Biennial Civil Maintenance and Housekeeping work for 1x660MW Unit of Harduaganj Thermal Power Project, Kasimpur, Aligarh

Providing and fixing white vitreous china flat back or wall corner type lipped front urinal basin of430x260x350 mm or 340x410x265 mm sizes respectively. (DSR No. 17.23)

Providing and fixing stone slab with table rubbed, edges rounded and polished, of size 75x50 cm deep and 1.8 cm thick, fixed in urinal partitions by cutting a chase of appropriate width with chase cutter and embedding the stone in the chase with epoxy grout or with cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 6 mm nominal size) as per direction of Engineer-in-charge and finished smooth. (Granite Stone of approved shade ) (DSR No. 8.10.2)

Providing and fixing 600x450 mm beveled edge mirror of superior glass (of approve with 6 mm thick hard board ground fixed to wooden cleats with C.P. brass screws and washers complete. (DSR No. 17.31)

Providing and fixing soil, waste and vent pipes:17.35.1 100 mm dia 17.35.1.1 Sand cast iron S&S pipe as per IS: 1729 17.35.2 75 mm diameter 17.35.2.1 Sand cast iron S&S pipe as per IS: 1729 (DSR No. 17.35.2.1)

Providing and fixing 100 mm sand cast Iron grating for gully trap. (DSR No. 17.29)

Providing and fixing plain bend of required degree. 17.39.1 100 mm dia 17.39.1.1 Sand cast iron S&S as per IS - 1729 (DSR No. 17.39.1.1)

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS:13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required :(610x510 mm bowl depth 200 mm ) (DSR No. 17.10.2.1)

Providing and fixing CP Brass 32mm size Bottle Trap of approved quality & make and as per the direction of Engineer-in-charge. (DSR No. 17.22A)

Providing and fixing PTMT Waste Coupling for wash basin and sink, of approved quality and colour. 17.69.1 Waste coupling 31 mm dia of 79 mm length and 62 mm breadth weighing not less than 45 gms (DSR No. 17.69.1)

Waste coupling 38 mm dia of 83 mm length and 77 mm breadth, weighing not less than 60 gms (DSR No. 17.69.2)

Providing and fixing trap of self cleansing design with screwed down or hinged grating with or without vent arm complete, including cost of cutting and making good the walls and floors: 17.60.2 100 mm inlet and 75 mm outlet 17.60.2.2 Sand Cast Iron S&S as per IS- 1729 (DSR No. 17.60.2.2)

Providing and fixing door piece, insertion rubber washer 3 mm thick, bolts & nuts complete: 100 mm 17.55.1.2 Sand cast iron S&S as per IS - 3989 (DSR No. 17.55.1)

Providing and fixing unplasticised PVC connection pipe with brass unions: 18.21.2 45 cm length18.21.2.1 15 mm nominal bore (DSR No. 18.21.2.1)

Providing and laying S&S Centrifugally Cast (Spun) / Ductile Iron Pipes conforming to IS: 8329 :18.72.2 150 mm dia Ductile Iron Class K-7 pipes (DSR No. 18.72.2)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 15 mm nominal bore (DSR No. 18.47.1)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 20 mm nominal bore (DSR No. 18.47.2)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 25 mm nominal bore (DSR No. 18.47.3)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 32 mm nominal bore (DSR No. 18.47.4)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 40 mm nominal bore (DSR No. 18.47.5)

Providing and fixing G.I. Union in existing G.I. pipe line, cutting and threading the pipe and making long screws, including excavation, refilling the earth or cutting of wall and making good the same complete wherever required. 50 mm nominal bore each 1118.30 (DSR No. 18.47.6)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 15 mm nominal outer dia Pipes (DSR No.18.8.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc.20 mm nominal outer dia Pipes(DSR No. 18.8.2 )

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply, including all CPVC plain & brass threaded fittings, i/c fixing the pipe with clamps at 1.00 m spacing. This includes jointing of pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of Engineer in Charge. Concealed work, including cutting chases and making good the walls etc. 25 mm nominal outer dia Pipes(DSR No. 18.8.3)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 15 mm nominal outer dia Pipes(DSR No. 18.9.1)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 20 mm nominal outer dia Pipes (DSR No. 18.9.2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. External work 25 mm nominal outer dia Pipes(DSR No. 18.9.3)

Providing and fixing PTMT, push cock of approved quality and colour.15 mm nominal bore, 80 mm long, weighing not less than 46 gms (DSR No. 18.57.2)

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. (110 mm diameter) (DSR No. 12.41.2)

