ADDN,ALTN TO TOILETS AT BLDG NO P-01, SHIP SUPPORT COMPLEX AT NSRY, ADDN/ ALTN,SPL REP TO ROLLING SHUTTERS AT SSFC AND PUMP HOUSE AT NSRY AND PROVISION OF HARDSTAND WITH COVERED

Amount

Taking down chowkhats exc. 1.5 Sqm but not exc. 4.0 Sqm with shutter (without taking off shutters from the frames) all as specified and as directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing), removing serviceable tiles to store and removing all the rubbish as directed by Engineer-in-charge complete all as specified and directed.

Dismantling boarding, any description, fixed in any position with screws all as specified and as directed.

Dismantling wrought iron or mild steel work of any description all as specified and as directed.

S & F framed work such as grills, gratings etc with ends of bars shouldered and/or riveted or forged into spikes, framed guard bars and similar work conforming to Fe-290, Gde E-165 complete all as specified and as directed.

S & F 40 mm thick solid PVC sandwich panel with 1 mm thick plain PVC sheet on both sides suitably fixed in MS angle frame all as specified and as directed.

M & L for glazed coloured ceramic tiles 300 x 200 x 7 mm thick on vertical surfaces such as skirting, dado and risers to steps etc set and jointed in neat cement slurry and pointed in white or coloured cement to match including 10 mm thick backing coat in CM 1:4 including taking down old tiles complete all as specified and as directed.

M & L for non skid ceramic coloured joint free tiles 7 to 8 mm thick ( square/rectangular) area of each tile exc 0.06 sqm but not exc 0.11 Sqm, in floors etc. set and jointed in neat cement slurry and pointed in coloured cement to match the tiles including screed bed or bedding layer 15 mm thick in CM 1:6 for laying floor finishes and taking down old tiles complete all as specified and as directed.

M & L for providing precast cement concrete solid building blocks masonry exc 10 cm width, type C1, 1:3:6 using 20mm graded aggregate and setting in CM 1:6 complete all as specified and as directed by Engr-in-Charge.

M & L for machine cut cudappah stone slab 20-25 mm thick over cement screed base, laid & jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and as directed by Engr-in-Charge.

M & L for 20 mm thick Granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window cills, cooking platforms and like in cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite over and including 15mm thick screed bed or bedding layer in cement mortar (1:6) all as specified and directed.

S & F in repairs vitrous china wash basin coloured oval type 560 x 410 mm complete but excluding pillar taps all as specified and as directed. MAKE: Hindware Cat No 10017 starwhite or equivalent makes as specified here-in-after.

S & F in repairs vitrous china squatting pan of pattern "long pan", size 630 mm white with 'P' or 'S' trap, front or back inlet and foot rests, any pattern water closet including pipe & seat cover complete all as specified and as directed.

S & F in repairs vitrous china squatting pan, orissa pattern, size 630 x 450 mm white, with integral foot rests water closet etc complete all as specified and as directed.

S & F in repairs PVC low level flushing cistern white 10 litres capacity and connections to pipe all as specified and as directed.

S & F 32 mm bore high density polyethylene pipes (HDPE) of pressure rating 6 Kgf/Sqcm inclluding bends, elbows, tees etc and fixing materials i.e. HDPE/PVC gum laid in trenches complete all as specified and as directed.

S & F in repairs brass chromium Plated Health faucet with spring pipe all as speified and as directed. MAKE: Jaquar Cat No ALD-CHR-585 or equivalent make as specified here in after.

S & F towel rail 600 mm long brass Chromium plated all as specified and directed. MAKE : Jaquar cat No CAN -1111N or equivalent in makes as specified hereinafter

S & F in repairs stop valves, cast copper alloy fancy type chromium plated, screwed down high pressure with crutch or butterfly handle screwed both ends for iron pipe of 15 mm bore all as specified and as directed

S & F in repairs bib taps, long neck type, cast copper alloy fancy type, chromium plated with crutch or butter fly handle, screwed for iron pipe15 mm bore all as specified and as directed. MAKE: Jaquar Cat No CON-107KN or equivalent make as specified here in after.

