8502 REPAIR AND MAINT TO FITTING AND FIXTURES DBs ELECTRICAL PROTECTIVE SYSTEM ELECTRICAL WIRING SUBMAIN LIGHT FITTINGS EARTHINGS CEILING FAN GEYSER AND OTHER MISCELLANEOUS WORK IN AREA OF CARIAPPA ENCL STAVELY ROAD EME UNDER GE SOUTH PUNE

Amount

Labour only for repair / maintenance of internal light fitting of any type and attending complaints of No light/ceiling fan/ exhaust fan/ geysers/ security light/ ceiling and wall light /Cable fault of any size & type / earth leakage/ short circuit / neutral break mains / substations / internal circuits of existing system of main building / block, making continious electric supply including carrying out minor repairs etc as required to make the system functional including replacing fuse wire, copper thimbles, glands,etc complete all as specified and all as directed by Engr-in-charge. Note: (i) Attending of 01 No. complaints / defects and make it functional shall be measured as one job. (ii) Cost of spares like Driver, lamp holder, connection wire, capacitor etc. replaced against above mentioned item will be measured & paid for separately under respective items of BOQ. (iii) The contractor's representative will report to concerned JE E/M at 0900hrs daily to collect the list of defects / complaints and will be submited the completion report on following day before 0900hrs to the JE E/M. (iv) The contractor has to rectify the defects / complaints and make the light fittings functional within 24 hours from the time the list of defective lights is handed over to him / his rep by the concerned JE E/M. In case the light fitting is not made functional for whatsoever reason within the specified time limit, an amount of Rs 100/- per such defective light fitting per day will be recovered from the amount due to him through RAR / Final Bill. (v) The contractor shall maintain proper record of repair / maint in a binded register duly bringing out the details of spares replaced on each and every light fitting and get it authenticated from concerned JE E/M on daily basis. The contractor shall put up the maint record register to Engineer-in-charge for inspection every Monday or as and when asked for. (vi) The contractor shall maintain sufficient stock of spares / material required for repair / maint of light fittings with the concerned JE E/M.

Supply only Modular Switch piano flush type, single pole, one way, and 10 Amp single module complete all as specified and directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only Modular Switch piano flush type, single pole, one way, and 20 Amp single module complete all as specified and directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only Modular Switch piano flush type, single pole, two way, and 10 Amp single module complete all as specified and directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only Modular Socket outlet multipurpose having provision for 3 pin, 6 Amp and 2 pin, 6 Amp, 2 module piano flush type complete all as specified and directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only Modular Switch Socket outlet multipurpose having provision for 3 pin, 16 Amp and 2 pin,6 Amp, 2 module piano flush type complete all as specified and directed. Make - Anchor Roma/Anchor Rider/Vinay Adora

Supply only modular step type fan regulator 120 watt 2 module suitable for 230 volt 50 Hz AC supply complete all as specified and as directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only Bell push modular 10 Amps, one module complete all as specified and directed. (Make - Anchor Roma/Anchor Rider/Vinay Adora)

Supply only switch socket combination with box 5/6 Amps flush mounted 5 pin multi purpose complete all as specified and directed.

Supply only switch socket combination with box 5/15 Amps flush mounted 3/5 pin multi purpose complete all as specified and directed.

S&F lamp holder insulated body with back plate PVC/Polycarbonate type with cord grip cap, angular type fixed on wall complete all as specified and directed. (Make Anchor/Havells /VINAY)

S&F Ceiling rose, surface Bakelite suitable ISI marked complete all as specified and directed. (Make :- Anchor / Havells /VINAY )

S&F Bell Electric Ding dong type suitable for operation on 230 volt 50 HZ A C supply complete all as specified and as directed

Taking down carefully exising unserviceable point wiring of any type (light, fan, socket or power), complete (fitting such as switches,ceiling rose, pendent, regulators etc) for taking credit and making good disturbed surfaces of wall, floor etc. complete all as specified and as directed.

