GE/ ALP (8490) KOLKATA OF 2025-26

Amount

Demolition of Brickwork built in Cement Mortar including all Quoins, Arches, Pillars, etc. of any descriptions complete all as specified and as directed.

Material and Labour for brick work with sub class 'B' brick straight of curved on plan exc 6m mean radius built in CM (1:6) complete all as specified and as directed.

All as per Item No 2 here in before but except brick etc complete all as pecified and directed.

Material and Labour for Brick work with sub class B bricks straight or curved on plan to any radius in half brick thick wall built in cement mortar (1:4) complete all as specified and as directed.

Demolition of cement concrete (unreinforced) of any descriptions, below or above Ground floors (Floor Topping, Sub Base etc) not exc 150mm thick, above or below ground level complete all as specified and as directed.

Material and Labour for PCC (1:4:8) type D-2 (using 40mm graded stone aggregate) as in sub base of flooring complete all as specified and as directed.

Material and Labour for 100mm thick plain Cement concrete type B- 2, (1:2:4) (using 40mm graded stone aggregate) as in floor, hard standing and like complete all as speficied and as directed.

Material and Labour for 75mm thick PCC (1:3:6), type C2, (using 40mm graded stone aggregate) as in plinth protection / paving, surfae finished even & smooth without using extra cement as complete all as specified and as directed.

Demolation of cement concrete (reinforced) in any position (below or above G.L) etc complete all as specified and directed

M&L for RCC(Nominal Mix) in type-B1 (1:2:4) (20mm graded stone aggregate) pre cast slabs supported on walls for cup board and Kitchen slabs,manhole cover etc complete all as specifed and directed.

M&L for mild steel TMT bars 10MM dia and over, cut to length, bent to shape required including cranking, bending, hooking ends and binding with mild steel wire (annealed) not less than 0.9mm dia or securing with clips quality conforming complete and all as specified and directed.

M&L for mild steel TMT bars of 5mm dia and over upto and including 10mm dia in stirrups, spacers and binders cut to length bent to shape required including cranking bending spirally for hooping for column, hooking ends and binding with and including MS wire (annealed) not less than 0.9mm dia complete all as specified and directed.

Taking down cement plaster of any description built in cement mortar on brick or stone walls etc including racking out joints, hacking for Key, scrubbing down with water etc.complete all as specified and as directed.

Materials and labour for 15 mm thick rendering on fair faces of brick work in cement mortar (1:6) and finished the surfaces even and smooth without using extra cement complete all as specified and as directed.

Material and labour for 5mm thick rendering in cement mortar (1:3) on concrete surface as in ceiling and finished the surface even and smooth without using extra cement ,complete all as specified and as directed.

M&L for Rendering 15mm thick plaster in CM (1:4) on fair faces of brick or concrete surface of wall and finished even and smooth without using extra cement, complete all as specified and directed.

Dismantling of Plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof covering, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc, upto 4 storey bldg, complete all as specified and directed.

S&F Pre- painted galvalume aluminum zinc coating GI based plain steel sheet 0.50mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall, fixed with self tapping screws etc, upto 4 storey bldg, complete all as specified and directed.

Cutting chases, pinning in, making good to facings where required and pointing in cement mortar (1:3) to ends or edges of landings, steps, cills, sunshades, shelves, lintels, etc.; and cutting chases for inseritng roof sheet in wall, etc., and making good, cutting not exc 10 cm girth in brick wall. upto 4 storey bldg, complete all as specified and directed.

Dismantling timber scantling 40 sq cm and over in section, (framed work) in any position complete all as specified and directed.

S&F Steel work of MS Square/round pipe or angles, Tee etc as in purlin, rafter, post and trusses including special shaped washer etc. complete using ERW or induction butt welded tubes conforming to I. S.1161- 1979 grade St.-240, complete all as specified and directed.

Dismantling wall and ceiling boards (fibre, pulp, insulation etc.) any thickness, including cover fillets, complete all as specified and directed.

M&L for suspended false ceilling system using metalic exposed suspende system, grid section size (600mm x 600mm) comprising of GI powder coated main runner of dimension (39 mm x 24mm x 0.80mm) thick ( thickness comprising of GI/0.4+ PPPCGS/0.3mm & weight of Runner 1.35 kg for 3600mm length) Cross Tee of dimensions (29mm X 24mm x 0.8 mm) thick wall angle (22.2mm x22.2mm x 0.65 mm thick ) thickness comprising of GI/0.35 + PPPCGS/0.3 mm & Weight of angle 0.70 kg for 3050 mm length) with and including 6 mm thick calcium silicate board of siliceous and calcareous material reinforced with cellulose fibre for fixing in (600mm x 600mm) grid ( placed in the grid system duly suspended with 4 mm dia G I bars hangers fixed with steel dash through fasteners from purlins of the roof with necessary fittings and fixtures etc complete all as specified and directed.

