Loading…
Loading…
Tender Value
₹1.2 Cr
EMD Value
₹2.4 L
Closing Date
25 Sept 2026, 12:00 pm
No
No
Single Packet System
Normal Tender
No
Not Applicable
Lowest to Highest
60 days
Expenditure
Capital (Works)
Above/Below/Par
TENDER
15 conditions · 4 needing a document upload
The tenderer must have minimum average annual contractual turnover of V/N or 'V' whichever is less; where V= Advertised value of the tender in crores of Rupees N= Number of years prescribed for completion of work for which bids have been invited. The average annual contractual turnover shall be calculated as an average of "total contractual payments" in the previous three financial years, as per the audited balance sheet. However, in case balance sheet of the previous year is yet to be prepared/ audited, the audited balance sheet of the fourth previous year shall be considered for calculating average annual contractual turnover. The tenderers shall submit requisite information as per Annexure-VIB, along with copies of Audited Balance Sheets duly certified by the Chartered Accountant/ Certificate from Chartered Accountant duly supported by Audited Balance Sheet. The balance sheet and all other financial documents attested /certified by CA's to substantiate fulfilment of financial Eligibility Criteria should be with UDIN, failing which the offer is likely to be rejected without any further reference.
Must have valid Electrical Contractors license issued by Central Govt./any State Govt. valid throughout the contract period.
Must have valid Electrical Supervisor's certificate issued by Central Govt./any State Govt. valid throughout the contract period. Supervisor should be qualified for HT (11KV) voltage work. Name of the supervisor should be endorsed in Electrical contractor License. If the firm deploys supervisor other than endorsed in the contractor license valid employment documents should be uploaded.
The tenderer must have successfully completed or substantially completed any one of the following categories of work(s) during last 07 (seven) years, ending last day of month previous to the one in which tender is invited:(i) Three similar works each costing not less than the amount equal to 30% of advertised value of the tender, or (ii) Two similar works each costing not less than the amount equal to 40% of advertised value of the tender, or (iii) One similar work costing not less than the amount equal to 60% of advertised value of the tender. Similar nature of work for this work is defined as "Supply, installation, testing and commissioning of HT panels/LT panels, cable laying, wiring/rewiring of any building/office in Central Government or State Government or Public Sector Understandings ( also called Public Sector Enterprise)." for participating in the works tender proposed above.
63 conditions · 6 needing a document upload
GST implemented from 1st july'2017. All the bidder should attach GST registration certificate, Tenderer has to fulfill GST Compliance as per Govt. norms. GST will levied as per instruction circulated time to time.
Tenderers are required to upload their Permanent Account Number (PAN) card.
Declaration of proprietorship/partnership firm and necessary document should be submitted along with tender.
Mandate form should be uploaded as per attached format.
Employment/Partnership etc. of Retired Railway Employees: (a) Should a tenderer i) be a retired Engineer of the gazetted rank or any other gazetted officer working before his retirement, whether in the executive or administrative capacity or whether holding a pensionable post or not, in the Engineering or any other department of any of the railways owned and administered by the President of India for the time being, OR ii) being partnership firm / joint venture (JV) / registered society / registered trust etc have as one of its partners a retired Engineer of the gazetted rank or any other gazetted officer working before his retirement, OR iii) being an incorporated company have any such retired Engineer of the gazetted rank or any other gazetted officer working before his retirement as one of its directors AND in case where such Engineer or officer had not retired from government service at least 1 year prior to the date of submission of the tender THEN the tenderer will give full information as to the date of retirement of such Engineer or gazetted officer from the said service and as to whether permission for taking such contract, or if the Contractor be a partnership firm or an incorporated company, to become a partner or director as the case may be, has been obtained by the tenderer or the Engineer or officer, as the case may be from the President of India or any officer, duly authorized by him in this behalf, shall be clearly stated in writing at the time of submitting the tender. b) In case, upon successful award of contract, should a tenderer depute for execution of the works under or to deal matters related with this contract, any retired Engineer of gazette rank or retired gazetted officer working before his retirement in the Engineering or any other department of any of the railways owned and administered by the President of India for the time being, and now in his employment, then the tenderer will ensure that retired Engineer or retired gazetted officer had retired from government service at least 1 year prior to the date of his employment with tenderer and in case he had retired from service within a year then he possesses the requisite permission from the President of India or any officer, duly authorized by him in this behalf, to get associated with the tenderer. c) Should a tenderer or Contractor being an individual, have member(s) of his family or in the case of partnership firm/ company / joint venture (JV) / registered society / registered trust etc. one or more of his partner(s)/shareholder(s) or member(s) of the family of partner(s)/shareholder(s) having share of more than 1% in the tendering entity employed in gazetted capacity in the Engineering or any other department of the railway, then the tenderer at the time of submission of tender, will inform the authority inviting tenders the details of such persons. Note:-If information as required as per 16.a), b), c) above has not been furnished, contract is liable to be dealt in accordance with provision of clause 62 of Standard General Condition of contract. Format for declaration in this regard is attached with the tender document.
Work experience certificate from private individual shall not be considered. However, in addition to work experience certificates issued by any Govt. Organisation, work experience certificate issued by Public listed company having average annual turnover of Rs 500 crore and above in last 3 financial years excluding the current financial year, listed on National Stock Exchange or Bombay Stock Exchange, incorporated/registered at least 5 years prior to the date of closing of tender, shall also be considered provided the work experience certificate has been issued by a person authorized by the Public listed company to issue such certificates.
In case tenderer submits work experience certificate issued by public listed company, the tenderer shall also submit along with work experience certificate, the relevant copy of work order, bill of quantities, bill wise details of payment received duly certified by Chartered Accountant, TDS certificates for all payments received and copy of final/last bill paid by company in support of above work experience certificate.
