Construction of Minister Bungalow in Smart City campus at Ranchi Jharkhand

Amount

BUILDING WORK

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaMTR.er holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centring and shuttering items )

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 MTR.re or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing and fixing of Glass fibre reinforced concrete (G.R.C) Stone Wall cladding Tiles of Random size of thickness 10-20 mm of approved design, colour, size, thickness, texture and pattern. The tile should be made with ‘53’ grade white Portland cement, reinforced with alkali resistant glass fibre with synthetic inorganic pigments manufactured by Bayferrox or equivalent with graded quartz, super plasticizers and integrated water proffers and other additives and top surface to be sealed with acrylic lacquer coating. Tiles should be fixed over 20 mm thick cement mortar 1:3(1 Cement: 3 Coarse sand) and filled with suitable grouting materials as per direction of site.

Providing of Glass Reinforced Concrete (G.R.C) Slanting Roof Elevation Tiles Slant Finish in approved color. The thickness of the tiles should be 10 mm, allowing variance of±2 mm in accordance with IS: 1237‐1980. The composition of tiles should be ‘43’ Grade White Portland cement, reinforced with Alkali Resistant Glass Fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated waterproofing agents and others. The tiles should be produced with high vibration technology and should have compressive strength equivalent to M‐40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. (GRC Roofing Tiles)

Providing and fixing in position about 50mm thick border and 35mm thick design Jali at all levels made from Glass fibre reinforced concrete (GRC) using white cement, Quartz Sand, AR Fibres, Water Plasticizers & pigments in approved shape, size and length as per the design and drawings and as per specifications, mix design and test results given below. The typical Screen should be of sizes as per the drawings. Fixing of GRC Jali shall be with help of S.S. Screws Fixtures, M.S Angle Cleats, Fissure Plug, and Dowel Pin proper alignment as per drawings (Shop drawings to be Submitted by the contractor before the work start). As per approved paint, shade & Finishing with GRC powder & filling the joints with Epoxy sealant neatly between GRC screen and primary structures. The Screen should be in absolute straight plumb line and length and joins between channels should be neatly filed to make seamless uniform surface across the entire elevation of the building without any visibility to joints. Any framework to be paid extra as per item.(GRC Screen)

Providing and fixing Glass Reinforced Concrete (G.R.C) Column with Capitol and Base of in approved design, pattern, size and colour to be cladded on existing structure of MS or RCC. The column set shall include Capitol and Base in accordance to the size and length of the column. The GRC column should be made from ‘53 grade’ Cement manufactured by ‘JK/BIRLA Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘N.E.G. JAPAN’ or equivalent, Super Plasticizers manufactured by ‘SIKA’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Mould or equivalent. The fixing of column should be ‘Dry fixing’ as per the drawings approved by engineer in charge. the cost includes the cost of scaffolding for height upto 12mtr. The column set shall include Capitol and Base in accordance to the size and length of the column. Frame work to be paid extra as per drawings.

Providing and Fixing Glass Reinforced Concrete (G.R.C) False cornice in size of 100x100 mm in approved colour, at all heights up to 12mtr height including scaffolding. The cornice should be made from ’53 Grade’ cement manufactured by ‘JK/Birla Cement’ or equivalent, Quartz, Fine silica sand, Alkali resistant Glass Fiber manufactured by ‘N.E.G Japan’ or equivalent. Super plasticizers manufactured by ‘BASF or equivalent’ and UV resistant synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX” (Germany) or equivalent. The material casting should take place in FRP mould or equivalent. The fixing of cornice should be ‘Dry Fixing’ as per the drawing approved by engineer in charge.

Providing and Fixing Glass Reinforced Concrete (G.R.C) False cornice in size of 175x155 mm in approved colour, at all heights up to 12mtr height including scaffolding. The cornice should be made from ’53 Grade’ cement manufactured by ‘JK/Birla Cement’ or equivalent, Quartz, Fine silica sand, Alkali resistant Glass Fiber manufactured by ‘N.E.G Japan’ or equivalent. Super plasticizers manufactured by ‘BASF or equivalent’ and UV resistant synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX” (Germany) or equivalent. The material casting should take place in FRP mould or equivalent. The fixing of cornice should be ‘Dry Fixing’ as per the drawing approved by engineer in charge.

Designing, Fabricating, Manufacturing, Installation and testing of Glass Reinforced Concrete G.R.C. Balustrades of make “Dalal Tiles” or equivalent in approved pattern, design, thickness and color with fixing method as per manufacturer, the Balusters and Handrail should be made from ’53 Grade’ approved white Portland cement in grade 18, quartz, fine silica sand, alkali resistant glass fiber manufactured. Polymers manufactured by approved manufacturer or equivalent, super plasticizers manufactured by approved manufacturer or equivalent with UV resistant synthetic inorganic pigments made by approved manufacturer or equivalent. The material casting should be done in synthetic rubber/FRP. Height of Balusters with handrail from be 750mm from the brick work and each balusters placed C/C 300mm and dia of each is 100mm as per approved design. Fixing of baluster to be fixed on/between RCC/Block work column or structural steel work with dry fixing method or grouting in blockwork with appropriate requirements, using approved fasteners, and necessary hardware etc. and fixing of handrail should be over MS Tube that should be mounted over balusters. The fixing shall be done by the specialized approved agency as directed by Engineer-in-charge.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering & scaffolding all complete as per direction of E/I

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water absorption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and fixing Glass mossaic tiles on finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in-Charge:

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming to IS: 15622, of approved make, in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including grouting the joints with white cement and matching pigments etc., complete. Size of Tile 1000x1000 mm.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing & fixing of laminate wooden flooring - Class 32(AC4) conforming to EN13329 standards ,thickness of plank minimum 8mm, size of plank- 1291mmx193mm,HDF core board to be swell stop plus with minimum density of 930 kg/m3 according to and conforming to EN622 type 5 standard. Product to be PEFC, FSC & Blue Angel certifications. Fixing to be done using 2mm PE foam and 0.2mm vapour barrier. Product to offer 20 years Gurantee for Residential/domestic use and 5 years Guarantee for commercial usage according to manufacturers guarantee document . Installation shold be done with authorised vendor. Equivalent to Floor Master..Approved Make- Floor Master, Eggar, Pergo

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, AS HIGHLIGHTER DESIGNER TILE of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), Jointing with grey cement slurry @ 3.3 kg/sqm including pointing the joints with white cement and matching pigment etc., complete.

Providing and laying machine cut, mirror polished Marble stone flooring, in required design (Simple geometrical, abstract etc.) and in patterns in combination with Italian marble stones of different colours, shades and finished surface texture etc., in linear portions of the building, all complete as per the architectural drawings, with 18 mm thick stone slab laid over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with white cement slurry @ 4.4 kg/sqm, including pointing with white cement slurry admixed with pigment to match the marble shade, including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. 18 mm thick Italian Marble stone slab, Perlato, Rosso verona, Fire Red or Dark Emperadore etc.

Providing average 150 mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/l.

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying , fitting and fixing 38 mm thick good quality well dressed well seasoned Teak wood fully paneled shutters in doors and windows with 25 mm thick panels with one side plain and other side chamfered with aluminium fittings such as hinges, sliding door, bolts, tower bolts, handles or rings, hooks and eyes, cleats, sand blocks as per schedule taxes and royalty all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Melamine polishing on wood work (one or more coat).

Providing and fixing SS finished tower bolts (600 x 23 x 40 MM 680 Grams) with with necessary screws, etc. all complete & instructionof Engineer in charge. 5 year warranty , Make Aquieen or equivalent , Material SS , Model No. TB651)

Providing and Fixing in position Door Handle type Lever (Dim. 180 x 48 x 9 mm) with door lock - with Brash finish , all complete in all respects as per drawing / design & instructionof Engineer in charge. (Make Godrej Model - SEC 01 Combi 2C Satin & Gold, Product Code - 7525)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing and fixing Godrej Locks C071 2 Speed Hydraulic 60kg Door Closer (Silver) body tubular type universal hydraulic door closer (Mounting on door panel or door frame ; Type: Lock ; Maximum Closing Moment: 14Nm ; Other Dimensions: Door Weight : 60 kg, Door Panel Width : 1050 mm, Door Opening Angle : 180°), with double speed adjustment with necessary accessories and screws etc.all complete & instructionof Engineer in charge. 1 Year warranty, Make Godrej , Material Silver , Model Locks C071 2 Speed

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coating and cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification of seepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entire treated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coat should be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entire treated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added in screed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc.

For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filled with polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mm to 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in charge Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

providing 12 mm thick waterproof cement plaster (1;3) cement :sand of F.M 1.5 With integral waterproofing compound liquid @125ml per bag of cement including screening,curing and all leads,lift of water,scaffolding taxes royalty all complete as per building specification and direction of E/I/ Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing rough cast plaster in 2 layer, the bottam layer being 12mm. thick in cement mortar (1:3) and top layer finished with gravel, pebbles or crushed stone as per specified cement mortar , (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Making 6X6mm grooves in plaster surface over walls truely horizontal or vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curring with all leads and lift of water all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required, scaffolding washing of floor and taxes all complete as per building specification and direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly, scaffolding and taxes all complete as per building specification and direciton of E/l.

Providing and fixing 12 mm thick frameless toughened glass canopy for porch area with SS studs fitting to secure with EPDM gasket all completemaking necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in-charge

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour casement/casement cum fixed glazed windows comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, stainless steel (SS 304 grade) friction hinges, zinc alloy (white powder coated) casement handles, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately) Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerancein dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made.) Casement window single panel with S.S. friction hinges (300x 19 x 1.9 mm), made of (small series) frame 47 x 50 mm & sash 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glass pane glazing bead of appropriate dimension. (Area of window upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding door made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead/ double glazing bead of appropriate dimension. (Area of door above 5.00 sqm)

Providing and fixing factory made uPVC white colour sliding glazed door comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension uPVC extruded glazing beads, uPVC extruded interlock and uPVC extruded Inline sash adaptor (if required), EPDM gasket, wool pile, zinc alloy (white powder coated) handle with key on one side of extreme panels along with zinc plated mild steel multi point locking having transmission gear with keeps, zinc alloy (white powder coated) cresent lock (if required), stainless steel (SS 304 grade) body with adjustable double nylon rollers (weight bearing capacity to be 120 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately). Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding door with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 82 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of door above 2.00 sqm upto 5.00 sqm)

Providing and fixing factory made uPVC white colour casement/ Casement cum fixed glazed door comprising of uPVC multi-chambered frame, sash and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, zinc alloy (white powder coated) 3D hinges and one handle on each side of panels along with zinc plated mild steel multi point locking having transmission gear, cylinder with keeps and one side key, G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws, etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealent shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Casement door with top hung ventilator with 3D and S.S. friction hinges (400 x 19 x 1.9 mm) made of (big series) frame 67 x 64 mm, sash 67 x 110 mm & mullion 67 x 80 mm all having wall thickness of 2.3 ±. 0.2 mm and single glazing bead / double glazing bead of appropriate dimension.(Area of door upto 2.50 sqm)

Providing, assembling and supplying vision glass panels (IGUs) comprising of herMTR.ically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in SQM. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/SQM degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

P/Fixing at all heights designer stepped POP false ceiling with framing and GI ceiling section, intermediate runners and angle, perimeter, give flush finish etc.including in provision for lighting.

P/making cove in POP false celing with the help of p.o.p and G.I perimeter etc.

P/Fixing at all heights designer stepped POP false ceiling with framing and GI ceiling section, intermediate runners and angle, perimeter, give flush finish etc.including in provision for lighting.

P/making cove in POP false celing with the help of p.o.p and G.I perimeter etc.

P/Fixing at all heights designer stepped POP false ceiling with framing and GI ceiling section, intermediate runners and angle, perimeter, give flush finish etc.including in provision for lighting.

P/making cove in POP false celing with the help of p.o.p and G.I perimeter etc.

Providing & Fixing 4mm thk veneer wooden false ceiling , made in 50x50mm Teak wood frame center to center 600mm both ways, hang to ceiling with help of hanger support 'L' type G.I angle (25x25mm) and anchor bolt etc. over fixed 11mm thick MDF board with 10x8mm deep groove finish with melamine polish, 4.0 mm thick approved shadenatural veneer to fixed on MDF board, defects free bubbles free with help of adhesive. as per drawing and to the entire satisfaction of Engineer in charge. ( MDF Boad & veneer Make Green ply/Century /Merino or Equivalent ,Adhesive make Pidilite or equivalent)

Providing and fixing false ceiling at all height including providing fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and making cove in gypsum board.false celing and G.I perimeter etc. as per drawing and instruction of Engineer in charge

Providing & Fixing 4mm thk veneer wooden false ceiling , made in 50x50mm Teak wood frame center to center 600mm both ways, hang to ceiling with help of hanger support 'L' type G.I angle (25x25mm) and anchor bolt etc. over fixed 11mm thick MDF board with 10x8mm deep groove finish with melamine polish, 4.0 mm thick approved shadenatural veneer to fixed on MDF board, defects free bubbles free with help of adhesive. as per drawing and to the entire satisfaction of Engineer in charge. ( MDF Boad & veneer Make Green ply/Century /Merino or Equivalent ,Adhesive make Pidilite or equivalent)

Providing and making cove in gypsum board.false celing and G.I perimeter etc. as per drawing and instruction of Engineer in charge

Providing and fixing GI Clip in MTR.al Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the periMTR.er of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. including fixing periMTR.er channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the periMTR.er of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMTR.er channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of periMTR.er channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I. All sections to be galvanized @ 120 gms/SQM (both side inclusive), fixing with clip in tiles into spring 'T' with: GI MTR.al Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ SQM (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing & Fixing Electric Fire place - indoor /oudoor Bio Fuel Firewave - Size 1820mm length Cavity cut-out size - 1805X185mm made in Stainless Steel with 10 Litres volume capacity bio fuel, Fuel Consumption 1 HR – 1 HR 25 MINS Per LIT ,Thermal Output-10,000-16000 BTU/HR ,Burning Time MIN 9 HRS, Max 14 HRS including 5 Year Replacement Guarantee. all complete All work to be carried out as per drawing and instruction of Engineer in charge. (Make Germany or equivalent)

Providing and fixing Armstrong Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm in finish as/ spec – Pradoo & Cabrueava. The baffle blade shall be suspended using Slotted U-profile at on-center spacing in multiples of 200 c/cmm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. Installation of U-Grid:The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter. Installation of Armstrong Baffles: Locate the slot for Baffle Hangers in slot of Baffle section at 1200mm centres. Hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. Baffle to be lifted into position and hangers engage over lip of U-Grid Channel. Each Hanger to be secured into position by inserting the Locking Clip. Baffles blades to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile.End Caps to be located by pushing the End Cap tongues into Baffle slots.Installation shall be according to the instructions provided by manufacturer.

BORING

HYDT: - Cost of Driling 200mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools, driling rig, air compressure and equipments as well as fule, lubricants and cost of transportation of rig machine annd other vehical up to Site. (4 Nos.)

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to200.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia UPVC.

Supplying all tools, equipments and labour and doing washing and flushing and development of drilled tube well to give clean and clear water all complete as per direction of E/I.

Supplying labour, cement and calcium cloride or bentonite solution and equipments for groutinf the casing pipe after lowering in the bore including carriage of material to work site etc.all complete as per specification and direction of E/I.

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages - 5 HP

D.O.L starter with S.S Enclosure with 380/415 Volt coil as per IS 3914 - upto 5 HP.

3 crore PVC insulated, PVC sheathed copper conductor flat submersible cable- Supplying, Flat flexible submersible cable with, copper conductor, PVC insulated and PVC sheathed. 3 core 4 sqmm

Supplying and lowering 40 mm dia. Column PVC pipe with all complete job.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

BUNGALOW BOUNDARY WALL

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/SQM including pointing in white cement complete. Granite of any colour and shade

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

MINISTER BUNGALOW CAMPUS BOUNDARY WALL

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Excavating, supplying and filling of local earth (including royalty) by mechanical transport upto a lead of 5km also including ramming and watering of the earth in layers not exceeding 20 cm in trenches, plinth, sides of foundation etc. complete.

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing designation 75A brick work in C.M (1: 6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar, joints cost of screening materials raking out joints to 15mm depth , curring , taxes and royalty all complete as per builiding specification and direction of E/I.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

GUARD POST WITH MAIN GATE FOR MINISTER BUNGALOW

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for shuttering in circular work (20% of respective centring and shuttering items )

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 MTR.re or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing of Glass Reinforced Concrete (G.R.C) Slanting Roof Elevation Tiles Slant Finish in approved color. The thickness of the tiles should be 10 mm, allowing variance of±2 mm in accordance with IS: 1237‐1980. The composition of tiles should be ‘43’ Grade White Portland cement, reinforced with Alkali Resistant Glass Fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated waterproofing agents and others. The tiles should be produced with high vibration technology and should have compressive strength equivalent to M‐40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. (GRC Roofing Tiles)

Providing and fixing Glass Reinforced Concrete (G.R.C) Column with Capitol and Base of in approved design, pattern, size and colour to be cladded on existing structure of MS or RCC. The column set shall include Capitol and Base in accordance to the size and length of the column. The GRC column should be made from ‘53 grade’ Cement manufactured by ‘JK/BIRLA Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘N.E.G. JAPAN’ or equivalent, Super Plasticizers manufactured by ‘SIKA’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Mould or equivalent. The fixing of column should be ‘Dry fixing’ as per the drawings approved by engineer in charge. the cost includes the cost of scaffolding for height upto 12mtr. The column set shall include Capitol and Base in accordance to the size and length of the column. Frame work to be paid extra as per drawings.

Providing and Fixing Glass Reinforced Concrete (G.R.C) False cornice in size of 100x100 mm in approved colour, at all heights up to 12mtr height including scaffolding. The cornice should be made from ’53 Grade’ cement manufactured by ‘JK/Birla Cement’ or equivalent, Quartz, Fine silica sand, Alkali resistant Glass Fiber manufactured by ‘N.E.G Japan’ or equivalent. Super plasticizers manufactured by ‘BASF or equivalent’ and UV resistant synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX” (Germany) or equivalent. The material casting should take place in FRP mould or equivalent. The fixing of cornice should be ‘Dry Fixing’ as per the drawing approved by engineer in charge.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water absorption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Supplying, fitting and fixing oxidised iron fittings of approved quality and make to doors and windows all complete as per building specification and direction of E/l.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineering-charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Melamine polishing on wood work (two or more coat).

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing rough cast plaster in 2 layer, the bottam layer being 12mm. thick in cement mortar (1:3) and top layer finished with gravel, pebbles or crushed stone as per specified cement mortar , (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Making 6X6mm grooves in plaster surface over walls truely horizontal or vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curring with all leads and lift of water all complete as per building specification and direction of E/I.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Distempering with 1st quality acrylic distemper, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and m anufacture, including applying additional coats wherever required, to achieve even shade and colour. Two coats

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade : Two or more coats on new work

Extra for plastering exterior walls of height more than 10 m from ground level for every additional height of 3 m or part thereof.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing, assembling and supplying vision glass panels (IGUs) comprising of herMTR.ically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in SQM. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/SQM degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

CLUB HOUSE FOR MINISTER BUNGALOW

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaMTR.er holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for Stairs, (excluding landings) except spiral-staircases

Extra for shuttering in circular work (20% of respective centring and shuttering items )

Centering and shuttering including strutting, propping etc. and removal of form for : Cornices and mouldings

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 MTR.re or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing of Glass Reinforced Concrete (G.R.C) Slanting Roof Elevation Tiles Slant Finish in approved color. The thickness of the tiles should be 10 mm, allowing variance of±2 mm in accordance with IS: 1237‐1980. The composition of tiles should be ‘43’ Grade White Portland cement, reinforced with Alkali Resistant Glass Fiber and the pigmentation should be done with exterior grade synthetic inorganic iron oxide pigments manufactured by ‘BAYFERROX (Germany)’ or equivalent. The pigmentation should be homogeneous and in accordance with British Standards BS EN 12878:1999. The other additives should be fine washed graded quartz, super plasticizers and integrated waterproofing agents and others. The tiles should be produced with high vibration technology and should have compressive strength equivalent to M‐40 Grade@28 days. The top surface of the tiles should be sealed with acrylic lacquer resulting in surface water absorption of tiles, less than 1% and water absorption by 24 hrs immersion method, less than 8%. (GRC Roofing Tiles)

Providing and fixing Glass Reinforced Concrete (G.R.C) Column with Capitol and Base of in approved design, pattern, size and colour to be cladded on existing structure of MS or RCC. The column set shall include Capitol and Base in accordance to the size and length of the column. The GRC column should be made from ‘53 grade’ Cement manufactured by ‘JK/BIRLA Cement’ or equivalent, Quartz, Fine Silica Sand, Alkali Resistant Glass Fiber manufactured by ‘N.E.G. JAPAN’ or equivalent, Super Plasticizers manufactured by ‘SIKA’ or equivalent, Polymers manufactured by ‘BASF’ or equivalent and U.V resistant Synthetic inorganic pigments should be used for pigmentation manufactured by ‘BAYFERROX (Germany)’ or equivalent. The material casting should take place in FRP Mould or equivalent. The fixing of column should be ‘Dry fixing’ as per the drawings approved by engineer in charge. the cost includes the cost of scaffolding for height upto 12mtr. The column set shall include Capitol and Base in accordance to the size and length of the column. Frame work to be paid extra as per drawings.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering & scaffolding all complete as per direction of E/I

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water absorption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing of Armstrong American Exotics Bruce range of products with 7 Ply construction of cross ply with sealed edges for superior spill resistance Engineered wood. The length of the range varies from 400mm to 1200 mm, width being 120mm and thickness 10.5mm to give a variety of dimensional choices. The veneer thickness of the products remains to be 2mm.The plank shall have an unique locking system- “Lock & Fold” system. To protect the plank from moisture the edges are waxed to give superior protection. The edge offers you in micro bevelled shape with Permion finish in order to resist stains and spots. Equivalent to Armstrong engineered wood. Accesories will be paid extra. Installation should be done by a trained and authorised team.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Extra for filling grooves with polysulphide 6mm wide, 20mm deep.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Providing and fixing 12 mm thick frameless toughened glass GLAZING CUM DOOR shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & spring type fixing arrangement and making necessary holes etc. for fixing required door fittings and U channel under floor for fixed portion with silicon jointing fitting all complete as per direction of Engineer-in-charge

Melamine polishing on wood work (one or more coat).

