Electrical Works

Amount

Renewal by Design, Engineering, Supply, Erection, Testing Commissioning and Handing over of 20 persons capacity bed cum passenger lift as per following technical specifications. Technical specifications: 1. Location: Family Planning Block A Lift IOG, Egmore Chennai- 8 2. No of lift: One Number 3. Type of lift: Bed cum passenger 4. Capacity: 20 persons (1360 kg) 5. Speed: 1.00 mtr/sec 6. Type of drive: Microprocessor based specific variable voltage variable frequency V3F drive with enhanced ride comfort and near zero leveling functions 7. No. of Floors: 6 Floors (Ground + 5 Floors) 8. Total travel: 24 mtrs. (approximate) 9. Levelling Accuracy: High Level accuracy with smooth and jerk free stopping. 10. Construction of car: special car made of stainless-steel Hair line finish car panel complete with false ceiling, flooring, lighting, fan etc., 11. Position of Machine: Directly above the lift level - Gearless 12. No. of Landing Entrance: One in front 6 Nos. 13. No. of car Entrance: One in front only 14. Landing Entrance door: (V3F) side opening power operated stainless steel No.4 hair line finish door with full height ultra slim infra-red door safety curtain. 15. Lift well: 1300mm (width) X 2400mm (depth) 16. Lift pit depth available:173m

33.Lift license: Preparation of drawing, payment of charges to CEIG and insurance policies if any and obtaining CEIG safety certificate and license as per lift act should be done by lift contractor. 34. Automatic Rescue Device: To facilitate the landing of the nearest floor at the time of power. This shall consist of suitable type battery system with charger, inverter, under voltage protection system etc., 35. Floor annunciator with music. 36. Special features: a) Infra-red door sensor b) Full height screen c) Full width half height rear panel mirror. d) Voltage stabilizer for circuit control. e) Tubular stainless steel Hand rail in car f) Signal fixtures g) Vandal proof S.S button with S.S cover h) Stain less steel door frames i) Call register signal and Vf door operator j) Braille buttons k) Stainless steel Facia for car operating panel and landing fixtures. l) ON-OFF switch for fan and light m) Over load warning indicator n) vinyl flooring

37. Over speed governor, phase failure and phase reversal relay, alarm bell, Guide brackets for car and counter weight, rubber padding under winding unit, Motor of adequate capacity, single reduction worm gear, electromagnetic brake with compression springs, car safety gears, buffer, electro mechanical door locks, emergency key, side supporting angles, motor over load protection devices, final limit switch, main suspension ropes, counter weights, lifting joint joist for mounting the machineries. 38. Guarantee: Guarantee for the Materials and workmanship of equipment complete should be offered by the Lift firm for a period of not less than one year. 39. Site testing in accordance with IS 14665 should be carried out at the time of handing over.

Renewal by supply and run of 25mm x 6mm tinned copper flat with necessary clamps / supports on wall / floor/ ground for earth connection (SD 77)

Renewal by Supply and Fixing of WT Bulk head fitting with guard suitablefor 15W LED bulb (S.D-83)

Renewal by Supply and fixing of 4 feet LED 20W fitting with LED 20W tube (Higher end) complete with TW round blocks on wall or ceiling with PVC unsheathed copper leads from terminals to the fitting. (SD-443)

Renewal by Supply and fixing of 450mm (18") sweep (light duty) AC exhaust fan complete without provision of hole in the wall. (SD 119)

Rewiring with 2 x1.5 sq.mm. (22/0.3) PVC insulated single core unsheathed FRLS copper conductor of 1100 V grade in suitable PVC rigid pipe on wall and ceiling with PVC accessories with Module Plastic surface mounting box on wall with 6A one way module switch with module front plate with painting of Suitable colour for Open PVC Light point / fan point (for electronic regulator) 5 points / coils Higher End (SD 281)

Renewal by Supply and fixing of 4-way SPMCB Distribution board with metal door with IP 42 Protection in flush with wall with 1No 32 Amps DB MCB as incoming and 2Nos 10Amps SPMCB outgoing in flush with wall and making good of the concealed portion with earth connection only. The MCB DB and MCB's should be with ISI mark (Like Hager make) (Data-1)

Renewal by Supply and fixing of 1 no.6A two module 3 pin socket , 1 no. 6A one module switch on suitable module surface mounting Box ( Plastic ) with module cover plate (plastic) on wall with connections. Higher End. (SD - 374).

Renewal by Supply and run of 2 of 1.5 Sqmm (22/0.3) PVC insulated SC unsheathed FRLS cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection 1.5 sqmm copper wire with painting suitable colour (SD 54)

Renewal by Supply and run of 2 of 4 Sqmm (56/0.3) PVC insulated SC unsheathed FRLS Cu. Conductor of 1100V grade in suitable PVC rigid pipe on wall and ceiling with continuous earth wire connection of 4 14 SWG TC wire with painting suitable colour (SD 56)

Earthing as per ISI specification with an earth electrode of 2.1 mtr class “B” GI pipe of dia not less than 40 mm with copper earth plate of size 125mm x 50mm x 6mm with necessary masonry work with 38mm RCC cover slab for brick masonry works. (SD 221)

Renewal by supply and fixing of 63 A TPNMC switch on suitable angle iron frame work with MS cable boxes with earth connection only (SD 150)

Renewal by Supply and clamping of 3 1/2 x 35 sq mm PVC LTUG armoured cable on post or on wall with MS clamps. (SD 206)

Renewal by supply and fixing of brass cable gland for 3 1/2 x 35 sqmm PVC armoured LTUG cable with earth connection(SD 165)

Renewal by Supply and providing cable end termination of 3 1/2 x 35 sq mm PVC LTUG aluminium armoured cable with necessary aluminium cable sockets by crimping etc with electrical connection complete. (SD 224))

Complete cleaning, examining and reconditioning of Lift shaft and Lift frontage with proper tools and minor civil works, plastering, water leakage treatment ,whit e washing etc.,

Pending payment for Existing lift License Fees and Liaising Charges for renewal of Existing Lift

Dismantling and clearing carefully the existing old lift complete including all the materials Such as the Lift car ,guide rails, machinery etc. as directed by the site Engineer

SREE PADMAVATHI ELECTRICALS (BID ID -1554946)