The bidder shall submit duly filled Tender Form(Annexure-I) of GCC-2022 updated upto latest correction slip..
Please enter the percentage of local content in the material being offered. Please enter 0 for fully imported items, and 100 for fully indigenous items. The definition and calculation of local content shall be in accordance with the Make in India policy as incorporated in the tender conditions.
Inspection of material is to be done by RITES. Inspection charges of RITES are to be borne by the contractor where necessary as per extant rule (Where the value of purchase order exceeds Rs.5.0 Lakhs).
Guarantee period for the overall work will be 12 (Twelve) months from the date of completion of the work. Any defects, if arises during the guarantee period contractor will be responsible to rectify or replace as the case may be at the discretion of the Railway Administration. Security deposit will be refunded/ released after successful completion of the guarantee period. Also, contractor has to ensure proper functioning of the items covered under specific warranty/guarantee as mentioned in Tender Documents during that period (Warranty/guarantee period will be calculated from the date of commissioning).
Online Payment:- The detailed payment transaction particulars should be attached as attachment.
If the tenderers deliberately gives/give wrong information in his/their tender or creates/create circumstances for the acceptance of his/their tender, the Railway reserves the right to reject such tender at any stage.
The tenderers shall keep the offer open for a minimum period as mentioned in NIT from the date of opening of the tender, within which period the tenderers can not withdraw their offer, subject to the period being extended further if required, by mutual agreement from time to time. Any intervention of the above condition will make the tenderer liable for forfeiture of his security deposit for due performance of the foregoing stipulation.
It shall not be obligatory on the said authority to accept the lowest tender or any other tender, and tenderer(s) shall neither demand any explanation for the cause of rejection of his/ their tender nor the Railway to assign reasons for declining to consider or reject any particular tender or tenders.
If any partner(s) of a partnership firm expires after the submission of its tender or after the acceptance of its tender, the Railway shall deem such tender as cancelled/contract as terminated under clause 61 of the Standard General Conditions of Contract, unless the firm retains its character as per partnership agreement. If a sole proprietor expires after the submission of tender or after the acceptance of tender, the Railway shall deem such tender as cancelled / contract as terminated under clause 61 of the Standard General Conditions of Contract.
Bid Security: (1) (a) The tenderer shall be required to submit the Bid Security with the tender for the due performance with the stipulation to keep the offer open till such date as specified in the tender, under the conditions of tender. The Bid Security shall be as under: Value of the Work and Bid Security : For all works, 2% of the estimated cost of the work. Note: (i) The Bid Security shall be rounded off to the nearest 100. This Bid Security shall be applicable for all modes of tendering. (ii) Any firm recognized by Department of Industrial Policy and Promotion (DIPP) as 'Startups' shall be exempted from payment of Bid Security detailed above. (iii) Labour Cooperative Societies shall submit only 50% of above Bid Security detailed above. (b) It shall be understood that the tender documents have been issued to the tenderer and the tenderer is permitted to tender in consideration of stipulation on his part, that after submitting his tender he will not resile from his offer or modify the terms and conditions thereof in a manner not acceptable to the Engineer. Should the tenderer fail to observe or comply with the said stipulation, the aforesaid amount shall be liable to be forfeited to the Railway. (c) If his tender is accepted, this Bid Security mentioned in sub para (a) above will be retained as part security for the due and faithful fulfillment of the contract in terms of Clause 16 of the Standard General Conditions of Contract. The Bid Security of other Tenderers shall, save as herein before provided, be returned to them, but the Railway shall not be responsible for any loss or depreciation that may happen thereto while in their possession, nor be liable to pay interest thereon.
The Bid Security shall be deposited either in cash through e- payment gateway or submitted as Bank Guarantee bond from a scheduled commercial bank of India or as mentioned in tender documents. The Bank Guarantee bond shall be as per Annexure- VIA and shall be valid for a period of 90days beyond the bid validity period. In case, submission of Bid Security in the form of Bank Guarantee, following shall be ensured: i. A scanned copy of the Bank Guarantee shall be uploaded on e-Procurement Portal (IREPS) while applying to the tender. ii. The original Bank Guarantee should be delivered in person to the official nominated as indicated in the tender document before closing date for submission of bids (Le. excluding the last date of submission of bids) . iii. Non submission of scanned copy of Bank Guarantee with the bid on e-tendering portal (IREPS) and/or non submission of original Bank Guarantee within the specified period shall lead to summary rejection of bid. iv. The Tender Security shall remain valid for a period of 90 days beyond the validity period for the Tender. v. The details of the BG, physically submitted should match with the details available in the scanned copy and the data entered during bid submission time, failing which the bid will be rejected vi. The Bank Guarantee shall be placed in an envelope, which shall be sealed. The envelope shall clearly bear the identification "Bid for the ***** Project" and shall clearly indicate the name and address of the Bidder. In addition, the Bid Due Date should be indicated on the right hand top corner of the envelope. vii. The envelope shall be addressed to the officer and address as mentioned in the tender document. viii. If the envelope is not sealed and marked as instructed above, the Railway assumes no responsibility for the misplacement or premature opening of the contents of the Bid submitted and consequent losses, if any, suffered by the Bidder.