Providing and fixing Chlorinated Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings This includes jointing of pipes & fittings with one step CPVC solvent cement, trenching, refilling & testing of joints complete as per direction of Engineer in Charge. 150 mm nominal inner dia Pipes) (DSR No. 18.9.10)

Cleaning of C.I down pipe from roof to bottom including all labour T&P complete dismantling and refixing complete (NSI)

Searching, sorting out and attending leakage and choking faults in external or internal running water mains, sever lines of different diameters at all elevations from 0 to 18 mm level including all materials as G.I bend , elbow, tee, socket, nipple etc. and supply of all labour, T&P such as thread cutting, dye, bunch voce, hacksaws pipe wrench etc. (NSI)

Rewinding of 5.00 to 7.5 H.P capacity three phase vertical or horizontal motor for pump of tubewell with class B insulated copper wire of I.S.I approved quality including painting varnishing etc. complete as per direction of E/I (NSI)

Repairing servicing of fully automatic three phase starter by replacing thermal relay including testing of load replacement of connecting wire required etc. (NSI)

Attending complaints such as replacement of taps, washers, spindle for pillar cocks etc. by providing plumper at the complaints office including all labour T&P threads, safeda etc. required for proper completion of the work. (NSI)

P/F G.I. Pipes complete with G.I. Fittings & Clamps including cutting & making good the walls etc. (Internal work) 15mm dia Nominal bore.) (DSR No. 18.10.1)

P/F G.I. Pipes complete with G.I. Fittings & Clamps including cutting & making good the walls etc. (Internal work) 20mm dia Nominal bore.) (DSR No. 18.10.2)

Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. for external work 15 mm dia nominal bore (DSR No. 18.12.1)

Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. for external work 20 mm dia nominal bore (DSR No. 18.12.2)

Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. for external work 25 mm dia nominal bore (DSR No. 18.12.3)

Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. for external work 32 mm dia nominal bore (DSR No. 18.12.4)

Providing and fixing G.I. pipe complete with G.I. fittings including trenching and refilling etc. for external work 40 mm dia nominal bore (DSR No. 18.12.5)

Providing and fixing G.I. pipes complete with G.I. fittings including trenching and refilling etc. External work 50 mm dia nominal bore (DSR No. 18.12.6)

Making connection of 25 to 40mm nominal bore G.I. distribution branch with G.I. main of following sizes by providing and fixing tee, including cutting and threading the pipe etc. complete.(DSR No. 18.13.1)

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 25 mm dia nominal bore (DSR No. 18.17.1)

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 32 mm dia nominal bore (DSR No. 18.17.2)

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 40 mm dia nominal bore (DSR No. 18.17.3)

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 50 mm dia nominal bore (DSR No. 18.17.4)

P/F gun metal gate valve with C.I. wheel of approved quality (screwed end) 65 mm dia nominal bore (DSR No. 18.17.5)

Dismantling of 100mm dia old SW Pipe line including braking of joint & bed concrete, stacking of useful material near the site within 50Mtr. lead & disposal of unserviceable material in nearest dumping place. (DSR No. 19.5.1)

P/F white vitreous china flat back wash basin size 630x450 mm including making all connection but excluding cost of fitting. (DSR No. 17.25.2)

P/F 10 liter capacity- white PVC low level flushing cistern with manually controlled device (handle lever) conforming to IS: 7231 with all fittings and fixtures complete. (DSR No. 17.18.1)

Providing and fixing 8 mm dia C.P. / S.S. Jet with flexible tube upto 1 metre long with S.S. triangular plate to Eureopean type W.C. of quality and make as approved by Engineer - in - charge. (DSR No. 17.16A)

P/F 15mm nominal ball valve (brass) of approved quality, high or low pressure, with plastic floats complete (DSR No. 18.18.1)

Providing and fixing white vitreous china pedestal type water closet (European type) with seat and lid, 10 litre low level white vitreous china flushing cistern & C.P. flush bend with fittings & C.I. brackets, 40 mm flush bend, overflow arrangement with specials of standard make and mosquito proof coupling of approved municipal design complete, including painting of fittings and brackets, cutting and making good the walls and floors wherever required : (W.C. pan with ISI marked black solid plastic seat and lid.) (DSR No. 17.3.2)

P/F P.V.C. waste pipe 32mm dia for sink or wash basin including P.V.C. waste fittings complete including west fittings complete. (DSR No. 17.28.1.1)

P/F on wall face unplasticised rigid PVC rain water pipes conforming to IS: 13592 type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion (i) single socketed pipes 110mm diameter (DSR No. 12.41.2)

