Proposed Construction of Collectorate Building with Facilities at Deoghar

Amount

Earth work in excavation in foundation trenches in ordinary soil ( vide classification of soil item A) and disposal of excavated earth as obtained to a distance upto 50M including all lifts leveling ramming the foundation treanches, removing roots of trees, and shrubs all complete as per approved design, building specification and direction of E/I.

Extra for earth work in hard soil as per specification & direction of engineer in charge (Vide classification of soil item B)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed, fully compacted and fine dressed with earth obtained from excavation of foundation trenches within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode of measurement compacted volume)

Filling in foundation trenches and plinth in layers not exceeding 150mm thick well watered, rammed fully compacted and fine dressed with earth obtained after cutting within a lead of 50M and lift of 1.5M all complete as per building specification and direction of E/I. (Mode measurement compacted Volume).

Providing coarse clean Sand in Filling in foundation trenches or in plinth including ramming and watering in layers not exceeding 150mm thick with all leads and lifts including cost of all materials, labour, royalty and taxes all complete as per building specification and direction of E/I. (Mode of measurement compacted volume).

Preparation of mounds of various size and shape by available excavated / supplied earth in layers not exceeding 20 cm in depth, breaking clods, watering of each layer, dressing etc., lead upto 50 meter and lift upto 1.5 m complete as per direction of Officer-in-charge.

water bond macadam Providing, laying spreading & compacting stone aggregates of specific size to water bond macadam specification including spreading in uniform thickness hand packing, rolling with vibratory roller 8-10 tone / smothery wheeled steel roller in stages to proper gate & chamber, applying and booming requisite type of screening / binding materials to fill up the interstices of course aggregate, water and compacting to the required density.(B) By mechanical means (b) Using screening Type - A (13.2mm Agg.) with vibratory roller

Dry Lean Cement Concrete Sub- base (Construction of dry lean cement concrete Sub- base over a prepared sub-grade with coarse and fine aggregate conforming to IS: 383, the size of coarse aggregate not exceeding 25 mm, aggregate cement ratio not to exceed 15:1, aggregate gradation after blending to be as per table 600-1, cement content not to be less than 150 kg/ cum, optimum moisture content to be determined during trial length construction, concrete strength not to be less than 10 Mpa at 7 days, mixed in a batching plant, transported to site, laid with a paver with electronic sensor, compacting with 8-10 tonnes vibratory roller, finishing and curing.)

Cement Concrete Pavement (Construction of un-reinforced, dowel jointed, plain cement concrete pavement over a prepared sub base with 43 grade cement @ 400 kg per cum, coarse and fine aggregate conforming to IS 383, maximum size of coarse aggregate not exceeding 25 mm, mixed in a batching and mixing plant as per approved mix design, transported to site, laid with a fixed form or slip form paver, spread, compacted and finished in a continuous operation including provision of contraction, expansion, construction and longitudinal joints, joint filler, separation membrane, sealant primer, joint sealant, debonding strip, dowel bar, tie rod, admixtures as approved, curing compound, finishing to lines and grades as per drawing )

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:2:4 (1 Cement : 2 coarse sand (zone-III) : 4 graded stone aggregate 40 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level :1:3:6 (1 Cement : 3 coarse sand (zone-III) : 6 graded stone aggregate 20 mm nominal size)

Providing and laying in position cement concrete of specified grade excluding the cost of centering and shuttering - All work up to plinth level : 1:4:8 (1 Cement : 4 coarse sand (zone-III) : 8 graded stone aggregate 40 mm nominal size)

Providing and laying cement concrete in retaining walls, return walls,walls (any thickness) including attached pilasters, columns, piers,abutments, pillars, posts, struts, buttresses, string or lacing courses,parapets, coping, bed blocks, anchor blocks, plain window sills, fillets,sunken floor,etc., up to floor five level, excluding the cost of centering,shuttering and finishing :1:1½:3 (1 cement:1½ coarse sand:3 graded stone aggregate 20 mm nominal size)

Providing and laying in position specified grade of reinforced cement concrete, excluding the cost of centering, shuttering, finishing and reinforcement - All work up to plinth level : 1:1.5:3 (1 cement : 1.5 coarse sand (zone-III): 3 graded stone aggregate 20 mm nominal size) Foundation

Reinforced cement concrete work in walls (any thickness), including attached pilasters, buttresses, plinth and string courses, fillets, columns, pillars, piers, abutments, posts and struts etc. above plinth level up to floor five level, excluding cost of centering, shuttering, finishing and reinforcement : Column

Reinforced cement concrete work in beams, suspended floors, roofs having slope up to 15° landings, balconies, shelves, chajjas, lintels, bands, plain window sills, staircases and spiral stair cases above plinth level up to floor five level, excluding the cost of centering, shuttering, finishing and reinforcement with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) : 3 graded stone aggregate 20 mm nominal size). Beam

Providing, hoisting and fixing above plinth level up to floor five level precast reinforced cement concrete in shelves, including setting in cement mortar 1:3 (1cement : 3 coarse sand), cost of required centering, shuttering and finishing with neat cement punning on exposed surfaces but , excluding the cost of reinforcement, with 1:1.5:3 (1 cement : 1.5 coarse sand(zone-III) derived from natural sources : 3 graded stone aggregate 20 mm nominal size derived from natural sources).

Providing Tor steel reinforcement of all dia rods as per approved design and drawing exclusive carriage of M.S. bars to work site, cutting, bending and binding with annealed wire with cost of the wire, removal of rust, placing the rods in position all complete as per building specification and direction of E/I. TMT Fe 500 (only valid for Tata (Tiscon),SAIL,JSPL,Electrosteel Steel Ltd.Bokaro &Vizag ( RINL)

Providing Tor steel reinforcement of 8mm. dia rods as per approved design and drawing -do- -do- TMT Fe 500 do-do

Providing Tor steel reinforcement of 10mm.,28mm,32mm Dia. bars as per approved design and drawing -do- -do -

Providing Tor steel reinforcement of 12mm,16mm,20mm,25,Dia. bars as per approved design and drawing -do- -do-

Centering and shuttering including strutting, propping etc. and removal of form for : Foundations, footings, bases of columns, etc. for mass concrete

Centering and shuttering including strutting, propping etc. and removal of form work for : Retaining walls, return walls, walls (any thickness) including attached pilasters, buttresses, plinth and string courses fillets,kerbs and steps etc.

Centering and shuttering including strutting, propping etc. and removal of form for : Suspended floors, roofs, landings, balconies and access platform

Centering and shuttering including strutting, propping etc. and removal of form for : Shelves (Cast in situ)

Centering and shuttering including strutting, propping etc. and removal of form for : Lintels, beams, plinth beams, girders, bressumers and cantilevers

Centering and shuttering including strutting, propping etc. and removal of form for : Columns, Pillars, Piers, Abutments, Posts and Struts

Centering and shuttering including strutting, propping etc. and removal of form for : Stairs, (excluding landings) except spiral-staircases

Centering and shuttering including strutting, propping etc. and removal of form for : Weather shade, Chajjas, corbels etc., including edges

Providing precast cement concrete Jali 1:2:4 (1 cement : 2 coarse sand(zone-III) : 4 graded stone aggregate 6mm nominal size ), reinforced with 1.6 mm dia mild steel wire, including centering and shuttering, roughening cleaning, fixing and finishing in cement mortar 1:3 (1 cement: 3 fine sand) etc. complete, excluding plastering of the jambs, sills and soffits. 50 mm thick

Providing 25mm thick Damp Proof Course with cement concrete M-200 with nominal mix of (1:1.5:3) with approved quality of stone chips of 20mm to 6mm size graded and clean course sand of F.M. 2.5 to 3 including screening, shuttering and mixing cement concrete in mixer with 5% cicio or any other approved water proffing compound and placing in position, striking, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 75 A brick work in C.M. (1:6) in foundation and plinth with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/l.

Providing designation 75B brick work in C.M. (1:6) in foundation and plinth approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes an

Providing designation 75B brick work in C.M. (1:6) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, costs of screening, materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Provideing 25 mm thick water proff plaster (1:3) with clean coarse sand of F.M 1.5 with 5% cico or any other apporoved water proffing compound including screening , curing with all leads and lifts of water scaffolding taxes and royalty all complete as per building specefication and direction of E/I

Extra for brick work for each consecutive floor above first floor including watering and scaffolding, all complete as per direction of E/I.

Providing designation 125mm thick reinforced designation 75A brick work in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carriage of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforcement) all complete as per building specification and direction of E/I.

Providing Ashlar Stone masonry in C.M. (1:6) in foundation and plinth with chisel dressed stone, cut to requred zise and shape and cleane coarse sad of F.M. 2 to 2.5 includimg coat of screening, carriage of material raking out joints to 20 mm depth curing, taxes and royalty all complete as per building specification and direction of E/I

Providing designation 100A brick work with flyash lime brick (FLAG) confirming to IS 12894-1990 (9"x4.5"x3") in C.M. (1:4) in super structure with approved quality of clean coarse sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints costs of screening materials, scaffolding, raking out joints to 15mm depth curing taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:6) in superstructure with approved quality of clean sand of F.M. 2 to 2.5 including providing 10mm thick mortar joints, cost of screening materials, raking out joints to 15mm depth, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing designation 112mm thick reinforced designation 100A brick work with fly ash lime brick (FLAG) confirming to IS 12894-1990 (9" x 4.5" x 3") in C.M. (1:4) in superstructure with approved quality of clean coarse sand of F.M. 2 to 2.5 including the cost of screening, carraige of materials, scaffolding, raking out joints to 15mm depth, curing, taxes and royalty (but excluding the cost of reinforced) all complete as per building specification direction of E/I.

Providing designation 75B one brick flat soling joints fitted with local sand including cost of watering taxes royalty all complete as per building specification and direction of E/I.

Providing average 150 mm thick dry rammed koha beaten to 112 mm. (Compacted with water ) made of well burnt or jhama bricks including ramming properly till compacted thickness is achieved, curing and carriage of water with all leads, making proper slope and blending the top with cement mortar (1:10) all complete as per building specification and direction of E/I.

Providing 12mm cement mortar (1:3) with clean coarse sand of F.M. 1.5 with floating coat of neat cement in skirting including rounding of junctions with floor, curing, taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm cement plaster (1:3) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 12mm thick cement plaster (1:6) with clean coarse sand of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 6mm thick cement plaster (1:4) in ceiling with clean of F.M. 1.5 including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 1.5 mm. cement punning including curing carrage of water withall leads and lifts as per building specification and direction of E/I

Providing 12mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/I.

Providing 19 mm thick water proof cement plaster (1:3) with clean coarse sand of F.M. 1.5 with 5% cico or any other approved water proofing compound including screening, curing with all leads and lifts of water, scaffolding taxes and royalty all complete as per building specification and direction of E/l.

Extra for plaster work over exterior surface for each consecutive floor above first floor including cost of scaffolding etc. all complete as per direction of E/I.

Providing and applying plaster of paris putty of 2 mm thickness over plastered surface to prepare the surface even and smooth complete.

Providing and applying white cement based putty of average thickness 1 mm, of approved brand and manufacturer, over the plastered wall surface to prepare the surface even and smooth complete.

Providing two coats of oil bound distemper of approved shade and make over a coat of cement primer over new surface including preparing the plastered surface by rubbing smooth with pumice stone or fine sand paper applying putty wherever required scaffolding washing of floors and taxes all complete as per building specification and direction of E/I.

Providing two coats of plastic emulsion paint of approved shade and make over a coat of cement primer over new surface including preparing plastered surface by rubbing smooth with pumice stone or fine sand paper, applying putty wherever required scaffolding, washing of floor and taxes all complete as per building and specification of E/I.

Finishing walls with Acrylic Smooth exterior paint of required shade : New work (Two or more coat applied @ 1.67 ltr/10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/10 sqm)

Finishing walls with Premium Acrylic Smooth exterior paint with Silicone additives of required shade : New work (Two or more coats applied @ 1.43 ltr/ 10 sqm over and including priming coat of exterior primer applied @ 2.20 kg/ 10 sqm)

Providing and laying Double charged vitrified floor tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less then 0.08% and conforming to IS: 15622/ISO 13006 of approved make, in all colours and shades, laid on 20 mm thick cement mortar 1:4 (1 cement:4 Coarse sand0, jointing with grey cement slurry @ 3.3 kg/sqm including grouting the joints with wite cement and matching pigments etc, complete Size of tiles 600 x 600 mm.

Kota stone slab flooring over 20 mm (average) thick base laid over and jointed with grey cement slurry mixed with pigment to match the shade of the slab, including rubbing and polishing complete with base of cement mortar 1 : 4 (1 cement : 4 coarse sand) : 25 mm thick

Kota stone slabs 20 mm thick in risers of steps, skirting, dado and pillars laid on 12 mm (average) thick cement mortar 1:3 (1 cement: 3 coarse sand) and jointed with grey cement slurry mixed with pigment to match the shade of the slabs, including rubbing and polishing complete.