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-in-charge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coating and cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification of seepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entire treated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coat should be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entire treated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added in screed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc.

For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filled with polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mm to 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in charge Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

providing 12 mm thick waterproof cement plaster (1;3) cement :sand of F.M 1.5 With integral waterproofing compound liquid @125ml per bag of cement including screening,curing and all leads,lift of water,scaffolding taxes royalty all complete as per building specification and direction of E/I/ Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Making 6X6mm grooves in plaster surface over walls truely horizontal or vertical as specified at regular intervals, at all heights including cleaning, finishing, scaffolding and curring with all leads and lift of water all complete as per building specification and direction of E/I.

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing, assembling and supplying vision glass panels (IGUs) comprising of herMTR.ically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in SQM. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/SQM degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and fixing false ceiling at all height including providing fixing of frame work made of special sections, power pressed from M.S. sheets and galvanized with zinc coating of 120 gms/sqm (both side inclusive) as per IS : 277 and consisting of angle cleats of size 25 mm wide x 1.6 mm thick with flanges of 27 mm and 37mm, at 1200 mm centre to centre, one flange fixed to the ceiling with dash fastener 12.5 mm dia x 50mm long with 6mm dia bolts, other flange of cleat fixed to the angle hangers of 25x10x0.50 mm of required length with nuts & bolts of required size and other end of angle hanger fixed with intermediate G.I. channels 45x15x0.9 mm running at the spacing of 1200 mm centre to centre, to which the ceiling section 0.5 mm thick bottom wedge of 80 mm with tapered flanges of 26 mm each having lips of 10.5 mm, at 450 mm centre to centre, shall be fixed in a direction perpendicular to G.I. intermediate channel with connecting clips made out of 2.64 mm dia x 230 mm long G.I. wire at every junction, including fixing perimeter channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the perimeter of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and perimeter channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound , jointing tapes , finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of perimeter channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with : 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- (Part I) : 2011 (Board with BIS certification marks)

Providing and fixing GI Clip in MTR.al Ceiling System of 600x600 mm module which includes providing and fixing 'C' wall angle of size 20x30x20 mm made of 0.5 mm thick pre painted steel along the periMTR.er of the room with help of nylon sleeves and wooden screws at 300 mm center to centre, suspending the main C carrier of size 10x38x10 mm made of G.I steel 0.7 mm thick from the soffit with help of soffit cleat 37x27x25x1.6 mm, rawl plugs of size 38x12 mm and C carrier suspension clip and main carrier bracket at 1000 mm c/c. Inverted triangle shaped Spring Tee having height of 24 mm and width of 34 mm made of GI steel 0.45 mm thick is then fixed to the main C carrier and in direction perpendicular to it at 600 mm centers with help of suspension brackets. Wherever the main C carrier and spring T have to join, C carrier and spring T connectors have to be used. including fixing periMTR.er channels 0.5 mm thick 27 mm high having flanges of 20 mm and 30 mm long, the periMTR.er of ceiling fixed to wall/partition with the help of rawl plugs at 450 mm centre, with 25mm long dry wall screws @ 230 mm interval, including fixing of gypsum board to ceiling section and periMTR.er channel with the help of dry wall screws of size 3.5 x 25 mm at 230 mm c/c, including jointing and finishing to a flush finish of tapered and square edges of the board with recommended jointing compound, jointing tapes, finishing with jointing compound in 3 layers covering upto 150 mm on both sides of joint and two coats of primer suitable for board, all as per manufacturer's specification and also including the cost of making openings for light fittings, grills, diffusers, cutouts made with frame of periMTR.er channels suitably fixed, all complete as per drawings, specification and direction of the Engineer in Charge but excluding the cost of painting with: 12.5 mm thick tapered edge gypsum plain board conforming to IS: 2095- Part I. All sections to be galvanized @ 120 gms/SQM (both side inclusive), fixing with clip in tiles into spring 'T' with: GI MTR.al Ceiling Clip in plain Beveled edge global white color tiles of size 600x600 and 0.5 mm thick with 25 mm height, made of G I sheet having galvanizing of 100 gms/ SQM (both sides inclusive) and 20% perforation area with 1.8 mm dia holes and having NRC of 0.5, electro statically polyester powder coated of thickness 60 microns (minimum), including factory painted after bending and perforation.

Providing and fixing Armstrong Vertical Linear Baffle Ceiling made out of Aluminum Extrusion in Aluminum alloy grade 6063. The baffle blade shall be in size of 100x 25 x 3600mm in finish as/ spec – Pradoo & Cabrueava. The baffle blade shall be suspended using Slotted U-profile at on-center spacing in multiples of 200 c/cmm. Longer lengths of Baffle to be connected by Baffle Joiner and the ends to be fixed with End caps. Installation of U-Grid:The U profile to be suspended at every 1200mm on-centre using 6mm threaded rod from the structural soffit using U-profile hanger. U-profile splice to be used to join more than one U profiles of length 3.75M. 1st U-Grid Channel must be no more than 400mm from the perimeter. Installation of Armstrong Baffles: Locate the slot for Baffle Hangers in slot of Baffle section at 1200mm centres. Hangers are inserted into the slot, then rotated 90° and fixed into position by tightening the grub screw. Baffle to be lifted into position and hangers engage over lip of U-Grid Channel. Each Hanger to be secured into position by inserting the Locking Clip. Baffles blades to be connected at ends with Baffle Joiner, which are inserted into the top and bottom slots of the Baffle closed profile for alignment only. The bottom Joiner to be located first and fastened on one side only. The top Joiner to be fitted then and secured with grub screws on one side. Then the two Baffle sections shall be joined and the top Joiner is screw fastened on the 2nd Baffle profile.End Caps to be located by pushing the End Cap tongues into Baffle slots.Installation shall be according to the instructions provided by manufacturer.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

SUB-STATION

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Treatment of soil under existing floors using chemical emulsion @ one litre per hole, 300 mm apart including drilling 12 mm diaMTR.er holes and plugging with cement mortar 1:2 (1 cement : 2 Coarse sand) to match the existing floor With Chlorpyriphos/Lindane E.C. 20% with 1% concentration

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Extra for additional height in centering, shuttering where ever required with adequate bracing, propping etc., including cost of de-shuttering and decentering at all levels, over a height of 3.5 m, for every additional height of 1 MTR.re or part thereof (Plan area to be measured). Suspended floors, roofs, landing, beams and balconies (Plan area to be measured)

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete.

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing average 150 mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/l.

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Providing and fixing SS finished tower bolts (600 x 23 x 40 MM 680 Grams) with with necessary screws, etc. all complete & instructionof Engineer in charge. 5 year warranty , Make Aquieen or equivalent , Material SS , Model No. TB651)

Providing and fixing Godrej Locks C071 2 Speed Hydraulic 60kg Door Closer (Silver) body tubular type universal hydraulic door closer (Mounting on door panel or door frame ; Type: Lock ; Maximum Closing Moment: 14Nm ; Other Dimensions: Door Weight : 60 kg, Door Panel Width : 1050 mm, Door Opening Angle : 180°), with double speed adjustment with necessary accessories and screws etc.all complete & instructionof Engineer in charge. 1 Year warranty, Make Godrej , Material Silver , Model Locks C071 2 Speed

Melamine polishing on wood work (one or more coat).

Fencing with angle iron post placed at required distance embedded in cement concrete blocks, every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and provided with horizontal lines and two diagonals interwoven with horizontal wires, of barbed wire weighing 9.38 kg per 100 m (minimum), between the two posts fitted and fixed with G.I. staples, turn buckles etc. complete. (Cost of posts, struts, earth work and concrete work to be paid for separately). Payment to be made per metre cost of total length of barbed wire used.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coating and cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification of seepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entire treated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coat should be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entire treated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added in screed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc.

For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filled with polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mm to 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in charge Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats

Providing two coat of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface throughly , scaffolding and taxes all after removing dirt including scales smokes, grease and sand papering including cost of scaffolding and taxes all complete as per building specification and direction of E/I.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

UNDER GROUND TANK

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing coarse clean local SAND IN FILLING in foundation trenches or in plinth including ramming and watering in layer not exceeding 150 mm thick with all leads and 1.5 M lifts including cost of all materials, labours, royalty and taxes all complete as per building specification and direction of Engineer In charge

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for Walls (any thickness) including attached pilasters, butteresses, plinth and string courses etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Retaining Wall :- Providing and laying of minimum 1.5 mm thick SBS modified self adhesive waterproofing membrane topped with cross laminated HDPE valeron film, Dr. Fixit Samshield XL1500, having tensile strength of 3.5 N/mm2 and with minimum elongation (L/T) of 180% (as per ASTM D 882). The membrane shall have puncture resistance of >200 N (as per ASTM D 412 -06). The system includes base preparation of cleaning, brushing and removal of flacky materials, grouting the porous area with cementitious grout, proper coving between slab and wall junctions and priming the surface with cold applied bituminous primer, Dr. Fixit Torchshield primer (or equivalent), followed by installation of waterproofing membrane. The SBS membrane should be sealed properly at joints & maintaining 75 mm overlap between the membrane selvedge & 100 mm overlap on the end joints of the membrane over the surface etc. a) Providing protection board of geodrain boad of 10mm thick fixed on to the membrane complete as per the specification and drawing. The waterproofing system should be applied by the manufacturer approved partner applicator with 10 years of warranty against leakage. Products made in India will be given preference.All vertical surfaces will be fixed using prefixed gaskets etc. complete as per manufactures specification.

Termination at vertical: - 3) Use a C- Shaped aluminium flashing strip or tuck it into a concrete wall of a groove of 12mmx12mm .T he aluminium flashing can be fitted to press the membrane into the groove and then be filled with a single component Dr. fixit PU sealant .

Provinding and fixing UPVC Foot rest all complete

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

BARRACKS FOR MINISTER BUNGALOW

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Earth filling in foundation trenches and plinth in layer not exceeding 150mm thick will watered rammed fully compacted and fine dressed with earth obtained from excavation of foundation trenched with a lead of 50mm and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

All works above plinth level upto floor V level

Add for using extra cement in the items of design mix over and above the specified cement content therein.

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for :Columns, Pillars, Piers, Abutments, Posts and Struts

Add for plaster drip course/ groove in plastered surface or moulding to R.C.C. projections.

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing designation 100 A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:6) in foundation and plinth with approved uality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with flyash lime brick (FLAG) in (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Extra for brick work for each consecutive floor above first floor including watering & scaffolding all complete as per direction of E/I

Extra for providing & placing in position 2 no 6mm dia ms bar every 3rd corse of half brick masonary

Providing and laying Doublecharge vitrified floor tiles in different sizes (thickness to be specified by the manufacturer )with water absorption less than 0.08% and conforming to IS:15622 / ISO 13006 of approved make , in all colurs and shades, laid on 20mm thick cement mortor 1:4 (1 cement : 4 coarse sand), jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with white cement and matching pigments etc., complete Size of Tile 600mm x 600mm

Providing and laying 25mm thick kotah stone slab flooring of approved size texure and colour over 19mm thick base of lime mortar (1:1:1) (limeputty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick kotah stone tiles in risers of steps skirting and pillars of approved size texure and colour laid over 12mm thick cement mortar (1;30 and joined with grey cement slurry mixed with pigment to match the shade of the slab including rub bing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing and fixing granite 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for flooring, kitchen platforms, vanity counters, window sills , facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels.

Providing edge moulding to 18 mm thick marble/granite stone counters, Vanities etc., including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge.Granite work

Extra for providing opening of required size & shape for wash basin/ kitchen sink in kitchen platform, vanity counter and similar location in marble/ Granite/stone work, including necessary holes for pillar taps etc. including moulding, rubbing and polishing of cut edges etc. complete.

Mirror polishing on marble work/Granite work/stone work where ever required to give high gloss finish complete.

Providing and laying Ceramic glazed floor tiles of size 300x300 mm (thickness to be specified by the manufacturer) of 1st quality conforming to IS : 15622 of approved make in colours such as White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick cement mortar 1:4 (1 Cement : 4 Coarse sand), including pointing the joints with white cement and matching pigment etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Finishing walls with water proofing cement paint of required shade :New work (Two or more coats applied @ 3.84 kg/10 SQM) SQM 57.85

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Wall painting with acrylic emulsion paint, having VOC (Volatile Organic Compound ) content less than 50 grams/ litre, of approved brand and manufacture, including applying additional coats wherever required, to achieve even shade and colour.Two coats

Supplying, fitting and fixing good quality well dressed and well seasoned teak wood work in chaukhats in doors, windows, skylight, fanlights and celetial windows openings, including wedge over clamps all complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/l

Providing and fixing factory made uPVC door frame made of uPVC extruded sections having an overall dimension as below (tolerance ±1mm), with wall thickness 2.0 mm (± 0.2 mm), corners of the door frame to be Jointed with galvanized brackets and stainless steel screws, joints mitred and Plastic welded. The hinge side vertical of the frames reinforced by galvanized M.S. tube of size 19 X 19 mm and 1mm (± 0.1 mm) wall thickness and 3 nos. stainless steel hinges fixed to the frame complete as per manufacturer’s specification and direction of Engineerin-charge Extruded section profile size 48x40 mm

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Providing and fixing to existing door frames.: - 30 mm thick factory made Polyvinyl Chloride (PVC) door shutter made of styles and rails of a uPVC hollow section of size 60x30 mm and wall thickness 2 mm (± 0.2 mm), with inbuilt decorative moulding edging on one side. The styles and rails mitred and joint at the corners by means of M.S. galvanised/ plastic brackets of size 75x220 mm having wall thickness 1.0 mm and stainless steel screws. The styles of the shutter reinforced by inserting galvanised M.S. tube of size 25x20 mm and 1 mm (± 0.1 mm) wall thickness. The lock rail made up of 'H' section, a uPVC hollow section of size 100x30 mm and 2 mm (± 0.2 mm) wall thickness fixed to the shutter styles by means of plastic/ galvanised M.S. 'U' cleats The shutter frame filled with a uPVC multi-chambered single panel of size not less than 620 mm, having over all thickness of 20 mm and 1 mm (± 0.1 mm) wall thickness . The panels filled vertically and tie bar at two places by inserting horizontally 6 mm galvanised M.S. rod and fastened with nuts and washers, complete as per manufacturer's specification and direction of Engineer-in-charge.

Extra for providing lipping with 2nd class teak wood battens 25 mm minimum depth on all edges of flush door shutters (over all area of door shutter to be measured).

Extra for cutting rebate in flush door shutters (Total area of the shutter to be measured).

Providing and fixing wooden moulded beading to door and window frames with iron screws, plugs and priming coat on unexposed surface etc. complete : 50x12 mm

Providing, fitting and fixing oxidised iron fitting of approved quality and make to door and window all complete as per building specification and direction of E/I necessary screws etc. complete. 300 mm sliding door bolt

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Providing and fixing bright finished 100 mm mortice lock with 6 levers without pair of handles of approved quality for aluminium door, with necessary screws etc complete as per direction of Engineerin-charge.

Providing and fixing aluminium hanging floor door stopper, ISI marked, anodised (anodic coating not less than grade AC 10 as per IS : 1868) transparent or dyed to required colour and shade, with necessary screws etc. complete.Twin rubber stopper

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Melamine polishing on wood work (two or more coat).

Providing gola 75x75 mm in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 stone aggregate 10 mm and down gauge), including finishing with cement mortar 1:3 (1 cement : 3 fine sand) as per standard design : In 75x75 mm deep chase

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

WATERPRROFING FOR OLD AND NEW ROOF SLAB : Providing and laying waterproofing treatment on Roof Slab by applying two component factory designed ,ready to use ,acrylic modified flexible material applied with brush ,roller, or spray for waterproofing coating caoting as per manufacturer specification and following steps surface praparation : Providing nd cleaning of concree surfase to remove the dust oil,grease including removal of existing loose paint/ coating and cement laitance by cleanning with compressed air and water jet including all materials ,laobour tools complete .Pondig test to be done after plugging all outlets and to checked from soffit to identify seepage ,leakage . on identification of seepage ,cement grouting to be done with non shrink expanding admixture of SIKA INDIA PVT Ltd /MYK Schomburg /Dr.Fixit/fosroc or equivalent . providing and Repairing of all corners and joints such as those between the parapet wall and the roof slab etc shall be campererd with 150 mmx150 mm fillet of mortor (Cement :sand-1:4) Admixed with acrylic polymer of Sika /Fosroc/MYK/Dr.Fixit damaged concreting base slab,dead cracks if any with an acrylic polymer modified repair mortor including coat of Bonding agent of the same with cement slurry including all material,labour,tools comlplete. b) Apply fisrt coat two component acrylic modified ,ready use ,flexible cementituous material on surface saturated dry roof and inside wall of paraphet wall upto 600 mm by brush or roller .After 1st coat of application ,45 GSM of fibre cloth to lay when fibre glass cloth when the first layer is still in green .1st coat to be applied @1.5kg/sqmt/coat. for the purpose of measurement entire treated surface will be maesured. c)2nd coat -To apply the 2nd coat of two component acrylic modified ready to use ,flexible cementituous material at right angle to the first coat over the glass fibre laid surface 2nd coat should be applied at @.7 kg /sqmtr /coat. for the purpose of measurement entire treated surface will be maesured.After three days of drying 2nd coat the rain water outlets to be plugged and ponding test to be done for 48 hrs to identify the seepage ,leakage from the sofit and if found necessary rectification to be done as per satisfaction of E/C. The waterproofing coating to protected from damage before screed over it.Waterproofing brand- Sika Topseal 109hi/Fosroc Brushbond RFX/Dr.Fixit Pidifin 2K/MYK Aquafin TG Product Prformance--Chemical Base part A Acrylic Polymer ,Part B ,Specially graded cementitious powder Density -1.6 Kg/l(mixed density) at 27 C .Tensile strength -2N/MM2 After 28 days (with fibre cloth )According to ASTM D2370),Pull out bond strength -2N/mm2(concrete failure )According to ISO 4624 Slant shear bond strength -4N/MM2(According to FIP 5.15)Elongation at break -35% without fibre cloth and 20% with fibre cloth (According to ASTM D2370) d) Protection of treated surface with PCC -The treated surface should be covered with 25mm/50MM PCC of M-20 Grade (1:1.5:3) with proper slope (1:20) towards the rain outlets in alternate pannel of 2mtrx2mtr keeping gap of between the pannel joint .Integral waterproofing admixture confirming to IS 2645 @ 100ML Per Bag of cement to be added in screed concrete (Paid seperately for this item) all corners to be champered with 150mmx150mm fillet .The Rain water oulets shall be just levelled with the screed to ensure smooth discharge of water -The pherperal gaps between PVC pipes oulet and concrete surface to be packed properly with moisture insensitive epoxy putty of Sika India Pvt Ltd/MYK Schomburg/Dr.Fixit/Fosroc.

