PROVN OF TOILET BLOCK FOR BLDG NO T 63 T 12 AND SPECIAL REPAIR TO BLDG NO P7 UNDER GE NARANGI

Amount

M&L Excavating over areas exceeding 1.5 metre deep and getting out in soft/loose soil complete all as specified and directed.

M&L surface excavation not exceeding 30 cm deep and averaging 15cm deep and getting out in soft/loose soil complete all as specified and directed.

Excavation in trenches n.exc 1.5m wide and not exceeding 1.5 m in depth for foundation etc, or for shafts, wells, cess pits, manholes, pier holes, etc. not exceeding 10 Sqm on plan and not exceeding 1.5 m in depth and getting out in soft / loose soil etc complete all as specified and as directed.

Returning, filling including spreading, levelling, watering and well ramming in layers not exceeding 25 cm each in soft / loose soil etc complete all as specified and as directed.

Removing of surplus excavated material not exc 50m and depositing where directed at a level n. exc 1.5 m above the starting point etc complete all as specified and as directed.

M&L for hardcore of broken stone or boulders of gauge n exc. 63 mm, deposited, spread and levelled in layers n exc. 15 cm thick, watered and rammed to a true surface etc complete all as specified and as directed.

M&L for sand filling under floors or in foundation , laid in layers not exceeding 15cm thick spread, levelled and rammed including watering complete all as specified and as directed.

M&L PCC (1:4:8) type D-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L PCC (1:3:6) type C-2 (using 40 mm graded stone aggregate) in foundation filliing and mass concrete complete all as specified and as directed.

M&L for PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in fixing of hold fast or bed block complete all as specified and directed.

M & L Precast RCC 1:2:4 Type B-1 ( Using 20mm graded stone aggregate) as in landings, cover slabs ( for manhole etc) chullah hoods, chajjas , water toughs, mangers, shelves and similar articles with plain faces complete all as specified and directed.

M&L for RCC 1:1½:3 type A1 (20mm graded stone aggregate) nominal mix as in Foundations, including rafts, footings, foundation beams, plinth beams, bases for columns, etc, basement slabs, under-reamed piles and mass concrete etc complete all as directed.

M&L for RCC 1:1½:3 type A1 (20mm graded stone aggregate) nominal mix as in Columns, pillars, piers, posts and struts etc.complete all as specified as directed.

M&L for RCC 1:1½:3 type A1 (20mm graded stone aggregate) nominal mix as in Slabs supported on walls beams and columns in floors,roofs,landings, balconies,canopies,deck slabs and in shelves and the like etc complete all as specified as directed.

M&L for RCC 1:1½:3 type A1(20mm graded stone aggregate) nominal mix as in beams, seimic bands, cantilevers, bressumers and lintels complete all as specified as directed.

M&L Formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified as directed.

M&L Formwork to sides of pillars, posts, struts, piers, columns, and stanchions complete all as specified as directed.

M&LFormwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work; n. exc 200m thick (Horizontal or sloping) complete all as specified as directed.

M&L formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified as directed.

Use and waste for Formwork to edges of concrete flats, treads, breaks in floors,window cills, concrete railings, openings in concrete walls, floor and roofs not exceeding 20cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar works exceeding 10cm but not exceeding 20cm wide complete all as specified and directed.

M&L for water proofing treatment to RCC roof slab, including parapet comprising with the following of treatment/specification from bottom to top:- (i) Screed bed or bedding layer of mortar 15 mm thick in CM 1:4 with mixing of WPC and surface finished fair and smooth without using extra cement after applying a coat of cement slurry @ 3 kg/sqm for laying APP membrane. (ii) Cleaning of plastered roof surface and applying one coat of cold bituminous primer @ 0.25ltr /Sqm conforming to IS:3384-1986. (iii) APP based polymeric membrane 3mm thick (minimum), weighing 3.5 Kg/sqm reinforced with polyester non woven fabric (weighing not less than 150 gms/Sqm) shall be applied over bituminous primer as specified above over by torch application. The overlaps shall be minimum 100mm on the transverse direction and 75mm on longitudinal direction. (iv) Applying two coat of aluminium paint over the APP modified membrane @ 0.11Kg/sqm.

