REPAIR TO JOINERY, FLOOR, RENDERING, PLUMBING SANITARY FITTING WORKS IN NEW PROJECT AREA AT AF STN AT NAL

Amount

Demolition of RCC of any description and in any position not other wise specially provided for (reinforcement cut as required to faciliate demolition ) complete all as specified & directed.

Material and labour for reinforced cement concerete(1:2:4) type B-1 (nominal mix) (using 20mm graded crushed stone aggregate ) as in slabs supported on walls, beams, columns, shelves and like complete all as specified & directed. Note :- Reinforcement shall be measured and paid for separately.

Use and waste of Formwork to soffits of suspended slab such as roof slab, floor slab, landing and similar work; flat rough finished surfaces of concrete complete all as specified & directed.

Use and waste of Formwork to edges of concrete flats, treads, floor and roofs n exc 20 cm wide and sides of RCC/PCC bands in walls, horizontal or sloping and similar work exc 10cm but n exc 20cm wide, complete all as specified and directed.

Material and labour mild steel TMT Bars 6 to 8 mm and above cut to length bend to shape required including cranking bending spirally for column, hooking ends & binding with and including mild steel mild steel wire (annealed) not less that 0.90 mm dia or securing with chips complete all as specified and directed.

Demolition of cement concrete (unreinforced) of any description and in any position not other wise specially provided for and including floor finishes and removing the rubbish outside MoD land complete all as specified & directed.

Material and labour 75mm thick PCC 1:3:6 type C-2 ( using 40mm graded crushed stone aggregate) as in plinth protection laid in alternate bays, surface finished even & smooth without using extra cement including making joints complete all as specified and directed.

Material and labour 25mm thick PCC (1:2:4) type B-0 ( using 12.5mm graded crushed stone aggregate) as in sub base of floor surface finished even & rough to receive floor topping complete all as specified and directed.

M & L 15mm thick plastering/screed bed or bedding layer in CM(1:4) on brick/concrete surfaces as in sunken floor mixed with water proofing compound as per manufacturers instruction even and smooth without using extra cement, complete all as specified and as directed. Note :- WPC measured and paid separately.

Applying a tack coats of industrial bitumen 85/25 grade at the at the rate of 1.2kg per sqm as in sunken floor portion including preparation plaster concerte surface complete all as specified

Supply only intergal water proofing compound complete all as specified

Suupy and fixings in repairs 40 mm bore 600mm long GI spout for draining the surplus water from the sunken portion including cutting hole and making good the distrubed surface in cement mortar(1:3) or PCC 1:2:4 complete all as specified and directed.

Material and labour PCC 1:4:8 Type D2 (using 20 mm graded crushed stone aggregate), as in mass concrete in sunken floor, complete all as specified and directed.

Material and labour 40mm thick PCC 1: 2: 4 type B-1, (using 20mm graded crushed stone aggregate) as in floor & finishing the surface even & smooth using extra cement complete all as specified and directed.

S&F glass dividing strips 3mm thick and 38mm wide inserted in position conform to design complete all as specified and directed.

Dismantling floor, hearth wall tiling incld cement mortar bedding removing servicable tiles to store & rubbish off the premises. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

M&L for glazed ceramic coloured wall tiles 450x300x7mm thick on vertical surfaces such as dados set and jointed in neat cement slurry and pointed in white or coloured cement to match shade of tiles over and including 10 mm thick backing coat in CM(1:4) complete all as directed by Engr-in-Charge.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, in floors, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 15mm thick screed bed or bedding layer in CM(1:6) as specified and directed.

Material and labour non-skid, ceramic, coloured tiles 7 to 8mm thick (Square/rectangular ) area of each tile exceeding 0.11 sqm but not exceeding 0.18 sqm, as in skirting, set and jointed in cement slurry and pointed in white or coloured cement to match with the shade of tiles laid over and including 10mm thick backing coat on fair faces of brick work or concrete surface in CM(1:4) complete all as specified and directed.

