Construction of Compound wall and Toilet for ICDS at Neelikonam palayam in ward no 54 East zone

1.Earth work excavation in all kinds of soil including sand, silt, wet sand under water, black cotton, stiff black cotton, clay, hard stiff clay, hard red earth, murram, stoney earth, gravel and shales etc. excepting all kinds of rock and boulders exceeding 0.014 c.u.m. in volume including rough dressing and dumping the excavated materials away from work site manually within 50m initial lead and 2m initial lift as per the direction of Engineer-in-charge.

2.Cement concrete 1:4:8 (one cement, four sand and Eight aggregate) using 40mm gauge hand broken granite stone jelly for foundation including dewatering if found necessary and laid in layers of not more than 15 cm thick and compacted, etc., complete complying with standard specification.

4.Supply and fabrication of R.T.S. rods in various dia including cutting bending placing in position and tying etc.

5.Supply and erecting shuttering including necessary supports for plane surfaces such as RCC column, footing, plinth beam, stair case etc., in all floors using mild steel sheets of 90cm X 60cm and 10 gauge stiffened with welded mild steel angle for boarding supported by casurina props at suitable intervals etc., completed complying with standard specification and as directed. Sl.No.122

6.Cement concrete 1:1.5:3 (one cement, one and a half sand and three aggregate) using 20mm gauge hard broken granite stone jelly for All RCC items of work excluding centering, shuttering, and cost of reinforcement grill but including curing finishing etc., complete and also including fixing fan clamps and fixtures in RCC works wherever necessary as directed by departmental officer etc., complete.

7.Brick work in cement mortar 1:5 mix (one cement five sand) using II class table molded bricks chamber burnt bricks of size 9" X 4 1/2" X 3" for the following including curing etc., completed.

8.Supply and fixing of mild steel door using all round "L" angle 25 X 25 X 6mm thick, cross bracing 20 X 6mm M.S.Flat with necessary locking arrangements including cost and conveyance etc., Size : 0.60 X 1.85 = 1.11 m2

10.Supplying, fabricating, erecting structural steel work for roofing welded or bolted type using MS channels, angles, plates, square and rectangular tubes and round bars etc. conforming to IS specification including primer coating and enamal painting as per Design given by the departmental officers etc,complete as per standard specification

11.Fabricating supplying and fixing of Pre Painted Galvanium Iron Sheets with the following specification. The materials should be of PPGI tile profile with a red colour or any other approved design 0.47mm thick 24 guage having width 1050 mm. The sheet should be G.I.base pre painted hot dipped galvanized iron sheet and to be fixed with shelf tapping screws,plastic washer.The washer and screws to be fixed by using minute power machine drilled with out damaging the sheets paint coating to be regular modified polyster coat with zinc coating of Z 120 GSM paint thickness the finish should be terra cotta finish like malabar mangalore tiles finish optional matt finish. The sheet to be fixed with making suitable corrugated,cutting the sheet in to the required ssize and making ornamental designs as per the site condition and as directed by the departmental officers.

12.Plastering with cement mortar 1:3 mix (one cement and five sand) 12mm thick

13.Plastering with cement mortar 1:5 mix (one cement and five sand) 12mm thick

14.Flooring with scratch proof Ceramic Tiles of approved quality and colour of size 305x305x6mm in all floors over 20mm thick cement mortar 1:3 (One cement and three sand) base above the existing bed concrete and pointed with same color cement added.

15.Daddoing the walls with first quality approved colour glazed tiles with printed design of 150X150X6 mm laid in cement mortar 1:2 mix to 10mm thick and painting with white cement using 0.40 kg/1m2 including finishing the jointing and painting flush with tiles surface etc., complete - 10 m2

16.Solid PVC Door with frame Shutters using 19 Gauge 19mm MS square tubes for styles and outer frames. 15mm MS square tubes for top, lock and bottom rails. The steel tubes shall be covered with 5mm thick solid PVC Sheets. Shutter using 5mm thick solid PVC Sheets for panelling shall rigidly fixed in position including necessary furniture and fittings. The over all size of styles shall be 50mm x 30mm. The over all size of top rail, lock rail and bottom rail shall be 75mm x 30mm. The over all size of frames shall be 50mm x 45mm with suitable rabate for housing the shutter

17.Painting with emulsion paint paint two coats over a priming coat including through cleaning, scrapping, removal of dust and including necessary plaster of paris putty works wherever required etc., completed.