P/F MS holder bat clamps of appd. Design to CI/SCI/AC rain water pipes embedded in and including cement concrete Blocks 10X10X10mm of 1:2:4 mix (1cement 2 coarse sand and 4 stone ballast) including cost of cutting holes and making good the wall complete. For 110 dia pipes. (DSR No. 17.37.1)

Providing and fixing PTMT towel rail complete with brackets fixed to wooden cleats with CP brass screws with concealed fittings arrangement of approved quality and colour. 450 mm long towel rail with total length of 495 mm, 78 mm wide and effective height of 88 mm, weighing not less than 170 gms each 555.35 (DSR No. 17.73.1)

Providing and fixing toilet paper holder : C.P. brass each 583.75 (DSR No. 17.34.1)

Providing and fixing PTMT liquid soap container 109 mm wide, 125 mm high and 112 mm distance from wall of standard shape with bracket of the same materials with snap fittings of approved quality and colour, weighing not less than 105 gms. (DSR No. 17.71)

P/F PTMT pillar cock of approved quality & colour.15mm nominal bore, 86 mm long, weighing not less than 88gms. (DSR No. 18.54.1)

P/F PTMT pillar cock of approved quality & colour.15mm nominal bore, 107mm long, weighing not less than 110gms. (DSR No. 18.56.1)

Cleaning of Septic Tank chambers & disposal of malwa outside the boundary wall of colony/ power house. (NSR)

Cleaning of Inspection Chamber & disposal of malwa outside the boundary wall of colony/ power house. (NSR)

P/F 30 cm. length/ 15mm nominal size uplasticised PVC connection pipe with brass unions (DSR No. 18.21.1.1)

0mm sand cast iron grating for gully trap. (DSR No. 17.29)

P/F PTMT stop cock of approved quality & colour 15mm nominal bore, 86mm long weighing not less than 88gms. (DSR No. 18.55.1)

-do- but CI bib cock. (DSR No. 18.54.1)

P/F brass bib cock 15mm nominal size of approved quality. (DSR No 18.15.1)

-do- but stop cock (DSR No. 18.16.1)

P/F 15mm nominal bore C.P. Brass bib cock of approved quality conforming to IS:8931 (DSR No. 18.49.1)

P/F C.P. brass stop cock ( concealed) of standard design and approved of 15mm nominal bore (DSR No. 18.52.1)

P/F battery for sensor of automatic pillar cock(NSR)

P/L in position cement concrete 1:4:8 ( 1 cement : 4 coarse sand 8 graded stone aggregate 40mm nominal size) excluding the cost of centering and shuttering- all work up to plinth level. (DSR No. 4.1.8)

R.C.C. work in beams, suspended floors, roofs having bands, plain window sills, staircase and spiral stair cases up to floor five level excluding the cost of centering, shuttering, finishing and reinforcement with 1:2:4 ( 1 cement : 2 coarse sand : 4 graded stone aggregate 20mm nominal size) (DSR No. 5.3)

12mm thick cement plaster of mix 1:6 (1cement : 6 coarse sand ) (DSR No. 13.4.2)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering-all work up to plinth level 1:2:4 ( 1 cement 2 coarse sand 4 graded stone aggregate 20mm nominal size) (DSR No. 4.1.3)

40mm thick with 20 mm nominal size stone aggregate cement concrete flooring in 1:2:4 (1cement: 2 Coarse Chambal red Sand : 4 graded stone aggregate ) finished with floating coat of neat cement including cement slurry, but excluding the cost of nosing of steps etc. complete.(DSR No. 11.3.1)

Centering and shuttering including strutting, propping etc. and removal of form for foundations, footings, bases of columns etc. for mass concrete. (DSR No. 5.9.1)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in foundation and plinth in: Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR No. 6.1.2)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in : Cement mortar 1:6 (1 cement : 6 coarse sand) (DSR No. 6.4.2)

Cleaning of old bricks recovered from demolition of old brickwork by removing mortar, lumps and any other loose material from bricks and making good for use in masonry. (NSI)

Brick work with common burnt clay F.P.S. (non modular) bricks of class designation 7.5 in superstructure above plinth level up to floor V level in all shapes and sizes in :Cement mortar 1:6 (1 cement : 6 coarse sand) ( Old brick provided by department) (NSR)

Demolishing brick work in cement mortar including stacking of serviceable material and disposal of unserviceable material within 50 Mtr. Lead (DSR No. 15.7.4)

Dismantling of old plaster skirting racking out joint and cleaning the surface for plaster incl. disposal of rubbish to the dumping ground within 50 mtrs lead. (DSR No. 15.56)

Demolishing RCC work manually/ by mechanical means including stacking of steel bars and disposal of unserviceable material within 50 mit lead as per direction of engineer-in-charge (DSR No. 15.3)

