixing in replacement MCB suitable for 6 to 32 Amps, 240 Volt AC supply C Curve single pole and neutral(SPN) with over load and short circuit protection having rupturing capacity not less than 10 KA complete all as specified and as directed by Engineer-in-Charge. Make :- Legrand cat Part No 408590 to 408595, cat No A9NIP(6 to 32Amps C curve) in make Schnedier or equivalent in make GE, English Elect, L&T Exora series

S&F sheet metal enclosure DB 4 way, SPN single door with 200 rated bus bar complete all as specified and directed by Engineer in charge.

Taking down carefully existing unserviceable Copper/aluminum batten/surface conduit/concealed conduit point wiring (light, fan, bell/buzzer, socket or power) complete including removal of unserviceable fittings such as switches, switch-sockets, ceiling roses, pendents, sockets, lamp holders, shades, fan regulators, light fittings, bells etc (including old MS sunken boxes) and removing the retrieved materials from dismantling including making good the disturbed surface of walls, floors, ceilings etc to match with the adjoining work complete all as specified and as directed by the Engr-in-Charge.

Taking down of unserviceable DBs/switch fuses/changeover in sheet steel enclosure complete with MCBs/Fuse/grips any capacity and removing from site and making good disturbed surface of wall, floor etc. Taking after disconnecting all cable complete all as specified and as directed by the Engr-in-Charge.

S&F Ceiling fan regulator electronic type, 230 Volt, 150 Watt with 5 step of control including making holes in laminated bakelite sheet cover and connection complete all as specified and as directed by Engineer-in-Charge. Make Anchor/Cona/Havells

S&F Sheet metal enclosure for distribution boards, suitable for fixing MCBs 240 volts with 200 Amps rated bus bar, SPN, 8 ways double door , supplied and fixed in repair, including making good the disturbed surface of wall, complete all as specified and as directed by Engineer-in-Charge. Make - Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/Strandard/BCH/HPL

Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 6 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 6 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

Taking down old sub main wiring and providing new sub main wiring with 2 single core, multi-stranded PVC insulated cable unsheathed 1100 volts grade with copper conductor of size 4 sq mm drawn in and including PVC concealed including earth continuity conductor cable of size 4 sq mm PVC insulated unsheathed copper conductor cable connected to common earth and earth dolly complete all as specified and as directed by Engineer-in-Charge.

S&F Bulk head luminaries LED 10 W complete all as specified and as directed by Engineer-in-Charge Make Philips/Bajaj/Surya/CG/SYSKA

S&F in replacement Sheet metal enclosure for distribution boards flushed in wall Double door suitable for fixing MCBs 415 volts with 200 Amps rated bus bar, load line DB's are fittied with bus bar nutural links blank plates TPN vertical load line 4 ways suitable for TP/FP 'A' frame MCCB,includeing 100 Amps MCCB -01Nos ,MCB SPN 32 -04 Nos and MCB SP - 04Nos , complete all as specified and as directed by Engineer-in-Charge. Make - Havells or equivelent Legrand/ GE/Seimens/L&T/Schneider/Indo Asian/C & S/ABB/BCH/HPL Note : cost of cutting/chasing of wall and making good disturbed surface deemed to be included in the rate

Earthing complete with galvanised steel earth plate electrode 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below normal ground level surrounded from all sides by 15 cm thick packed layer of charcoal dust and common salt filling in alternate layers and electrode connections by mean of GI wire 4 mm dia by means of bolts, nuts check nuts and washers of GI or steel and connecting to earthing test point, main switch board, testing on completion including GI pipe 20 mm dia light grade for watering and bringing the same upto 30 cm above normal ground level with plug at top including pipe fittings etc complete and GI pipe 15 mm dia light grade for the protection of GI wire from earth pit to earth point complete including necessary excavation and earth work in any type of soil, returning, filling in approved soil and disposal of surplus soil to a distance n.exc 50 m all as specified as shown in electrical plate No 3 SSR Part-I.

S&F in replacement Plug and socket in sheet metal inclosure with 2 pin and earth plug and socket complete with and including MCB, SP, 20 Amps, 240 Volts heavy duty all as specified and as directed by Engineer-in -Charge.

Taking down fan, sealing cable end, dismantling blades and removing fan and blades to store complete all as specified and directed by Engineer-in-Charge.

Hanging only ceiling fan as taking down vide item si no. 23 and connecting up including provision of cable from ceiling rose or connector to fan complete all as specified and directed by Engineer-in-Charge.

Supply and laying in replacement cable XLPE insulated screened PVC bedded, galvanized steel strip or wire armoured, electric power cables (heavy duty) 1100 Volts grade with stranded aluminium conductor of size 10.00 sq mm 3 core

Excavation in trenches in soft/loose soil not exceeding 1.5 meter wide and not exceeding 1.5 mtr in depth for route of cable and getting out complete all as specified and as directed by the Engr-in-charge.

Returning, filling in soft/loose soil including spreading, leveling watering and well ramming, in layers not exc 25 cm complete all as specified and as directed by the Engr-in-charge.

Removing of surplus soil to a distance not exc. 50 mtr and depositing where directed at a level not exc. 1.5 mtr above the starting point complete all as specified and directed by Engr-in-charge.

Protection to cable with one layer of bricks laid flat butting to each other in such a way that the length of the bricks is at right angle to the central axis of the cable using old size sub-class 'B' bricks complete all as specified and directed by Engr-in-charge.

Local tibba dry sand cushioning for protection of cable complete all as specified and as directed by Engineer-in-charge. Note Local approved tibba dry sand after removal of vegetations, grass and other deleterious substances shall be used for sand cushioning.

M & L GI tubing light grade for protection of cables with pole/ in ground of size 40mm dia complete all as specified and as directed by Engineer-in-Charge.

GS BUILDERS AND ENGINEERS

N.K. CONSTRUCTION COMPANY

M/S ASHRAFI CONSTRUCTION CO

CHANDRAENTERPRISES