For purpose of measurement the entire traeted surfaceto be measured. e) Goove of PCC -Surfcae should be filled with polysulphide sealent (paid Seperately) Brand -Sika India Pvt Ltd/MYK Schomburg /Dr.Fixit/Fosroc.Warranty 10 years Covering treated surface with PCC: Providing 50 MM thick cement concrete M20(1;1.5;3) Maintaining slope in alternate pannel 2mtx2mt pannels with approved quality stone chips 20mm to 6mm size graded and sand of F.M.2.5 to 3 including screening,shuttering and mixing cement concrete in mixer with admixture of integral waterproofing and placing position,striking,curing taxes ,loyality all complete as per specification and direction of E/I,Pannels that has been left should be casted next day ,There should be 6mm gap between the Pannels. Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing and mixing integral waterproofing compound in concrete or plaster as per manufacturer specification and as per direction of Eng in charge Brand-Sika plastocrete plus,/MYK Schomburg WP 10 /Dr.Fixit-Pidiproof lw+/Fosroc -Conplast X421IC or equivalent

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per specification and direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Applying one coat of water thinnable cement primer of approved brand and manufacture on wall surface Water thinnable cement primer

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Providing and fixing factory made uPVC white colour sliding glazed window upto 1.50 m in height dimension comprising of uPVC multi-chambered frame with in-built roller track and sash extruded profiles duly reinforcedwith 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), appropriate dimension of uPVC extruded glazing beads and uPVC extruded interlocks, EPDM gasket, wool pile, zinc alloy (white powder coated) touch locks with hook, zinc alloy body with single nylon rollers (weight bearing capacity to be 40 kg), G.I fasteners 100 x 8 mm size for fixing frame to finished wall and necessary stainless steel screws etc. Profile of frame & sash shall be mitred cut and fusion welded at all corners, including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealent over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes, wire mesh and silicon sealent shall be paid separately) Note: For uPVC frame and sash extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. Three track three panels sliding window with fly proof S.S wire mesh (Two nos. glazed & one no. wire mesh panels) made of (big series) frame 116 x 45 mm & sash 46 x 62 mm both having wall thickness of 2.3 ± 0.2 mm and single glazing bead / double glazing bead of appropriate dimension. (Area of window above 1.75 sqm).

Providing and fixing factory made uPVC white colour fixed glazed windows/ventilators comprising of uPVC multi-chambered frame and mullion (where ever required) extruded profiles duly reinforced with 1.60 ± 0.2 mm thick galvanized mild steel section made from roll forming process of required length (shape & size according to uPVC profile), uPVC extruded glazing beads of appropriate dimension, EPDM gasket, G.I fasteners 100 x 8 mm size for fixing frame to finished wall, plastic packers, plastic caps and necessary stainless steel screws etc. Profile of frame shall be mitred cut and fusion welded at all corners, mullion (if required) shall be also fusion welded including drilling of holes for fixing hardware's and drainage of water etc. After fixing frame the gap between frame and adjacent finished wall shall be filled with weather proof silicon sealant over backer rod of required size and of approved quality, all complete as per approved drawing & direction of Engineer-in-Charge. (Single / double glass panes and silicon sealant shall be paid separately). Note: For uPVC frame, sash and mullion extruded profiles minus 5% tolerance in dimension i.e. in depth & width of profile shall be acceptable. Variation in profile dimension in higher side shall be accepted but no extra payment on this account shall be made. 9.147B.1 Fixed window / ventilator made of (small series) frame 47 x 50 mm & mullion 47 x 68 mm both having wall thickness of 1.9 ± 0.2 mm and single glazing bead of appropriate dimension. (Area upto 0.75 sqm.)

Providing, assembling and supplying vision glass panels (IGUs) comprising of herMTR.ically-sealed 6-12- 6 mm insulated glass (double glazed) vision panel units of size and shape as required and specified, comprising of an outer heat strengthened float glass 6mm thick, of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade, an inner Heat strengthned clear float glass 6mm thick, spacer tube 12mm wide, dessicants, including primary seal and secondary seal (structural silicone sealant) etc. all complete for the required performances, as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineer-in-Charge. The IGUs shall be assembled in the factory/ workshop of the glass processor. (Payment for fixing of IGU Panels in the curtain glazing is included in cost of item No.26.2) For payment, only the actual area of glass on face # 1 of the glass panels (excluding the areas of the grooves and weather silicone sealant) provided and fixed in position, shall be measured in SQM. (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, + 12mm Airgap + 6mm Heat Strengthened clear Glass of approved make having properties as visible Light transmittance (VLT) of 25 to 35 %, Light reflection internal 10 to 15%, light reflection external 10 to 20 %, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/SQM degree K etc. The properties of performance glass shall be decided by technical sanctioning authority as per the site requirement.

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

INTERNAL ROAD AND LANDSCAPE

Earth Work in excavation in Foundation Trenches in Ordinary soil (vide classification of soil item -B) and disposal of excavated earth as obtained to a distance upto 50 M including all lift, leveling ramming the foundation trenches, removing roots of tree shrubs all complete as per approved design, building specification and direction of E/I

water bond macadam: - Providing, laying spreading & compacting stone aggregates of specific size to water bond macadam specification including spreading in uniform thickness hand packing, rolling with vibratory roller 8-10 tone / smothery wheeled steel roller in stages to proper gate & chamber, applying and booming requisite type of screening / binding materials to fill up the interstices of course aggregate, water and compacting to the required density. (B) By mechanical means : - (b) Using screening Type - A (13.2mm Agg.) with vibratory roller.

Providing P.C.C. (1:3:6) in foundation (Plain cement concrete 1:3:6 nominal mix in foundation with crushed stone aggregate 40 mm nominal size mechanically mixed , placed in foundation and compacted by vibrating curing, for 14 days.)nas per building specification and direction of Engineer-in-charge.

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing )

Providing and laying in position ready mixed M-25 grade concrete for reinforced cement concrete work, using fly ash and cement content as per approved design mix, and manufactured in fully automatic batching plant and transported to site of work in transit mixer for all leads, having continuous agitated mixer, manufactured as per mix design of specified grade for reinforced cement concrete work, including pumping of R.M.C. from transit mixer to site of laying, excluding the cost of centering, shuttering, finishing and reinforcement, including cost of admixtures in recommended proportions as per IS : 9103 to accelerate / retard setting of concrete, improve workability without impairing strength and durability as per direction of the Engineer - in - charge. NOTE- (1) Cement content considered in this item is @ 330 kg/cum. Excess/ less cement used as per design mix is payable/ recoverable separately.

All works upto plinth level

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Providing Tor steel reinforcement of 8mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 10mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing Tor steel reinforcement of 12mm. to 32mm. dia. rods as per approved design and drawing excluding carriage of M.S. bars to work site , cutting, bending and binding with annealed wire with cost of wire, removal of rust placing the rods in position all complete as per building specification and direction of E/l. (TMT Fe 500 (only vailid for TATA (TISCON), SAIL, JSPL, Electro steel Limited Bokaro and Vizal steel(RINL))

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing and laying 25mm thick. Kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (lime putty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royality all complete as per building specification and direction of E/I. 600 x 600 mm size

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/SQM including pointing in white cement complete. Granite of any colour and shade

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Providing and laying 6mm thick mosaic flooring of approved texture and colour over 25 mm thick P.C.C. (1:2:4) base with 10 mm down stone chips and sand of F.M. 2.5 to 3 rubbed and polished to granolilthic finish with approved quality of carborandum stone, top layer of 6 mm. being laid with 4 mm and down marble chips of approved quality and shade in ratio (1:2) cement and marble dust mixed in ratio of (3:1) by weight of marble chips including casting in approved block, curing, taxes and royalty all complete as per building specification and direction of E/l. (b) With 100% white cement with Dehradun marble chips & Daltonganj marble dust

Providing and laying 6mm thick mosaic in skirting , dado, steps and pillars of approved texture and colour over 12mm thick cement plaster (1:3) base with sand of F.M. 1.5 rubbed and polished to granolithic finish with approved quality of carborandum stone top layer of 6mm being laid with 4mm and down marble chips of approved quality and shade in ratio (1:2) cement and marble dust mixed in ratio (3:1) by weight of marble chips including cost of curing, royalty and taxes all complete as per building specification and direction of E/l. (b) With 100% white cement

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408) B. Using Concrete Batching and Mixing Plant

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing average 150 mm thick dry rammed khoa beaten to 112 mm (compacted with water) made of well burnt jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/l.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

18 mm cement plaster in two coats under layer 12 mm thick cement plaster 1:5 (1 cement : 5 coarse sand) finished with a top layer 6 mm thick cement plaster 1:6 (1 cement : 6 fine sand).

Finishing walls with textured exterior paint of required shade : New work (Two or more coats applied @ 3.28 ltr/10 SQM) over and including priming coat of exterior primer applied @ 2.20kg/10 SQM

Providing, fixing and erecting tensile structure with type ‘zero’ PVDS 650 GSM fabric (origin- Germany/Belgium) fixed on Duco painted MS Structure erected on existing roof structure including any water proofing work required to apply on the raw RCC roof slab to complete as per approved design. ( 30% fabric area to be taken extra for conical shape)

Light Fixture

Street Light Mounted on 9M High Pole

Wall Mounted Street Light

Post Top Light

Uplighter

Ceiling Hung Light

Submerged Uplighter

Bollard

Wall mounted Up down light

boundary wall lamp

CARRAIGE OF MATERIALS

CEMENT ( 5KM )

SAND ( 36KM )

CHIPS ( 18 KM )

METAL ( 18KM )

STEEL ( 5KM )

BRICKS ( 32KM )

WATER SUPPLY AND SANITATION WORK

Supplying, fitting and fixing 40mm high vitreous white glazed earthen E.W.C. with ‘p’ trap of parry hindustan or any other approved I.S.S. make including supplying and fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I.handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450grams 15mm P.V.C. alkathene pipe 45cm. long with brass coupling at both ends and white/black plastic solid state seal and lead of commander/cuckoo or other I.S.S. make with hinges or screws etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide priming, all complete as per specification and direction of E/I. (ii) E.W.C. with 'S' trap. (a) 12.5 lit low level PVC Cistem

Providing and fixing of white vitreous china wall hung / floor mounted European type water closet of approved shape and size with inside glazed P trap, with concealed flushing cistern dual flush capacity of 2.1 / 4.2 LPF including soft close anti-bacterial seat & cover infused with nano silver ions (AG+) for 99.9% bacteria protection along with hinges & rubber buffers, CP brass screw, washer with all associated accessories with side gap filled with silicon sealant wherever required complete including cutting and making good the walls, floors, slab wherever required complete. Wall Hung WC with seat cover Make Kohler Model No K-18131IN-S-0 / + Concealed Flushing Cistern Make Kohler Model No K-P77027IN-M-NA+ Face Plate for Cistern Make Kohler Model No K-4177IN-M-CP / + W.C Pan Connector Make Kohler Model No K-1036902

Providing and fixing white vitreous china wash basin of approved shape and size with special fabricated brackets duly painted white, faucets as required, 32 mm C.P. brass waste.32 mm C.P. brass bottle trap & pipe to wall with rubber adopter for waste connection and C.P. brass wall flange complete in all respects including cutting and making good the walls where required. Under Counter Wash basin Make Kohler Model No K-2215IN-0 , 32 mm CP brass waste Make Kohler Model No K-45433IN-CP, 32 mm C.P. brass bottle trap with pipe to wall and C.P. wall flange Make Kohler Model No K-7314IN-CP.

Supplying fitting and fixing vitreous white glazed earthen ware wash hand basin of parry or Hindustan or any other I.S.S. approved make supported on painted C.I. or R.S. brackets 32mm C.I.brass waste, 15 mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grams, 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/I.

Supplying fitting and fixing white glazed fire’s clay sink of approved make with overflow arrangements supported on C.I. or R.S. painted brackets 40mm. dia C.P.brass waste with C.P.brass chain and rubber plug 40 mm dia P.V.C. waste pipe about 750mm long with brass coupling at one endand 15mm C.I. body brass spindle bib cock of approved quality of weight not less than 450grams. including cutting wall and making good the same etc. all complete as per specification and direction of E/I. Kitchen sink 600mm ×450mm×250mm.

Providing & fixing PVC waste pipe for sink including PVC waste fitting Complete. Flexible Pipe, 32mm Dia.

Providing and fixing c.p. brass basin mixer complete in all respects including cutting and making good the walls where required.

Providing and Fixing of C.P. Brass Shower set comprising of : One No. CP brass Single Lever Concealed Diverter Make Kohler Model No. K-16316IN-4FP-CP + K-8821IN-CP, One No. CP brass OH shower head & Shower Arm Make Kohler Model No.K-45429IN-A-CP, One No. CP brass Bath Spout Make Kohler Model No.K-99060IN-CP, Including cutting and making good the walls wherever required.

Providing and fixing PTMT Bottle Trap for Wash basin. Bottle trap 31 mm single piece moulded with height of 270 mm, effective length of tail pipe 260 mm from the centre of the waste coupling 77 mm breadth with 25 mm minimum water seal, weighing not less than 260 gms.

Providing & fixing PTMT towel ring trapezoidal shape 215 mm long 200 mm wide with minimum distance of 37 mm from wall face with concealed fittings arrangement of approved quality and colour weighing not less than 88 gms

Providing and fixing male ended 15mm dia brass bib cock of approved quality (Wt. not less than 350gms.) with extra socket all complete as per specification and direction of E/I.

Providing and fixing C.P. brass long body bib cock of approved quality conforming to IS standards and weighing not less than 690 gms. 15 mm nominal bore

Providing and fixing C.P. brass angle valve for basin mixer and geyser points of approved quality conforming to IS 8931 a) 15 mm nominal bore. 15 mm nominal bore

Providing and fixing toilet paper holder : C.P. brass

Providing and fixing lead connection pipe with heavy quality brass coupling 2 nos. at both ends etc all complete as per specification and direction of Engineer-in-charge. 15 mm dia and 45 cm long,

Providing and fixing 15 mm size CP brass pillar cock (Weight not less than 350gms) C I body brass spindle pillar cock of approved quality as per specification and directionof Engineer-in-Charge. C.I body brass spindle.

Supplying fitting and fixing the following items complete with all materials as per specification and directionof E/I. (a) Glass shelf with C P brass rail, (i) 600×125 mm glass shelf complete

(b) Mirrors of 6mm thick plate glass bevelled edge mirror including C.P. brass revolving fittings 3mm ply wood board and C.P. hinges to fix with mirror.

(I) 600 mm×450 mm size

(II) CP brass dish container madium quailty with screw and hinges etc

(c) (III) C P brass liquid soap container

Providing, Fixing, testing and commissioning of C.P. brass wall/counter mounted Single Lever sink mixer with C.P. wall flange, overhead swinging spout/goose neck complete as required and making good Including necessary wall cutting / chasing and making good, as required of make parryware diamond range or equivalent as per direction of Engineer in Charge. HINDWARE make - ELEMENT (Cat No. F360027) / Equivalent

Providing, Installing & fixing storage type water heater of approved shade with copper container, glasswool insulation,stove enamelled M.S jacket, thermostatically controlled inner heater with pilot neon lamps, 15mm inlet stop cock valve, on inlet connection, 15mm dia C.P flexible connection pipe in inlet & outlet suitable for working pressure of 8 kg/sqcm complete as required. ( Make - Parry Ware Product Code- C500339). Capacity 25 litres.

Supply and fixing HINDWARE make or equivalent Health Faucet with 8 mm dia, flexible tube with wall hook and Angle stop cock with wall flange . Etc all as directed by Engineer In-Charge.HINDWARE make Health Fauce - 1.25 Mtr. long (Cat No. F160013)/ Equivalent

Providing and Fixing in position Hindware make or equivalent CP Grab Bar with wall flanges 600 mm to wooden cleats with C.P. brass screws complete in all respects.

Supply and fixing HINDWARE make or equivalent Health Faucet with 8 mm dia, flexible tube with wall hook and Angle stop cock with wall flange . Etc all as directed by Engineer In-Charge.

Providing, Fixing, testing and commissioning of UPVC pipe SWR type 'B' conforms to IS : 13592-1992 with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint.

110 mm (OD) SWR Pipe

Providing, Fixing and laying cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm in bed and all around UPVC waste pipes under floor, including shuttering and necessary reinforcement etc. complete as required for: - 100 mm dia

Providing, Fixing, testing and commissioning of UPVC 'P' trap/floor trap/urinal trap of self cleansing design with or without horn conforming to IS : 14735-1999 including setting with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 hard stone ballast 20 mm nominal size) cutting and making good the walls & floors.

110 mm (OD) x 110 mm (OD)

Providing, Fixing, testing and commissioning of UPVC cleanout plug conforming to IS : 14735-1999 complete with all fitting; accessories and civil work.

Providing, Fixing, testing and commissioning of UPVC waste Pipe conforming to IS : 4985-2000 class IV (6 Kg/Sq.cm) including all moulding fittings conforming to IS : 7834 (Part-1 - Part -7) 1987 such as tees, bends, reducers, coupling, adopters etc. solvent welded joint as per manufacturer recommendation including cutting and making good the walls, floors, R.C.C. work etc. (For waste connection)

Providing, Fixing UPVC floor drain including all fitting and accessories fixed in cement mortar complete in all respect. 110 mm OD x 63 mm OD

Providing, Fixing, testing and commissioning of UPVC inlet fittings with maximum 3 inlets 40, 50 & 63 mm OD size UPVC sockets, fixed to CI/UPVC traps including solvent weld joint/rubber ring joint complete with all civil work.

Providing and fixing PTMT grating of approved quality, colour and make 125 mm nominal dia with 25 mm waste hole

Providing and fixing straight/offset type flexible single body push fit type WC Pan Connector with factory supplied spring loaded seal guard with integrated single mould sealing fins made of flexible EVA Body, including bush/adaptor for use with CI Pipe as supplied with Pan Connector (For European water closet).

Providing and fixing in position stainless steel cockroch trap consisting of 0.45 mm thick inner and outer cup and 1.00 mm thick top grating (Jali) with ring to be fixed inside C.I. or uPVC ‘P’ traps with cement concrete.

RAIN WATER DISPOSAL :

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complete.

Providing and fixing on wall face unplasticised - Rigid PVC rain water pipes confirming to IS : 13592 Type A including jointing with seal ring confirming to IS : 5382 leaving 10mm gap for thermal expansion and with all fittings such as bends, tees, elbow, 'Y', offset, cleaning pipe door, clamps and steel structural supports etc. including cutting the floors, walls and making good the same in cement concrete 1:2:4 & cement mortar 1:4. The wall thickness of pipe and technical characteristic conforms to IS : 13592-1992 type 'B'. The fitting dimension conforming to IS : 14735-1999. The jointing to be completed with rubber ring joint/solvent weld joint.

Providing and laying cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm thick in bed and all around UPVC pipes under floor, including shuttering and centering for: - 100 mm dia

Providing and laying cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm thick in bed and all around UPVC pipes under floor, including shuttering and centering for: - 150 mm dia

Providing and laying cement concrete 1:2:4 mix (1 cement :2 coarse sand :4 graded stone aggregate, 20 mm down gauge) 75 mm thick in bed and all around UPVC pipes under floor, including shuttering and centering for: - 200 mm dia

Providing and fixing to the inlet mouth of rain water pipe cast iron grating 15cm diameter and weighting not less than 440 grams.

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS:15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer-in-Charge. Concealed work,including cutting chases and making good the wall etc

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4

PN - 16 Pipe, 32 mm OD (SDR-7.4

Providing and fixing 3 layer PP-R (Poly propylene Random copolymer) pipes confirming to IS 15801, UV stabilized & anti - microbial fusion welded, having thermal stability for hot & cold water supply, including all PP - R plain & brass threaded polypropylene random fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes testing of joints complete as per direction of Engineer-in-Charge. Internal Exposed on walls.

PN - 16 Pipe, 20mm OD (SDR-7.4)

PN - 16 Pipe, 25mm OD (SDR-7.4)

PN - 16 Pipe, 32mm OD (SDR-7.4)

PN - 16 Pipe, 40mm OD (SDR-7.4)

PN - 10 Pipe, 50mm OD (SDR-11)

PN - 10 Pipe, 63 mm OD (SDR-11)

Providing and fixing PPR Unions

PPR Union 20 mm

PPR Union 25 mm

PPR Union 32 mm

PPR Union 40 mm

PPR Union 50 mm

PPR Union 63 mm

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 62.5 mm nominal OD

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes,having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 75 mm nominal inner dia Pipes

Thermal Insulation on CPVC Pipe Embedded in Wall: = Providing & fixing thermal insulation on hot water pipes a flexible electomeric foam of closed cells structure having thermal conductivity of 0.038 W/M.K at 40o C, water vapour permeability fire propagation including all accessories e.g. adhesive and ape on joint complete as per specification. All joints shall be sealed with adhesive & cotton tape.

