SPECIAL REPAIRS TO BLDG NO P-115, P-318 AND P-1842 IN CERTAIN UNITS AT MIL STN, JAISALMER

Amount

Excavating in trenches not exceeding 1.5m wide and not exceeding 1.5m in depth for foundation, laying of cable/pipe etc or for shafts, wells, cesspits, manholes, pier holes etc not exceeding 10 Sqm on plan and getting out in soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Returning, filling in, including, spreading, levelling, watering and well ramming in layers not exceeding 25 cm thick with soft/ disintegrated rock complete all as specified & directed by Engineer-in-Charge.

Removing excavated material soft/ disintegrated rock to a distance not exceeding 50 m and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed by the Engineer-in-Charge.

Demolition of Concrete reinforced (reinforcement cut as required to facilitate demolition) of any description and in any position not otherwise specifically provided for complete all as specified & directed by Engineer-in-Charge. Note :- Item scrap obtained from demolition of RCC shall be issued to conractor under respective items of Schedule of credit.

Demolition of cement concrete unreinforced in ground floors and pavings not exceeding 15cm thickness (below or above ground level) and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m complete all as specified & directed by Engineer-in-Charge.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and rubbish off the premise complete all as specified and directed by Engineer-in-charge.

Dismantling wrought iron or mild steel work of any description not otherwise provided for complete all as specified & directed by Engineer-in-charge.

M&L for 25mm thk PCC (1:2:4) type B-0 (using 12.5mm graded stone aggregate) as in subbase of floors & finishing the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L for machine cut kota stone slab flooring 20 to 25mm thick laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing laid over and including screed bed or bedding layer of 15mm thick in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L for machine cut kota stone slab 18 to 20mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with pigment to match the shade of the slab including rubbing and polishing complete laid over and including 15 mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

S&F glazed ceramic coloured tiles of size 350 x 250mm x 7mm / 450mmx350mmx7mm thick on vertical surface such as skirting, dados, risers to steps etc set & jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including racking out joints, hacking for key, scrubbing down with water etc and removal of rubbish off the premises and leaving the work clear of any plastering complete all as specified & directed by Engineer-in-charge.

M&L for rendering 15 mm thick plaster in cement mortar (1:6) on fair faces of brick work or concrete surfaces of walls and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for rendering 15mm thick in cement mortar (1:4) in two layer (First coat 10 mm thick and second 5 mm thick) mixed with using water proofing compound @ 3% by weight of cement and finishing the surface even and fair without using extra cement all as specified & directed by Engineer-in-charge. Note :- Supply only WPC will be measured and paid separetly.

M&L for rendering 5 mm thick plaster in cement mortar (1:4) on concrete surfaces of ceiling and finishing the surface even and smooth without using extra cement all as specified and directed by Engineer-in-charge.

M&L for preparing new plastered or unplastered surfaces and applying three coats of white wash on wall all as specified & directed by Engineer-in-charge.

M & L preparation of new plastered surfaces and applying three coat of white wash on ceiling complete all as specified & directed by Engineer-in-charge.

M&L for preparation of newly plastered surfaces of walls and applying two coats of colour wash over one coat of primer complete all as specified & directed by Engineer-in-charge.

M&L for preparing old decorated plastered surfaces of walls by brooming down or by steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

M&L for preparing old decorated plastered surfaces of ceiling by brooming down or by steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of white wash complete all as specified & directed by Engineer-in-charge.

M&L for preparing old decorated plastered surfaces of walls by brooming down or by steel wire brushing scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots and applying one coat of colour wash complete all as specified & directed by Engineer-in-charge.

M&L for preparing old decorated surfaces of walls by washing, rubbing down and stopping of painted surfaces and applying a coat of cement base paint complete all as specified & directed by Engineer-in-charge.

M&L for preparation of old painted steel surfaces of any description not otherwise described over 10cm width or girth and applying one coat of synthetic enamel paint complete all as specified & directed by Engineer-in-charge.