The successful bidder shall submit the Performance Guarantee (PG) in any of the following forms, amounting to 5% of the original contract value and Additional Performance Guarantee as per Clause 16(4)(h) of GCC-2022, in any of the following forms:- (i) A deposit of Cash; (ii) Irrevocable Bank Guarantee; (iii)Government Securities including State Loan Bonds at 5% below the market value; (iv) Pay Orders and Demand Drafts tendered by any Scheduled Commercial Bank of India; (v) Guarantee Bonds executed or Deposits Receipts tendered by any Scheduled Commercial Bank of India; (vi) Deposit in the Post Office Saving Bank; (vii) Deposit in the National Savings Certificates; (viii) Twelve years National Defence Certificates; (ix) Ten years Defence Deposits; (x) National Defence Bonds and (xi) Unit Trust Certificates at 5% below market value or at the face value whichever is less. Also, FDR in favour of FA&CAO (free from any encumbrance) may be accepted. New Para 16(4) (h) of Part-II of GCC'22: If a tender is accepted on the quoted rates of bidder which is below the advertised tender value, an additional performance security shall be submitted by the bidder as below: (i) If Bid quoted in % of advertised cost is Below 0 - 5% (inclusive), Additional Performance Guarantee (%) will be 'Nil'. (ii) If Bid quoted in % of advertised cost is Below 5%, Additional Performance Guarantee (%) will be '5%'.
Performance Guarantee : The successful bidder shall have to submit a Performance Guarantee (PG) within 21 (Twenty one) days from the date of issue of Letter of Acceptance (LOA). Extension of time for submission of PG beyond 21 (Twenty one) days and upto 60 days from the date of issue of LOA may be given by the Authority who is competent to sign the contract agreement. However, a penal interest of 12% per annum shall be charged for the delay beyond 21(Twenty one) days, i.e. from 22ndday after the date of issue of LOA. Further, if the 60thday happens to be a declared holiday in the concerned office of the Railway, submission of PG can be accepted on the next working day. In all other cases, if the Contractor fails to submit the requisite PG even after 60 days from the date of issue of LOA, the contract is liable to be terminated. In case contract is terminated railway shall be entitled to forfeit Bid Security and other dues payable to the contractor against that particular contract, subject to maximum of PG amount. In case a tenderer has not submitted Bid Security on the strength of their registration as a Startup recognized by Department of Industrial Policy and Promotion (DIPP) under Ministry of Commerce and Industry, DIPP shall be informed to this effect. The failed Contractor shall be debarred from participating in re-tender for that work. However the clause may also applicable as amended time to time.
The Performance Guarantee shall be submitted by the successful bidder after the Letter of Acceptance (LOA) has been issued, but before signing of the contract agreement. This P.G. shall be initially valid upto the stipulated date of completion plus 60 days beyond that. In case, the time for completion of work gets extended, the Contractor shall get the validity of P.G. extended to cover such extended time for completion of work plus 60 days.
The value of PG to be submitted by the Contractor is based on original contract value and shall not change due to subsequent variation(s) in the original contract value.
The Performance Guarantee (PG) shall be released after physical completion of the work based on 'Completion Certificate' issued by the competent authority stating that the Contractor has completed the work in all respects satisfactorily. The Security Deposit shall, however, be released only after expiry of the maintenance period and after passing the final bill based on No Claim Certificate from the contractor.
Whenever the contract is rescinded, the Security Deposit shall be forfeited and the Performance Guarantee shall be encashed. The balance work shall begot done independently without risk cost of the failed contractor. The failed contractor shall be debarred from participating in the tender for executing the balance work. If the failed contractor is a JV or a Partnership firm,then every member/partner of such a firm shall be debarred from participating in the tender for the balance work in his/her individual capacity or as a partner of any other JV/partnership firm.
(i) Unless otherwise specified in the special conditions of the contract, the accepted variation in quantity of each individual item of the contract would be upto 25% of the quantity originally contracted, except in case of foundation work (in which no variation limit shall apply). However, the rates for the increased quantities shall be as per sub- para (iii) below. (ii) The Contractor shall be bound to carry out the work at the agreed rates and shall not be entitled to any claim or any compensation whatsoever upto the limit of 25% variation in quantity of individual item of works. (iii) In case an increase in quantity of an individual item by more than 25% of the agreement quantity is considered unavoidable, then same shall be executed at following rates a. Quantities operated in excess of 125% but upto 140% of the agreement quantity of the concerned item, shall be paid at 98% of the rate awarded for that item in that particular tender; b. Quantities operated in excess of 140% but upto 150% of the agreement quantity of the concerned item shall be paid at 96% of the rate awarded for that item in that particular tender; c. Variation in quantities of individual items beyond 150% will be avoided and would be permitted only in exceptional unavoidable circumstances and shall be paid at 96% of the rate awarded for that item in that particular tender. d. Variation to quantities of Minor Value Item: The limit for varying quantities for minor value items shall be 100% (as against 25% prescribed for other items). A minor value item for this purpose is defined as an item whose original agreement value is less than 1 % of the total original contract value. d.(i) Quantities operated upto and including 100% of the agreement quantity of the concerned minor value item, shall be paid at the rate awarded for that item in that particular tender; d.(ii) Quantities operated in excess of 100% but upto 200% of the agreement quantity of the concerned minor value item, shall be paid at 98% of the rate awarded for that item in that particular tender; d.(iii) Variation in quantities of individual minor value item beyond 200% will be avoided and would be permitted only in exceptional unavoidable circumstances and shall be paid at 96% of the rate awarded for that item in that particular tender. (iv) In case of earthwork items, the variation limit of 25% shall apply to the gross quantity of earthwork items and variation in the quantities of individual classifications of soil shall not be subject to this limit. (v) As far as Standard Schedule of Rates (SSOR) items are concerned, the variation limit of 25% would apply to the value of SSOR schedule(s) as a whole and not on individual SSOR items. However, in case of Non Standard Schedule of Rates (SSOR) items, the limit of 25% would apply on GCC April 2022 65 the individual items irrespective of the manner of quoting the rate (single percentage rate or individual item rate).
For settlements of disputes Arbitration provision of relevant clauses of S.E.Railway Standard General Conditions of contract of 2022 with up to date correction slip will be followed. Tenderer should comply with all the provisions with respect to labour given in this tender document, IR Standard General Condition Of Contract 2022 updated with correction slips Issued up to date, relevant statues of government w.r.t labour laws.