Providing and laying 25mm thick. Kotah stone slab flooring of approved size, texture and colour over 19mm thick base of lime mortar (1:1:1) (lime putty:surkhi:coarse sand) laid over and jointed with grey cement slurry mixed with pigment to match the shade of slab including rubbing and polishing to granolithic finish with approved quality of carborandum stone including cost of curing, taxes and royality all complete as per building specification and direction of E/I. (iv) 600 x 600 mm size

Providing and laying rectified Glazed Ceramic floor tiles of size 300x300 mm or more (thickness to be specified by the manufacturer), of 1st quality conforming to IS : 15622, of approved make, in all colours, shades, except White, Ivory, Grey, Fume Red Brown, laid on 20 mm thick Cement Mortar 1:4 (1 Cement : 4 Coarse sand), jointing with grey cement slurry @ 3.3 kg/ sqm including pointing the joints with white cement and matching pigments etc., complete.

Providing and fixing Ist quality ceramic glazed wall tiles conforming to IS: 15622 (thickness to be specified by the manufacturer), of approved make, in all colours, shades except burgundy, bottle green, black of any size as approved by Engineer-in-Charge, in skirting, risers of steps and dados, over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and jointing with grey cement slurry @ 3.3kg per sqm, including pointing in white cement mixed with pigment of matching shade complete.

Providing and fixing 18 mm thick gang saw cut, mirror polished, premoulded and prepolished, machine cut for kitchen platforms, vanity counters, window sills, facias and similar locations of required size, approved shade, colour and texture laid over 20 mm thick base cement mortar 1:4 (1 cement : 4 coarse sand), joints treated with white cement, mixed with matching pigment, epoxy touch ups, including rubbing, curing, moulding and polishing to edges to give high gloss finish etc. complete at all levels. Granite of any colour and shade Area of slab over 0.50 sqm

Extra for providing edge moulding to 18mm thick marble stone counters,Vanities etc. over Item No. 8.2 including machine polishing to edge to give high gloss finish etc. complete as per design approved by Engineer-in-Charge Granite work

Precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Light shade pigment using white cement

Chequerred precast cement concrete tiles 22 mm thick in footpath & courtyard, jointed with neat cement slurry mixed with pigment to match the shade of tiles, including rubbing and cleaning etc. complete, on 20 mm thick bed of cement mortar 1:4 (1 cement: 4 coarse sand). Medium shade pigment using 50% white cement 50% Grey cement

Providing and laying 500x500x40 mm thick Turf paver (Turfpave XD) on 150 mm thick sub grade of compacted bed of 20 mm thick nominal size stone aggregate and base course and filling with 150 mm thick jamuna sand, including spreading, well ramming, consolidating and finishing smooth etc. all complete as per direction of Engineer-in-charge

Providing and fixing Glass mossaic tiles at finished plain wall surface of size 20 mm x 20 mm x 4 mm in all colour, design , fixing in customize design as per direction of Engineer-in- Charge. The glass mosaic tiles to be fixed on the wall surface with the help of approved adhesive applied at the rate of 2.5 kg per sqm and grouting of the same. The rate is inclusive of all operation, material and required pattern approved by Engineer-in- Charge:

Providing and laying flamed finish Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing, curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge : Flamed finish granite stone slab Jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Polished Granite stone flooring in required design and patterns, in linear as well as curvilinear portions of the building all complete as per the architectural drawings with 18 mm thick stone slab over 20 mm (average) thick base of cement mortar 1:4 (1 cement : 4 coarse sand) laid and jointed with cement slurry and pointing with white cement slurry admixed with pigment of matching shade including rubbing , curing and polishing etc. all complete as specified and as directed by the Engineer-in-Charge. Polished Granite stone slab jet Black, Cherry Red, Elite Brown, Cat Eye or equivalent.

Providing and laying Vitrified Cool Roof tiles in different sizes (thickness to be specified by the manufacturer) with water absorption less than 0.08% and conforming

Extra for flooring work for each consecutive floor above first floor complete as per direction of E/I

Providing & Laying Vitrified Paring / Industrial Tiles - Size of Tile (300X300x10 mm size )

Stone tile (polished) work for wall lining over 12 mm thick bed of cement mortar 1:3 (1 cement : 3 coarse sand) and cement slurry @ 3.3 kg/sqm including pointing in white cement complete. 8mm thick Granite of any colour and shade

Wall lining butch work upto 10m height with Dholpur stone 40 mm thick rough facing on the exposed surface with stone strips of minimum length 300 mm and required width, including embedding every tenth layer and bottom most layer in masonry or concrete after making necessary chases of size 75x75 mm and by providing layer of 75 mm thick strips i/c 12 mm thick bed of cement mortar 1:3 (1 Cement : 3 coarse sand) i/c ruled pointing in cement mortar 1:2 (1 white cement : 2 stone dust) with an admixture of pigment to match the shade of stone complete as per direction of Engineerin- charge.

Providing and laying 60mm thick faciory made cement concrete interlocking paver block of M -30 grade made by block making machine with strong vibratory compaction, of approved size, design & shape, laid in required colour and pattern over and including 50mm thick compacted bed of coarse sand, filling the joints with line sand etc. all complete as per the direction of Engineer-in-charge.

Providing and laying factory made chamfered edge Cement Concrete paver blocks in footpath, parks, lawns, drive ways or light traffic parking etc, of required strength, thickness & size/ shape, made by table vibratory method using PU mould, laid in required colour & pattern over 50mm thick compacted bed of sand, compacting and proper embedding/laying of inter locking paver blocks into the sand bedding layer through vibratory compaction by using plate vibrator, filling the joints with sand and cutting of paver blocks as per required size and pattern, finishing and sweeping extra sand. complete all as per direction of Engineer-in-Charge. 60mm thick cement concrete paver block of M-35 grade with approved colour, design & pattern.

Providing and fixing pressed steel door frames conforming to IS: 4351, manufactured from commercial mild steel sheet of 1.60 mm thickness, including hinges, jamb, lock jamb, bead and if required angle threshold of mild steel angle of section 50x25 mm, or base ties of 1.60 mm, pressed mild steel welded or rigidly fixed together by mechanical means, including M.S. pressed butt hinges 2.5 mm thick with mortar guards, lock strikeplate and shock absorbers as specified and applying a coat of approved steel primer after pre-treatment of the surface as directed by Engineerin-charge:Profile C Fixing with adjustable lugs with split end tail to each jamb

Supplying, fitting and fixing good quality, well dressed and well seasoned sal wood work in chaukhat in doors, windows skylights, fanlights and C/W celetial windows openings, including wedge over all clamps complete including application of two coats of wood preservative of approved quality on the surface butting walls and lintels all complete as per building specification and direction of E/I.

Supplying, fitting and fixing 35mm thick solid core type decorative double leaf flush door shutter with both sides decorative veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting and fixing 35mm thick solid core type decorative single leaf flush door shutter with one sides teak decorative and another side commercial veneered with black board core bended with high quality phenol formal dehydes synthetic resin of standard make with Aluminium fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/l.

Supplying, fitting & fixing 35mm thick solid core type non-decorative single leaf flush shutters in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneeres of standard makew with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Supplying, fitting & fixing 35mm thick solid core type non-decorative double leaf flush shutter in doors and windows with black board core blended with high quality phenol formal dehyde synthetic resin both side commercial veneeres of standard makew with oxidised iron fittings such as hinges, tower bolts, handle, cleats and sand blocks and taxes all complete as per building specification and direction of E/I.

Providing & Fixing decorative high pressure laminated sheet of plain / wood grain in gloss / matt/ suede finish with high density protective surface layer and reverse side of adhesive bonding quality conforming to IS : 2046 Type S, including cost of adhesive of approved quality 1.5 mm thick

Providing and fixing PVC rigid foam sheet 1 mm thick on existing door shutters (bathroom and W.C. doors) using synthetic rubber based adhesive.

Providing and fixing factory made P.V.C. door frame of size 50x47 mm with awall thickness of 5 mm, made out of extruded 5mm rigid PVC foam sheet, mitred at corners and joined with 2 Nos of 150 mm long brackets of 15x15 mm M.S. square tube, the vertical door frame profiles to be reinforced with 19x19 mm M.S. square tube of 19 gauge, EPDM rubber gasket weather seal to be provided through out the frame. The door frame to be fixed to the wall using M.S. screws of 65/100 mm size, complete as per manufacturer’s specification and direction of Engineerin- Charge.

Providing and fixing factory made panel PVC door shutter consisting of frame made out of M.S. tubes of 19 gauge thickness and size of 19 mm x 19 mm for styles and 15x15 mm for top & bottom rails. M.S. frame shall have a coat of steel primers of approved make and manufacture. M.S. frame covered with 5 mm thick heat moulded PVC 'C' channel of size 30 mm thickness, 70 mm width out of which 50 mm shall be flat and 20 mm shall be tapered in 45 degree angle on both side forming styles and 5 mm thick, 95 mm wide PVC sheet out of which 75mm shall be flat and 20 mm shall be tapered in 45 degree on the inner side to form top and bottom rail and 115 mm wide PVC sheet out of which 75 mm shall be flat and 20 mm shall be tapered on both sides to form lock rail. Top, bottom and lock rails shall be provided both side of the panel. 10 mm (5 mm x 2 ) thick, 20 mm wide cross PVC sheet be provided as gap insert for top rail & bottom rail, paneling of 5 mm thick both side PVC sheet to be fitted in the M.S. frame welded/ sealed to the styles & rails with 7 mm (5 mm+2 mm) thick x 15 mm wide PVC sheet beading on inner side, and joined together with solvent cement adhesive. An additional 5 mm thick PVC strip of 20 mm width is to be stuck on the interior side of the 'C' Channel using PVC solvent adhesive etc. complete as per direction of Engineer-in-charge, manufacturer's specification & drawing. 30 mm thick pre laminated PVC door shutters

Providing and fixing fire resistant door frame of section 143 x 57 mm having built in rebate made out of 16 SWG G.I. sheet (zinc coating not less than 120 gm/sqm) duly filled with vermuculite based concrete mix, suitable for mounting 60 minutes fire rated door shutters. The frame is fitted with intumuscent fire seal strip of size 10x4 mm (minimum) alround the frame and fixing with dash fastener of approved size and make, including applying a coat of approved brand fire resistant primer etc. complete as per direction of Engineer-in-charge (Dash fastener to be paid for separately).

Providing and fixing 50 mm thick glazed fire resistant door shutters of 60 minutes fire rating conforming to IS:3614 (Part-II), tested and certified as per laboratory approved by Engineer-in-charge, with suitable mounting on door frame, consisting of vertical styles, lock rail, top rail 100 mm wide, bottom rail 200 mm wide, made out of 16 SWG G.I.sheet (zinc coating not less than 120 gm/m2) duly filled FR insulation material and fixing with necessary stainless steel ball bearing hinges of approved make, including applying a coat of approved fire resistant primer etc. all complete as per direction of Engineer-in-charge (panneling to be paid for separately).

Providing and fixing glazing in fire resistant door shutters, fixed panels & partitions etc., with G.I. beading made out of 1.6 mm thick G.I. sheet (zinc coating not less than 120 gm/m²) of size 20 x 33 mm screwed with M4 x 38 mm SS screws at distance 75 mm from the edges and 150 mm c/c , including applying a coat of approved fire resistant primer/ powder coating of not less than 30 micron on G.I. beading, & special ceramic tape of 5 x 20 mm size etc complete in all respect as per NBC 2016, IS 16231 (Part 3):2016 and as per direction of Engineer-in-charge with glass of required thickness having 60 minutes of fire resistance both integrity & radiation control (EW60) and minimum 20 minutes of insulation (EI20). The manufacturer have to give test report/certification of fire glass and the glass should have the stamp showing the value of

E, EW & EI. The glass shall be tested in approved NABL accredited lab or by any other accreditation body which operates in accordance with ISO/IEC 17011 and accredits labs as per ISO/IEC 17025 for testing and calibration scopes shall be eligible. The maximum glazing size shall not be more than 1100x2200 mm (w x h) or 2.42 sqm.

Providing and fixing panic bar / latch (Double point) fitted with a single body, Trim Latch & Lock on back side of the Panic Latch of reputed brand and manufacture to be approved by the Engineer- in- charge, all complete.

Providing and fixing ISI marked aluminium butt hinges anodised (anodic coating not less than grade AC 10 as per IS: 1868) transparent or dyed to required colour or shade with necessary screws etc. complete: 125x63x4 mm

Providing and fixing aluminium extruded section body tubular type universal hydraulic door closer (having brand logo with ISi, IS : 3564, embossed on the body, door weight upto 36 kg to 80 kg and door width from 701 mm to 1000 mm), with double speed adjustment with necessary accessories and screws etc. complete.

Providing and fixing bright finished brass 100 mm mortice latch and lock, ISI marked, with six levers and a pair of anodised (anodic coating not less than grade AC 10 as per IS : 1868) aluminium lever handles of approved quality with necessary screws etc. complete.

Steel work welded in built up sections/ framed work, including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer using structural steel etc. as required. In gratings, frames, guard bar, ladder, railings, brackets, gates and similar works

Providing and fixing M.S. grills of required pattern in frames of windows etc. with M.S. flats, square or round bars etc. including priming coat with approved steel primer all complete. Fixed to openings /wooden frames with rawl plugs screws etc.

Supplying, fitting & fixing M.S. Grill made of 20x6mm flat as per approved design and drawing aproperly fabricated with joints continuous fitted, welded and finished smooth, hoisting as per building specification and direction of E/I.

