GE/S(U)-05/2021-22 PROVN OF 01 X TOILET ROOM WITH 03 X URINAL POINT AAD BRANCH IN BLDG NO P-107 COVERED SHED PASSAGE PATHWAY COMPOUND WALL AND OTHER ALLIED WORKS OF BLDG NO NP-130 WALL PANELLING MS LADDER RENOVATION OF TOILET ROOM AND OTHER ALLIED WO

Amount

Surface dressing not exceeding 15 cm deep in hard/dense soil complete all as specified and directed.

Excavation in trenches not exceeding 1.5 M wide and not exceeding 1.5 M in depth for foundation complete all as specified and directed.

PCC 1:4:8 type D-2 (using 40 mm graded aggregate) in foundation filling and mass concrete complete all as specified and directed.

Brick work with sub class 'B' brick, straight or curved on plan exceeding 6 M Mean radius built in type CM 1:6 complete all as specified and directed.

Returning filling in including spreading levelling watering and well ramming in layers not exceeding 25 cm complete all as specified and directed.

Removing excavated material exceeding 500 m but not exceeding 1.5 km and depositing where directed at a level not exceeding 1.5 m above the starting point complete all as specified and directed.

Damp proofing course to horizantal or vertical surface including form work in PCC 1:2:4 type B-1, 25 mm thick complete all as specified and directed.

Hard core of guage not exceeding 63 mm deposited spread and levelled in layers not exceeding 15 cm thick watered and rammed to a true surface complete all as specified and directed.

75 mm thick PCC 1:3:6 type C-1 (using 20 mm graded stone aggregate) as in sub base floor complete all as specified and directed.

75 mm thick for PCC 1:3:6 (using 20 mm graded aggregate) as in plinth protection using extra cement complete all as specified and directed.

Non skid ceramic coloured tiles 400 x 400 x 7 mm thick in floors etc. set and jointed in neat cement slurry and pointed in white or coloured cement to match over 15 mm thick screed bed in CM 1:6 complete all as specified and directed.

15 mm thick rendering in CM 1:6 on brick/ concrete surfaces of walls finished even rough/ smooth complete all as specified and directed.

Glazed ceramic tiles in vertical surface but 600 x 300 x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Rendering 15 mm thick in CM 1:6 on brick work and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 15 mm thick in CM 1:4 on brick work and finished even and smooth without using extra cement complete all as specified and directed.

Rendering 5 mm thick in CM 1:3 on ceiling and exposed surface of concrete finsihed even and smooth without using extra cement complete all as specified and directed.

Preparation of new plaster surfaces wall surface applying three coats of white wash complete all as specified and directed.

Preparation of new plaster surfaces applying two coats of cement base paint and over one coat of primers complete all as specified and directed.

Preparation of new plaster surfaces applying three coats of white wash on ceiling complete all as specified and directed.

Form work to edges of concrete flat slats sides of RCC/PCC bands etc. in walls horizental or slopping exceeding 10 cm but not exceeding 20 cm wide rough finished surfaces complete all as specified and directed.

Form work to soffits of suspended slabs and similar work not exceeding 200 mm thick complete all as specified and directed.

Form work to sides and soffit of floor or roof beams lintels, beam haunching, girders lintal cantiliver including supports overhung etc. complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for slabs supported on walls beams and columns in floors, roof, landing, balconies, canopies slabs and in shelves and the like complete all as specified and directed.

RCC type B-1 1:1 1/2:3 (using 20 mm graded aggregate) for for lintals bends and roof bends complete all as specified and directed.

TMT bars 10 mm dia and over and cut to length bent to shape required including cranking, bending, hooking ends and bending with MS wire not less than 0.9 mm dia or securing with clips quality confirming complete all as specified and directed.

Mild steel bars 5 mm dia and over upto and including 10 mm dia in stirrups, spacers and binder TMT bars cut to length bent to shape required including cranking, bending spirally including mild steel wire not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Solid PVC door frame of size 50 x 47 mm made out of 5 mm plain colour sheet reinforced with MS square tube all as per specififcation and drawing and complete all as specified and directed by Engr-in-Charge.

Factory made solid PVC door shutter 30 mm thick (Style) consisting of frame made out of MS tubes for top and bottom railsMS frame shall be coverred with heat moulding plain colour PVC C channels having a PVC sheets strips of 20 mm width struck inside with solvent cement for stiles and plain colour PVC sheets for top rail, lock rail & bottom rail on either side & as gap insert for top rail & bottom rail panelling of plain colour PVC sheets to be fitted in the MS frame welded/sealed to the stiles & rails with suitable complete all as specified and directed.

100 mm size butt hinges extruded aluminium alloy with galvanised with galvanised mild steel hinges pin anodised type B-2 complete all as specified and directed.

200 mm long aluminium anodised barrel tower bolts of extruded section complete all as specified and directed.

Aluminium handles cast type of 150 mm size complete all as specified and directed.

Steel Ventilators with top hung shutters including hinges steel peg stay complete all as specified and directed.

Sheet glass 3 mm thick figured glass, pin headed type and glazing with oil putty or wooden beads not exceeding 0.5 Sqm in Each pane complete all as specified and directed.

GI tubes 15 mm dia medium grade laid in trenches or fitted on walls complete all as specified and directed.

GI tubes 20 mm dia medium grade laid in trenches or fitted on walls/floor complete all as specified and directed.

110 mm PVC (SWR) pipes single socket in any length with rubber ring joints fixed to wall complete all as specified and directed.