M&L for vitrified light shade ceramic tiles 10 mm thick polished, area of each tiles not exceeding 0.36 sqm, in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over and including 15 mm thick screed bed in CM (1:6) complete all as directed by Engr-in-Charge.

All as per item no 20 here-in-before but in skirting and over 10mm cement backing in CM 1:4.

Dismantling of stone slab and tiles of any descriptoin or thickness in floors aprons etc, laid bedded and pointed in any mortar complete all as specified and directed.

Material and labour 18 to 20 mm thick granite (of any type) work (table rubbed and polished) in steps, landings, window cills cooking plate form and like in cement moryar (1:4) including pointing in white cement (1:2) using marble duet with admixture of pigment to match with shade of granite laid over and including 15mm thick screed bed or bedding layer in cm 1:6, and incliding rounding of edges of granite slabs 10 to 20 mm thick by grainding and rubbing and finished smooth, coloured as approved by GE all as specified and directed. Note: Front facia edges of granite slabs shall be rounding and finished smooth. The contractor shall quote his rates considering the above element, no extra paid on this.

All as per description of serial Item no. 23.00 here in before but as on vertical surfaces and over 10 mm thick rendering in CM 1:4.

Taking down cement plaster on brick or stone walls/ceiling etc including racking out joints, hacking for key, scrubbing down with water etc, complete all as specified and as directed. Note :- The demolished material should be disposed off outside MoD land. The contractor shall quote his rates considering the above element, no extra paid on this.

Demolition of brick or stone masonary built in cement morter incl all quions, arches, pillar etc. complete all as specified & directed.

Material and labour brick work with sub class -B bricks old size, straight or curved on planexc 6m mean radius built in CM (1:6). complete all as specified & directed.

All as per description of serial Item no. 27.00 here in before but as in half brick thick wall built in CM(1:4).

Material and labour 15mm thick rendering on other than faces of brick work or concrete surface in CM(1:6) to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour 10mm thick rendering on concrete surface in CM(1:3) as in ceiling surface to be finished even and smooth without using extra cement complete all as specified and directed..

Material and labour 15mm thick rendering on fair faces of brick work or concrete surface in CM(1:4) to be finished even and smooth without using extra cement complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces and applying three coats of white wash wall ,complete all as specified and directed.

Material and labour for preparation of newly plastered wall surface and applying two coats of oil bound distemper emulsion over and including a coat of primer, complete all as specified and directed.

Material and labour for preparation of newly plastered surfaces on ceiling and applying three coats of white wash on ceiling,complete all as specified and directed.

M & L for preparation of newly plastered surface of wall and applying two coats of acrylic emulsion exterior paint over and including a coat of primer, tint as approved by GE in camoflauge pattern, complete all as specified and directed.

Material and labour preparation of old decorated surfaces of walls including brooming down or steel wire brushing,scrapping down smoke soot, moulds, moss and efflorescent salts and trading oil and greasy spots as required and applying a coat of white lime wash, complete all as specified and as directed.

All as item No 36 above but as in ceiling.

Material and labour preparation of old decorated surfaces of walls by brooming down with steel wire brushing scrapping down smoke soot moulds moss and efflorescence salts and trading oil and greasy spot including washing, rubbing down and stopping the connected previously treated surfaces and applying one coat of oil bound distemper emulsion, complete all as specified and as directed.

Taking down chowkats or frames but with shutters (i.e. without taking off shutter from the frames) area not exc 1.5 sqm each, complete all as specified and directed.

Taking down chowkats or frames but with shutters (i.e. without taking off shutter from the frames) area Exc 1.5 sqm but n. exc 4 sqm each, complete all as specified and directed.

Taking down shutters of any description of area exc 1sqm but n. exc 2 sqm each complete all as specified and directed.