Demolition of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stonework and precast concrete articles

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:4 etc complete all as specified as directed.

M&L for brick work with old size sub class 'B' bricks straight or curved on plan exc. 6m mean radius and built in CM 1:6 etc complete all as specified as directed.

M&L for brickwork with subclass ‘B’ old sized bricks, straight or curved on plan to any radius in half brick thick walls and built in CM 1:4 etc complete all as specified as directed.

M&L for40mm thick damp prooof course 1:2:4 type B-0 and applying evenly a tack coat of blown bitumen 85/25 @ 1.20kg per sqm including laying 150 micron thick polythelene film complete all as specified as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including builders hardware complete all as specified and as directed.

Taking down chowkats or frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm each including builders hardware complete all as specified and as directed.

Providing and fixing powder coated aluminium ( minimum thicknesss of powder coating 50 micron) work for doors, windows, ventilators and partitions ( fixed portions0 with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make confirming to IS-733 and IS- 1285, fixed with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e at top, bottom and sides with required EPDM complete all as specified and directed.

S&F steel ventilators with top hung shutters including hinges , steel peg stay complete all as specified & as directed .

S&F 35mm thick second class hard wood glazed and skeleton shutters, open rebated and prepared to receive glass, gauge etc (with out sash bar), edges of framing with plain, chamfered or rounded, fitted with cut and mitred beads for securing glass etc, sizes of members of shutters all as specified in SSR part-I section 8 clause 8.24 (a) complete all as specified and directed.

M&L for 1.25mm thick factory made pressed steel frames of size 105x60mm with single rebates including necessary fixing lugs, hinges, lock strike plate, etc complete including PCC 1:3:6 type C-0 as in back filling of window/door frame all as specified and directed.

S&F 35 mm thick flush shutter, solid core construction with particle board core and plywood face panel, commercial type on both side complete all as specified and directed.

S&F Steel window and ventilator fixed type, complete with glazing bars, dovetailed or welded etc complete all as specified and as directed.

S&F 30 mm thick Factory Made Solid Panel PVC Door Shutter consisting of frame made out of M.S. tubes of 19mm x 19mm for stiles, & 15mm x 15mm for top & bottom rails. M.S. frame shall be covered with heat moulded plain colour PVC sheet 5mm thick ‘C’ channel having a 5mm thick PVC sheet strip of 20mm width stuck inside with solvent cement, forming stiles, and plain colour PVC sheets for top rail, lock rail & bottom rail on either side, and as gap insert for top rail & bottom rail. Panelling of plain colour PVC sheet to be fitted in the M.S. frame welded / sealed to the stiles & rails with PVC sheet beading, and joined together with solvent cement adhesive etc. complete as per direction of Engineer-in-charge, manufacturer’s instructions and drawing. The width of stiles & rails will be in proportion to the width of the door shutter as per SSR Clause No 8B.2.1

M&L for Solid PVC Door Frame of size 50mm x 47mm made out of 5mm plain colour PVC sheet reinforced with M.S Square tube, supplying & fixing in opening as per specification & drawing etc complete all as directed.

M&L Cutting holes in brick walls built in cement mortar exceeding half brick but not exceeding one brick for inserting oldfast and making good dismantled portions in CM 1:3 or cement concrete 1:2:4 type B-1 complete all as directed.

S & F 100 mm size stainless steel butt hinges, complete all as specified and as directed.

S&F 150 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 200 mm size aluminum anodised, barrel tower bolts of extruded section etc complete all as directed.

S&F 125mm size extruded aluminium handles, cast type, anodised complete all as specified and directed.

S&F 150mm size extruded aluminium handles, cast type, anodised complete all as specified and directed.

S&F soccond class hard wood small fittings such as brackets of any type latch and hinges blocks , shaped door and window stops and the like including all necessary labours, articles not exceeding 200 cucm each complete all as specified and directed.

S&F floor door stopper of aluminium alloy body and tounge, anodised with hard drawn steel spring of overall length of cover plate 140mm fixed in floor complete all as specified & directed.

S&F in repair steel helical door spring 300mm ordinary rat tail rod pattern springs including roller plate complete all as specified and as directed.