S & F in repairs pillar taps, cast copper alloy fancy type, chromium plated with capstan heads screwed down high pressure with long screwed shanks and fly nuts, screwed for iron pipe15 mm bore all as specified and as directed.

S & F in repairs mild steel Chromium Plated grating 125 mm dia suitable for Nahani trap complete all as specified and as directed.

S & F PVC connection 15 mm size with PTMT nuts of length 450 mm long with brass ferrules on both ends all as specified and directed.

S & F 75 mm dia PVC (SWR) nahani trap plain with grating incl jointing with solvent cement all as specified and as directed.

S & F 75 mm dia PVC (SWR) pipes single stacked in any length laid in floor all as specified and as directed.

All as per item No 26 herein above but 110 mm dia all as specified and as directed.

S & F PVC (SWR) bends 110 mm dia bore any radius with access door all as specified and as directed.

S & F PVC (SWR) bends 75 mm dia bore any radius with access door all as specified and as directed.

S & F in repairs solid PVC door frame of size 50 mm x 47 mm made out of 10 mm plain colour PVC sheet reinforced with MS square tube, supplying & fixing in opening as per specification & drawing shown on Page No. 160 of SSR Part II, 2010 complete all as specified and as directed.

S & F in repairs factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of MS tube for top and bottom rails. MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side & as gap insert for top rail & bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded/ sealed to the stiles & rails with suitable PVC sheet beading and joined together with solvent cement, supplying & fixing in the frame at site as per specified and as directed by Engr-in-Charge.

S & F in repairs butt hinges medium weight cold rolled mild steel 100 mm long all as specified and as directed.

S & F in repairs aluminium anodised barrel tower bolts of extruded section 100 mm long all as specified and as directed.

S & F in repairs Aluminum alloy, anodised, sliding door bolt 250 mm long and not less than 12 mm dia with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded sections or cast aluminium alloy all as specified and as directed.

S & F in repairs aluminium alloy anodised handle, cast type 100 mm long all as specified and as directed.

M & L for preparation of old decorated wall/ ceiling surfaces and applying one coat of Acrylic washable distemper complete all as specified and as directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc) or insulation boards/ slabs/ blankets, any thickness including cover fillets complete all as specified and as directed.

S & F 12 mm thick gypsum board in ceiling suitably placed in false ceiling grid made of aluminium of size 600 x 600 mm complete all as specified and as directed.

S & F anodised aluminium snap grid frame work for false ceiling Tee of size 24 x 28.5 mm made out of PGI sheet 0.3 mm thick double at web and single at flange, flange covered with powder coated sheet 0.25 mm thick and wall angle 24 x 24 x 0.45 mm powder coated for ceiling complete all as specified and as directed.

S & F hangers 6 mm dia GI (upto 1200 mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40 x 3 mm size 60 mm long complete all as specified and as directed.

Excavating in trenches, n exc 1.5 m wide and n exc 1.5 m in depth; for foundation, etc. or for shafts, wells, cesspits, manholes, pier holes, etc. n exc 10 Sqm on plan and getting out in hard/dense soil complete all as specified and directed.

Removing excavated material exc 250 m but n. exc 500 m and deposited where directed at a level not exc 1.5 m above the base as in soil.

Returning, filling in soil including spreading, levelling, watering and well ramming in layers n.exc. 25 Cm all as specified & directed.

M & L Moorum/red bajri filling in floors or pavings, laid in layers n exc.15 cm thick spread, levelled and rammed including watering complete all as specified and directed.

M & L for hardcore of gauge n.exc 63 mm, deposited, spread and levelled in layers n.exc 15 cm thick, watered and rammed to a true surface complete all as specified and directed.

M & L plain cement concrete 1:4:8 type D2 using 40 mm graded stone aggregate as in foundation & filling in Mass concrete complete all as specified and directed.