M & L for Point wiring using approved colour coding as per IS, with multistranded copper conductor 1.5 Sq. mm (nominal area), single core, PVC insulated and unsheathed FRLS cable 1100 volts grade, ISI-694 marked drawn through in and including heavy duty, PVC casing caping including all accessories etc, heavy duty ISI marked, concealed / surface mounted as per site requirement with mild steel sunken boxes / PVC surface mounted box with earth dolly duly, covered with laminated hylem sheet/ PVC cover , ISI marked suitable for fixing of switches, fan regulators and sockets including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly complete all as specified and directed for the following :- (a). One light point controlled by one, one way switch 5 Amps

As per item no. 15 above but One fan point/ exhaust fan point controlled by one, one way switch 5 Amps

All as per item no. 15 above but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad, complete all as specified and directed.

All as per item no. 15 above but One bell point controlled by bell switch 5 Amps, complete all as specified and directed.

All as per item no. 15 above but One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board, complete all as specified and directed.

All as per item no. 15 above but using 2.5 sq mm single core copper conductor cable for 5/15 amps point including 2.5 sq mm copper conductor as earth continuity conductor, complete all as specified and directed.

M & L for Point wiring with colour coding as per IS, with multistranded copper conductor 1.5 Sq.mm nominal cross sectional area, single core, 1100 Volts grade, multi stranded, FRLS- Cable conforming to IS: 694-1990 PVC insulated, unsheathed copper conductor cable drawn through in and including heavy duty PVC concealed conduit of white/ ivory colour including all accessories after cutting chasing in wall of any type /ceiling etc, including making good of disturbed surface and finish with two coats of white / colour washing / distempering etc to match the existing surface complete etc heavy duty ISI marked, with GI sunken boxes with earth dolly duly, covered with modular white cover plate with frame suitable for modular switches including PVC insulated multistranded copper conductor 1.5 Sqmm (nominal area) single core FRLS cable as earth continuity conductor to common earth and connecting to earth dolly etc complete all as specified and directed for the following :- (a). One light point controlled by one, one way switch 5 Amps

All as per item no. 21 above but One fan point/ exhaust fan point controlled by one, one way switch 5 Amps, complete all as specified and directed

All as per item no. 21 above but One light point controlled by TWO WAY switches 5 Amps , complete all as specified and directed

All as per item no. 21 above but One 3 pin 5 Amps switch socket outlet point controlled by one switch on independent boad, complete all as specified and directed

All as per item no. 21 above but One bell point controlled by bell switch 5 Amps, complete all as specified and directed

All as per item no. 21 above but One 3 point 5 Amps switch socket outlet point controlled by one switch on the same board, complete all as specified and directed

Ditto all as per item no. 21 above but using 2.5 sq mm single core copper conductor cable for 5/15 amps point including 2.5 sq mm copper conductor as earth continuity conductor, complete all as specified and directed

M & L for Sub main wiring with approved colour coding as per IS with four single core PVC insulated FRLS cable with stranded copper conductor of size with 10 Sqmm , 1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS- confirming to IS: 694-1990 with and including continuous earth wire of size 1x10 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable drawing into and including rigid non metallic PVC non metallic rigid heavy duty PVC conduit of white/ ivory colour and its accessaries ISI marked of suitable size concealed in wall etc and connected to common earth dolly including all cutting / chases etc in any type of wall , making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. Note:-One meter of conduit along with 4x10 sq mm wire and 1x10 sq mm earth shall be measured as one unit length.

Ditto as per item no 28 above but 4 x 6 sq mm with one continuous earth wire of size 6.0 sq mm, complete all as specified and directed. (Note :- One meter of conduit along with 4x6 sq mm wire and 1x 6 sq mm earth shall be measured as one unit length.)

Ditto as per item no 28 above but 2 x 6 sq mm with one continuous earth wire of size 6.0 sq mm, complete all as specified and directed. (Note:-One meter of conduit along with 2x6 sq mm wire and one 6 sq mm earth shall be measured as one unit length.)

