PROVN OF SUBSTATION ROOM AND CHAIN LINK FENCING WITH GATE AT NAMS

Amount

Excavating in trenches n exc 1.5m wide and n exc 1.5m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10sqm on plan and n exc 1.5m in depth and getting out in any type of soil complete all as specified and directed.

M/L Cement concrete in foundations filling and mass concrete Type D2, 1:4:8 ( 40 mm graded aggregates ) complete all as specified and directed.

M/L for RCC 1:2:4 type B1 (20 mm graded stone aggregate) nominal mix in foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under reamed piles and mass concrete complete all as specified and directed.

M/L for RCC 1:2:4 type B1 (20 mm graded stone aggregate) nominal mix in columns,pillar,piers,post and struts complete all as directed.

M & L for mild steel TMT bar 10mm dia and over cut to length, bent to shape required inclduing cranking bending spirally, hooking ends and binding with and inclduing mild steel with (annealed) not less than 0.9mm dia complete all as specified and directed.

All as per item No. 5 here-in-above but 6-8 mm dia TMT bar in stirrups, spaces, binders nibs etc complete all as specified and directed.

Use and waste formwork to sides of concrete foundations, footings, bases of columns, raft and matt beams sides and soffits (if any) of foundation and plinth beams; and similar work ; vertical or to batter or flat complete all as specified and directed.

Use and waste forrnwork to sides of pillars. posts. struts. piers. columns and stan- chions for fair finished surfaces of concrete complete all as directed.

M/L rendering 05 mm thick on concrete walls in CM(1:4) finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 15mm thick cement plaster in CM 1:4 on fair / unfair faces of brick work and finishing the surface even and smooth (without using extra cement) etc. complete all as specified and directed.WPC shall be measured and paid separately

M&L granite 18-20 mm thick (table rubbed and polished) for wall in vertical in cement mortar (1:3) 12mm thick ,and pointing with white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

S/F framed work as in doors or gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering, Doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings, running rails and guides also fastening and fixing complete FE -410 Gde E-250 quality complete all as specified and directed. Refer drw No. CEJZ/STD-305/11.

S&F Rolled sections as in running rails ,wheel track and guides for sliding doors,fixed with angle cleats or other connecting plates complete all as specified and directed FE-410-W(Gde-E-250) quality-A complete all as specified and directed. Refer drw No. CEJZ/STD-305/11

M&L for cement concrete type B-0 1:2:4 using 12.5mm graded aggregate as in parapet and railings,coping and like including weathering,slightly rounded or chamfered angles and throating as directed complete all as specified and directed by Engr-In-charge.

M/L preparing new steel surfaces of any description exc 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zink chrome complete all as specified and directed. (JOB1 94.01SQM + JOB2 16SQM)

M&L for Fly ash Brick work with sub class 'B' old size brick straight or curved on plan exc 6m mean radius built in cement mortar 1:4 complete all as specified and directed.

Returning filling in the soil including spreading, levelling, watering and well ramming in layer n.exc 25cm thick each layer complete all as specified and directed.

Removing excavated soil to a distance not exc250m but n.exc 500 mtr away and depositing where directed at a level not exc 1.5m above the starting point complete all as specified and directed. (JOB1 27.60CUM + JOB2 22 CUM)

Excavation in post holes each n.exc 0.5 cum getting out, returning, filling in ramming earth or borken rubble mixed with earth around, in layers not exceeding 25 cm watering, and removing surplus soil to a distance n.exc 50m and making good complete in hard dense complete all as specified and directed.

S&F mild steel work in posts and struts in fencing including cutting tops to shape as directed, notching for wires etc, flat iron fillets ( for securing wire mesh etc) including all necessary drilling, bolting and rivetting etc conforming to FE-290 Gde E-165 complete all as specified and directed.

Fixing only Chain link fencing including line wires, any mesh, size & type to any type of standards, rails, straining blots, etc. including provision of binding wire complete all as specified and directed.

Supply only chain link fencing MS galvanised 100x100 mm ,3.15mm thick (approved by GE/EIC) including line wire,any mesh size ,type and fixing to angle iron post, rails including fixing with staining bolts to post/struts of specified length with nuts and washer, etc including provision of binding wire complete all as specified by Engr_in_Charge.

PCC 1:3:6 type C-2 ( using 40mm graded crushed stone aggregate) as in foundation, filling and mass concrete of post holes complete all as specified and directed.