110 mm PVC (SWR) bends any redius with access door or without access door complete all as specified and directed.

110 mm PVC (SWR) branch piece, (singal T) equal or unequal with access door complete all as specified and directed.

110 mm PVC (SWR) vent cowl complete all as specified and directed.

100 mm dia, PVC (SWR) floor trap, plain with grating including jointing with solvent cement in repair complete all as specified and directed.

100/110 mm PVC (SWR) pipes single socket in any lenth with rubber ring joints fixed to wall and floor complete all as specified and directed.

100 mm PVC (SWR) bends any redius with access door complete all as specified and directed.

PVC (SWR) gully trap 125/110 mm, settting and jointing with solvent cement in repair complete all as specified and directed.

Vitreous china ware wash down water closet pan, (pedestal pattern) coloured including connection to drain and to flushing pipe, anti syphonage pipe etc. complete all as specified and directed.

10 ltrs capacity PVC valveless syphonic action type flushing cistern low level with inlet ball valve float and handle complete all as specified and directed.

Vitreous china white wash hand basin (flat back or angle back type) size 550 x 400 mm white including brackets, pedestal, wast fittings brass chromium plated, CP waste cupling, 32 mm dia, waste pipe, PVC connection 15 mm bore with PTMT nuts of length including 15mm dia CP pillar tap fancy type complete all as specified and directed.

Health faucet ABS body with wall hook and 1 mtr chrome plated PVC hose pipe in repair complete all as specified and directed. Make : CERA, Cat Part No : F8030103 or equvalent in CERA.

Chromium plated toilet paper holder complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1153N or equvalent in CERA.

Glass shelf with chromium plated guard rails complete all as specified and directed. Make : Jaquar, Cat Part No : ACN-1171N or equvalent in CERA.

600 mm long brass chromium plated towel rail fancy type complete all as specified and directed. Make : Jaquar, Cat Part No : ACN-1111NM or equvalent in CERA.

Soap dish complete all as specified and directed. Make : Jaquar, Cat Part No : ACN 1131N or equvalent in CERA.

Taking out any type of cables, pipes or any type of utilities found above or benith the ground level and laying/reconnecting the same away from working area/site, including material and labour utilised in the same complete all as specified and directed.

Anti-termite treatment of bottom and sides of excavation at the rate of 5 ltr of emulsion per square metre of surface area complete all as specified and directed by Engr-in-Charge.

Anti-termite treatment of the top surface of filled earth at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and directed by Engr-in-Charge.

Anti-termite treatment of the soil under plinth protection at the rate of 5 ltr of emulsion per square metre of surface complete all as specified and directed by Engr-in-Charge.

Providing and injecting Along the external wall below concrete or masonry apron using Antitermite Treatment chemical emulsion @ 2.25 litres per linear metre including drilling and plugging holes etc. in apron complete all as specified and directed. Note : The treatment work shall be carried through authorised agencey only and certificate for the same for warranty shall have to frunished before submitting payment (The same applicable for ser item No 54 to 57).

CP waste coupling 32 mm dia PTMT (half or full threaded) minimum weight 450 gms complete all as specified and directed.

PVC waste pipe 32 mm bore with cup and washers complete all as specified and directed.

15 mm bore centre hole basin mixer with round spout with 450 mm long copper pipes and brass nuts with out Pop up complete all as specified and directed. Make : Jaquar, Cat Part No : CON 167KNB

Self closing angle cock pressmatic for urinal with flange and 200 mm connecting pipe and spreader complete all as specified and directed. Make : Jaquar, Cat Part No : PRS 077

PVC connection 15 mm bore 450 mm long Braided Hose with M10X1 Nipple, 15 mm Nut, O-Ring & Rubber washer (Suitable for Basin Mixers) complete all as specified and directed. Make: Jaquar, Cat Part No : ALD-803AB

PVC connection 15 mm bore 450 mm long Braided Hose with two 15 mm Nut, & Rubber washer without nipple complete all as specified and directed. Make : Jaquar, Cat Part No : ALD-805B

CP Bib taps cast copper alloy with crutch or butterfly handle two bay, screwed for iron pipe of dia 15 mm, fancy type fixed complete all as specified and directed.

CP angle valves cast copper alloy, fancy type, with iong shank and cup, bore 15 mm fixed complete all as specified and directed.

125 mm dia brass chromium plated shower rose with swivel joints complete all as specified and directed.

600 mm long tubular tower rail brass chromium plated 20 mm dia, D type 60 cm long fixed with two plugs (Gutties) of 2nd class hard woodembeded in cement mortor 1:3 with MS screws complete all as specified and directed.

Taking down of PVC water tanks of capacity upto 500/1000 ltr and providing new one of 1000 ltr capacity rotational moulded polythene water storage tanks (cylindrical vertical with closed top) all as per SSR Part-I 2009 complete all as specified and directed. Note :- Necessary tank nipple, float valve, gate valve etc. shall be paid separately under respective item of this schedule if required.

20 mm dia gun metal globe or gate valves with iron wheel head screwed both ends for iron pipe complete all as specified and directed.

20 mm ball valves high pressure of PTMT with epoxy coated aluminium rod & high density plastic ball screwed for iron pipes and fixed for iron pipes complete all as specified and directed.

750 mm x 450 mm Urinal partition made up of 10 mm thick toughened glass duly sand blasted including stainless steel holding clamps complete all as specified and directed by Engr-in-Charge.