M&L for 10 mm thick Gypsum board false ceiling joint less work including application of putty over gypsum board to achieve smooth and joint less celing surface and applying two coat of oil bound distemper over a coat of primer in ceiling surfaces including framed work for consisting of 60 mm wide GI steel 'C' section of as in main of 0.71mm thick and 60 mm GI channel section as in cross member of 0.63 mm thick and GI steel angle section as in suspenders of size (25x20x0.63 mm) and wire cloth of 0.71 mm dia of wire and (100x50)mm aperature size including cutting , riveting, steel fastener, drilling holes in RCC roof and securing with screws etc complete all as specified and directed.

M&L for POP cornice width n.exc 200mm wide in ceiling edge of any design and shape ,complete all as specified and directed.

S&F in repair 6 mm thick Gypsum board/calcium silicate board tiles of size (600x600) mm incl proper hanging arangement as required complete all as specified and directed.

S&F in repair Solid PVC Wall Lining consisting of 5mm thick Plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame including 5mm thick PVC fillets of width 35mm with interval of 500mm in both horizonatal and vertical directions including necessary caping/beading/fillets at top and junctions or any other locations required as per site etc, complete all as per specified and directed.

S&F in repair PVC caping/fillets at top and junctions required as per site condition PVC panelling etc complete all as per specified and directed.

Dismantling bitumenous felt of any type and disposed of the same complete all as specified and directed.(Up to 12 storey Bldg)

M&L for PCC (1:2:4) type B0 using 12.5 mm graded stone aggregate, as roof kerbs/pading, with water proofing compound etc complete all as specified . (WPC will be measured and paid seperately).

M&L for Water Proofing Treatment on existing cleaned RCC Roof with the following Specifications and Manufacturer's instructions, complete all as specified and as directed :- (a) Rendering 10mm thick in Cement Mortar (1:4), Plastered Surfaces finished Even and Smooth. The Plastered Surfaces shall be cured properly for 7 Days by Ponding of Water over Roof. (b) Preparing and cleaning of fully dry Plastered Surfaces as per IS:3067-1966. (c) Applying Bitumen Primer conforming to IS-3384-1986 over the Cleaned Plastered Surface @ 0.30 Litre per Sqm. (d) Applying evenly One Coat Blow Hot Bitumen of grade 85/25 @ 1.20 Kg per Sqm on Primed Surfaces. (e) Applying a layer of APP based Polymeric Membrance 3.0mm thick (minimum) weighing 3.50 Kg per Sqm (reinforced) with Polyster Non-woven Fabric weighing not less than 160 Grams per Sqm by Torch application. The Overlaps shall be minimum 100mm on the Transverse direction and 75mm on Longitudinal direction. (f) Applying One Coat of Aluminium Paint @ 0.10 Litre per Sqm over APP based Polymeric Membrane.(Up to 12 storey Bldg)

Dismantling of floor hearth or wall tiling incl cement mortar bedding ( but not backing) and removing debris and rubbish off the premises, complete all as specified and directed.

M&L for Non - skid Ceramic tiles 7 to 8 mm thick (square/rectangular) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, infloors etc. set and jointed in neat cement slurry andpointed in white or colouredcement to match the shade of tiles over and including Screed bed or bedding layer 15 mm thick in cement mortar (1:6) for laying floor finishes complete all as specified and as directed.(upto 12 storey High of building)

All as per item No 34 here-in-before but fixed on vertical surface as in skirting including 10mm thick cement plaster in cement mortar (1:4), complete all as specified and directed

Material and labour for colour printed glazed ceramic tiles (Premium quality) (450X300mm) X 7mm thick as in vertical surface of walls set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including 10 mm thick cement plaster in cement mortar (1 : 4), complete all as specified and as directed.

Material and labour for double charged vitrified coloured/ light shade tiles (Premium Quality) of size (600x600mm) x (8-9)mm thick in floor, etc set and jointed in neat cement slurry and pointed in white cement mixed with pigment to match the shade of tiles over and including 15 mm thick screed bed in cement mortar (1 : 6 ) for laying of floor finishes, complete all as specified and as directed.