Hacking out old broken glass (any thickness, size quality or description) from wood /steel frame glazed with oil putty or fixed with beads and S&F plain sheet glass of 3 mm thick ordinary quality and glazing with oil putty and clips in squares not exceeding 0.50 Sqm in each pane complete all as specified & directed by Engineer-in-charge.

M&L welding in repair exc 2.5cm but not exceeding 5cm in length (thickness of metal to be welded not exc 6mm) including cleaning preparing the surface and holding the member in true position complete all as specified & directed by Engineer-in-charge.

M&L Mild framed works such as angles, tees, channels, etc as in fenching posts large and small gates and grills, gratings and chainlink fenching etc, including hanging gates in pillar with proper pintle hinges, stops, hand made sliding bolts,etc complete all as specified & directed by Engineer-in-charge.

Taking down old steel window/ventilators of any description not otherwise specified and in any position complete all as specified & directed by Engineer-in-charge.

S&F steel ventilators with top hung shutters fitted with box type hinges including MS peg stays, MS handle and glazing bars dovetailed or welded for receiving glass including painting with one shop coat of zinc chromate primer and cutting holes in wall for fixing the window lugs with and including bed blocks in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified & directed by Engineer-in-charge. Note : The rates quoted are inclusive of bed blocks and making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

S&F steel window with side hung shutters fitted with box type hinges including MS handles, peg stays, MS guard bar made out of 10 mm squre bar, glazing bars dovetailed or welded for receiving glass and including painting with one shop coat of zinc chromate primer including cutting holes in wall for fixing the window lugs with and including bed blocks in PCC 1:2:4 type B1 using 20mm graded aggregate and making good the disturbed surfaces in CM (1:3) and applying two coats existing wall finishes to match with existing colour complete all as specified & directed by Engineer-in-charge. Note : The rates quoted are inclusive of bed blocks and making good all the disturbed surfaces to match with the adjoining surfaces and necessary scaffolding etc up to 4th floor.

M&L for preparation of new or previously untreated steel surface of any description, over 10 cm width or girth, not otherwise described and applying two coats of synthetic enamel paint (ordinary tint) over a coat of red- oxide, zinc chrome primer complete all as specified & directed by Engineer-in-charge.

Supply only integrated water proofing compound complete all as specified & directed by Engineer-in-charge.

Taking down the existing roof treatment of any description, any thickness and removing the debris not exceeding 1000 m complete all as specified & directed by Engineer-in-charge.

M&L for providing 3 mm thick APP modified memberane over RCC roof with the following specifiations :-

ITEM NO. 33.00 CONTD... (a) Cleaning existing surface properly. (b) Apply oil bound bitumen primer @ 0.40 lit/Sqm manufactured by the same agency as that of APP with a density of 0.87 -0.89 Kg/Lit at 25 Degree Centigrade on the prepared dry roof surface. (c) Providing and Laying APP modified water proofing membrane reinforced with non wooven polyster matt with physical propertities as under :- (i) Membrane weight >3.6 Kg/Sqm . (ii) Net wooven polyster weight >160 gm/Sqm (iii) Softening point of membrane > 150o C (iv) Joint Tensile strength Longitudiual > 650 Sq Cm at 230o C & Transverse > 450/ Sq cm (v) Tear strength - Longitudual > 300 N & Transverse > 250 N Direction (vi) Elongation > 30 %

ITEM NO. 33.00 CONTD... (vii) Impermeability under water pressure > 3 Kg/Sq cm Note:- APP membrane shall be laid using butane torch by Torch application with minimum 10 cm side overlap and 15 cm end lap. The laying of membrane shall be got done through authorised applicator of manufacturer of membrane. (d) Over the membrance provide a finishing with solar reflective bituminous aluminium paint @ 0.1 Kg/Sqm as prescribed by manufacture of membrane

S&F rolled sections as in main and cross beams, hip and jack rafters, purlins where connected to common rafters and running rails and guides for sliding doors, fixed with angle cleats or other connecting plates conforming to Fe 410-W (Gde E-250 quality-A) complete all as specified & directed by Engineer-in-charge.