Large urinal large 420 x 395 x 635 mm complete all as specified and directed by Engr-in-Charge. Make : CERA, Cat Part No : S4020102 or equivalent model of makes specified in PS.

Demolition of brick/stone, PCC Blocks wall built in cement mortar including all quoins, arches, pillar etc. complete all as specified and directed.

Roughing surfaces of new/old concrete surfaces by picking up, sweeping, cleaning and washing down with water to remove dust etc. including taking down tarfelt and brushing neat cement slurry @3kg/Sqm mixed with water proofing compound including 20 mm thick screeding in CM (1:4) finished even and smooth mixed with water proofing compound (WPC shall be measured and paid separatley) complete all as specified and directed.

3 mm thick plain polymeric water proofing membran of weight not less than 3.5 Kg per Sqm and bonded completely to the surfaces with overlap of 10 cm (overlap to be thermo fused by flame) to be laid by company complete all as specified and directed by Engr-in-Charge.

Supply only (LW+) water proofing liquid solution complete all as specified and directed.

Excavation in trenches not exceeding 1.5 m wide and not exceeding 1.5 m in depth for foundation or manholes etc. and area not exceeding 10 Sqm on plan and getting out in any type soil complete all as specified and directed.

Cement concrete type D-2 (1:4:8) (using 40 mm graded stone aggregate) as in foundation filling and mass concerete complete all as specified and directed.

SWG drain pipe grade 'A' of 150 mm internal dia laid in trenches and jointed in cement mortar (1:1) complete all as specified and directed.

Concrete bed to drain pipes including packing under and haunching against the sides of pipes after they are laid and tested in cement concrete type D-2 (1:4:8) for 150 mm dia pipe complete all as specified and directed.

Brick work with sub class 'B' bricks straight or curved on plan exceeding 6 mtr mean radius built in CM (1:4) as in manholes, septic tank, filter bed, walls, drains etc complete all as specified and directed.

Precast reinforced cement concrete (1:2:4) type B-1 (using 20 mm graded stone aggregate) for manhole cover septic tank, drain covers slabs etc. including necessary form work and set in CM (1:4) complete all as specified and directed. Note :- reinforcement will be measured and paid seperately.

TMT bars 6 mm to 8 mm dia and over, cut to length, bent to shape required, including cranking, bending spirally for hooping for colunms, hooking ends and binding with and including mild steel wire (annealed) not less than 0.9 mm dia or securing with clips complete all as specified and directed.

Removing excavated soil to a distance exceeding 50 m and not exceeding 1.50 km out side defence land complete all as specified and directed.

Excavation in post holes (or similar holes) each not exceeding 0.5 Cum and getting out in dense type of soil complete all as specified and directed.

PCC (1:2:4) type B-1 (using 20 mm graded aggregate) as in foundation, filling in post holes complete all as specified and directed.

Roof trusses framed section Fe-410-W (Gde-E-250) quality A, trussed, rafter, purlins, crane gantries rails and fastenings and heavy brackets, post, framed for eves board and similar work framing (beam, tee, channel or flat sections) including distance pieces cleats including welding reavrign etc. complete all as specified and directed.

(Plain or chequered) channels, square cut or notched (oridinary and counter sunk) forming holes, without any attatchment complete all as specified and directed.

Mild steel bolts purpose made with hexagonal or square head one end each screwed other end to be fitted with washers and one hexagonal or square nut. Dia of shank of bolt not exceeding 16 mm and not exceeding 10 cm long complete all as specified and directed.

Preparation of new steel surfaces and applying two coats of synthetic enamel paint over a coat of red oxide complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based corrugated steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Pre-painted galvalume aluminum zinc coating GI based Plain steel sheet 0.50 mm thick of an colour having tensile strength of 550 Mpa as in roof covering/cladding to wall fixed with self tapping screws complete all as specified and directed.

Framed work such as grills, gratings etc. with ends of bars shouldered and/or riveted, or forged into spikes; framed guard bars; barred iron doors; ladders; framed balusters; walk ways; railings; frame work of water tanks staging and similar work confirming to Fe.290 Gde-E-165 complete all as specified and directed.

PCC 1:3:6 type C-1 (using 20 mm graded crushed stone aggregate) as in surface channel and drains including necessary formwork and extra forming fair finsished drain or channels for inner girth in cement concrete etc. complete all as specified and directed.

Surface excavation not exceeding 30 cm deep and averaging 15 cm deep and getting out in hard and dense soil complete all as specified and directed.

Demolition of cement concrete in ground floor and pavings not exceeding 15 cm thick below or above ground level complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in level course on floor etc complete all as specified and directed.

15 mm thick screed bed in cement mortar 1:4 for laying floor finishes under floor complete all as specified and directed.

Dura stone (heavy duty) tiles of size 305 mm x 305 mm x 10 mm thick as in floors set and jointed in neat cement slurry and pointed in coloured cement to match the surface of tiles complete all as specified and directed. Note : Shade/colour as approved by GE.

Sand cushion 20 to 30 mm thick for laying and fixing interlocking tiles complete all as specified and directed.

Machine pressed precast concrete interlocking paver block (glossy finish) any shape and size (sample approved by GE) confirming to IS 15658-2006 of 60 mm thickness M-35 grade with grey cement and pigment complete all as specified and directed by Engr-in-Charge.

Providing 100 mm thick, plain cement concrete type B-1, (1:2:4) (using 20 mm graded aggregate) as in sub base of floors complete all as specified and directed.

PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in coping, benching and similar work etc. including necessary form work complete all as spcified and directed.

