REPAIR TO FLOORING PLASTERING JOINERY SAINTARY FITTINGS PLUMBING ETC IN WSA III AND PROVN OF SOAK PIT NEAR IFS AT AF STN ADAMPUR

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in SOFT/LOOSE soil complete, all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in SOFT/LOOSE soil complete, all as specified and directed.

Removing excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified.

M&L for Reinforced cement concrete (1:2:4) type B-0 (nominal mix) using 20mm graded crushed stone aggregates as in as in shelves / cooking platform and the like including necessary form work etc complete all as specified and directed.

M&L for PCC type C-2 (1:3:6), using 40 mm graded crushed stone aggregates as in walls or retaining walls, any thickness, size or shape including pilasters, buttresses columns pillars, boundary pillars and posts (including caps and bases) complete all as specified and directed.

M&L for PCC type C-2 (1:3:6), using 40 mm graded crushed stone aggregates as in surface channels & drains etc. complete all as specified and directed.

M&L for PCC type D-2 (1:4:8), using 40 mm graded crushed stone aggregates as in foundation filling & mass concrete, complete all as specified and directed.

M&L for Plain Cement concrete (1:2:4) type B-1 using 20mm graded crushed stone aggregate as in coping,weathering, slightly rounded or chamfered angles and throating complete all as specified and directed.

Precast reinforced cement concrete (1:2:4) type B-1 using 20mm graded stone aggregate as in manhole / drain covers with 40mm dia holes in the slabs to run off and the like duly placed on manholes with cement mortar (1:4) complete.

M&L for Cement concrete (1:2:4) type B-0 using 12.5mm graded stone aggregate as in lintels upto 1.5 mtr clear span, cills, steps , coping including necessary form work etc complete all as specified.

Supply only water proofing compound, ISI marked, complete all as specified and directed.

M&L for Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified and directed.

M&L for Brick work using old size bricks (EXCEPT BRICKS), straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:4), complete all as specified and directed.

M&L for Cutting openings, through brick walls, built in cement mortar for door, window & other openings or enlarging existing openings, converting window into door openings, etc. or cutting out defective bk wk for under-pinning, including providing, fixing & removing shoring, cleaning & stacking bricks, removing surplus serviceable bricks, hardcore, etc., to store & rubbish not exc. 50 m, complete all as specified and directed.

M&L for Solid PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing on PVC frame complete all as specified and directed.

M&L for 5 mm thick PVC sheet fillet of width 35 mm for wall paneling inclusive of fixing on to wall to make PVC frame, complete all as specified and directed.

M&L for Powder coated GI snap grid frame work including suspenders with size of grid 605 mm x 605 mm for false ceiling all as specified and shown on serial page No. 186 of MES Schedule Part-II.

M&L for 4 mm thick asbestos fibre cement building board, cut to size and fixed in grid frame work ceiling as panels, complete all as specified and directed.

M&L for Factory made, 35 mm thick, second class hard wood, plain framed, hammer marked, panelled shutter (two panel) with lock rail and panel of 9 mm B.W.P. commercial ply or veneered particle board with commercial veneering on both faces. The size of rail and stile as per IS : 1003 (Part I), kiln seasoned and chemically pressure treated complete all as specified and directed.

S&F factory made solid PVC moulded Door shutter, 28 to 30 mm thick (stiles) with 2,4 or 6 raised panel design with 2mm thick moulded prelam PVC sheet on the front face & 2mm prelam PVC sheet on back face, supplying and fixing at site as per specification and drawing complete all all as specified and directed.

S&F, Factory made solid panel PVC door shutter 30mm thick (style) consisting of frame made out of MS tubes for top and bottom rails, MS frame shall be covered with heat moulded plain colour PVC 'C' channel having a PVC sheet strip of 20mm width stuck inside with solvent cement for styles and plain colour PVC sheet for top rail, lock rail and bottom rail, panelling of plain colour PVC sheet to be fitted in the MS frame welded / sealed to the stile and rails with suitable PVC sheet beading and jointed together with solvent cement as specified in SSR Part II, complete all as specified and directed.