Ditto as per item no 28 above but 2 x 4 sq mm with one continuous earth wire of size 4.0 sq mm, complete all as specified and directed. (Note:-One meter of conduit along with 2x4 sq mm wire and one 4 sq mm earth shall be measured as one unit length.

M & L for Sub main wiring with approved colour coding as per IS with two single core PVC insulated FRLS cable with stranded copper conductor of size with 04 Sqmm nominal cross sectional area,1100 Volts grade, stranded, PVC insulated, unsheathed, copper conductor FRLS- confirming to IS: 694-1990 with and including continuous earth wire of size 4 Sqmm nominal cross sectional area, single core, PVC insulated, copper conductor cable and including ISI marked PVC casing caping including fitting in wall etc and connected to common earth dolly making good to walls etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified & directed. (Note :- One meter of PVC casing caping along with 2x4 sq mm wire and one 4 sq mm earth shall be measured as one unit length)

Ditto as per item no 32 above but 2 x 6 sq mm with one continuous earth wire of size 6.0 sq mm, complete all as specified and directed. Note:-One meter of PVC casing caping along with 2x6 sq mm wire and one 6 sq mm earth shall be measured as one unit length.

Ditto as per item no 32 above but 4 x 6 sq mm with two continuous earth wire of size 6.0 sq mm, complete all as specified and directed. (Note:-One meter of PVC casing caping along with 4x6 sq mm wire and 2x 6 sq mm earth shall be measured as one unit length.)

Ditto as per item no 32 above but 4 x 10 sq mm with two continuous earth wire of size 6.0 sq mm, complete all as specified and directed. (Note:-One meter of PVC casing caping along with 4x10 sq mm wire and 2x 6 sq mm earth shall be measured as one unit length.)

Taking down carefully sub main wiring of any type and size and making good disturbed surfaces , complete all as specified and directed.

S&F in replacement of GI pipe bracket of 25 mm dia 1 mtr long bend to shape for street light fitting made out of 25 mm dia GI light grade pipe fixed on pole/wall using suitable clamp including necessary new nut, bolt and washer complete all as specified and directed.

S&F in replacement LED building security light fiitting 30 W, IP-65 protection made up of die cast alluminium housing with high power LED as lighting source and lens embeded PC cover having TOP opening seperate driver compartment complete all as specified and directed by Engr-in-charge. Make- Philips/Bajaj/ Havells/Wipro

Supply only Retrofit 4 pin 18/20 watt 6500K LED PL-L with direct plug and play suited for installation in existing 2G11 lamp holders, complete all as specified and directed Make- Philips/Bajaj/ Havells/Wipro

S&F in repalcement recess mounted 2' x 2' LED Panel lights 40 W LED 5700K, 240Volts and glare free symmetrical illumination suitable for Armstrong/Grid ceiling, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully all as specified and directed. Make:- Make- Philips/Bajaj/ Havells/Wipro Note: The quoted price shall include the cost of Light and its driver.

S&F in replacement of 18/20 watt, 230V surface and wall mounted LED batten, extruded aluminium housing with polycarbonate diffuser and integrated electronic driver including connecting up with twin core twisted flexible copper condctor cable from ceiling rose, complete all as specified and directed Make- Make- Philips/Bajaj/ Havells/Wipro

S&F in replacement 1x10 watt, 230V surface and wall mounted LED batten suitable for mirror light with polycarbonate housing and integrated electronic electronic driver including connecting up with twin core twisted flexible copper conductor cable from ceiling rose, complete all as specified and directed Make- Make- Philips/Bajaj/ Havells/Wipro

Supply & fix LED recess mounting downlighter with ceiling cut out of 125 mm dia of wattage 9 watt 6500K with LED backlit round downlighter made of PDC AL with high efficient LEDs & glare free opal diffuser, IP20 including taking down existing, complete all as specified and directed Make- Make- Philips/Bajaj/ Havells/Wipro

Supply & fix in replacement LED fixture 30 watt surface mounted ceiling light 6500K with diffuser to give glare free light of size 300x300x35 mm, aluminium housing with compatible driver complete all as specified & directed. Make- Philips/Bajaj/ Havells/Wipro

