CA NO.GE/AF/BHT-08/2025-26

Amount

Surface excavation n.exc (not exceeding) 30cm deep and averaging 15cm deep and getting out in soft/loose soil complete, all as specified.

Excavating in post holes (or similar holes) each n exc 0.5 cu. m, getting out, returning, filling in and ramming earth or broken rubble mixed with earth around, in layers not exceeding 25cm, watering, and removing surplus soil to a distance n exc 50m and making good surface in SOFT/LOOSE soil complete, all as specified.

Removing excavated spoil to a distance not exceeding 50 metre and depositing where directed at a level not exceeding 1.5 metre above the starting point complete, all as specified.

PCC type C-2 (1:3:6), using 40 mm graded stone aggregates as in foundation filling & mass concrete, complete all as specified.

Cement concrete, type B-1 (1:2:4), using 20 mm graded stone aggregates as in lintels over 1.5 metre clear span, cills, steps, seismic and other similar band, plinth courses, lacing courses , copings, kneelers, apex stones, bed plates, water troughs and the like complete all as specified.

Brick work using bricks as specified in PS clause 5.1, straight or curved on plan exceeding 6.00 metre mean radius built in cement mortar (1:6), complete all as specified.

Aluminium anodised barrel tower bolt of extruded section 200 mm long, ISI marked, complete all as specified.

Aluminium (Die cast) door closer hydraulically regulated designation No. 3 aluminium body universal type suitable for door shutters of 851 to 1000 mm in width and weight between 61 to 80 kg, ISI marked, complete all as specified.

Mortice lock, vertical type size 100mm brass 4 lever fixede in door complete all as specified.

Pre-Painted Galvanized Iron (PPGI) Lead single Door shutter 45 mm thick (Size not exe. 1.20 m x2.00 m including frame materials, Lead sheet thickness 2.00 mm thick , door ( gauge 16) and all accessories/Hardware, hing SS 304 3 nos, Deadlock 1 no, lock key 3 nos, Pin cylinder 1 no, 'D' Handle SS 304 19 mm dia 254 mm 1 no, Door closer 1 no, Glass clear 5 mm thick 2 nos, Hardware nut and bolts, Finisher Screw 9 nos, Concealed flush bolt up to 300 mm1 no, 3 mm double set Gun Tape 1 no, Silicon tube 1 no,complete all as directed by Engg-in-Charge.

Mild steel rolled sections as in main and cross beams, hip and jack rafters, purlin where connected to common rafters and running rails and guides for sliding doors fixed with angle cleats or other connecting plates confirming to grade Fe-410-W Gde E-250, complete all as specified.

Mild steel rolled sections as in roof trusses (framed), trussed, purlins, crane gantries, rails and fastenings and heavy bracket framing (Beam, tee, angle, channel or flat sections) including distance pieces, cleats etc. confirming to grade Fe-410-W Gde E-250, complete all as specified.

Powder coated aluminium (minimum thickness of powder coating 50 micron) frame for doors, windows, ventilators with one or more rebates including joining cleat for fixing etc. complete all as specified.

Powder coated aluminium door shutters with styles & rails, anodised alumnium glazing snap beading, rubber neoprene packing including joining cleats & screws etc as per manufacturers instructions, complete all as specified. NOTES:- (a) Each shutter shall have 2 Nos. 200 mm long almn handles and 03 No. 100 mm size stainless steel/almn butt hinges. (b) Glass and other filling materials in panels including wire cloth and almn grill shall be measured & paid for separately under respective item of BoQ. (c) For powder coated aluminum sections minimum thickness of powder coating shall be 50 micron & minimum weight 0.55 Kg/Metre

Anodised powder coated GI snap grid frame work of size 605mm x 605mm for false ceiling complete with acessories all as specified and shown on serial page No.186 of MES Schedule Part-II.

Hangers 6 mm dia. G.I. (upto 1200mm length) adjusting level fixed to roof slabs / trusses by means of ceilling cleats made out of G.I. flat 40 x 3 mm size 60mm long and expansion hold fasteners 12.5mm dia. 40mm long complete all as specified.

4-6 mm thick E-board, multipurpose, decorative type fixed in grid frme work ceilings as panels, complete all as specified.

Stainless steel waiting bench seating capacity of 03 persons & size ( length not less than 1750 mm longer side) any colour along-with back seat and with side arm rest, complete. NOTE- Design as approved by GE

12mm thick pre-laminated particle board, interior grade, pre-laminated one side with decorative choice lamination & other side balancing white lamination fixed with screw etc complete all as specified

Pre-painted galvalume aluminium zinc coating GI based corrugated steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/ cladding to wall, fixed with self tapping screws comlete all as specified.

Pre-painted galvalume aluminium zinc coating GI based plain steel sheet 0.50 mm of any colour hving tensile strength of 550 Mpa as in roof coverng/cladding to wall, fixed with self tapping screws etc. complete all as specified.

75 mm thick, cement concrete type C-1, 1:3:6 using 20 mm graded stone aggregate as in as sub base in flooring / hardstanding complete all as specified

100 mm thick Plain Cement Concrete 1:4:8 type 2 using 40mm graded crushed stone aggregate as sub base in flooring / hardstanding etc. complete all as specified. NOTE:- The rate included of necessary form work.