S&F, Factory made solid PVC Door frame of size 50mm x 47mm made out of 5mm thick plain colour PVC sheet reinforced with mild steel square tube, suppling & fixing in opening, complete all as specified and directed.

M&L for 9mm thick pre laminated particle board, interior grade, prelaminated one side with decorative choice lamination & other side balancing white lamination, fixed with screws to framework complete all as specified and as directed.

S&F, 04 levers brass mortice lock, vertical type, 100 mm size, with 2-3 keys, IN REPAIRS, complete all as specified.

S&F, Aluminium (Die cast) door closer hydraulically regulated designation No. 3 aluminium body universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg, ISI marked, complete all as specified.

S&F, Double action floor door spring, hydraulically regulated, made of 1.25 mm thick aluminium alloy sheet, foundation box main body with stainless steel cover, governing pivot made of brass, rest of part made out of heavy duty mild steel, ISI marked, complete all as specified and directed.

S&F, Aluminium anodised barrel tower bolt of extruded section 150 mm long, ISI marked, complete all as specified and directed.

S&F, Aluminium anodised barrel tower bolt of extruded section 200 mm long, ISI marked, complete all as specified and directed.

S&F, Aluminium alloy, anodised, ISI marked sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet, cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long, complete all as specified and directed.

S&F, Stainless steel sliding door bolt with hasp and staple (bolt type) and fixing round typeclips of sheet , cast or extruded sections and fixing bolts and sliding bolts of extruded section or cast aluminium alloy 250 mm long complete all as specified and directed. MAKE: PRAYAG CAT NO. SLD-1210 or equivalent make mentioned in Appndix 'B'

S&F, Stainless steel 100mm long butt hinges with stainless steel screws, ISI marked complete all as specified and directed. MAKE: PRAYAG CAT HG-3414 or equivalent make mentioned in Appendix 'B'

S&F, Extruded aluminium anodised handles 125 mm long fabricated type with plate , ISI marked complete all as specified and directed.

S&F, Double leg aluminium anodised door stopper with rubber foot 150 mm long, ISI marked and fixed to bottom rail of doors with steel screws, complete all as specified and directed.

M&L for Stainless steel wire cloth 0.36 mm nominal dia of wire and average width of aperature 1.40 mm and fixed with tinned tacks or steel wire staples, all as specified.

M&L for mild steel PVC powder coated (Coloured) curtain rod with fixing side brackets, end cups and fixed with PVC rawl plugs & steel screws as in repairs complete all as specified and directed

M&L for Powder coated aluminium frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

M&L for Powder coated aluminium door shutters with styles & rails made out of section size 83-85 mm x 44-45 mm (wall thickness not less than 2 mm) , anodised alumnium glazing snap beading (having wall thickness not less than 0.90 mm), rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified. NOTES: (a) Each shutter shall have 2 Nos. 200 mm long almn handles and 03 No. 100 mm size stainless steel/almn butt hinges. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ. (c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron.

M&L for Powder coated aluminium window and ventilator shutters side hung type with styles & rails made out of section size 47-48 mm x 44-45 mm (wall thickness not less than 1.58 mm), anodised alumnium glazing snap beading (having wall thickness not less than 0.90 mm), rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified. NOTES: (a) Each shutter shall have 2 Nos. 125 mm long almn handles and 02 No. 75 mm size stainless steel/almn butt hinges & one no. almn hook & eye. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ. (c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron.

Powder coated aluminium grill type DG-117 including necessary 'U' clip & screws etc as per manufacturers instructions, complete all as specified.

S&F, Sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5 Sq.m in each pane complete all as specified and directed.

S&F, Sheet glass 5.5mm thick ordinary quality and glazing with oil putty or wooden beads in squares exc. 0.5 Sq.m in each pane complete all as specified and directed.

M&L for Mild steel TMT bars 10mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for columns, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9mm dia or securing with clips complete all as specified.

S&F, Mild steel works in hand rails, half round or other stock section or core for wooden handrail straight portion, drilled and countersunk for balusters running bars, for doors, balusters, nosing to steps including embeding in concrete and screwing etc. wind ties for roof including securing bolts; posts and struts in fencing including cutting tops to shape as directed, drilling holes, notching for wire, etc.; flat iron fillets (for securing wire mesh etc.) in-cluding all necessary drilling, bolting or riveting, etc., confirming to Fe-290-Gde E-165, complete all as specified and directed.