S&F in replacement recess type LED ceiling lights 15 W LED with ceiling cut out of Ø 170 mm, 6000K recess mounted downlighter with separate replaceable electronic driver including connecting with twin core wire, including cutting the existing false ceiling dia to the required size and also matching to the adjacent false ceiling surfaces carefully complete all as specified and directed. Make- Philips/Bajaj/ Havells/Wipro

S&F in replacement recess mounted 2' x 2' LED Clean room lights 36-42 W LED 5700K, 240Volts and glare free symmetrical illumination, Environmental friendly, new generation, energy saving, high power LED as a light source with clear diffuser and separate replaceable electronic driver including connecting with twin core wire and also matching to the adjacent ceiling surfaces carefully complete all as specified and directed. Note: The quoted price shall include the cost of Light and its driver. Make- Philips/Bajaj/ Havells/Wipro

S & F in replacement of LED indoor driver for LED fitting 10 to 35 Watts of the existing make including connection complete all as specified and directed

S & F replacement of LED indoor driver for LED pannel Recess mounted 2'x2' - 36 watts of the existing make ( Philips model no: E045C120V026N1AI) including connection complete all as specified and directed

S & F replacement of LED indoor Surge Protection Device suitable for LED panel Recess mounted -2'x2' - 36 watts of the existing make including connection complete all as specified and directed

M&L for cutting chases, pinning in making good to facing where required and pointing in cement mortar 1:3 to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc. and cutting chases for concealed water tubing or concealed conduit wiring etc. and making good, cutting not exc.10 cm girth all as specified and directed by engineer in charge Note : Making good of disturbed surfaces will be done by the contractor at his own cost i.e without any extra claim on this account from the Department

M&L for earthing complete with galvanised steel earth plate electrode including necessary excavation and earth work in any type of soil with galvanized steel earth plate electrode size 60 cm x 60 cm x 6 mm thick buried directly in ground (earth pit not less than 2.25 m below ground level) with top edge of the earth plate not less than 1.50 m below normal ground level connected to with and including earth lead of 4 mm dia GI wire up to 7.50m by means of bolts nuts check nuts and washers of galvanised iron or steel all as shown in electrical plate No.3 of MES SSR Part-I(2009) connected to main switch board or main control board all as specified and testing on completion with & including provision of earth wire protected by galvanised iron 40 mm dia. light grade pipe up 7.50m and watering pipe shall be 20 mm bore medium grade with and including concrete pit shall be PCC 1:3:6 type C-1, 40 mm thick pre cast cover slab in RCC (1:2:4) type B-1 using 20 mm graded stone aggregate duly reinforced with 8 mm TMT bars @100mm C/C on both sides with suitable cast iron lifting handle, GI earthing wire shall be encased in and including 50mm nominal bore GI 'light grade' tubing with all fittings from earth plate up to panel shall be provided & charcoal / salt funnel & other fittings etc. complete all as specified and as directed. Note :- (i) Unit rates includes the cost of 7.50 m GI pipe for protection of 4mm dia GI earth wire for each earthing.

M&L for Earth continuity conductor or main earthing lead fixed to wall on batten or recess or chases or buried in ground or drawn in conduit / pipe or fixed to poles or any other indicated situation for loop earthing etc as required for 32x6 galvanized iron strip, complete all as specified and directed.

M & L For fixing earth continuity conductor or main earth lead fixed to wall or buried in ground or drawn in GI pipe with 4 sqmm GI Wire complete all as specified and directed.

S&F in replacement down rod made out of GI pipe medium grade 15mm dia with fan clamps incl drilling cutting threding etc complete all as directed for ceiling fan 1200/1400 sweep of following sizes:- (a). 0.60 m long

(b). 1.20 m long

(c). 1.80 m long

M&L for PVC rectangular block of 100mmx100mm x 50mm deep size suitable for mounting switches, sockets, fan regulator etc with and including cover laminated sheet cover including making good of disturbed surfaces, complete all as specified and directed.