M & L plain cement concrete 1:3:6 type C2 using 40 mm graded stone aggregate as in foundation & filling in Mass concrete complete all as specified and directed.

M & L for providing cement concrete, 75 mm thick, type D-2, 1:4:8 (using 40 mm graded aggregate) as in sub base or sub floor etc. all as specified.

M & L for Screed bed or bedding layer of mortar 20 mm thick in CM 1:6 for laying floor finishes complete all as specified and directed.

M & L for Chequered cement concrete tiles 20 cm x 20 cm x 25 mm thick, set, jointed and pointed in near cement slurry in floors with grey cement and pigment complete all as specified and directed

M & L for providing cement concrete type C1 1:3:6 ( 20 mm graded aggregate) as in lintels upto 1.5 m clear span, cills, steps; seismic and other similar bands, plinth courses, string courses, lacing courses, parapets and railings upto 60 cm in height, copings, kneelers, apex stones, bed plates, water troughs and the like including weathering, slightly rounded for chamfered angles and throating, complete as directingall as specified and directed.

M & L for rendering 15 mm thick plaster in CM 1:4 in two coats (10 mm thick backing coat + 5 mm thick finishing coat )on concrete surfaces of walls finished even and smooth without using extra cement complete all as specified and directed.

M & L for preparation of new plastered surfaces of walls of any description including and applying two coat of weather proof exterior emulsion paint and over a coat of primer complete all as specified and directed.

M & L Steel work in tubular trusses, purlins,rafter etc.including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161-1979 grade St.-240 complete all as specified and directed

M & L pre-painted galvalume aluminium zinc coated GI based aorrugated steel sheet 0.5 mm thick of an colour having tensile strength og 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws complete all as specified and directed

M & L for applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer including preparation of new steel surfaces of any description exc 10 cm in width or girth complete all as specified and directed

M & L for point wiring 1100 Volts grade 1.5 Sqmm two single core PVC insulated FRLS unsheathed cable with stranded copper conductor conforming to IS:694:1990 with ISI marking drawn through and including suitable size PVC non metallic conduit with all accessories, including suitable size sunk pressed steel or cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover fixed flush with wall surface by means of brass screws and sunk cup washers for mounting of switches, sockets, fan regulators etc, including 1.5 Sqmm PVC insulated FRLS unsheathed 1100 Volts multistranded copper conductor conforming to IS:694:1990 with ISI marking as earth wire connected to metallic bodies of luminaries/ fan etc. at one end and to common earth dolly at other end, all as specified and directed for the following:-

(a) One light/fan point controlled by one switch

(b) One 3 pin socket outlet 5 Amp on same board with other switches.

All as per item no 57.00 above but with cable 4.0 Sqmm for one 3 pin socket outlet 15 Amps independent complete all as specified and as directed.

S & F MCB SPN, 5 to 32 Amps, 230 Volts, single phase, 10 KA capacity complete all as specified and as directed.

S & F MCB SP, 6 to 40 Amps, 230 Volts, single phase, 10 KA capacity complete all as specified and as directed.

S & F ceiling rose surface bakelite 65 x 50 mm three terminal complete all as specified and as directed.

S & F 5 star rated ceiling fan 1200 mm sweep assembling at site including electric connection from ceiling rose to connector with flexible cord twin core twisted copper of size 23/0.0076 and testing complete all as specified and as directed. MAKE: Havells Model ES NEO 5 star rating velocity HS 3 blade ceiling fan or equivalent in Crompton Greaves/Bajaj/Usha

Supply and fix ceiling fan regulator, electronic five step type, 230 Volts single phase all as specified and directed. MAKE : Anchor Penta Cat No 14502 or equivalent in Legrand / Havells / C&S

M & L for submain wiring with 2 runs of 4.00 Sqmm single core copper conductor PVC insulated cable and 1 run of 2.5 Sqmm single core copper conductor insulated cable as earthing lead drawn through existing conduit/ casing caping all as specified and as directed. NOTE: 2 runs of cable 4.00 Sqmm and 1 run of cable 2.5 Sqmm together will be measured as one unit length

S & F MCB DB SPN 240 Volt 4 way double door powder coated sheet steel enclosure for surface mounting fitted with 200 Amps bus bar and din channel complete all as specified and as directed.