Demolition of brickwork or stone/ boulder masonry and built in cement mortar including all quoins arches, pillars etc but excluding ashlar facings, dressed stone work and precast concrete articles and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

M&L for squared rubble walling, Jodhpur type, brought upto courses, well bonded, bedded and solidly hearted, built in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

Extra over stone walling for hammer dressing to face stones with maximum depression on face from a straight edge not exceeding 20mm & dressing face beds and joints as specified to squared rubble walling Jodhpur type brought up to courses complete all as specified & directed by Engineer-in-charge.

Surface excavation not exceeding 30cm and averaging 15 cm deep and getting out in hard/dense soil complete all as specified & directed by Engineer-in-charge.

Removal of excavated soil exceeding 250m but not exc 500 m and depositing where directed at a level not exc 1.5 m above the starting point complete all as specified & directed by Engineer-in-charge.

M&L for hardcore of gauge not exceeding 63 mm of broken stone or boulders, deposited, spread and levelled in layers not exceeding 15 cm thick, watered and rammed to a true surface complete all as specified & directed by Engineer-in-charge.

M&L for 75 mm thick cement concrete (1:4:8) type D-2 using 40 mm graded stone aggregate as in sub base of flooring/ hard standing path & finishing the surface even & fair without using extra cement complete all as specified & directed by Engineer-in-charge.

M&L Machine pressed precast concrete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness, M-35 Grade with grey cement and pigment laid over and including 25mm thick sand cushioning complete all as specified & directed by Engineer-in-charge. Note :- (i) Pattern of interlocking tile to be rubber moulded or equivalent as approved by GE. (ii) Rate quoted by the contractor shall deemed inclusive of PCC (1:2:4) type B-1 (using 20 mm graded stone aggregate) packing and finished even and fair to the sides of pavement.

M & L for ceramic tiles exterior grade 300 x 300 x 10mm laid over and including 15mm thick screed bed in CM 1:6, set and jointed in neat cement slurry and pointed in coloured cement to match and roughening of exc concrete surfaces complete all as specified & directed by Engineer-in-charge.

M&L for renforcement cement concrete nominal mix 1:2:4 type B-0 (using12.5 mm graded stone aggregate) for chajja, roof projection, facies and similar works complete all as specified & directed by Engineer-in-charge.

M&L use and waste formwork to chajjas, roof projection and similar work including edges with rough finished surfaces of concrete including height upto 6 mtr complete all as specified & directed by Engineer-in-charge.

M&L for mild steel TMT bars 6mm to 8mm dia & over cut to length, bend to shape required, including cranking, bending spirally for hooping for columns hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified & directed by Engineer-in-Charge.

M& L plain cement concrete 1:2:4 type B 1 using 20mm graded stone agregate cast in situ kerb stone, copings, bed plates, water through and the like including wethering, slightly rounded or chamfered angles and throating including use of form work (straight or curved ) set in CM 1:4 complete all as specified & directed by Engineer-in-Charge.

S&F steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer, thickness of lath 1.0mm, erected in position as indicated complete push pull or manual type and including taking down existing rolling shutters of any thickness complete all as specified & directed by Engineer-in-charge.

Taking down chowkats or frames (without taking off shutters from the frames) area exceeding 1.5 Sqm but not exceeding 4 Sqm each complete all as specified & directed by Engineer-in-charge.

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specifically provided and removal unserviceable materials, debris and rubbish to a distance not exceeding 100m all as specified & directed by Engineer-in-charge.

M&L for precast cement concrete (1:3:6) type C-1 (using 20mm graded stone aggregate) as in block masonry with solid blocks exceeding 10cm width and setting in cement mortar (1:6) complete all as specified & directed by Engineer-in-charge.

M&L for preparation of new plastered surfaces of walls and applying two coats of distempering oil emulsion over a coat of primer and one coat of wall putty to get a uniform smooth surfaces all as specified & directed by Engineer-in-charge.