Carriage of earth and rubbish and concrete waste by mechanical transport including loading, unloading and stacking upto lead 3 km (DSR No. 1.1.2)

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent(DSR No. 11.56.1)

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick (DSR No. 11.26.1)

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete. (DSR No. 11.27)

P/F 1st quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by E/I, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement:3 coarse sand) and jointing with grey cement slurry @3.3 kg per sqm, incl. pointing in white cement mixed with pigment of matching shade complete. (DSR No 11.36)

P/F ceramic glazed floor tiles of size 300X300 mm (thickness to be specified by manufacturer) of 1st quality conforming to IS: 15622, of approved make in colours such as white, ivory, grey, fume red brown, laid on 20 mm thick cement mortar 1:4 (1 cement: 4 coarse sand) incl. pointing the joints with white cement and matching pigment etc. complete. (DSR No. 11.37)

Providing and laying vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption's less than 0.08% and conforming to IS : 15622 of approved make in all colours and shades, laid on 20mm thick cement mortar 1:4 (1 cement : 4 coarse sand) including grouting the joints with white cement and matching pigments etc., complete of size of tile 600X600 mm (DSR No. 11.41.2)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. (DSR No. 10.1)

Structural steel work in single section, fixed with or without connecting plate, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete. Steel provided by department (NSR)

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer all complete.(DSR No. 10.2)

Providing and applying fibre reinforced elastomeric liquid water proofing membrane with resilient acrylic polymers having Sun Reflectivity Index (SRI) of 105 on top of concrete roof in three coats @10.76 litre/ 10 sqm. One coat of self-priming of elastomeric waterproofing liquid (dilution with water in the ratio of 3:1) and two coats of undiluted elastomeric waterproofing liquid (dry film thickness of complete application/system not less than 500 microns). The operation shall be carried out after scrapping and properly cleaning the surface to remove loose partic

les with wire brushes, complete in all respect as per the direction of Engineer-in-Charge. (DSR No. 22.22A)

22.5 Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.) (DSR No. 22.5)

Providing and laying GP 2 grouting (NSI)

Epoxy Resin –C/257 (NSI)

Making 25 mm. dia bore of 200 mm depth with hydraulic hammer and grouting 20 mm bolt with chemical HIT RE500 of hilti brand (bolts shall be provided by UPRVUNL) (NSI)

For sealing cracks and faulty construction joints, routed out/making U-shape groove size 25x25mm and then primed the area with integral crystalline slurry @0.05kg/ running metre and while the surface is tacky filled the groove upto surface with crystalline mortar @1.50kg/ running metre. Once crystalline mortar is touch dry then finally applied two coats of integral crystalline slurry @0.05kg/running metre per coa.(22.25.1 )

Providing and inserting 12mm dia galvanised steel injection nipple in honey comb area and along crack line including drilling of holes of required diametre (20mm to 30mm) up to depth from 30mm to 80mm at required spacing and making the hole & crack dust free by blowing. compressed air, sealing the distance between injection nipple with adhesive chemical of approved make and allow it to cure complete as per direction of Engineer-In-Charge

Making 30 mm. dia bore of 200 mm depth with hydraulic hammer and grouting 24 mm bolt with chemical HIT RE500 of hilti brand (bolts shall be provided by UPRVUNL) (NSI)

P/F ISI marked 30 mm thick door shutters conforming to IS: 2202 non-decorative type including ISI marked stainless steel butt hinges with necessary screws, core of block board construction with frame of 1st class hard wood and well matched commercial 3 ply veneering with vertical grains or cross bands (DSR No. 9.21.2)

Renewing glass panes, with putty and nails, wherever necessary incl. racking out old putty. Float glass panes of thickness 4.0 mm (DSR No. 14.5.1)

Re-fixing old glass panes with putty and nails (DSR No 14.10)

Providing and fixing 12 mm thick frameless toughened glass door shutter of approved brand and manufacture, including providing and fixing top & bottom pivot & double action hydraulic floor spring type fixing arrangement and making necessary holes etc. for fixing required door fittings, all complete as per direction of Engineer-in charge (Door handle, lock and stopper etc.to be paid separately).(DSR No 21.18)

Welding by gas or electric plant including transportation of plant at site etc. complete.(DSR No. 10.22)

per cm length

Fixing of door chaukhat in existing opening including embedding chaukhats in floor or walls or cutting masonry for hold fast in C.C. block with cement concrete In 1:3:6 (1 cement, 3 coarse sand, 6 graded stone Aggregate 20mm nominal size), painting 2 coats of coal tar 2 sides of chaukhat & making good the damages in walls or floor as required complete. (DSR No. 14.2.1)