S&F aluminum alloy anodised, sliding door bolts with hasp and staple, (bolt type) and fixing clips of sheets, cast or extruded section and fixing bolt and sliding bolts of extruded section or cast aluminium alloy and fixed 300mm long etc complete all as specified and directed.

S&F stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples etc complete all as directed.

Dismantling of asbestos cement (corrugated,semi corrugated, etc.) sheets in roof coverings including ridge complete all as specified & as directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated trapezoidal profile steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws complete all as specified and directed.

M&L Pre- painted hot dip aluminium Zinc alloy metalic coated plain steel sheet 0.50mm thick ( Total coated thickness), any pattern corresponding to IS 15965 : 2012 of durability class 3, atmospheric classification category 3, coating class AZ 150 of an approved colour having yield strength of 550 Mpa as in roof covering/wall cladding, fixed with self tapping screws as specified complete all as specified and directed. Note: To be executed for provision of ridges and hips.

S&F in repairs, suspended false ceiling using E-grid 2430, 180 GSM (exposed ceiling suspension system ) of grid size 600mmx600 mm with main runner 38 mm x 24 mm and wall angle 24mm x 24mm using 4mm thick High Pressure stean Crude Everest Non Asbestos Fiber Cement designer Board (E-Board Classic) in & including a grid of GI system duly suspended with 4mm dia GI wire hanger fixed with steel dash fasteners or iron purlin from the roof with adjustment clip providing positions for light fixtures,air conditioning diffuser and ducts ,sprinkler ,smoke detectors etc.The main runners to be secured to structural soffits by hanger @ 1220 mm maximum c/c. the last hanger at the end of each main runner should not be placed at more than 450mm from the adjucent wall,Flush fitting 1220 mm cross tee to be interlocked between main runners @ 610mm c/c,so as to form 600mm x 600 mm grid complete all as specified and as directed.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified and as directed.

M&L TMT steel bars 10mm dia and over, cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L TMT steel bars 8mm dia and over upto and including 10mm dia , cut to length, bent to shape required, incl cranking, bending spirally for hooping for columns, hooking ends and binding with the including mild steel wire (annealed) not less than 0.9mm dia or securing with clips

M&L for mild steel TMT bars 5 mm dia and over upto and including 10mm dia cut to length, bent to shape required including cutting, cranking, hooking ends and binding with mild steel wire (annealed) not less than 0.90mm dia as in stirrups, spacers and binders complete all as specified and as directed.

M & L for rolled mild steel work main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates confirming to Fe-410 W ( Gde-E-250 ) quality B complete all as specified and as directed.

S&F rolled mild steel plates ( plain or chequrred) channels, square cut or notched ( ordinary or counter sunk) forming holes, without any attachment confirming to Fe-410-W (Gde-E-250) quality B complete all as specified & as directed.

Demolition of reinforced cement concrete (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for all as specified and as directed.

Demolition of plain cement concrete (Un-reinforced) in ground floors and paving n exc 15cm thickness (below or above ground level) including removal of spoils/ demolished materials not exceeding 50m and depositing complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 typeD-2 (using 40mm graded stone aggregate) as in subase complete all as directed.

M&L for 75 mm thick, PCC 1:3:6, type C2 (using 40 mm graded stone aggregate) as in plinth protection, etc finished the surface even and smooth without using extra cement including provision of joint of size 10 mm wide and 30 mm deep at every 2.4 mtrs interval filled with bitumastic compound etc complete all as specified and as direted.

Dismantling floor, hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

M & L for coloured Non skid ceramic tiles 7 to 8 mm thick (Square/rectangular) area of each tile exc 0.06 sqm but n.exc 0.11 sqm, laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm laid in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M&L for 10mm thick Vitrified tiles light shade area of each tile n exc 0.36sqm as in vertical surfaces such as skirting/dados etc etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tile over and including 15mm thick screed bed in cement mortar 1:4 complete all as specified and as directed.