Supplying & fixing factory made 1.25 mm thick Pressed Steel door frame of size 105x60mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC 1:3:6 type C-0 using 12.5 mm graded stone aggregate, complete all as specified and directed by engineer-in-charge.

Supplying & fixing 1.25 mm thick Pressed Steel door frame of size 125x60mm for double doors with one or more rebates inclding necessary fixing lugs, hinges, lock strike plate, etc including filling back hollow with PCC(1:3:6) type C-0 using 12.5 mm graded stone aggregate, complete all as specified and directed by engineer-in-charge.

S&F Mild steel framed work as in door / cup board frames etc including necessary cutting, welding,drillings holes and fixed in position, all as specified and directed.

Supplying & fixing solid PVC door frame of sizes 50mm x 47mm made out of 5mm single side prelam PVC sheet used instead of plain colour PVC sheet & edges will be painted to match with prelam sheet reinforced with MS Square tube complete all specified and as directed.

S & F factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of M.S. tubes for top and bottom rails. M.S. frame shall be covered with heat moulded prelam PVC "C" channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for stiles and prelam colour PVC sheets for top rail , lock rail and bottom rail on either side and as gap insert for top rail and bottom rail , both side prelam PVC sheet used insted of plain colour PVC sheet. Stile and rail feathered at edges paneling of prelam solid sheets 10 mm thick to be fitted in the MS framewelded, sealed to the stiles and rails with suitable PVC sheet beading , and jointed together with solvent cement complete all as specified in SSR Part -II.

M & L for providing cupboard shutter in required size at site made out of 18 mm thk PVC colour sheet and provision of shutters one side decorative pre laminated PVC sheet and all required brackets SS screws etc. The pannels shall be fabricated using adhesive and screws where required. All the edges shall be covered with 2 mm thk edge bonding tape or 90 degree edge bent finish as per make and specification mentioned as per draeing and specification approved by Engr-in-charge.

S & F factory made Glazed & Skeleton shutters 35mm thick open rebated & prepare to received glass, gauge etc (without sash bars),edges of framing plain,chamfered or rounded, fitted with cut and mitred beads for securing glass, etc, size of member of shutters as as specified in SSR part-I, section 8 clause 8.24(a);supplied and fitted to chowkats, complete all as specified and directed by engineer-in-charge.

S&F factory made, 35 mm thick 2nd class hardwood, Plain, framed, panelled shutters (any number of panels), with panels of 12 mm BWP commercial ply with commercial veneering on both facessize of member of shutters as as specified in SSR part-I, section 8 clause 8.24(a);supplied and fitted to chowkats, complete all as specified and directed by engineer-in-charge.

S&F factory made box type steel window 1.25mm thick ERW hollow P section of each frame size 60mmx25mm including grill using 10 sqmm bar double rebated both guage and glass shutter comprised gaused glazed & Skelton shutter ERW section 50mmx20mm & 1mm thick with two openable leaf consisting of two number sash bars of T-Section 20mmx3mm complete welded to frame with one vertical mullion of ERW box type T-Section of size 60mmx25mm and 1.25mm thick with following fittings welded to the frame shutter :- i) Hold fast 150mm long mild steel flat iron 12x3 mm made to shape- 04 Nos per window. ii) Handle of Z section 20mmx25mm, 100mm long – 01 No per leaf. iii) MS tower bolt 150mm long 2 No per leaf. iv) Z section 20mmx25mm, 100mm long stopper – 01 Nos per leaf. v) Cleat 55 mm long of solid square 15x20x.63mm square - 01 Nos per leaf vi) MS pintal hinges 12 x 75 mm - 2 Nos each leaf vii) 10 mm squre guard bar @ 10 cm c/c

