ADDITION/ ALTERATION/ IMPROVEMENT OF SMQS AT AF STATION PUNE

Amount

Dismantling of floor hearth or wall tiling including cement mortar bedding (but not backing) and removing rubbish off the premises complete all as specified and directed.

Demolition of cement concrete (un-reinforced) in ground floors and pavings not exceeding 15 cm thickness (below or above ground level) complete all as specified and directed.

Material and labour for cement concrete type B0, 1:2:4 (using 12.5 mm graded aggregate), 25 mm thick as in sub floors complete all as specified and directed.

Material and labour for 15 mm thick screed bed or bedding layer for laying floor finishes in CM 1:6 complete all as specified and directed.

Material and labour for non-skid ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.06 sqm but not exceeding 0.11 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of tile over and including 15 mm thick screed bed in CM 1 6 complete all as specified and directed.

Material and labour for non-skid joint free coloured ceramic tiles 7 to 8 mm thick (square/ rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm in floors and of superior/ premium quality, set and jointed in neat cement slurry and pointed in colour cement to match the shade of tile over and including 15 mm thick screed bed in CM 1: 6 complete all as specified and directed.

All as per item no. 6 above but as in skirting/ dados over and including 10 mm thick rendering in CM 1:4 complete all as specified and directed.

Material and labour for joint free glazed ceramic coloured tiles, 450x300x7mm thick in size, set on vertical surfaces such as skirting, dado, etc., over and including 10 mm thick rendering in CM 1:4 set and jointed in neat cement slurry and pointed in white or coloured cement to match the shade of the tiles complete all as specified and directed.

Material and labour for machine cut kota stone slab flooring 18-20 mm thick over cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing complete and including screed bed 15 mm thick in CM1:6 complete all as specified and directed.

Material and labour for machine cut kota stone slab 18-20 mm thick in riser of steps, skirting, dado and pillar laid over cement screed and jointed with 10 mm thick plaster in CM 1:4 complete all as specified and directed.

Material and labour for granite (of any type) work (table rubbed and polished), 18-20 mm thick in steps, jambs, pillars, window cills, cooking platform and like in CM 1:4 including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite complete all as specified and directed.

Material and labour for rounding to edges of stone slabs one edge, such as in steps, cooking platform and other similar situations complete all as specified and directed.

Taking up or down steel tubing and connections of 15 mm bore, including cleaning for re-fixing or removal complete all as specified and directed.

Taking up or down steel tubing and connections of 20 mm bore, including cleaning for re-fixing or removal complete all as specified and directed.

Supply and fixing GI tubing, medium grade of bore 15 mm with all fittings, fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Fixing only 15 mm dia tubes any grade to walls and ceiling or laid in floors complete all as specified and as directed.

Supply and fixing GI tubing, medium grade of bore 20 mm with all fittings and fixed complete to walls and ceiling or laid in floors complete all as specified and directed.

Fixing only 20 mm dia tubes any grade and fixed to walls and ceiling or laid in floors complete all as specified and as directed.

Cutting of existing steel tubing for alterations or additions (each cut to be measured) for 15 mm bore pipe complete all as specified and directed.

Cutting of existing steel tubing for alterations or additions (each cut to be measured) for 20 mm bore pipe complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required for concealed water tubing and making good, cutting not exceeding 10 cm girth in stone/ concrete walls complete all as specified and directed.

Supply and fix in repair vitreous china, squatting pan of 'Orissa' pattern, long pan, size 580 mm x 440 mm, white, with 'P' of 'S' trap, flush pipe, front or back inlet and foot rests any pattern, including connection to trap and to flushing pipe, anti-syphonage pipe, etc. complete including making good to concrete floor complete all as specified and directed.

Supply and fix in repair 15 mm dia PVC connection 60 cm long including check nuts etc. complete all as specified and directed

Supply and fix in repair 15 mm bore bib tap, chromium plated, cast copper alloy with wall flange complete all as specified and directed.

Dismantling PVC water tanks exceeding 250 litre and not exceeding 500 litre capacity complete all as specified and as directed.

Supply and fix rotational moulded polyethylene double layer water storage tank of 500 litres capacity, ISI marked (cylindrical vertical with closed top) hoisted and fixed in position all as specified in SSR Pt-I with 25 mm ball valve, high pressure, PTMT with rod and high density plastic ball complete all as specified and directed.

Cleaning and removing all scale and dirt etc., from tanks and from mouths of circulating pipes, etc. for tank of capacity exceeding 250 litre and not exceeding 500 litre complete all as specified and directed.

Supply and fix in repair 10 litres capacity PVC flushing cistern, low level, white and ISI marked, with inlet, ball valve, float chain, handle including 32 mm PVC flush pipe complete all as specified and as directed.

Supply and fix in repair vitreous china wash hand basin, white, 550 mm x 400 mm flat back, including providing CI brackets, CP pillar tap, PVC waste pipe 32 mm dia, chromium plated brass waste coupling complete all as specified and as directed.