Same as above but window chaukhat (DSR No.14.2.2)

P/F hard drawn steel wire fabric 75x25mm mesh of weight not 7.75 Kg. per Sqm to window frames etc including 62x19 mm beading of IInd class Teak wood. (DSR No. 9.50)

P/F IS3564 marked aluminum die cast body tubular type universal hydraulic door closer with necessary accessories and screws etc. complete. (DSR No. 9.83)

P/F fly proof galvanized M.S. wire gauge to windows and clerestory windiws using wire gauge with average width of aperture 1.4mm in both direction with wire of dia .63mm all complete. With 12mm M.S.U beading. (DSR No. 9.51.2)

P/F ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 300x16 mm (DSR No. 9.62.1)

P/F ISI marked oxidized M.S. sliding door bolts with nuts and screws etc. complete : 250x16 mm (DSR No. 9.62.2)

Providing and fixing bright finished brass hanging type floor door stopper with necessary screws, etc. complete. (DSR No. 9.82)

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 250x10 mm (DSR No. 9.63.1)

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 200x10 mm (DSR No. 9.63.2)

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 150x10 mm (DSR No. 9.63.3)

Providing and fixing ISI marked oxidized M.S. tower bolt black finish, (Barrel type) with necessary screws etc. complete : 100x10 mm (DSR No. 9.63.4)

P/F ISI marked oxidized M.S. handles conforming to IS:4992 with necessary screws etc. complete : 125 mm (DSR No. 9.66.1)

P/F ISI marked oxidized M.S. handles conforming to IS:4992 with necessary screws etc. complete : 100 mm (DSR No. 9.66.2)

P/F ISI marked oxidized M.S. handles conforming to IS:4992 with necessary screws etc. complete : 75 mm (DSR No. 9.66.3)

Providing and fixing 1 mm thick M.S. sheet door with frame of 40x40x6mm angle iron and 3mm M.S. gusset plates at the junctions and corners, all necessary fittings complete, including applying a priming coat of approved steel primer. Using M.S. angels 40x40x6 mm for diagonal braces. (DSR No. 10.5.1)

Providing and fixing aluminum work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS : 1285, fixed with rawl plugs and screws or with fixing clips, or with expansion hold fasteners including necessary filling up of gaps at junctions, at top, bottom and sides with required PVC/neoprene felt etc. aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing and paneling to be paid for separately) : For fixed portion Anodized aluminium (anodized transparent or dyed to required shade according to IS:1868, Minimum anodic coating of grade

AC 15) (DSR No. 21.1.1.1)

P/F double action hydraulic floor spring of approved brand and manufacture conforming to IS: 6315 having brand logo embossed on the body/plate with double spring mechanism and door weight upto 125 kg, for doors, including cost of cutting floors , embedding in floors as required and making good the same matching to the existing floor finishing and cover plates with brass pivot and single piece MS sheet outer box with slide plate etc. complete as per direction of E/I With stainless steel cover plate minimum 1.25 mm thickness (DSR No. 21.4.1)

Filling the gap in between aluminium frame and adjacent RCC/Brick/Stone work by providing weather silicon sealant over backer rod of approved quality as per architectural drawings and direction of E/I complete upto 5 mm depth and 5 mm width (DSR No. 21.8.1)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm) (DSR No.21.3.1)

Providing and fixing Brass 100mm mortice latch and lock with 6 levers without pair of handles (best make of approved quality) for aluminium doors including necessary cutting and making good etc. complete. (DSR No. 21.13)

Providing carpenter IInd class. (DSR No. 112)

Man day

P/F 30 mm with ISI marked stainless steel butt hinges with necessary screws, flush door shutters conforming to IS: 2202 (Part-I) decorative type core of block board construction with frame of 1st class hard wood and well matched teak 3 ply veneering with vertical grains or cross bands and face veneers on both faces of shutters.(DSR No. 9.20.2)

Repairing & Fixing Pre-Painted Coil coated steel false ceiling system, tile type square pattern panels 600x600 m.m. size at all level, for all kind of work, consisting of 0.5 mm tick galvanized to grade 180 as per IS:277, along with galvanized. Supporting Steel member exposed faces of galvanized Member to be Supporting with regular modified polyester coating/super polyester coating minimum 20 DFT to form panels of specified size for tile type panels and toll formed stove enameled 0.6 mm thick steel carrier, for Fixing of lineal type panels by clip on arrangement, suspended form RCC slab/structural steel or catwalk way steel channel grid above with 4 mm (minimum) galvanized wires (rods), with special height adjustment clips, providing angle section of minimum 25 mm leg with along the perimeter of ceiling, including all labor, material, supporting grid system (members minimum 0.8mm thick and galvanized @ 150g/sq.M.as per IS:277) equipment, handling, transportation, workmanship, anchor fasteners for making suspension arrangement from RCC. Including all labour, material T&P etc. Complete but excluding cost of false ceiling.

