Construction of Naibat Office at Basgo ( Balance work ) Under SDP

Providing and fixing 100mm pine wood plain lining tongued and grooved, including wooden plugs compete with necessary screws and priming coat on unexposed surface.10mm thick.

Providing and fixing 12mm thick prelaminated particle board flat pressed three layer or graded wood particle board conforming to IS: 12823 Grade 1 Type II in panelling fixed in aluminium doors, windows shutters and partition frames with C.P. brass / stainless steel screws etc. complete as per architectural drawings and directions of engineer-in-charge. Pre-laminated particle board with decorative lamination on one side and balancing lamination on other side.

French spirit polishing : Two or more coats on new works including a coat of wood filler

Providing and fixing wooden folding room Divider partition for office including hinges and polishing all complete job 12mm-25mm thick.

Supplying installation and testing of Dome Hanging light for office table including wire , LED light holder and light of 12-15 wattt all complete.

Providing and fixing made cup board cabinet made out from 19mm BWP plywood conforming to BIS 710 of green ply/ kitply made all sides shelves, drawer and on back side with 12mm thick water proof ply conforming to BIS 710 and sum mica on all exposed edges of the plywood shall be sum mica with 1.00 white shade with edge beading of same shade and colour incl all approved material / design/ size magnetic catches lock screq adhesive of fevicol make etc all complete of approved design and make as per direction of Enginner in charge ( The unit of measurement is front elevation area )

Earth work in excavation by mechanical means (Hydraulic excavator) over areas (exceeding 30 cm in depth, 1.5 m in width as well as 10 sqm on plan) including getting out and disposal of excavated earth lead upto 50 m and lift upto 1.5 m, as directed by Engineer-in-charge. All kinds of soil

Random rubble masonry with hard stone in foundation and plinth including levelling up with cement concrete 1:6:12 (1 cement : 6 coarse sand : 12 graded stone aggregate 20 mm nominal size) upto plinth level with : Cement mortar 1:6 (1 cement : 6 coarse sand)

Random rubble masonry with hard stone laid dry in foundation, plinth & walls Laid without bond stone

Dumping of stone incuding cost of stones in horozontal on level.

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size).

Steel reinforcement for R.C.C. work including straightening, cutting, bending, placing in position and binding all complete upto plinth level.Thermo-Mechanically Treated bars of grade Fe-500D or more.

Centering and shuttering including strutting, propping etc. and removal of form for Suspended floors, roofs, landings, balconies and access platform

Edges of slabs and breaks in floors and walls Under 20 cm wide

Providing and fixing precoated galvanised iron profile sheets (size, shape and pitch of corrugation as approved by Engineer-in-charge) 0.50 mm (+ 0.05 %) total coated thickness with zinc coating 120 grams per sqm as per IS: 277, in 240 mpa steel grade, 5-7 microns epoxy primer on both side of the sheet and polyester top coat 15-18 microns. Sheet should have protective guard film of 25 microns minimum to avoid scratches during transportation and should be supplied in single length upto 12 metre or as desired by Engineer-in-charge. The sheet shall be fixed using self drilling /self tapping screws of size (5.5x 55 mm) with EPDM seal, complete upto any pitch in horizontal/ vertical or curved surfaces, excluding the cost of purlins, rafters and trusses and including cutting to size and shape wherever required.

Structural steel work riveted, bolted or welded in built up sections, trusses and framed work, including

Providing & fixing upto floor five level precast cement concrete solid blocks including hoisting and setting in position in cement mortar 1:3 (1cement:3 coarse sand), cost of required centring, shuttering and curing complete1:3:6 (1 cement : 3 coarse sand : 6 graded crushed stone aggregate 20 mm nominal size)

15 mm cement plaster on the rough side of single or half brick wall of mix : 1:4 (1 cement: 4 fine sand)

Providing and applying white cement based putty of average thickness 1 mm of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Finishing walls with water proofing cement paint of required shade : New work (Two or more coats applied @ 3.84 kg/10 sqm)

Cutting holes of required size in brick masonry wall for fixing of exhaust fan including providing and fixing 300 mm dia PVC pipe conforming BIS-12818 and making good the same etc. complete as per direction of Engineer-in-charge.

Exhaust fan 300mm size ( Heavy duty ) CG transiar or equivalent approved make.

Providing and fixing 25 ltr Geyser including all complete job.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank ISI : 12701 marked with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Supply, installation, testing & commissioning of 1.5 HP single phase AC electric motor along with all the required connections complete job ( approved brand )

providing and fixing of roller blinds made of polyester fabric wirh spring / chain operated mechanism, including aluminium roller tube, bradkets, fittings and accessories, complete in all respects as directed by engineer in charge.

Carriage of material from source to site of work by MT Cement & steel an avg lead 40 km

Sand & S/agg an avg lead 8 Km

Stone an avg lead 5 km

Please Enable Macros to View BoQ information