Lead free ceramic coloured tiles 10 to 12mm thick (square/ rectangular) area of each tile exc. 0.09 sqm but n. exc. 0.18 sqm laid in floors etc, set and jointed in chemical (as required) & pointed with polymer based grout of matching shade, laid over and including 15 mm thick bedding layer in cement mortar (1:4) directed by Engg-in-Charge.

Lead free ceramic coloured tiles 10 to 12mm thick (square/ rectangular) area of each tile exc. 0.09 sqm but n. exc. 0.18 sqm on vertical surfaces as in skirting, dado etc. set and jointed in chemical (as required) & pointed with polymer based grout of matching shade, laid over and including 10mm thick rendering in cement mortar (1:3) directed by Engg-in-Charge.

Factory made PCC chequered tiles, glossy finish, (Red & Yellow), ISI Marked, with grey cement & pigment, 22-25 mm thick, of size 300 mm x 300 mm, in floors, over & including 20 mm thick cement mortar (1:4) screed, set and jointed with grey cement slurry complete, all as specified.

60 mm thick factory made chamfered edge cement concrete paver block glossy finish, of M-35 grade with approved colour, design & pattern as in footpath, parks, lawns, drive ways or light traffic parking etc., of shape approved by GE, made by table vibratory method using PU mould, laid in required pattern over and including 50 mm thick compacted bed of coarse sand, compacting through vibratory compaction by using plate vibrator, filling the joints with fine sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand; complete.

Rendering 15 mm thick on fair faces of brick work or concrete surfaces, finished even and fair on walls in cement mortar (1:4), complete all as specified.

Complete removal of existing treatment of any description, including prepration of wall surfaces of any description complete all as specified and applying the Two coats of exterior acrylic emulsion over and including a coat of water based exterior primer complete all as specified.

Two coats of cement base paint on new plastered wall surfaces, including preparation of surfaces, complete all as specified.

Plain sheet glass 5mm thick ordinary quality and glazing with rubber gasket in squares exc. 0.5 Sq.m in each pane complete all as specified.

Two coats of synthetic enamel paint over & including a coat of red oxide primer over steel or iron surfaces of any description not other wise described over 10cm width or girth including preparation of surfaces, complete all as specified.

Duo directional road studs of of size 100 mm X 110 mm X 20 mm made up of weather resistant high impact polymer confirming to ASTM D4280 and having electronically welded micro prismatic lens with abrasion resistant coating and fixed with 2 Nos of polymer shanks and epoxy adhesive confirming to IS as per manufacturers instruction complete all as directed. MAKE- Dark eye cat cat part No DA-52, Green lite cat part No GPL-01-04 or equivalent as per appendix B

Metal tubular delineator made out of ABS round body fitted with 2 nos 65 mm dia highly reflective reflectors made out of PMMA and mounted on 45/50 mm dia mild steel pipe of 600 mm height duly powder coated and thermo plastic elastomer 3 bands of Green, red and Yellow reflector radium tape of 25 mm wide strips with anti theft steel net for reflector protection including embedding in PCC 1:2:4 (150 X150 X300 mm) B1 type, complete all as directed.

Convex mirror 900 mm dia on MS tubular Pole of dia 80 mm medium grade of height 1.8 meter above GL painted with red oxide over two coats of synthetic enamel paint fixed in PCC block 1:2:4 (500 X500 X600 mm) type- B2 , complete all as directed by Engg-In-Charge.

Sign board made out of aluminium composite panel board 3mm thick having PVDF coating fixed with stainless steel fancy type screw, skin thickness not less than 0.25mm thick, high intensity reflective maintenance free sheet including writing letters/ site map on both side of sheet as per requirement/ location with high reflective sheet/ tape of make 3 M colour & design as approved including stainless steel frame work with vertical pipes (2Nos) as per 319 AISI, the frame consist of SS Square pipe of size 25mm x 20mm having thickness 1.5mm and vertical post made of SS 50 mm dia pipe, 1.5mm thick, including fixing the legs of sign board in PCC block (B2 1:2:4) of size 500x 500x600 mm complete as directed of following sizes-. Note:- 1. Height of letter exc 150mm but n exc 300mm all as per user requirement 2. Rate inclusive of necessary excavation & PCC work. 3. Top of board shall be fixed at 2.00 mtr height from GL.

Board size 90cm x 60cm

Board size 75cm x 45cm

Taking down cement plaster of any description on brick walls or concrete surfaces etc including raking out joints, hacking for key, scrubbing down with water etc complete all as specified.

Taking down chowkhats or frames with shutters (without taking off shutters from the frames) area exceeding 1.50 Sq.m but not exceeding 4.00 Sq.m each and removing from site all as specified.

Dismantling floor, hearth or wall tiling including cement mortar bedding (but not backing) and removing serviceable tiles to store and rubbish off the premises complete all as specified.

Dismantling wall and ceiling boards with snap grid (fibre, pulp, gypsum, POP, insulation, etc.) or insulation boards/slabs/blankets, any thickness, including cover fillets complete all as specified.

Notes: Amount of credit for retrieved materials is mentioned in tender documents in pdf form which will be deducted while acceptance of tender offline.

MS JAGDAMBA ENTERPRISES (BID ID -3321552)

M/S SHEO KUMAR SINGH AND SONS (BID ID -3321570)

AAHAN CONSTRUCTION (BID ID -3323637)

Bikarma Enterprise (BID ID -3323817)

TRIBENI SINGH AND SONS (BID ID -3321548)

VISHNUDEO CONSTRUCTION (BID ID -3323631)

M/S SAROJ KUMAR SINGH (BID ID -3323890)