15.9 mm (OD) [6mm thick insulation]

22.2 mm (OD) [6mm thick insulation]

28.6 mm (OD) [6mm thick insulation]

35 mm (OD) [6mm thick insulation]

42 mm (OD) [6mm thick insulation]

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(a) 15 mm dia wt not less than 300 gms

(a) 20mm dia wt not less than 400 gms

(a) 25 mm dia wt not less than 500 gms

(a) 32 mm dia wt not less than 700 gms

(a) 40 mm dia wt not less than 1kg

Providing and fixing forged brass auto air vent valve PN10 (10.00 Kg/cm2) rating including all fitting with ball valve & accessories. 15 mm dia

Solenoid/ Motorized Valves :: - Providing & Fixing of 3" BSP Solenoid Made Nylon Glass Filled with flow control which shall be normally closed 24 VAC 50/60 cycle solenoid actuated angle pattern design. The valve pressure rating shall not be less than 12 bar. The valve body shall be constructed of high-impact, weather-resistant Nylon Glass Filled with heavy duty diaphragm and stainless steel screws, fasteners and components. The valve shall have manual open/close control (internal bleed) for manual opening and closing of valve without electrically energizing the solenoid, manual bleed can be removed for " tamper proof" operation. The valve shall operate with minimum 24 VAC at 12.0 bar. The valve must open or close in less than 1 minute at 10.5 bar, and less than 30 seconds at 0.7 bar. The valve construction shall provide for all internal parts to be removable from the top of the valve without disturbing the valve installation. 25 MM Dia.

Butterfly Valves :: - Providing, fixing, testing & commissioning of wafer type cast iron butterfly valves conforming to BS 5155 & IS 13095 tested to 15 Kg/Sq.cm pressure for maximum working pressure of 10 bar (PN 10) including all fitting and accessories (Drain, water meter for OH Tank/Riser).

50 mm dia

80 mm dia

EXTERNAL WATER SUPPLY:

Excavating trenches of required width for pipes including excavation for sockets also including for cement concrete craddles, and dressing of sides, ramming of bottoms, depth up to 1.5m including getting out the excavated soil, and then returning the soil as required, in layers not exceeding 20 cm in depth including consolidating each deposited layer with minimum 95% by ramming, watering etc. and disposing off surplus excavated soil as directed, within a lead of 50 m. UPTO 1.5M Pipes, cables etc, not exceeding 80 mm dia.

Providing, laying and jointing glazed stoneware pipes class SP-1 with stiff mixture of cement mortar in the proportion of 1:1 (1 cement : 1 fine sand) including testing of joints etc. complete :

100mm dia

150mm dia

200mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) all-round S.W. pipes including bed concrete as per standard design :

100mm dia

150mm dia

Providing and fixing square-mouth S.W. gully trap class SP-1 complete with C.I. grating brick masonry chamber with water tight C.I. cover with frame of 300 x300 mm size (inside) the weight of cover to be not less than 4.50 kg and frame to be not less than 2.70 kg as per standard design:150 x 100 mm size P type With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry manhole in cement mortar 1:4 ( 1 cement : 4 coarse sand ) with R.C.C. top slab with 1:1.5:3 mix (1 cement : 1.5 coarse sand (zone- III) : 3 graded stone aggregate 20 mm nominal size), foundation concrete 1:4:8 mix (1 cement : 4 coarse sand (zone- III) : 8 graded stone aggregate 40 mm nominal size), inside plastering 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with floating coat of neat cement and making making channels in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement complete as per standard design : Inside size 90x80 cm and 45 cm deep including C.I. cover with frame (light duty) 455x610 mm internal dimensions, total weight of cover and frame to be not less than 38 kg (weight of cover 23 kg and weight of frame 15 kg) : With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Extra for depth for manholes : Size 90x80 cm With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

GARDEN HYDRANT SYSTEM :

Providing, laying, testing & commissioning of UPVC pressure pipes of 10Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (For garden hydrants). 32 mm OD

Providing, laying, testing & commissioning of UPVC pressure pipes of 10Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (For garden hydrants). 40 mm OD

Providing, laying, testing & commissioning of UPVC pressure pipes of 10Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (For garden hydrants). 63 mm OD

Providing, laying, testing & commissioning of UPVC pressure pipes of 10Kg/Sq.cm pressure rating class V (IS : 4985-2000) including fittings, tees, bends, clamps, coupling and adaptors supports, and jointing with solvent joint, testing and necessary earth work in excavation, backfilling, disposal of surplus earth with a lead upto 50m complete, compaction and consolidation including bed concrete (if required), sand bedding all around UPVC pipe & fittings and thrust blocks at bends as per standard design (For garden hydrants). 110 mm OD

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l. (a) 25 mm dia wt not less than 500 gms

Constructing masonry Chamber 30x30x50 cm inside, in brick work in cement mortar 1:4 (1 cement :4 coarse sand) for stop cock, with C. I. surface box 100x100 x75 mm (inside) with hinged cover fixed in cement concrete slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size), i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand : 10 graded stone aggregate 40mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Sluice Valve :- Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 80 mm dia

Sluice Valve :- Providing and fixing gun metal gate valve with C.I. wheel of approved quality (screwed end) : 25 mm dia

Providing and fixing enclosed type water meter (bulk type) conforming to IS : 2373 and tested by Municipal Board complete with bolts, nuts, rubber insertions etc. (The tail pieces if required will be paid separately) : 80 mm dia

Providing and fixing C.I. dirt box strainer for bulk type water meter with nuts, bolts, rubber insertions etc. complete conforming to IS : 2373 : 80 mm dia

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design : With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Providing and fixing C.I. double acting air valve of approved quality with bolts, nuts, rubber insertions etc. complete (The tail pieces, tapers etc if required will be paid separately) : 80mm dia

EXTERNAL SEWERAGE :

Constructing masonry Chamber 120x120x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep ( inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

STORM WATER DRAINAGE:

Earth work in excavation by mechanical means (Hydraulic excavator) / manual means in foundation trenches or drains (not exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 1.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m. All kinds of soil.

Earth Work in Excavation of required width for storm water drainage pipes including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil and then returning the soil as required in layer not exceeding 20 cms in depth including consolidating each deposited layers by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50 m for all kinds of soil. Pipes, exceeding 80 mm dia but not exceeding 300 mm dia.

Earth Work in Excavation of required width for storm water drainage pipes including excavation for sockets and dressing of sides, ramming of bottom depth upto 1.5 m including getting out the excavated soil and then returning the soil as required in layer not exceeding 20 cms in depth including consolidating each deposited layers by ramming, watering etc. and disposing of surplus excavated soil as directed within a lead of 50 m for all kinds of soil. Pipes, exceeding 300 mm dia but not exceeding 600 mm dia.

Extra for excavating trenches for pipes, cables etc in all kinds of soil for depth exceeding 1.5m, but not exceeding 3m. (Rate is over corresponding basic item for depth up to 1.5 metre Pipes, exceeding 80 mm dia but not exceeding 300 mm dia.

Filling available excavated earth (excluding rock) in trenches, plinth, sides of foundations etc. in layers not exceeding 20cm in depth,consolidating each deposited layer by ramming and watering, lead up to 50 m and lift upto 1.5 m.

12 mm cement plaster of mix : 1:4 (1 cement: 4 fine sand)

Providing, laying and jointing light duty non-pressure NP2 class S/S R.C.C. pipes with collars jointing with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including curing, testing of joints etc. 250 mm dia

Providing, laying and jointing light duty non-pressure NP2 class S/S R.C.C. pipes with collars jointing with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including curing, testing of joints etc. 300 mm dia

Providing, laying and jointing light duty non-pressure NP2 class S/S R.C.C. pipes with collars jointing with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including curing, testing of joints etc. 450 mm dia

Providing, laying and jointing light duty non-pressure NP2 class S/S R.C.C. pipes with collars jointing with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including curing, testing of joints etc. 600 mm dia

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 250 mm dia.

Providing and laying cement concrete 1:5:10 (1 cement : 5 coarse sand : 10 graded stone aggregate 40 mm nominal size) up to haunches of S.W. pipes including bed concrete as per standard design : 300 mm dia.

CATCH BASIN CHAMBER FOR STORM WATER:

Constructing brick masonry road gully chamber 50 x 45 x 60 cm unit brick of class designated 75 in cement mortar 1:4 (1 cement :4 coarse sand) including 500 x 450 mm precast RCC horizontal grating with frame complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying, installation, testing and commissioning of electric driven terrace pump suitable for automatic operation and consisting of following, complete in all respects, as required: (Terrace Pump). (a) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (b) Suitable HP Squirrel cage induction motor, TEFC, synchronous speed 1500 RPM, suitable for operation on 415 volts, 3 phase 50 Hz, AC supply with IP 55 protection for enclosure, horizontal foot mounted type with Class-'F' insulation, conforming to IS-325. (c) Horizontal type, multistage, centrifugal, split casing pump of cast iron body & bronze impeller with stainless steel shaft, mechanical seal conforming to IS 1520. (d) M.S. fabricated Common base plate, coupling, coupling guard, foundation bolts etc. as required. (e ) Suitable cement concrete foundation duly plastered with anti vibration pads. 450 lpm at 35 m Head

Constructing brick masonry circular type manhole 0.91 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement outside rough cement plaster 15 mm thick with CM 1:3 (1 cement:3 coarse sand), foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard design. With F.P.S. bricks class designation 75.

Extra depth for circular type manhole 0.91m Internal dia (at bottom) with beyond 0.91 m to 1.67m. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Constructing brick masonry circular manhole 1.22 m internal dia at bottom and 0.56m dia at top in cement mortar 1:4 (1 cement : 4 coarse sand), in side cement plaster 12 mm thick with cement mortar 1:3 (1 cement : 3 coarse sand) finished with a floating coat of neat cement, foundation concrete 1:3:6 mix (1 cement : 3 coarse sand : 6 graded stone aggregate 40 mm nominal size), and making necessary channel in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) finished with a floating coat of neat cement all complete as per standard design. 1.68 m deep with SFRC cover and frame (heavy duty HD-20 grade designation) 560 mm dia at top conforming to I.S. 12592, total weight of cover and frame to be not less than 182 kg fixed in cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) including centering shuttering all complete. (Excavation, foot rests and 12 mm thick cement plaster at the external surface shall be paid for separately). With F.P.S. bricks class designation 75.

Extra depth for circular type manhole 0.91m Internal dia (at bottom) with beyond1.68 m to 2.29. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

FIRE PROTECTION WORKS

Providing and fixing carbon-di-oxide type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 4.5 Kg.

Providing and fixing ABC Powder type fire extinguishers consisting of welded M.S. cylinderical body, squeeze lever discharge valve fitted with pressure indicating guage internal discharge tube 30 cms long high pressure discharge hose, discharge nozzle, suspension bracket conforming to IS:15683 finished externally with red enamel paint and fixed to wall with brackets complete with internal charge. Capacity 6.0 Kg.

Providing orange colour safety foot rest of minimum 6 mm thick plastic encapsulated as per IS : 10910 on 12 mm dia steel bar conforming to IS : 1786 having minimum cross section as 23 mm x 25 mm and over all minimum length 263 mm and width as 165 mm with minimum 112 mm space between protruded legs having 2 mm tread on top surface by ribbing or chequering besides necessary and adequate anchoring projections on tail length on 138 mm as per standard drawing and suitable to with stand the bend test and chemical resistance test as per specifications and having manufacture's permanent identification mark to be visible even after fixing, including fixing in manholes with 30 x 20 x 15 cm cement concrete block 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size) complete as per design.

Providing and fixing M.S fabricated epoxy coated(two layers) galvinised coating puddle flange comprising of 600 mm dia long M.S class 'C' pipe (screwed end up to 50 mm & flange for more than 50 mm dia) with 6 mm thick M.S plates of required size upto 150 mm dia & 7.1 mm thick mm plate for pipe dia above 150 mm dia including cutting holes in centre of plate, inserting pipe & making welded (Arc) joint complete. Same shall be installed with TEC welded joint in position with reinforcement bars of RCC tank wall/slab including making cutout in shuttering during concrete casting of tank of following diameter. (Location: underground/ overhead tanks.)

25 mm dia

32 mm dia

40 mm dia

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Providing and placing on terrace storage tank ISI : 12701 marked indicating the BIS License No. with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank [Sintex, Electroplast, Star, Lotus or equivalent having valid ISI license].

Providing and fixing G.I. Vent Pipe class 'B' (medium duty) for R.C.C water storage tanks comprising of 600 mm long vertical pipe, return bend with mosquito grating & cast brass perforated coupling including all associated civil work. 100 mm dia

Providing and fixing of mosquito overflow grating /Jali of the following diameters including all fitings & accessories :- 100 mm dia

Water Supply, Drainage Pumps & Water Treatment Equipments

Supply, installation, testing & commissioning of vertical inline multistage pumping set (Imported) with Stainless steel body, impeller, casing, shaft and C.I. base & head with mechanical seal, connected to a TEFC induction motor suitable for 415+/- 10% volts, 3 phase 50 cycles A.C. supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundations, 80x40 mm I section base plate bolted to cement concrete foundations complete.Vendor to submit performance curves and technical catalogue of the proposed model for review and information. Filter Feed Pump (Dom. Water) at Water Supply Pump Room : - Set of Two Pumps (1 Working+ 1 Standby), Capacity - 2.0 LPS, Head - 25 M., HP - 2.0 HP Approxi, Head - 25 M,

Irrigation Pump at STP Pump Room : - Set of Two Pumps (1 Working+ 1 Standby), Capacity - 4.0 LPS, Head - 40 M., HP - 5.0 HP Approxi.

Providing, installing, testing and commissining of fixed speed hydropneumatic system mounted on a common base plate comprising of vertical centrifugal pumping set with S.S body, stainless steel impeller and mechanical seal, shaft directly coupled to a TEFC induction motor suitable for 400/440 volts, 3 phase, 50 cycles AC supply with 150 mm dia pressure gauge with gunmetal isolation cock, vibration eliminating pads under foundation, one No. microprocessor based controller, one No.remote sensors, pressure transducers, sequence running cotroller, dry running Protection,motor control centre, necessary power and control cabling from MCC to pumps including required rating of MCB, one No. 100 litre capacity M.S diaphragam tank with interchangeable butyl rubber membrane,complete in all respects, including stainless steel grade 316 pipe suction and delivery headers and isolation/ control valves( ball valves/butterfly valves/ Nan return valves/ vibration eliminators etc as required) , power box, equipped with fuses/ isolators/circuit breakers as required.

Hyd. System for Domestic Water Supply at Water Supply Pump Room l - Set of Two Pumps (1 Working+ 1 Standby), Capacity - 2.5 LPS, Head - 45 M., HP - 3.0 HP Approxi.

Hyd. System for Flushing Water Supply at STP Pump Rm - Set of Two Pumps (1 Working+ 1 Standby), Capacity - 1.5 LPS, Head - 45 M., HP - 2.0 HP Approxi.

Supply, installing, testing and commissioning of submersible open impeller non-clog pumps with C.I.body and to TEFC submersible motor for 415 + 10% volts, 3 phase, 50 cycles A.C. power supply with mechanical seal, pump connector unit with rubber diaphragm and bend, vertical discharge pipe, guide pipe and chain in built level controller, sequence running controller, arrangement for both pumps together inacase of emenegency, audible hooter for failure or flooding, dry running Protection complete in all respects., painting, testing and commissioning complete with approved quality and make as required as per instruction of site incharge. (Pumps shall be installed in a set of two pumps One working and One standby). Basement & Pump Room Drainage Pumps: - (Pumps to be suitable to handle solids upto 30 mm size) Capacity - 4.0 LPS (Each), Head - 15 M., HP - 1.5 HP Approxi.

Supply Installation,Testing & Commissioning of vertical self supporting Filter fabricated from MS sheet as per IS: 2825, ((minimum thickness of shall 6 mm and dished end 8 mm)) pressure gauges, sample cock, GI class 'C' face piping, CI butterfly valves and all accessories , with initial charge of filter media including anthracite, painting inside with epoxy paint and outside with two coat of red oxide primer and two or more coat of synthetic enamel paint, testing and commissioning complete.

Dual Media Filter For Domestic Water Supply: Capacity - 7200 LPS, Filtration rate- 14000 LPH/Sqm, Filter dia approx. - 1000 MM, Working pressure: 3.0 Kg/sq cm. ,Test pressure : 4. 5 Kg/sq cm.

Activated Carbon Filter For Domestic Water Supply : Capacity - 7200 LPS, Filtration rate- 14000 LPH/Sqm, Filter dia approx. - 1000 MM, Working pressure: 3.0 Kg/sq cm. ,Test pressure : 4. 5 Kg/sq cm.

Supply Installation,Testing & Commissioning of metering pump type chemical doser with 100 lits. HDPE chemical grade solution tank,injection fitting assembly,suction and delivery hose upto the point of injection, capacity 0-6 lph, complete in all respects. Chlorination of Domestic Water.

For Water Supply Pump: - To start pump when water level is low in Domestic Water U.G. tank and shut off pump when Domestic Water U.G. tank is full. Also to stop when water level is low in raw water underground tank.

For Sump Pumps:: - To start pump when water level is high in sump and shut off pump when sump is empty. Both pumps are start when sump is over flowing.

Providing and fixing GI pipes complete (IS:1239 Heavy Class) with GI fittings and clamps including MS pipe supports, enamel paint as per specifications cutting and making good the walls etc. complete.

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Providing & fixing butterfly valve tested to a pressure not less than 25 Kg/Sq.cm. Including rubber gasket, 2 nos. Table-E flanges, nuts, bolts, washers & painting complete as required.

50 mm dia

65 mm dia

80 mm dia

100 mm dia

Providing & fixing dual plate CI wafer type check valve tested to a pressure of 25 Kg/sqcm. Including rubber gasket, 2 nos. table-E flanges, union, nuts, bolts, washers & painting complete as required.

50 mm dia

65 mm dia

80 mm dia

Providing and fixing resilient rubber neoprene lined style arch vibration eliminators suitable for raw water upto 45 deg.C. Temperature working pressure upto 25 Kg/Sqcm.

50 mm dia

65 mm dia

Providing and fixing heavy duty armoured cables 1.1 KVA grade including necessary support clamps at ceiling level and connection lugs complete in all respects.

Power cable Copper 3 core 10 sq.mm

Power cable Copper 3 core 6 sq.mm

Power cable Copper 3 core 4 sq.mm

Control cable copper 2 core 1.5 sq.mm

Providing and fixing CI Y type suction strainer with gunmetal or brass internal parts installed outside water tanks. 100 mm dia.

FIRE PROTECTION

Providing, laying, testing & commissioning of 'C' class heavy duty MS pipe conforming to IS 3589/IS 1239 including Welding, fittings like elbows, tees, flanges, tapers, nuts bolts, gaskets etc. and fixing the pipe on the wall/ceiling with suitable clamp/support frame and painting with two or more coats of synthetic enamel paint of required shade complete as required :

25 mm dia

40 mm dia

100 mm dia

Supplying and fixing single headed internal hydrant valve with instantaneous Gunmetal/Stainless Steel coupling of 63 mm dia with cast iron wheel ISI marked conforming to IS 5290 (Type -A) with blank Gunmetal/Stainless Steel cap and chain as required :. Single headed Stainless steel

Supplying, fixing, testing and commissioning of butterfly valve of PN 1.6 rating with bronze/gunmetal seat duly ISI marked complete with nuts, bolts, washers, gaskets conforming to IS 13095 of following sizes as required :

100 mm dia

Providing, installation, testing and commissioning of non-return valve of following sizes confirming to IS: 5312 complete with rubber gasket, GI bolts, nuts, washers etc.as required :

100mm dia

Providing, installation, testing and commissioning of stainless steel Y-strainer fabricated out of 1.6 mm thick stainless steel, Grade 304, sheet with 3 mm dia holes with stainless steel flange.. 100 mm dia

Supplying and fixing 63 mm dia, 15 m long RRL hose pipe with 63 mm dia male and female couplings duly bound with GI wire, rivets etc. conforming to IS 636 (type-A) as required :. Stainless Steel (Grade 304)

Supplying and fixing first-aid Hose Reel with MS construction spray painted in post office red, conforming to IS 884 complete with the following as required. 20 mm nominal internal dia water hose thermoplastic (Textile reinforced) type -2 as per IS: 12585. 20 mm nominal internal dia gun metal globe valve & nozzle. Drum and brackets for fixing the equipmets on wall. Connections from riser with 25 mm dia stop gun metal valve & M.S. Pipe and socket. . 30 m

Supplying & fixing 63 mm dia gun metal short branch pipe with 20 mm nominal internal diameter size nozzle conforming to IS 903 suitable for nstantaneous connection to interconnect hose pipe coupling as required :. Stainless Steel (Grade 304)

HORTICULTURE WORK

Ground preparation, grassing and plantation

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

PREPARATION WORKS: - Trenching in ordinary soil up to a depth of 60 cm including removal and stacking of serviceable materials and then disposing of surplus soil, by spreading and neatly levelling within a lead of 50 m and making up the trenched area to proper levels by filling with earth or earth mixed with sludge or / and manure before and after flooding trench with water (excluding cost of imported earth, sludge or manure)

Rough dressing the trenched ground including breaking clods

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m diameter and 1.2 m deep

Holes 90 cm diameter and 90 cm deep

Holes 60 cm diameter and 60 cm deep

Holes 45 cm diameter and 45 cm deep

Providing and stacking of Alstonia scholaris of height 150-165 cm. in bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Azadirachta indica ( Neem ) of height 120-130cm in big polybag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bauhinia purpurea (Kachnar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Callistemon lanceolatus of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia javanica of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Foxtail palm of ht. 240-270 cm bottom girth 35- 40 cm well developed in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Magnolia grandiflora of height 150-165 cm. in bigpoly bag of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Mangifera indica (Mango-grafted ) of height 60-75 cm. in big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Phyllanthus emblica (Amla) of height 150- cm. in Big HDPE Bag as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Plumeria rubra of height 120-150 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Saraca indica (Sita Ashok) of height 105-120 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Spathodea campanulata of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Terminalia arjuna of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and Stacking of Lemon grass of ht. 30cm with multi branches in Poly bag of size 20 cm. as per direction of the officer-in-charge.