S&F Mild steel round bars 10mm dia and over,cut to length,bent to shape required including cranking, bending spirally for hooping for columns,hooking ends and binding with and including mild steel wire(annealed)not less than 0.9mm dia or securing with clips or weld.complete FE-410-W(Gde E-250) quality A or Fe290(Gde-E-165) all as specified and directed.

S&F Galvanized 2 strand steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixijg to any type of std steel rails straining bolts including securing or tying at crossings with and provision of galvanized mild steel wire,staples or steel pins etc complete all as specified and directed.

S&F MS Screw bolts(machine made)with haxagonal or square heads at one end and screwed the other or screwed both ends each screwed to be fitted with washer and one haxagonal or square nut not exceeding 5cm long dia of shank 5 to 10mm.complete all as specified.

Surface Excavation n.exc 30 cm deep and averaging 15 cm deep in soft/loose soil and getting out complete all as specified and directed.

M&L for 100mm thick PCC 1:4:8 type D-2 20mm graded aggregate as in sub base to receive flooring complete all as specified and directed.

M&L for hardcore of broken stone or boulders of gauge exc 63mm but n.exc 100 mm,deposited,spread,levelled in layers n.exc 15cm thick ,watered,rolled and rammed to a true surface complete all as specified and directed.

M&L for 100mm thick cement concrete Type B-1,1:2:4 using 20mm graded aggregates as in flooring including finishing the surface even and smooth without using extra cement complete all as specified and directed.

M&L for forming contraction(dummy) joint 65mm deepx10mm wide,filled with grade'A' sealing compound complete all as specified and directed.

M&L for two coat of camouflaging APEX paint on new plastered/ unplastered surfaces of walls, pillers,cornices by brooming down or steel wire brushing, scraping down, moulds, moss and efflorescence salts and oil and greasy spots of old painted surfaces including edges using necessary fillng compound of ALTEK putty to obtain smooth finish using sand paper and necessary repair with putty complete all as specified and directed.

Earthwork in excavation by mechanical means in any kind of soil by (Hydraulic excavator)/ in foundation trenches or drains(n.exc 1.5 mtr wide) ,including dressing of sides and ramming of bottoms,lift upto 1.5 mtr,including getting out the excavated soil and disposal of surplus excavated soil as directed,within a lead of 50mtr complete all as specified and directed.

M&L for filling loose soil free from vegetation,pebbles and compacting,ramming in layers with true level complete all as specified and directed by Engg-in-charge. Note:- Soil to be brought outside from MOD land. Contractor has to arrange his own transport T&P etc and cost of all is deemed to be inclusive in quoted rates. Nothing extra shall be paid by deptt.

M & L for formwork to soffits of suspended slabs such as roof slabs, floor slabs, landings and similar work for rough finished surface, not exceeding 200mm thick (Horizontal or sloping) and complete all as specified.

Use and waste of form work to edges of concrete flats, slabs etc incl fair finished surface all as specifed and directed.

M & L for formwork to sides and soffits of floor or roof beam, lintel beams flat surface etc incl supports, overhangs etc complete all as specified.

M & L for formwork to chajjas and similar items, flat surface incl edges complete all as specified.

M & L for reinforced cement concrete M-20 using (20mm graded aggregate) in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified.

M & L for reinforced cement concrete M-20 using (20mm graded aggregate) in roof beams, cantilevers, bressummers, lintels over 1.5m span and complete all as specified.

M & L for reinforced cement concrete M-20 (using 20 mm graded stone aggregate) in Chajjas and the like complete all as specified and as directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tiles exceed.0.06 sqm but not exc.0 .11sqm , in floors etc laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed.

M&L non skid ceramic coloured tiles 7 to 8 mm thick (square/ rectengular) area of each tiles exceed 0.11 sqm but not exc.0.18sqm , in floors etc laid over 15mm thick screed bed in cement mortar 1:6 and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed.

M&L Glazed ceramic Coloured tiles 450x300/7-8 mm thick, on vertical surfaces such as skirting, dados and risers to steps etc.laid over 10mm thick backing coat in cement mortar 1:4 and jointed in neat cement slurry and pointed in white or Coloured cement to match complete all as specified and directed..

M&L for Fly ash Brick work , straight or curved on plan to any radius in half brick thick walls built in cement mortar 1:4 complete all as specified and directed.

Material and labour for 15mm thick cement plaster in CM (1:6) on fair faces of brick or concrete surfaces and finishing the surface even and smooth (without using extra cement) etc. complete all as specified and directed.