S&F anodised aluminium snap grid frame work 605x605mm for false ceiling and hangers 6mm dia, GI (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3mm size 60mm long and expansion hold fastener 12.5mm dia 40mm long including 12 mm medium Gymsum board, exterior grade with screws complete all as specified and directed by Engineer-in-charge. Note :- (i) Main tee, cross tee shall be 35x25x1.5mm & 25x25x1.5mm respectively. Angle at end all along the walls shall be 40x25x2mm. (ii) Rate quoted by the contractor shall deemed to inclusive of frame work & ceiling board complete.

M&L for preparing surface of any description and applying two coat of plastic emulsion paint over a coat of primer and cement based putty for uniform smooth surface complete all as specified and directed by Engineer-in-charge.

M&L light shade, vitrified tiles, 10mm thick (minimum), (square/ rectangular polished, area of each tiles not exceeding 0.36 sqm (including 600mmx600mm size), in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour of tiles laid over and including screed bed or bedding layer of mortar 15mm thick for laying floor finishes in CM (1:6) complete all as specified & directed by Engineer-in-charge.

M&L vitrified tiles of light shade, 10mm thick (minimum) (square/ rectangular) polished area of each tiles equal to or not exceeding 0.36 sqm (including 600mmx600mm size), in skirting/dado etc., set and jointed in neat cement slurry and pointed in white or coloured cement to match the colour tiles laid over and including 10mm thick backing coat in CM (1:4) complete all as specified and directed by Engineer-in-charge.

M&L for Anodised aluminium frame powder coated (minimum thickness of powder coating 50 micron) for doors, windows ventilators with one or more rebates including joining cleat for fixing etc complete all as specified and directed by Engineer-in-charge.

S&F for anodised aluminium powder coated (minimum thickness of powder coating 50 micron) window and ventilator shutters, side hung type without sash bars, aluminium sections weighing 0.55 kg/m including necessary joining cleats, glazing clips, rubber packing, anodised aluminium snap beading, screws, anodised aluminium fittings such as peg stays 150mm long (1 no.). hinges type B-21 100mm long (2 no.) suitable handle (1 no.) complete all as specified and directed by Engineer-in-charge.

S&F anodised aluminium powder coated (minimum thickness of powder coating 50 micron) door shutters, aluminium section weighing 0.55 kg/ m including necessary joining cleats, glazing clips, ruber neoprene packing, handles 2 Nos in each door, hinges, anodised aluminum snap beading screws etc. complete all as specified and directed by Engineer-in-charge.

S&F 4.8 mm thick sheet glass ordinary quality and glazing with oil putty or wooden beads in squares exceeding 0.50 Sqm in each pane complete all as specified and directed by Engineer-in-charge.

S&F aluminium (Die cast) door closer hydraulically regulated designation No. 3, universal type, suitable for door shutter of 851 mm to 1000mm in width and of weight between 61 to 80 Kg complete all as specified & directed by Engineer-in-charge.

M&L for granite (of any type) tiles 20mm thick machine cut, bedded and jointed with grey cement slurry and pointed with white cement with admixture of pigment to match the shade of granite stone including grinding and polishing complete all as specified & directed by Engineer-in-charge.

S&F in repair PVC connections 450mm long, 15mm size with PTMT nuts for WHB, flushing cistern, geysers etc complete all as specified & directed by Engineer-in-charge.

S & F, 35 mm thick second class hard wood factory made plain, framed, panelled shutters, with lock rail and panel of 9mm BWP commercial ply or 12 mm veneered particle board with commercial veneering on both faces. The size of rail and Style as per IS:1003 (Part-1), kiln seasoned and chemically pressure treated complete all as specified & directed by Engineer-in-charge.

S & F 18/19mm thick pre-laminated particle board, exterior grade, prelaminated both side with decorative choice lamination & other side balancing white lamination alround 6mm th teak fillets fixed in kitchen CB or pelmet complete all as specified & directed by Engineer-in-charge.

M&L for 2nd class hard wood fillets square, rectangular as in lippings fixed with nails of area exc 3Sqcm but n.exc 6sqcm complete all as specified & directed by Engineer-in-charge.