The Railway reserves the right of not to invite tenders for any of Railway work or works or to invite open or limited tenders and when tenders are called to accept a tender in whole or in part or reject any tender or all tenders without assigning reasons for any such action.
Before submitting a tender, the tenderer will be deemed to have satisfied himself by actual inspection of the site and locality of the works, that all conditions liable to be encountered during the execution of the works are taken into account and that the rates he enters in the tender forms are adequate and all inclusive to accord with the provisions in Clause-37 of the Standard General Conditions of Contract for the completion of works to the entire satisfaction of the Engineer.
Tenderers will examine the various provisions of The Central Goods and Services Tax Act, 2017(CGST)/ Integrated Goods and Services Tax Act, 2017(IGST)/ Union Territory Goods and Services Tax Act, 2017(UTGST)/ respective state's State Goods and Services Tax Act (SGST) also, as notified by Central/State Govt.& as amended from time to time and applicable taxes before bidding. Tenderers will ensure that full benefit of Input Tax Credit (ITC) likely to be availed by them is duly considered while quoting rates.
The successful tenderer who is liable to be registered under CGST/IGST/UTGST/SGST Act shall submit GSTIN along with other details required under CGST/IGST/UTGST/SGST Act to railway immediately after the award of contract, without which no payment shall be released to the Contractor. The Contractor shall be responsible for deposition of applicable GST to the concerned authority.
In case the successful tenderer is not liable to be registered under CGST/IGST/UTGST/ SGST Act, the railway shall deduct the applicable GST from his/their bills under reverse charge mechanism (RCM) and deposit the same to the concerned authority.
INSPECTION AND TESTING: All materials will be subjected to inspection and test by RITES/authorized railway representative at the Manufacturer's workshop/site before dispatch and no materials shall be dispatched from the Manufacturer's workshop/ site until these are inspected and or approved. The materials may also be inspected by the purchaser or his representative or any organization recommended by the purchaser again at the contractor's depot/works site. The purchaser or his representatives or any organization recommended by the purchaser shall have the right to be present during all stages of manufacturing and shall be offered, free of charge all reasonable facilities for inspection and testing so as to satisfy himself/ themselves that the materials are in accordance with specifications, approved drawings and designs. Any unreasonable delay in inspection will be a reasonable ground for extension of time for completion of work. Not less than 15(fifteen) days notice in writing shall be given by the contractor to the purchaser in order that the purchaser's Engineer may be present if they (i.e.purchaser) so desire, carrying out the inspection and test.
The firm should ensure that minimum wages is to be paid to their employee as per the extant Government rule. It will befirm's responsibility to resolve the issues if any dispute arises regarding non payment of minimum wages to their employees and Railway will not be responsible for this.
The tenderers in case of other than Company/Proprietary firm, Annexure -V(A) shall also be submitted by the each member of a Partnership Firm / Joint Venture (JV) / Hindu Undivided Family (HUF) / Limited Liability Partnership (LLP) etc. as the case may be. Non submission of above certificate by the bidder shall result in summarily rejection of his/their bid. It shall be mandatorily incumbent upon the tenderer to identify, state and submit the supporting documents duly self-attested/digitally signed by which they/he is qualifying the Qualifying Criteria mentioned in the Tender Document.
The Railway reserves the right to verify all statements, information and documents submitted by the bidder in his tender offer, and the bidder shall, when so required by the Railway, make available all such information, evidence and documents as may be necessary for such verification. Any such verification or lack of such verification, by the Railway shall not relieve the bidder of its obligations or liabilities hereunder nor will it affect any rights of the Railway thereunder.
In case of any information submitted by tenderer is found to be false, forged or incorrect at any time during process for evaluation of tenders, it shall lead to forfeiture of the tender Bid Security besides banning of business for a period of up to two years.
In case of any information submitted by tenderer is found to be false, forged or incorrect after the award of contract, the contract shall be terminated. Bid security, Performance Guarantee and Security Deposit available with the railway shall be forfeited. In addition, other dues of the contractor, if any, under this contract shall be forfeited and agency shall be banned for doing business for a period of up to two years.
Any changes in GST rate (increase/decrease) as the casemay be shall applicable in the contract and will be paid by the firm/Railway.
The rates quoted shall be FIRM and shall include all statutory obligations on the part of the contractor.
Restrictions on the Employment of Retired Engineers of Railway Services Within One Year of their Retirement: The Contractor shall not, if he is a retired Government Engineer of Gazetted rank, himself engage in or employ or associate are tired Government Engineer of Gazetted rank, who has not completed one year from the date of retirement, in connection with this contract in any manner whatsoever without obtaining prior permission of the President and if the Contractor is found to have contravened this provision it will constitute a breach of contract and administration will been titled to terminate the contract and forfeit his Performance Guarantee as well as Security Deposit.
In the instant tender departmental valuation has been calculated with GST @ 18% and tenderer need to quote their rates with GST rate @ 18 %.
However, inter se ranking will be done on the quoted value including GST applicable on the date of opening.