Supply and fix in repair angle valves, fancy type, cast copper alloy, screwed down, high pressure, with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed complete all as specified and as directed.

Supply and fix sheet glass shelf assembly consisting of 5.5 mm thick sheet glass shelf 12 cm wide with chromium plated bracket guard and railing 60 cm long complete all as specified and directed. Make: Prayag Cat Part No. BEA-46 or equivalent in Hindware/ Jaquar

Supply and fix in repair brass chromium plated tubular towel rail, 20 mm dia, D type, 60 cm long between flanges complete all as specified and directed.

Supply and fix in repair 20 mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipe and fixed complete all as specified and directed.

Supply and fix in repair brass chromium plated shower rose 125 mm size with or without swivel joints, any size, including fixing to steel pipe or union complete all as specified and directed.

Supply and fix in repair 15 mm dia stop valves cast copper alloy, screwed down, high pressure with crutch or butterfly handle, screwed both ends for iron pipe or for unions and fixed (concealed type) complete all as specified and directed.

Supply and fix in repair sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes; including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets, waste pipe and coupling and connecting union to pipe, overall size 915mm x 460mm and bowl size 410mm x 330mm x 160mm complete all as specified and as directed.

Supply and fix towel ring of chromium plated, fixed with and including chromium plated brass screws and wooden/ plastic cleats (minimum weight 90 gm) complete all as specified and directed.

Supply and fix chromium plated soap case complete all as specified and directed. Make: Prayag Cat Part No. BA-15S or equivalent in Hindware/ Jaquar

Supply and fix stainless steel kitchen plate rack 0.65 mm thick with plugs, washers etc., overall size 610mm x 760mm x 254mm complete all as specified and directed. Make: Prayag Cat Part No. P-330 or equivalent.

Demolition and breaking up drain pipes (salt glazed ware/ PVC/ AC/ reinforced concrete) upto 150 mm dia set in cement mortar complete all as specified and directed.

Supply and fix 75 mm dia PVC (SWR) grade single socketed pipes in any length complete with rubber ring joints laid in trenches including necessary earthwork or in floors complete all as specified and directed.

All as per item no. 42 above but 110 mm dia.

Supply and fix PVC (SWR) bends of any radius with oval and access door of 75 mm dia complete all as specified and directed.

All as per item no. 44 above but 110 mm dia.

Supply and fix 110 mm dia PVC (SWR) branch piece, double (double Y), equal or unequal with acess door complete all as specified and directed.

Supply and fix 110 mm dia PVC (SWR) junction single T, equal or unequal with acess door complete all as specified and directed.

Supply and fix PVC (SWR) vent cowl of 110mm dia complete all as specified and directed.

Demolition of wall and ceiling boards (fibre, pulp, insulation, etc.) or insulation boards/ slabs/ blankets, any thickness, including cover fillets complete all as specified and directed.

Material and labour for fixing in repair 4 mm thick non-asbestos fibre cement building boards fixed or laid/ inserted to timber/ GI/ Aluminium framework with screws complete all as specified and directed. Make: Everest/ Armstrong

Material and labour for anodised aluminium snap grid of size 605 mm x 605 mm frame work for false ceiling and hangers 6 mm dia G. I. (upto 1200mm length) adjusting level fixed to roof slabs by means of ceiling cleats made out of GI flat 40x3 mm size 60 mm long and expansion hold fasteners 12.5 mm dia 40 mm long complete all as specified and directed. Make: Everest/ Armstrong

Dismantling of single layer mangalore pattern or similar tiles in roofing complete all as specified and directed.

Dismantling of asbestos cement (corrugated, semicorrugated, etc.) sheets in roof coverings complete all as specified and directed.

Dismantling of battens for tiles, shingles etc., of any size not exceeding 15 cm including tilting fillets complete all as specified and directed.

Dismantling timber scantlings 40 sq.cm and over in section, framed work in any position spaced not exceeding 15 cm complete all as specified and directed.

Supply and fix rolled mild steel as in roof trusses (framed), purlins (angle, beam, tee channel) including distance piece, cleats etc. of Fe-410W (Gde E-250, quality A) with and including necessary cutting, bending, drilling holes, welding, rebates etc., complete all as specified and directed.

Supply and fix rolled mild steel sections as in main and cross beams, hip and jack rafters; purlins where connected to common rafters and running rails and guides for sliding doors; fixed with angle cleats or other connecting plates etc. of Fe-410W (Gde E-250, quality A) with and including necessary cutting, bending, drilling holes, welding, rebates etc., complete all as specified and directed.

Material and labour for plain cement concrete type B1 1:2:4 using 20mm graded stone aggregate as in copings complete all as specified and directed.

Supply and fix pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Supply and fix pre-painted galvalume aluminum zinc coating GI based plain steel sheet 0.50 mm thick of any colour having tensile strength of 550 Mpa as in roof covering/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

Taking down chowkhats or frames exceeding 1.5 sqm and not exceeding 4 sqm each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down chowkhats or frames not exceeding 1.5 sqm each with shutters (without taking off shutter from the frame) complete all as specified and as directed.