M & L for glazed ceramic coloured tiles 375x250x7mm/300x200x7mm /450X300X7mm thick, set and jointed in neat cement slurry and pointed in coloured cement as in vertical surfaces such as skirting, dados and risers to steps etc over and including 10 mm thick rendering in cement mortar (1:4) complete all as specified and as directed.

Demolition of stone slab and tiles of any description or thickness in floor, apron etc laid, bedded and pointed in cement mortar complete all as specified and as directed.

M&L for 18-20mm thick Kota stone slab flooring laid over cement screed base 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 20-25mm thick-20mm thick cudappah stone slab flooring laid over cement screed base 20mm thick in CM 1:6 laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete all as specified and directed.

M&L for 18 to 20 mm thick granite (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platform and the like including pointing in white cement 1:2 using granite dust with admixture of pigment to match with the shade of granite work including rounding of exposed edges of granite over and including 15mm thick backing coat in cement mortar 1:4 complete all as specified and as directed.

M&L for 18 to 20mm thick marble ( table rubbed and polished) machine cut ,as in floor laid over cement screed of 20mm thick in CM 1:6 including pointing in white cement 1:2 using marble dust with admixtures of pigments match the shade of marble including rubbing and polishing complete all as specified and as directed.

M & L in repair pre-polished cement concrete chequered tiles area of each tiles exc 0.06 Sqm but n exc 0.11 Sqm and 25 mm thick with white cement and pigments of approved make jointed with cement slurry and pointed with white cement mixed with pigment to match with the tiles over and including screed bed of 20 mm thick in cement mortar (1:6) complete all as specified and directed.

M&L Machine pressed precast concrete interlocking paver block with grey cement and pigment any shape and size confirming to IS 15658-2006 of 60mm thickness, M-35 grade including 30mm thick sand cushioning and filling joints with sand complete all as specified & as directed.

M&L in repair Machine pressed precast coloured glossy finished rubber moulded of approved design and pattern concrete interlocking paver block with grey cement and pigment confirming to IS 15658-2006 of 100mm thickness, M-50 grade including 50mm thick sand cushioning and filling joints with sand complete all as specified & as directed.

Taking down cement plaster on walls, chajja surfaces, etc including raking out joints, hacking for key, scrubbing down with water complete all as specified and directed.

M&L for rendering 10 mm thick in CM (1:6) on fair faces of brick work or concrete surfaces finished even and smooth without using extra cement complete all as specified and directed

M&L for 5mm thick rendering in CM 1:3 on concrete surfaces in ceiling finished even and smooth without using extra cement complete all as specified and as directed.

M&L for 15 mm thick rendering in CM 1:4 on brick/ concrete surfaces and finishing the surfaces even and smooth without using extra cement complete all as specified and as directed.

M&L for 15mm thick rendering in cement mortar (1:4), in two layers, to fair faces of brick or concrete wall surfaces, top layer 5 mm thick mixed with water proofing compound (@ 2% by weight of cement or as per manufacture's instructions), finished even and smooth without using extra cement complete all as specifed and directed. (Note : Water proofing compound to be measured and paid separately as "Supply only")

Supply only integral water proofing compound complete all as specified and as directed.

M&L Preparing surfaces of wood and wood based materials,steel/metal surface of any description and girth not other wise described and treating small articles such as ends of posts, backs of chowkats,with tar or coal tar black paint etc,area tarred exceeding 0.1 sqm but not exceeding 0.5 sqm each complete all as specified & as directed.

M&L complete removal of existing treatment of plastered surfaces of wall applying wall care putty of 1mm thick average thickness and applying two coats of distemper oil emulsion over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of cement based paint over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of newly plastered surfaces of wall and applying two coats of oil bound distemper over a coat of alkali resistant primer complete all as specified and as directed.

M&L for preparation of new plastered surfaces of wall and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of new plastered surfaces of ceiling and applying three coats of white wash complete all as specified and as directed.

M&L for preparation of old plastered surfaces of wall and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old plastered surfaces of ceiling and applying one coat of white wash complete all as specified and as directed.

M&L for preparation of old wall surface and applying one coat of acrylic exterior weather resistant paint (weather proof paint) of tint as approved complete all as specified and as directed.

M&L for preparation of new wall surface and applying two coats of acrylic exterior weather resistant paint (weather proof paint) of tint as approved over a coat of weather proof primer complete all as specified and as directed.

