Vikramaditya Marg sthit Naya Mantri Awas No.-2 me shatigrast 04 chaukhat va 04 darwaze badalna avem samast darwazon avem khidkiyon me polish karna avem anya aavashyak vibhinn marammati karya.

Dismantling Doors, windows and clerestory window (Steel or Wood) shutter including chaukhat, architrave, holdfast etc. complete and stacking within 50 meters lead of area 3 sqm and below. DSR.No-15.12.1,

Fixing chowkhats in existing opening including embedding chowkhats in floors or walls cutting masonry for holdfasts, embedding hold fasts in cement concrete blocks of size 15 x 10 x 10 cm with cement concrete 1:3:6 (1 cement : 3 coarse sand : 6 graded stone aggregate 20 mm nominal size), painting two coats of approved wood preservative to sides of chowkhats and making good the damages to walls and floors as required complete, including disposal of rubbish to the dumping ground, all complete as per direction of Engineer-in-Charge. Door chowkhats each DSR-14.2.1

Providing wood work in frame of doors, window, clerestory window and other frames, wrought framed and fixed in posotion with hold fast lugs or with dash fasteneres of reqiured dia & lenght (hold fast lugs or dash fastener shall be paid of separately (Second class teak wood, DSR-9.1.1,

Providing and fixing ISI marked 12 mm thick Ply Fixing with Glue and Nails etc. Complete work as Per Direction of Engineer in Charge.

Providing and fixing ISI marked flush door Shutters Conforming to IS : 2202 (Part I) decorative type core of block board construction with frame lst class hard wood and well matched commercial 3 ply Veneening with vertical graints or cross brand and face veneers on both faces of shutters. 35 mm thick including ISI marked Stainless Steel butt Hinges with Necessary Screws. DSR N0-9.20.1,

Providing and fixing wire gauge shutter using galvanized M.S. wire guage of average width of aperture 1.4 mm in both directions with wire of dia 0.63, for doors, window and clerestory windows with hinges and necessary screws : 35, mm thick Shutter with ISI marked M.S. Pressed butt hinges bright finished of required Size Second class teak wood Jali Door. DSR No-9.27.1.1,

Supply and fixing of Stenless Steel Door And Window Fittings as Sliding Bolt, Tower Bolt, Handels etc. Complete as Direction of i/c.

Providing and fixing aluminium die cast body tubular type universal hydraulic door closer (having brand logo with ISI, IS : 3564, embossed on the body, door weight upto 35 kg and door widht upto 700 mm), with necessary accessories and screws etc. complete. DSR-9.83,

Polishing in high gloss/matt finish Melamine clear Polish on wood work in required colour/wooden shade texture with following process in the Sequence as detailed below.1-The surface to be polished in rubbed with sand paper 80/120 no. and then with sand paper of 160/180 nos. 2-Applying two coats of sealer with spray gun and allowing sufficient drying time for lst coat and 2nd coat is allowed to dry for 8 to 12 hrs. 3-On drying of sealer coat, wet rubbing with emery cloth of finer grading with ample water to remove excess sealer layer and make the surface futher smooth after this wet rubbing, then surface is applied with special grade melamine fillers to fill all the small and big holes/grooves etc. filler coat to be allowed to dry for 4 to 6 hrs on which again a light wet rubbing is done this surface in furface allowed to dry for 12 hrs.4- On this, lst coat of melamine polish is applied with spray gun using melamine clear polish and melamine thinner in required proportion. This 1st coat is allowed to dry for 24 hrs than this dry surface is again fine wet rubbed smooth, which is futher allowed to dry for 12 hrs. the final melamine polish ia applied with compressor pressure spray gun using melamine clear polish and melamine thinner mixed in required proportion complete as per direction of engineer - in- charge. (Final coat to be done in 1 or 2 layers without gap of time) DSR.N0-13.116),

French spirit Polishing One or more coats on old work. DSR-13.103.1,