S & F 40mm width of flaps (when open) continuous (piano) hinges, mild steel bright finish or electroganised fiwed to wooden or angle iron frame complete all as specified & directed by Engineer-in-charge.

S&F 40mm dia, cupboard knobs fixed with nut, screw and washer of mild steel, bright finished complete all as specified & directed by Engineer-in-charge.

S & F, 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., (without sash bars), edges of framing plain, chamfered or rounded, fitted with cut and mitred beads for securing glass, etc size of members of shutters as specified in SSR Part-I, section 8, clause 8.24 (a) complete all as specified & directed by Engineer-in-charge.

S&F 150 mm size aluminium anodised barrel tower bolts of extruded section all as specified & directed by Engineer-in-charge.

S&F in repair 300mm long aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified & directed by Engineer-in-charge.

S&F in repair, 140mm long floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, fixed in floor complete all as specified & directed by Engineer-in-charge.

S&F in repair aluminum anodised barrel tower bolts of extruded section with 150 mm long bolt complete all as specified & directed by Engineer-in-charge.

S&F in repair 150 mm size aluminium handle, cast type, anodiesed complete all as specified & directed by Engineer-in-charge.

S&F in repair, 100mm size Butt hinges, extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type C-21 complete all as specified & directed by Engineer-in-charge.

S&F 15mm bore dia steel water tubing (ISI marked) medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors including taking down existing pipe complete all as specified and directed by Engineer-in-charge.

S&F 20mm bore dia steel water tubing (ISI marked) medium grade galvanised with all fittings and fixed to walls and ceiling or laid in floors including taking down existing pipe complete all as specified and directed by Engineer-in-charge.

S&F in repair 15mm dia bib taps (long body) cast copper alloy chromium plated with crown or capstan head, screwed down, high pressure screwed for iron pipe complete all as specified and directed by Engineer-in-charge.

S&F in repairs 15mm dia stop valves fancy type cast copper alloy chromium plated screwed down high pressure with crown or capstan head screwed both ends for iron pipe complete all as specified and directed by Engineer-in-charge.

S&F sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe, overall size 495mm x 420mm bowl size 410mm x 330mm x 160mmg including CP waste coupling & brackets and fixed complete all as specified and directed by Engineer-in-charge.

S&F in repair PVC down take waste water pipe for WHB of size 32 mm dia and 60 cm long complete all as specified and directed by Engineer-in-charge.

M&L Preparation of old decorated surfaces of wall including brooming, scraping down. Smoke spot, moss, efflorescent salts, trading oil, grasy spots and stopping nails marks by applying white cement base putty in patches as required and one coat of oil bound distemper complete all as specified and directed.

M&L for preparation of new painted wooden surfaces of any description not other wise described over 10 cm width or girth and applying two coat of synthetic enamel paint over a coat of pink primer complete all as directed by Engineer-in-Charge.

M&L for preparation of old painted wooden surfaces of any description not other wise described over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as directed by Engineer-in-Charge.

S & F anodised aluminium alloy Harrison rails, mild steel, chromium plated with fixing brackets, stops, rollers etc. (Curtain rods) complete all as specified and directed by Engineer-in-charge.

S&F in repair CP grating (with & without hole) for Nahani trap and floor trap of size 100 mm dia complete all as specified and directed by Engineer-in-charge.

S&F in repair, 100 mm size hasp and staple, safety type, aluminium anodized with mild steel hinge pin including bolt to hinge plate and fixed with screws /fixed complete all as specified and directed by Engineer-in-charge.

S&F aluminium alloy wire cloth, 0.45mm nominal dia of wire and average width of aperture 1.40mm and fixed with aluminium wire staples complete all as specified and directed by Engineer-in-charge.

Taking down copper/aluminium point wiring (light, fan, socket or power ) complete including fixture and fittings such as swithces, ceiling roses, pendants, regulator, socket, light fitting etc, removing materials to store for keeping in safe custody or for taking credit (credit for above items shoube be made as per condition separetly ) and making good distured surface of wall ,floors etc complete all as specified and directed by Engineer-in-charge.