M & L for preparation of new wood or wood based surface of any description exceeding 10 cm width or girth and applying two coats of synthetic enamel paints over a coat of pink primer complete all as specified and as directed.

M&L for preparation of new steel or iron surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paints over a coat of red oxide, zinc chrome primer complete all as specified and as directed.

S&F 3mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane complete all as specified and directed.

S&F10mm thick toughened glass for door etc complete all as specified and directed.

S&F 4mm thick sheet glass, ordinary quality and glazing with oil putty in square not exceeding 0.50sqm in each pane frosted on one side complete all as specified and directed.

Taking up or down 15 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate

S & F GI tubing 15mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down 20 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate.

S & F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

Taking up or down 25 mm bore GI tubing from trenches / wall including all fittings segregated, cleaning and stacking the pipe for reuse at site if required complete all as specified and as directed. Note : Excavation and earthwork if any shall be included in the quoted rate.

S & F GI tubing 20mm bore, medium grade with all fittings and fixed complete to walls and ceilings or laid in floors complete all as specified and as directed.

S&F 15mm dia Bib taps quarter turn cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F in repair 15mm dia Bib taps quarter turn cast copper alloy chromium plated, with crutch or butter fly handles screwed down for iron pipe or for brass ferrule complete all as specified and directed.

S&F stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F stop valves/ angular stop valve, 20mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F in repair stop valves/ angular stop valve, 15mm dia, cast copper alloy, fancy type, chromium plated, screwed down, high pressure with crutch or butterfly handle screwed both ends for iron pipe or unions complete all as specified and as directed.

S&F 15mm bore pillar taps quarter turn cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F in repair 15mm bore pillar taps quarter turn cast copper alloy with capstan heads chromium plated screwed down high pressure with or without lettered 'HOT' or 'COLD' with long screwed shanks and fly nuts screwed for iron pipe and fixed complete all as specified and directed.

S&F 15mm bore dia of concealed stop valves cast copper alloy fancy type chromium plated with long shank and cup complete all as specified and as directed.

S&F rotational moulded polyethylene water storage tank 1000 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair rotational moulded polyethylene water storage tank 500 litre capacity of triple layered layer wall construction (Cylindrical, vertical with closed top) hoisted and fixed in position including 20 mm dia ball brass valves, high pressure with polythene float and fly nut complete screwed for iron pipe or brass ferrule complete all as specified and directed.

S&F in repair 20mm dia ball brass valves high pressure PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe (Minimum weight 210 gms) complete all as specified & as directed.

S&F in repair fancy type Brass chromium plated 600mm long Towel Rail fixed with screws and wooden/plastic cleats etc. complete all as specified and directed.

S&F in repair chromium plated soap dish of approximate size 160x160x90mm embedded in wall complete all as specified & as directed.

S&F in repair 32mm dia low density polythelene pipes of pressure rating 6kg/Square centimetre complete all as specified & as directed.

S&F 15 mm dia 450 mm long PVC connection pipe with two PVC PTMT nuts at each ends with rubber washer complete all as specified and directed.

S&F grating doom 125mm dia with waste hole of PTMT ( minimum weight 40 gms) including grating complete all as specified & as directed

S&F 110mm trap 'P' or 'S' complete all as specified and directed.

S&F Cast iron nahani trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed

S&F Cast iron nahani trap 100mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed

S&F Cast iron floor trap 75mm dia with grating including jointing to waste pipe fixed in cement concrete type B-I ( 1:2:4) complete all as specified & as directed.

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F 75 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed

S&F 75mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed

S&F in repair 75mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed

S&F in repair 110 mm dia PVC (SWR) pipes, single socketed in any length with rubber ring joints and fixed to wall complete all as specified and directed

S&F 110 mm dia PVC (SWR) bends of any radius complete all as specified and directed

S&F 75 mm dia PVC (SWR) bends of any radius complete all as specified and directed

S&F PVC ( SWR) branch piece, single ( single -Y) equal or unequal 110mm dia with oval access door complete all as specified & directed.