S&F, 2mm thick fibre glass reinforced translucent plain sheeting with two corrugations side lap fixed with coach srew and washer in roof , wall etc., complete.

S&F, Framed mild steel work such as grills, grating etc. with ends of bars shouldered and or riveted or forged into spikes, framed guard bars, railings and similar work confirming to Fe-290-Gde E-165, complete all as specified and directed.

Fixing only chain link fencing including line wire mesh, any mesh, size and type to any types of standards rails, straining bolts, mild steel round bars etc. including provision of binding wire complete, all as specified and directed.

Supply only chain link mild steel galvanised hot dipped fencing (mesh of 10 gauge wire and weight exc. 3.00 kg/Sq.m) complete all as specified and directed. NOTE:- The weight of chain link fencing shall be ascertained by BOO as ordered by GE and payment shall be made acoordingly.

Supply only Mild steel screw bolts (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, exc 5 cm but not exceeding 10 cm long, dia of neck 5 to 10 mm, complete all as specified and directed.

Supply only Mild steel round bars 10mm dia and over, cut to length, bent to shape required, for chain link fencing complete, all as specified and directed.

S&F, Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed, IN REPAIRS, (each line wire to be measured) complete all as specified and directed.

S&F, framed work as in doors or gates of angle or other section with gusset plates, rails, braces etc. complete drilled for fixing of steel sheeting or other covering doors etc. to be prepared for hanging or sliding with and including either hooks and hinges or steel hanging door fittings (exclusive of steel sheeting or other covering, running rails and guides) and hanging also fastening and fixing complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 105 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete all as specified and directed.

S&F, Factory made pre painted pressed steel frames, conforming to IS, having profile 125 mm x 60 mm for doors with one or more rebates made out of 1.25 mm thick mild steel sheet, including necessary fixing lugs, butt hinges, lock strike plate, etc., duly filled with PCC(1:3:6) type C-0 complete all as specified and directed.

S&F, Factory made steel windows with side hung shutter with glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete all as specified and directed.

S&F, Factory made steel windows with side hung shutter without glazng bars each shutter having 02 No. box type hinges & two nos. tower bolts of size not less than 150 mm size and peg stays, dovetailed or welded,complete all as specified and directed.

S&F, Steel windows or ventilators, fixed type made of MS sheet 1.25 mm thick box type (primer coated), ERW hollow 'P' section of size 60mm x 25 mm complete all as specified and directed. NOTES: (a) Profile section used under these items shall be 'P' tube as shown in drawing No. CE/AF/STD-170/07, CE/AF/STD-171/07 and CE/AF/STD-172/07 as applicable.

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, Pre-painted galvalume aluminium zinc coating GI based Plain steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

S&F, Pre-painted galvalume aluminium zinc coating GI based corrugated steel (Except sheeting) 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws complete all as specified and directed.

M&L for 75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate, finished even & smooth without using extra cement, as in plinth protection, and joints shall be sealed with joint sealing comound grade 'A' complete all as specified and directed.

M&L for 75 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for 75 mm thick, cement concrete type D-2, 1:2:4 using 40 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for 100 mm thick, cement concrete type D-2, 1:4:8 using 40 mm graded crushed stone aggregate, finished even & rough, as in sub floors, complete all as specified and directed.

M&L for Glazed ceramic coloured tiles 7mm thick, area of each tile exc. 0.17 Sq.m but n. exc. 0.19 Sq.m on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for First quality, vitrified ceramic tiles 9-10mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, on vertical surfaces as in skirting, dado etc. set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 10 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Non skid ceramic coloured tiles 7 to 8mm thick (square/ rectangular) area of each tile exc. 0.18 Sq.m but n. exc. 0.38 Sq.m, laid in floors etc, set and jointed in neat cement slurry and pointed with grout of matching shade of tiles, laid over and including 15 mm thick bedding layer in cement mortar (1:4), complete all as specified and directed.