Taking down shutters of any description exceeding 1 sqm and not exceeding 2 sqm complete all as specified and as directed.

Taking down shutters of any description not exceeding 1 sqm complete all as specified and as directed.

Supply and fix factory made solid panel PVC door shutter 30 mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails, M.S. frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20 mm width stuck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail and bottom rail on either side and as gap insert for top rail and bottom rail; panelling of plain colour PVC sheet to be fitted in the M.S. frame welded/ sealed to the stiles and rails with suitable PVC sheet beading, and joined together with solvent cement, supplying and fixing in the frame at site as per specification and drawing complete all as directed .

Supply and fix solid PVC door frame of size 50 mm x 47 mm, made out of 5 mm thick plain colour PVC sheet, reinforced with mild steel square tube complete all as specified and as directed.

Supply and fix stainless steel butt hinges, 100 mm long complete all as specified and as directed.

Supply and fix 100 mm size butt hinges, medium weight, cold rolled mild steel, and fixed complete all as specified and directed.

Supply and fix continuous (piano) hinges 30 mm width flaps, mild steel, bright finish or electro galvanised complete all as specified and directed.

Supply and fix 150 mm long, aluminium barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 100 mm long, aluminium barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix 150 mm size extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and fix 300 mm long mild steel sliding door bolt, plate type, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Supply and fix floor door stopper of aluminium alloy body and tongue, anodised, with hard drawn steel spring, overall length 150 mm fixed in floor complete all as specified and directed .

Supply and fix 300 mm, mild steel ordinary rat tail rod pattern helical door springs including roller and roller plate complete all as specified and directed.

Supply and fix 125 mm hasp and staple, safety type, brass, with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and directed.

Supply and fix second class hardwood plain, solid, straight chowkhats and frames, wrought, framed rebated on the solid, rounded or chamfered put together with glue pinned at joints complete all as specified and directed.

Material and labour for 165mm x 60mm pressed steel frames for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc., complete all as specified and directed.

Material and labour for 105mm x 60mm pressed steel frame for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc., complete all as specified and directed.

Material and labour for providing cement concrete type C1 1:3:6 using 12.5 mm graded aggregates for chowkhat filling and hold fast as required cmplete all as specified and directed.

Material and labour for factory made 35 mm thick glazed and skeleton shutters made of 2nd class hard wood, open rebated and prepared to receive glass gauge edges of framing plain chamfered or rounded, fitted with cut and mitred beads for securing glass etc. for window, ventilator shutters, etc. as specified in SSR Part I, Section 8 clause 8.24(b) and fitted to chowkhat complete all as specified and directed .

Material and labour for factory made 35 mm thick flush shutters, solid core construction, with block board core and plywood face panels, commercial type on both sides, supplied and fitted to chowkhats complete all as specified and directed .

Taking down shutters of any description exceeding 1 sqm and not exceeding 2 sqm each and refixing in other opening complete all as specified and directed.

Hacking out old broken glass (any thickness, size, quality or description) from wooden frames or stone, concrete or brick surrounds, glazed with putty or fixed with beads complete all as specified and directed.

Supply and fix 3 mm thick sheet glass, ordinary quality and glazing with oil putty in squares not exceeding 0.5 sqm in each pane complete all as specified and directed.

Supply and fix 3 mm thick figured glass ordinary quality and glazing with oil putty in square not exceeding 0.5 sqm in each pane complete all as specified and directed.

Supply and fix galvanised mild steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and directed.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded including taking down complete all as specified and directed.

Supply and fix steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete without glazing bars, dovetailed or welded complete all as specified and directed.

Supply and fix steel windows or ventilators with top hung shutter including hinges, steel peg stay, with glazing bars complete all as specified and directed.

Material and labour for 18 mm thick block boards, fixed in repair, grade 2 quality, interior grade, commercial type, fixed with screws to timber and nails for storage almirah to the size and pattern as shown in drawing complete all as specified and directed.

All as per item no. 91 above but 12 mm thick.

Material and labour for 0.90 mm thick decorative laminate type-1 of surface finish (colour and pattern as approved) fixed with approved adhesive as per manufacturer’s instruction finished to approved size for working table complete all as specified and directed.

Material and labour for 2nd class hardwood plain cover fillets square, rectangular or triangular in section bull nosed, splayed, chamfered or rounded on one edge or face sectional area not exceeding 6 sqcm complete all as specified and directed.

Supply and fix in repair 150 mm long aluminium, barrel tower bolts of extruded section complete all as specified and directed.

Supply and fix in repair 150 mm size handles, extruded aluminium alloy handles, fabricated type, anodised complete all as specified and directed.

Supply and fix in repair 100 mm size butt hinges, heavy weight, cold rolled mild steel, and fixed complete all as specified and directed.