All as per item No 37 here-in-before but fixed on vertical surface as on skirting including 10mm thick cement plaster in cement mortar (1:4), complete all as specified and as directed.

Material and labour for (16-18)mm thick granite (of any type) work (table rubbed and polished) in steps, jambs, pillars, window-cills, cooking platforms and like including 15mm thick cement mortar (1:4) including pointing in white cement (1:2) using marble dust with admixture of pigment to match with shade of granite including taking down stone slab or stones, complete all as specified and as directed.

Rounding to edges of stone slabs one edge, such as in steps, coooking platform and other similar situations complete all as specified and directed.

Dismantling wrought iron or mild steel work of any description as in door, gates etc and similar works complete all as specified and directed.

S & F framed work such as grills, gratings, etc. with ends of bars shouldered and /or riveted or forged into spikes, framed guard bars barred iron doors; ladders framed alusters; wald ways; railings; framework of water tanks and similar work confrming to Fe-290 Gde -E 165 complete all as specified and directed.

Taking down steel window/ventilator including guard bar of any description and in any position and removing from site, complete all as specified and directed upto 12 storied bldg.

Taking down chowkhat or frames with shutter not exc. 1.50 Sqm each (without taking of shutters from the frames), complete all as specified and as directed upto 12 storied bldg.

Taking down chowkat or frames with shutter exc. 1.50 Sqm but n.exc. 4 Sqm each (without taking of shutters from the frames) upto 12 storied bldg, complete all as specified and as directed.

Taking down wooden shutters of any description exc 1.00 Sqm but n.exc 2.00 Sqm each upto 12 storied bldg, complete all as specified and as directed.

M&L for easing adjusting of steel window and oiling greasing for smooth functioning including replacement of unserviceable peg stay , handle and nessessary welding for broken hook or glazing bar upto 12 storied bldg, complete all as specified and directed.

M&L for easing adjusting of aluminum window and refitting of shutter section with screw including replacement of unserviceable locking arrengment ,stay hook and nessessary neoprene beading upto 12 storied bldg, complete all as specified and directed.

S&F stay/ handle cleat as per requirement at site and welded complete for fixing of handle /stay in steel windows including taking down old one complete all as specified and as directed.

Taking down wooden shutters of any description exc 1.00 Sqm but n.exc 2.00 Sqm each and refixing the same in the same opening upto 12 storied bldg, complete all as specified and as directed.

Hacking out old/broken glass (any description, size and quality) upto 12 storied bldg, complete all as specified and directed.

S&F mild steel flat iron of size (25x3) mm or equivalent as required for hold fasts and clamps & similar small articles confirming to Fe-410-O or Fe-310-O upto 12 storied bldg, complete all as specified and as directed.

Material and labour for PCC (1:3:6) type C-1 (using 20mm graded stone aggregate) as in hold fast, bed plates, copings etc. including necessary formwork upto 12 storied bldg, complete all as specified and as directed.

S&F 2nd Class HW Plain, solid, straight chowkats and frames, wrought framed rebated on the solid, rounded or chanfered, put together with glue pinned at joints, complete all as specified and as directed. (upto12 storey High of building)

S&F 30mm thick factory made flush door shutters solid core construction with block board core and plywood face panels commercial type on both faces upto 12 storied bldg complete all as specified and as directed.

S&F 35mm thick 2nd class hard wood gauged & skelton shutter, open rebated & prepared to receiv e gauged, ( without sase bar ) eadge of framing plain, chamford or rounded, fitted with cut & mitred beads for securing gauged etc, complete all as specified and directed.(upto 12 storey High of building)

S&F solid PVC door frame of size (50mm x 47 mm) made out of 5 mm plain colour PVC sheet reinforced with MS Square tube in opening all as shown on drawing and specified upto 12 storied bldg, complete all as specified and directed.

S&F factory made solid panel PVC Moulded door shutter 28 to 30 mm thick style with 2 mm thick prelaminated Moulded PVC sheet polyurethane painted on front face & 2 mm plain colour PVC sheet on back faces, and with particle board core supplying and fixing in frame at site as per specification and drwaing upto 4 storied bldg, complete all as per specification and drawing.

S&F Steel windows with side hung shutters including projecting type hinges with steel handle, and steel peg stay, complete with glazing bars, dovetailed or welded for receiving glass and including cutting holes in wall for fixing the window and making good the disturbed surfaces with the existing finishes to match upto 12 storied bldg. complete all as specified and as directed.

All as per item no 59 here in before but without glazing bars complete all as specified and as as directed.