PCC 1:2:4 type B-1 (using 20 mm graded aggregate) as in lintels upto 1.5 Mtr cills, parapets, copings apex stones, bed plates, precast factory made kerbs stone or in benching complete all as specified and directed.

Precasted RCC jallies 45 to 50 mm thick (measured solid) including all mouldings but excluding frames confirming to type B-0 (using 12.5 mm graded crushed stone aggregate) complete all as specified and directed.

Walling of square/rectangular, random rubble, uncoursed well bonded, bedded and solidly hearted built in cement mortar 1:6 complete all as specified and directed.

Raking out joints/pointing squared/rectangular, random rubble masonry, coursed or uncoursed, random rubble or polygonal rubble uncoursed or brought up to courses complete all as specified and directed.

Flush pointing to random rubble masonry, uncoursed or brought upto course masonary in CM 1:3 complete all as specified and directed.

Raised pointing to random or polygonal rubble, uncoursed on brought upto courses random rubble stone masonary in CM 1:4 complete all as specified and directed.

Taking down cement plaster and raking out joints, hacking for key, scrubbing down with water built in cement mortar complete all as specified and directed.

Preparation of new plastered surface and applying two coats of oil bound distempering over a coat of primer and two coat of wall care putty complete all as specified and directed.

Two coats of cement base paint over a coat of alkali resistant priming paint inluding thin coat of wall care putty preparation of newly plastered surfaces complete all as specified and directed.

New/old plaster surface of walls and applying two coat of oil bound distempers over one coat of primer and two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Dismantling floor hearth or wall tiling including cement mortar bedding but not backing complete all as specified and directed.

Rendering 10 mm thick on fair faces of brick work or concrete surface in CM 1:4 on vertical surfaces /backing coat complete all as specified and directed.

Vitrified tiles (double charge) colored 600 x 600 mm and 10 mm thick as in floors jointed in neat cement slurrry and pointed in white cement sluurry to match the shade of existing surfaces complete all as specified and directed. Note : The contractor shall have no claim on difference what so ever on shade/colour of tile.

All as per ser item No 116 but in vertical surfaces complete all as specified and directed.

Vitreous china wash down water closet pan (pedestal pattern) white with plastic water closet seat & back with flat bottom and cover, mild steel chromium plated or aluminium anodised hinging device (excluding flushing cistern and flush pipe) but including fixing bolt and necessary connection with existing pipes fixed in repairs complete all as specified and directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 15 mm bore including taking down old pipe complete all as specified and directed.

Steel tubing galvanized, medium grade with all fittings, laid in floors or fixed to walls, 20 mm bore including taking down old pipe complete all as specified and directed.

Stop valves cast copper alloy chromium plated fancy type, screwed both ends for iron pipe 15 mm bore in repair complete all as specified and directed.

Taking down chowkats or frames exceeding 1.5 Sqm but not exceeding 4.0 Sqm each with shutters (without taking off shurtters from the frame with all fitting) complete all as specified and directed.

Taking down chowkhats with shutter (without taking off from shutter) not exceeding 1.5 sqm each and removing to store complete all as specified and directed.

PVC moulded door frame of size 50 x 47 mm made out of 5 mm plain colour PVC sheet reinforced with MS square tube, supplying and fixing in opening as per specification and drawing complete all as specified and directed.

150 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

250 mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet sliding bolts of extruded sections and fixing bolts and sliding bolts of extruded section and fixed complete all as specified and directed.

300 mm aluminium alloy, anodised, sliding door bolt with hasp, staple (bolt type) and fixing clips of sheet, cast or extruded section and fixing bolts and sliding bolts of extruded section or cast aluminium alloy and fixed complete all as specified and directed.

Pressed steel frame 105 x 60 mm for doors with one or more rebates including necessary fixing lugs, hinges, lock strike plate etc. complete all as specified and directed.

PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) for filling in pressed steel door frame complete all as specified and directed.

Flat iron hold fast fixed to frame (25 mm x 3 mm) of length 20 cm complete all as specified and directed.

Second class hard wood 35 mm thick plain frames panelled door shutters (any number of pannels) with of veenerred particle board medium density wood particle boards with commercial face supplied and fitted to chowkhats complete all as specified and directed.

Preparation of new wooden surface of any description over 10 cm width or girth and applying two coats of synthetic enamel paint over a coat of pink primer complete all as specified and directed.

MS butt hinges 100 mm long, medium weight cold rolled, fixed to timber frame work of doors complete all as specified and directed.

CP towel rail 20 mm dia & 600 mm long including a pair of CP brackets fixed with plastic rawl plugs & CP screws complete all as specified and directed.

75 mm bore PVC (SWR) pipes single socketed in any length with rubber ring joints laid in trenches or in floors complete all as specified and directed.

20 mm thick granite (of any type) (table rubbed and polished) in cooking plat forms and like in CM 1:4 including pointing in white cement 1:2 using marble dust with admixture of pigment to match with shade of granie complete all as specified and directed.

Cutting holes in brick wall exceeding half brick but not exceeding one brick built in cement mortar or cement lime morter and stone wall built in lime morter and making good with dismantled portion in CM 1:3 or cement concrete 1:2:4 type B-0 complete all as specifed and directed by Engr-in-Charge.

Dismantling wrought iron or mild steel work of any escription not otherwise provided for gate complete all as specified and directed.

Collapsible gate, top hung, consisting of channel pickets, pivoted flat bars. Top and bottom runners brass handles etc as specified, erected in position and securing runners with hold fasts and brackets complete mathc execsting position complete all as specified and directed.