S&F PVC ( SWR) branch piece, single ( single -Y) equal or unequal 75mm dia with oval access door complete all as specified & directed.

S & F 110mm bore PVC ( SWR) junction, single (Single T) equal or unequal with oval access door complete all as specified and directed.

S & F 75mm bore PVC ( SWR) junction, single (Single T) equal or unequal with oval access door complete all as specified and directed.

S & F 75 mm bore PVC (SWR) vent cowl complete all as specified and directed.

S & F 110 mm bore PVC (SWR) vent cowl complete all as specified and directed.

M/L PCC 1:3:6 type C-2 ( 40mm graded aggregate) as in concrete bed to drain pipe 110/150 mm dia including packing under , and haunching against the sides of pipes after they are laid and tested complete all as specified and directed.

Cutting into existing manholes for connecting new drains and making good to pipes and rendering, cutting out existing benching for and forming branch channel ( 1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

S&F in repair Waste coupling 32mm dia of brass chromium plated complete all as specified and directed.

S&F viterous china squatting pan Orissa pattern size 580 x 440mm white with integral foot rest, but excluding flushing cistern but including 'P' or 'S' trap and provision of lime concrete bedding complete all as specified and directed.

S&F in repair viterous china squatting pan Orissa pattern size 580 x 440mm white with integral foot rest, but excluding flushing cistern but including 'P' or 'S' trap and provision of lime concrete bedding complete all as specified and directed.

S&F vitreous china wash basin white flat back size 550 mm x 400mm including all fittings including cutting for and pinning in ends of brackets or erecting stand etc complete (waste coupling 32mm bore CP, 32mm bore PVC waste pipe, cast iron brackets etc shall be deemed to be included in the quoted rate) complete all as specified and directed.

S&F in repairs vitreous china wash basin white flat back size 550 mm x 400mm including all fittings including cutting for and pinning in ends of brackets or erecting stand etc complete (waste coupling 32mm bore CP, 32mm bore PVC waste pipe, cast iron brackets etc shall be deemed to be included in the quoted rate) complete all as specified and directed.

S & F in repairs, mild steel PVC coated coloured 25 mm dia drapery rods for curtains including decorative end holders and brackets (wall to wall or flush to wall) for securing curtain rod,complete all as specified and directed .

S&F PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S&F in repair PVC low level flushing cistern 10 litres capacity with inlet ball valve, float and handles including brackets complete all as specified and directed.

S&F urinal spreader of PTMT any colour for fixing to 15mm dia pipe ( minimum weight 60 gms) complete all as specified and directed.

S&F in repair vitreous china urinal half stall type coloured ( excluding flushing cistern) including urinal spreader, PVC connection, 40mm PVC waste pipe with CP waste coupling 40mm providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc complete all as specified and directed.

S&F vitreous china urinal half stall type coloured ( excluding flushing cistern) including urinal spreader, PVC connection, 40mm PVC waste pipe with CP waste coupling 40mm providing and fixing plugs bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60mm long brass screws pointing around urinal back in cement etc complete all as specified and directed.

S&F PVC connections 15mm dia with PTMT nuts of length 450mm complete all as specified and as directed.

Taking down ceiling/exhaust/wall fan including connection wires carefully, removing to store in safe custody ,painting with synthetic enamel paint by spraying incl. filling cavity and refixing the same in original position after repairing (rewinding if require) including changing the hook ,clamp ,pipe for ceiling fan as per requirement of site complete all as directed

Taking down carefully aluminium/ copper point wiring for light/fan/ socket/bell or power point incl. All fittings i.e. switch, sockets, ceiling rose, regulators, batten holders, etc. complete removing materials to store for keeping in safe custody site or handed over to contractor as schedule of credit and making good disturbed surfaces of walls, floors, etc complete all as directed by Engineer-in-Charge.

M&L for point wiring with 1.5 sqmm, single core, PVC insulated and PVC unsheathed FRLS cable, 1100 volts grade IS-694 marked, with multistranded copper conductors and earth continuity wire with 1.5 Sqmm cable (including connecting to earth dolly) laid/fixed in and including concealed in PVC rigid conduit on walls/ceiling, and also including sunk type pressed steel terminal box made out of galvanised iron sheet thickness not less than 1mm and 3 mm thick plastic laminated sheet top covers for one light/fan/exhaust fan point controlled by one number one way 5 Amp switch complete all as specified and as directed.