Supplying, fitting and fixing collapsible gate of approved size and make properly fabricated with vertical double channels 20 x 10 x 2mm at 100mm centers and braced with M.S. flat diagonals 20 x 3mm with top and bottom rails of T.iron 40 x 40 x 6mm with 38mm dia steel pulleys complete with bolts, nuts, locking arrangement, stoppers, handles, including applying a priming coat of red lead paint, car riage, hoisting and taxes all complete as per building specification and direction of E/I.

Supplying, fitting and fixing M.S. grill gate with M.S. grills made of 20x6mm M.S. flats or 16mm square bars fitted on 25x25x6mm M.S Angle frame including cost of fabrication , providing necessary locking arrangement with haskal and domny duly fixed in P.C.C. (1:2:4) blocks of required size, applying a priming red lead paint over steel work, taxes all complete as per drawing specification and direction of E/l. (where steel is not supplied by the deptt.)

Structural steel work in section, fixed with or without connecting plate, including cutting, osting, fixing in postion and applying a priming coat of approved steel primer all complete.

Providing two coats of synthetic enamal paint of apporoved shade and make over new wooden surfaceincluding cleaning the surface after removing dirt, scales smokes grease and sand papering , including cost of scaffolding and taxes all complete as per building specefication as direction of E/I

Prividing French spirit polishing over new wooden surface to give desired texture and gloss with apporoved make and shade of ready mixed french polish including preparing the surface sfter cleaning removing dirt

Providing primer one coat of red lead paint ofapproved make over steel surface including preparing the surface after cleaning removing dirt, scales, grease and sand papering, including cost of scaffolding etc. all complete as per building specification direction of E/I.

Providing two coats of synthetic enamel paint of approved shade and make over steel surface including cleaning the surface thoroughly cost of scaffolding and taxes all complete as per building specification and direction of E/I.

Providing and fixing stainless steel ( Grade 304) railing made of Hollow tubes, channels, plates etc., including welding, grinding, buffing, polishing and making curvature (wherever required) and fitting the same with necessary stainless steel nuts and bolts complete, i/c fixing the railing with necessary accessories & stainless steel dash fasteners , stainless steel bolts etc., of required size, on the top of the floor or the side of waist slab with suitable arrangement as per approval of Engineer-incharge, (for payment purpose only weight of stainless steel members shall be considered excluding fixing accessories such as nuts, bolts, fasteners etc.).

Providing and fixing aluminium work for doors, windows, ventilators and partitions with extruded built up standard tubular sections/ appropriate Z sections and other sections of approved make conforming to IS: 733 and IS: 1285, fixing with dash fasteners of required dia and size, including necessary filling up the gaps at junctions, i.e. at top, bottom and sides with required EPDM rubber/ neoprene gasket etc. Aluminium sections shall be smooth, rust free, straight, mitred and jointed mechanically wherever required including cleat angle, Aluminium snap beading for glazing / paneling, C.P. brass / stainless steel screws, all complete as per architectural drawings and the directions of Engineer-in-charge. (Glazing, paneling and dash fasteners to be paid for separately) : For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately) Powder coated aluminium (minimum thickness of powder coating 50 micron)

For shutters of doors, windows & ventilators including providing and fixing hinges/ pivots and making provision for fixing of fittings wherever required including the cost of EPDM rubber / neoprene gasket required (Fittings shall be paid for separately)

Anodised aluminium (anodised transparent or dyed to required shade according to IS: 1868, Minimum anodic coating of grade AC 15)

Powder coated aluminium (minimum thickness of powder coating 50 micron)

Providing and fixing glazing in aluminium door, window, ventilator shutters and partitions etc. with EPDM rubber / neoprene gasket etc. complete as per the architectural drawings and the directions of engineer-in-charge . (Cost of aluminium snap beading shall be paid in basic item): With float glass panes of 4.0 mm thickness (weight not less than 10 kg/ sqm)

Galvanised wire mesh of average width of aperture 1.4 mm and nominal dia of wire 0.63 mm

With float glass panes of 5 mm thickness (weight not less than 12.50 kg/sqm)

Providing and fixing circular/ Hexagonal cast iron or M.S. sheet box for ceiling fan clamp, of internal dia 140 mm, 73 mm height, top lid of 1.5 mm thick M.S. sheet with its top surface hacked for proper bonding, top lid shall be screwed into the cast iron/ M.S. sheet box by means of 3.3 mm dia round headed screws, one lock at the corners. Clamp shall be made of 12 mm dia M.S. bar bent to shape as per standard drawing.

Providing and laying water proofing treatment in sunken portion of WCs, bathroom etc., by applying cement slurry mixed with water proofing cement compound consisting of applying : (a) First layer of slurry of cement @ 0.488 kg/sqm mixed with water proofing cement compound @ 0.253 kg/ sqm. This layer will be allowed to air cure for 4 hours. (b) Second layer of slurry of cement @ 0.242 kg/sqm mixed with water proofing cement compound @ 0.126 kg/sqm. This layer will be allowed to air cure for 4 hours followed with water curing for 48 hours. (The rate includes preparation of surface, treatment and sealing of all joints, corners, junctions of pipes and masonry with polymer mixed slurry.)

Water proofing for Old and Now Roof Slab • Providing and laying water proofing treatment on roof slab by applying two Component, factory designed, ready to use, acrylic modified flexible material applied wth brush, roller or spray for water proofing coating as Per ....Mier specificatIons with following steps (a)surface preparation -Providing and cleaning o1 concrete ...lece le remove dust, oil, grease including removal of existing loose paint r coating, and cement laitance by cleaning with comer..ed air 8 water let including all materials, labour, tools complete Ponding test to be done after plugging all outlets and to be checkedtrodentify seepage eakage On identification of seeps cem t be done with non shrink expanding admixt e a Ind, t 1MYK c g / Dr Fout/Fosroc or equive teems such as those betwe be chamfered with 15 1 41 admixed with ac Fixit or equivalent slum, of acrylic concretein base rovtartg and repaving of all c arapet wall and the roof slab et 50 mm fillet of mortar (Cement sand mer of Sika/ Fosroc/MYK SchomberglDr chamfering a prime coat shall be given with the Repairing surface irregularities, damaged ad cracks if any, with an acrylic polymer modified repair moile, including a coat of bonding agent of the same with cement slurry inctC01; all material, labour, tools complete (b)1st Coat - APOrlit coat of two component acrylic modified, ready to use. flexible come s material on surface saturated dry roof and inside wall of Par ll upto 600 mm by brush or roller After 1st coat re. pgplaisesd c@lot,h5t: kla9y,sw,nheincothaet rost, itahyee r of application , 45 still green 1st coat purpose of measure he entire treated surface will be measured "4, (c) 2nd Coat -To apply g02 coat of two component acrylic rnorAdmir* ready to use, flexible come' tonal right angle to the 140,af,•:,-- over the glass fibre laid surface*d alepld be * applied VW Sgmt/coat For the purpose of rnikeSCiretfleritthe entireteaterfstiface will be measured " After three days of drying the 2nd coat , the rain water outlets to be plugged and ponding test to be done for 48 hours to identify seepage, leakage from soffit and found necessary rectification to be done as per satisfaction of E/C The waterproof coating to be protected from damage before screed over it Water proofing Brand - Sika Topseal 109hi / Fosroc Brushbond RI". Dr Feet Picliflin 2K 1 MYK Actuate' TG Product Performance Chemical Base F'. A Acrylic copolymer, Part B: Specially graded cementitious powder -D011,4 1.6 fief, (mixed density) at 427°C Tensile Strength -2 N/mm2 atter 28 days (with Fibre cloth) (According to ASTM D 2370) Pullout Bond Strength -2 N/mm2 (concrete failure) (According to ISO 4624) Slant-Shear Bond Strength -4 N/mm2 (According to FIP 5 15) Elongation at Break -35% without Fibre Cloth and 20% with Fibre Cloth (According to ASTM D 2370) (d) Protection of treated surface with PCC •- The treated surface should be covered with 25mm/50mm PCC of M-20 grade(1.1.5 3) with proper slope ( 1 120) towards the rain outlets in alternatepanels of 2 mt x 2mt keeping 6 mm gap between the panel joint Integral water proofing admixture conforming to IS 2645 @ of 100 ml per bag of of cement to be added in the screed concrete (paid separately for this items) All corners shall be chamfered with 150mm X 150 mm fillet The rainwater outlets shall be just leveled with the screed concre toe ure smooth discharge of water - the peripheral gaps be en p pi o and concrete surface should be packed pro with n c e and tiurpheral mouth to be sealed with ure Pvt Ltd. / MYK Schomb Fixit/Fosroc For the purpose of measurement the ed surface will be measured " ensitive epoxy putty o (e)Groove of PC should be filled with Polysulphide Sealant. (Paid Separate* d - Sika India Pvt Ltd / MYK Schomberg / Dr FixitiFosroc W for five years

Covering of treated surface with PCC .- Providing 25 mm thick Cement Alf, Concrete M20 1:1. :3) maintaining slope in alternate 2 mt x 2 mt panels with aaprove. of stone chips of 20 mm to 6 mm size graded and cleaned sand 2.5 to 3 including screening,shuttering,and mixing cement concret . fixer with admixture of integral water proofing and placing in posi . ing curing,taxes and royality all complete as per building specifi nd direction of Ell. Panels that has been left shoul be casted next dysThere should be 6 mm gap between Panels .Brand Sika _Plastocrate Aus,MYK proof WP10, Fosroc- Conplast X421 lc& Dr Fixit Pidiproof LW+

Providing and mixing liquid integral water proffing compound in conctrete of plaster as manufacturer specification and as per direction of engineer in charge. Brand. Sika plastocrate plus, MYK proff WP 10, Fosroc-Conplast x 4211C, Dr.Fixit, Pidiproff LW+ or Equivalent

Providing and filling of 6 mm thick Groove between 25 mm PCC Panels with Polysulphide Sealant (Poring Grade)as Per drawings and technical specifications and direction of E in Charge (with 18% GST Polysulphicle Fosroc-Thoflex 600.Dr Fixit Pidiseal PS(42P) !MraYndK -Seikaal PS or Euivalent

Providing and fixing of expansion joint system related with floor location as per drawings and direction of Engineer-In-Charge. The joints system will be of extruded aluminum base members, self aligning / self centering arrangement and support plates etc. as per ASTM B221-02. The system shall be such that it provides floor to floor /floor to wall expansion control system for various vertical localtion in load application areas that accommodates multi directional seismic movement without stress to it's components. System shall consist of metal profiles with a universal

aluminum base member designed to accommodate various project conditions and finish floor treatments. The cover plate shall be designed of width and thickness required to satisfy projects movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self- centering arrangement that freely rotates / moves in all directions. The Self - centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement and flexure in all directions including vertical displacement. Provision of Moisture Barrier Membrane in the Joint System to have watertight joint is mandatory requirement all as per the manufactures design and as approved by Engineer -in- Charge. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system related with wall joint (internal/external) location as per drawings and direction of Engineer-In- Charge. The joints shall be of extruded aluminum base members, self aligning / centering arrangement and support plates as per ASTM B221- 02. The material shall be such that it provides an Expansion Joints System suitable for vertical wall to wall/ wall to corner application, both new and existing construction in office Buildings & complexes with no slipping down tendency amongst the components of the Joint System. The Joint System shall utilize light weight aluminum profiles exhibiting minimal exposed aluminum surfaces mechanically snap locking the multicellular to facilitate movement. (Material shall confirm to ASTM 6063).

Providing and fixing of expansion joint system of approved make and manufactures for various roof locations as per approved drawings and direction of Engineer-In-Charge. The joints shall be of extruded aluminum base members with, self aligning and self centering arragement support plates asper ASTM B221-02. The system shall be such that it provides watertight roof to roof/roof to corner joint cover expansion control system that is capable of accommodating multidirectional seismic movement without stress to its components. System shall consist of metal profile that incorporates a universal aluminum base member designed to accommodate various project conditions and roof treatments. The cover plate shall be designed of width and thickness required to satisfy movement and loading requirements and secured to base members by utilizing manufacturer’s pre-engineered self-centering arrangement that freely rotates / moves in all directions. The Self centering arrangement shall exhibit circular sphere ends that lock and slide inside the corresponding aluminum extrusion cavity to allow freedom of movement

Providing & fixing UV stabilised fiberglass reinforced plastic sheet roofing up to any pitch, including fixing with polymer coated 'J' or 'L' hooks, bolts & nuts 8mm dia. G.I plain/bitumen washers complete but excluding the cost of purlins, rafters, trusses etc. The sheets shall be manufactured out of 2400 TEX panel rovigs incorporating minimum 0.3% ultra-violet stabiliser in resin system under approximately 2400 psi and hot cured. They shall be of uniform pigmentation and thickness without air pockets and shall conform to IS 10192 and IS 12866.The sheets shall be opaque or translucent, clear or pigmented, textured or smooth as specified.

2 mm thick corrugated (2.5" or 4.2" or 6") or step-down (2" or 3" or 6" ) as specified

Providing and supplying aluminium extruded tubular and otheraluminium sections as per the architectural drawings and approvedshop drawings , the aluminium quality as per grade 6063 T5 or T6as per BS 1474,including super durable powder coating of 60-80microns conforming to AAMA 2604 of required colour and shade asapproved by the Engineer-in-Charge. (The item includes cost ofmaterial such as cleats, sleeves, screws etc. necessary forfabrication of extruded aluminium frame work. Nothing extra shallbe paid on this account).