M&L for PVC rectangular block of 175mm x 100mm x 50mm deep size suitable for mounting switches, sockets, fan regulator etc with and including cover laminated sheet cover including making good of disturbed surfaces, complete all as specified and directed.

M&L for PVC rectangular block of 200mm x 150mm x 50mm deep size suitable for mounting switches, sockets, fan regulator etc with and including cover laminated sheet cover including making good of disturbed surfaces, complete all as specified and directed.

M&L for PVC rectangular block of 250mm x 200mm x 50mm deep size suitable for mounting switches, sockets, fan regulator etc with and including cover laminated sheet cover including making good of disturbed surfaces, complete all as specified and directed.

M&L for PVC rectangular block of 350mm x 300mm x 50mm deep size suitable for mounting switches, sockets, fan regulator etc with and including cover laminated sheet cover including making good of disturbed surfaces, complete all as specified and directed.

S&F in repair, Metal plug and socket -2 pin and earth plug and socket with 20Amps MCB SP concealed / surface on wall as per site requirement including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing complete all as specified and directed by Engr-in-charge (Make - L&T or equivalent in Legrand / ABB / Schenider.

S&F in replacement factory made epoxy powder coated Distribution Board TP & N 4 way double door (VTPN MCCB DB) MCCB as In comer, and MCB as outgoing with metal door (IP-43 protection) fabricated from CRCA sheet and fixed semi flush to wall and suitable for universal mounting and including 200 Amp copper bus bar, neutral bar, standard DIN rail, Earth bar and cable ties for cable management, top and bottom removable gland plates with Knockout semi flush to wall and making good disturbed surface and touch up with the same finishes complete all as specified and directed by Engr-in-charge Note: MCCBs and MCBs will be measured and paid seperately under respective item of BOQ.

Ditto all as per item no 61 above but TP & N 8 way double door (VTPN MCCB DB), complete all as specified and directed by Engr-in-charge

Ditto all as per item no 61 above but TP & N 12 way double door (VTPN MCCB DB), complete all as specified and directed by Engr-in-charge

S&F in repair IP-43, protection metal double door horizontal TPN -DB, 4 way rated busbar, 415 volts, 50 HZ complete with interconnection links, blanking plates, cable ties, identification labels SP / TP / TPN MCB as incoming / out going and concealed /surface on wall as per site requirement including all cutting holes in or through walls, making good to walls, ceiling etc including two coats of white / colour washing / distempering etc to the disturbed surfaces to match the existing, complete all as specified and directed by Engr-in-charge. Make - Legrand / ABB/L&T/ Schenider.

S&F in replacement MCB DB, 04 way SPN DB (double door), sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete all as specified and directed by Engr-in-charge Make - Legrand / ABB/L&T/ Schneider.

S&F in replacement MCB DB, 08 way SPN DB (double door), sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete all as specified and directed by Engr-in-charge Make - Legrand / ABB/L&T/ Schneider.

S&F in replacement MCB DB, 12 way SPN DB (double door), sheet metal enclosure factory made suitable for MCB DB's 240 volts with 200 amp rated busbar, neutral & earthing link bar, flush/surface mounting complete including taking down the existing DB of any type & size by removing from existing circuits and refixing the new DBs and circuits complete all as specified and directed by Engr-in-charge Make - Legrand / ABB/L&T/ Schneider.

S&F in repair MCCB with rating of 63-100 Amps,415Volts 4 pole with 16kA breaking capacity,thermal magnetic asdjustable of overload & short circuit release as per IS-13947 & IEC 60947-2 & the service short circuit breaking capacity (Ics) should be equal to ultimate breaking capcity(Icu).MCCB should be with suitable spreaders and phase barriers for each terminals, complete all as specified and directed by Engr-in-charge.

Ditto all as per item no 68 above but MCCB 125 Amps, 16 KA, 4 Pole, 415V, complete all as specified and directed.

Ditto all as per item no 68 above but MCCB 160 Amps, 25 KA, 4 Pole, 415V, complete all as specified and directed.

Ditto all as per item no 68 above but MCCB 200 Amps, 25 KA, 4 Pole, 415V, complete all as specified and directed.