Material and labour for 10 mm thick cement plaster in CM (1:3) on concrete surfaces of ceiling and finishing the surface even and smooth (without using extra cement) etc Complete all as specified.

M&L for preparing newly plastered surfaces of ceilings, soffits & chajja and applying three coats of white wash complete all as spd and directed.

M&L for preparation of newly plastered wall surfaces and applying two coats of oil bound distemper over alkali resistance primer complete all as specified and as directed.

Material and Labour for preparation of new plastered surfaces and applying two coats of cement base paint on wall complete all as specified.

M&L for box type steel window 1.25 mm thick made of ERW tube P-Section of size 60 x 25 mm double rebated outer frame comprise of glazed skeleton shutter(two gauged shutters and two glazed shutter) of ERW tube P-Section size 50 x 20 mm and 1mm thick one/two Nos openable leaf consisting of two Nos sash bar of T-Section 20x3mm welded to frame with one No Vertical mullion of ERW box type T-Section of size 60 x 25 mm and 1.25 mm thick and FI 2 mm thick welded / screwed to frame for fixing of glass including fittings and fixture like Handle, Tower Bolt, stopper, cleat, pintal hinges, hold fast etc. (i) Hold Fast, 150mm long of 120mm x 3 mm made to shape -04 Nos per window. (ii) Handle of Z sec 20mm x 25mm, 100 mm long -1 No per leaf (iii) MS Tower bolt 150mm long - 2 No per leaf (iv) Z Sec 20mm x 25 mm, 100 mm long stopper - 1 No per leaf (v) Cleat 55 mm long of hollow square 15mm x 20mm x.63mm welded to hinge -1 No per leaf. (vi) MS Pintal hinges of size 75mm x 12mm - 2 Nos per leaf . (vii) 10 mm square guard bar, 10 cm centre to centre. (viii) 25x4 mm flat iron all around for joint of both frame. Note : Incl taking down old steel / wooden window and making good dismantled portion with PCC 1:2:4 type B0 incl hold fast PCC (four No’s for Each window) & around required plaster in CM 1:4 and match with existing finishing complete all as specified and directed.

S & F in repair mild steel box type ventilator fixed type with glazing bar with mesh & glass as per drg No. CEJZ/TD-06/07 dt 07.06.07 incl 12mm square guard bar 10cm c/c and two coat of synthetic enamel paint over one cost of primer complete including taking down of old ventilator complete all as specified and directed. all as specified and directed.

Supply and fixing 3mm thick figured glass pin head type and glazing with oil putty in squares not exc 0.50sqm in each pane complete all as specified and dircted.

Supply & fixing 3mm thick sheet glass ordinary quality glazing with oil putty in square n exc 0.5 sqm quality or description from steel frame and all specified.

S&F for 35mm thick flush shutters, solid core construction, with particle board core and plywood face panels, commercial type on both sides and one face is covered with decorative face veneer with lipping/frame to match incl two coat of synthetic enamel paint over a coat of pinc primer on wooden surface complete all as spd and directed by Engr-in-charge.

S & F 35 mm thick Second class hard wood Glazed and skeleton shutters, open rebated and prepared to receive glass, gauze, etc., divided in to squares with plain, chamfered or rounded mitred and rebated sash bars any numbers, edges of framing plain, chamfered complete all as specified and directed.

Supplying and fixing factory made Solid PVC Moulded Door shutter with wood free EPS,28-30mm thick (stiles),with 2 or 4 raised panel design with 2mm thick moulded PVC sheet on the front face & 2mm Plain colour PVC sheet on back face,supplying & fixing in frame at site as per specification & drawing complete all as specified and directed by Engr-In-Charge

S &F Stainless steel wire cloth, 0.36mm nominal dia of wire and average width of aperture 1.40mm and fixed with stainless steel wire staples complete all as specified and directed.

S&F 100mm long cold rolled mild steel medium weight butt hinges welded or screwed to steel, aluminium and wooden chowkhat complete all as specified and directed.

S&F Floor door stopper of Aluminium alloy body and at edge with rubber bush of 150 mm long fixed on with necessary steel screw complete all as specified and directed.

S&F of 150mm long Aluminium anodised, barrel tower bolts of extruded section fixed complete all as specified and directed.

S&F of 150mm in size extruded aluminium alloy handles, fabricated type, anodised and fixed complete all as specified and directed.

S & F 250 mm long Aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast Aluminium alloy complete all as specified and directed.