Designing, fabricating, testing, protection, installing and fixing in position semi (grid) unitized system of structural glazing (with open joints) for linear as well as curvilinear portions of the building for all heights and all levels, including:

a) Structural analysis & design and preparation of shop drawings for the specified design loads conforming to IS 875 part III (the system must passed the proof test at 1.5 times design wind pressure without any failure), including functional design of the aluminum sections for fixing glazing panels of various thicknesses, aluminium cleats, sleeves and splice plates etc. gaskets, screws, toggles, nuts, bolts, clamps etc., structural and weather silicone sealants, flashings, fire stop (barrier)- cum-smoke seals, microwave cured EPDM gaskets for water tightness, pressure equalisation & drainage and protection against fire hazard including:

b) Fabricating and supplying serrated M.S. hot dip galvanised / Aluminium alloy of 6005 T5 brackets of required sizes, sections and profiles etc. to accommodate 3 Dimentional movement for achieving perfect verticality and fixing structural glazing system rigidly to the RCC/ masonry/structural steel framework of building structure using stainless steel anchor fasteners/ bolts, nylon seperator to prevent bimetallic contacts with nuts and washers etc. of stainless steel grade 316, of the required capacity and in required numbers.

c) Providing and filling, two part pump filled, structural silicone sealant and one part weather silicone sealant compatible with the structural silicone sealant of required bite size in a clean and controlled factory / work shop environment , including double sided spacer tape, setting blocks and backer rod, all of approved grade, brand and manufacture, as per the approved sealant design, within and all around the perimeter for holding glass.

d) Providing and fixing in position flashings of solid aluminium sheet 1 mm thick and of sizes, shapes and profiles, as required as per the site conditions, to seal the gap between the building structure and all its interfaces with curtain glazing to make it watertight.

e) Making provision for drainage of moisture/ water that enters the curtain glazing system to make it watertight, by incorporating principles of pressure equalization, providing suitable gutter profiles at bottom (if required), making necessary holes of required sizes and of required numbers etc. complete. This item includes cost of all inputs of designing, labour for fabricating and installation of aluminium grid, installation of glazed units, T&P, scaffolding and other incidental charges including wastages etc., enabling temporary structures and services, cranes or cradles etc. as described above and as specified. The item includes the cost of getting all the structural and functional design including shop drawings checked by a structural designer, dully approved by Engineer-in-charge. The item also includes the cost of all mock ups at site, cost of all samples of the individual components for testing in an approved laboratory, field tests on the assembled working structural glazing as specified, cleaning and protection till the handing over of the building for occupation. In the end, the Contractor shall provide a water tight structural glazing having all the performance characteristics etc. all complete as required, as per the Architectural drawings, as per item description, as specified, as per the approved shop drawings and as directed by the Engineerin-Charge.

Note:- 1. The cost of providing extruded aluminium frames, shadow boxes, extruded aluminium section capping for fixing in the grooves of the curtain glazing and vermin proof stainless steel wire mesh shall be paid for separately under relevant items under this subhead. However, for the purpose of payment, only the actual area of structural glazing (including width of grooves ) on the external face shall be measured in sqm. up to two decimal places.

Note:-2. The following performance test are to be conducted on structural glazing system if area of structural glazing exceeds 2500 Sqm from the certified laboratories accreditated by NABL(National Accreditation Board for Testing and Calibration Laboratories), Department of Science & Technologies, India. Cost of testing is payable separately. The NIT approving authority will decide the necessity of testing on the basis of cost of the work, cost of the test and importance of the work. Performance Testing of Structural glazing system Tests to be conducted in the NBL Certified laboratories

1. Performance Laboratory Test for Air Leakage Test (-50pa to – 300pa) & (+50pa to +300pa) as per ASTM E-283-04 testing method for a range of testing limit 1 to 200 mVhr” 2. Static Water Penetration Test. (50pa to 1500pa) as per ASTME- 331- 09 testing method for a range up to 2000 ml.” 3. Dynamic Water Penetration (50pa to 1500pa) as per AAMA 501.01- 05 testing method for a range upto 2000 ml” 4. Structural Performance Deflection and deformation by static air pressure test (1.5 times desing wind pressure without any failure) as per ASTME- 330-10 testing method for a range upto 50 mm” 5. Seismic Movement Test (upto 30 mm) as per AAMA 501.4-09 testing method for Qualitative test” Tests to be conducted on site 6. Onsite Test for Water Leakage for a pressure range 50 kpa to 240 kpa (35psi) upto 2000ml”

Extra for openable side / top hung vision glass panels (IGUs) including providing and supplying at site all accessories and hardwares for the openable panels as specified and of the approved make such as heavy duty stainless steel friction hinges, min 4 -point cremone locking sets with stainless steel plates, handles, buffers etc. including necessary stainless steel screws/ fasteners, nuts, bolts, washers etc. all complete as per the Architectural drawings, as per the approved shop drawings, as specified and as directed by the Engineerin- Charge.

Providing and supplying Spandrel Glass Panels comprising of 6 mm thick heat strengthened monolithic float glass of approved colour and shade with reflective soft coating on surface # 2 of approved colour and shade so as to match the colour and shade of the IGUs in the vision panels etc. ,all complete for the required performances as specified, as per the Architectural drawings, as per the approved shop drawings, as specified, and as directed by the Engineer- in-Charge. For payment, only the actual area of glass on face # 1 of the glass panels (but excluding the area of grooves and weather silicone sealant) provided and fixed in position, shall be measured in sqm.(Payment for fixing of Spandrel Glass Panels in the curtain glazing is included in cost of relevent Item*). (i) Coloured tinted float glass 6mm thick substrate with reflective soft coating on face # 2, having properties as visible Light transmittance (VLT) of 25 to 35%, Light reflection internal 10 to 15%, light reflection external 10 to 20%, shading coefficient (0.25- 0.28) and U value of 3.0 to 3.3 W/m2 degree K etc. The properties of performance glass shall be decided bytechnical sanctioning authority as per the site requirement.

Steel work in built up tubular (round, square or rectangular hollow tubes etc.) trusses etc., including cutting, hoisting, fixing in position and applying a priming coat of approved steel primer, including welding and bolted with special shaped washers etc. complete. Hot finished welded type tubes

Clearing jungle including uprooting of rank vegetation, grass, brush wood, trees and saplings of girth up to 30 cm measured at a height of 1 m above ground level and removal of rubbish up to a distance of 50 m outside the periphery of the area cleared.

25 mm wooden planking, tongued and grooved in flooring, including fixing with iron screws complete with : Second class teak wood

Providing and fixing M.S. angle 50x50x5 mm to act as nosing with lugs of M.S. flat 10x5 mm, 10 cm long, forked at end 60cm apart (minimum three lugs to be provided), including necessary welding and applying a priming coat of approved primer on exposed surface etc. complete.

Providing and fixing tiled false ceiling of specified materials of size 595x595 mm in true horizontal level, suspended on inter locking metal grid of hot dipped galvanized steel sections ( galvanized @ 120 grams/ sqm, both side inclusive) consisting of main "T" runner with suitably spaced joints to get required length and of size 24x38 mm made from 0.30 mm thick (minimum) sheet, spaced at 1200 mm center to center and cross "T" of size 24x25 mm made of 0.30 mm thick (minimum) sheet, 1200 mm long spaced between main "T" at 600 mm center to center to form a grid of 1200x600 mm and secondary cross "T" of length 600 mm and size 24x25 mm made of 0.30 mm thick (minimum) sheet to be interlocked at middle of the 1200x600 mm panel to form grids of 600x600 mm and wall angle of size 24x24x0.3 mm and laying false ceiling tiles of approved texture in the grid including, required cutting/making, opening for services like diffusers, grills, light fittings, fixtures, smoke detectors etc. Main "T" runners to be suspended from ceiling using GI slotted cleats of size 27 x 37 x 25 x1.6 mm fixed to ceiling with 12.5 mm dia and 50 mm long dash fasteners, 4 mm GI adjustable rods with galvanised butterfly level clips of size 85 x 30 x 0.8 mm spaced at 1200 mm center to center along main T, bottom exposed width of 24 mm of all T-sections shall be pre-painted with polyester paint, all complete for all heights as per specifications, drawings and as directed by Engineer-in-charge

12.5 mm thick fully Perforated Gypsum Board tile made from plasterboard having glass fibre conforming to IS: 2095 part I, of size 595x595 mm, having perforation of 9.7x9.7 mm at 19.4 mm c/c with center borders of 48 mm and the side borders of 30 mm, backed with non woven tissue on the back side, having an NRC (Noise Reduction Coefficient) of 0.79, with 50 mm resin bonded glass wool backing.

Providing and fixing on wall face unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion, (i) Single socketed pipes. 110 mm diameter

Providing and fixing on wall face unplasticised - PVC moulded fittings/ accessories for unplasticised Rigid PVC rain water pipes conforming to IS : 13592 Type A, including jointing with seal ring conforming to IS : 5382, leaving 10 mm gap for thermal expansion.

Bend 87.5° 110 mm bend

Shoe (Plain) 110 mm Shoe

Providing and fixing unplasticised -PVC pipe clips of approved design to unplasticised - PVC rain water pipes by means of 50x50x50 mm hard wood plugs, screwed with M.S. screws of required length, including cutting brick work and fixing in cement mortar 1:4 (1 cement : 4 coarse sand) and making good the wall etc. complete. 110 mm

Making khurras 45x45 cm with average minimum thickness of 5 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate of 20 mm nominal size) over P.V.C. sheet 1 m x1 m x 400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 coarse sand) and a coat of neat cement, rounding the edges and making and finishing the outlet complet

Providing 250mm wide brick drain in cement mortar (1:6) with av. 150mm clear depth and 125mm apron including cost of earthwork involved with 75mm cement concrete (1:4:3) over one brick designation 75A flat soling in proper grade and slope at the base the drain duly plastered in C.M. (1:3) with punning over exposed surface all complete as per building specification and direction of E/I.

Making plinth protection 50mm thick of cement concrete 1:3:6 (1 cement : 3 coarse sand (zone - III) : 6 graded stone aggregate 20 mm nominal size) over 75mm thick bed of dry brick ballast 40 mm nominal size, well rammed and consolidated and grouted with fine sand, including necessary excavation, levelling & dressing & finishing the top smooth.

Preparation and consolidation of sub grade with power road roller of 8 to 12 tonne capacity after excavating earth to an average of 22.5 cm depth, dressing to camber and consolidating with road roller including making good the undulations etc. and re-rolling the sub grade and disposal of surplus earth with lead upto 50 metres.

Granular Sub-Base with Coarse Graded Material ( Table:- 400- 2) (Construction of granular sub-base by providing coarse graded material, spreading in uniform layers with motor grader on prepared surface, mixing by mix in place method with rotavator at OMC, and compacting with vibratory roller to achieve the desired density, complete as per clause 401) (i) for grading- I Material

Cast in Situ Cement Concrete M20 kerb (Construction of cement concrete kerb with top and bottom width 115 and 165 mm respectively, 250 mm high in M 20 grade PCC on M-10 grade foundation 150 mm thick, foundation having 50 mm projection beyond kerb stone, kerb stone laid with kerb laying machine, foundation concrete laid manually, all complete as per clause 408)

Excavation in Soil with Dozer with lead upto 100 metres (Excavation for road way in soil by mechanical means including cutting and pushing the earth to site of embankment upto a distance of 100 metres (average lead50 metres), including trimming bottom and side slopes in accordance with requirements of lines, grades and cross sections.)

Supplying materials and labours for constructing inspection chamber of designation class 75 B bricks size 750 mm deep, 600 x 450 internal dimension having 250 mm wall thickness in cement mortar ( 1:6 ) including 12 mm cement plaster ( 1:4 ) with punning on inside and cement plaster (1:6 ) with 600 x 475 mm G.I. cover with frame (Weight not less than 36 Kg.) in foundation and refilling all complete as per specification and direction of E/l.

Dry stone pitching 22.5 cm thick including supply of stones and preparing surface complete.

Welded steel wire fabric fencing with posts of specified material and of standard design placed and embedded in cement concrete blocks 45x45x 60 cm of mix 1:5:10 (1 cement:5 fine sand : 10 graded stone aggregate 40 mm nominal size), every 15th post, last but one end post and corner post shall be strutted on both sides and end post on one side only and struts embedded in cement concrete blocks 70x45x50 cm of the same mix, provided with welded steel wire fabric fixed between the posts fitted and fixed with G.I. staples on wooden plugs or tied to 6 mm bar nibs with G.I. binding wire (cost of posts, welded steel wire fabric, painting, earth work in excavation and concrete to be paid for separately).

Providing and fixing concertina coil fencing with punched tape concertina coil 600 mm dia 10 metre openable length ( total length 90 m), having 50 nos rounds per 6 metre length, upto 3 m height of wall with existing angle iron 'Y' shaped placed 2.4m or 3.00 m apart and with 9 horizontal R.B.T. reinforced barbed wire, stud tied with G.I. staples and G.I. clips to retain horizontal, including necessary bolts or G.I. barbed wire tied to angle iron, all complete as per direction of Engineer-in-charge, with reinforced barbed tape(R.B.T.) / Spring core (2.5mm thick) wire of high tensile strength of 165 kg/ sq.mm with tape (0.52 mm thick) and weight 43.478 gm/ metre (cost of M.S. angle, C.C. blocks shall be paid separately)

Sand - 8 km

Chips - 22 km

Boulder-10 km

Stone Metal-22 km

Brick - 7+1 km

Flyash - 15 km

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site.