Providing and displaying of Brassia Variegated having ht. 30 cm, well developed with fresh and healthy foliage in 20 cm size of Earthen pot/ Plastic pot & as per direction of the officer-in-charge.

Providing and displaying of Philodendron Burgundy mounted on moss stick 90 cm ht., well developed with full of fresh & healthy leaves from bottom to top in 25 cm size of Earthen pot/Plastic pot & as per direction of the officer-in-charge.

Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ficus panda of height 90-105 cm. with 10-12 branches and healthy foliage, well formed in cement pots of size 30 cm as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3- 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 90-105 cm. bushy in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Jatropha multifida (red colour) of height 60-75 cm. multibranched in p.bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Nyctanthes arbor-tristis (Hasingar) of ht. 90-105 cm in Earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Tecoma gaudichaudi of height 90-105 cm.,bushy in big size HDPE bag as per direction of the officer-in-charge.

Providing and stacking of Bignonia venusta (Golden shower) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum splendens of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and Displaying Bougainvillea named variety, Sobhra, Thima, Marry palmar, Cherry Blossom etc. well developed with fresh & healthy bushy in full bloom 75 to 90 cm ht. in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum inerme of ht. 20 cm to 30 cm multi branched in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and displaying of Paspalum notatum, well developed with fresh and healthy foliage as per direction of the officer-in-charge.

Providing and displaying ofZoysia matrella , well developed with fresh and healthy foliage as per direction of the officer-in-charge.

Providing and displaying of Quisqualis Indica, well developed with fresh and healthy foliage as per direction of the officer-in-charge.

Providing and stacking of White fountain grass as per direction of the officer-in-charge.

Providing and stacking ofTradescantia pallida as per direction of the officer-in-charge.

Providing and stacking of Syngonium podophyllum as per direction of the officer-in-charge.

Providing and stacking of Sprenger's asparagus as per direction of the officer-in-charge.

Providing and stacking of Monstera deliciosa as per direction of the officer-in-charge.

Providing and stacking of Lantana sellowiana as per direction of the officer-in-charge.

Providing and stacking of Elettaria cardamomum as per direction of the officer-in-charge.

Providing and stacking of Euphorbiaceae as per direction of the officer-in-charge.

Providing and stacking of Hymenocallis littoralis as per direction of the officer-in-charge.

Providing and stacking of Canna Indica as per direction of the officer-in-charge.

Providing and stacking of Canna Musaefolia as per direction of the officer-in-charge.

Providing and stacking of Chlorophytum comosum as per direction of the officer-in-charge.

Providing and stacking of Crassula ovata as per direction of the officer-in-charge.

Providing and stacking of Aralia elata 'Variegata' as per direction of the officer-in-charge.

Providing and stacking of Alternanthera red as per direction of the officer-in-charge.

Providing and stacking of Alpinia zrumbet as per direction of the officer-in-charge.

Providing and stacking of Artocarpus heterophyllus as per direction of the officer-in-charge.

Providing and stacking of Aegle marmelos as per direction of the officer-in-charge.

Providing and stacking of Syzygium cumini as per direction of the officer-in-charge.

Providing and stacking of Psidium guajava as per direction of the officer-in-charge.

Providing and stacking of Litchi chinensis as per direction of the officer-in-charge.

Providing and stacking of Areca catechu as per direction of the officer-in-charge.

Providing and stacking of Bismarckia nobilis as per direction of the officer-in-charge.

Providing and stacking of Cordyline australis as per direction of the officer-in-charge.

Providing and stacking of Cyrtostachys renda as per direction of the officer-in-charge.

Providing and stacking of Phoenix canariensis as per direction of the officer-in-charge.

Providing and stacking of Phoenix dactylifera as per direction of the officer-in-charge.

Providing and stacking of Washingtonia robusta as per direction of the officer-in-charge.

Providing and stacking of Buddha belly bamboo as per direction of the officer-in-charge.

Providing and stacking of Golden bamboo as per direction of the officer-in-charge.

Providing and stacking of Acalypha wilkensiana as per direction of the officer-in-charge.

Providing and stacking of Caesalpinia pulcherrima as per direction of the officer-in-charge.

Providing and stacking of Colocasia as per direction of the officer-in-charge.

Providing and stacking of codiaeum variegatum as per direction of the officer-in-charge.

Providing and stacking of Excoecaria bicolour as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina Starlight as per direction of the officer-in-charge.

Providing and stacking of Golden duranta as per direction of the officer-in-charge.

ELECTRICAL WORK

HT CABLE

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade 1.1KV but not exceeding 11 KV of size not exceeding 120 Sqmm but not exceeeding 400 Sqmm direct in Ground including excavation, sand cushioning, protective covering and refilling the trench etc as required. 3c x 240 sqmm

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of grade 1.1KV but not exceeding 11 KV of size not exceeding 120 Sqmm but not exceeeding 400 Sqmm in the existing RCC/ HUME/STONE WARE / METAL pipe as required. 3c x 240 sqmm

Supplying and making indoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240 sq. mm

Supplying and making outdoor cable end jointing with cast resin compound, including lugs and other jointing materials, for following size of 3 core, XLPE aluminium conductor cable of 11 KV grade as required : 240sq. mm

Supply of cable XLPE -PVC insulated PVC sheathed galvanised steel strip armoured electric power cable with aluminium conductor 11000 volt grade of size 3C X 240 sqmm.

Supply of LT Cables

3.5 core, 300 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3.5 core, 240 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3.5 core, 185 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3.5 core, 150 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3.5 core, 120 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3.5 core, 35 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4 core, 10 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

3C-6.0Sq. mm Copper Armoured cable

3C-4.0Sq. mm Copper Armoured cable

4C-6.0Sq. mm Copper Armoured cable

4C-4.0Sq. mm Copper Armoured cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ STONE WARE / METAL pipe/ Cable Trays as required.

Upto 35 sq. mm

Above 95 sq. mm and upto 185 sq. mm

Above 185 sq. mm and upto 400 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 300 sq. mm.

3.1/2 core 240 sq. mm.

3.1/2 core 185 sq. mm.

3.1/2 core 150 sq. mm.

3.1/2 core 120 sq. mm.

3.1/2 core 95 sq. mm.

3.1/2 core 70 sq. mm.

3.1/2 core 50 sq. mm.

3.1/2 core 35 sq. mm.

4core 10sq. mm.

4C-6.0Sq. mm

4C-4.0Sq. mm

Cable Trays

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.( Powder coated shall be of Siemens Grey Colour- RAL 7032)

900 mm width X 75 mm depth X 2.0 mm thickness

750 mm width X 75 mm depth X 2.0 mm thickness

600 mm width X 75 mm depth X 2.0 mm thickness

450 mm width X 50 mm depth X 2.0 mm thickness

300mm width X 50mm depth X 1.6 mm thickness

150mm width X 50mm depth X 1.6 mm thickness

11 KV SWITCHGEAR PANEL :

Supply, unloading, storing, handling, installation, testing and commissioning of 11 KV 350 MVA,indoor, horizontal isolation, horizontal, drawout, Vacuum circuit breakers, Three Panel switchboard fabricated out of minimum 2 mm thick CRCA sheet as per specification. The panel shall be complete with all accessories & cable termination boxes suitable for 1R x 3C x 300 sqmm XLPE for incoming & 1R x 3C x 300 sqmm each for outgoing.

All Meters shall be digital type & 0.5 accuracy class.

All Indicating lamps shall be LED type.

All C.T. / P.T. shall be cast resin.

The switchboard shall consist of :

Incoming & Outgoing :

One (1) No. incomer & Two (2) Nos. outgoing, equipped with the following :

11 KV, 630 Amps, 350 MVA, 18.4 kA Electrically operated horizontal draw out horizontal isolation Vacuum Circuit Breaker complete with anti pumping device, trip free features and 6NO + 6 NC directly breaker control aux. switch contacts.

TNC switch with lost motion device.

One (1) Set of 11 KV grade indoor surge arrestor as per specifications and as required..

One (1) Set of cast resin drawout type potential transformer mounted over separate withdrawable trolley with fuse in primary & secondary, ratio: - 11KV/1.732 / 60/1.732 volts, 100 VA burden per phase and accuracy class 0.5.

One (1) Set of cast resin, protection class 5P10, ratio 100/60/5-5A, 15VA current transformer for protection.

One (1) Set of cast resin, accuracy class-0.5, 15 VA, current transformer for instrumentation (C.T. ratio as above).

Triple pole IDMTL O/C and E/F relay (51 & 51N similar to CDG-31 of M/s ALSTOM or equivalent) complete. Two (2) outer elements connected for over current & middle element for earth fault protection.

Over current setting : 50% - 200%

Earth current setting : 10% - 40%

One (1) No. Digital Multifunction Meter, with RS-485 port suitable for measurement of voltage, current, Power factor, frequency, Power (KW, KVA, KVAR), Energy (KWH, KVAH, KVARH) and Harmonics (EM-6434 of Conzerv or equivalent).

24V DC Shunt Trip Coil.

240V AC 1 phase spring charging motor.

Set of phase indication lamps with (Red, Yellow and Blue) with control SPMCB.

Set of Red/Green indicating lamp for close & open position.

Amber indicating lamp for Auto Trip.

Clear indicating lamp for trip circuit healthy.

Mechanical ON/OFF/Trip indication.

Blue indicating lamp for spring charged.

Strip heater to prevent absorption of moisture.

Panel illumination lamp.

One (1) No. 24V, Power Pack of suitable back-up rating for indications, annunciations and trip coil operations as per specification and as required.

TNC switch with lost motion device.

Set of 15/5A, cast resin, protection class 5P10, 15VA current transformer for protection.

Set of 15/5A, cast resin, accuracy class-0.5, 15VA current transformer for instrumentation.

Triple pole IDMTL O/C and E/F relay with instantaneous high set over current and earth fault protection 50, 50N, 51 & 51 N (similar to CDG-61 of M/s AREVA or equivalent) having settings range.

IDMTL Setting :

Over current setting : 50% - 200%

Earth current setting : 10% - 40%

Instantaneous Setting :

Over current setting : 500% - 2000%

Earth current setting : 100% - 400%

Auxilary relay similar to VAA 33 of Areva or equivalent.

Four (4) Window, Audio / visual annunciation system complete with Transformer trouble & protection trip, LT breaker trip annunciation. It shall be possible to acknowledge the fault from remote, control room. Necessary provision to be left in the acknowledgement circuit for this purpose.

WTI Alarm

WTI Trip

REF Trip

HT Breaker Trip

240V, AC 1-phase spring charging motor.

24V DC shunt trip coil.

Set of Red/Green indicating lamp for close & open position.

Amber indicating lamp for Auto Trip.

Clear indicating lamp for trip circuit healthy.

Mechanical ON/OFF/Trip indication.

Blue indicating lamp for spring charged.

Panel illumation lamp ----- RATE

Strip heater to prevent absorption of moisture.

Service, isolation, test indication.

Earthing Switch.

Copper Bus Bars

HT Panel Complete as described above

11KV/433 VOLT TRANSFORMERS

Supply and installation testing & commisioning of 1000 kVA transformer step down outdoor type complete with standard fittings HT 11 KV 3 phase 4 wire copper wound, delta/star connected (vector group-DYn -11), On load Tapp Changer on HV side , oil immersed, naturally oil cooled (ONAN), Distribution transformer complete with following:-

Silica gel breather with connecting pipe and oil seal.

Air release plugs.

Pressure release device. Explosion vent, should be double diaphragm type.

150mm dial magnetic oil level gauge with low level alarm contact.

150 mm dial oil temperature indicator with maximum reading pointer and electrically separate contacts for trip and alarm.

150 mm dial winding temperature indicator with maximum reading pointer and electrically separate sets of contacts for trip and alarm.

Thermometer pockets.

Oil conservator with filter cap, drain plug and plain oil level gauge (with coloured prismatic front).

Double float Buchholz relay with gas release cock, shut-off valve on either side and separate sets of contacts for trip and alarm.

Sampling valve/ Filter valve with threaded adopted (top and bottom).

Drain valve with threaded adopted.

Jacking pads, handling and lifting lugs.

Cover lifting eyes.

Radiators (Detachable type).

Clamping devices.

Two grounding pads.

Remote tap changer control panel.( RTCC)

Weatherproof marshalling box for housing control equipment and terminal connections.

Rating and terminal marking plates.

LT Neutral bushing with 50x6 cu flat suitably supported

Outdoor HT cable box (Detachable type) suitable to terminate 3C-240 sq. mm 11kV HT cable.

LT side cable box suitable for 6 Nos. 3.5C x 300 Sq. mm Al Arm LT Cables

1000 KVA Transformer describe as per above

DG SETS

Supply, installation, testing and commissioning at 0.8 P.F. (lagging), aircooled radiator type diesel engine alternator set mounted on common base frame complete with accessories as per specification and layout, drawing with battery charger, battery and battery rack residential silencer, stainless steel bellows, 990 Ltrs. day fuel tank, spring loaded GERB cush pads, logic control panel, governor etc including Accoustic Enclosure suitable for outdoor installation complete as required as follows:

750 KVA DG Set

Battery & Battery Charger

Supply, installation, testing and commissioning of 180 AH capacity 24 volts DC lead acid tubler battery..

Supply, installation, testing and commissioning of SMPS battery charger unit with provisions of Boost Charging, and Float charging. Suitable for 240 V, including DC DB single phase AC 50 Hz as per requirement.

Supply, laying of following sizes of MS Piping for Exhaust including providing suitable bends, reducers & supporting arrangement at suitable intervals including insulation on entire length of exhaust pipe with 75mm thick Rockwool insulation & painting etc. as required.

350mm (NB) MS ERW pipe

SUB-HEAD III: 415V LT PANELS

Design, fabrication, assembling, wiring & supply, installation, testing & commissioning of MV Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA painted sheet steel in cubicle formation with reinforcement of suitable size angle iron, channels, T irons, flats wherever necessary for large meter boards. Cable gland plates shall be provided at top and bottom both and windows for meter reading, locking arrangement (pad-lock & seal) with wiring upto KWH meter & meter to MCB shall be done by using adequately rated flexible single core copper wire. The boards shall be treated with all anticorrosive process before painting as per standards with final approved shade of powder coated as approved, 2 nos. earthing terminals shall be provided for all panels. The boards shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system. Boards shall be fabricated in length, height, depth etc to match with site conditions.

An approval shall be taken for each panel before manufacturing. Galvanised hardwares with zinc passivation shall be used in fabrication of boards.

Note: The following provisions shall be required to be made in the switchboard detailed below

The Switchboard shall have provision for entry of all PVCA cables/bus duct from the top/bottom as required.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbar insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used.

Suitable tinned copper extension links for incoming/outgoing cables shall be provided wherever required

Positive isolation of all breakers.

All fault level breaking capacity indicates shall be IC.S value at 415 volts (ICS = ICU = ICW = 100%).

Space Heater/ light/air filter shall be provided for each vertical compartment

Padlocking facility shall be provided on all outgoing feeders.

All ACB’s shall have all standard accessories such as CT’s, Arc Chute, Safety Shutters etc.

All inter Panel wiring from PLC to DG / Transformer / Bus Couplers as required.

Link and drops from ACB/MCCB shall be designed for full rated current of ACB/MCCB ratings at same current density as of Main Bus Bar

2 nos. GI earth strip throughout the panel.

MAIN LT PANEL MP-1 & MP-2 (50 kA)

INCOMING :-

2 Nos.1600 amps 4P electrically operated fully drawout type air circuit breaker as per specification and with following accessories. Transformer Supply Feeder-1 & 2

2 Nos.1250 amps 4P electrically operated fully drawout type air circuit breaker as per specification and with following accessories. DG Supply Feeder-1 &2

Metering & indication for Transformer Supply incoming breaker:

Breaker shall be provided with :

One(1) No. multifunction meter (MFM-1) with Rs- 485 port suitable for measurement of voltage, current, power factor, frequency, Power (kW,kVA, kVAR), Energy (kWH, KVAH, KVARH) and Harmonics (EM-6400 of Conzerv or equivalent).

One (1) set 3 Nos. CTs of ratio 1600/5A,15VA, Class 1.0 as required.

One (1) set of 800/5 A, C.L 1.0 CTs for input to APFC relay.

One set (3 Nos) phase indication lamp with backup SP MCB.

Protection Relays & Interlocking for transformer breaker:

Transformer breaker to be provided with :

One(1) set of multifunctional protection relay suitable for 50, 50N, 51, 51N, 27, 59 and 95. with one set of 1600/5 A, 5 P10 CTs .

Metering & Indication For DG supply breakers:

Each Breaker shall be provided with:-

One(1) No. multifuction meter (MFM-1) with Rs- 485 port suitable for measurement of voltage, current, power factor, frequency, hour run, Power (kW,kVA, kVAR), Energy (kWH, KVAH, KVARH) and Harmonics (EM-6400 of Conzerv or equivalent).

One (1) set 3 Nos. CTs of ratio 1250/5A,15VA, Class 1.0 as required.

Volt & Ammeter of battery/Battery charger system as per specification.

Three (3) nos. phase indicating lamps with backup SP MCB.

Load on DG Set indication.

Battery charger and its indication as per specifications.

One no. 12 window Audio/visual annunciator system complete with hooter, Ack, test & Reset PBs for annunciation of low lube oil pressure, high water temperature, Engine over speed, Electrical prot trip, Engine fail to start, low fuel level complete with power supply arrangements.

Micro PLC for load management/automation for 2Nos.750KVA DG Sets, 2 Nos. 1000KVA Transformer & 1 No. Bus coupler.

Protection Relays & Interlocking for DG Supply Breaker

Each DG breaker shall be provided with

One(1) set of multifunctional protection relay suitable for 50V, 50N, 51V, 51N, 32, 27, 59 and 95. with one set of 1250/5 A, 5 P10 CTs .

Notes :

Above BOQ is for the purpose of scope indentification. However, all items required for sucessful operation, protection inter locks as per operation shceme thru potential free contacts shall be provided in sufficient Nos. as required.

Sufficient No. of contacts terminals shall be provided in the panel as required for necessary remote operation and indications etc.

Operation interlocks as per specification & drawings indicating sufficient nos. of potential free contacts for interlocking/indication annunciation/ control etc shall be provided by the bidder as required.

MANUAL / AUTO SYNCHRONIZING AND LOAD SHARING + AUTO LOAD MANAGEMENT PLC CONTROL PANEL.

PLC microprocessor Based DG Control :

Design, manufacture, assembly & supply of PLC microprocessor based control logic having following features :

AMF operation through PLC with all necessary features for manual operation. (to be done when PLC is not available or out of circuit).

Auto Synchronisation System.

Auto load sharing among D.G. Sets.

Auto load shading and Load management.

Above system components shall be housed in the DG AMF Cum Synchronisation Panel complete with all accessories as per requirement I/O racks, relay modules, synchronizing module (Deif/Woodward or equivalent) with all DG protection, operation interface with Pentium IV Computer with 40GB HDD, 14" SVGA Color monitor, 80 column printer, 101 keys keyboard mouse etc, communicable cable, graphic station software, atleast 1 KVA UPS 45 minutes backup by Ni-cd maintenance free batteries, PLC to PC Communication card. The system should be suitable for controlling Two (2) Nos. DG breakers and One (1) No. bus coupler breakers . The system shall have total manual override so that it is possible to operate the DG Sets in the manual mode in the event of non-availability of PLC Control. The offer shall be inclusive of all power and control interface cabling for required I/O signals.

The software should have provision to start the DGs independetly and feed respective loads as first choice. However, it should be possible to Synchronise DGs on NO load as well as ON load.