S&F steel ventilators with tope hung shutters including hinges with steel handle and steel peg stay,Glazing bar dovetailed or welded for receiving glass and including cutting holes in wall for fixing the ventilator and making good the disturbed surfaces with the existing finishes to match upto 12 storied bldg, complete all as specified and as directed.

S&F Powder coated aluminium sliding windows for three track with rubber gasket, stopper powder coated aluminium standard beads/glazing clips ,locking arrangement etc and aluminium frame of size (80mmX25mmX1.55mm) and shutter of section (20mm X20mm X1.55mm) incl ( two shutter of 4.8mm thick glass and one shutter of wiremesh 0.36 mm dia of wire and average width of aperture 1.40 mm) with and including Deco grill ofweight per sqm 2.45 Kg as required and taking down of old rusted steel / Aluminium window with grill with necessary all fittings complete all as per manufacturer's instructions and all as specified and as directed.

S&F in repair aluminium anodised Partition wall of frame size (80mm x 38mm x 3.00 mm) with standard beads/glazing clips, locking arrangement etc with necessary all fittings complete all as per manufacturer's instructions and all as specified and as directed.

S&F in repair powder coated aluminum ventilator (single leaf single shutter) side hung type with stainless steel butt hinges, one shutter glazed with and including 4.00mm thick plain sheet glass and other shutter with stainless steel wire cloth of 0.36 mm dia of wire and average width of aperture 1.40mm fixed with stainless steel wire staples, rubber gasket, stopper,aluminium anodised handle 100mm long ,aluminium anodised tower bolts 100mm long and peg stay etc, size of aluminum frame shall be (100mmx50mmx1.50mm) and shutter frame shall be (40mmx20mmx1.50mm) including deco Grill of weight per sqm 2.45 kg as required and taking down of old rusted steel ventilator complete all as specified and as directed. Note : 1 No Glazed shutter and 1 No Gauged shutter constitube one unit.

S&F powder coated aluminium ventilator louvre type with frame, aluminium section weighing 0.55 kg/m including 4 mm thick glass / SS wire mesh necessary joining cleats, glazing clips, rubber packing, side handle fixed to wall with fastners including deco grill (specification as above) as require and taking down of old ventilator of any type etc complete all as specified and directed.

S&F stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel staples in steel/wooden /aluminium frames complete upto 12 storied bldg all as specified and as directed.

S&F in repairs stainless steel wire cloth of 0.36 mm nominal dia of wire and average width of apperture 1.40 mm and fixed with stainless steel staples in steel/wooden /aluminium frames complete upto 12 storied bldg all as specified and as directed.

S&F 3mm thick Sheet glass, ordinary quality and glazing with oil putty in square n.exe 0.50 Sqm in each pane complete upto 12 storied bldg all as specified and as directed.

S&F 4mm thick figured glass, ordinary quality and glazing with oil putty in square n .exe 0.50 Sqm in each pane upto 12 storied bldg complete all as specified and as directed.

S&F 4.8mm thick Sheet glass, ordinary quality and glazing with oil putty in square exe 0.50 Sqm in each pane complete all as specified and as directed upto 12 storied bldg.

S&F in repair 18/19mm thick prelaminated particle board interior grade, prelaminated one side with decorative choice laminations and other side balancing white lamination fixed with screws to timber frame work as in kitchen cabinet shutter including external teak wood lipping 6mm thick fixed with nails upto 12 storied bldg complete all as specified and as directed.

S&F in repair 2nd class hard wood Plain fillets, square, rectangular or triangular in section, wrought, secured with nails or brads, sectional area exc 3.00 Sqcm & n exc 6.00 Sqcm upto 12 storied bldg complete all as specified and directed.

S&F in repair 12mm thick plywood in cupboards complete all as specified and directed upto 12 storied bldg.

S&F in repair for curtain rods dicorative aluminium alloy with fixing brackets including taking down old pelmet box complete all as specified and directed.

S&F in repairs 20/25mm fancy type bracket for drapery rods anodized aluminium alloy complete all as specified and directed upto 12 storied bldg.

S&F in repair floor door stopper of aluminium alloy body and tongue with hard drawn steel spring, overall length cover plate 150mm complete all as specified and as directed.

S&F in repair 75mm size Mild Steel butt hinges medium weight, cold rolled complete all as specified and as directed.

S&F in repair 100mm size Mild steel butt hinges medium weight, cold rolled complete all as specified and as directed.

S&F 30mm width of flap continious piano hinges mild steel,bright finish or electro galvanised complete all as specified and as directed.

S&F magnetic catches 50 mm long of any description complete all as specified and directed.