Taking down the existing unserviceable main switch / cut out / DBs of any type / capacity / description as existing at site including MCBs any type and capacity making good the disturbed surfaces to match with the existing finishes complete all as specified and directed by Engineer-in-charge.

Taking down the existing unservicable sub main wiring of any type / description as existing at site including making good the disturbed surfaces to match with the existing finishes complete all as specified and directed by Engineer-in-charge.

Taking out carefully copper/GI earthing complete including GI pipe with Cu/GI strip and removing materials for taking credit and making good disturbed surface complete all as specified and directed.

M& L Point wiring with 1100 volts grade PVC insulated FR-LSH multistranded copper conductor cable 1.5 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 1.5 sqmm (Green) drawn into and including concealed rigid non metallic PVC conduit medium grade not less than 20 mm dia ISI marked ivory colour with all conduit fittings / fixing accessories and sunken galvanized pressed steel terminal boxes of thickness not less than 1.2 mm with 3 mm thick phenolic laminated white sheet cover for mounting of Piano Type switches, sockets, fan regulators complete for the following :-

(a) One light point controlled by one switch.

(b) One socket outlet 6 amp controlled by one switch on the same board with other switches.

(c) One socket outlet 6 amp controlled by one switch on indepdendent board.

All as per item No 93.00 here-in-before but of size cable 4.0 sqmm (Phase - Red, Neutral - Black) and earth continuity conductor 4.0 sqmm (Green) for one 16 amp socket outlet controlled by one switch on independent board complete.

S&F switch piano, flush type, 6 amps, 230 volts, single pole, one way complete all as specified & directed by Engineer-in-charge.

S&F switch piano, flush type, 16 amps, 230 volts, single pole, one way complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 3 pin 6 & 16 amp flush type complete all as specified & directed by Engineer-in-charge.

S&F socket outlet 2 in 1, 2 & 3 pin, 6 amp, flush type complete all as specified & directed by Engineer-in-charge.

S&F hum free electronic step fan regulator 120 - 280 volts of 100 watt capacity (socket type) including connecting up complete all as specified & directed by Engineer-in-charge.

S&F of switch piano, flush type, 16 amps, 230 volts, single pole, two way (ISI marked) complete all as specified & directed by Engineer-in-charge.

S&F Ceiling rose, three terminals PVC/polycorbonate, isolated body complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 12 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

S & F for MCB DB SPN 4 way double door IP 43 complete prewired including Bus Bar etc suitable for operation on 240 volt 50 Hz AC supply including necessary provision for inserting the DBs in wall by cutting the brick/stone masonary etc and making good of distrubed surface to match with existing colour of wall complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole and neutral 32 Amps, 240 Volts, 10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing MCB's single pole 6 Amps to 32 Amps, 240 Volts,10 KA rapturing capacity 'C' curve complete all as specified & directed by Engineer-in-charge.

Supply and fixing of building security light fitting LED 35 Watt IP 66 IK 07 pressure dia cast aluminium housing with high efficient LED as lihjting souce and PC cover having TOP opening sepreate drive compartment etc and connecting complete all as specified & directed by Engineer-in-charge.

S&F GI pipe bracket medium grade of 40 mm dia for building security light, clamps made of FI 40 mm x 6 mm Incl nuts, bolts & washers including two coats of synthetic enamel paint over a coat of zink chrome primer including taking down existing unserviceable bracket of any description complete all as specified and directed by Engineer-in-charge.

Supply and fixing of LED box type Integrated Batten 40 watt having Aluminium Extruded housing in white powder coated Finish with high translucent PC Cover, Elegant Design, IP 20 Protection. Dimensions of the Fitting Shall be Not less then 1200 MM ( Length) X 40 MM ( Width ) X 63 MM ( Height ). Lumens output of the fitting shall be not less then 4400 lm, CCT 5700 – 6500K, Surge Protector 4 KV, PF>= 0.95 , Separate detachable type Electronic constant current drivers for easy replacement and maintenance, THD < 10% , Operating Voltage Range – 140 -270 Necessary mounting arrangements. The Manufacturer of the fixture shall have in house NABL Accredited Lab and must produce certificate of the same along with LM-79 / LM-80 / Test Report as Per Crompton Cat Part No. CIS-305-40-57-SL-DP-NWH or equivalent in Appx 'C' list of makes.