All as per item serial No 153 here-in-before but One 3 pin socket outlet 5 amps on the same board with other switches

All as per item serial No153 here-in-before but One socket outlet 3 pin 5 Amp on independent board.

All as per item serial No 153 here-in-before but with 2.5 Sqmm single core multistranded copper conductor cable for 6 pin 15 Amp socket outlet on independent board and earth continuity wire with 2.5 sqmm cable.

S&F switch piano, flush type single pole one way 5 Amps 230 volt complete all as directed.

S&F socket outlet 3 pin, 2-in-1, 5 Amps flush type complete all as directed.

S&F switch socket combination outlet 5 pin, 2-in-1, 5 Amp flush type complete all as directed.

S&F switch socket combination multipurpose, 2 in 1, 6 pin, 5 & 16 Amp flush type complete all as directed.

S&F ceiling rose surface bakelite 65x50mm three terminal complete all as directed.

S&F lamp holder insulated PVC/ Polycarbonate/ bakelite body, with back plate suitable for batten fitting or PVC round or squre box, complete all as directed

S&F stepped type electronic fan regulator, two module size, flush type complete all as directed.

S&F Environmental friendly, ultra modern, energy saving, surface mounted, decorative hexagonal bulk head black-lit LED10 W -IP-66 luminaire comprising of high brightness LEDs complete all as specified and as directed. Make:- Havells Model HEXAFT10WLED857SSYMBOPC or equivalent Model of make : Philips / Crompton /GE /Jaquar.

S&F LED light fitting of approved make 1X 20 W, 220V, AC decorative batten type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. (Make:- Havells /Philips / Crompton /GE /Jaquar or equivalent)

S&F in repair garden Led bollard light aluminium die cast transperant glass difuser, black colour suitable for 20 W LED lamp B-22 base, including lamp of 20W complete all as directed.

S&F in repair LED 40 W post top made in cast aluminium with decorative opal polycarbonate diffuser with IP 65 protection suitable for dia upto 60mm including cage complete all as directed.

S&F in repair round shape 12 W , 220V, AC surface type with high efficiency PMMA difuser soft glare free light complete with driver, holder including LED lamp suitable for roof ceiling and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. (Make:- Havells /Philips / Crompton /GE /Jaquar or equivalent)

S&F in repair LED light fitting of approved make mirror type with high output diffuser 2 feet, 10 W, 220V, AC decorative type with driver, holder including LED lamp and connecting up with three core flexible copper conductor cable of suitable size complete all as directed. (Make:- Havells /Philips / Crompton /GE /Jaquar or equivalent)

S & F SPN DBs 4 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or equivalent model in Siemens / Schneider

S & F in repair SPN DBs 8 Ways, double door, protection class IP-43 suitable for mounting MCB, DBs conforming to IS-13032, IS-8623, BS-5484 with min 100 Amp rating copper bus bar complete all as specified and as directed. Make :- Legrand Cat No 5076 11 or equivalent model in Siemens / Schneider

S&F MCBs, SP 6 to 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4085 90 to 95 orequivalent model in Siemens / Schneider/L&T

S&F MCBs, SPN 32 Amps, 10 KA, 'C' curve IS/IEC 60898-1 2002 marked fixing in DBs complete all as specified and as directed. Make :- Legrand Model 4086 09 to 17 or equivalent model in Siemens / Schneider/L&T

S&F in repair MCCB DB IP-43 of sheet metal enclosure double door VTPN 4 way with 250 Amps rated copper bus bar 415 volt and grouted in wall with PCC(1:2:4) type B-1 using 20 mm graded stone aggregate.(Make-Legrand cat No-5077 45 or equivalent model in Siemens / Schneider) .

S&F in repair MCB TPN 40 to 63 Amps in accordance with IS/IEC 60898-1, 415 V, 50 Hz,10 kA,C-series rupturing capacity providing in DB complete all as specified. (Make :- Legrand / Siemens/Schnider)

S&F in reapir MCCB 415 Volts, 16 KA, 4P 125 Amps complete all as specified and as directed.