Supply and fix in repair 250 mm long aluminium anodised sliding door bolt, plate type, with bright bolt not less than 12 mm dia with and including a minimum of 6 bolts and nuts, four on bolt plate and two on staple plate and fixed complete all as specified and directed.

Supply and fix stainless steel harrison rail 20 mm dia (curtain rod) complete all as specified and directed.

Supply and fix fancy type CP brackets for curtain rods with 1mm thick plate complete all as specified and directed.

Material and labour for 75 mm thick PCC 1:3:6 type C-2 using 40 mm graded stone aggregate as in sub base of floor and path, plinth protection etc. complete all as specified and directed.

Material and labour for forming contraction (dummy) joints 30 mm deep x 10 mm wide for plinth protection and similar work, filled with sealing compound grade 'A' complete all as specified and directed.

Material and labour for precast solid cement concrete block masonry exceeding 10 cm in width built with solid blocks of type C1 1:3:6 mix using 20 mm graded stone aggregate and set in CM 1:6 complete all as specified and directed.

Taking down cement plaster on brick/ stone/ concrete surfaces including wall tiling and hacking out joints, hacking for key, scrubbing down with water etc. complete all as specified and directed.

Material and labour for rendering 15 mm thick on surface of brick work/ concrete surfaces in CM 1:6, finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for 5 mm thick cement plaster in CM 1:3 on fair faces of brick or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Material and labour for 10mm thick cement plaster in CM 1:4 on fair faces of brick or concrete surfaces and finishing the surface even and smooth without using extra cement complete all as specified and directed.

Raking out joints/ pointing cement mortar to random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and directed.

Material and labour for keyed pointing to random or polygonal rubble, uncoursed or brought upto course in CM 1:4 complete all as specified and directed.

Cutting down plants/ trees of girth not exceeding 15 cm, from roof/ top sides of external walls of buildings, in chajjas, wall junctions, junctions of GI/ CI/ AC/ PVC pipes and taking out roots entered in walls/ slabs, applying emulsion of non toxic chemicals including making good the surface using PCC 1:2:4 type B1 or cement mortar (1:2) or brick work in CM 1:4 plastered with CM 1:4 to match with existing surface and repairing the pipes and joints which was affected by cutting down/ taking out process all as specified and as directed for plants/ trees located upto a height of 7.50 mtrs from GL etc. complete all as specified and directed.

Demolition of stone/ block masonry built in cement mortar including all quoins, arches, pillars,etc. complete all as specified and as directed.

Material and labour for walling of random rubble, uncoursed, well bonded, bedded and solidly hearted, for random or polygonal rubble walling, brought up to course built in cement mortar 1:4 complete all as specified and directed.

Material and labour for reinforced cement concrete (nominal mix) type B0 1:2:4 using 12.5 mm graded aggregate as in slabs supported on walls, beams and columns in floors, roofs, landings, balconies, canopies, deck slabs and in shelves and the like complete all as specified and directed.

Material and labour for mild steel TMT bars 10 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Material and labour for chimney bars (straight or camber); bearing bars; tongues or water bars for window frames; window guard bars, plain, let in and fixed independently in wooden frames, L or T section supports for shelves etc. and similar articles conforming to Fe-290 Gde E-165 complete all as specified and directed.

Material and labour for use and waste of flat formwork to sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelve including supports, overhangs, etc. also splays between floors and beams, etc. for rough finished surfaces of concrete complete all as specified and directed.

Material and labour for preparation of old painted wooden surfaces of any description having width/ girth exceeding 10 cm and applying one coat of synthetic enamel paint complete all as specified and directed.

Material and labour for preparation of new wooden surfaces of any description having width/ girth exceeding 10 cm and applying two coats of synthetic enamel paint over pink primer complete all as specified and directed.

Material and labour for preperation of newly plastered surfaces of ceilings and applying three coats of white wash complete all as specified and directed.

All as per item no. 118 above but on walls.

Material and labour for preparation for wall care putty on wall and applying in three coats in three layers for smooth surface complete all as specified and directed.

Material and labour for complete removal of existing treatment of walls, plastered or unplastered, washing, rubbing down and applying two coats of distempering with first quality acrylic distemper over a coat of alkali resistant primer having VOC content less than 50 gm per ltr of approved manufacturer of required shade of colour as per manufacturer specifications complete all as specified and directed.

Material and labour for prepartion of newly plastered surfaces and applying two coats of distempering with first quality acrylic distemper over a coat of alkali resistant primer having VOC content less than 50 gm per ltr approved manufacturer of required shade of colour as per manufacturer specifications complete all as specified and directed.

Material and labour for preparation of old plastered surfaces/ unplastered surfaces including brooming down with steel wire, brushing, scrapping down smoke, spout, moulds, moss and efflorescence, salt treating oil and greasy spots etc., and applying two coats of white wash complete all as specified and directed.

All as per item no. 123 above but on surface of on ceiling/ soffits of slabs, chajjas complete all as specified and directed.

Material and labour for prepartion of newly plastered surfaces and applying two coats of 100% premium acrylic emulsion paint (weather proof) having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/10 sqm over new surfaces complete all as specified and directed.