Two coats of synthetic enamel paint over one coat of red oxide primer on steel surfaces of any description, over 10 cm in width or girth, not otherwise described including preparation of new surfaces complete all as specified and directed.

PVC wall lining consisting of 5 mm thick plain colour PVC sheet inclusive of solvent cement and fixing at site on PVC frame as per site requirement complete all as specified and directed by Engr-in-Charge.

10 mm thick PVC sheet fillets of width 35 mm for wall paneling inclusive of fixing to wall to make PVC frame as per site requirement complete all as specified and directed by Engr-in-Charge.

Taking down frames with shutters (without taking off shutters from the frame) area not exceeding 1.5 Sqm each including iron mongery complete all as specified and directed.

Powder coated 15 micron aluminium door of approved design complete all as specified and directed with all fixing arrangement including providing and fixing door handle, tower bolts, mortice lock 6 lever (Make - Harrison/Godrej) one on each door and aluminium Powder coated tower bolts 200 mm long (03 Nos on each shutters) and 5 mm thick tinted glass pane of glazed shutter along with aluminium glazing beading of size 19.00 mm x 17.5 mm x 0.70 mm @ weight of 0.097 Kgs per RM including rubber gasket on both side complete alongwith neoprene lining. The member shall be made out of extended aluminium sesction comprising of :- (Size of the door shall be as per site requirement) (a) Door frame of size 95.25 mm x 44.50 mm x 1.70 mm @ 1.301 Kg/RM.. (b) Shutter vertical member 85 x 44.50 x 1.56 mm @ 1.39 Kg per RM. (c) Shutter top member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. (d) Shutter bottom member 101.60 x 44.50 x 1.60 mm @ 1.301 Kg per RM. (e) Shutter lock rail member 83.50 x 44.50 x 1.54 mm @ 1.139 Kg per RM. The actual measurement shall be taken, wastage shall be including in the rates, the above sections are from JINDAL/INDAL/HINDAICO/WALCO extruion. The contractor is at liberty to choose high section from approved make with minor variation in sizes and weight as approved. However nothing extra shall be paid for over size and over weight section also.

Plain cement concrete 1:2:4 type B-2 (using 40 mm graded stone aggregate) as in channels and drains, foundation and similar work etc. complete all as specified and directed.

300 mm dia reinforced concrete pipes, class NP-2 laid and jointed complete with collars complete all as specified and directed.

25 mm thick PCC 1:2:4 type B-0 (using 12.5 mm graded aggregate) as in level course on floor etc complete all as specified and directed.

Vitrified ceramic tiles (Double charge), area of each tile not exceeding 0.36 Sqm, 10 mm thick (square or rectangular) of superior quality as in floor surfaces set and jointed in neat cement slurry and pointed in white or coloured cement to match the light shade of tiles complete all as specified and directed.

False ceiling with 12 mm thick glass fibre reinforced Gypsum ceiling tiles of size 595 x 595 mm, prima fine fissured micro look white coloured using aluminium powder coated "T" section 25 x12 mm grid and 6 mm dia GI suspension wire etc complete all as specified and directed. Make : Armstrong/Diamond or equivalent.

Applying 3 mm thick wall care putty on wall surfaces and well rubbing for making smooth and uniform surface with sand paper then applying two coats of oil bound distemper in different patterns shade with rolling instrument including a coat of primer on decorative surfaces etc. complete all as specified and directed by Engr-in-Charge.

Supply only Water proofing compound (WPC) complete all as specified and directed.

Cutting upto a depth of 2.5 cm into concrete walls and trimming surface as required, girth exceeding 30 cm with or without reinforcement complete all as specified and directed.

Aluminium Camposit Panel (ACP) wall paneling 6 mm thick HPL sheet, aluminium cover sheet thickness 0.5 mm surface finish PVDF 25/30 micron, length 2240 mm and width 1220 mm, interior face coil coated with polyster, fixing with aluminium tube/aluminium chanel 25 x 50 mm, 2 mm thick aluminium/steel rivet/screw with expansion fastener and including silicom filling in approved pattern as in columns beam, wall drop facia etc. in any position and height in any colour including preparation of concrete surface for ACP complete all as per direction of Engr-in-Charge.

PCC type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in coping benching and the like including form work complete all as specified and directed.

Cement concrete type D-2 1:4:8 for concrete bed to 300 mm dia RCC drain pipe including packing under and haunching against the sides of pipes after they are laid & testing complete all as specified and directed.

PCC type B-1 (1:2:4) (using 20 mm graded crushed stone aggregate) as in surface channels and drain beds complete all as specified and directed.

100 mm thick plain cement concrete, type C-1, (1:3:6) (using 20 mm graded aggregate) as in plinth protection complete all as specified and directed.

25 mm thick PCC type B-0, 1:2:4 (using 12.5 mm graded crushed stone aggregate) as in sub base finished fair for receiving floor finishes complete all as specified and directed.

Screed bed or bedding layer of mortar 15 mm thick for laying floor tiles in CM 1:4 complete all as specified and directed.

Machine cut kota stone slab flooring 18 to 20 mm thick overs cement screed base laid and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing complete all as specified and directed.

All as per ser item No 161 but as in riser to steps, skirting dado fixed with cement mortar 1:4 complete all as specified and directed.

18 to 20 mm thick white marble slabs in narrow widths fixed with neat cement slurry as in floor including grinding and polishing mirror finish (ganite polish) complete all as specified and directed.