Shramikkalyan portal:- (i) Contractor is to abide by the provisions of various labour laws in terms of above clause 54,55, 55-A and 55-B of Indian Railways Standard General Conditions of Contract. In order to ensure the same, an application has been developed and hosted on website 'www.shramikkalyan.indianrailways.gov.in'. Contractor shall register his firm/company etc. and upload requisite details of labour and their payment inthis portal. These details shallbe available in public domain. The registration /updation in Portal shall be done as under: (a)Contractor shall apply for one time registration of his company/firm etc. in the Shramikkalyan portal with requisite details subsequent to issue of Letter of Acceptance. Engineer shall approve the contractor's registration in the portal within 7 days of receipt of such request. (b)Contractor once approved by any Engineer, can create password with login ID (PAN No.) for subsequent use of portal for all Letter of Acceptances (LoAs)issued in his favour. (c)The contractor once registered on the portal, shall provide details of his Letter of Acceptances (LoAs)/ Contract Agreements on shramikkalyan portal within 15 days of issue of any LoA for approval of concerned Engineer. Engineer shall update (if required) and approve the details of LoA filled by contractor within 7 days of receipt of such request.(d)After approval of LoA by Engineer, contractor shall fill the salient details of contract labours engaged in the contract and ensure updating ofeach wage payment to them on shramikkalyan portal on monthly basis. (e)It shall be mandatory upon the contractor to ensure correct and prompt uploading of all salient details of engaged contractual labour & payments made thereof after each wage period. (ii)While processing payment of any'On Account Bill' or 'Final Bill' or release of 'Advances' or 'Performance Guarantee / Security deposit', contractor shall submit a certificate to the Engineer or Engineer's representatives that "I have uploaded the correct details of contract labours engaged in connection with this contract and payments made to them during the wage period in Railway's Shramikkalyan portal at 'www.shramikkalyan.indianrailways.gov.in' till____Month,____Year.
The e-tender or other attached documents connected there with should be digitally signed using digital signature of authorized person only.
If the date of opening happens to be a BANDH or Holiday or Natural calamities, the tender will be opened at the same time on the following working day.
ON ACCOUNT AND FINAL PAYMENT: On account and final payment will be made duly following the Payment Terms attached with the tender document.
In case of increase or decrease in GST rate, same will be either paid by Railway or recovered from the agency as the case may be.
Electrical work for Improvement of old non functional CSY well by providing new DI 300 Dia pipe line with st.structure near CSY halt with 200000G ground reservoir under SSEE/HT/PUMP at Kharagpur.
114-ELC-G-KGP-26-27-13-R1~SER
114-ELC-G-KGP-26-27-13-R1
Open
Works - General
9 Months
Paschim Medinipur, West Bengal
₹0
₹2.4 L
3 Sept 2026
3 Sept 2026
11 Sept 2026
65 items across 1 schedule · ₹1,21,01,490.39 total
| # | Description | Unit | Qty | Rate | Amount |
|---|---|---|---|---|---|
| 1 | Supply, Installation, Testing & Commissioning of HT panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting of 12KV, 40KA, 800 Amps Indoor type Incoming Microprocessor based VCB-01 Nos. (CT ratio 200/100/50/5) and 12KV, 40KA, 800 Amps Indoor type Outgoing microprocessor based VCB.-02 Nos. (CT ratio 200/100/50/5) with all other accessories i.e. Power Pack, Battery and SMPS Battery Charger, complete set of digital ammeter, voltmeter, multifunctional meters, led indicator, CT, PT, Protective relay etc. with suitable metallic enclosure and complete wiring to complete the job with 1250Amp capacity Cu. Bus-Bar and with Electrical and Manual Mechanical interlocking facilities. | Set | 1.00 | 20,38,436.78 | 20,38,436.78 |
| 2 | Supply with testing of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole Draw-out ACB 800 A, 50KA, Microprocessor Based SR18G, MDO type - 02 Nos. as incoming, 4-pole Draw-out ACB 800 A, 50KA, Microprocessor Based SR18G, MDO type - 01 No. as Bus-Coupler and 4-pole 400A 50kA microprocessor based MCCB -02 nos., 4- pole 250A 36kA microprocessor based MCCB - 02 nos., 4-pole 100A 36kA microprocessor based MCCB -02 nos. and 4-pole 63A, 10kA MCB with 4PP -02 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing ACB & MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. | Set | 1.00 | 11,18,181.12 | 11,18,181.12 |
| 3 | Fixing and commissioning of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole Draw-out ACB 800 A, 50KA, Microprocessor Based SR18G, MDO type - 02 Nos. as incoming, 4-pole Draw-out ACB 800 A, 50KA, Microprocessor Based SR18G, MDO type - 01 No. as Bus-Coupler and 4-pole 400A 50kA microprocessor based MCCB -02 nos., 4- pole 250A 36kA microprocessor based MCCB - 02 nos., 4-pole 100A 36kA microprocessor based MCCB -02 nos. and 4-pole 63A, 10kA MCB with 4PP -02 nos. as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing ACB & MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. | Set | 1.00 | 40,726.17 | 40,726.17 |
| 4 | Supply with testing of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 630A 50kA microprocessor based MCCB - 01 No. as incoming and 4-pole 250A 36kA microprocessor based MCCB- 04 Nos, 4-pole 63A 36kA microprocessor based MCCB- 04 Nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. | Set | 1.00 | 3,05,212 | 3,05,212 |