(a) From 0.00 M to 50.00 M below G.L.

(b) From 51.0 M to125.00 M

(c) From126.0 M to150.00 M

Supplying, assembling, lowering and fixing in vertical position in bore well, unplasticized PVC medium well casing (CM) pipe of required dia, conforming to IS: 12818, including required hire and labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer -in-charge. 200 mm nominal size dia

Development of tube well in accordance with IS : 2800 (part I) andIS: 11189, to establish maximum rate of usable water yield withoutsand content (beyond permissible limit), with required capacity aircompressor, running the compressor for required time till well isfully developed, measuring yield of well by "V" notch method or anyother approved method, measuring static level & draw down etc. bystep draw down method, collecting water samples & getting testedin approved laboratory, i/c disinfection of tubewell, all complete,including hire & labour charges of air compressor, tools & accessoriesetc., all as per requirement and direction of Engineer-in-charge

Providing and fixing suitable size threaded mild steel cap or spot welded plate to the top of bore well housing/ casing pipe, removable as per requirement, all complete for borewell of: 200 mm dia

Providing and fixing M.S. clamp of required dia to the top of casing/ housing pipe of tubewell as per IS: 2800 (part I), including necessary bolts & nuts of required size complete. 200 mm clamp

Supplying 100mm dis submersible pump sets confirming to 8034 and motor confirming to IS 9283 pump shall be suitable for various delivery head and discharge with stainless steel pump shaft and polypropylene/noryl impeller. Motor suitable for working on 415 + 10, 3HP, 50 Hz, AC supply with cable guard, thurst carbon/fiber bearing to withstand entire hydraulic thurst, water proof winding shall be provided. The pump set shall be suitable for diret coupling Pump shall have suitable outlet as per manufacturers design. Anti thurst stream lined non return valve shall be provided with pump, 3 meter submersible copper conductor cable in single/double run shall be provided with each pump. Submersible pump set 100mm dia (with Polypropylene/Noryl Impeller) up to 20 stages 5 HP

Supplying fitting and fixing 3 crore 4 sqmm Flat copper submersible cable FINOLEX / HEVELS make including all taxes ,royalty etc all complete job as per direction of E/I.

Supply fitting and fixing lowering 40 mm dia G.L. collumn pipe - do - do - all complete job as per direction of E/I.

Point Wiring in PVC Conduit, with Piano type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with piano type switch, phenolic laminated sheet, suitable size of GI box etc as required. Group-A

Point Wiring in PVC Conduit, with Piano type Switch: Wiring for light point/ fan point/ exhaust fan point/ call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in surface/recessed PVC conduit, with piano type switch,phenolic laminated sheet, suitable size of GI box etc as required. Make-Havells/ Legrand/ Polycab/ C&S/ Hager/ABB / HPL . Group-B

Wiring for Light point/fan point/exaust fan point/call bell point with 1.5 sq.mm FR PVC insulated copper conductor single core cable in recessed PVC conduit, with modular type switch , Modular plate, suitable G.I boxes and earthing the point with 1.5 sq.mm FR PVC insulated copper conductor single core cable etc. as required . Group-C

Wiring for power plug with 2x4 sqmm FR PVC insulated copper conductor single core cable in recessed PVC conduit alongwith 1 No. 4 sq. mm FR PVC insulated copper conductor single core cable for loop earthing as required.

Circuit / Sub-main wiring in PVC Conduit: Wiring for circuit / sub-main wiring along with earth wire with the following sizes of PVC insulated, copper conductor, single core cable in surface/recessed PVC conduit as required.

2x1.5 Sqmm + 1x1.5 sqmm earth wire

2x2.5 Sqmm + 1x2.5 sqmm earth wire

2x4 Sqmm + 1x4 sqmm earth wire ( Industrial socket)

2x6 Sqmm +1x6 sqmm earth wire-PDB

4x6 Sqmm + 2x6 sqmm earth wire

4x10 Sqmm + 2x10 sqmm earth wire

TV cable in Existing Conduit: Supplying and drawing co-axial cable RG-6 grade copper conductor, PE insulated with PVC sheath in the existing surface/ recessed PVC conduit as required.

S/F Piano type Switch / Socket: Supplying and fixing following piano type switch / socket on the existing switch box including connections etc as required.

5/6 AMPS, one way switch

5/6 Amps, 3 pin socket outlet

TV antenna socket outlet

Electronic step fan regulator, mini

S/F Modular type electronic fan regulator: Supplying and fixing stepped type fan regulator on the existing modular plate switch box including connections but excluding modular plate etc as required.

Supplying and fixing Modular type blanking plate-Supplying and fixing modular blanking plate on existing modular plate switch box excluding modular plate etc. as required.

Supply and Fixing Light Plug Point with Piano Type Accessories: Supply and Fixing GI/ PVC box on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 3 pin, 5/6 amps modular socket outlet and 5/6 amps modular type switch, connection, painting etc as required.

Supply and Fixing Light Plug Point with Piano Type Accessories: Supply and Fixing GI box on surface or in recess with phenolic laminated sheet cover in front including providing and fixing 6 pin, 15/16 amps modular socket outlet and 15/16 amps piano type switch, connection, painting etc as required.

Supply & fixing 20A SPN MCB Industrial Socket Outlet: Supply and fixing of 20A, 240V, SPN insustrial type socket outlet with 2 poles and earth, metal enclosed plug top along with 20 amps 'C' series, SP MCCB, in sheet steel enclosure, on surface or in recess with chained metal cover for socket out let and complete with connections, testing and commissioning etc as required. Make : L&T/ABB/Legrand/Polycab/Philips

Providing & fixing : Porviding and fixing of MV danger notice plate of 200mmX150 mm, made of mild steel at least 2mm thick and vitreous enamelled white on both sides and with inscription in single red colour on front side as required.

S/F light plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fixing 3 pin 5/6 amps modular socket outlet and 5/6 amps modular switch. corutection, painting etc. as required (For light plugs to be used in non residential buildings)

S/F power plug point with modular type accessories :- Supplying and fixing suitable GI box with modular plac and cover in front on surface of in recess, including providing and fxing 6 pin 15/16 amps modular socket outlet and l5/16 amps modular switch. connection, painting letc. as required (For light plugs to be used in non residential buildings) L&T/ABB/Legrand/Polycab/Philips

Ceiling Rose: Supplying and fixing 3 pin,5 amp ceiling rose on existing junction box/wooden block including connection etc as required.

S/F Batten Holder: Supplying and fixing batten/angle holder including connection etc. as required.

Erection on Incandescent light fitting : Erection of wall bracket/ ceiling fittings of all sizes shapes containing upto two GLS amps per fittings complete with all accessories including connection etc. as required.

S/F Dingdong Call bell: Supplying and fixing electronic musical call bell suitable for D.C/A.C, single phase 230 volt, complete as required.

ITC fluorescent fitting directly on surface :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, directly on ceiling / wall, including connection with 1.5 Sq. mm. FR PVC insulated, copper conductor.

ITC fluorescent fitting with down rods :- installation testing and commissioning of Pre - wired, fluorescent fitting / compact fluorescent fitting of all types, complete with all accessories and tube etc, including supply & fixing ball and socket arrangement , 2 nos down rods of 20mm dia steel conduit upto 30cm. connection with 1.5 Sq. mm. FR PVC insulated, copper conductor.

Sff Extra down rod :- Providing and fixing extra conduit down rod of 20mm dia2 x lOcm length wiring with 2 x L5mm FR PVC insulated , copper conductor. Single core cable includingpainting etc. as required .(Note th'er5 cm length shall be rounded to the nearest 10 cm and 5 cm of less shall be ignored

ITC Ceiling Fan :- Installation, testing and commissioning of ceiling fan, including wiring the down rods of standard length (Up to 30 cm) with 1.5 sq. mm. FRPVC insulated,copper conductor,single core cable etc, as required.

Numbering of Fan/ fittings: Numbering of ceiling fan/ exhaust fan/ fluorescent fitting as required.

ITC Exhaust Fan upto 450 mm sweep: installation of exhaust fan upto 450 mm sweep in the existing opening, including making the hole to cut the size of the above fan, making good the damage, including connection, testing, commissioning etc as required.

S/F MCCB in cubical panel board: Supply and fixing following rating & capacity 4pole MCCB in existing cubicle panel board. Including drilling holes in panel, making connections etc as required.

25 to 100A, 16kA fixed thermal rating( to be used as incomer for light & UPS SDB as floor, wall mounted panel)

125A, 16kA fixed thermal rating( to be used as incomer for tap off bay of rising mains)

160A, 35kA fixed thermal rating( to be used as incomer for SDB as floor wall mounted panel)

200A, 35kA-(5 nos )fixed thermal setting with spreader links( to be used as incomer for tap off box of rising mains & 1 no for UPS room SDB)

Supplying and fixing SP MCB DB: S/F of the follwing way single pole and neutral sheet M.C.B distribution board, 240 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator). 8 way Double door

Supplying and fixing the follwing way Three Pole pole and Neutral Sheet steel M.C.B distribution board, 415 volts in recess, completed with tinned copper busbar, neutral bus bar, earth bus bar, din bar, hinged front acrylic cover from MCB Knob detachable gland plate, interconnection including earthing etc. as required(without MCB/RCCB/Isolator).

4 way(4+12) Double door Horizontal type

6 way(4+18) Double door Horizontal type

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

6/32A Single Pole

6/32A Double Pole(L)

40A Double Pole(L/P/UPS)

63A DP MCB for kitchen

32A TPN MCB ( LIGHTING)

40A TPN MCB ( FOR UPS DB)

50/63A TPN MCB (POWER)

Supply fixing(S/F) following sizes of medium class PVC Conduit along with accesseories in surface/recess including cutting the wall and making good the same in core recessed conduit etc. as required.

S/F Modular type Switch / Socket: Supplying and fixing following modular type switch / socket on the existing modular plate and switch box including connections but excluding modular plate etc as required.

5/6 AMPS, one way switch

5/6 Amps, 3 pin socket outlet

MV Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed, 1100V grade with Termination and Laying of cable. Make:- ( Havells/KEI/RR Kabel/Polycab/Phinolex)

2 Core 10 Sq mm

PVC/ XLPE Armoured Al Cable: Supply of following PVC/XLPE insulated PVC sheathed, heavy duty , armoured electrical cable with aluminium conductor for working voltage upto and including 1.1 kV grade( Confirms to IS :1554, part-1).

3.5CX25 sq. mm armoured AL Cable.

3.5CX70 sq. mm armoured AL Cable.

3.5CX95 sq. mm armoured AL Cable.

50mm dia, medium class GI pipes

65 mm dia, medium class GI pipes

Excavation and refilling of above mentioned medium class GI pipes

Copper Earth Plate Elecrode:- Earthing with copper plate 600mmx 600mmx 3mm thick including acessories and providing masonary enclosure with cover plate having locking arrangement and watering pipe etc with charcoal or cock and salt complete etc. as required.

S/L of 6 SWG earth wire in ground :- Supplying and laying of 6 SWG GI wire at 0.5mm metre below ground level for conductor earth electrode including soldering welding etc. as required.

S/L 8 SWG copper wire in ground :- Supplying and laying 8SWG copper wire at 0.50 metere below ground level for conductor earth electrode, including soldering etc. as required.

Supplying and laying 25mmx5mm GI earth strip in Ground: Supplying and laying 25mmx5mm GI earth strip at 0.50 metre below ground as strip earth electrode, including soldering etc as required.

Supplying and laying 25mmx5mm GI earth strip in surface/ recess: Supplying and laying 25mmx5mm GI earth strip on surface or in recess for connections etc as required.

Supplying and laying on wall, testing and commissioning of following capacity Air Insulated Compact type Bus Trunking for use in 415V, 3ph,50Hz, 4 wire AC supply with metal clad enclosure made of 1.6mm thick steel sheet duly powder coated in convient sections complete with 4 nos Al bus bars, necessary joints, elbow joints & expansion joints, fire barrier at each floor, provision of tapping at every metre, continious earthing with 2 nos Al strip of suitable size and other acessories etc as required.( make Legrand/ Siemens/ GE)

400A, 30kA SC for 1 sec-for essential riseing mains

630A, 50kA SC for 1 sec- for normal rising mains

Supplying and laying connecting to existing Air Insulated Compact type Bus Trunking / rising mains, testing and commissioning of following capacity Plug In/ Tap Off Box for use in 415V, 3ph,50Hz, 4 wire AC supply with 1.6mm thick steel sheet enclosure duly powder coated with provision of MCCB( but without MCCB) complete etc as required.( make Legrand/ Siemens/ GE)

125A 15kA SC for 1 sec

200A, 25kA SC for 1 sec

Supplying and laying testing and commissioning of following capacity TPN Tap Off Box made of 1.6mm thick steel sheet enclosure duly powder coated with existing rising mains complete with TPN disconnector FSand HRC fuses, connections, earthing etc as required.