Providing and fixing powder coated aluminium work (minimum thickness of powder coating 50 micron) consisting of tee/ angle sections, of approved make conforming to IS : 733 in frames of false ceiling including aluminium angle cleats with necessary C.P. brass/ stainless steel sunk screws, aluminium perimeter angles fixed to wall with stainless steel rawl plugs @ 450 mm centre to centre and fixing the frame work to G.I. level adjusting hangers 6 mm dia. with necessary cadmium plated machine screws all complete as per approved architectural drawings and direction of the Engineer-incharge (level adjusting hangers, ceiling cleats and expansion hold fasteners to be paid for separately)(DSR No. 21.5)

Attending complaint regarding aluminium work of door/window/partition including all labour, material T&P, Fitter and helper (NSR)

P/F 15 mm thick tegular edged light weight calcium silicate false ceiling tiles. false ceiling tiles of Size 595x595mm of approved texture, design and patterns having NRC (Noise Reduction coefficient) of 0.50 (minimum) as per IS 8225:1987, Light reflectance of 85% (minimum). Non combustible as per BS:476 (part-4), fire performance as per BS:476 (part 6 &7), humidity resistance of 100%, thermal conductivity < 0.043 W/m K as per ASTM 518:1991 (NSR based on 26.22.1)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 mm dia. R.C.C. pipe (DSR No. 19.6.2)

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 900 mm dia. R.C.C. pipe (DSR No. 19.6.10)

Pumping out water caused by springs, tidal or river seepage, broken water mains or drains and the like.

Kilo Litre

Providing and applying white cement based putty of 1mm thickness over plastered wall surface to prepare the surface even and smooth complete (DSR No. 13.8)

Wall painting with plastic emulsion paint of approved brand and manufacture to give an even shade : One or more coats on old work (DSR No. 13.98.1)

Finishing with Deluxe Multi surface paint system for interiors and exteriors using Primer as per manufacturers specifications : Painting Steel work with Deluxe Multi Surface Paint to give an even shade. Two or more coat applied @ 0.90 ltr/ 10 sqm over an under coat of primer applied @ 0.80 ltr/ 10 sqm of approved brand and manufacture (DSR No. 13.48.3)

Painting wood work with Deluxe Multi Surface Paint of required shade. Two or more coat applied @ 0.90 ltr/10 sqm over an under coat of primer applied @0.75 ltr/ 10 sqm of approved brand or manufacture (DSR No. 13.48.2)

Removing dry or oil bound distemper, water proofing cement paint and the like by scrapping, sand papering and preparing the surface smooth including necessary repairs to scratches etc. complete. (DSR No. 13.91)

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete. (DSR No. 13.80)

Distempering with oil bound washable distemper of approved brand and manufacture to give an even shade :Old work (one or more coats) . (DSR No. 13.90.1)

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm) (DSR No. 13.44.1)

Distempering with 1st quality acrylic distemper (ready mixed) having VOC content less than 50 gms/litre, of approved manufacturer, of required shade and colour complete, as per manufacturer’s specification. Two or more coats on new work (DSR No. 13.42.1)

Distempering with 1st quality acrylic distemper (ready made) having VOC content less than 50 gm per ltr. of approved manufacturer and of required shade and colour complete. as per manufacturer’s specification One or more coats on old work (DSR No. 13.108)

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shadeOne or more coats on old work (DSR No. 13.101.1)

Painting with acid proof paint of approved brand and manufacture of required colour to give an even shade( Two or more coats on new work) (DSR No. 13.64.1)

Finishing walls with water proofin

g cement paint of required shade.Old work (one or more coats applied @ 2.20 kg/10 sqm) over priming coat of primer applied @ 0.80 litrs/10 sqm complete including cost of Priming coat. (DSR No. 13.109.1)

Painting on G.S. sheet with synthetic enamel paint of approved brand and manufacture of required colour to give an even shade : New work (two or more coats) including a coat of approved steel primer but excluding a coat of mordant solution. (DSR No. 13.53.1)

White washing with lime to give an even shade: New work (three or more coats) (DSR No. 13.37.1)

Painting with synthetic enamel paint of approved brand and manufacture to give an even shade :Two or more coats on new work(DSR No. 13.61.1)

Colour washing such as green, blue or buff to give an even shade : New work (two or more coats) with a base coat of white washing with lime (DSR No. 13.39.1)