S&F in repair 150mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F in repair 200mm long Aluminium, anodised, barrel tower bolts of extruded section complete all as specified and as directed.

S&F In repair 250mm long aluminium alloy anodised sliding door bolts with hasp staple (Bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section complete all as specified and as directed.

S&F 40mm dia cupboard knobs of brass fixed with nut, screw and washer complete all as specified and as directed.

S&F in repair 75mm Hasp and staple, safety type brass with mild steel hinge pin including bolt to hinge plate and fixed with screws complete all as specified and as directed.

S&F in repair 100mm long Aluminium,anodised extruded handle fabricated type, complete all as specified and as directed

S&F in repair 150mm long Aluminium,anodised extruded handle fabricated type, complete all as specified and as directed

Supplying and fixing in repair 1.25mm thick steel rolling shutters, with out ball bearing, as specified including top cover, anchoring rod, hasp and staple and one shop coat of red oxide primer; erected in position as indicated, complete: push pull or manual typecomplete all as specified and as directed.

Oiling/greasing existing rolling shutters for easing adjusting for smooth functioning of steel rolling shuttercomplete all as specified and as directed.

S&F lock plate bracket made of angle (40X40X5) mm, flat (25X6) mm, cleat, latice flat & locking arrangement etc of rolling shuttes including necessary welding / riveting and one coat of red oxide primer incl taking down old lock plate complete all as specified and directed.

S&F mild steel slot profiles of 1mm thick including taking down old profiles complete all as specified and directed.

S&F as in repair mortice lock set combipack with 6 lever and with decor brass handle set complete all as specified and as directed. Make : Godrej Cat No 8286 or equivalent approved make.

S&F in repair aluminum (extruded section Body) body door closer hydraulically regulated design No 3( Make Hyper) suitable for door shutters of 851 to 1000 mm in width and of weight between 61 to 80 kg all as directed.

Material and labour for preparation of new wooden surfaces of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and as directed.

Material and labour for preparation of new steel surfaces of any description over 10cm width or girth and applying two coats of synthetic enamel paint over a coat of red oxide zinc chrome primer complete all as specified and as directed.

Resecuring or easening, adjusting without taking down of shutters exc 1 Sqm and n.exc 2 Sqm each in situ complete all as specified and directed.

Dismantiling brick work built in CM for making AC opening in existing wall incl making good the adjacent area with cement and distemper etc including second class hard wood frame 50x40mm complete all as specified and directed.(Appx area 0.5sqm each)

Taking up or down 15mm steel tubing and connections, including cleaning for re-fixing or removal complete all as specified and directed.

Taking up or down 20mm steel tubing and connections, including cleaning for re-fixing or removal complete all as specified and directed.

Taking up or down 25mm steel tubing and connections, including cleaning for re-fixing or removal complete all as specified and directed.

Dismantling cast iron or re-inforced concrete drain pipes of 100mm bore, jointed in cement mortar complete all as specified and as directed.

Taking down eaves gutters and rainwater pipes (any size or pattern), including all fittings,heads, shoes, bends, swan-necks,etc., including cleaning or refixingor removal to Store (measured overall as fixed along the centre line over fittings and accessories) complete all as specified and directed.

M&L for cutting chases, pinning, in making good to facing where required of of brick wall and pointing in cement motrar (1:3) to ends and cutting chases for concealed water tubing and concealed conduit wiring ete and making good surfaces complete all as specified and directed.

Supplying and laying for 20 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls including all brass fitting/fixtures in any grade to receive plumbing fittings and fixtures complete all as specified and directed

Supplying and laying for 25 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls including all brass fitting/fixtures in any grade to receive plumbing fittings and fixtures complete all as specified and directed

Supplying and laying for 32 mm outer dia of CPVC pipes SDR 11 & Plain CPVC SDR 11 fittings in trenches/walls including all brass fitting/fixtures in any grade to receive plumbing fittings and fixtures complete all as specified and directed

S&F in repair 20mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed.

S&F in repair 25mm bore gun-metal, globe or gate valves, with iron wheel head, screwed both ends for iron pipes complete all as specified and as directed.

S&F CI spun pipes with out ears in any length fixed to wall with brackets of 100mm bore including bitummous paints both side complete all as specified and as directed.

S&F CI bend with door of 100mm bore, complete all as specified and as directed.

S&F CI branch pieces single equal or unequal with door of 100mm bore, complete all as specified and as directed.

S&F CI 'T' of 100mm bore, complete all as specified and as directed.