Supplying ,installaing, connecting to existing to existing Air Insulated Compact type Bus Trunking/ rising mains testing and commissioning of End Feed Unit for use in 415V, 3ph,50Hz, 4 wire AC supply made of 1.6mm thick steel sheet duly powder coated with provision of MCCB/ACB (but without MCCB/ACB) complete with all necessary accessories.(Suitable for bus arrangement for multi-run Al cable termination) ( make Legrand/ Siemens/ GE)

400A, 30kA SC for 1 sec-for essential riseing mains

630A, 50kA SC for 1 sec- for normal rising mains

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 kV grade of following size on wall surface as required.

upto 35 sq.mm( clamped with 1mm thick saddle)

Above 35 sq.mm and upto95 sq.mm( clamped with 25x3mm MS flat clamp)

1.1kV Cable End Termination: suppluing and fixing indoor cable end termination with brass double compression gland and AL lugs of following sizeAl armoured cables.

3.5Cx25 sq.mm

3.5Cx70 sq.mm

3.5Cx95 sq.mm

Floodlights 80W :Environmental friendly, new generation,aesthetically designed, ultra modern LED floodlight luminaire with high diecast housing and IP66 protection.( make Havells/Bajaj-BJFL 80W LED/ Philips/ Wipro)

Supply of Ceiling Fan: Supplying and fitting of 1400 mm Sweep regular/ standared model AC ceiling fan , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton Greaves / Havells / Orient/ Philips

Supply of BLDC Ceiling Fan: Supplying and fitting of BLDC 5 Star, 32W, 1200 mm Sweep AC ceiling fan , including connection with 1.5 sq mm copper wire, down rod of standared length(upto 30cm) withall accessories as required. Make :- Polar/Bajaj/Crompton / Havells / GEC.

Supply of Exhaust metal Fan: Supply and fitting of 230mm, 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required. Make :- Polar/Bajaj/Crompton Greaves / Havells / Orient/ Philips

Supply of Metal Exhaust Fan 12"(300mm): Supply of 12"(300mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

Supply of Metal Exhaust Fan 15"(380mm)(for Kitchen): Supply of 15"(380mm), 230V AC metal exhaust fan in the existing opening including making good the damage, connection testing, commissioning etc as required.Make :- Polar/Bajaj/Crompton Greaves / Havells / Orient/ Philips

Supply of Wallmounted Fan: Supply of 16"(400mm), 230V AC wall/cabin fan including fixing the bracket, making , connection testing, commissioning etc as required( Make- Polar/Bajaj/ Havells/Crompton)

LED tube with Batten 20W/22W : Supplying and fixing of wall mounted LED 20W /22W tube + batten and electronic driver and accessories as required. ( Make -Wipro/Bajaj / Havells/ Philips)

LED Bulb 9W/10W : Supplying and fixing of LED 9W /10W bulb and accessories as required. ( Make -Bajaj / Havells/ Philips)

LED Floodlights 150W :Environmental friendly, new generation,aesthetically designed, ultra modern LED floodlight luminaire with high diecast housing and IP66 protection.( make: Wipro /Havells/Bajaj/ Philips)

Bulk head 9/10 LED Fitting: Supply and fixing of 9/10W LED, surface mounted bulk head PVE water proof housing for indoor/ ourdoor.( Make-Havells /Bajaj/Wipro/Philips)

Recess mounted 20W LED round :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness 20W LEDs as light source.( make : Havells /Bajaj/ Wipro/Crompton)

Panel 36W LED(2'x2') :Environmental friendly, new generation,aesthetically designed, ultra modern recess mounting luminaire with high brightness SMD LEDs as light source, suitable for Armstrong/Grid ceiling.( make : Havells /Bajaj/ Philips)

Supplying and fixing DP MCB Isolator(40Amps) : Supplying and fixing of double pole,240V, isolator in existing MCB DB complete with connections, testing and commissioning etc. as required.

LED Surface mounting 15W : Supplying and fixing of LED 15W surface mounting round down light and accessories as required. ( Make -Bajaj-model BGSLO SLEEK 15W / Havells/ Philips/ Wipro/Crompton)

Downlighter(Surface) 18W LED: Supply erection and commissioning of LED 18W, sleek surface-mounted, round LED downlight for soft diffused lighting and all accessories as required. ( make Havells/ Baja-BGSLO 18 WH / Philips)

Supply and Fixing testing and commissioning of Vertical Type TPN Sub-Distribution Board(SDB) with sutable for upto 160/125/100/63A FP MCB as incomer & single/ three ph outgoing MCBs(TP) IP-43 protection double door factory fabricated wall mounting type in surface/ recess powder coated, 41V, 200A Copper bus bar, earth & neutral bar, removiable gland plates, cable glands including connections with outgoing feeders complete all respect with LED indicator etc as required.( but without MCCBs & MCBs)

4 ways(8+12 ) Double door, Vertical type

S/F 'C' series SP MCB: Supplying and fixing 240 volts, 'C' series, miniature circuit breaker suitable for inductive loads of following poles in the existing MCB DB complete with connections, testing and commissioning etc, as required.

25-32A TPN MCB

50/63A TPN MCB ( For incomer in SDBs and outgoing of UPS room SDBs)

S/F 4P MCCB: Supplying and fixing 425 volts,MCCBs of thermomagnetic release with spreader links & rotary handle complete including conections testing and commissioning etc as required to be used in end feed box of rising mains. Make- Legrand-DPX3/ Schneider-NSX/ Siemens.

630A, 36kA, 4P MCCB

400A, 36kA, 4P MCCB

Providing of PVC/ XLPE insulated sheathed heavy duty armoured power cable with aluminium conductor of 1.1kV (confirming to IS-1554 part-1) Make-Havells/ Finolex/ Polycab.

2Cx6 sq.mm ( from feeder pillar to main gate light)

4Cx10 sq.mm ( from feeder pillar to Bollard and Street light)

3.5Cx35 sq.mm (Main LT panel to Lift machine panel, pump house & capacitor bank)

3.5Cx70 sq.mm (Main LT panel to outdoor feeder pillar)

3.5Cx95 sq.mm (Main LT panel to UPS room SDB nd fire pump panel)

3.5Cx300 sq.mm (Main LT panel to End feed box of 630A normal rising mains(2 runs), End feed box of of 400A Essential rising mains(1 run) to DG (in run) & to APFC panel(1 run)

3.5Cx400 sq.mm ( transformer to Main LT panel(2 runs))

Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 1.1 kV grade of following size direct in ground including excavation, sand cushioning protective covering and refilling the trench etc as required of following sizes.

upto 25 sq.mm

upto 95 sq.mm

upto 400 sq.mm

upto 400 sq.mm in same trench: Laying and fixing of one number additional PVC insulated and PVC sheathed/ XLPE power cable of 1.1 kV grade , exceeding 120 sq.mm but not exceeding 400sq.mm direct in ground in the same trench in one tier horizontal formation including excavation, sand cushioning protective covering and refilling the trench etc as required of following sizes.

11 kV Cable Laying: Laying and fixing of one number PVC insulated and PVC sheathed/ XLPE power cable of 11 kV grade of size not exceeding 120 sq.mm direct in ground including excavation, sand cushioning protective covering and refilling the trench etc as required.

Supplying and fixing Rewireable DP/TPN Switch Disconnector(SFU): S/F of the follwing way double pole / TPN sheet metal switch discooector fuse unit in existing metal board with rewireable type fuses, includin drilling holes in metal board, making connections etc as required. It will be wall mounted.( for Pump motor) Make- Havells/ Standared/ HPL

S/F Bus Bar Chamber: Supplying and fixing the follwing capacity busbar chamber with 4 strips of suitable size made of copper, heavy duty complete with all accessories including connections, earthing the body etc. as required.

S/L 25 x 5mm GI earth strip in Ground: Providing and fixing 25mmx5mm GI earth stripat 0.5 m below ground as earth electrode including soldering etc. as required.

Erection of Steel Pole upto 10m in CC: Erection of steel tubular pole of ;ength exceeding 8.0m but not exceeding 10.0m in cement concrete 1:3:6( 1cement:3coarse sand: 6 draded stone aggregate 40mm nominal size) foundation including excavation and refilling etc as required.

1.1 kV Cable End Termination: Supplying and making indoor cable end termination with brass double compression gland and aluminium lugs for following sizes of PVC insulate SLPE Al. Ar Cable:

2CX6 sq.mm ( Outdoor feder pillar to main gate light)

4CX10 sq.mm( outdoor feeder pillar to Bollards and steel tubular poles)

3.5CX35 sq.mm(Main LT panel to Lift machine panel, Pump house pane and Capacitor bank)

3.5CX70 sq.mm(Main LT panel to outdoor feeder panel)

3.5CX95 sq.mm(Main LT panel to UPS SDB and Fire pump)

3.5CX300 sq.mm(Main LT panel to Normal main rising and essential main rising box, and DG, APFC))

3.5CX400 sq.mm( transformer to Main LT panel )

11 kV Cable End Termination: Supplying and making outdoor cable end jointing with cast resin compound , lugs and other jointing materials for 3 core XLPE Al. Ar Cable:

Supplying , laying and fixing following dia GI pipe (medium class) in ground complete with GI fitting inclusing trenching (74cm deep) and re-filling etc as required.

7.0m height Octagonal Hot -dip glavinized pole(BOP-7030) :Supply, installation of 7.0m height OctagonalHot -dip glavinized pole with top dia 70mm, bottom dia 130mm & made of 3mm thick sheet, base plate dimension 200x200x12mm(L X B X T) including suitable sizes of foundation bolt all complete as required.( without arm) Make_Bajaj/Havells/Surya/ Philips

0.5m single arm suitable for 70mm top pole

0.5m double arm suitable for 70mm top pole

Supply and fixing of 45W LED street light fitting ,with die cast aluminium housing of ingress protection of IP65 and complete with all accessories etc on pole including connection and earthing the body etc as required. Make- Wipro/Bajaj/ Philips/ Havells.

Erection of metalic Pole of following length in cement concrete 1:3:6 ( 1 cement:3 coarse sand : 6 graded stone aggregate 40mm nominal size) foundation including excavation and refilling etc as required.

Gate Light for Main Entrance :- Providing and fixing, connection of intergal post top lamp for gate light 40W LED post top made in cast aluminium with decorative opal polycarbonate diffuser with IP:65 protection including all other accessories as per drawing provided at the time of work execution or as per the direction of E/I) (Wipro/Philips/ Havells / Bajaj-BGCL 40W LED )

LED Bollard Light: Providing anf Fixing of LED Bollard light decorative luminaire light fixture & LED lamp with foundation, commissioning, testing along with civil work with all other accessories as per drawing. Make- Bajaj-BGBOS 600 9W LED/ Wipro/ Havells/

HT Cable:- Supply of ISI marked aluminium cable conductor XLPE PVC insulated cable as per IS:7098 armoured, served, sheathed 11000 volt grade. Make:- Finolex / Polycab / Havells / KEI/RR Kable

3.5 x 70 Sq mm, 11KV XLPE / PVC Al. Ar. Cable

S/F Modular boxes , base & cover plate(Gang Box): SITCing and fixing following size / modules GI box along with modular base & cover plate for modular switches in recess etc as required.

1 or 2 module (78 mm x 78 mm x 45 mm)-for voice and data outlet.(Make- Legrand/Panduit/Ortronics)

S/F PVC/ GI Boxes: Supplying and fixing following size PVC/GI box on surface or in recess with suitable size of phenolic laminated sheet cover infront including painting etc as required.

72 mm X 146 mm X 48 mm deep

75mmX75mmX50mm deep

Supplying and fixing of following sizes of medium class PVC conduit along with accessories in surface/recess includingcutting the wall and making good the same in case of recessed conduit as required. Preffered Make- AKG/NORPACK/Polycab/Dauphin

Supplying and drawing of UTP 4 pair CAT 6 LAN Cable in the existing surface/ recessed Steel/ PVC conduit as required

2 Run CAT6 UTP Cable (for Network only . (Make:Legrand/Panduit/RIT/Siemon)

Detailed Spec for Cat 6 UTP PVC Cable

4 Pair Cable with integral cross -member pair separator for uniform characteristic impedance.

Category 6 Unshielded Twisted 4 Pair 100 Ω cable shall be compliant with ANSI/TIA/EIA-568-C.2-1 Additional ISO/IEC 11801:2010 (Ed. 2.2) and ISO/IEC 61156-5

Suitable for 10GBase-T applications in acc. with IEEE 802.3an up to 500 MHz and 55 m.

Transmission Performance Specification for 4 Pair 100Ω Category 6 Cabling

Category 6 UTP cables shall extend between the work area location and its associated telecommunications closet and consist of 4 pair, UTP CM cable jacket.

Conductor: Solid Copper

Conductor Diameter: 0.555+-0.01mm (23AWG)

Insulator HD Polyethylene solid

Jacket: PVC RoHS complied

Outer Diameter: 6.0 ± 0.2mm

Max Temperature: -20°C to +70°C

Should be ETL certified, UL Listed

Should have Pulling force of 11.5Kg.

Bend Radius: Installation: <4 X Cable Diameter at –20°C ±1°C, Operation: <4 X Cable Diameter at –20°C ±1°C

Conductor Resistance : <9.38Ω /100m

Resistance Unbalance 5% Max

Mutual Capacitance : < 5.6nF/100m

Capacitance Unbalance : 330pF/100m.