viii) 25 x 3 mm flat iron for joint of both frame wiremesh & Glazed welded inner side and outer side of frame (ix) 0.36 mm nominal dia of stainless steel wire mesh and average width of aperture 1.40 mm fixed in glazed/gazed skelton shutterof window (x) 3mm thick sheet glass ordinary quality and with oil putty in squre n exc 0.50 sqm in each pane fixed in glazed /guage skelton shutter of window xi) Fabrication and fixing arrangements as per specification including taking down, cutting holes and making good dismantled portion in PCC 1:2:4 type B-1 /cement plaster 1:4 as require and make finish good to the existing surface complete all as specified and directed. xii) Two coat of synthetic enamel paint over one shop coat of red oxide primer. Note: (i) Windows shall be povided as per the TD of Chief Engineer Chandigarh Zone, TD-219 i.e typical details of Box window (Steel) with fly proof shutter. (ii) The mode of measurement shall be only one for the set of two i.e wire mesh window and glass window at one location and nothing extra shall be measured on this account.

S & F mild steel box type ventilator fixed type with glazing bar with mesh & glass all as per item ser No 50.01-50.02 above.

Material and labour for preparation of new wood surfaces not other describe over 10cm width or girth and applying two coats of synthetic enamel paint over and including a coat of pink primer, complete all as specified and as directed.

Taking down shutters of any description exc 1sqm but n. exc 2 sqm from chowkat and re-fixing in same or different opeing after re-securing or easening and adjusting including minor repair complete all as specified.

Supply and fixing butt hinges extruded aluminium alloy with galvanised mild steel hinge pin, anodised and fixed, type B-22 100mm, ISI marked, fixing with stainless steel screws,complete all as specified and directed.

Supply and fixing 200 mm long aluminium anodised, barrel tower bolt of extruded section,fixed with stainless steel screws, complete all as specified and directed.

S&F in repairs Mild steel handle for Steel window of size 150mm length fixed with nut and bolts or screw suitable with existing provisions, complete all as specified and directed.

Supply and fixing in repairs Mild steel peg stay size 250mm length fixed to Steel window with nut and bolts or screw suitable with existing provisions, complete all as specified and directed.

Supply and fixing 150 mm size extruded aluminium alloy handels, fabricated type, anodised of pattern/design as approved, fixed with stainless steel screws, complete all as specified and directed.

Supply and fixing 300mm aluminium alloy, anodised, sliding door bolt with hasp staple (bolt type) fixing clips of sheet, cast or extruded setions and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed with stainless steel nut,bolt, complete all as specified and directed.

S&F Ball magnetic catcher with 8mm dia steel ball, brass body and striking plate including letting in and fixed, complete all as specified and directed.

Supply and fixing in repair 150mm long Hasp and staple stainless steel, saftey type, including bolt to hinge plate and fixed with fixed with stainless steel screws complete all as specified and directed.

Supply and fixing in stainless steel wirecloths 0.36 mm nominal dia of wire and average width aperature 1.40mm and fixed with stainless wire staples complete all as specified and directed..

All as per serial Item no. 62.00 here in before but Fixed-in- repairs.

S&F-in-repair wooden beads from skeleton doors, shutters with suitable nails, complete all as specified and directed..

Supply and fixing 140mm long floor door stoper of aluminium alloy body and toungue, anodised with hard drawn steel spring,fixed to door shutter fixed with stainless steel screws complete all as specified and directed.

All as per serial Item no. 65.00 here in before but Fixed-in -repairs.

S&F 3.0mm thick sheet glass ordinary quality and glazing with oil putty in square n exc 0.50 Sqm in each panes and Hacking out old broken glass (any thickness size quality or description) from wooden frames or stone, concrete or brick surrounds glazing with putty or fixed with beads complete all as specified and directed.

S&F in repairs heavy duty Stainless steel (Grade 305) curtain rods of 25mm dia, complete all as specified and as directed.

S&F in repairs Stainless steel (Grade 305) brackets (Open ends) suitable for curtain rods of 25mm dia, complete all as specified and as directed.

S&F in repairs Stainless steel (Grade 305) brackets (Dead ends) suitable for curtain rods of 25mm dia, complete all as specified and as directed.