Ditto all as per item no 68 above but MCCB 250 Amps, 25 KA, 4 Pole, 415V, complete all as specified and directed. Note for item nos. 68 to 72:- The MCCBs should have adjustable overload setting Ir+(08 to 1.0)'n.

S&F in replacement MCB SP 6-32 Amps,10KA, 'C' series complete all as specified and as directed.

S&F in replacement MCB SPN 20-40 Amps,10KA, 240V, 'C' series complete all as specified and as directed.

S&F in replacement MCB TP 40/63 Amps ,10KA, 415 V,'C' series complete all as specified and as directed.

S&F in replacement MCB TPN 40/63 Amps ,10KA, 415V, 'C' series complete all as specified and as directed.

S&F in replacement RCCB 40 Amps, 100mA, 2 Pole, 240V complete all as specified and as directed.

Supply and fixing in repairs PVC fresh air fan 250mm sweep complete all as specified and as directed. (Make :- Bajaj/crompton/Havells/Usha)

Taking down ceiling fan / exhaust fan of any sweep for servicing / repairing / maintenance, opening up, identifying and replacing the defective parts, cleaning, greasing etc, re-assembling and hanging up / fixing back at its original position, connecting up and testing complete all as directed. Note : 1.Cost of spares such as capacitors, bearings etc will be measured and paid for separately under respective Item of BOQ as supply only.

Supply only bearing No.6201/6202/6203 or any other No matching to the existing size and suitable for ceiling fan/exhaust fan/wall mounted fan, complete all as specified and directed. Make:- SKF or equivalent

Supply only capacitor of 2.5 mfd for ceiling fan / exhaust fan, complete all as specified and directed. Make:Tibcon/Epcos/Havells

Supply only capacitor of 4 mfd for ceiling fan / exhaust fan, complete all as specified and directed. Make:Tibcon/Epcos/Havells

M&L for replacement of burnt winding of Ceiling fan 1200/1400mm sweep working on 230 volts AC supply, rewinding complete with super enamelled copper wire of same guage and weight, replacement of insulation paper, varnishing, heating up and testing complete including taking down and refixing the fan at its original positions complete all as specified and directed by Engr-in-charge.

Ditto all as per item no. 83 above but Exhaust fan upto 250/300/450 mm sweep working on 230 volts AC supply, complete all as specified and directed by Engr-in-charge.

Ditto all as per item no. 83 above but Wall mounting fan of any 230/450 mm size,working on 230 volts AC supply, complete all as specified and directed by Engr-in-charge.

S&F high speed pedastal fan of sweep 400 mm complete all as specified and directed by Engr-in-charge.

Supply only Self adhesive PVC electrical Insulation tape 7 mtr long, ISI mark with superior quality complete all as specified and as directed.

Supply and Fix in replacement MS clamp with rubber reel, nuts, bolts, split pin etc. suitable for 1200/1400 mm sweep ceiling fan complete all as specified and as directed.

Disconnecting and taking down existing userviceable geyser of 25 ltrs capacity of any make/brand, taking it to civil workshop for repairing, servicing, cleaning etc, replacement of thermostat, heating element, indicator lamp and thermal cut out including fixing of PVC cable, sheathed, three core with stranded copper conductor of size 2.5 sqmm and refixing the geysers at location for, complete all as specified and directed by Engr-in-charge. Note:- Heating element, thermostat, indicator lamp & thermal cutout etc shall be measured and paid separately as supply only

Supply only heating element 1.5 / 2 KW, 230 volt round / triangular in shape ISI marked complete all as specified and as directed. Make:- Bajaj / Recold / Havells

Supply only Indicating lamp (red/green/yellow) complete suitable for geyser of any capacity complete all as specified and as directed.

Supply only thermostat and cutout set electronic type, temperature adjustable from 0-80⁰C suitable for geyser of 25 ltrs capacity.

S&F in replacement GI mesh hot water connection 600/900 mm long including necessary washers suitable for geysers of various capacities complete all as specified and directed.