M & L for submain wiring with approved colour code/as per IS (Red,black & green for single phase) concealed conduit circuit with two single core PVC insulated cable with multistranded copper conductor of nominal cross sectional area of 4.00 Sqmm (FRLS) in conduit including one run of PVC insulated multistranded copper conductor nominal cross sectinal area of 4.00 Sqmm (FRLS) of continous earth wire green in colour complete all as specified and directed by Engr-In-Charge. (Note :- Two runs of 4.00 Sqmm cable & one run of 4.00 Sqmm cable as earth wire and one run of PVC conduit shall be measured and paid as one unit length)

S& F Air Circulation Heavy Duty Wall Mounting fan sweep size 450 mm, oscillating function, RPM 1400 or more and having air dilivery of 16000 CMH complete all as specified & directed by Engineer-in-charge.

M & L bore earthing not less than 250 mm dia 16 feet deep filled with black soil up to 7 feet from bottom complete with galvanized iron pipe 40 mm bore medium grade 3 meter long tapers at bottom & provided 12 mm holes (staggered) at 75 mm centre to centre up to 2.5 meter of length from bottom , burried directly in ground filled with 45 cm alternate layer of chemical magnisium sulphate, charcoal & salt up to ground levl connected to galvanized iron strip 25x4 mm as earthing lead up to 7.5 mtr by means of bolt and nut, check nuts and washer of galvanized iron or steel including brazing work and 40mm dia light grade pipe for earth lead protection and testing complete all as specified & directed by Engineer-in-charge.

NOTE FOR ITEM No. 111.00 [i]. Excavation & earth work in any type of soil including removing of surplus material upto 100M [ii]. PCC (1:3:6) type C1 using 20mm graded stone aggregate in pit & 40mm thick precast RCC (1:2:4) type B1 cover 50x50 cm with 8mm round bar @ 15 cm C/C both ways. [iii]. Main earthing strip from earth electrode to test point upto 7.5 mtr. [iv]. Funnel with watering pipe [GI pipe] 20mm bore [ISI marked] medium grade & copper lugs and charcoal & salt as reqd. [v]. GI protection pipe of size 40 mm bore light grade 7.5m.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in pipe or fixed to DBs or any other indicated situation for loop earthing with GI strip of 25X4 mm size complete all as specified and directed Engg-in-Charge.

S&F steel water tubing 40 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable etc and including taking down existing pipe of any description complete all as specified & directed by Engineer-in-charge.

S&F steel water tubing 20 mm bore, 'light grade' galvanised, with all fitting and fixed complete to walls and ceilings or laid in floors in trench on pole for protection of cable etc acomplete all as specified & directed by Engineer-in-charge.

Supply, laying and testing LT XLPE insulated, armoured heavy duty, electric cable, with aluminium conductor, 1100 volts grade, cross-sectional area 16 Sqmm 4 Core complete all as specified & directed by Engineer-in-charge.

M&L for sand cushioning to under ground cable using tibba sand and gently punning to cushioning to cable complete all as directed by Engineer-in-Charge. (Note :- Punned thickness of sand cushioning shall only measured for the purpose of payment).

Supply & laying 40 to 50mm thick roughly hammer dressed Jodhpur stone patti cable cover 25cm to 30cm wide and not exc 60cm long each laid dry abutting with each other with maximum gap between adjacent slabs n. exc 10mm complete all as specified & directed by Engineer-in-charge.

MARUDHARA CONSTRUCTION COMPANY

S K TRADER

M/S MAYA CONSTRUCTION COMPANY

AMBEY MAA CONSTRUCTION COMPANY

M/s Shree Construction Company

Leelashah Enterprises

M/s Shri Inder Construction Company

M/S OM VISHNU ENGINEERING & CONSTRUCTION COMPANY

GEMRARAMCONTRACTOR

Bhawani Constructions