S&F CI cowl of 100mm bore, complete all as specified and as directed.

Taking down Eaves gutter, rain water pipes(any size and pattern) including all fitting,bends, shoes, swan neck etc inculing cleaning and removing from site etc, complete all as specified and directed.

S&F 110mm bore PVC(SWR) pipe single socket in any length rubber ring joints, complete all as specified and as directed. (upto 04 storey High of building)

S&F 110mm bore PVC(SWR) pipe bend single socket ,complete all as specified and as directed.

S&F 110 mm dia PVC (SWR) junction single, (singleT), equal or unequal fixed to wall upto any height of the building, complete all as specified and as directed.

S&F 75mm bore PVC(SWR) pipe single socket in any length rubber ring joints, complete all as specified and as directed. (upto 04 storey High of building)

S&F 75 mm bore PVC(SWR) pipe bend single socket, complete all as specified and as directed.

S&F 75 mm dia PVC (SWR) junction single, (single T), equal or unequal fixed to wall upto any height of the building, complete all as specified and as directed.

S&F in repair ball valve including nessesary fittings fixed to existing flushing cistern, complete all as specified and as directed.

S&F in repair wall mixture non telephonic brass CP tap for mixing hot and cold water including three joints to 15 mm bore pipes or union and pluging and screwing to wall complete all as specified and directed.

Supplying and fixing in repairs wash hand basin mixture, 15mm bore dia, fancy type brass chromium plated for mixing 'Hot' and 'Cold' water including three joints, screwed both ends for iron pipe or for unions and pluging upto four storied of building complete all as specified and as directed.

S&F in repair spindle for 15 mm bore bib cock / stop cock / pillar tap complete all as specified and as directed.

S&F in repair brass CP knob for 15mm dia bib cock/pillar cock concealed stop cock complete all as specified and as directed.

S&F in repair 15mm dia PVC connection pipe 600mm long with PTMT nuts complete all as specified and as directed.

S&F in repair 10 litres capacity PVC valveless, syphonic action type, flushing cistern, white colour, low level, white with inlet, ball valve, float and handle including brackets duly painted, 32mm dia PVC flush pipe complete all as specified and as directed. (upto 12 storey High of building).

S&F in repair 32 mm dia PVC flush pipe of polyethylene of low or high density for low level cistern/kitchen sink/WHB complete all as specified and as directed.

S&F in repair chromium plated peg set of 6 with screws complete all as specified and as directed.

S&F in repairs Vitreous China wash basin ( white), flat back, size (580 x 450 mm), excluding taps, waste,chain and plug and porcelain stopper but including brackets, complete all as specified and as directed.

S&F in repairs Vitreous China wash basin (coloured), Pedestral pattern, boul size (580 x 450) mm, excluding taps, waste,chain and plug and porcelain stopper but including brackets, complete all as specified and as directed.

S&F in repairs Vitreous China wash basin (coloured), oval shape of size (560x480) mm for counter top, excluding taps, waste,chain and plug and porcelain stopper but including brackets, complete all as specified and as directed.

S&F in repairs 1mm thick of stainless steel kitchen plate rack of size (750mm x 900mm) including all fixing arrangement complete all as specified and as directed.

S&F in repair sinks with drainage board made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and waste; including bedding in cement mortar to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size (915mm x 460mm) bowl size (410mm x 330mm x 160mm) and including 32mm waste coupling of PTMT (half or full threaded) Minimum weight 32mm-45gms/40mm-60 gms) complete all as specified and directed.

S&F in repair Corner glass shelf assembly consisting of 5.5mm thick sheet glass shelf 300mm long complete all as specified and directed Make: Prayag or equivalent make as approved by GE(upto 04 building).

S&F in repair sheet glass shelf assembly consisting of 5.5mm thick sheet glass shelf 12cm wide with chromium plated bracket guard and railing 60cm long complete all as specified and directed Make: Prayag or equivalent make as approved by GE

S&F in repair chromium plated soap dish holder complete all as specified and directed.

S&F in repair towel rail of brass chromium plated tube 19 to 20 mm dia 600 mm long `D' type complete fixed in repairs with brass chromium plated screw complete all as specified and directed.

S&F in repair vitreous china squatting pan of orissa pattern long pan of size (580 mm x 440mm) with integral foot rest white with cast iron p or s trap with back inlet including flush pipe of suitable length to connection with existing cistern & make good complete all as specified and as directed.(upto12 storey High of building)

S&F in repair Vitreous China wash down water closet pan (pedestal pattern), white (excluding fixing bolts, flushing cistern and flush pipe) complete all as specified and directed

S&F in repair Health faucet (ABS Body) mild steel chromium plated suitable for 15 mm dia pipe with 1.25 metre long flexible tube and ABS wall hook including making connections and fixed in position complete in all respect as specified upto 4 storey

S&F in repair Chromium Plated towel ring square with round flange complete all as specified and as directed.