Lettering with black Japan or approved paint of approved band and manufacture. (DSR No. 13.71)

per ltr per cm. height

Clearing jungle including uprooting of rank vegetation, grass brush wood, trees and sapling of girth up to 30cm measured at a height of 1 mtr. above ground level and removal of rubbish up to a distance of 50mtr outside the periphery of the area cleared. (DSR No. 2.31)(Past tender Rate)

Cleaning grass and removal of the rubbish up to a distance of 50M outside the periphery of the area cleared .(DSR No. 2.32)(Past tender Rate)

Surface dressing of the ground including removing vegetationand inequalities not exceeds15cm deep and disposalof rubbish lead up to 50m and lift up to1.5m all kind of soil (DSR No 2.28.1)(Past tender Rate)

Felling trees of girth measured at a height of 1 M. above ground level including cutting of trunks and branches and stacking serviceable material and disposal of unserviceable material beyond 30 Cm. girth . (DSR No. 2.33.1)(Past tender Rate)

Cleaning of roof of building of various height from 4 to 36 M including removing of grass, industrial waste , garbage such as Ash . Coal dust, building waste etc. maximum thickness 10 cm including sweeping and lifting and cartage of the same from roof to hopper by manual labour and dropping the same up By hopper including all labour, T&P etc. (Past tender Rate)

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc daily at all floors of Admin building(G+2) including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge.

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc daily at all floors of Service building(G+3) including all manpower, T&P etc for proper completion of work as per direction of Engineeer-in-charge.

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. ER2,S & T Building,CISF cabin 1 &2 near Material gate.

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. Intake Pump House,Raw Water Pump House,Chemical house near cooling tower

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. AHP Control Building,AWRS Chemical house

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. DM plant,Ammonia Shelter,Chemical building,ERS building

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. TG Building 0m,12 m,18m

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. Switch Yard Control Building,CWPH,CWST,Auxillary boiler building

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. FGD Control Building,ESP Control building,FOPH,SCR Building

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc etc. at all floors of following building sets including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge. Time office Building,Fire station

Sweeping, cleaning ,mopping & dusting ,cleaning of spider net, glass panes of doors and windows, wet wash with phenyle or approved germicide daily and cleaning of toilet floor & toilet seats,washbasins,urinals etc. 24x7 at CCR +18M building including all manpower, T&P etc for proper completion of work as per direction of engineer-in-charge.

Sweeping&cleaning of roads and side patteries including removal of vegetation. Sweeping of painted bitumen surface brick on edge of road upto side drain For double lane road (NSR)(Past tender Rate)

Sweeping&cleaning of roads and side patteries including removal of vegetation. Sweeping of painted bitumen surface brick on edge of road upto side drain For single lane road (NSR)(Past tender Rate)

Cleaning, removal and stacking of deposited material from Trench culvert and siphon such as ash earth debris garbage industrial waste and grass etc. including lift upto 1.5M and lead upto 50M by head load including cleaning of both side patris of drain 1.00 M both side of drain and also including making by pass arrangement to avoid flooding disposal of sludge (measurement shall be done of stacked garbage and 8% deduction shall be made against bulkage including all labour T&P etc.

Cleaning of sludg

e ash dirt of any other deposited material from main drain as per direction of E/I including cleaning of culverts on drains both side parties of drain 1.0 Mt. wide on each side cleaning shall be done by making bundah on both sides i.e. upstream as well as down stream and taking out complete sludge and its disposal upto a distance of 1 km. beyond the boundry/premessis of power house/colony disposal of sludge to be done within 07 days of the cleaning All arrangements to avoid flooding & dewatering may be done as required for proper completion of the work. Section wise Quantities are given below: 0.04 to 0.25 Sq. M section

Cleaning of sludge ash dirt of any other deposited material from main drain as per direction of E/I including cleaning of culverts on drains both side parties of drain 1.0 Mt. wide on each side cleaning shall be done by making bundah on both sides i.e. upstream as well as down stream and taking out complete sludge and its disposal upto a distance of 1 km. beyond the boundry/premessis of power house/colony disposal of sludge to be done within 07 days of the cleaning All arrangements to avoid flooding & dewatering may be done as required for proper completion of the work. Section wise Quantities are given below:0.25 to 0.5 sqm section

Cleaning of sludge ash dirt of any other deposited material from main drain as per direction of E/I including cleaning of culverts on drains both side parties of drain 1.0 Mt. wide on each side cleaning shall be done by making bundah on both sides i.e. upstream as well as down stream and taking out complete sludge and its disposal upto a distance of 1 km. beyond the boundry/premessis of power house/colony disposal of sludge to be done within 07 days of the cleaning All arrangements to avoid flooding & dewatering may be done as required for proper completion of the work. Section wise Quantities are given below: 0.65 to 0.95 sqm section

Disposal of industrial garbge such as malwa, Ash, grass etc from road side dust bin, road and stacked malwa / Ash etc which has already removed form roofs and drains and Its disposal up to 2 Km. out side the power house including cost of all labour T&P etc. required for proper completion of work. (20% voids shall be made for Net Qty.) ash,lime, building rubbish.