S&F mild steel 300mm, ordinary rat tail rod pattern springs, including roller and roller plate, complete all as specified and directed.

All as per serial Item no.71.00 here in before but fixed-in-repairs.

M&L for Taking up or down 15 mm dia steel tubing & connections and removal , complete all as specified and as directed.

All as per serial Item no.73.00 here in before but 20mm bore tubes.

S & F 15mm bore, medium grade galvanized steel tube with screwed socket joints, together with all tube fittings, fixed complete to walls & ceiling or laid in floors complete all as specified and directed.

All as per Item No 75 but pipe dia 20 mm.

Fixing only 15 mm bore pipe, after cleaning the pipe with all new tube fittings , complete all as specified and as directed.

All as per description of serial Item no. 76.00 here in before but 20mm bore tubes.

Dismantling water tanks any type of capacity and removal from site, complete all as specified and as directed.

S&F 500 liter capacity Rotational moulded polyethylene water storage tanks (cylindrical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 1000 liter capacity Rotational moulded polyethylene water storage tanks (cylin-drical vertical with closed top) tripple layered white, hoisted and fixed in position, including 20 mm bore Ball valves high pressure of PTMT with epoxy coated aluminium rod and high density plastic ball screwed for iron pipe complete all as specified and directed.

S&F 20mm PTMT nipple suitable for HDPE water tank (minimum weight 45gms) complete all as specified .

S&F in repair PVC (PTMT) float valve, high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipe and fixed suitable for 20mm bore pipe, complete all as secified and directed

S & F in repair long body stop valve 15mm bore fancy type, chromium plated, screwed down, high pressure, with quarter turn, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&F in repair 15mm bore long body Angle cock, fancy type, chromium plated, screwed down, high pressure, with quarter turn, screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S & F in repair long body stop valve, 15mm bore fancy type, chromium plated with long shank and cup (concealed type) screwed down high pressure, with crutch or butterfly handle screwed both ends for iron pipe or for unions, complete all as specified and as directed.

S&F in repair 15mm long body bib taps long shank cast copper alloy with crutch quarter turns, secrwed for iron piper or for brass ferrule, complete all as specified and as directed.

S&F in repair Pillar taps long body fancy type with capasten head chromium plated screwed down high pressure with without lettered 'Hot' or Cold with long screwed shanks and fly nuts screwed for iron pipe and fixed , complete all as specified and as directed.

S&F in repairs 15mm bore PVC connection pipe 450mm long with PTMT nuts at both ends, complete all as specified and as directed.

S &F-in-repair chromium plated brass shower rose, 125mm size with or without swivel joints, with shower arm 15mm size 195 mm long with bend of 45degree, fixing to 15 mm bore steel pipe or union , complete all as specified and as directed.

S & F in repair towel rail chromium plated brass, 20mm dia 600mm long, including brackets, screws and wooden/plastic cleats, complete all as specified and as directed.

S&F in repairs 100 mm dia Stainless steel grating complete all as specified.

S&F in repairs 75 mm dia Stainless steel with hole grating complete all as specified.

S&F in repairs waste down pipe 32/40mm bore for wash basin/sink complete all as specified and directed

S& F in repair vitreous china squatting pan, Orissa pattern, size 580 x 440mm white, with integral foot rests( excluding flushing cistern and flush pipe) but including traps,complete all as specified and directed

S & F in repair 10 Ltr capacity PVC valveless syphonic action type flushing cistern low level white with inlet ball valve and brackets, float and handle, L-Bend complete all as specified and directed

S&F in repairs vitreous china wash basin, white, flat back, size 580x450mm excluding taps waste, chain and plug and porcelain stopper but including bracket complete all as specified and directed

Demolition up to 100/75mm bore and breaking up drain pipes (AC/reinforced concrete/salt glazed ) complete all as specified and directed.

S & F 110mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F 75mm bore PVC SWR Pipes single socketed, in any length with rubber ring joints, fixed to walls complete all as specified and directed.