Material and labour for complete removal of existing treatment of walls plastered or unplastered and applying two or more coats of 100% premium acrylic emulsion paint (weather proof) having VOC less than 50 gm/ litre and UV resistance as per IS 15489:2004, alkali and fungal resistance, dirt resistance exterior paint of required shade (Company Depot Tinted) with silicon additives @ 1.43 litre/ 10 sqm over and including priming coat of exterior primer applied @ 0.90 litre/ 10 sqm over surfaces complete all as specified and directed.

Preparation of new or previously untreated surfaces of steel of any description over 10cm in width or girth not otherwise described and applying two coats of synthetic enamel paint to steel surfaces over one coat of red oxide primer complete all as specified and directed.

Material and labour for preparation of old painted steel surfaces of any description of width/ girth exceeding 10 cm and applying two coats of synthetic enamel paint complete all as specified and directed.

Material and labour for 75mm thick PCC 1:2:4 type B2 using 40 mm graded stone aggregate as in sunken floor complete all as specified and directed.

Material and labour for PCC 1:5:10 type E2 using 40 mm graded aggregate as in foundations, filling and mass concrete complete all as specified and directed.

Material and labour for PCC 1:1½:3 or Bitumastic Gola with 80/25 bitumen and coarse sand mixture 1:3 by weight 8cm x 8cm, at the junction of roofing to vertical surface as in sunken or similar work complete all as specified and directed.

Material and labour for bitumen blown any grade applied hot, two coats to concrete bedding surface @ 1.5 Kg/Sqm per coat as in sunken floor complete all as specified and directed.

Material and labour for polythene flim black 50 micron laid in sunken floor complete all as specified and directed.

Material and labour for spout of 50 mm bore GI pipe and projection 450 mm clear from outer wall in any length or description with rubber ring joints and fixed in sunken floor etc. for drain out logging as in sunken floor etc. or similar work complete all as specified and directed.

Material and labour for 25 mm thick PCC 1:2:4 type B0 using 12.5 mm graded stone aggregate as in sunken floor mixed with water proofing compound and finished fair and even complete all as specified and directed. (Note:- WPC shall be measured and paid separately)

Dismantling stone slabs or roof treatment of any description in suspended slabs in roofs, suspended floors, chajjas, landings etc., including cement mortar, bedding but not backing and removing rubbish off premises complete all as specified and directed.

Material and labour for 10 mm thick rendering on fair faces of brick work/ concrete surfaces finished even and smooth without using extra cement in CM 1: 4 mixed with water proofing compound 200 ml per 50 kg bag of cement complete all as specified and directed. (Note:- WPC shall be measured and paid separately)

Material and labour for APP based polymeric membrane minimum weighing 3kg/sqm and minimum 3mm thick reinforced with polyster non-woven fabric (weight of reinforcement not less than 150 gms/ sqm) laid on primed surfaces by forced application including preperation and applying two coats of heat resisting aluminium paint over APP membrane complete all as specified and directed.

Supply only liquid waterproofing compound complete all as specified and directed.

Material and labour for PCC 1:2:4, 25 mm thick type B0 using 12.5 mm graded stone aggregate as in floor finished even and fair without using extra cement complete all as specified and directed.

Dismantling stone slabs and tiles of any description or thickness in floors, aprons etc. laid in any type of mortar complete all as specified and directed.

Material and labour for rough dressed 30 mm thick sand stone slab flooring, laid dry but bedded and jointed in cement mortar 1:6 and pointed in cement mortar 1:3 (except stone only) complete all as specified and directed.

Supply and fix in repair PVC (SWR) floor trap of diameter of outlet 75 mm including jointing to waste pipe and fixed in cement concrete type B1 1:2:4 complete all as specified and directed.

Supply and fix in repair PVC (SWR) gully trap 100 mm including setting and jointing with solvent cement complete all as specified and directed.

Supply and fix grating doom 100 mm dia of stainless steel with holes for waste pipes cement complete all as specified and directed. Make: Prayag Cat Part No. FT-06 or equivalent

Supply and fix grating doom 100 mm dia of stainless steel complete all as specified and directed. Make: Prayag Cat Part No. FT-05 or equivalent

Supply and fix in repair galvanised steel wire cloth 0.63 mm nominal dia of wire and average width of aperture 1.40 mm and fixed with tinned tacks, or galvanised wire staples complete all as specified and as directed.

Removing building materials etc. to a distance of 100 metre or under, beyond the lead included in the rates, including loading, unloading and stacking at the destination complete all as specified and directed.

Material and labour for forming jambs etc., to opening (to foregoing items), including cutting, toothing and properly bonding into work, also facing, jointing and pointing to match existing work in CM 1:4 complete all as specified and direted.

Supply and fix 75 mm dia of PVC (SWR) junction single T equal or unequal with access door complete all as specified and directed.