Propagation Velocity : 69%

ELT certified for 4 Channel should be submitted along with bid submission

Supplying and drawing following pair 0.5 mm dia FRLS PVC insulated annealed copper conductor, unarmored telephone cable in the existing surface/ recessed steel/ PVC conduit as required

2 Pair (Make: Polycab/ Finolex/ Deltron/Havells/Anchor/Molex/Schenider)

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l. 580mm. long - with 12.5litre low level PVC cistern

Supplying, fitting and fixing 40 mm high viterous white glazed earthen ware E.W.C. with "p" trap of Parry Hindustan or any other I.S.S. make including supplying & fixing 15 litres C.I. mosquito proof low down flushing cistern of approved make with complete fittings with C.I. handle and R.S. or bracket with telescopic flush pipe with brass coupling and plumbers joints spindle stop cock of approved quality weight not less than 450 grms. , 15 mm P.V.C. alkathene pipe 45 cm long with brass coupling at both ends and white/ black plastic solid state seal and lead of commander/ cuckoo or other I.S.S. make with hinges or screw etc. painting pipe and cistern etc. with 2 coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) With "P" trap (a)10 lit. low level PVC Cistern

Supplying, fitting and fixing viterous white glazed earthen ware I.W.C. of Parry Hindustan or any other I.S.S. approved make with 100 mm H.C.I., "p" trap 15 litres C.I.. or C. pull and let go flushing cistern of names or other I.S.S. equivalent make, complete with all fittings, C.I. or C.C. brackets 32 mm alkathene/P.V.C. telescopic flush, pipe about 2 M long with one brass coupling and clamps G.I. chain and pull including supplying and fixing a pair of viterous white glazed earthenware where footrest to be fixed in floor 15 mm C.I. body brass spindle stop cock of weight not less than 50 grms. 15 mm P.V.C. connection pipe 450 mm long and the exposed pipe and cistern with two coats of approved paint over a coat of red oxide primer etc. all complete as per specification and direction of E/l.(A) 580 mm long (c) with 10 lit. low level P.V.C. cistern

Supplying, fitting and fixing flat back or angular, lipped front viterous white glazed earthenware urinal of "Hindustan" " Parry" or any other approved I.S.S. make with all fittings with C.I. or R.S. brackets, standard size G.I. flush pipe with fitting clamps, 15 mm C.I. body brass spindle stop cock of approved quality weight not less than 400 grms. , 15 mm P.V.C. alkathene pipe 450 mm long with brass coupling at both ends and doing plumber joints including painting of exposed part with 2 coats of approved paint over a priming coat of red oxide, cutting wall and floor, making good the same etc. all complete as per specification and direction of E/l.(b) Standinq corner(600mmx350mm)

Supplying, fitting and fixing viterous white glazed earthen ware wash hand basin of Parry or Hindustan or any other I.S.S. approved make supported on pointed c.l. or R.S. brackets 32m C.I. brass waste 15mm dia C.I. body brass spindle stop cock of approved quality of weight not less than 350grms., 32mm P.V.C. waste pipe 750mm long with brass coupling at one end and making plumber joints etc. all complete as per specification and direction of E/l.

Providing and fixing Gun metal full way valve of approved qualtiy, all complete as per specification and direction of E/l

(b) 20mm dia and weiqht not less than 400gms.

(c) 25mm dia and weiqht not less than 500gms.

(d) 32mm dia and weiqht not less than 700qms

(e) 40mm dia and weight not less than 1.0 Kg..

Providing and fixing brass / C.I. Stop cock of approved quality all complete as per specification and direction of E/l .

Cutting chajja or cornice for laying G.I pipe and restoring the same with R.C.C (1:2:4) brick work in cement mortar (1:4) and cement plaster (1:4) as per specification and direction of E/l.

Making holes in walls for laying G.I pipes and restoring the same after pipe laying as per specification and direction of E/l

Cutting drain width wise above G.L. for laying H.C.I, pipe and restoring brick work in cement mortar (1:4) 12 mm cement plaster in (1:4) with neat cement punning as per specification and direction of E/l.

Making holes in wall for laying H.C.I, pipe and restoring the same after pipe laying as per specification and direction of E/l.

Supplying all tools and labours and cutting chajja, cornice, for laying H.C.I, pipes and making good the same as per specification and direction of E/l.

Supplying , Fitting and fixing bathroom fitting of approved make and as per IS specification all complete as per direction of E/I (all rates have been adopted from the basic rate from SOR + 15% for labour and contractors profit)

Pillar cock (long neck)

Bib cock - long thread

Piller Cock (ISI)

4- way diverter for conceled fitting

Glass shelf

Fluse valve complete with 32mm size control cock & flange

32mm dia. PVC waste pipe 750mm long with coupling

15mm C.P nipple with coupling

Steel jali - 100mm dia.

Providing and fixing Sink Cock eith Swinging casted spout

Providing Solvent cement

Supplying, fitting and fixing Mirrors of 6mm thick plate glass bevelled edge mirror including C.P brass revolving fittings 3mm ply wood board and C.P hinges to fix with mirror. 600X450mm

Supplying, fitting and fixing C.P. brass towel rail 20mmX600mm with bracket container

Supplying, fitting and fixing C.P. brass soap dish container medium quality with screw and hinges etc.

Providing and fixing Pressure adjustable shower with revoving joint

Providing and fixing 15mm dia and 45cm long PVC connection pipe with heavy qulity brass coupling at both ends etc all complete as per specification and direction of engineer in charge

Supplying, materrials and labour for constructing inspection chamber of designation class 75B brick size 750mm deep, 600X450mm internal dimension having 250mm wall thickness in cement mortar (1:6) including 12mm cement plaster (1:4) with punning on inside and cement plaster (1:6) with 600X475mm G.I. cover with frame (weight not less than 35kg) alongwith earth work in excavation and 80mm thick PCC (1:3:6) in foundation and refilling all complete as per specification and direction of E/I.

Providing and fixing C.P. brass bib cock of approved quality conforming to IS 8931, 15mm dia nominal bore of approved brand C.P. fittings

Providing and fixing C.P.brass long body bib cock of approved quality conforming to standard and weight not less thain 690gms.:15 mm nominal bore.

Providing and fixing C.P. brass Stop Cock (concealed) of standard designand of approved make conforming to IS 8931 15mm nominal bore, approved brand C.P. fittings.

Providing and fitting C.P. brass angle vale basin mixer and geyer points of approved qulity confirming to IS 8931 15mm nominal bore approved brand C.P. fittings

Providing and fixing PTMT/ C.P. swivelling shower,15mm nominal size, 95mm long, 65mm dia. of approved quality, color & make weighing not less than 40 gms with approximate 80 holes of 1.2 mm dia.

Providing and fixing PTMT Soap Dish Holder having length of 138 mm breadth 102 mm, height of 75mm with concealed fitting arrangements, Weighing not less then 106 gms.

Providing and fixing wash basin with C.I. brackets, 15 mm C.P. brass pillar taps, 32 mm C.P. brass waste of standard pattern,including painting of fittings and brackets, cutting and making good the walls wherever require :Falt back wash basin size 630X450 mm with a single 15mm C. P. pillar tap.

Providing and fixing Stainless Steel A ISI 304 (18/8) kitchen sink as per IS: 13983 with C.I. brackets and stainless steel plug 40 mm, including painting of fittings and brackets, cutting and making good the walls wherever required : Kitchen sink with drain board 510x1040 mm bowl depth 178 mm

Providing And fixing 32 mm waste pipe for sink or wash basin including P.V.C. waste fittings complete.

Providing and fixing Mirror of superior glass (of approved quality) and of required shape and size with plastic moulded frame of approved make and shade with 6mm thick hard board backing.Circular shape 450 mm dia

Providing and fixing c.p. towel ring complite with brackets fixed to wooden cleats with c.p.brass screws with concealed fitting arangement of approved qualite colour and make.(Mark or equipment)

Providing and fixing PTMT grating of approved quality and colour. 125 mm nominal dia with 25 mm waste hole

Providing and fixing unplasticised P.V.C. connection pipe with PTMT Nuts, collar and bush of approved quality and colour. 15 mm nominal bore with 45 cm length

Providing and fixing PTMT extension nipple 15mm size with 12" BSP thread 70mm lenth and 30mm breadth and weighing not less than 32gms of approved make

Providing and fixing Chlorinted Polyvinyl Chloride (CPVC) pipes, having thermal stability for hot & cold water supply including all CPVC plain & brass threaded fittings i.e fixing the pipe with clamps at 1Mtr. Spacing. This includies jointing of the pipes & fittings with one step CPVC solvent cement and the cost of cutting chases and making good the same including testing of joints complete as per direction of E/I. Concealed work including cutting chases and making good the walls etc.

15mm nominal bore

20mm nominal bore

25mm nominal bore

32mm nominal bore

External work -25mm dia

External work -32 mm dia.

External work - 40mm nominal bore

provding and laying of 110mm dia. P.V.C. pipe for outlet of water to outlet drain including all accessories ,I.e lubricants, solventcement, clamp, ring, sockets etc.(SUPREME S.W.R.)

Providing & fixing on wall face unplasticised - Rigid P.V.C. pipes conforming to IS: 13592 Type A including jointing with seal ring conforming to IS: 5382 leaving 10mm gap for thermal expansion. Single socketed pipes. 110mm dia

Providing & fixing on wall face unplasticised - P.V.C. Mouluded fitting/ accessories for unplasticised- P.V.C. rain water pipe confirming to IS: 13592 TYPE A, including jointing with seal ring confirming to IS: 5382 leaving 10mm gap for thermal expansion, (i)

Single Tee with door

Bend 87.5 degree

110 mm bend

Marking khurras 45x45 cm. with average minimum thickness of 55 cm cement concrete 1:2:4 (1 cement : 2 coarse sand : 4 graded stone aggregate 20 mm nominal size) over PVC sheet 1mx1mx400 micron, finished with 12 mm cement plaster 1:3 (1 cement : 3 fine sand) and a coat of neat cement, roundingthe edges and making and finishingthe outlet complete

Constructing brick masonary road gully chamber 50x45x60 cm with bricks of class designation 75' in cement mortar 1:4 (1 cement :4 coarse sand) including 500x450 mm precast RCC horizontal grating with frame complete as per standard design.

Providing and placing on terrace (at all floor levels) polyethylene water storage tank, IS : 12701 marked, with cover and suitable locking arrangement and making necessary holes for inlet, outlet and overflow pipes but without fittings and the base support for tank

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Supplying and fixing PVC fitting of approved make confirming to IS: 1729 including supplying nails and bobbins, fixing solution including earth work or masonary work cutting and remarking and providilding as the case may be all complete as per specification and direction of E/I

PVC plain bend 100mm dia.

PVC plain bend 100mm dia.

Floor trap - 100mm dia.

Ring rubber

Door piece

Providing and laying non-pressure NP2 class (light duty) R.C.C. pipes with collars jointed with stiff mixture of cement mortar in the proportion of 1:2 (1 cement : 2 fine sand) including testing of joints etc. complete : 150 MM dia R.C.C. pipe

Providing and laying non- pressure NP2 class ( light duty ) R.C.C. pipes with collars jointed with still mixture of cenent mortar in the proportion of 1:2 ( lcement : 2 fine sand ) including testing of joints etc. complete. 450 mm dia. R.C.C. pipe metre

Supplying, assembling, lowering and fixing in vertical position in bore well unplasticized PVC medium well screen (RMS) pipes with ribs, conforming to IS: 12818, including hire & labour charges, fittings & accessories etc. all complete, for all depths, as per direction of Engineer-in-charge. 100 mm nominal size dia

Supplying and fixing C.I. cover without frame for manholes : 500 mm diameter C.I. cover (medium duty) the weight of the cover to be not less than 58 kg

Cost of Driling 200 mmx165mmx125 mtr.deep bore well in all kind of Soil and rock in rural area for instalation of pump set with Hydrolic DTH Rig machine all complete including all materials, tools,driling rig,air compressureand equipmentsas well as fule, lubricantsand cost of transportation of rig machine annd other vehical up to Site. (a) From 0.00 M to 50.00 M below G.L.

Supplying, filling, spreading & leveling stone boulders of size range 5 cm to 20 cm, in recharge pit, in the required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge.

Supplying, filling, spreading & leveling gravels of size range 5 mm to 10 mm, in the recharge pit, over the existing layer of boulders, in required thickness, for all leads & lifts, all complete as per direction of Engineer-in-charge

Making soak pit 2.5 m diameter 3.0 metre deep with 45 x 45 cm dry brick honey comb shaft with bricks and S.W. drain pipe 100 mm diameter, 1.8 m long complete as per standard design. With common burnt clay F.P.S. (non modular) bricks of class designation 7.5

Telephone RJ11 socket outlet(Make- Legrand/Panduit/Ortronics)

Chemical Earthing Supply, errection, fitting, fixing, commissioning and testing along with earth cutting, digging, earth refilling for chemical earthing of the building except G.I. Strips (25mmX5mm) Each earth pit has to be tested with earth tester 1000 V/1000 Ohms & the test report has to be submitted by the contractor to the department after certification of the same by the consultant. The above chemical earthing includes the provision of masonary enclosure and HDPE Earth Pit Cover 300mm X 300 mm (Under-floor earth inspection pit) having locking arrangement as earth chamber.The above chemical earthing includes the following items (3 Mtr Earthing)

Each chemical earthing shall have following details:-

Supply of Pollution free Earthcon Compound 4 bags of 25 Kg each

Supply of 17.2 mm dia, 250 micron,molecularly bounded copper coated 3 Mtr long electrode. Tested as per IEC 62561-2. Meets the requirement of IS 3043 & IEC 60364-5-54. Tested for short circuit withstanding capacity. High Tensile strength. (UL Listed).