10 mm thick backing coat on vertical surfaces such as skirting/dado in CM 1:4 for laying tiles complete all as specified and directed.

Brick work with sub class "B" bricks straight or curved on plan to any radius in half brick thick wall in cement mortar 1:4 complete all as specified and directed.

Preparation of new plastered or un-plastered surfaces and walls including cornices, pilasters etc and applying two coats of cement base paint over a coat of primer over thin coat of wall care putty complete all as specified and directed.

Complete removal of existing treatment and applying two coats of oil bound distemper over a coat primers with two coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Complete removal of existing treatment applying two coat of cement base paint over a coat of primer paint on walls over thin coat of wall care putty complete all as specified and directed by Engr-in-Charge.

Taking down frames with shutters (without taking off shutters from the frame) area exceeding 1.5 Sqm but not exceeding 4 Sqm Each including iron mongery complete all as specified and directed.

Steel window (box type) factory made with side hung shutters including pintol hinges, steel handles, steel peg stay and all locking arrangement complete with glazing bars dovetailed or welded including one shop coat of red oxide primer complete all as specified and directed. Note : i) The window shall be fabricated as per Drg No CEUZ/TD/1269/2008 Sheet 1/3 to 3/3 ii) MS fillets, glazing, wire gauge shall be measured and paid separately.

All as per ser item No 170 but wire gauge shutters complete all as specified and directed.

35 mm thick flush shutter, solid core construction, with block board core and plywood face panels, commercial type complete all as specified and directed.

3 mm thick glass sheet oridinary qlty in steel or wooden frames complete with fixing materials such as putty glazing pins wooden beads etc. complete all as specified and directed.

Galvanished mild steel wire cloth 0.56 mm nominal dia of wire and average width of apperature 1.18 mm complete all as specified and directed.

10 mm thick PVC sheet fillets of width 50 mm for wall paneling inclusive of fixing to wall to make PVC frame as per site requirement complete all as specified and directed by Engr-in-Charge.

Sinks with drainage board made of stainless steel 1 mm thick kitchen or laboratory with plugs, washers and wastes including bedding in cement mortar to dwarf wall including fixing cantilever brackets and connecting union to pipe fixed in repairs complete all as specifice and directed.

Aluminium powder coated frame, window shutters (glazed, wire gauge and grill) side hung with aluminium window frame or chowkhat 1.5 mm thick aluminium powder coated of size 100 mm x 44.5 mm and window shutter frames glazed and wire gauze (middle, top rail, bottom rail) and styles 1.5 mm thick aluminum powder coated of size 44.5 x 44.5 mm including powder coated aluminium grill 50 mm x 50 mm aparture and all fitting such as rubber gasket, aluminium glazing clips locking cabinet, 4 mm thick tinted glass pane for glazed shutters, stainless steel wire mesh for gauge shutter and hook and eye for each shutter fixed with rubber gasket and glazing clip/aluiminium beads aluminium tower bolt 75 mm 02 Nos each shutter, aluminium butt hinges 75 mm 02 Nos in each shutter aluminium handle 100 mm 01 No in each shutter including 5 mm thick tinted galss all accessories complete all as specified and directed.

Powder coated anodised aluminium frames for doors, partitions, windows, ventilators with one or more rebates including jointing cleats for fixing etc complete all as specified and directed.

Powder coated aluminium anodised ventilator shutters, fixed type without sash bar, aluminium section weighing 0.55 kg/m including necessary jointing cleat glazing clips, rubber packing, anodised aluminium snap beading screws with lowered shutter with 3 mm thick pin head figured glass etc. complete all as specified and directed.

Glazed ceramic tiles in vertical surface but 450 mm x 300 mm x 7 mm thick set and jointed in neat cement slurry and pointed in white or coloured cement to match complete all as specified and directed.

Non skid ceramic joint free tiles 7 to 10 mm thick area of each tile exceeding 0.18 Sqm and not exceeding 0.36 Sqm in floors etc set and jointed in neat cement slurry and pointed in white or coloured cement to match the slurry complete all as specified and directed.

Vitreous china urinals, bowl type (back or corner wall type), complete including provideing and fixing plugs, bedding urinal against wall in cement mortar 1:2 securing urinal to plugs with and including 60 mm long brass screws pointing around urinal back in cement, fixing automatic flushing cistern with brackets, flush pipe grating and union for discharge pipe complete all as specified and directed.

Stop valve of PTMT any colour screwed for iron pipe and fixed 15 mm bore (Prayag or equivalent) in repair complete all as specified and directed.

GI pipe medium grade 20 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and directed.

GI pipe medium grade 15 mm bore in wall and ceiling or laying in floors, including new fittings as required at site complete all as specified and directed.

100 mm long aluminium anodised barrel tower bolt of extruded section complete all as specified and directed.

Aluminium handles cast type anodised 100 mm long complete all as specified and directed.

250 mm long aluminium anodised sliding door bolt with hasp and staple (bolt type) and fixing clips of sheet sliding bolts of extruded sections and fixing bolts and sliding bolts of extruded section and fixed complete all as specified and directed.

Demolition of and breaking up of AC/PVC/CI rain water pipes any dia fixed in any position complete all as specified and directed.

100 mm bore cast iron soil, sand cast, waste and vent pipes in any length with or without ears, with cement joints laid in trenches or in floors complete all as specified and directed.

All as per ser item No 190 but fixed to wall complete all as specified and directed.

100 mm cast iron sanitary connections short connections pipe of length upto 300 mm complete all as specified and directed.