18.Painting new iron work for doors, windows, grills, weld mesh sceens etc., two coats etc complete

19.Wiring with 2x1.5 sq.mm. (22/0.3) PVC insulated unsheathed SC copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with PVC accessories with TW switch box with 5A FT switch inflush with wall covered with hylumsheet of 3mm thick with painting of suitable colour for open PVC light/fan point (for electronic regulator) (5 points per coil) SD-19

20.Wiring with 2x1.5 sq.mm (22/0.3) PVC insulated SC unsheathed copper conductor of 1100V grade insuitable PVC rigid pipe on wall and ceiling with PVC accessories with 150x100x113mm TW switch box for 5A 3pin non interlocking Wall socket with 5A flush type switch with painting of suitable colour with continuous earth wire connection of 14 SWG TC wire for open PVC plug point SD-34

21.Supply and run of 2 of 4sqmm PVC insulated SC unsheathed Cu.conductor of 110V grade in suitable PVC rigid pipe concealed in wall and ceiling with contious Earth wire and making good of the concealed portion with siutable colour etc complete SD-46

22.Supply and fixing of ceiling fixture 250/300mm complete with gallery etc clear glass Opac/Crystal suitable for 40W / 60W bulb with bulb SD-86

23.Supply and fixing of 4'40W twin street light fluorescent fitting complete with copper choke and condensor with 32mm dia GIpipe (Class'B') with 1No.32mm GI bend complete on the existing post wall with 16A aerial fuseunit on MS plate with PVC unsheathed copper leads MS clarnps and aluminium painting with fluorescent tubes SD-94

24.Supplying and fixing in position best white glazed earthernware Oriya type Indian water closet of approved quality of size 550 mm x 440 mm with 'P' or 'S' trap and embedding the closet with trap to shape in position with 40mm brick jelly lime concrete 1:2:5 etc., complete

25.European Water Closet (Colour) with 'P' or 'S' Trap with Double Flapped seat and seat cover with Brass Highes and 10 litre capacity PVC low level flusing tank with all internal fittings

26.Supplying and fixing of position of Indian make colour glazed earthwere wash basin 550mm x 400mm with all accessories such as cost Iron brackets, 32mm dia C.P. Waste coupling, Rubber plug and chain, 32mm dia 'B' class, G.I. Waste pipe, 15mm dia, G.M.Wheel valve, 15mm dia Nylon connection, 15mm dia Brass Nipples, 15mm C.P. pillar tap etc

27.Supplying and fixing of 1000 lits HDPE Water Tanks with suitable specials including cost of materials to site and all other labour charges.etc

28.Supply and delivery of Electric Mono set centrifugal pump conforming to IS 9079:2002 as amended from time to time, with CIFG 200 Casing, hydraulically and dynamically balanced Bronzegrade LTB-impeller, impeller ring and casing ring ,stainless steel shaft capable of discharging required quantity of water against atotal head noted below due to all causes. Pump shall of BEE 3 Star Rated and capable of discharging the specified quantity at the head noted at the minimum NPSHA at site conditions. The shutoff head shall beat least 25% over and above the head at duty point. The pump shall be suitable for operation in AC three phase, 415V+/-10%,50Hz+/- 5%. Squirrel cage induction motor for continuous operation. The speed of the Pump and Motor shall be not lessthan 2700 to 2900 RPM respectively. (100x20)

29.Supplu of Water supply pipes and specials with approved brand

110 mm dia PVC pipe 10KCS

63 mm dia PVC pipe 6 KCS

20 mm dia PVC pipe

25 mm dia PVC pipe

20 mm dia PVC Coupling

25 mm dia PVC Coupling

20 mm dia PVC Elbow

25 mm dia PVC Elbow

20 mm dia PVC Bend

25 mm dia PVC Bend

110 mm dia PVC Elbow

20 mm dia PVC Tee

25 mm dia PVC Tee

110 mm dia PVC Tee

30. Flooring with C.C. 1:3:6 mix using 40mm metal 100mm thick and top plastering with cement mortar 1:3 mix to 20mm thick

31.Manufacturing, Supplying and Fixing of Stainless Steel Hand rails for staircase using 50mm dia 304L Grade Stainless Steel pipe of 1.60mm thick at required locations to a height of 900mm from finished floor level welded to 38mm dia Stainless Steel pipe post of 1.00mm thick as vertical at 900mm centre with 2 Nos. of 25mm dia intermediate horizontal stainless steel pipe of 1.60mm thick in between. The vertical pipe has to be welded to the 100 X 100 X 6mm MS base plate encased in the base concrete. The rate is inclusive of the charges for cutting, bending, welding, grinding, polishing, conveyance, electrical charges, etc. complete

32.Provision for Drawing government logo,Awarness drawings and Quotes,lettering with base coat of primer etc complete including cost Paints of an approved brands and labour charges