S & F 110mm bore PVC SWR Junction single (Single T) equal or unequal complete all as specified and directed.

S&F PVC (SWR) bend of 110 mm bore complete all as specified and directed

S&F PVC (SWR) bend of 110 mm bore with access door complete all as specified and directed

S&F PVC (SWR) 110mm bore Junction (single T) equal or unequal complete all as specified and directed

S&F PVC (SWR) bend of 75 mm bore complete all as specified and directed

S&F PVC (SWR) bend of 75 mm bore with access door complete all as specified and directed

S&F PVC (SWR) bend of 110 mm reducers complete all as specified and directed

S&F PVC (SWR) bend of 75 vent cowl with access door complete all as specified and directed

S & F in repair 75mm bore PVC (SWR) floor trap,with grating plain/ whole including jointing to waste pipe fixed in cement concrete type B-1 (1:2:4) complete all as specified and directed.

S&F as in repair stainless steel plate rack, made out of 0.80mm thick of size 31"x36"x10" , of pattern as approved, complete all as specified and directed.

S&F in repair sinks made of stainless steel 1mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar on to dwarf wall or including fixing cantilever brackets and connecting union to pipe overall size 495mmx420mm bowl size 410mmx330mmx160mm complete all as specified and directed

S&F in repair stainless steel 32mm waste coupling suitable for stainless steel sink along with grating complete all as specified and directed by Engr-In-Charge.

M&L for white cementing to joints WC and floor traps,in bath room or Kitchen and floor traps including removing of grating & re-fixing after application of white cement on inner surface etc, complete all as specified and directerd.

Taking down aluminium shutter / sliding door for necessary repair work and re-fixing in position after adjusting or re securing with steel strip with replacement of steel screw re threading and fixing on existing devices, resetting or replacing top pivots bottom steel plates etc and replacing glazing etc for proper functioning of aluminum door of area n exc 1.5 sqm each complete all as specified. Note :- Supply only glazing and top pivots etc shall be measured and paid seperately.

Supply only 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads, clips etc complete all as specified and directed. Note: Cost of rubber beads, clip included in unit quoted rate of this item.

S & F as in repairs mild steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) work for frame of doors, windows,ventilators and partitions (Fixedportions) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws, all complete as diercted by engineer-in-charge.

Providing and fixing Powder coated aluminium (minimum thickness of powder coating 50 micron) for shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber/ neoprene gasket required (Fittings shall be paid for separately) with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS:1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing/ paneling, C.P. brass/ stainless steel screws all complete as directed by engineer-in-charge.

S & F double action floor door spring hydraulically regulated made up minimum 1.25 thick aluminium alloy sheet foundation box, main body stainless steel cover, governing pivot made of brass, other parts made of mild steel heavy duty complete all as specified

S & F top pivot of casting body suitable for aluminum door, complete all as specified and directed.

Supply and fixing 170 to 200 mm size extruded aluminium alloy handels fabricated fancy type, anodised fixed with stainless steel screws complete all as specified and directed.

Supply and fixing 200mm long aluminium anodised barrel tower bolt, extruded section,fixed with stainless steel screws complete all as specified and directed.

S & F 4 mm thick high quality, durable acrylic panel sheet and glazing with rubber beads, clips etc complete all as specified and directed. Note: Cost of rubber beads, clip included in unit quoted rate of this item.

S & F 4.80 mm thick sheet glass of ordinary quality plain / tinted and glazing with rubber beads, clips etc complete all as specified and directed. Note: Cost of rubber beads, clip included in unit quoted rate of this item.

S & F steel mortice lock vertical type 100mm, 4 levers all as specified complete all as specified and directed.

Durga Construction Company (BID ID -3390945)

Beenu Co. Company (BID ID -3399491)

m/s gaurav enterprises (BID ID -3391471)

HINGLAZ ENTERPRISES (BID ID -3398184)