All as per ser item No 192 but single complete all as specified and directed.

Cast iron bends (any radius), diminishing pieces or tapers (larger bore measured) for 100 mm bore fitted with oval access doors complete all as specified and directed.

Cast iron bends (any radius), with duck's foot or heel rest 100 mm dia complete all as specified and directed.

Extra over cast iron pipes and fittings if lead joint is provided in lieu of cement joint for 100 mm pipe complete all as specified and directed.

150 mm/100 mm size gratings of PTMT but with waste hole (minimum weight of 100 gms) complete all as specified and directed.

Looking mirror 5.5 mm thick of Make' Modiguard' or 'Ashashi' mounted on 5 mm thick PVC Sheet including power coated aluminium beadinng of approved pattern complete all as specified and directed.

Bib taps with wall flange chromium plated complete all as specified and directed. Make : Jaquar, Cat Part No : VGP-81037

Angular stop cock with wall flange complete all as specified and directed. Make : Jaquar, Cat Part No : VGP-81053.

Pillar cock with lift type operating know base of wall flange complete all as specified and directed. Make : Jaquar, Cat Part No : FLR-5015

Towel ring square with round flange complete all as specified and directed. Make : Jaquar, Cat Part No : ACN-1121N.

Tumbler holder chromium plated with holder and bracket complete all as specified and directed. Make : Jaquar, Cat Part No : AQN.

Hand shower (Health faucet) with 8 mm dia, 1 mtr long flexible tube and wall hook complete all as specified and directed. Make : Jaquar, Cat Part No : ALD-573.

Toilet paper holder complete all as specified and directed. Make : Jaquar, Cat Part No : CAN 1155N.

Towel rack 600 mm long with out lower hangers but with three hooks complete all as specified and directed. Make : Jaquar, Cat Part No : CAN 1181N

Glass shelf 600 mm long with holding brackets complete all as specified and directed. Make : Jaquar, Cat Part No : CAN 1171N.

Corner glass shelf with chromium plated rails including brackets complete all as specified and directed. Make : Jaquar, Cat Part No : CAN 1173.

Wash hand basin oval white 665 x 495 mm complete all as specified and directed. Make : CERA, Cat Part No : WHB-1028, Pedestal-1118.

Chromium plated 32 mm bore size full threaded with 80 mm height including all necessry washers complete all as specified and directed.

Water closet Pedestal pattern colour as approved and complete all as specified and directed by Engr-in-Charge. Make : CERA, Cat Part No (EWC 2015 cistern 2115 Seat cover 2315 Twin flush cistern 2205/BT TWIN CLAIR DELUXE flush fitting including PVC connection.

Excavation in trenches not exceeding 10 Sqm on plan not exceeding 1.5 m deep and not exceeding 1.5 m wide, getting out in any type (hard/dense) of soil complete all as specified and directed.

Plain cement concrete 1:3:6 type C-2 (using 40 mm graded stone aggregate) as in mass concrete and foundation filling complete all as specified and directed.

PCC type C-1, 1:3:6 (using 20 mm graded crushed stone aggregate) as in surface channel and drain beads including all necessary form work complete all as specified and directed.

Extra for forming fair finished drain or channel 70 cm inner girth in cement concrete, using extra cement, including forms moulds, mitered/stopped ends etc. complete all as specified and directed.

Supply only integral water proofing compound complete all as specified and directed.

Concrete 1:3:6 type C-2 (using 40 mm graded aggregate) as in bed to 150 mm drain pipes including packing under and haunching against the sides of pipes after they are laid and tested for complete all as specified and directed.

Salt glazed stone ware drain pipe 150 mm bore in trenches and jointed complete all as specified and directed.

Framed work as in frames to manhole covers of angle or other section including hold fast confirming Fe-410-O complete all as specified and directed.

Cutting in to existing manhole or boundary wall for connecting new drains, making good to pipe and rendering, cutting out existing benching and forming branch channel (1/2 round or 3/4 section) in cement concrete 1:2:4 type B-1 smooth finished and reforming benching as required complete all as specified and directed.

All as per ser item No 181 but in vertical surfaces complete all as specified and directed.

Taking down shutter only exceeding 1.00 Sqm but not exceeding 2.00 Sqm and fixing in the same opening of any description complete all as specified and directed.

Aluminum alloy anodised sliding door bolt 300 mm size in old or new position complete all as specified and directed.

Two coats of synthetic enamel paint on new wooden surfaces including preparation over a coat of pink primer complete all as specified and directed.

One coat of synthetic enamel paints over a coat of on old steel surfaces including preparation of surfaces complete all as specified and directed.

Point wiring for one light/fan/bell point controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistranded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes thickness (1.25 mm) & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts copper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed. Make: Havells/Finolex/ Polycab/L&T

All as per ser item No 226 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 227 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

Switch Piano flush type 6 Amps single pole one way (Modular Type) with outer strip complete all as specified and directed. Make : Havells (Crabtree)/Legrand/Philips

Socket 2-in-1, 3 Pin 6 Amps (Modular Type) with outer strip complete all as specified and directed. Make : Havells (Crabtree)/Legrand/Philips

Ceiling rose surface bakelite 3 terminals complete all as specified and directed. Make : Cona Cat Part No : 2126/SSK Cat Part No 572 or equivalent of make in Make : Havells/Legrand/Polycab

Exhaust fan Ventil Air - DS 300 mm including louver & making hole for Exhaust fan works complete all as specified and directed. Make - Havells/Polycab/Bajaj.