Notes :

For metering requirement of input to PLC from various relays, CB positions etc, suitable CTs/PTs/TBs and interface for analog & digital input/output shall be provided to achieve successful operation of the DG Set & system as a whole.

BOQ given above is for a composite panel identifying the scope of supplies. However, bidder shall include all such components as are necessary for a successful and safe AMF scheme in both manual as well as on auto & PLC mode. PLC based DG control panel shall be integrated in the DG AMF Cum Synchronisation Panel.

Above BOQ is only for the purpose of scope identification. However all item required for protection interlocks as per operation scheme through potential free contacts for operation & control shall be provided in sufficient number as required.

Necessary Co-ordination with the DG Vendor for successful operation shall be done by Panel Vendor without any extra cost.

Required interlock should be provided so that transformer and DG supply are not paralleled.

Controller based synchronisation is also acceptable.The Bidder quoting with controller based synchronisation, should not quote for the LSM based PLC system.

Manual Synchronization Panel:

Design, manufacture, assembly & supply of Manual Synchronising Panel shall consist of :

One (1) No. double voltmeter.

One (1) No. double frequency meter.

One (1) No. synchros cope with PT & glow lamps.

QDCTs for parallel operation of DGs.

One (1) No. Syn. Switch.

One (1) No. check syn. Relay.

Bus Bar :

2 Nos. 2000A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 35kA. Neutral busbar shall be of 100% capacity.

Aluminium Bus bar with colour coded, heat shrinkable sleeves. (with 100% neutral). Separate earth Bus of 50 x 6 mm Aluminium shall be provided.

Bus Coupler :

One (1) no. 2000 Amps, 415 V, 35kA four pole EDO Bus coupler breaker complete with under voltage and shunt trip release, anti pumping protection, ON/OFF/ indication etc. to be interlocked with the incommers to allow closing of breakers in such a way that either transformer or DG Sets supply can be fed to the buses in all operating condition and necessary interlocking can be achieved as per approved SLD

Outgoings

Each outgoing feeder shall consist of following:

3 Nos. phase indication lamps and 3 Nos. status indication lamps for ON/OFF/ Trip with control SP MCB.

6 Nso. 315 Amps TPN Moulded Case Circuit Breaker (Icu = Ics) with built in Microprocessor based release unit for short circuit and over current

2 No. 800 Amps TPN Moulded Case Circuit Breaker (Icu = Ics) with built in Thermal Magnetic based release unit for short circuit and over current without multifunctional meter for capacitor panel.

24 Nos. 250 Amps TPN Moulded Case Circuit Breaker (Icu = Ics) with built in Thermal Magnetic based release unit for short circuit and over current

Main LT Panel as described above complete with specifications and enclosed SLD

CAPACITOR PANEL 350 kVAR ( 50 kA) Integrated with LT Panel

Incoming

Incoming breaker already taken in LT Panel hence not required here.

3 Set of 800 /5A for , CL-1.0, 15VA measuring CTs for Metering

1 Set of phase indicating lamps with MCB.

Terminals to receive XLPE insulated cable

8 step APFCR relay microprocessor based to sense and monitor the system power factor and provide impulses for operation of 6 sequential capacitors circuits

Power factor meter ( digital )

Bus bars

1000A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 50 kA. Neutral busbar shall be of 100% capacity.

Outgoings

350 kVAR Capacitor Panel as described above complete with specifications and enclosed SLD

SUB-HEAD IV: 415V MAIN DISTRIBUTION BOARDS

Design, fabrication, assembling, wiring & supply, installation, testing & commissioning of MV Panels fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA painted sheet steel in cubicle formation with reinforcement of suitable size angle iron, channels, T irons, flats wherever necessary for large meter boards. Cable gland plates shall be provided at top and bottom both and windows for meter reading, locking arrangement (pad-lock & seal) with wiring upto KWH meter & meter to MCB shall be done by using adequately rated flexible single core copper wire. The boards shall be treated with all anticorrosive process before painting as per standards with final approved shade of powder coated as approved, 2 nos. earthing terminals shall be provided for all panels. The boards shall be suitable for 415 V, 3 phase, 4 wire, 50 Hz supply system. Boards shall be fabricated in length, height, depth etc to match with site conditions.

An approval shall be taken for each panel before manufacturing. Galvanised hardwares with zinc passivation shall be used in fabrication of boards.

Note: The following provisions shall be required to be made in the switchboard detailed below

The Switchboard shall have provision for entry of all PVCA cables/bus duct from the top/bottom as required.

All live accessible parts shall be shrouded and all equipment shall be finger touch proof. The busbar insulation shall be with heat shrinkable sleeves. SMC/DMC shrouds and busbar supports shall be used.

Suitable tinned copper extension links for incoming/outgoing cables shall be provided wherever required

Positive isolation of all breakers.

All fault level breaking capacity indicates shall be IC.S value at 415 volts (ICS = ICU = ICW = 100%).

Space Heater/ light/air filter shall be provided for each vertical compartment

Padlocking facility shall be provided on all outgoing feeders.

All ACB’s shall have all standard accessories such as CT’s, Arc Chute, Safety Shutters etc.

All inter Panel wiring from PLC to DG / Transformer / Bus Couplers as required.

Link and drops from ACB/MCCB shall be designed for full rated current of ACB/MCCB ratings at same current density as of Main Bus Bar

2 nos. GI earth strip throughout the panel.

PANEL MP-3 & MP-4 (35 Ka)

Incoming #1

2 Nos. 315A, FP MCCB with Micro processor based O/L , S/C and E/F Releases (Ics=100% Icu) and consisting of following

Metering, Indication & Protection:

1 Nos. Voltmeter with VSS

1 Nos. Ammeter

1 Sets supply available indicating lamps with control MCBs.

R-Y-B and ON/OFF indication lamps for incomer

6 Parameter Energy Analyser with Required CTs

Bus Coupler:

315A, FP MCCB with Micro processor based O/L , S/C (Ics=100% Icu) Bus coupler interlocked with both incomers.

Bus Bar:

500A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 35 kA. Neutral busbar shall be of 100% capacity.

Outgoings

4 Nos. 100A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu) with 0-24 Hour Timer with contector.

4 Nos. 100A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

4 Nos. 160A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

6 Nos. 63A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

PANEL MP-3 & MP-4 as described above as per SLD

WTP PANEL

Incomer:

1 Nos.100 A TPN MCCB (25 kA)

Metering, Indication & Protection:

1 Nos. 6 Parameter Energy Analyser with 3 Nos. Cast Resin CTs and MCBs

Breaker ON OFF indication Lamps

R-Y-B indication lamps with MCBs

Busbar :

150A TPN Aluminium bus bars of short circuit with stand capacity 25kA & insulated with heat shrinkable,colour coded sleeves.

Outgoing :

3 Nos. DOL Starters (2W+1S), suitable for 2.0 Kw motor, complete with 25A TP MPCB with thermal range as per Type-II co-ordination chart. (Raw water Feed Pump for Domestic wate)

2 Nos. DOL Starters (1W+1S), suitable for 3.0 Kw motor, complete with 25A TP MPCB with thermal range as per Type-II co-ordination chart. (Hydropneumatic pumps for Dom. Water transfer to OHT(Raw) of Individual Villas.)

2 Nos. DOL Starters (1W+1S), suitable for 5.0 Kw motor, complete with 25A TP MPCB with thermal range as per Type-II co-ordination chart. (Booster pumps for Irr. Water Supply)

2 Nos. DOL Starters (1W+1S), suitable for 1.0 Kw motor, complete with 25A TP MPCB with thermal range as per Type-II co-ordination chart. (Pump Rm. Sump Pumps)

2 No. 25A DP MCB for Dosing Pump

2 No. 25A TPN MCCB Spare

WTP PANEL: described as above and as per SLD

EXTERNAL FEEDER PILLARs (External Lighting)

Design, fabrication, supply , Installation , testing and commisioning of Feeder Pillar fabricated out of 2mm thick for structural members (Load bearing members) and 1.6mm thick for door and covers (Non load bearing members) CRCA sheet in cubicle compartmentalize free standing floor mounted, dust and vermin proof outdoor type double door with reinforcement of suitable size angle iron, channel 'T' irons and / or flats wherever necessary. Cable gland plates shall be provided at the bottom of the panels. Panels shall be treated with all anticorrosive process before powder coating as per specifications with 2 coats of PU paint primer and final approved shade of PU paint coating. 2 Nos. earthing terminals shall be provided for all distribution panels. Panels shall be suitable for 415V, 3-phase, 4-wire, 50Hz supply system and with 15% spare space, lifting hooks shall also be provided in case of large panels.

Approval shall be taken for each panel before fabrication. Galvanized hardwares with zinc passivation shall be used in fabrication of panels.

INCOMING

2 Nos. 100 Amp TPN MCCB with Micro processor based O/L , S/C (Ics=100% Icu)

1 set of phase indicating lamps with MCB.

Digital Amps &Volt meter

BUS COUPLER

100A, FP MCCB with Micro processor based O/L , S/C (Ics=100% Icu) Bus coupler interlocked with both incomers.

BUSBAR

150 Amp FP aluminium busbars (Current Density 1A/Sq.mm) with 100% neutral.

OUTGOING

2 Nos. 40A TPN MCB

3 Nos. 20A DP MCB

1 No. 63A FP MCCB Complete with 1 no 24 hrs programmable timer & contactor for automatic operation of external lighting and with 12 nos. 10A/20A/25A amp DP MCB, 10 KA with thermal magnetic protective releases as outgoings for external lighting

Feeder Pillar as Described Above as describe above as per SLD

SUB-HEAD VIII : EXTERNAL LIGHTING

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 90x90x100 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for sluice valve, with C.I. surface box 100 mm top diameter, 160 mm bottom diameter and 180 mm deep (inside) with chained lid and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size ), i/c necessary excavation, foundation concrete 1:5:10 (1 cement : 5 fine sand : 10 graded stone aggregate 40 mm nominal size ) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design :

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

Constructing masonry Chamber 60x45x50 cm inside, in brick work in cement mortar 1:4 (1 cement : 4 coarse sand) for water meter complete with C.I. double flap surface box 400x200x200 mm (inside) with locking arrangement and RCC top slab 1:2:4 mix (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) , i/c necessary excavation, foundation concrete 1:5:10 ( 1 cement : 5 fine sand:10 graded stone aggregate 40 mm nominal size) and inside plastering with cement mortar 1:3 (1 cement : 3 coarse sand) 12 mm thick, finished with a floating coat of neat cement complete as per standard design

With common burnt clay F.P.S.(non modular) bricks of class designation 7.5

ERRACTION OF EXTERNAL LIGHTING:

Erraction testing & commissiong Of KP-8328 Pelican Orna Florian Lighting Pole, Ht.9000, Customized to 9 meter height pole. Height to accomodate the looping type cable end box, Single pole MCB with mounting channel Integral in - built flush door consisting of 4 Way connector for incoming and outdoing cable including excabation and refilling etc complete as required (Make: K-Lite or equivalent.)

Erraction testing & commissiong of KP-9206 Foundation Bolt, 4 Nos of M20 x 500 mm bolt with 2 Nuts & 2 Washer complete as required.

Erraction testing & commissiong of KL-6791 Pelican Fort, Dimension : A9 : Ø634 x 618, A11 : Ø634 x 412, A12 : Ø634 x 610, Wattage : 1 x 60W LED complete with all accesries as required. (Make: K-Lite/Pacer-5637 or equivalent.)

Erraction testing & commissioning of KP-4340 Causeway Lighting Pole, Ht.4.5Mtr. Customized to 4.5 meter height poleHeight to accomodate the looping type cable end box, Single pole MCB with mounting channel Integral in - built flush door consisting of 4 Way connector for incoming and outdoing cable including excabation and refilling etc complete as required (Make: K-Lite or equivalent.)

Erraction testing & commissioning of KP-9204 Foundation Bolt, 4 Nos of M16 x 300 mm bolt with 2 Nuts & 2 Washer complete as required.

Erraction testing & commissioning of KL-4932 Magudam Midi, Dimension : Ø350 x 680, Wattage : 20W LED complete with all accesries as required(Make: (K-Lite/Umbrella or equivalent.).

Erraction testing & commissioning of Wall mounted street light 40W LED complete with all accesries as required(Make: (K-Lite/Pacer-5637 or equivalent.).

Erraction testing & commissioning of Up Lighter 7W LED complete with all accesries as required(Make: (K-Lite/Trioscate-7052 or equivalent.).

SITC of Ceiling hung Light 12W LED complete with all accesries as required(Make: (K-Lite/Jado Mini-2735 or equivalent.).

Erraction testing & commissioning of submerged up Lighter 30W LED complete with all accesries as required(Make: (K-Lite/Palican-3014 or equivalent.).

Erraction testing & commissioning of Bollard Lightr 6x2W LED complete with all accesries as required(Make: (K-Lite/Under Water-6700 or equivalent.).

Erraction testing & commissioning of Wall mounted up down Light 12W LED complete with all accesries as required(Make: (K-Lite/Sleek Bolard Flat Top or equivalent.).

LT cables

Supply of following Cables:-

3 core, 6.0 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3 core, 10 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

3 core, 16 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade size not exceeding 35Sqmm direct in ground including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number additional PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade size not exceeding 35 Sqmm direct in ground horizontal formation in the same trench including excavation, sand cushioning, protective covering and refilling the trench etc as required.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade size not exceeding 35Sqmm in the existing RCC/ HUME/ METAL pipe as required.

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

2C x 6 sq mm

2C x 10 sq mm

2C x 16 sq mm

Earthing with G.I. earth pipe 4.5 metre long, 40 mm dia including accessories, and providing masonry enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal/coke and salt as required.

Supplying and fixing 50mm dia GI pipe on the pole for cable entry to junction box as required.

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

Wiring with 2 x 4.0 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC conduit alongwith 1 No. 4.0 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required

Providing, laying and fixing following dia RCC pipe NP2 class (light duty) in ground complete with RCC collars, jointing with cement mortar 1:2 (1 cement : 2 fine sand) including trenching (75 cm deep) and refilling etc as required.

100 mm dia

150 mm dia

SUB-HEAD V: EARTHING

Earthing with copper . Earth plate 600 mm x 600 mm x 3 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc.( with charcoal or coke and salt).as required.

Earthing with G.I. Earth plate 600 mm x 600 mm x 6 mm thick including accessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc. with charcoal or coke and salt complete as required.

Supply and laying 50mmX6 MM GI strip at 5.0 meter below ground as strip earth electride including soldering etc as required

Supply and laying 50mmX6 MM CU. strip at 5.0 meter below ground as strip earth electride including soldering etc as required

Supply and laying 32mmX5 MM CU strip at 0.50 meter below ground as strip earth electride including soldering etc as required

Supply and laying 32mmX6 MM GI strip at 0.50 meter below ground as strip earth electride including soldering etc as required

Providing and fixing 25 mm X 5 mm G.I. strip on surface or in recess for connections etc. as required.

Providing and fixing 25 mm X 5 mm G.I. strip in 40 mm dia G.I. pipe from earth electrode including connection with G.I. nut, bolt, spring, washer excavation and re-filling etc. as required.

Providing and fixing 6 SWG dia G.I. wire on surface or in recess for loop earthing as required.

Automatic Fire Suppression LPCB approved complete system for Electrical Panels (Natural Vents and Forced Airflow) type construction. Clean Agent having (Zero ODP, GWP less than or equal to 1, 20 years of warantee against regulatory bans, non chinease) 2.5 Kg capacity Novec 1230 Direct Discharge complete system consisting of DLP Assembly with automatic valve, push in connector for tube, integrated pressure switch, reed valve for on off monitoring of isolation valve, mounting bracket, End of Line adopter etc to make comlete system functional as a system.. Make;- Firetrex/Safefire/Tracefire

Fire Detection Tube: Linear pneumatic heat Detection Tube with all necessary fittings & supports. Make;- Firetrex/Tracefire/Safefire

Master Control Unit with Audio Visual Alarm with wiring to make complete system operational. The control panel should have provision of integration with fire Alarm / SCAD/ BMS system. Make;- Firetrex/Tracefire/Safefire

WIRING IN PVC CONDUITS

Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

a) Group - C

Wiring for twin controlled light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with 2 way modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ceiling fan/exhaust fan/call bell point with 2x1.5 sq.mm PVC insulated stranded copper conductor cable alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing in PVC Medium conduit as required. (Point shall be controlled / looped From existing point).

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 5A primary Socket and 16A Secondary Socket)

Same as above but in existing conduits / Raceways

Wiring with 2 x 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 1.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 5A Secondary Points)

Same as above but in existing conduits / Raceways

Wiring for light / power plug point with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC Medium Class conduit alongwith 1 No. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 16A Socket)

Same as above but in existing conduits / Raceways

DB SUBMAIN WIRING IN PVC CONDUITS

Wiring for DB submain with 4 x 10 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 4 x 6 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 2 x 6 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 2 x 10 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

POWER SOCKETS

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection,painting etc.as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required.

Supplying and fixing modular type 25 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 amps, 415 volts, 4 Pole MCB Isolator in sheet steel enclosure, on surface or in recess, complete with connections, testing and commissioning etc. as required.

Supplying and fixing 100 amps, 415 volts, 4 Pole MCB Isolator in sheet steel enclosure, on surface or in recess, complete with connections, testing and commissioning etc. as required.

FINAL DISTIRIBUTION BOARD

Supplying installation, testing and commissioning of surface-recess mounting horizental type three pole and neutral,prewired, sheet steel, MCB distribution board 415 volt, dust protected and powder painted ,inclusive of 200 amps tinned copper busbar, common netrul link, earth bar, din bar for mounting MCB detachable gland /knock out plate, and with built in loose wire box, and superior make terminal connectiors for all adequate size of FR PVC insulated copper conductor upto the terminal of following way with double door as required

B. TP&N D.B ( VERTICAL TYPE)

iv) 24 Nos. 6-32 Amps SP MCBs as outgoing =Rs. 24x160=3840

Supplying and fixing following way prewired SP&N MCB distribution board of steel sheet for 240 volts on surface/ recess complete with loose wire box, terminal connectors for all incoming and outgoing circuits, duly prewired with suitable size FR PVC insulated copper conductor up to terminal blocks, tinned copper bus bar, neutral link, earth bar, din bar, detachable gland plate, interconnections, powder painted including earthing etc. as required.

E. SPN D.B (SINGLE DOOR)

iii) 12 Nos. 6-32 Amps SP MCBs as outgoing =Rs. 12x160=1920

10KVA online UPS 3phase input & 3phase output power systemof input voltage 360/380/400/485V AC frequency range 40HZ/60HZ +-10% output voltage range 415V +-1% frquency range 50HZ +-1% power facor 0.8/3.1, harmonics distirtion <2% THD (linear load) 5% THD (Non linar load).

Batteries:

12 volt 65Ah sealed maintence free(SMF) battery with 24 month replacement guarinty

Battery Rack :

MS battery rack suitable for 15-20 Ups battery installation.

Exhaust Fans:

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply of LT Cables

3.5 core, 35 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4 core, 16 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4 core, 10 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4C-4.0Sq. mm Copper Armoured cable

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ STONE WARE / METAL pipe/ Cable Trays as required.

Upto 35 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 35 sq. mm.

4core 16sq. mm.

4core 10sq. mm.

4C-4.0Sq. mm

Cable Trays

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.( Powder coated shall be of Siemens Grey Colour- RAL 7032)

450 mm width X 50 mm depth X 2.0 mm thickness

300mm width X 50mm depth X 1.6 mm thickness

150mm width X 50mm depth X 1.6 mm thickness

SUB-HEAD II: INTERNAL LIGHTING FIXTURE & FANS

Supplying and fixing reccessed mounted 36 W 2'x2' LED complete with all accesories and replacable electronic driver and directly on false ceiling including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing reccessed mounted 20 W LED vertical down lighter complete with all accesories and replacable electronic driver and directly on false ceiling including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing 18W LED ceiling recessed light complete with electronic driver including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing Surface mounted 10/12 watt LED type Bulk-head fitting comprising of pressure die cast housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc directly on wall/ceiling including connection with 1.5 sq.mm FR PVC insulatedcopper conductor cable and earthing the body etc. as required..

Supplying and fixing Surface mounted 15 watt LED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing Wall mounted bracket 18 watt LED complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing Cove Light 5 watt LED per meter complete with integrated electronic driver & including connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing of 11 watt LED mirror light complete with integrated electronic driver & ncluding connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing of 1X28W Watt Dustlight Proof LED light complete with integrated electronic driver & ncluding connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing of CHANDELIER LIGH complete with integrated electronic driver & ncluding connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required

Supply of 1200mm Dia ceiling sweep Fan with all accesries.