S & F switch piano 5 Amps one way flush type multipurpose, ISI marked all as specified and as directed.

S & F socket outlet 5 pin, 5 Amps flush type multipurpose, ISI marked all as specified and as directed

S & F switch socket outlet 5 pin 15 Amps, flush type multipurpose, ISI marked all as specified and as directed

S & F LED tube light fittings 22 W decorative ultra slim aluminium square profile LED lighting fixture with high lumen output, environment friendly, energy efficient ready to use pack all as specified and as directed. MAKE: Havells Cat No. LHEXACP7in1A024 Code 9405 or equivalent in Bajaj/ CG/ Phillips

Taking down carefully copper/aluminium point wiring (light, fan, socket and power) complete(fittings to be measured separately) and making good surfaces of walls/floors etc complete all as specified and directed.

M & L for surface point wiring 1100 Volts grade 1.5 Sqmm PVC insulated FRLS unsheathed cable with multistranded copper conductor conforming to IS:694:1990 with ISI marking in and including PVC casing & caping medium grade with all accessories in wall/ceiling /floor/roof etc, sunk pressed steel or cast iron terminal boxes with 3 mm thick plastic laminated sheet top cover including 1.5 Sqmm PVC insulated FRLS unsheathed 1100 Volts multistranded copper conductor conforming to IS:694:1990 with ISI marking as continuous earth wire connected to common earth dolly all as specified and directed for the following:-

(a) One light/fan point controlled by one switch

(b) One 3 pin socket outlet 5 Amp on same board with other switches.

M & L for point wiring complete for one socket outlet 15 Amps on an independent board with FRLS, PVC insulated and unsheathed cable 4.0 Sqmm nominal area multi stranded copper conductor single core conforming to IS:694:1990 with ISI marking including PVC casing & caping pressed steel or cast iron terminal boxes not less than 2 mm thick of required size (factory made) including painting terminal boxes inside and outside with two coats of synthetic enamel paint over a coat of red oxide primer and with top cover 3 mm thick of plastic laminated sheet of required colour, complete with all accessories and including FRLS PVC insulated and unsheathed cable 4.0 Sqmm nominal area multi stranded copper conductor single core conforming to IS:694:1990 of green colour as earth wire to common earth and connected to earth dolly drawn in same concealed conduit and controlled by one 15 Amp switch complete all as specified and as directed.

M & L for submain wiring with 4 runs of 10.00 Sqmm single core copper conductor PVC insulated cable and 2 runs of 6.0 Sqmm single core copper conductor insulated cable as earthing lead drawn through existing conduit/ casing caping all as specified and as directed. NOTE: 4 runs of cable 10.00 Sqmm and 2 runs of cable 6.0 Sqmm together will be measured as one unit length

S & F modular switch 1 way 6 Amp, 1 module, ISI marked all as specified and as directed.

S & F modular socket 6 Amp, 2/3 pin combined 2 module, ISI marked all as specified and as directed.

S & F switch modular socket 6/16 Amp, 2/3 pin combined 2 module, ISI marked all as specified and as directed.

S & F modular white cover plate with frame, 8 module all as specified and as directed.

S & F modular white cover plate with frame, 2 module all as specified and as directed.

Fixing only in repairs modular switch 1 way 6 Amp, 1 module, ISI marked all as specified and as directed.

Fixing only in repairs modular socket 6 Amp, 2/3 pin combined 2 module, ISI marked all as specified and as directed.

Fixing only in repairs switch modular socket 6/16 Amp, 2/3 pin combined 2 module, ISI marked all as specified and as directed.

Fixing only in repairs modular white cover plate with frame, 8 module all as specified and as directed.