Material and labour for single pipe in toilet duct pipelines for soil water down take pipe, fixing done with pipe supporting clamping system consisting of profile bracket + continuous slotted C channel + U Bolt R/M system - one soil water pipe 4" PVC (110 mm) running vertically with wall distance 3", Pipe Support Clamping shall be made of the following: (i) Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. (ii) Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. (iii) U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty for one unit : (a) Profile Bracket Wall distance 3" - 2 Nos. (b) Continuous Slotted C Channel of Size 10" - 1 No.; (c) U Bolt R/M for 4" PVC (110 mm) Pipe Dia. - 1 No.; (d) Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing : CEAG/AR/TD/08R. Make: Shaivi or equivalent as approved by GE.

Material and labour for single pipe in kitchen duct pipeline for waste water down take pipe fixing done with pipe supporting clamping system consisting of profile bracket + continuous slotted C channel + U Bolt R/M system - one waste water pipe 2 1/2" PVC (75 mm) running vertically with wall distance 3": Pipe Support Clamping shall be made of the following: (i) Profile bracket having wall distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304, Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. (ii) Continuous Slotted "C" Channel with ribs to be used of size 10" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. (iii) U bolt R/M made of low carbon mild steel with rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty for one unit: (a) Profile Bracket Wall distance 3" - 2 Nos. (b) Continuous Slotted C Channel of Size 10" - 1 No.; (c) U Bolt R/M for 2 1/2" PVC (75 mm) Pipe Dia. - 1 No. (d) Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing : CEAG/AR/TD/08R. Make: Shaivi or equivalent as approved by GE.

Material and labour for two bathroom duct pipelines with two separate waste water down take pipe fixing done with pipe supporting clamping system consisting of profile bracket + continuous slotted C channel + U Bolt R/M system - Two Waste Water Pipe 2 1/2" PVC (75 mm) running with wall distance 3": Pipe Support Clamping shall be made of the following: (i) Profile Bracket having Wall Distance 3" made of Low Carbon Hot Roll Gauge Corrected (HRGC) Steel (IS 1079 DD); material size 32 mm x 3 mm with ribs and notch are Hot Dip Galvanzied + Zn Al Flake coated having Salt Spray Test (Test method - ASTM B-117-2019) result above 2000 hrs with SS304 Hex Flange Bolt with Serration 5/16 x 3/4 (A/F 13mm) as per DIN 6921and SS304 Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration as per DIN 6923. (ii) Continuous Slotted "C" Channel with ribs to be used of size 24" made of Low Carbon Hot Roll Gauge Corrected (HRGC) steel (IS 1079 DD) are Hot Dip Galvanzied + Zn Al Flake coated with material thickness of 3mm. (iii) U bolt R/M are made of low carbon mild steel with Rod diameter 7 mm approx.; Zn Al Flake coated with noise absorbing semi transparent ribbed silicon rubber sleeve; with Hex Flange Nut BSW 5/16 x 18 x 8 x 13 with Serration set as per DIN 6923 - Zn Al Flake coated. Hotdip Galvanizing: As per IS 2629 (1985) - 610 grams/m2 (> 85 microns). Material Grade : IS 1079 DD used as per MTC confirms to EN 10204 3.1. Material Qty. for one unit : (a) Profile Bracket Wall distance 3" - 2 Nos. (b) Continuous Slotted C Channel of Size 24" - 1 No.; (c) U Bolt R/M for 2 1/2" PVC (75 mm) Pipe Dia. - 2 No.; (d) Justi Khilla 2 1/2" Zn coated - 4 nos. Fixing Details: Pipe Support Clamping Unit to be fixed at every metre distance in the duct as specified in the Technical Drawing : CEAG/AR/TD/08R. Make: Shaivi or equivalent as approved by GE.

Material and labour for machine pressed precast conctete interlocking paver block any shape and size confirming to IS 15658-2006 of 60 mm thickness M-40 grade with grey cement and pigment complete all as specified and directed.

Material and labour for 25 mm thick sand filling under precast concrete inter locking paver floors or in foundations including watering and consolidation complete all as specified and directed.

Material and labour for 75 mm thick cement concrete type D2, 1:4:8 using 40mm graded aggregate for laying as in sub base complete all as specified and directed.

Material and labour for providing and laying at or near ground level factory made kerb stone of M-25 grade cement concrete in position to the required line, level and curvature, jointed with cement mortar 1:3 (1 cement: 3 coarse sand), including making joints with or without grooves (thickness of joints except at sharp curve shall not to more than 5 mm), including making drainage opening wherever required complete all as specified and directed.

Taking down the existing surface batten type point wiring of aluminium for light, fans, sockets, power sockets, staircase light point complete with switch socket regulator, bracket fitting etc. and making good disturbed surfaces for wall, floors etc. complete all as specified and directed. Note: Rate quoted shall include sorting out servicable and unservicable light fittings and keeping servicable fittings in safe guard for reuse as required on site after completion of civil work complete.

Taking down submain wiring of any dia/ sqmm on teak wood batten/ PVC conduit/ GI earth wire complete all as specified and directed.