M&L for Granite jet black shade, 15-18 mm thick,as in step, jambs, cooking platform and like, machine cut, machine polished, bedded and jointed with grey cement slurry & pointed with grout of matching shade including necessary cutting over & including 10 mm thick (average thickness) cement mortar (1:4), complete all as specified and directed.

M&L for Rounding of / moulding to edges (half round) of stone of any description including rubbing and polishing (Granite finish), complete all as specified and directed.

M&L for Machine cut Kota stone slab flooring 16-18 mm thick, area of each slab not less than 0.30 sq.m, (cut to size in square shape) laid in floors over & including 20 mm thick (average thickness) cement mortar (1:4) screed and jointed with grey cement slurry mixed with matching shade pigment including rubbing and polishing (Granite finish) complete, all as specified.

M&L for Kota stone slab 16-18 cm thick on vertical surfaces like riser of steps, skirting, dado and pillar laid over & including 10 mm thick (average thickness) cement mortar (1:4) and jointed with grey cement slurry mixed with pigment to match the shade of the slab including rubbing and polishing (Granite finish), complete all as specified and directed.

M&L for 60mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 25mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for 80mm thick factory made chamfered edge cement concrete paver block of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 25mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete all as specified and directed.

M&L for Rendering 5 mm thick on fair faces of concrete surfaces, finished fair and even on ceiling surfaces in cement mortar (1:3), complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:6) complete all as specified and directed.

M&L for Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), mixed with or without water proofing compound as per manufacturers instructions, complete all as specified and directed. NOTE:- WPC measured & paid separately under respective item.

M&L for Two coat of whitewsh on old ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Two coat of interior acrylic distemper/oil bound distemper on new ceiling surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for One coat of interior acrylic distemper/oil bound distemper on old wall surfaces, including preparation of surfaces, complete all as specified and directed.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and directed and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper/oil bound distemper over and including a coat of interior primer.

M&L for Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces as specified. (preparatory to paint as directed). (b) Two coats of interior acrylic distemper over and including a coat of acrylic emulsion primer.

M&L for Prepration of new plasterd wall surfaces of any description complete all as specified and applying the following: - (a) Applying wall care putty, in two coats & smoothening the surfaces with sand papers/ mechanized sanding etc., (preparatory to paint as directed). (b) Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer in four/six shades of disruptive/camouflaging pattern for height not exceeding 8.5 metre complete all as specified and directed.

M&L for Two coats of exterior acrylic emulsion over a coat of exterior (water based) primer on old wall surfaces, in disruptive/camouflaging pattern of four shades including preparation of surfaces, for height not exceeding 8.5 metre, complete all as specified and directed.

NOTE FOR SERIAL ITEM NO. 78 TO 83 (i) Entire quantity of material for this work shall be procured by the contractor from manufacturer's Depot & deposit the same with Enginer-in-Charge and same shall be issued to contractor on daily basis as per consumption at site. (ii) The work shall be got executed through paint manufacturer/ authorised applicators of manufacturer's as specified in relevent PS clause. (iii) RGB value of four shades of disruptive/camouflaging pattern shall be all as shown on Drg No. GE/SK-1/19 sheet 1/2 & 2/2.

S&F, Sheet glass 4mm thick ordinary quality and glazing with oil putty or wooden beads in squares n. exc. 0.5 Sq.m in each pane complete all as specified and directed.

S&F, Figured glass pin head type 4 mm thick, and glazing with oil putty or wooden beads in squares n. exc. 0.5sqm in each pane complete all as specified and directed.

M&L for Applying one coat (finishing coat) of synthetic enamel paint, including preparation of old painted wood and wood based surfaces of any description not other wise described over 10cm width or girth and complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of pink primer over wood and wood based surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over old steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including complete removal of existing surfaces complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over new steel & iron surfaces of any description, not otherwise described, over 10 cm in width or girth, including preparation of surfaces complete all as specified and directed.

M&L for Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel & iron surfaces of any description n exc 10cm width or girth when unconnected with other painting or when painted in different tint including preparation of surfaces complete, all as specified and directed.