Fixing only in repairs modular white cover plate with frame, 2 module all as specified and as directed.

S & F LED tube light alongwith fixture, 24 W decorative ultra slim aluminium square profile LED lighting fixture with high lumen output, environment friendly, energy efficient ready to use pack all as specified and as directed. MAKE: Havells/ Bajaj/ CG/ Phillips

S & F in repairs exhaust fan 230 mm sweep all as specified and as directed. MAKE: Havells/ Bajaj/ CG NOTE: Old UNSV exhaust fans shall be deposited to MES store yard.

S & F MCB SPN, 40 Amps, 230 Volts, single phase, 10 KA capacity complete all as specified and as directed.

M & L for earthing complete with galvanized steel earth electrode 60 cm x 60 cm x 6 mm thick buried directly in ground(earth pit not less than 2.25m deep below ground level) with top edge of the plate not less than 1.5m below normal ground level, connected to galvanized iron wire 4.0 mm as earthing lead by means of nuts, bolts, checknuts and washers of galvanized iron or steel as shown in electrical plate no 3 of SSR-Part 1 of 2009 connected to earthing test point including testing on completion all as specified and as directed. NOTE: The unit rate shall be deemed to include for necessary excavation and earth work, GI pipe light grade 15 mm bore for protection of GI wire from earth electrode to and including the earth test point of galvanized iron/ steel of size 75 x 75 x 25 mm, supplying and laying charcoal dust, common salt, PCC 1:2:4 type B-1 chamber and MS angle iron frame 40 x 40 x 3 mm and RCC cover 40 mm thick (1:2:4) type B-1 using 20 mm graded stone aggregate reinforced with 6 mm dia round bars @ 75 mm C/C both ways with MS handle 12 mm dia, PGI funnel and wire mesh, 20 mm dia GI pipe light grade for watering all as shown in electrical plate no 3 of SSR-Part 1 of 2009 connected to earthing test point including testing on completion all as specified and as directed. Cost of earthing lead upto 7.5 m shall be included in the cost of this item.

S & F in repairs efficient 30 W LED recessed 2 x 2 luminaire including all accessories complete all as specified and as directed. MAKE: Bajaj Cat No BZRSQL 30W Gzi WH or equivalent in Havells/ CG/ Philips.

Taking down carefully existing rolling shutters of any size with motors and making good to disturbed surfaces all as specified and as directed.

S & F aluminium shutter slats single wall unperforated slats BAMS67 67 mm extruded aluminium singe layer slat of following sizes/ specifications all as specified and as directed: (a) H 19.5 Feet x 14.3 Feet = 278.85 Sqft. HSN code 8302 (b) H 16.5 Feet x 11.5 Feet = 189.75 Sqft. HSN code 8302 (c) S & F automatic motorised system of 600 Kg lifting capacity with remote system ISO certified - 02 Nos (d) Drum shaft pipe, side plate, bearing, plunges and fitting accessories complete as specified and as directed.

S & F single pole and neutral enclosure with a two pin and earth plug and socket complete with one double pole MCB 240 V, 20 Amps all as specified and as directed.

S & F wiring for circuit/ sub main wiring alongwith earth wire with 4 x 2.25 Sqmm and 2 x 1.5 Sqmm earth wire of FR PVC insulated copper conductor, single core cable in surface/ recessed as required in PVC casing caping complete all as specified and as directed.

Supply, laying, jointing, testing and commissioning of LT underground XLPE insulated, screened, PVC bedded, galvanised of wire armoured heavy duty electric cable, 1100 Volts of cross sectional area 16 Sqmm 4 core, conforming to IS: 7098 (Part-I) of 1988, laid in trenches/ wall/ floors/ ducts etc fixed with saddle and clamps or passing through pipes with cable and connection with proper thimbals, nuts, bolts and washers all as specified and as directed.

ABDUL RAHIM

Bidder Name

ABDUL RAHIM

M/S KAMALKANTH NAIK