| 5 | Fixing and commissioning of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 630A 50kA microprocessor based MCCB - 01 No. as incoming and 4-pole 250A 36kA microprocessor based MCCB- 04 Nos, 4- pole 63A 36kA microprocessor based MCCB- 04 Nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. | Set | 1.00 | 2,977.93 | 2,977.93 |
| 6 | Supply with testing of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4- pole 250A 36kA microprocessor based MCCB - 01 No. as incoming and 4-pole 63A 36kA microprocessor based MCCB- 06 Nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point duly conforming PCEE/SER/GRC Specification of LT Distribution Panel as applicable with Description No. SER/ELEC/GS/ DESCRIPTION/LT PANEL/1/REV- 2/JUNE 2025, Dtd.16/06/2025. | Set | 2.00 | 1,43,898 | 2,87,796 |
| 7 | Fixing and commissioning of Indoor Type LT Panel made of Powder Coated CRCA Sheet Steel of thickness (minimum): 2mm with Ingress Protection: IP 53 or higher consisting with 4-pole 250A 36kA microprocessor based MCCB - 01 No. as incoming and 4-pole 63A 36kA microprocessor based MCCB- 06 Nos as outgoing with suitable Cu. Bus bar, Digital Multifunctional Meter in all Incoming & Outgoing MCCB, Capable to measure and display Voltage, Current, Frequency, Power factor, kW, kVAR, kWh, kVAh, kVARh etc., appropriate spreader link for MCCB, Automatic Fire Ball, Insulating Mats and with necessary item for seal the cable entry and outgoing point and all other Civil work and accessories to complete job. | Set | 2.00 | 2,977.93 | 5,955.86 |
| 8 | Erection, testing and commissioning of Outdoor type transformer 250 KVA (as a new or in replacement), 11KV/415V, 3 phase, 50Hz, Oil cooled, copper wound complete with oil and other accessories including making of transformer plinth, brick walling and fencing as mentioned in GEN. Necessary tools/ropes/ man power are to be arranged by the Contractor. The cost also includes crane charges if required as per site condition. | Numbers | 3.00 | 53,045.63 | 1,59,136.89 |
| 9 | Laying, supply at site, testing, drawl & commissioning of HT cable underground along the road through cable trench as mentioned in explanatory note. | Metre | 6800.00 | 213.37 | 14,50,916 |
| 10 | Laying of HT cable/cables across the road, track, drain, concrete etc. through HDPE/GI/RCC pipe as mentioned in explanatory note. | Metre | 100.00 | 538.17 | 53,817 |
| 11 | Laying, supply at site, testing, drawl & commissioning of HT cable on wall, PVC sleeve/Pipe as mentioned in explanatory note. | Metre | 100.00 | 72.61 | 7,261 |
| 12 | Supply of HT 11 KV Heat shrinkable type End Termination Kit Indoor type suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 12.00 | 7,497.63 | 89,971.56 |
| 13 | Fixing and commissioning of HT 11 KV Heat shrinkable type End Termination Kit Indoor type suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 12.00 | 927.01 | 11,124.12 |
| 14 | Supply of HT 11 KV Heat shrinkable type End Termination Kit Outdoor type suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 24.00 | 7,755 | 1,86,120 |
| 15 | Fixing and commissioning of HT 11 KV Heat shrinkable type End Termination Kit Outdoor type suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 24.00 | 927.01 | 22,248.24 |
| 16 | Supply of HT 11 KV Heat shrinkable Straight Through Joint Kit suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 9.00 | 9,570 | 86,130 |
| 17 | Fixing and Commissioning of HT 11 KV Heat shrinkable Straight Through Joint Kit suitable for 3 x 95 Sq.mm Screened XLPE cable 11KV/E. | Numbers | 9.00 | 927.01 | 8,343.09 |
| 18 | Supply of 110mm Outer Dia. HDPE pipe of Grade PE-100, PN 10 with all accessories like suitable couplers, plugs, end caps, spacer, T band etc. as mentioned in explanatory note. | Metre | 900.00 | 688.79 | 6,19,911 |
| 19 | Erection and commissioning of HDPE pipe of any size with all accessories to complete job. | Metre | 900.00 | 40.75 | 36,675 |
| 20 | Laying of LT cable/cables in underground along the road through cable trench etc. as mentioned in explanatory note. | Metre | 2000.00 | 148.43 | 2,96,860 |
| 21 | Laying of LT cable/cables across the road, track, drain through RCC/GI pipe as mentioned in explanatory note. | Metre | 200.00 | 339.77 | 67,954 |
| 22 | Laying of LT cable/cables on wall/structure through PVC casing pipe of size 4inches or 3inches with accessories as mentioned in explanatory note. | Metre | 300.00 | 102.07 | 30,621 |
| 23 | Laying of extra cables in the excavated same trench. | Metre | 500.00 | 18.42 | 9,210 |
| 24 | Transportation of cables (in rolls with or without wooden drums), poles and other materials and accessories from any store of Kharagpur Division to Work Site. | Each | 20.00 | 1,171.11 | 23,422.2 |
| 25 | Supply, transportation and fixing of RCC Cable Route Marker of size L-12", B-6" and H- 2.6" or as per site requirement with all accessories. | Numbers | 200.00 | 497.81 | 99,562 |
| 26 | Supply, erection, testing and commissioning of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 16-25 sq. mm XLPE aluminum conductor armored cable. | Set | 50.00 | 220.33 | 11,016.5 |
| 27 | Supply, erection, testing and commissioning of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 70-95 sq. mm XLPE aluminum conductor armored cable. | Set | 20.00 | 387.39 | 7,747.8 |
| 28 | Supply, erection, testing and commissioning of LT XLPE cable gland made of Brass with aluminum lugs/sockets (4 Nos.) suitable for termination work of LT 4 Core X 185-300 sq. mm XLPE aluminum conductor armored cable. | Set | 20.00 | 650 | 13,000 |