S&F in repairs cable PVC insulated 3 core 2.5 Sqmm with stranded copper conductor 1100V grade from socket/switch to geyser complete all as specified and as directed.

S&F in repairs armoured copper cable PVC insulated 3 core 4.0 Sqmm with stranded copper conductor 1100V grade complete all as specified and as directed

S&F in repairs armoured copper cable PVC insulated single core 16.0 Sqmm with stranded copper conductor 1100V grade complete all as specified and as directed

S&F in replacement PVC insulated cable 2 core stranded copper conductor 0.5 sqmm all as specified and directed by Engr-in-charge.

S&F in replacement PVC insulated cable 2 core stranded copper conductor 1 sqmm all as specified and directed by Engr-in-charge.

Supply & fix in replacement 15A plug top and connection complete all as specified and as directed

S&F in replacement for white cover plate with frame 1 module, Make - as per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement for white cover plate with frame 2 module, Make - as per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement for white cover plate with frame 3 module, Make - as per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement for white cover plate with frame 4 module, Make:- as per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement for white cover plate with frame 6 module, Make:- As per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement for white cover plate with frame 8 module, Make:- As per the sample given, complete all as specified and directed by Engr-in-charge.

S&F in replacement switch piano flush button type 6 Amp single pole one way complete all as specified and as directed.

S&F in replacement switch bell push button type 5 Amp single pole complete all as specified and as directed.

S&F in replacement socket outlet 5 pin, 6 Amp flush type multipurpose complete all as specified and as directed.

S&F in replacement socket outlet 5 pin, 16 Amp flush type multipurpose complete all as specified and as directed.

S&F in replacement switch piano flush button type 16 Amp single pole one way complete all as specified and as directed.

S&F in repairs stepped electronic fan regulator flush type, two module on the existing phenolic laminated sheet etc as required, complete all as specified and directed.

Supply and fix electronic meters temper proof LCD display with polycarbonate cover for single phase, two wire system, 230 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH, single phase, complete all as specified and directed by Engr-in-charge. Make:- L&T / HPL / Havells / BENLO

Supply and fix electronic meters temper proof LCD display with polycarbonate cover for three phase, four wire system, 415 V, 10- 60Amp, accuracy class-I 50Hz, conforming to IS 13779, IP-54, with parameters to show data, time, current reading, load, PF, voltage and KWH, three phase, complete all as specified and directed by Engr-in-charge. Make:- L&T / HPL / Havells / BENLO

S&F in replacement of burnt out and unserviceable fan motor assembly with new one copper winding fan motor assembly complete including with double bearing, with metal plate top & bottom side suitable for usha or any other existing make fixed at any location complete all as specified and directed

Supply only terminal conductor 3 way bakelite, complete all as specified and directed by Engr-in-charge.

Supply only brass gun metal bushing suitable of size 1200/1400mm sweep ceiling fan, complete all as specified and directed by Engr-in-charge.

Supply and Fix in replacement canopy suitable for ceiling fans (Set of two), complete all as specified and directed by Engr-in-charge.

Supply and Fix in replacement MS clamp with rubber reel,nuts,bolts,split pin etc suitable for 1200/1400 mm sweep ceiling fan, complete all as specified and directed by Engr-in-charge.

M&L for Painting of ceiling fans complete in situ with one coat of synthetic enamel paint by spraying including filled the cavities with filler after cleaning all dust etc complete all as specified and directed.

M&L for replacement of phenolic laminated sheet at site as per reqmt including cutting groove to accomodate switch sockets 5A or 15 A complete all as specified and directed

Hanging only ceiling fan and connecting up including provision of cable from ceiling rose or connector to fan, complete all as specified and directed

S&F in replacement of 1 module Blanking plates for MCB DB outgoing circuit & switch board complete all as specifed and directed by Engr-In-Charge. Make: Vinay/Anchor Roma/Anchor Rider

RELIABLE ENTERPRISES

UNIQUE ENGINEERS

M/S CHANDAN BUILDERS

PAMS ENTERPRISES