S&F, Steel tubes 15 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F, Steel tubes 20 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F, Steel tubes 25 mm bore ‘medium grade’, galvanized with all fittings and fixed to walls and ceilings or laid in floors, complete all as specified and directed.

S&F, 500 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN-REPAIRS, complete all as specified including the following acessories: - (i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, IN REPAIRS, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

S&F, 1000 litre capacity, white, three layered polyethylene water storage tanks (cylindrical vertical with threaded lid) including hoisted and fixed in position, making connections, IN-REPAIRS, complete all as specified including the following acessories: - (i) PTMT ball valves, high pressure, with epoxy coated aluminium rod & high density plastic ball complete screwed for iron pipe or brass ferrule and fixed, suitable for 20 mm bore GI pipe, IN REPAIRS, complete all as specified. (iii) Gun-metal stop valve (quarter turn type) with MS lever handle, suitable for GI tubes 20 mm bore, ISI marked, screwed both ends for iron pipe, IN REPAIRS, complete all as specified. (iv) Provn of 20 mm bore GI light grade tube from O/H tank to nearest mouth of RWP, IN REPAIRS, complete all as specified.

S&F, Angular stop valve/cock, cast copper alloy, chromium plated, with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. MAKE: PRAYAG Cat No. 6510 or equivalent make mentioned in Appendix 'B'.

S&F, Ball brass valve 20 mm bore, high pressure with polythene float and flynut complete screwed for iron pipe or brass IN REPLACEMENT all as specified and directed

S&F, Ball brass valve 25 mm bore, high pressure with polythene float and flynut complete screwed for iron pipe or brass IN REPLACEMENT all as specified and directed

S&F, Bib tap, cast copper alloy, chromium plated fancy type, long body with wall flange, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 6508 or equivalent make mentioned in Appendix 'B'.

S&F, Pillar tap, cast copper alloy, chromium plated fancy type, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete all as specified and directed. MAKE: KEROVIT Cat No.KB1211001 or equivalent make mentioned in Appendix 'B'.

Center hole basin mixer without pop up, cast copper alloy, chromium plated fancy type, quarter turn type, screwed end for iron pipe or for union and fixed, suitable for 15 mm bore pipe, IN REPAIRS, complete. MAKE: KEROVIT Cat No. KB1211026 or equivalent make mentioned in Appendix 'B'.

S&F, Overhead ABS shower with cast copper alloy chromium plated arm 225 mm long with flange and fixed in position, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat BS-76 or equivalent make mentioned in Appendix 'B'..

S&F, Brass chromium plated towel rail 500-600 mm long, fixed to wall with SS screws and PVC rawl plugs, complete. MAKE: PRAYAG Cat No. BA-10 or equivalent make mentioned in Appndix 'B'.

S&F, Glass shelf 500x125 mm with brass brackets and fixed to wall with chromium plated brass screws and rawl plugs, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-45 or equivalent make mentioned in Appendix 'B'.

S&F, Stainless steel round slotted grating with frame, 100-125 mm size fixed in position with cement joints, IN REPAIRS, complete all as specified and directed.

S&F, PVC connections with PTMT nuts, 600 mm long, IN REPAIRS, complete all as specified and directed.

S&F, Vitreous China half stall Urinal pot, white, size 345 x 320 x 560 mm, with & including cast copper alloy, half or full threaded chromium plated waste coupling suitable for & including 32 mm size PVC waste/discharge pipe, rag bolts, IN REPAIRS, complete. MAKE OF URINAL: PRAYAG Cat No. 4998 or equivalent make mentioned in Appendix 'B'.

S&F, Flush cock (lever type) 25 mm size for urinals complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-32 or equivalent make mentioned in Appendix 'B'.

S&F, Health faucet CP brass body with wall hook and 1 metre SS tube, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. BEA-97 or equivalent make mentioned in Appndix 'B'.

S&F, Toilet paper holder, brass chromium plated body IN REPAIRS, complete all as specified and directed MAKE OF EWC: PRAYAG Cat No. BA18 or equivalent make mentioned in Appendix 'B'.