M&L for applying two coat of undiluted thick water based UV resistant elastorneric Polyurethane liquid membrane with UV resistance properties and solar refelctive properties of 109 over one coat of primer (1:3, Dilution:water) Note: Every each coat interval between 6 hrs,having solid content more than 80% and elastic recovery @150% elongation %---70 to 75 . complete all as specified and directed.

M&L for two coats of synthetic enamel paint over a coat of pink primer to new wooden surfaces of any description over 10cm width or girth including preparation of new surfaces complete all as specified and directed.

S&F PVC 10 litres, valveless. Syphonic action type, flushing cistern, low level, with inlet, ball valve, float, and handle and brackets including flush pipe of polyethylene of high density PVC, 32 mm dia for low level cistern complete all as specified

S&F PVC connections 15mm size with PTMT nuts of length 450mm complete all as spd(minium weight of190gms) complete all as specified and directed

Supply and fixing bib tap long body fancy type 15mm dia chromium plated fancy type with crutch or butterfly handle, screwed down, screwed for iron pipe or for brass ferrule complete all as specified and directed.

S&F 15mm bore stop cock concealed long shank chromium plated fancy type screwed down high pressure with crutch or butter fly handle

S&F angle cock fancy type cast copper alloy chromium plated screwed down high pressure with capstan head screwed for iron pipe 15 mm bore complete complete all as specified and directed.

Supply & fixing vitreous china wash down water closet pan (padestal pattern) white with flush pipe for low level flushing cistern including plastic water closet seat white with jet, closed pattern with flat bottom and cover and mild steel chromium plated or aluminized hinging device complete and directed.

S & F 15 mm chromium plated shower rose 150 mm x150 mm in square size with or without swivel joints, any size, including square tubular shower arms of necessary fixing to steel pipe or union complete all as specified and directed

S&F brass chromium plated tubular towel rail,20mm dia,D-type 60 cm long between flanges all as specified and directed.

S&F 500 ltr capacity rotational moulded polyetheylene water storage tanks (cylingrical verticlal with closed top) hoisted and fixed in position incl 20mm bore ball valve PVC high pressure with polythene float valve complete all as specified and directed.

Supply and fixing 100mm dia cast iron spun soil waste and vent pipe in any length with or without ear with cement joint laid in trenches or in floor complete with clamps all specified and directed.

Supplying and fixing cast iron spun soil, waste and vent pipe in any length 75 mm bore of pipe with or without ears with cement joint fixed to walls complete with clamps incuding suitable clamps and access doors complete all as specified.

Supply and fixing CI bend 100mm bore (in any radius ) diminishing pices or tapers (larger bore measured) complete all as specified.

S & F cast iron cast Cowls 75 mm Dia eqal & unequal fixed lead joint complete all as specified and directed.

Supply and fixing cast iron floor trap 100mm outer dia, with grating including jointing to waste pipe fixed in cement concrete (1:2:4) type B-1 complete all as specified.

Material and labour for PCC 1:4:8 type D-2(using 40mm graded crushed stone aggregates)for bed of sewage lines including packing under and haunching against the sides of pipe after they are laid and tested complete all as specified and directed.

S&F PVC (SRW) pipe 110 mm waste pipe single socketed in any length with rubber ring joints,fixed to walls or laid in trenches etc complete all as specified and directed.Make-Finolex/supreme and all other equivalent makes as specified in Appendix'B'.

M&L, kota stone slab as in flooring,skirting etc 20 to 25 mm thick over cement screed base laid on 15 mm thick CM 1:6 and jointed with grey cement slurry mixed with pigment to match the shade of the slab incl rubbing and polishing incl chamfering edge complete all as specified and directed by Engr-in-Charge.

S&F CP Grating125mm dia with or without hole as per site requirement fixed complete with filling of white cement all around complete all as specified.

S & F 15 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed

S & F 20 mm bore Galvanized Steel tubes, medium grade for flush pipes, water supply pipes etc., fixed to walls and ceilings or laid in floors complete all as specified and directed

Supplying and fixing 15mm bore Pillar Cock swan NECK for wash basin cast copper alloy chromium plated screwed down high pressure screwed for iron pipe complete of approved make as per sample all as specified and directed.

S&F Vitreous china wash hand basin white flat back size 550x400mm including brass waste coupling, PVC waste pipe and plug and porcelain stopper brackets of angle 35x35x5mm and cutting for and pinning in ends of brackets or erecting stand fixed complete all as specified and directed.

S&F 20 mm bore dia gate valve,gun metal with iron wheel head,screwed both ends and fixed all as specified and directed.