Sheet metal enclosure MCB distribution board single pole & neutral 240 volts 4 way with IP-43 IK-09 protection double door complete with appropriate size bus bar and neutral link, fixed flush in wall including chases wall for fixing DB and making good distributed wall surfaces to match with existing specification complete all as specified and directed. Note - MCBs will be measured separately. Make : HPL/Havells/ Indoasian.

Replacement MCB Single Pole, 230 Volt, Raiting 6 to 32 Amps Product Code: CSMBS1B32 complete all as specified and directed. Make : C&S

Replacement MCB Single Pole and Neutral, 230 Volt, Raiting 63 Amps, Product Code: CSMBS1B63N complete all as specified and directed. Make : C&S

New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 20 W complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Part No : LHEXBXPNIN1W020 or equivalent to Crompton/Syska.

Replacement of New E-Lite LED Curve, high lumen batten with efficacy of 100 lumens in 10 W complete all as specified and directed by Engr-in-Charge. Make - Havells Cat Part No : LHEXBXPNIN1W010 or equivalent to Crompton/ Syska.

Replacement of LED bulk head luminaire, 10 W (ENDURA RUGBY) Cat Part No LHEOAOP7UZ6W010 230 Volts wall/surface mounted complete with with LED lamp 10 watt, with all accessories, pre-wired, including providing flexible copper wire, twin core cable complete all as specified and directed by Engr-in-Charge.

Sub main wiring with three single core PVC insulated with copper conductor cable stranded of size 2x4 Sqmm FRLS in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 1x2.5 Sqmm FRLS as earth lead complete all as specified and directed. Including taking down old sub main wire.

Taking down carefully, copper/aluminum point wiring (light, fan, socket or power/LED Light fittings) complete fitting such as switch, sockets, ceiling rose, pendants socket any type, rectangular board terminal boxes etc. and making good disturbed surfaces of walls floors and ceiling complete all as specified and directed. Keeping the LED lights in safe custody.

Point wiring for one light/fan/Exhaust fan controlled by one switch using 1.5 Sqmm FRLS copper conductor cables (multistanded) PVC insulated and unseathed in and including PVC concealed conduit (thickness not less than 1.5 mm and 20 mm dia), medium grade with Modular metal flush boxes & PVC back plate for mounting modular type in adequate module of switches, sockets & regulators etc. with front plate modular type including supplying and laying PVC insulated unsheathed 1100 volts coppper conductor cable 1.5 Sqmm as earth wire stranded and conected to earth dolly complete all as specified and directed.

LED 12 Watt Surface Panel Round light complete all as specified and directed by Engr-in-Charge. Make - Wipro Product Code No D621265 or Equivalent to Syska/Bajaj/Havells.

Industrial Exhaust fan 450 mm sweep ventilating fan heavey duty, 230 volts, single phase with self closing complete with louvres including taking down old unserviceable exhaust fan complete all as specified and directed. Make: Havells/ Crompton/Bajaj.

Ducting with GI sheet of 20 guage for 2 Nos of Exhaust fan from underground bathroom to outside area with security arrangement at the opening of duct for preventing the unnecessary item to get into the duct complete all as specified and directed.

Cutting holes into or through brick walls built in cement mortar and making good in cement mortar 1:3 or cement concrete 1:2:4 type B-1 as required with super ficial area not exceeding 150 Sqcm complete all as specified and directed.

Iron frame of any shape and size for exhaust fan of sweep 450 mm complete all as specified and directed.

Dismantling all the false ceiling and broken ducting of Air passing for repair purpose complete all as specified and directed.

Point wiring for one light point/fan/bell point controlled by one switch with 1.5 Sqmm PVC insulated FRLS unsheathed copper conductor single core multi stranded flexible copper cable in and including not less than 2.00 mm thick 20 mm dia and over Non metallic Rigid PVC surface/ Concealed Conduit (ISI marked) with and all accessories 1.5 mm thick mild steel terminal boxes concealed on walls, painting the same inside and out side with one coat of black bitumen paint with 3 mm thick hylam brand bakelite sheet cover for fixing of piano switches/sockets/ regulator etc. along with PVC insulated and unsheathed FRLS 1.5 Sqmm multi stranded copper conductor cable (green color) as earth lead, & connected to common earth and earthdolly, making good the disturbed surface to match with the existing specification complete all as specified and directed by Engr-in-Charge. Make - KEI or equivalent make in polycab/finolex

All as per ser item No 248 but for 3 pin 6 Amps socket outlet independent including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 248 but for 3 pin 6 Amps socket outlet on the same board including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire and connected to earth dolly complete all as specified and directed.

All as per ser item No 248 but for 3 Pin 16 Amps socket outlet independent with cable 2.5 Sqmm including copper PVC insulated PVC unsheathed 1.5 Sqmm earth wire standard and connected to earth dolly complete all as specified and directed.

Switch piano flush button single pole one way 5 amps 240 volt complete all as specified and directed.

Switch socket combination 5 Amps 2-in-1, 5 Pin flush type, 230 volts complete all as specified and directed.

Socket outlet 2 in 1, 3 pin, 5A complete all as specified and directed.

Sub main wiring with two single core PVC insulated with copper conductor cable stranded of size 6 Sqmm in PVC concealed conduit 25 mm dia including PVC insulated copper conductor cable 4 Sqmm as earth lead complete all as specified and directed. Including taking down old sub main wire.

M/S ASHOK KUMAR PACHIALA

RAMAN CONSTRUCTION CO