S&F in repair PVC water closet seat cover heavy duty coloured closed pattern with flat bottom and cover and mild steel CP hinnging device complete all as specified and directed.

S&F in repairs 15 mm bore two way Bib tap CP, screwed down screwed for iron pipe complete all as specified and directed.

S&F in repairs 15 mm bore two way Angular Stop cock CP, screwed down screwed for iron pipe complete all as specified and directed.

S&F in repair 15mm bore Brass CP bib cock fancy type chromium plated with crutch or butterfly handle, screwed down, screwed for iron pip or for brass ferrule and complete all as specified and as directed.(upto 12 storey High of building)

S&F in repair concealed 15 mm bore CP stop cock with sliding flange 15 mm complete all as specified and directed.

S&F in repair pillar taps made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as specified and directed.

S&F in repair brass CP shower roses with or without swivel joints,with shower arm, 125mm size, including fixing to steel pipes or union complete all as specified and as directed.(upto 12 storey High of building)

S&F in repair angular stop cock made of brass chromium plated screwed both ends for iron pipe for 15mm bore complete all as directed.

S&F in repairs 15 mm dia bib tap standard of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight 15mm-90gms/20mm-125gms)

S&F in repairs 15 mm dia pillar taps of PTMT any colour high pressure screwed for iron pipe and fixed complete all as specified and directed.(Minimum weight 15mm-110gms)

S&F in repairs 15 mm dia stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-112gms) complete all as specified and directed.

S&F in repairs 15 mm dia angle stop valve of PTMT any colour high pressure screwed for iron pipe and fixed (Minimum weight 15mm-90gms/20mm-112gms)complete all as specified and directed.

S&F in repair cast iron floor traps with steel grating jointing to waste pipe fixed in cement concrete Type B1 (1:2:4) 100 mm dia. Complete all as specified and directed.

S&F Vitreous China urinals,Half Stall type (back or corner wall type), complete including providing and fixing plugs, bedding urinal against wall in cement mortar (1:2), securing urinal to plugs with and including 60mm long brass screws, pointing around urinal back in cement; fixing automatic flushing cistern with brackets, flush pipe, grating and Union for discharge pipe. including Waste cupling, Urinal Spreader of PTMT of any colour fixed with 15mm dia pipe complete all as specified and directed.

S&F Vitreous china urinal partition white of size (310x700) mm. complete all as specified an directed.

Materials and labour for Preparation of new plastered surfaces of ceiling and applying three coats of white wash on ceiling surface etc complete all as specified and as directed.

M&L for preparation of the uneven surfaces of walls and applying two layer of wall care putty after complete removal of existing treatment all as specified and directed.

Material & labour for preparation of new plastered surfaces of wall and applying two coats of oil bound distember over a coat of primer upto 12 storey bldg complete all as specified and directed.

M&L for preparation on new plastered surfaces of wall and applying two coats of cement base paint over a coat of primer complete all as specified and directed.(Upto 4 storey of bldg)

M&L for preparation of old decorated surfaces by complete removal of existing surface brooming down or steel wire brushing scrapping down smoke soot and greasy spots and applying two coat of cement base paint on walls complete all as specified and directed. (Upto 12 storey of bldg)

M&L for complete removal of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds,et and applying one coat of cement base paint on walls complete all as specified and directed. (Upto 12 storey of bldg)

M&L for Preparation of old plastered surfaces and applying one coat of oil bound distemper on walls complete all as specified and as directed.

M&L for Preparation of old plastered surfaces and applying one coat of synthetic enamel paint on walls complete all as specified and as directed.

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds,etc and applying one coat of anti-algae and anti-fungal exterior grade weather coat paint over a coat of primer complete all as specified and directed. (Upto 12 storey of bldg)

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds,et and applying one coat of white wash on walls complete all as specified and directed.

M&L for preparation of old decorated surfaces by brooming down or steel wire brushing, scrapping down smoke soot, moulds,etc and applying one coat of white wash on ceilings complete all as specified and directed.

M&L for preparation of old steel surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for preparation of old wooden surfaces of any description over 10 cm width or girth and applying one coat of synthetic enamel paint complete all as specified and directed.