| 29 | Supply, fitment, testing and commissioning of LT Heat shrinkable type Straight Through Joint Kit suitable for 4 x 120-185 Sq.mm Screened XLPE LT U/G cable. | Set | 10.00 | 2,635.03 | 26,350.3 |
| 30 | Supply of Strip Galvanized Perforated type Cable Tray of Size- Width (minimum): 150mm, Height (minimum): 60mm, Thickness: 0.6mm or above based on OEM design as per support spacing, Having Slotted Rung Spacing with suitable accessories required to complete job as mentioned in explanatory note. | Metre | 250.00 | 718 | 1,79,500 |
| 31 | Laying and fixing of Strip Galvanized Perforated type Cable Tray with all accessories mentioned in Explanatory Note to complete job. | Metre | 250.00 | 83.92 | 20,980 |
| 32 | Concealed Wiring of light and fan point by 1.5 Sq. mm, Single Core, Copper wire each for phase & neutral with 1.5 Sq. mm, Single Core, Copper wire for Earthing through PVC Conduit Pipe of Nominal Size 20mm/25mm (as per site requirement) including supply and fixing of all required materials like modular switch, socket, lamp holder, ceiling rose with suitable flush metal boxes, front plate etc. as per specifications mentioned in explanatory note. | Point | 80.00 | 898 | 71,840 |
| 33 | Concealed Sub Circuit wiring by 2.5 sq. mm, Single Core, Copper wire each for phase & neutral with 2.5 Sq. mm, Single Core, Copper wire for Earthing through PVC Conduit Pipe of Nominal Size 25mm including supply and fixing of all required materials like ceiling rose, suitable flush metal boxes, front plate etc. as per specifications mentioned in explanatory note. | Metre | 300.00 | 182.58 | 54,774 |
| 34 | Supply of Batten with 20 W LED tube light with Colour Rendering Index (CRI) >=80, confirming IP20 (with integrated electronic driver) as per specifications mentioned in explanatory note. | Numbers | 20.00 | 244.98 | 4,899.6 |
| 35 | Fixing and Commissioning of any kind of Batten with 18W or higher wattage LED tube light with necessary accessories. | Numbers | 20.00 | 38.52 | 770.4 |
| 36 | Supply of BEE: 5 Star rated High Speed BLDC Ceiling Fan, 1200 mm Sweep, Material of Blade- Aluminium, Motor winding material: Copper, Rated Voltage: 230V, 50Hz, Single phase AC with step type electronic fan regulator and necessary accessories as per specifications mentioned in explanatory note. | Numbers | 5.00 | 3,238 | 16,190 |
| 37 | Fixing and commissioning of Ceiling Fan with 1200 mm Sweep, step type electronic fan regulator with necessary accessories to complete job. | Numbers | 5.00 | 108.57 | 542.85 |
| 38 | Erection, Testing & Commissioning of VT Pump & Motor Set of Capacity 50,000 GPH with 100 HP Motor, suitable for 415V, 50Hz, 3- Phase power supply along with Soft Starter Panel, Column pipes, mandatory spares and accessories like Non-return valve with by-pass arrangement of suitable side at delivery end, Flanged type sluice valve of suitable size for delivery side, Delivery pressure gauge with cock, dial type of suitable capacity, Jaw flex type coupling, foundation nuts & bolts, Pressure Gauges as per site requirement. Cost includes the cost of all accessories to complete the work in all respect including foundation work & all other ancillary work (if required) cost includes the commissioning of motor, starter & Pump to complete the work in all respect. | Numbers | 2.00 | 2,76,841.81 | 5,53,683.62 |
| 39 | Design, Manufacturing, Supply, Erection & Commissioning of 2 Ton Capacity SGEOT Crane along with- (i)Fabrication, Transportation on-site and Erection of LT Gantry line suitable for 01 no. of 02 Tons SGEOT Crane - bay length of 16 Mts (Each Side), (ii)Supply, Fabrication & Erection of SGEOT Gantry Way- Made of ISMB 200 mm with stiffeners/ Joint/ plates of 10 mm, with 40 mm Solid Bright Bar (ISMB-SAIL/JINDAL Make) 16m x 2No= 32m and (iii)Supply and Installation of DSL LT power feeding. | Set | 1.00 | 14,26,658 | 14,26,658 |
| 40 | Supply of 15 HP Three Phase Energy Efficient Open Well Submersible Pump, Motor Capacity: 11.3 KW, 3Ph, 415V AC, Delivery Size 65-80mm or as per requirement of consignee, Head- 60-70Mtr or as per requirement of consignee, Conforming to IS: 8034- 2002 with all necessary items require for successful installation of pump as per site requirement and direction of consignee. | Numbers | 6.00 | 61,360 | 3,68,160 |
| 41 | Supply of 20 HP fully automatic star-delta Starter Control Panel for 3-Phase Submersible Pump in powder coated CRCA sheet steel enclosure with necessary arrangement as mentioned in explanatory note. | Set | 6.00 | 29,695 | 1,78,170 |
| 42 | Supply of Submersible flat cable of size 3 Core x 6.00 Sq.mm PVC Insulated & PVC Sheathed Copper Conductor as mentioned in explanatory note. | Metre | 700.00 | 188 | 1,31,600 |
| 43 | Supply of Lead free UPVC Submersible Heavy Duty Hi-Tech Hi-Tensile Biaxial Oriented Column Pipe (approximate Inner Dia- 80mm & Outer Dia- 90mm) or as per site and size requirement for the above mentioned Submersible Pump with suitable couplers, Length: 3Mtr per pipe, Pressure Bearing Capacity: 15 Kgf/Sq.cm or above as relevant per IS standard. | Numbers | 150.00 | 2,186.54 | 3,27,981 |
| 44 | Supply of Nylon rope 25 mm dia. or as per site and size requirement for the Submersible Pump, Conforming to relevant IS. | Metre | 1000.00 | 115.48 | 1,15,480 |
| 45 | Lowering, complete installation and commissioning of Open-well Submersible Pump with all accessories with reducing socket, Stainless Steel nut-bolt as per site requirement to complete job of pump with all accessories. | Set | 6.00 | 10,610.45 | 63,662.7 |