M&L in repair Sub main wiring with 2 runs of 4.0 sqmm, single core, FR-LSH PVC insulated & unsheathed cable conforming to IS-694, 1100 volts with copper conductor multi stranded drawn in and including 20mm dian non metallic PVC grey conduit with all accessories such as Tees, Elbows, junction box, reducers etc as requied alongwith one run of 4.0 sqmm single core FR-LSH PVC insulated & unsheathed copper conductor as continuos earth wire dolly and connecting to existing main switch board / distribution board of each building / qtr as ordered and testing on completion complete all as specified and directed. (Note: 2 run of 4 Sqmm cable and 1 run of 4 Sqmm cable along with conduit all together shall be measured as one unit.)

M&L in repair cable junction box of size 130X130X77mm, IP-66 with metric knockout for cable entry ( Dust and power jet proof according to IEC60529), shock proof, rust free, corrosion free, acid and chemical resistant, fire retardent having high impact ( IK08) totally insulated ( ClassII) made of helogen and silica free recyclable material UV resistance having high rate gasket made of polyurethene, one number MCB DP 6 Amps with locking arrangement and M 40 size cable gland and one M32 size gland suitable for 2.5-6.0sqmm cablecomplete all as specified and directed.Make : HENSEL cat No. DK 0600 G or equivalent as approved

Supply,and fixing 1100volts grade heavy duty cable PVC insulated aluminium conductor of size 4 sqmm, 2 core served with inner sheathing of PVC tape and overall PVC sheathed in service connection suspended by insulating hanger not more than 1.00m apart including 4mm suspension wire, one twin cable flat or circular, drawn in and including suitable size of non metallic PVC grey conduit with all accessories such as Tees, Elbows, Junction box, reducers etc as required complete all as specified and as directed.

Supply, laying and testing of XLPE insulated, PVC sheathed, armoured, heavy duty electric under ground cable, with stranded aluminium conductor, 1100 Volts grade of size 25 sqmm 4 core laid in trenches / floor or fixed on wall /pole with brass compression cable glands, terminal lugs etc, including taking out/down old cablecomplete all as specified and as directed.

Supply and lay GI tubing 25mm bore light grade for cable protection and fixing to the existing pole with flat iron clamp 25x 3mm including nut bolts complete all as specified and as directed.

Supply and spreading fine dry river sand for cushing to UG cable including spreading levelling and hand punning etc complete all as specified and directed.

M&L for sub class 'B' old size bricks laid in trenches for cable protection laid flat width wise along the length of cable complete all as specified and directed.

S&F of Exhaust fans AC single phase 230/ 240 V ,50 Hz metallic heavy body of size 300 mm sweep, 900 RPM with louver fixing with 4 no hold fastener nut and bolt with washer and connecting with flexiable PVC insulated multistranded copper conductor cable of size 1.5 sqmm including civil work opening on wall and making good surface complete all as specified and directed. (Make-USHA, Model-300MM S.PH TURBO HDEF 900 RPM or equivalent model of make Havells/Bajaj /Crompton)

Earthing complete with GI earth plate electrode of size 60cm x 60cm x 6mm buried directly in ground vertically at a depth not less than 2.25 metre below normal ground level with top edge of earth plate at a depth not less than 1.5 metre below normal ground level sorrounded from all sides by 15cm thick and packed layer of charcoal dust and common salt fliing in alternate layers etc and connected to and including galvanised earth lead wire 4 mm upto 7.5 mtr by means of bolts, nuts, check nuts and washers made of galvanised iron and protected by light grade 20 mm dia GI pipe connected to main control board and GI pipe medium grade 40 mm bore for watering and including funnel, wire mesh, charcoal salt etc RCC pit cover flush to earth pit 50mm thick reinforced with 8mm TMT bar 100mmC/C and PCC chamber pit with PCC (1:3:6) type C1 (using 20mm graded aggregate) including earthwork disposal of surplus soil to distance not exceeding 50 metre) and testing after completion all as specified and shown on plate No 3 of SSR Part-I 2009 .