M&L for complete removal of existing treatment, preparatory to distempering, priming plastered and other surfaces with chalk whiting and applying two coats of OBD on wall complete all as specified and directed.

Dismantling and removing all unsound/weak concrete materials from slabs , lintel,chajja, fin, facia etc. by any means as directed by engr-in-charge including tapering all edges, making square shoulders of cavities air or sand blasting etc and cleaning of exposed concrete surface of lightly picking materials by air blasting or sand blasting incl foreign matrials , loose concrete/aggregate etc and disposal of all debris out of MOD land upto ten storey bldg and complete all as specified and as directed for 25mm average thickness.

M&L for removing of concrete all around reinforcement including from behind the reinforcing bars to give an avrage 25 mm (but not less than 15 mm clear air gap) by manual methods (using wire brushing, chiselling etc) and applying alkaline rust removing chemical followed by removing rust by emery paper and cleaning the area throughly by water and allow it to dry all as per manufacturer,s instruction to give it a totally rust free finished steel surface upto ten storey bldg complete all as specified and directed upto 12 mm dia bar. Make: SIKA/FOSROC or equivalent make as approved by GE

M&L for prepration of exiting reinfoecement surface by brush and application of two coat of Epoxy Zinc rich primer on the prepared steel surface excluding behind the bar by brush the primer shall have a minimium specific gravity 1.75 minimum weight minimum adhesive bond strength with steel is 1.5N/mm2 complete all as specified and directed. Make: SIKA/FOSROC or equivalent make as approved by GE.

M&L for providing single coat of epoxy bond adhesive of prepared non metallic surface (existing surface) and applying by brush all as per manufactures instruction/specification. The bonding agent shall have minimum compressive strength of 40 N/Sqmm and complete all as specified and directed upto ten storey bldg.

M&L for introducing new reinforcement bars up to 12mm dia for structural connections in RCC Bram, Lintels, Columns and slabs uncluding power drilling holes of appropriate diameter in reinforced of plain cement concrete to a minimum depth of 150 mm and upto 200 mm including power drilling , fixed the reinforcement in position using epoxy of loose dust by blowing air, sealing with epoxy cartridges etc upto ten storey bldg complete all as specified and directed.

Supply, mixing for providing and applying at two component structural grade polymer modified reinstatement morter, up to the thickness of 15mm over a coat of epoxy resin boanding agent as per manufacturer instruction . where local spalling has taken place or shuttering is not possible . The morter can be applying in layers not exceeding 6mm thick in each layer in and upto any thickness in smaller vertical pockets and upto any thickness in horizontal applications. The mortar should have a minimium compressive strength 12N/mm2 in 1 day and 45N/mm2 in 28 days. Minimum flexural strength should be 8 N/mm2 in 28 days. A modified styrene butadience emulsion for use as a bonding aid and gauging liquid for cementious system to be mixed with cement slurry before the application of modified polymer mortar to be used @ 6 ltr/bag of cement. The bonding agent should have minimium compressive strength 24N/mm2. Minimum tensile strength 3.5N/mm2, minimium flexural strength 6.5N/mm2 complete all as specified and directed upto 25 mm average thickness and upto ten storey High. Make :- Sika/Fosroc or equivalent make as approved by GE NOTE:- Cement and sand morter in proportion of (1:2) graded coarse sand ) with polymer admixed in proportions approved by Engr-in-charge)

M&L for supply, mixing and placement of micro concrete cement based prepacked single component chloride free sulphate free, non-shrink, free flow etc compacting, ready to use after mixing water in specified portion and in required thickness as per manufacturer instruction including necessary form work . compressive strength (ASTM C 109,cm cube ) of 35 MPa at 28 days including application curing compound at various location in bldg complete all as specified and directed

M&L for applyingof high efficiency polymeric resin base film forming curring compound or equivalent, Over concrete surface with max coverage area 5.0 sqm per liter as per manufactures instructions, upto ten storey building, complete all as specified and directed. Note: Works against all items contained in the BOQ have to be carried out upto and including 12th floor of the Bldgs and quoted rates shall be deemed to be included to this factor

M/S J S ENTERPRISES (BID ID -3395314)

R.R.ENTERPRISE (BID ID -3395398)

NESAIL CORPORATION (BID ID -3395645)

DK CONTRACTOR (BID ID -3393419)

M/S RAJESH TRADING CORPORATION (BID ID -3393103)

GAYATRI ENTERPRISE (BID ID -3394610)

DILIP CONSTRUCTION (BID ID -3393287)

GOODWILL AND CO. (BID ID -3393117)