Supply and fixing PVC waste pipe 32/38/40mm dia, 600 to 750mm long complete all as specified. Make:(Prayag,Shakti,Polytuf)

S&F 1.25 mm thick Steel rolling shutters, partly ventilated in the middle (honey comb) with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of primer; erected in position as indicated, complete: push pull or manual type complete all as specified and directed by Engr-In-charge

S&F safety lever locks mild steel with levers for rolling shutter complete all as specified and directed.

M&L for Precast RCC (1:2:4) type B-1 using 20mm graded stone aggregate set in cement mortar 1:6 as in landings, cover slabs for manhole etc, water tank base and similar work complete all as specified and directed.

Material & labour for 50 mm thick PCC (1:3:6) type C-2 (using 20 mm graded stone aggegate) as in plinth protection finished the surfaces even and smooth without using extra cement complete all as specified and directed.

S & F for HIP RATRO radium sheet / tape on stainless steel frame (size of board / samples of letter / pictures / writing will be provided by Engineer-in-charge and of best quality as approved by GE, incl dismantling existing old vintage damaged standing sign board complete all as specified and directed.

S&F for 3mm thick Aluminium Composite panel sheet best quality as per make in PS Clause complete all as specified and directed.

M&L for glow sign board frame / standing sign board made out of stainless steel tubular / flat / angle as in any size ,dia and stainless steel of grade A-ISI 304(1818) complete all as spd and directed

S&F decorative stainless steel dome 65mm to 75mm dia complete all as spd and directed.

M&L for machine pressed precast concrete interlocking paver block any shape and size and colour alternate red and yellow conforming to IS-15658-2006 of 80 mm thickness with grey cement and no pigment complete all as specified and directed.

M&L for sand filling under floors or in foundation including watering and consolidation complete all as specified and directed.

M&L for treating the bottom and sides of excavation at the rate of 5 litres of emulsion per Sqm of Surface area complete all as specified and directed.

M&L for treating the top surface of filled earth at the rate of 5 litres of emulsion per Sqm of surface area complete all as specified and directed.

M&L for point wiring For one light /fan/ buzzer point controlled by one 5 Amp switch one way with 1.5 sqmm (Nominal area ) 1100 Volt PVC Insulated , FRLS unsheathed and multi stranded copper conductor cable in and including new PVC Concealed conduit not less than 20mm dia 1.5mm thick for one light / fan point or bell point controlled by one switch (including cutting chases and making good the distributed surfaces) and fixing new 3mm thick hylem sheet top cover, sheet screws and 1.6mm thick GI sunken boxes after removing old unserviceable plastic laminated sheeet and sunken boxes included 1.5 Sqmm stranded copper conductor with green PVC Insulation earth contunity conductor connected to common earth dolly etc . complete all as specified and directed for the following :- Note : The cost of sunken boxes and bakellite sheet is included in the quoted rate)

All as per srl item No. 103 here in before but For one three pin socket outlet 5 Amps independent board complete all as specified and as directed.

All as per srl item No. 103 here in before but For one three pin 5 Amps socket outlet on the same board with other switches complete all as specified and as directed.

All as per srl item No. 103 here in before but with 2.5 Sq mm size cable multi stranded FRLS copper wire unsheathed for one 3 pin socket outlet 15 Amps on independent board including continuous earth wire of PVC insulated 1.5 Sq mm copper solid conductor connecting to common earth dolly complete all as specified and as directed.

Supply and Fixing of switch piano type 6 Amps one way 230 volts AC complete all as specified and as directed

Supply and Fixing of socket outlet 5 pin, 6 Amps flush type 230 volts AC complete all as specified and as directed

Supply and Fixing of switch piano 16 Amps type one way 230 volts AC complete all as specified and as directed

Supply and Fixing of socket outlet 6 pin 6/16 Amps multi purpose flush type 230 volts AC complete all as specified and as directed

Supply and fixing of ceiling rose 65X50 mm two to three terminals complete all as specified.

Supply and Fixing of fan regulator, electronic step socket type heavy duty 230 volts complete all as specified and as directed.

S&F of sheet steel enclouser distribution boards, double door factory made 3 phase 415 volts 4 way with 200 amps rating copper bus bar and PVC insulated copper jumpers of suitable size from the MCCB to the out going circuits one incoming MCCB and 12 outgoing MCBs circuits comprising of 3 phase 4 wire of suitable rating complete all as spcd and directed with the following accessories :-( For out going MCB measured and paid separately) MCCB 100 amps, 25 KA, TP, 415 volts, 50 Hz = 01 No.