Taking down carefully by unscrewing the unservicable distribution boxes, MC distribution boards SP and TPN with porcelain cutouts etc. complete all as specified and directed.

Fixing only servicable light fittings obtained from item no. 158 above including making connection after completion of civil work as required on site complete all as specified and directed.

Material and labour for providing point wiring complete with two runs of 1.5 sqmm single core multistranded copper conductor FRLS PVC insulated cable 1100 Volts grade and with one run of 1.5 sqmm single core multistranded copper conductor FRLS PVC insulated cable 1100 Volts grade wire for continuous earthing in and including PVC casing and capping/ conduit with all fittings/ fixtures etc. and recessed type metal box ISI marked (IS:14772) for housing switches/ sockets complete all as specified and directed for one light point controlled by one, one way switch. Note: Metal sunken box and top cover frame shall be measured and paid separately.

All as per item no.162 above but for one light point controlled by two, two way switches complete all as specified and directed.

All as per item no.162 above but for one bell point controlled by one, one way switches complete all as specified and directed.

All as per item no.162 above but for one exhaust fan/ wall mounted fan/ ceiling fan point controlled by one regulator/ switch complete all as specified and directed.

All as per item no.162 above but for one 3 pin 5 Amps socket outlet on independent board complete all as specified and directed.

All as per item no.162 above but for one 3 pin 5 Amps socket outlet on same board complete all as specified and directed.

Material and labour for providing point wiring complete with two runs of 2.5 sqmm single core multistranded copper conductor FRLS PVC insulated cable 1100 Volts grade and with one run of 2.5 sqmm single core multistranded copper conductor FRLS PVC insulated cable 1100 Volts grade wire for continuous earthing in and including PVC casing and capping/ conduit of 25 mm size with all fittings/ fixtures etc. complete for housing one 15Amp switch/ socket complete all as specified and directed. Note: Metal sunken box and top cover frame shall be measured and paid separately.

Material and labour for sub main wiring using two runs of 6 sqmm cable and one run of 6 sqmm earth wire with single core FRLS PVC insulated multistranded copper conductor 1100 volts grade, ISI marked complete with PVC conduit/ casing and accessories like bends, tees etc. complete all as specified and as directed. Note: One run of phase, one run of neutral and one run of earth wire with PVC conduit/ casing and capping shall be measured and paid as one unit length.

Material and labour for sub main wiring using two runs of 4 sqmm cable and one run of 4 sqmm earth wire with single core FRLS PVC insulated multistranded copper conductor 1100 volts grade, ISI marked complete with PVC conduit/ casing and accessories like bends, tees etc. complete all as specified and as directed. Note: One run of phase, one run of neutral and one run of earth wire with PVC conduit/ casing and capping shall be measured and paid as one unit length.

Supply and fix sheet metal enclosure with socket plug top, single pole and neutral enclosure with two pin earth plug and socket with one MCB SP of capacity 20 Amps complete all as specified and directed.

Supply and fix vertical double door distribution board TP 4 way with 125 Amp rated busbar consisting of one MCCB 63 Amp 18 kA including making necessary arrangement to fix DB surface mounted on wall and making good existing disturbed surface in all respect complete all as specified and directed.

Supply and fix sheet metal enclosure with MCB DB double door SPN 12 way 230 V with neutral link and with 200 Amp busbar including making necessary arrangement to fix DB surface mounted on wall and making good existing disturbed surface in all respect complete all as specified and directed.

Supply and fix in repair RCBOs SPN 40 Amp, 230 Volt, C series complete all as specified and directed.

Supply and fix in repair MCB SP, 240 Volt, 6- 32 Amp, C series complete all as specified and directed.

Supply and fix modular switch, one way, 1 module, 240 Volts, 6 Amps (ISI marked) complete all as specified and directed.

Supply and fix modular socket outlet, 2/3 pin, combined 2 module, 6 Amps complete all as specified and directed.

Supply and fix modular switch one way, 16 Amps, 1 module complete all as specified and as directed.complete all as specified and directed.

Supply and fix modular socket 6 Amp / 16 Amp, 2/3 pin combined 2 module complete all as specified and as directed.

Supply and fix ceiling rose surface type bakelite/ PVC three terminal, 65 x 50 mm, ISI marked complete all as specified and as directed.

Supply and fix modular bell push, 6 Amps, 1 module complete all as specified and directed.

Supply and fix bell electric 230 Volt, single pole complete all as specified and directed.

Supply and fix modular fan step regulator, 120 W, 2 module complete all as specified and directed.

Supply and fix modular switch, two way, 1 module, 6 Amps (ISI marked) complete all as specified and directed.

Supply and fix in repair LED light fitting mirror type with high output diffuser 2 feet, 10 Watt, 220 V AC decorative type with driver holder and LED lamp including connecting up with three core flexible copper conductor cable of suitable size complete all as specified and directed.

