SPECIAL REPAIR TO CHAIN LINK FENCING AND BOUNDARY WALL OF OFFRS MD ACCN IN AOR OF B/R-II GE (WEST) JABALPUR

Excavating in post holes in soft/loose soil (or similar holes) each n exc 0.5 cu.m. getting out, returing, filling in and ramming earth or broken ruble mixed with earth around, in layers not exceeding 25 cm , watering, and removing surplus soil to a distance n exc 50 M and making good surface.

M&L for PCC (1:3:6) type C-2 using 40mm graded stone aggregate in foundation, filling & mass concrete all as specified.

Supply only for chain link fencing including line galvanised steel wire 3mm dia. Mesh Size 50 x 50mm etc complete.

Fixing only chain link fencing including line wire any mesh size and type to any type of stands, rails straning bolts etc inccluding provision of binding wire , nut bolts etc required for fixing

S&F mild steel works as in posts and struts in fencing including cutting tops to shape as directed drilling holes notching for wire fencing/chain link fencing etc flat iron fillets, sag rods (for securing chain link fencing etc) including all necessary drilling, bolting or reveting, welding etc and embeding in concrete and securing etc. and similar works conforming to Fe- 290, grade E-165. All as specified and directed

M&L for preparation of newly steel surfacces of any description not otherwise desribed, over 10cm width or girth and applying two coat of synthetic enamel paint over a coat of red-oxide zinc chrome primer surfaces complete all as specified and as directed.

S&F for galvanised 2 strand, steel barbed wire 2.24 mm dia barbed with 2 mm dia barbs at 75 mm spacing and straning and fixing to any type of standard rails straining bolts, including securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins etc as directed (each line to be measured).

S & F Mild steel screw bolts 5 to 10 mm dia (machine made) with hexagonal or square heads at one end and screwed the other, or screwed both ends, each screwed end to be fitted with washers and one hexagonal or square nut, n exc 5cm long

S & F GDE Fe410-W quality B Framed work as in ornamental type gates of angle or other section with gusset plates, rails, braces, etc., complete, drilled for fixing of steel sheeting or other covering. Doors, etc. to be prepared for hanging or sliding with and including either hooks and hin complete all as specified and as directed by Engineer-in-Charge.

S&F concertina coil of 600 mm dia of approved type/make for laying on y shape angle fixed on boundary wall etc completed all as specified and directed.

S&F, Galvanised, 2 strand, steel barbed wire 2.24mm dia barbed with 2mm dia barbs at 75mm spacings and straining and fixing to any type of standard rails straining bolts, including, securing or tying at crossings with and provision of galvanised mild steel wire, staples or steel pins, etc. as directed (each line wire to be measured) complete all as specified and directed.

Earth work in excavation by mechanical means (Hydraulic excavator)/ in foundation trenches or drains ( exceeding 1.5 m in width or 10 sqm on plan), including dressing of sides and ramming of bottoms, lift upto 2.5 m, including getting out the excavated soil and disposal of surplus excavated soil as directed, within a lead of 50 m

M&L for PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in foundation & mass concrete complete all as specified and directed.

M&L for Use and waste of formwork to sides of concrete foundations, footings, bases of columns, raft and raft beams, sides and soffits (if any) of foundation and plinth beams; and similar work; vertical or to batter complete all as specified and directed.

M&L for RCC design mix M-25 using 20mm graded stone aggregate in Foundations, including rafts, footings, foundation beams; plinth beams; bases for columns, etc.; basement slabs, under-reamed piles and mass concrete complete all as specified and directed.

M&L for Use and waste of formwork to sides of rough finished flat surface pillars, posts, struts, piers, columns and stanchions complete all as specified and directed.

M&L for RCC design mix M-25 using 20mm graded stone aggregate in Columns, pillars, piers, posts and struts complete all as specified and directed.

M&L for Use and waste of formwork to rough finished flat surface sides and soffits of floor or roof beams, beam haunchings, girders, bressummers, lintels, cantilevers, shelves including supports, overhangs, etc. also splays between floors and beams, etc. complete all as specified and directed.

M&L for fly ash brick work built in cm (1:6) of compressive strength not less than 75 Kg/Sqcm straight or curved on plan exceeding 6 mtr mean radius complete all as specified and directed.

M&L for RCC design mix M-25 using 20mm graded stone aggregate in Beams, cantilevers, bressummers, lintels over 1.5m span complete all as specified and directed.

M&L for Rendering 15 mm thick on brick work or concrete surface in two coat 1st coat 10 mm thick with CM 1:6 2nd coat with 5 mm thick cm 1:4 finished fair& even without using extra cement surface complete all as specified and directed.

M&L for TMT HYSD reinforcement bars 10mm over dia including all cutting bending binding cranking placing & binding with MS wire (annealed) not less than 0.90mm dia complete all as specified and directed.

M&L for TMT HYSD reinforcement bars 5mm dia and over upto and incl 10mm dia in stirrups, spacers and binders complete all as specified and directed.

M&L for prepration of any surfaces of walls and applying two coats of weather proof anti fungal paint over a coat of alkaliresistant priming paint of approved colour complete all as specified and directed.

M& L for dismantling of Brickwork in cement mortar including all quoins, arches, pillars, etc, but excluding ashlar facings, dresses stonework and precast concrete articles, laid dry omplete all as specified and directed.

Demolition of reinforced concrete of any description and in any position not otherwise specifically provided for including reinforcement cut as required to facilliate demolition complete all as specified and directed.

Taking down cement plaster / terrazzo of any description thickness including raking out joints hacking for key scrubbing down with water all as specified.

Roughning surfaces of old concrete floor by picking, sweeping clean and washing down with water to remove dust complete all as specified and directed

M&L for chequered cement concrete tiles 20cm x 20 cm x 25mm thick, set jointed nad pointed with grey cement and pigment to match over 20mm thick cement screed bed in 1:4 CM complete all as speciifed and directed.

M&L 80mm thick machine pressed precast concrete interlocking paver block and shape and size confirming ti IS 15658-2006 of M-35 Grade with 50mm thick sand cusion grey cement and pigment complete all as specified and directed.

M&L 75mm thick PCC (1:4:8) type D-2 using 40mm graded stone aggregate as in sub base, sib floor of flooring paving path etc surfaces finished even and fair to receive top layer complete all as specified and directed.

Please Enable Macros to View BoQ information