Supplying and fixing two module stepped type electronic fan regulator on the existing modular plate switch box including connections but excluding modular plate etc. as required

WIRING IN PVC CONDUITS

Wiring for Light point / Fan point / Exhaust Fan point / Call Bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

a) Group - C

Wiring for twin controlled light point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit , with 2 way modular switch ,modular plate ,suitable GI box and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required.

Wiring for light/ceiling fan/exhaust fan/call bell point with 2x1.5 sq.mm PVC insulated stranded copper conductor cable alongwith 1 No. 1.5 sq.mm PVC insulated copper conductor cable for earthing in PVC Medium conduit as required. (Point shall be controlled / looped From existing point).

Wiring with 2 x 2.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 2.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 5A primary Socket and 16A Secondary Socket)

Same as above but in existing conduits / Raceways

Wiring with 2 x 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 1.5 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 5A Secondary Points)

Same as above but in existing conduits / Raceways

Wiring for light / power plug point with 2 x 4 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed PVC Medium Class conduit alongwith 1 No. 4 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.( For 16A Socket)

Same as above but in existing conduits / Raceways

DB SUBMAIN WIRING IN PVC CONDUITS

Wiring for DB submain with 4 x 10 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 4 x 6 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 2 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 2 x 6 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Wiring for DB submain with 2 x 10 sq.mm FR PVC insulated copper conductor single core cable in surface / recessed Medium Class PVC conduit alongwith 1 No. 6 sq.mm FR PVC insulated copper conductor single core cable for loop earthing as required.

POWER SOCKETS

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 3 pin 5 / 6 amps modular socket outlet and 5 / 6 amps modular switch,connection,painting etc.as required.

Supplying and fixing suitable size GI box with modular plate and cover in Front on surface or in recess ,including providing and fixing 6 pin 15 / 16 modular socket outlet and 15 / 16 amps modular switch,connection,painting etc.as required.

Supplying and fixing modular type 25 amps A.C. unit box with ON/OFF MCB on surface or in recess complete with connections, testing and commissioning etc as required

Geyser/ Toilet Inline Fan point consisting of following :- - 1 No. 6 pin No 6/16A Modular Socket in 2 Module Box with modular Plate near Geyser - 1 No 6/16A Modular Switch in 2 Module Box with Modular plate near entry at switch board level - Wiring between Socket and Switch board with 3 Nos. 4.0 Sq. mm Cu Wire in conduit including connections at both ends

Supplying and fixing 20 amps, 240 volts, SPN industrial type, socket outlet, with 2 pole and earth, metal enclosed plug top alongwith 20amps "C" curve, SP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 20 amps, 415 volts, TPN industrial type, socket outlet, with 4 pole and earth, metal enclosed plug top alongwith 30 amps "C" curve, TP MCB, in sheet steel enclosure, on surface or in recess, with chained metal cover for the socket outlet and complete with connections, testing and commissioning etc. as required.

Supplying and fixing 63 amps, 415 volts, 4 Pole MCB Isolator in sheet steel enclosure, on surface or in recess, complete with connections, testing and commissioning etc. as required.

FINAL DISTIRIBUTION BOARD

Supplying installation, testing and commissioning of surface-recess mounting horizental type three pole and neutral,prewired, sheet steel, MCB distribution board 415 volt, dust protected and powder painted ,inclusive of 200 amps tinned copper busbar, common netrul link, earth bar, din bar for mounting MCB detachable gland /knock out plate, and with built in loose wire box, and superior make terminal connectiors for all adequate size of FR PVC insulated copper conductor upto the terminal of following way with double door as required

B. TP&N D.B ( VERTICAL TYPE)

iv) 24 Nos. 6-32 Amps SP MCBs as outgoing =Rs. 24x160=3840

E. SPN D.B (SINGLE DOOR)

iii) 12 Nos. 6-32 Amps SP MCBs as outgoing =Rs. 12x160=1920

5KVA online UPS 3phase input & 3phase output power systemof input voltage 360/380/400/485V AC frequency range 40HZ/60HZ +-10% output voltage range 415V +-1% frquency range 50HZ +-1% power facor 0.8/3.1, harmonics distirtion <2% THD (linear load) 5% THD (Non linar load).

Batteries:

12 volt 65Ah sealed maintence free(SMF) battery with 24 month replacement guarinty

Battery Rack :

MS battery rack suitable for Ups battery installation.

Exhaust Fan:

Supply and installation of 300 mm, 230 v A.C. exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.

Extra for fixing the louvers/ shutters complete with Frame for a exhaust fan of all sizes

Providing and fixing M.V. danger notice plate of 200 mm X 150 mm, made of mild steel at least 2 mm thick, vitreous enameled white on both sides, and with inscription in single red colour on front side as required.

Supply of LT Cables

3.5 core, 35 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4 core, 16 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

4 core, 10 sq. mm XLPE/PVC insulated sheathed (Heavy duty) armoured electrical cable with aluminium conductor.

Laying of one number PVC insulated and PVC sheathed / XLPE power cable of 1.1 KV grade of following size in the existing RCC/ HUME/ STONE WARE / METAL pipe/ Cable Trays as required.

Upto 35 sq. mm

Supplying and making end termination of following sizes with brass compression gland including providing and crimping solderless plugs/ferrules of sizes PVC insulated PVC sheathed aluminum conductor armoured cable 1.1 KV grade.

3.1/2 core 35 sq. mm.

4core 16sq. mm.

4core 10sq. mm.

Cable Trays

Supplying and installing following size of perforated painted with powder coating M.S. cable trays with perforation not more than 17.5%, in convenient sections, joined with connectors, suspended from the ceiling with M.S. suspenders including bolts & nuts, painting suspenders etc. as required.( Powder coated shall be of Siemens Grey Colour- RAL 7032)

300mm width X 50mm depth X 1.6 mm thickness

150mm width X 50mm depth X 1.6 mm thickness

SDB-12.1 UPS PANEL (CLUB)

Incoming

1 Nos. 63A, TPN MCCB with thermal magnetic release having overload and short circuit protection. (Ics=100% Icu)

Metering, Indication & Protection:

Combind digital Ammeter & volt meter , CL-1 CT ratio.

1 Sets supply available indicating lamps with control MCBs.

ON/OFF indication lamps for incomer

Bus Bar:

100A, Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 10 kA. Neutral busbar shall be of 100% capacity.

Outgoings

10 Nos. 40 Amps 4 Pole MCB

SDB-1.1 UPS PANEL as describe above as per SLD.

MDB - 12 CLUB (35 Ka)

Incoming #1

2 Nos. 250A, FP MCCB with Micro processor based O/L , S/C and E/F Releases (Ics=100% Icu) and consisting of following

Metering, Indication & Protection:

1 Nos. Voltmeter with VSS

1 Nos. Ammeter

1 Sets supply available indicating lamps with control MCBs.

R-Y-B and ON/OFF indication lamps for incomer

6 Parameter Energy Analyser with Required CTs

Bus Coupler:

250A, FP MCCB with O/L , S/C (Ics=100% Icu) Bus coupler interlocked with both incomers.

Bus Bar:

300A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 35 kA. Neutral busbar shall be of 100% capacity.

Outgoings

10 Nos. 63A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

1 Nos. 100A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

2 Nos. Star Delta Starters , suitable for 18 Kw motor, complete with 63A TP MPCB with thermal range as per Type-II co-ordination chart. (VRV Units at Terrace )

MDB-12 Club as described above as per SLD

MDB - 14 DORMITRIES(Light & Power)

Incoming #1

2 Nos. 125A, FP MCCB with Micro processor based O/L , S/C and E/F Releases (Ics=100% Icu) and consisting of following

Metering, Indication & Protection:

1 Nos. Voltmeter with VSS

1 Nos. Ammeter

1 Sets supply available indicating lamps with control MCBs.

R-Y-B and ON/OFF indication lamps for incomer

6 Parameter Energy Analyser with Required CTs

Bus Coupler:

125A, FP MCCB with O/L , S/C (Ics=100% Icu) Bus coupler interlocked with both incomers.

Bus Bar:

200A, TPN Al. Bus Bar of suitable length having Current density 1Amp/sq.mm & having high conductivity electrical grade suitable to withstand symmetrical fault level of 35 kA. Neutral busbar shall be of 100% capacity.

Outgoings

10 Nos. 63A, TPN MCCB with thermal magnetic release having overload and short circuit protection and with ON indication lamp . (Ics=100% Icu)

MDB-14 Dormitries as described above as per SLD

INTERNAL LIGHTING FIXTURE & FANS

Supplying and fixing reccessed mounted 36 W 2'x2' LED complete with all accesories and replacable electronic driver and directly on false ceiling including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing reccessed mounted 20 W LED vertical down lighter complete with all accesories and replacable electronic driver and directly on false ceiling including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing 18W LED ceiling recessed light complete with electronic driver including connection with 1.5 sq . Mm FR PVC insulated copper conductor and earthing the body as reqd.

Supplying and fixing Surface mounted 10/12 watt LED type Bulk-head fitting comprising of pressure die cast housing with acrylic diffuser (IP65) and complete with integrated electronic driver etc directly on wall/ceiling including connection with 1.5 sq.mm FR PVC insulatedcopper conductor cable and earthing the body etc. as required..

Supplying and fixing Surface mounted 15 watt LED downlighter complete with integrated electronic driver & LED directly on ceiling including connection with 1.5 sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing Cove Light 5 watt LED per meter complete with integrated electronic driver & including connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

Supplying and fixing of 1X80 Watt High bay LED light complete with integrated electronic driver & ncluding connection with 1.5sq.mm FR PVC insulated copper conductor cable and earthing the body etc. as required.

FIRE ALARM AND DETECTION SYSTEM

Supplying and fixing of following sizes of steel conduit alongwith the accessories in surface / recess including painting in case of surface conduit or cutting and making good the same in case of recessed conduit as required as per specification.

25mm dia M.S. conduit.16 SWG M.S. conduit

32mm dia M.S. conduit.16 SWG M.S. conduit

Supplying and laying of following sizes FRLSLS PVC insulated single core copper wire in existing conduit complete as required.

2x1.5 sq mm

2x2.5 sq mm

Supplying, installing, testing and commissioning of the following as per specification complete with junction box, as and where required.

Analogue addressable Photo Electric type Smoke Detector with mounting base, address switch complete as required.

Analogue addressable rate of rise cum fixed temperature thermistor type heat detector with mounting base, address switch complete as required.

Addressable type Manual Call Point complete as required.

Addressable Hooter cum strobe complete as required.

Analogue addressable Fault Isolators for isolating shorted, de-wired and loose circuits between two successive Fault isolators with automatic resetting arrangement. (max. 20 devices for one fault isolators).

Addressable Input Card/monitor module for connecting to Flow Switch etc.

Panel shall have programmable switch plates for controlling horn strobe zones/AHU shut off etc. from panel itself. Panel shall have inbuilt autodialer with minimum 6 line output. Panel shall have its own master fire fighting telephone/audio control/command centre.

The Panel shall also have Logic hardware and software built into it for initiating specific AHU tripping, time delay operation of strobe, subsequent operation of electronic speakers, and finally hooters.

2 loop panel

Providing, installing, testing and commissioning of zero loop Repeater Panel for Fire Alarm System with piezo sounder, LCD alpha numeric character display with accept/reset buttons for alarm address of any sensor/field device. The Repeater Panel shall provide field device address as required. The Repeater Panel shall be active & all the setting for fire alarm system can be configured with panel.

PUBLIC ADDRESS SYSTEM :

Ceiling mounted baffle speaker with three tap changers (2W).

Fire Fighter Telephone System :

Portable UL listed fire phone handsets in a suitable enclosure.

Addressable fire phone jack plates with control/monitor module.

TOTAL ROOM FLOODING SYSTEM

34/80/120/140/180 Itr completele CCOE approved high pressure seamless BIS 7285 approved Cylinders having 34/80/120/140/180 ltr capacity, UL/FM approved based Novec 1230 clean agent stored pressurized system with PESO approved valve assembly . The system also to be fitted with digital pressure gauge having alogirthm of pressure with respect to temperature to monitor real time pressure and temperature with safety burst disc safety cap, elbow and other accessories, mounting bracket, container straps, NRV , Pressure operated control head which shall allow for pressure actuation of gas mounted, manually operated actuator to actuate the gas flooding process with the help of a lever, flexible rubber hose with wire bralded enforcment to route the gas from the storage cyinder to the discharge piping, to be connected to the discharge outlet of gas cylinder valve & to be terminated at the system piping or discharge manifold, Flexible actuation hose complete as required. Designated to provide proper flow rate & distribution Novec 1230 gas to flood the hazard area as per latest NFPA 2001.

The system shall sustain upto 65oC operating temperature. filling facility shall be in India and shall be UL approved.The complete gas suppression system shall be UL/FM approved. As system is UL/FM approved , the software for calculation used to be UL/FM approved. The documentary evidence to pe provided for all approval during the time of bidding. Make:- Janus/Tyco/Gastec/Firetrex

120/140/180 Itr complete PESO approved high pressure seamless BIS 7285 approved Cylinders with Peso approved valve, respective size mounting bracket. Each cylinder must be fitted with digital pressure gaugehaving alogirthm of pressure with respect to temperature to monitor real time pressure and temperature of cylinder at any given point to measure and view the data remotely through an online dash board or mobile application using gateways, iot (internet of things), or sim technology. The system should be capable of giving earlier warning for low pressure in a container and micro leak detection analysis and notification. Make:- Janus/Tyco/Gastec/Firetrex

34/80 Itr complete PESO approved high pressure seamless BIS 7285 approved Cylinders with Peso approved valve, respective size mounting bracket. Each cylinder must be fitted with digital pressure gaugehaving alogirthm of pressure with respect to temperature to monitor real time pressure and temperature of cylinder at any given point to measure and view the data remotely through an online dash board or mobile application using gateways, iot (internet of things), or sim technology. The system should be capable of giving earlier warning for low pressure in a container and micro leak detection analysis and notification. Make:- Janus/Tyco/Gastec/Firetrex

Novec 1230 manufactured by 3M, with Zero Ozone Depeltion Potential and Very Low Global Warming Potential of 1 with 20 Years Blue Sky Warantee against any regulatory Bans and Restrictions. UL Listed & FM approved

Master Cylinder Kit complete comprises of Electric Control Head operated electrically from the detection and control system with a manual actuator and Wire Braided Flexible Rubber Hose with Elbow and connectors complete assembly to Connect Novec 1230 Cylinder Assembly Discharge outlet with Discharge Pipe or Discharge Manifold. On any displacement of solenoid valve, master cylinder kit shall be able to notify the fault by audio/visual mean. UL Listed / FM approved Make:- Janus/Tyco/Gastec/Firetrex

Slave Cylinder Kit complete comprises of Pneumatic Control Head operated Pneumatically from master control head and Wire Braided Flexible Rubber Hose with Elbow and connectors complete assembly to Connect Novec 1230 Cylinder Assembly Discharge outlet with Discharge Pipe or Discharge Manifold. UL Listed / FM approved Make:- Janus/Tyco/Gastec/Firetrex

Supply of manifold check valve for non return arrangement of Novec 1230 gas after discharge back into cylinder. UL Listed / FM approved Make:- Janus/Tyco/Gastec/Firetrex

Warning Signs and Plates for Inside Room and Outside Room application.

Discharge Nozzles to Discharge Novec 1230 Gas in the Hazard Area as hydraulic calculation and flow rate required in 180 Deg/360 Deg Discharge Pattern. UL Listed / FM approved Make:- Janus/Tyco/Gastec/Firetrex

Discharge pressure switch with actuation hose and fittings to connect - standard (UL/FM) Make:- Janus/Tyco/Gastec/Firetrex

Discharge Pipe with Support and Fittings, CS Seamless to ASTM A-106 Schedule 40. Make:- Maharastra seamless/Tata

Fire Alarm System with respect to Room size Automatic Gas Extinguishing Panel. 2 No’s of programmable Initiating Device Circuit and 1 No’s of Releasing Agent circuit, with the independent correlation of any no of initiating devices circuit . History event log shall be atleast of 256 events. UL Listed / FM approved/IS complied Make:- Janus/Tyco/Gastec/Firetrex/Hampton

Manual Release Switch & Abort Switch . The Dual action Manual release switch to provide the signal of fire manually to Gas release panel. UL/FM/IS complied Abort Switch. The Dual action Abort switch to provide the signal of fire manually to Gas release panel for abort. UL/FM/IS complied Make:- Janus/Tyco/Gastec/Firetrex/Hampton

Audio Visual Alarm for pre alarm in case of single zone detection & discharge alarm in case of second zone detection. Make:- Janus/Tyco/Gastec/Firetrex/Hampton

Supplying and drawing of following sizes of Fire survival cable compliance to BS 7846, BS EN 60228, BS:7655, BS: 6387, BS EN 50200 & Insulation as per BS: 7655 -1.3 and armouring as per 7646 2 X 1.5 sq. mm Make:Noburn/Wrexham/Pyrotenax

Supplying, installing, testing and commissioning of the Central Control Stations consisting of the following:

Intel Core-i7 machine.

Colour Monitor 24 inch.

Laser Printer

Mouse, Keyboard etc.

Supply, installation, testing and commissioning of UL listed software for Remote programming of Fire Detection and Alarm System through central control station. The software shall be capable of the following function including licence as per specification.

Uploading and downloading of information to FACP

Graphics including autocad drawings.

Detectors information and change of detectors setting.

Software as described above.

Running meters (RM) for the cable/conduit is approximate. The contractor shall measure the running meter (RM) and procurement order shall be placed accordingly. The quantities shall be confirmed before start of work to the engineer-in charge.

EQUIPMENT - CONTOLS and CABLING

Outdoor Verifocal Camera: - Supplying, installing, testing and commissioning of Bullet camera 1/2.8" CMOS, F1.6~F3.3, Fixed Iris, 120dB, 80m IR, 0.001Lux, 2592 x1944@30fps, 2MP@60fps, 512 GB SD card slot, IP67, PoE, Built-in Mic, Audio 1/1, Alarm 2/1, Reset button, Smart VCA function, Face capture mode, Full Metal Housing. Make : Pelco/Birdeye/Axis

16 Channel NVR WITH 1 MONTH BACKUP

UTP 4 pair 23 AWG CAT 6 Cable in the existing surface/ recessed steel/ PVC conduit as required conforming to the following standards like ANSI TIA/TIA 568 C.2-1, IEC 60332-1, IEC 60754-1. Cable Dia 8.0 mm with beneding radius - 4 X Cable Diameter, pulling force is 11.5Kg. Operates at frequency of 500 Mhz

Supply, Installation, testing and commissioning of 55" Professional display with 2K resolution required as per specifications Interfaces include 2 x HDMI/DVI-D/DP, 2 x USB ports and LAN connectivity, Brightness :- 350 Nits or More, Contrast Ratio:- 1100:1, with remote control and wall mount unit etc

PVC CONDUIT - Supply, Installation, Testing & Commissioning of 25mm PVC Conduit On Surface. Along with all related laying materials

Access Control

Boom Barrier

Motorized Automatic sliding gate (9m WIDTH): Made of Stainless steel SS304 grade, as per standard design. Complete set with Sliding motor & controllers. Both automatic & manual operation. With stainless steel rails

Motorized Automatic sliding gate (6M WIDTH): Made of Stainless steel SS304 grade, as per standard design. Complete set with Sliding motor & controllers. Both automatic & manual operation. With stainless steel rails

Supports up to 6 (In/Out) via Wiegand protocol with 2 inputs and 1 output. Four additional auxiliary inputs and 2 auxiliary outputs An encrypted communication via TCP/IP. Lockable metal enclosure, includes a control board, power switcher, built-in power management board/charger, sounder.

Sliding Gate Motor Max. power 500 W Max. torque 24 Nm (*) Max. leaf width 15 m Leaf speed 12 m/min

Supply, Installation, testing and commissioning of 2-way coaxial ceiling speaker with back can, Line Transformer Tappings 15watt, Dispersion : 145° conical, Sound Pressure (Max. W/1m) : 106 dBCeramic screw terminal with link through conenctivity, Sensitivity (1W/1m) : 86dB or better etc required as per specifications. Make- Ahuja/Bosch/TOA

Supply & Fixing of Connector HDMI Cable,Audio cable Video Cable for above system OEM Approved

Video Verification & Visitor Management

IP Video Entry Station: - 7inch Touch Screen SIP Video Entry Station, SIP V.2 Compliant, Wide Angle Camera : 120 degree, Contactless Face Recognition and QR Code Access, Built in Biometric Finger Scanner and MIfare Card Reader 13.56 Mhz, RS485 and Wiegand Interface for 3rd part, Access Control Integration, Can Control up to 3 relays, 10/100 Mbps TCP/IP LAN Port, Built in Speaker and Microphone, Boom Barrier / Flap Barrier / EM Lock Integration, Unlocking using any of the above Access Control or SIP Dialing, Video Codec : H.263 / H.264, Audio Codec : G.711 , G.711μ , G.722 , G.729, Wall Mounting / Flush Mounting, IP65 Grade and Vandal Proof.