Supply and fixing of MCB single pole 6 to 32 Amps all as specified and directed

M&L for earthing complete with galvanised steel earth plate electrode of size 600 mm x 600 mm x 6 mm thick buried directly in ground (earth pit not less than 2.25 mtr deep below normal ground level) with top edge of the plate not less than 1.5 mtr below ground level, connected to galvanized earth lead wire 4.00 mm dia by means of bolts nuts check nuts & washers of galvanized iron or steel , procteded by GI pipe 15 mm bore( light grade) and watering pipe 20 mm bore GI pipe (light grade ) and chamber of pcc 1:4:8 type D2 using 40 mm graded stone aggregate and coping shall be in PCC 1:3:6 type C1 using 20mm graded stone agg. 50 mm thick cover of RCC 1:2:4 type B1 using 20 mm graded stone agg. reinforced with 8 mm dia MS tor bar @ 80 mm c/c both ways including excvation and earth work and removal of surplus soil complete all as shown in electrical plate no 5 of SSR PT 1, 1991 with charcoal dust and salt complete and earth lead connected to earthing test point (up to main switche, DBs) complete all as specified & testing on completion.

Supply & fix of LED Street Light Luminaire 35 watt 6000K with .high power LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,powder coated pressure die cast aluminium with heat resistant toughened glass with lens complete all as specified and as directed.

Supply and fixing of LED T-8 tube light fitting with single side connection LED tube rod 18/20W 4 feet 1 x 18/20 watt MS CRCA box type including rotary type bipin holder and connection with PVC insulalted twin core 23/0.0076 twisted copper cable from ceiling rose to tube light fitting complete all as specified and directed.

Supply and fix ceiling fan complete with blades, down rods, and accessories, 230V , 1200 mm sweep min air delievry 210 CFM with service value 6.0 BEE five star rated with brushless direct current motor (BLDC ) complete all as specified and as directed.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 300 mm sweep, metallic body complete with louvrers and shutters including electric connection with pvc flexible twin core copper wire from ceilingrose to Exhaust fan, nut & bolt complete all as specified and as directed. Make:- makes as specified in Appendix 'B'.

Supply and fixing Single phase propeller type ventilating ( Exhaust fan) heavy duty AC 230 volts 450 mm sweep, metallic body complete with louvrers and shutters including electric connection with pvc flexible twin core copper wire from ceilingrose to Exhaust fan, nut & bolt complete all as specified and as directed. Make:- makes as specified in Appendix 'B'.

Supply and laying or fixing 1100 Volts grade heavy duty cable with PVC insulated aluminium standard conductor served with an inner sheathing of PVC tape and over all PVC Sheathed in service connections one twin core 6 Sqmm cable standard conductor cable flat or circular all as specified and directed by Engineer- in- Charge.

Supply & Fixing flood Light Luminaire 120 watt with .high power SMD LED cool white,CRI 75,+/- 5% supply voltage 220/240/50 Hz, light engine driver base.pole adapter,pressure die cast LM6 diffusor:injection model polycarbonate,powdre coated in IP 66 Incliding protection over temperature should be from the same manufacturer Product complete all as specified and directed.

Supply and Install of Off Load Change over switch 415 Volts in sheet metal enclouser 4 Pole of capacity minimum 63 Amps complete all as specified and directed.

Supply & fixing of integral post top lanterns complete with Black ABC plastic spigot, spun aluminium funnel shape with clear acrylic cover light opening on canopy with baffles and accessories with 10watt LED lamp complete all as specified and directed

Supply and fixing bracket made out of GI pipe 50/ 40 mm medium grade 1.2 mtr long made to shape with fixing clamps of MS flat 40x6mm nut bolts etc for security light all as specified and directed

M&L for two single core sub main wiring 4 Sqmm multi-strand PVC insulated FRLS copper conductor cable including PVC insulated copper conductor cable of size 2.5 Sqmm as cotinuous earth wire connecting to common earth including connections of cable with MCBs or bus bars complete all as specified and directed

Supply and fixing geyser 25 Ltrs capacity , after connecting electric and water connection and screwing nut and bolts to fixed on wall and make surface good complete all as specified and directed.

Supply and fixing of sheet metal enclosure with metal clad socket and plug top complete with MCB SP 20A all as specified and directed

B.J.CONSTRUCTION CO

ESS KAY BUILDER

M/s AKG Engineers & Contractors

tarlok singh contractor

M/s MAHAJAN CONSTRUCTION CO.