S&F, PVC flushing cistern 10 litre capacity, syphonic action type, any shade, dual flush, ISI marked with flush pipe and all fixing acessories, IN REPAIRS, complete all as specified and directed. MAKE: PRAYAG Cat No. 502 or equivalent make mentioned in Appendix 'B'

S&F, Vitreous china wash down water closet pan (pedestal pattern), ISI marked, white with uPVC 'S' trap of size 540x365x390 mm, including seat cover and necessary SS Jet spray (L-bend) with 01 metre braded tube fixing acessories, IN REPAIR, complete all as specified and directed. MAKE: PRAYAG Cat No. 4016 or equivalent make mentioned in Appndix 'B'.

Vitreous China wash down water closet pan (One piece with cistern), white, ISI marked, with & including Health faust with 1 metre SS tube & hook with PP thin rim seat cover and necessary rag bolts, IN REPAIRS, complete all as specified. MAKE OF EWC: KEROVIT Cat No. KS709 or equivalent make mentioned in Appendix 'B'.

Stainless steel sink with drainage board made out of 1.00mm thick sheet for kitchen or laboratory with plug waste pipe washers including cantilever cast iron brackets connecting union etc overall size 940mm x 460mm x 203 mm with bowl size 354mmx 405mmx 203mm,IN REPLACEMENT complete all as specified and directed. MAKE:PRAYAG Cat No. 1342D or equivalent make mentioned in Appndix 'B'.

Maintenance of drain / Nallah (cross sectional area n exc 1.5 Sq.m) by cutting all bushes, shrubs, sarkandas and any type of vegetation and desilting all deposit of soil and other material to have a free flow of water and to get a uniform trapezoidal/ rectangular shape of drain and removing all spoil outside MOD area at authourised dumping site declared by local administration etc complete.

S&F, uPVC pipes 75 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with or without rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

S&F, uPVC pipes 110 mm external dia, type-B, ISI marked (IS:13592) single socketed in any length with or withou rubber ring joints, fixed under floors/walls as SWR pipes, IN REPAIRS, complete all as specified and directed.

S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 75 mm external dia, IN REPAIRS, complete all as specified and directed.

S&F, uPVC/PVC bend any radius, suitable for uPVC soil waste discharge pipes 110 mm external dia, IN REPAIRS, complete all as specified and directed.

S&F, uPVC floor trap, suitable for uPVC soil waste discharge pipes 75 mm ext dia, embedded in PCC type B-1(1:2:4), IN REPAIRS, complete all as specified and directed.

Construction of "SOAK WELL" of size 2.40 m dia & 3.0 metre effective depth complete all as specified and directed and shown on drawing No. CEJZ/STD-301/90 sheet 1/4 to 4/4.

DISMANLING/DEMOLITION WORKS :-

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area not exceeding 1.50 Sq.m each and removing from site all as specified and directed.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified and directed.

Taking down shutters of any description exceeding 1.00 sqm but not exceeding 2.00 sqm each and refixing in the same opening after easing adjusting and minor REPAIRS complete all as specified and directed.

Taking down cement or cement lime plaster, any description on brick or stone walls etc including raking out joints, hacking for key, scrubbing down with water etc, complete all as specified and directed.

Dismantling of Brickwork or stone/boulder masonry, built in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dressed stone-work and precast concrete articles complete all as specified and directed.

Demolition of cement concrete (unreinforced) in ground floors and pavings not excceding 15cm thickness (above or below ground level) complete all as specified and directed.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified and directed.

Taking up or down steel tubing 15 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 20 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Taking up or down steel tubing 25 mm bore and connections, including cleaning for re-fixing or removal to store complete all as specified and directed.

Dismantling barbed wire fencig, any type complete all as specified and directed.

Dismantling plain or corrugated steel sheeting, any gauge, thickness, including Nainital or similar pattern roof coverings, complete all as specified.

Dismantling wall and ceiling boards (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified and directed.

Demolition of stone slabs and tiles of any description or thickness in floors, aprons etc. laid, bedded and pointed in any mortar complete all as specified and as directed.

Dismantling posts or struts (wood, steel or R.C.C.) any section, including taking out embedded portion and making good disturbed ground, embedded with concrete etc. complete all as specified and directed.

NOTE : Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

siddharthenterprises (BID ID -3383956)