IP Video Desktop Phone 16 lines with up to 16 SIP accounts Built-in 2 megapixel camera for video calling with privacy shutter Runs on the Android 7.x operating system Built-in Bluetooth for syncing with mobile devices and connecting Bluetooth headsets Dual-switched auto-sensing 10/100/1000Mbps network ports Integrated dualband Wi-Fi (2.4GHz & 5GHz) Built-in PoE/PoE+ for power and network connections Dual-mic HD speakerphone with advanced echo cancellation & excellent double-talk performance for any scenario 64-bit quad-core processor, 2GB RAM, and 16GB Flash 8’’ (1280x800) capacitive 10-point touch screen IPS LCD Peripherals include HDMI-in/out, USB, Micro SD, headset jack, EHS (Plantronics headsets) 7-way HD audio conferencing & 3-way 1080p 30fps HD video capability

SIP Server Supports up to 3000 users and up to 450 concurrent calls Zero configuration provisioning of Grandstream SIP endpoints Built-in conferencing & meetings platform; supports desktop, Wave app, and SIP endpoints Wave for Android, iOS, Chrome and Firefox browsers allows communication with all UCM6300 users & solutions API available for third-party integrations, including CRM and PMS platforms, Advanced security protection with secure boot, unique certificate and random default password to protect calls and accounts, Three Gigabit auto-sensing RJ45 network ports with integrated PoE+ and support NAT router Automated NAT firewall traversal service facilitates secure remote connections, Supports Full-Band Opus voice codec and H.264/H.263/ H.263+/H.265/VP8 video codec, jitter resilience up to 50% packet loss, Compatible with GDMS for cloud setup, management and monitoring, Based on Asterisk* version 16 open source telephony operating system

10 inch Android SIP Based IP Based Indoor Monitor with: • Built in 1MP CMoS Camera for Video Calling • Two Way Video and Audio intercom • Built in 8 Zone Security Alarm • Alarm Records • Monitoring of Common area IP Cameras • Digital Door Lock Integration • Multimedia function : Photo Frame • Supports Call Management Center • PoE 802.af • CE and ROHS Certified • Dual Protocol , IP + SIP • IP Camera Integration

IP Camera Bell with Card Access Control • Wide Angle Camera : 110 degree • SIP V.2 Compliant • Single Key for Dialing SIP Hotline Number • Built in Mifare Card Reader 13.56 Mhz • 10/100 Mbps TCP/IP LAN Port • Built in Speaker and Microphone • EM Lock Integration • Video Codec : H.264 • Audio Codec : G.711 , G.711μ , G.722 , G.729 • PoE (IEEE802.3af, Power-over-Ethernet ) • Wall Mounting • Complies with SIPV.2 for easy Integration • High Intensity LED Light for night Vision • Built in Card Reader

Digital Door Lock Single Push Action, ONE TOUCH Biometric Scan PIN Code RFID Card, Smart Connectivity: Bluetooth, Z-Wave and Wi-Fi Mechanical Key Override, Voice Guide Feature, The voice guided operating manual for easier and more convenient use. Automatic Locking, automatically locks the door after checking it is properly closed., Alarm (Break-in / Damage) 80dB alarm goes off if anyone attempts to damage the lock or force door open. Fake PIN Code To prevent the PIN code from being exposed, It allows you to enter fake numbers before or after entering your PIN code. Low Battery and Emergency Power Low battery warning with alarm and LED. When the batteries are completely discharged, you can easily supply emergency power to the lock with the standard 9V battery

PASSIVE COMPONENT

Supplying, installing, testing and commissioning of 15U Cabinet. Size 600 X 600 mm following accessories, CRCA 'D' Grade thickness (mm) 1.2, RAL 9017(Matt Black), Glass: 4mm Toughened Tinted Glass Door, Injected one piece polyurethane gasket on frame, Accessories: Cooling Fan (230V A/C 90 CFM) - 4 Nos, Cable Manager Metal- 4 Nos, PDU 230VAC - 1 No (12 nos. 6A/16A sockets with plugs 6A/16A - 1/1pc & MCB 16A/32A - 0/1 Pc), Cable Channel 100mm wide 42U- 2 Nos, Heavy Duty Stationary Shelf 600mmW x 475mmD - 1 No., Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 3 Nos., Earthling Strips 150mm H - 1 No, Door Lock - 1 No, Front Metal Band - 1 No. Packing: 5 ply cardboard & Inside 28 ply EP foam. In the rack there must be maintained 1 U = 1.75 inches space. Make:- Brocade/Alcatel/Arista

Supply, Installation, testing and commissioning of Cat 6 Tool less Information outlet for Data & Voice. Cat6 U/UTP RJ45 socket with built in crimping mechanism with capability of retermination without refreshing the wires. Toolless RJ45 Information outlet with insertion cycle (in & out) should be 1000 times (I/O) along with front side Label holder and transparent shutter. The Information Outlet connector shall be of gold/nickel, thickness of gold > 0.8 μm. The connectors shall be compatible as per IEEE 802.3bt standard for POE++ application Make:- Brocade/Alcatel/Arista

Supply, Installation, testing and commissioning of 24 port Cat 6A 19" Modular Toolless Patch Panel (loaded) enable all possible combinations of the various types of cable (UTP, FTP, SFTP) mounted on the same panel by using various toolless connector blocks/modules. Have a metal structure enabling them to be durably fixed to the uprights of the 19” chassis and assuring automatic grounding between toolless RJ-45 connectors, the panel, and the 19” uprights of the enclosure. Include rear cable support with plastic cable guides to hold cable without need for cable ties. Include quick mounting system to mount the panel into the 19” rails without use of cage-nuts. These may be used to secure the connections of wifi access points, IP cameras, servers, or other critical devices. Front Removal IO's option for maintenance and trouble shooting with 6 Different Colours Labels for Labelling & Identification of Individual Ports. Tested and guaranteed under dual circuit IEEE PoE++ up to 90W for up to 2500 on-load connections / disconnections. Make:- Brocade/Alcatel/Arista

Supply , Installtion , Testing and comissioning of CAT6 Patch Cord - 1 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like EN 50173, ISO/IEC 60603-7 & 11801/IEC 60332-1, UL VW-1 with tensile strength >50N, number of insertion is 750 Make:- Brocade/Alcatel/Arista

Supply , Installtion , Testing and comissioning of CAT6 Patch Cord - 2 mtr with cross separator , Manufactured from stranded wires for longer flex-life , Minimum length of 1m, and maximum length of 5m Conforming to the following standards like EN 50173, ISO/IEC 60603-7 & 11801/IEC 60332-1, UL VW-1 with tensile strength >50N, number of insertion is 750 Make:- Brocade/Alcatel/Arista

Supply , Installtion , Testing and comissioning of Face Plate : Flush & surface mount. Polycarbonate Hi-Grade Plastic FR Grade with ABS underplate & CRCA metal fram & UV Resistant 850 degree C/ Glow Wire Test. The face plate should be compatible for Cat5e, Cat6 range of RJ45 and different types of AV connectors.The face plate Size should be of minimum 86x86mm Make:- Brocade/Alcatel/Arista

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed steel/ PVC conduit as required. 4 Pair CAT6 Unshielded, Twisted Pair (U/UTP) Cable 305 mtr per Box. Blue in colour conforming to the following standards like ANSI/TIA 568 C.2, EN50173, IEC 11801 2nd ED, 700Mhz etc. in Cat 6 U/UTP LCS2 cable with 23AWG. Make:- Brocade/Alcatel/Arista

Supplying, installing, testing and commissioning of 24 port Cat 6 patch panels available with block of four equipped with tool less IO, Rack Mountable. 19" Modular Patch Panel, loaded CAT6 U/UTP 24 port LCS2 rack mountable to be compatible in 4nos of 6 X RJ 45 Tool less connector U/UTP unit in a block. Make:- Brocade/Alcatel/Arista

Supplying, laying and fixing of 6 core Corrugated Steel Tape OM3 Multimode Optical Fiber of size 50/125μm LSZH. Indoor/Outdoor Universal loose tube Black Jacket through existing GI/HDPE/ Hume pipe or on cable trays inside the cable duct including all necessary fixing accessories e.g. cable ties, hardware etc. Standard & Approval : EN 50173-1 : 2002, IEC 60794-1, ISO 11801 2nd ED Make:- Brocade/Alcatel/Arista

Supplying, installing, testing and commissioning of 0/125μm OM3 LC Pigtails MM 50/125mn. Make:- Brocade/Alcatel/Arista

Supplying, installing, testing and commissioning of 6 port LCS2 Adapter plate, loaded with 3 nos. of duplex LC unit for 6 multi mode fibers of size 50/125 μm .Adapters to be compatible to fit in 19" U/UTP 24 port modular patch panel or 24 port LIU. Make:- Brocade/Alcatel/Arista

Supplying, installing, testing and commissioning of 15U Wall-mounting cabinets. size 771.35X600X500mm (HXWXD)) with all standard accessories. Width (mm) 600, Depth (mm) - 500, Approx.Net Wt (kg) - 32, CRCA 'D' Grade thickness (mm) - 1.2, RAL 9017 (Matt Black), Glass - 4mm Toughened Tinted Glass Door, Accessories:, Cooling Fan (230V A/C 90 CFM) - 2 Nos, PDU 230VAC - 1 No, Cable Manager Metal - 3 Nos, Earthling Strips 150mm H - 1 No, Mounting Hardware (20 sets of M6 screws,washer,cage nuts (nickel coated)) - 1 No, Wall Screws (4 sets of 2'' screws, washer,rubber grommet (nickel coated)) - 1 No, Door Lock - 1 No, Front Metal Band -1 No. In the rack there must be maintained1 U = 1.75 inches space. Nos. 20 Make:- Brocade/Alcatel/Arista

Supply, Installation, testing and commissioning of 1 U Horizontal Wire Manager 60mm depth (Front Side) Make:- Brocade/Alcatel/Arista

ACTIVE COMONENTS

Supplying, installing, testing and commissioning of 24-Port Giga Ethernet POE+ Smart Managed Switch with 4x1G SFP Port

Supplying, installing, testing and commissioning of 24-Port Giga Ethernet Fully Managed Switch with 4xshared SFP Port.

Supplying, installing, testing and commissioning of Tri-Band AC300 WIFI System Router with 1 Satellite Extender

Giga Duplex SC SM Media Converter

Supply, installation, testing & commissioning of Dual- band 802.11abgn/ac Wireless Access Point, 3x3:3 streams, dual ports, 802.3af PoE support. Does not include power adapter or PoE injector.should Includes Warranty and Mounting Kit complet in all respect.

Supply, installation, testing & commissioning of Wi-Fi Controller with 4 Gig Ports, with 25 APs license,Upgrage up to 50 AP Power Supply alongwith 3 year support.

HVAC WORKS

Outdoor Unit

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

20 HP (Heating +Cooling)

16 HP (Heating +Cooling)

Indoor Units

INDOOR UNIT-HIGH WALL TYPE

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

INDOOR UNIT-DUCTABLE TYPE

Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Low static ductable units (minimum 25 pascal external static pressure)

Mid Static Ductable units (minimum 45 pascal external static pressure)

Low Side Works (VRF & Ventilation System)

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

6.4 mm dia(OD)(Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

19 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

NOTE:- 1) The Copper Piping & Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.

Drain Piping

Providing and fixing of PVC drain piping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

GI volume control duct damper

I-Touch Manager (Central Remote Controller) for VRV System

Supply, Installation, Testing and Commissioning of I-Touch Manager (Central Remote Controller) suitable for indoor units, outdoor units of VRV System.

Split Type Air Conditioner-Hi Wall

1.0 TR 5 Star Split AC (Inverter Type) IS 1391 Part -1

1.5 TR 5 Star Split AC (Inverter Type) IS 1391 Part -1

2.0 TR 5 Star Split AC (Inverter Type) IS 1391 Part -1

Copper tube of size 1/4" for split AC unit 1/1.5/2/3 TR capacity including nitrile rubber insulation

Copper tube of size 1/2" for split AC unit 1/1.5/2/3 TR capacity including nitrile rubber insulation

Copper tube of size 3/8" for split AC unit 1/1.5/2/3 TR capacity including nitrile rubber insulation

Copper tube of size 5/8" for split AC unit 1/1.5/2/3 TR capacity including nitrile rubber insulation

4 kVA wall mounted automatic voltage stabilizer from ranges 140V to 280V

5 kVA wall mounted automatic voltage stabilizer from ranges 140V to 280V

Drain Pipe for AC

Outdoor stand for 1.5 TR Split AC

Outdoor stand for 2.0 TR Split AC

FR PVC insulated 3 core 4 sqmm copper wire

Ventilation Units (SITC)

Exhaust Fan for Toilets & Pantry

9"(230 mm) metal exhaust fan

Extra for fixing the louvers/ shutters complete with Frame for a exhaust fan of all sizes

Inline Fan

Supply, Loading, Unloading, Lifting, Shifting, installation, testing, commissioning of low noise acoustically lined inline fan with vibration isolators, fire rated double canvas connection & speed regulator, complete as per specification and drawing.

100 CFM @ 20 mm SP

150 CFM @ 20 mm SP

450 CFM @ 20 mm SP

600 CFM @ 20 mm SP

Electrical Works

Control & Transmission Wiring

Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper in MS conduits between indoor and out door unit and between indoor units and their remote sensor/controller.

Hi Side Works (VRF System) CLUB HOUSE

Variable Refrigerant Flow System

Outdoor Unit

Supply Installation, Testing & Commissioning of modular type Variable Refrigerant Flow/Variable Refrigerant Volume air cooled Outdoor units suitable for cooling and heating, having all hermetically sealed inverter type Scroll Compressor(s), minimum two compressors for above 14 HP modules, microprocessor based Controller, top discharge type condensing unit(s), with R 410 A Refrigerant, vibration isolators, with suitable foundation etc. complete as required. The unit shall deliver the rated capacity at AHRI Conditions and work even at 50°C ambient temperature without tripping. The unit shall be suitable to work on 400V +/- 10%, 3 Phase, 50Hz AC power supply. The unit shall be filled with first charge of the refrigerant and ready for use as required. The COP at AHRI conditions shall not be less than 3.1 and IEER not less than 6.5 .

20 HP (Heating +Cooling)

16 HP (Heating +Cooling)

Indoor Units

INDOOR UNIT-HIGH WALL TYPE

Supply, installation, testing and commissioning of following minimum capacity VRV/VRF High wall type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, outer cabinet, cord less remote control, drain pan, necessary accessories etc., suitable for operation on 230 V ± 10%, 50 Hz, single phase AC supply, complete as required. The unit shall have automatic force shut down provision in case of fire on receiving signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

INDOOR UNIT-DUCTABLE TYPE

Supply, installation, testing and commissioning of following minimum capacity and external static pressure VRF/VRV ceiling mounted ductable type Indoor unit equipped with washable synthetic media pre-filter, fan section with low noise fan/dynamically balanced blower, multispeed motor, coil section with DX copper coil, electronic expansion valve, corded remote control, outer cabinet, vibration isolators, drain pan, other necessary supports etc., suitable for operation on single phase AC supply 230 V± 10%, 50 Hz complete as required. The unit shall have automatic force shut down provision in case of fire on receiveing signal from BMS System. The cooling capacity of indoor unit will be at air inlet conditions of 27 Degree C DB and 19 Degree C WB temperature.

Mid Static Ductable units (minimum 45 pascal external static pressure)

High Static Ductable units (minimum 110 pascal external static pressure)

Low Side Works (VRF & Ventilation System)

Refrigerant Piping

Supply, Installation, testing and commissioning including vaccumiazation and Nitrogen testing of following nominal sizes of soft/hard drawn copper refrigerant piping for VRV/VRF system, complete with fittings, with suitable adjustable ring type hanger supports, jointing/brazing including accessories, insulated with XPLE Class-O tubular insulation/with Class-O closed cell elastometric nitrile rubber tubular sleeves sections of specified thickness as given below for Suction and Liquid lines, all accessories as per specifications etc. as required :

6.4 mm dia(OD)(Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

9.5 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

12.7 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

15.86 mm dia (OD) (Soft drawn) with tube thickness 1.2 mm with 19 mm thick insulation

22.2 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

28.58 mm dia (OD) (Hard drawn) with tube thickness 1.2 mm with 19 mm thick insulation

NOTE:- 1) The Copper Piping & Piping Circuit should be with Minimum Number of joints, which shall be attained by : (i) Using One End Expanded Tubes (ii) Bending the tubes instead of using elbow joints wherever 90 degree bending is required. (2) Piping should be routed at site in such a manner, that brazed joints in the refrigeration piping are kept to a minimum. (3) The makes of tube fittings shall be same as that of tubes. (4) The thickness of fittings used shall be same as that of the pipe.

Drain Piping

Providing and fixing of PVC drain piping complete with fittings, supports, 6 mm thick closed cell elastomeric insulation as per specifications and drawings.

Supply, installation, balancing and commissioning of factory fabricated GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Supply, installation, balancing and commissioning of fabricated at site GSS sheet metal rectangular/round ducting complete with neoprene rubber gaskets, elbows, splitter dampers, vanes, hangers, supports etc. as per approved drawings and specifications of following sheet thickness complete as required.

Thickness 0.63 mm sheet

Thickness 0.80 mm sheet

Supply and fixing of acoustic lining of supply air duct and plenum with 25 mm thick resin bonded glass wool having density of 32 kg/m³, with 25 mm X 25 mm GI section of 1.25 mm thick, at 600 mm centre to centre covered with Reinforced Plastic tissue paper and 0.5 mm thick perforated aluminum sheet fixed to inside surface of ducts with cadmium plated nuts, bolts, stick pins, CPRX compound etc. complete as required and as per specifications.

Supplying and fixing of following thickness duly laminated aluminum foil of mat finish closed cell Nitrile rubber (Class "O") insulation on existing duct after applying suitable adhesive for Nitrile rubber. The joints shall be sealed with 50 mm wide and 3 mm thick self adhesive nitrile rubber tape insulation complete as per specifications and as required.

Supplying & fixing of powder coated extruded aluminium Supply Air Grills with aluminium volume control dampers as per specifications.

Supplying & fixing of powder coated extruded aluminium Return Air Grills with louvers but without volume control dampers complete as required.

Supplying, fixing testing commissioning of supply air diffusers of powder coated aluminium with aluminium volume control dampers with anti smudge ring & removable core.

GI volume control duct damper

FRESH AIR/EXHAUST AIR LOUVER:

Supply, installation and testing of fresh air / louvers, bird screen in accordance with approved shop drawings and specifications.

I-Touch Manager (Central Remote Controller) for VRV System

Supply, Installation, Testing and Commissioning of I-Touch Manager (Central Remote Controller) suitable for indoor units, outdoor units of VRV System.

Ventilation Units (SITC)

Exhaust Fan for Toilets & Pantry

9"(230 mm) metal exhaust fan

12"(300 mm) metal exhaust fan

Extra for fixing the louvers/ shutters complete with Frame for a exhaust fan of all sizes

Inline Fan

Supply, Loading, Unloading, Lifting, Shifting, installation, testing, commissioning of low noise acoustically lined inline fan with vibration isolators, fire rated double canvas connection & speed regulator, complete as per specification and drawing.

100 CFM @ 20 mm SP

1000 CFM @ 25 mm SP

1350 CFM @ 25 mm SP

AHU Fan section

Supply, Loading, Unloading, Lifting, Shifting, installation, testing, commissioning of double skin AHU fan section with 25mm thick PUF insulation AHU fan section consist of Centrifugal Fan, forward curve, with radial tip double wheel, double inlet, consisting of motor, drive arrangement, aluminium common frame for fan and motor (Min IE3) , cushy foot mounting, aluminium base frame for the unit, VCD on the outlet of fan and accessories as per specification and drawing.

Badminton Court Exhaust

4000 cfm Exhaust Fan, 32 mm static pressure, 2.2 kW

Air Washer

Supply, Installation, Testing and Commissioning of Double Skin Packaged Type Air Washer with 0.63 mm preplasticized/precoated GI sheet outside and 0.63 mm plain Galvanized sheet inside with 25mm injected PUF insulation of 48KG/m3 , G.I. blower section, DIDW Blower (Backward Curved/ Plug Fans) with motors , base , drive arrangement ,Filter, cooling pad section, SS-304- Sump Tank and housing, motor drive, water circulation pump, piping, valves & fittings etc. suitable for Outdoor Application as per specifications and drawings .

Badminton Court Fresh Air

4000 CFM at 50 MM SP , Appx 3.75 KW

Electrical Works

Control & Transmission Wiring

Providing & fixing control cum transmission wiring of 2 core x 1.5 sqmm copper in MS conduits between indoor and out door unit and between indoor units and their remote sensor/controller.

M/s RVR PROJECTS PRIVATE LIMITED