Removal of dead animals from Power house area to outside the power house including all labour & T&P complete within same day as per direction of E/I (NSR)

Hiring of J.C.B./Hydra with driver & fuel for different type of Job as per direction of Engineer Encharge. (NSR)

Supply of tractor with trolley including driver, fuel and sufficient labour for loading and unloading scrap material in Power house area (various site to scrap yard) etc. complete as direction of E/I.

Supplying and laying the lime along with Road Side and main gate with help of Rope including all T&P etc. complete. N.S.R.

Maintenance of lawn grass/flower beds/permanent beds including cutting of grass with lawn movers (grass cutter), leveling with lawn roller, watering and removing weeds etc, and cutting of hedge in proper shape & height and also trimming of branches of trees, including daily sweeping and cleaning of entire park area clearing jungle and spreading of dump manure fertilizer, pesticides, disposal of malwa/garbage generated due to execution of these work up to nearest dustbin as per instruction of E/I. Rates includes all T&P required for proper completion of work. (area of all parks are almost equal)(Past tender Rate) Admin Building park

Maintenance of lawn grass/flower beds/permanent beds including cutting of grass with lawn movers (grass cutter), leveling with lawn roller, watering and removing weeds etc, and cutting of hedge in proper shape & height and also trimming of branches of trees, including daily sweeping and cleaning of entire park area clearing jungle and spreading of dump manure fertilizer, pesticides, disposal of malwa/garbage generated due to execution of these work up to nearest dustbin as per instruction of E/I. Rates includes all T&P required for proper completion of work. (area of all parks are almost equal)(Past tender Rate) Switchyard east and south side Park

Maintenance of lawn grass/flower beds/permanent beds including cutting of grass with lawn movers (grass cutter), leveling with lawn roller, watering and removing weeds etc, and cutting of hedge in proper shape & height and also trimming of branches of trees, including daily sweeping and cleaning of entire park area clearing jungle and spreading of dump manure fertilizer, pesticides, disposal of malwa/garbage generated due to execution of these work up to nearest dustbin as per instruction of E/I. Rates includes all T&P required for proper completion of work. (area of all parks are almost equal)(Past tender Rate) Material gate and divider area Park

Spreading of dump manure.

Supply & Sprinkling of herbicide Glyphosale (41.1) along with herbicide urea as Supplement in herbs, grass, jungle area including all material, Labour, T&P etc. for proper completion of work.

Providing tractor with fuel with trolley with driver & 2no Labour for loading & unloading including carriage of garbage, grass building rubbish etc. For dumping at dumping yard outside/inside the Plant area.

Supply and lying of various manures /Pesticides. Urea

Supply and lying of various manures /Pesticides. DAP

Supply and lying of various manures /Pesticides. Rose Mixture

Supply and lying of various manures /Pesticides. Neem Khali

Supply and lying of various manures /Pesticides. Bone Dust

Supply and lying of various manures /Pesticides. Rogar

Supplying plastic pots. 18”

Supplying plastic pots. 24”

Supplying concrete pots. 18”

Supplying concrete pots. 24”

Supplying Croton plants not less than 3 feet hight

Supplying Erocaria plants not less than 3 feet hight

Supplying Palm Tree plants not less than 3 feet hight

Supplying of Guldawdi/Double Dahelia in eathen Gamala 6”

Supplying/sowing seasonal flower plants saplings in flower beds.

Supply and sprinkling of herbecide glyphosale (41%) alongwith herbecide urea as suppliment in herbs grass, jungle area in B&C power house area including all material, labour, T&P etc. for proper completetion of work.

Per Month

c periodically.

Disposal of moorum/building rubbish/ malba/ similar unserviceable, dismantled or waste material by mechanical transport including loading, transporting, unloading to approved municipal dumping ground for lead upto 10 km for all lifts, complete as per directions of Engineer-in-charge

periodic Cleaning of all tank including disposal of waste out side the plant area as per direction of E/I including cost of all labour T&P etc. required for proper completion of the work.

Pumping out sewage from manholes/ sewer line/ surface drain including cost of all materials. Labour & T&P etc. required for proper completion of work by deploying 5HP diesel pump.