| 46 | Supply of 5M HDG (Hot Dip Galvanized) Octagonal Pole with cable junction compartment, Pole top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)-200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. as per specifications mentioned in explanatory note. | Numbers | 20.00 | 11,198.2 | 2,23,964 |
| 47 | Supply of Insulated Cable Connector 4-way and SP 6A MCB, Type B- 01 No. along with Bakelite sheet for Octagonal Pole. | Set | 20.00 | 399.73 | 7,994.6 |
| 48 | Fixing and Commissioning of 5M HDG (Hot Dip Galvanized) Octagonal Pole, top dia. 70mm, bottom dia. 130mm, sheet thickness 3mm, base plate dimensions (L X B X T)- 200mm X 200mm X 12mm with 500 mm long single/double arm and foundation bolts etc. with RCC foundation works to complete the job as per specifications mentioned in explanatory note. | Numbers | 20.00 | 1,972.55 | 39,451 |
| 49 | Supply of LED 45 watt or higher wattage street light with Colour Rendering Index (CRI) >=70, confirming IP66 as per specifications mentioned in explanatory note. | Numbers | 25.00 | 2,348.27 | 58,706.75 |
| 50 | Fixing and commissioning of LED 45 watt or higher wattage street light including wiring of light from loop box. | Numbers | 25.00 | 229.92 | 5,748 |
| 51 | Handling, cutting (to required size) and transportation of Rail Pole to work site including painting of pole and erection. | Each | 20.00 | 1,517.7 | 30,354 |
| 52 | Excavation of pit size 750 x 750 x 1828 mm or appropriate size as per site requirement in any kind of soil as available at site and erection of Rail pole/PSC pole, guy set etc. And filling up with 1:3:6 cement concrete including the length of muffing of base. | cum | 40.00 | 4,951.76 | 1,98,070.4 |
| 53 | Fabrication and erection for 4-Pole/ 2-Pole structure including supply of MS channels of required size, angle and all small parts like G.I. Clamp, nuts, bolts etc. as required by consignee depending upon work requirements excluding Rail Pole/ PSC pole. (Pole will be supplied by Rly.) and all accessories to complete the work in all respect. | MT | 2.00 | 43,254.44 | 86,508.88 |
| 54 | Supply of Anti Climbing Device made of GI barbed wire, Clamping arrangement etc. (2 Kg Per Support) or as per site requirement to complete the job. | Kg | 40.00 | 74.8 | 2,992 |
| 55 | Supply of 11KV 400 Amps A.B Switch complete with expulsion type drop out fuse and lighting arrestor. | Numbers | 8.00 | 20,350.43 | 1,62,803.44 |
| 56 | Installation of 11KV 400 Amps A.B Switch complete with expulsion type drop out fuse and lighting arrestor. | Numbers | 8.00 | 2,742.78 | 21,942.24 |
| 57 | Supply of fencing panels at switching stations. | Metre | 50.00 | 2,846.63 | 1,42,331.5 |
| 58 | Erection of fencing panels at switching stations. | Metre | 50.00 | 79.48 | 3,974 |
| 59 | Supply of fencing uprights at switching stations. | MT | 1.00 | 83,541.28 | 83,541.28 |
| 60 | Erection of fencing uprights at switching stations. | MT | 1.00 | 2,456.91 | 2,456.91 |
| 61 | Supply & spreading of Ballast/Gravel in the Switch Yard. | Sqm | 40.00 | 1,077 | 43,080 |
| 62 | Supply, laying, fixing and commissioning of 25 x 3mm GI strip as and where required extra for earth connection between earth electrode and main switch/ DB/ Electric pole etc. as per site supervisor's instruction, including connection & termination with stainless steel nut, bolt, spring, washer etc. as required. | Metre | 600.00 | 112.17 | 67,302 |
| 63 | Supply of Earthing arrangement with supply of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes supply of all materials mentioned in the Drawing including 02 meters 25 x 3mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc. | Each | 50.00 | 4,119.67 | 2,05,983.5 |
| 64 | Erection of Earthing arrangement with erection of Hot Dip Galvanized (HDG) earth cone and all other requisite materials as per CEE/GRC's Drg. No.CEE/G/A3/P-150, Alt.1 including sump box, cover with salt and charcoal etc. as per site supervisor's instruction. Cost includes erection of all materials mentioned in the Drawing including 02 meters 25 x 3mm GI strip for connection from earth electrode pipe to light pole /Rail pole etc. | Each | 50.00 | 993.86 | 49,693 |
| 65 | Preparation and Submission of Drawings of Wiring Lay Out, Cable Route Lay out, Single Line Diagram of Power Distribution System etc. related to this work. The cost also includes supply of 11 copies of drawing. | Job | 3.00 | 11,005.72 | 33,017.16 |
| Schedule total | ₹1,21,01,490.39 | ||||
Tap a document below to read it instantly. You can also download everything as a ZIP if you prefer.
details.html
HTML
nit.pdf
NIT
VCBpanel-14-12-23.pdf
ATTACHMENT
GEN-Csy-Pump.pdf
ATTACHMENT
Annexure-VA.pdf
ATTACHMENT
Declerationregardingretdrlyemployee.pdf Declaration Retired Rly Employee
ATTACHMENT
BidSecurityAnnexure-VIA.pdf
ATTACHMENT
IndemnityBond.pdf
ATTACHMENT
NEFTMandateForm.pdf
ATTACHMENT
Declerationregardingretdrlyemployee.pdf
ATTACHMENT
Performancereportsheet.pdf
ATTACHMENT
JPOfordiggnigwork.pdf
ATTACHMENT
FinancialEligibilityAnnexure-VIB.pdf
ATTACHMENT
Tendererform.pdf
ATTACHMENT
CEE_G_A3_P-150_Alt.1-EarthingDrg.Spec..pdf
ATTACHMENT
HQLTPanelSpec-16-06-25.pdf
ATTACHMENT
PaymentConditionsLatest.pdf
ATTACHMENT
PoliceVerificationLetter.pdf
ATTACHMENT
Similar-Nature-Work-Consolidated-02-04-26.pdf
ATTACHMENT
ImplementationofLabourLaws.pdf
ATTACHMENT
Download all tender documents and submit your bid
Disclaimer: TenderKart has made every reasonable effort to ensure that the information on this page is accurate and authentic, however it cannot be held liable for any third-party claims or losses or any damages. TenderKart makes no warranty, expressed or implied, as to the results obtained from the use of this information. If you notice any error or omission, please let us know at .