Supply and fix in repair indoor surface and wall mounted LED batten 20 W, extruded aluminium housing provided for efficient heat dissipation with polycarbonate diffuser and integrated electronic driver with industrial grade heavy duty driver having THD<10% complete with all accessories internally pre-wired and including connecting up with three core 0.5 sqmm flexible copper conductor cable ceiling rose to fitting terminal complete all as specified and directed.

Supply and fix in repair LED light fitting 1 x 10 W bulkhead luminaries including LED light driver holder and connecting up with three core flixible copper conductor cable complete all as specified and directed.

Supply and fix angle/ batten holder insulated body with back plate for batten fittings complete all as specified and directed.

Supply and fix exhaust fan, heavy duty, steel body, 300 mm sweep, voltage 230 V, 1200 RPM with copper winding complete with 4 blades, frame and louver shutter including making suitable hole in wall, anchoring and making good the disturbed surfaces complete all as specified and as directed.

Taking down ceiling fan single phase 240 V, 1200 mm / 1400 mm sweep from the existing position including disconnecting supply cable from ceiling rose/ connector and opening ceiling fan carefully and cleaning and washing the bearings/ bushes thoroughly and applying necessary lubricants, applying two coats of synthetic enamel paint on ceiling fan including 3 no.s blades, hanging rod etc. and hanging in original position connecting and testing complete on completion of civil works of building complete all as specified and directed. Note: Minor spares required for repair shall be measured and paid separately under respective items.

Supply and fix ball bearing 6202/ 6303 as required on site complete all as specified and directed.

Supply and fix bush required as per existing fan on site complete all as specified and directed.

Supply and fix ceiling fan capacitor 2.5 mfd/ 3.15 mfd as required on site complete all as specified and directed.

Taking down the existing street light fitting and supply and fix energy saving and environmental friendly lonf life LED street light fitting 35 Watt 230 V AC outdoor type with high pressure die cast aluminium hosing and heat resistance, impact and corrosion resistance including thermal management in multiple optics, IP 65/66 roadway luminaries with LEDs as light source and lens embedded PC cover/ toughened glass and impact resistance of IK07 and electronic driver fixed on pole/ wall with and including suitable dia size bracket as per manufacturer recommendation complete with MS flat iron clamps (clamp shall be 40x5 mm MS flat), nuts, bolts and washers including painting the clamps with a coat of aluminium paint over a coat of red oxide primer including connection complete all as specified and directed.

Material and labour for earthing complete with galvanised iron earth plate electrode 600 mm x 600 mm x 6 mm as earthing lead buried directly in ground vertically in a pit of depth not less than 2.25 metre below ground level with the top edge of earth plate at a depth not less than 1.5 m below normal ground level, connected to and including galvanised iron earth lead wire 4 mm dia as earthing lead by means of bolts, nuts, check nuts and washers of galvanised iron or steel, and connected to earthing test point, providing charcoal and common salt all as shown in electrical plate no. 3 of SSR part I, and testing on completion including excavation and earth work in any type of soil, PCC 1:3:6 type C1 earthing chamber, precast slab 50 mm thick in cement concrete 1:2:4 type B1 reinforced with welded steel wire fabric (XPM) weight not less than 4kg/sqm, funnel with wire mesh, watering pipe of 20 mm bore medium grade GI pipe and lugs, earthing wire protected by galvanised iron or steel pipe 15 mm dia medium grade 7.5 metre long complete all as specified and as directed.

Supply and fix modular PVC sunken box 2 module including fixing on surface of stone masonry wall, anchoring and making good existing disturbed surfaces in all respect complete all as specified and directed.

Supply and fix modular PVC sunken box 3 module including fixing on surface of stone masonry wall, anchoring and making good existing disturbed surfaces in all respect complete all as specified and directed.

Supply and fix modular PVC sunken box 4 module including fixing on surface of stone masonry wall, anchoring and making good existing disturbed surfaces in all respect complete all as specified and directed.

Supply and fix modular PVC sunken box 6 module including fixing on surface of stone masonry wall, anchoring and making good existing disturbed surfaces in all respect complete all as specified and directed.

Supply and fix modular metal sunken box 8 module including fixing on surface of stone masonry wall, anchoring and making good existing disturbed surfaces in all respect complete all as specified and directed.

Supply and fix modular white cover plate with frame 2 module complete all as specified and directed.

Supply and fix modular white cover plate with frame 3 module complete all as specified and directed.

Supply and fix modular white cover plate with frame 4 module complete all as specified and directed.

Supply and fix modular white cover plate with frame 6 module complete all as specified and directed.

Supply and fix modular white cover plate with frame 8 module complete all as specified and directed.

NOTE: Amount of credit of Rs. 7,81,772.00 for retrieved materials is mentioned in schedule of credit on Srl Page No. 29 of tender documents in pdf form which will be deducted offline while acceptance of tender.

Mehta Construction Co.

M/S CHANDAN BUILDERS

SHAILENDRA B TULSANI

SHREE KRISHNA INFRASTRUCTURE

Prasur Electricals & Engineering Co.

S G Enterprises

Chandan Constructions