Supply of Stainless Steel "U" Bolt Clamp

Supply of HDPE Earth Pit Cover for earth chamber (Capacity of 5 ton)

Supply, Installation, Testing and Commissioning of electric driven, horizontal type, single/multistage, end suction type, centrifugal pump of cast iron body, C.I impallers with carbon steel shaft & mechanical seal directely coupled with TEFC SQ cage foot mounted type induction motors suiitable for operation on 3 phase, 415 volts 50 Hz AC supply having flow rate of min 450 LPM and head of approx 40 mtrs complete in all respect as required or as directed by engineer incharge.

Main Fire Pump

Standby Deisel Engine Pump

Jockey Pump

Terrace Booster Pump

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Pump Room

Providing and fixing IS marked Gate Valve / Foot Valve (incase of -ve suction) complete with companion flanges, bolts, nuts, rubber insetions etc.

200 mm diameter

150 mm diameter

100 mm diameter

Providing and fixing IS marked butterfly valve (PN 1.6) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

200 mm diameter

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

80 mm diameter

100 mm diameter

150 mm diameter

Providing & fixing of pressure switch in M.S. pipe line including connection etc. as required.

Providing, laying, testing & commissioning of IS 1239 marked black M.S pipe including all fittings i.e bend, elbows, tees, flanges, reducing socket, nuts and bolts, gaskets etc fixed with welded / screwed joints. including necessary excavation, backfilling, removal of surplus soil etc. min. 1 mtr deep excavation and wrapping with anticorrosive treatement with 4 mm thick asphalt tape as per IS:10221, refilling the trench etc. OR fixed with screwed or welded joints, hanged with clamps, hanger supports, dash fasteners, bolts, nuts, rubber insertions etc including threading, cutting, welding, edge preparation, painting of approved colour over two coat of primer, cutting & making good the wall/ floor wherever required, complete as required or as directed by engineer incharge. Make:Tata/Nezone/Jindal

200 mm diameter

150 mm diameter

100 mm diameter

80 mm diameter

65 mm diameter

50 mm diameter

40 mm diameter

32 mm diameter

25 mm diameter

Providing and fixing S.S Fire Hydrant Valve of approved quality with 63 mm female, instant, ovlique, single outlet, 80 mm flanged inlet, brass spindle, cast iron wheel m A.B.S. blank cap and chain. conforming to IS: 5290 complete with companion flange, bolts, nuts, rubber insertion / compressed asbestos gasket etc. and painted in fire red colour.

Providing and fixing swinging, wall mounting type First Aid Hose Reel of approved quality and made from compresed steel sheet with dust cover, cast iron brackets including 30 m long, 19 mm nominal bore, high presure braided rubber hose as per IS:444 Type hose guide, PVC shut off nozzle with 6 mm outlet and 25 mm nominal bore gun metal inlet valve, bolts, nuts rubber insetion etc. painted in Fire red colour including cutting and making good the walls wherver required.

Providing and fixing in position 63 mm nominal bore and 15 m long synthetic fibre, CP fire hose pipe of approved make bearing IS: 636 -1988 type A mark and having TAC and MMD approved with a pair of 63 x 63 mm gun metal instantaneous type, heavy duty delivery hose coupling (conforming to IS: 903) bound and riveted to the hose pipe with copper rivets and copper wire complete.

Providing and fixing in position short SS brach pipe of approved quality with 63 mm male instatneous type inlet and 15 mm outlet nozzle complete conforming to IS : 903

Providing and fixing Standard response sprinklers (With Covers, white / ivory colour) with quartzoid bulb overating temperature 68 degree centgrade, of 15 mm orifice and k factor 80 (5,6) made out of forged brass and chrome finish. Make:Safex/Atasee/Tyco

Supplying, installation, testing & commissioning of sprinkler flexible pipe (UL Listed) of stainless steel complete with 15 NPT on reducer thread with maximum working pressure of 175 PSI test pressure of 875 PSI (Burst) with branch line (Inlet) 25mm NPT male thread to sprinkler head (Outlet) 15mm NPT female thread with reducer, nipple, 2 side brackets, center bracket, stockbar of following sizes complete as required.

Supplying, fixing, testing & commissioning of 1 set of 63mm two way instantaneous fire brigade connection (FBC) with inbuilt NRV comprising of SS and four SS instantaneous male inlet coupling confirming to IS:604 with plug and cap with chain as required with nut & bolts, washers, high pressure gasket as required.

Supplying, installation, testing and commissioning of optical type Smoke detector and mounting base with LED light complete as required. Make:Qutak/Honeywell/Seimens/Bosch

Supplying, installation, testing and commissioning of duel tone electronic hooter / Flasher / Strobe suitable for wall mounted complete as required. Make:Honeywell/Seimens/ Qutak/ Bosch

Supplying, installation, testing and commissioning of manual call box in suitable enclosure with arrangement to raise the alarm when the glass is manually broken complete as required. Make:Honeywell/Seimens/Qutak/Bosch

Supplying, installation, testing and commissioning of microprocess base main fire alarm control panel with LCD Display lights. The panels shall have 240 volts AC power supply automatic Battery charger 24 Volts sealed lead acid maintenance free battries as complete with batteries, battery charger illuminated numeric digram complete as required. Make:Honeywell/ Seimens/ Qutak/ Bosch

Jungle clearance in borrow area, building premises, flanks and slope on the road, canals and embankment by removing the grass and jungle bushes from the top including weeding out shrubs small trees upto 150 mm dia. and their removal all complete job as per direction of E/I.

Earth work in surface excavation not exceeding 30 cm in depth but exceeding1.5 m in width as well as 10 sqm on plan including disposal of excavated earth up to 50 m and lift up to 1.5 m, as per directions of Engineer in Incharge: All kinds of soil

Supply , stacking & filling of good earth at site including cost of royalty & carriage upto 5 Km ( Earth measured in stacks will be reduced by 20% for payment ) .

Supplying and stacking at site dump manure from approved source, including carriage up to 5 km (manure measured in stacks will be reduced by 8% for payment) : Screened through sieve of I.S. designation 20 mm

Rough dressing the trenched ground including breaking clods.

Uprooting weeds from the trenched area after 10 to 15 days of its flooding with water including disposal of uprooted vegetation

Fine dressing of the ground.

Spreading of sludge, dump manure and/or good earth in required thickness as per direction of officer-in-charge (cost of sludge, dump manure and/ or good earth to be paid separately).

Mixing earth and sludge or manure in the required proportion specified ordirected by the Officer-in-charge

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately) : Holes 90cm dia, &90cm deep

Providing and laying Neelgiri/Mexican grass turf with earth 50mm to 60mm thickness of existing ground prepared with proper level and ramming with tools wooden (Dhurmos) and than rolling the surface with light roller make the surface smoothen and light waterning with sprinkler and maintenance for 30 days or more till the grass establish properly, as per direction of officer-in-charge.

Complete maintenance of the entire garden features having as per yard stick in the garden area i.e. lawn trees, shrubs, herbs, edge, flower beds, foliages, creepers etc. including hoeing,weeding, pruning, replacement of plants, gap filling, watering, mowing of lawn, grass cutting by lawn mover and brush cutter, removal of garden waste, applying insecticide, pesticide & fertilizers(whenever required) top dressing of lawn with good earth and manure and maintenance of other garden related works as directed by office-in-charge (Cost of Good Earth, Manure, Fertilizer, Insecticide, Pesticide will be provided by the Department & lawn mover and brush cutter with fuel and other T & P material/articles shall be provided by the contractor.) and as per direction of officer in charge. Open spaces(1Mali for 3.00Acre).

Anti termite treatment by digging pits 30 cm deep and 4 cm dia, 6 to 7 holes around the tree using chemical emulsion at the rate of 1.5 liter per hole in two time or more application to get the trees free from termiteinfection chemicals used Chlorpyriphos 20% EC in the ratio of 1% concentration and as per direction of officer-in-charge.

Anti termite treatment of lawn area through premise 30.50% I P. one liter premise diluted in 499 liters water and applying solution @ 1.00 litre solution per sqm lawn or bed area.(two application) i/c cost of chemical)and as per direction of officer-in-charge.and as per direction of officer-in-charge.

Providing and Displaying Bamboo Buddha Valley with fresh & healthy 5 to 6 suckers 1.80 m to 2.10m ht umbrella type well developed in 50 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Bismarckia Palm 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus cirsnallis well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Cycus revoluta in 35 cm challi, specimen , having 30 to 40 with fresh and healthy, leaves having 25cm to 30cm circumfrance of base stem well developed as per direction of the officer-in-charge.

Providing and Displaying Ficus Long Island topiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Retusa topiary well developed with fresh & healthy 5 to 6 big ball specific size and shape 180 to 210cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Phoenix roebelenii palm well developed having 20 to 25 fresh & healthy leaves 90 to 105 cm ht. in 30 cm Cement Pot as per direction of the officer-in-charge..

Providing and Displaying Foxtail palm well developed with fresh & healthy foliage of ht. 210 to 240 cm in big 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Ficus Nuda well developed with fresh & healthy foliage from Top to Bottom with single piller 75 to 90 cm spread, 195 to 210 cm ht. in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Topiary of Ficus Panda well developed with fresh & healthy foliage with 3 to 4 Ball and 60 to 75 cm spread each Ball, 135 to 150 cm ht., in 35 cm Cement Tray /Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Travelers palm well developed with fresh & healthy leaves foliage 210 to 240 cm ht specimen in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Cassia fistula (Amaltash) of height 120-135 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Cassia javanica of height 120-150 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Delonix regia (Gulmohar) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.v

Providing and stacking of Grevillea robusta (Silver Oak) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Jacaranda mimosifolia of height 150-165 cm. In big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Millingtonia hortensis of height 150-165 cm. In big poly bag of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Peltophorum species of height 150-165 cm. In big poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Plumeria alba dwarf dwarf of height 90-105 cm. with 3-4 branches and thick stem in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Schleichera trijuga (Kusum) of height 150-165 cm. in big poly bags of size 25 cm as per direction of the officer-in-charge

Providing and stacking of Tabebuia sp. of height 150-165 cm. in big polybags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Alternanthera red/green species of height 15 cm to 20 cm, full of branches and foliage in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Duranta Golden, having ht.15 to 20 cm bushty shape with fresh and healthy leaves in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge..

Providing and stacking of Iresine herbstii, of height 20-25 cm. full of branches well developed in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ophiopogon jaburan ( variegated ),full of variegated leaves in Earthen Pot/Plastic Pot of size 20 cm. as per direction of the officer-in-charge..

Providing and stacking of Tradescantia, full of leaves in Earthen Pot/Plastic Pot of size 15 cm. as per direction of the officer-in-charge.

Providing and stacking of Wedelia trilobata,full of leaves in 15 cm size of Poly bags & as per direction of the officer-in-charge.

Providing and stacking of Tradescantia zebrina having in 15 cm size of Earthen Pot/Plastic Pot & as per direction of the officer-in-charge.

Providing and stacking of Ficus benjamina (green) of height 150-165 cm., bushy with healthy branches and lush green foliage in big size HDPE bags as per direction of the officer-in-charge.

Providing and stacking of Ficus blackii (F.vivion) (bushy) of height 150-165 cm. with 8-10 branches and healthy foliage in earthen pots of size 30 cm as per direction of the officer-in-charge.

Providing and Displaying Ficus Starlight with fresh, healthy and attractive foliage 45 to 60 cm spread 75 to 90 cm ht., specimen bushy ,in 35 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Gardenia jasminoides of height 45-60 cm. with 3- 4 branches in earthen pots of size 20 cm as per direction of the officer-in-charge.

Providing and stacking of Hamelia patens of height 60-75 cm. with 6-8 branches in poly bags of size 25 cm as per direction of the officer-in-charge.

Providing and stacking of Bougainvillea (Variety Butiana, Lady Mary Baring, Mahara,Mohan,Scarlet Queen, Variegated, Glabra Formosa, Peruviana Odissi, Paratha, Subhra,Thimma, Spectabilis L.N Birla, Refulgens) of height 30 cm. to 45 cm. with 2-3 branches in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Clerodendrum splendens of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Ipomoea purpurea (Morning glory) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Jasmine humile (Yellow) of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Quisqualis indicia of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Providing and stacking of Tecoma grandiflora of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge..

Providing and stacking of Vernonia elaegnifolia (curtain creeper) plant of height 30 cm to 45 cm. in 20 cm size of Earthen pots / Plastic pots & as per direction of the officer-in-charge.

Supplying and stacking of good earth at site including royalty and carriage up to 1 km (earth measured in stacks will be reduced by 20% for payment).

Supplying and stacking at site dump manure from approved source, including carriage up to 1.0 km (manure measured in stacks will be reduced by 8% for payment)

Screened through sieve of IS designation 20 mm

Screened through sieve of IS designation 16 mm

Screened through sieve of IS designation 4.75 mm

Supplying and stacking of well decayed cow dung manure at site including royalty and carriage up to 1.0 km (cow dung manure measured in stacks will reduced by 8% for Payment)

Fine dressing of the ground

Mixing earth and sludge or manure in the required proportion specified or directed by the Engineer-in-charge

Spreading of sludge, dump manure and / or good earth in required thickness as per direction of Engineer-in-charge (cost of sludge, dump manure and / or good earth to be paid separately).

Uprooting rank vegetation and weeds by digging the area to a depth of 60 cm, removing all weeds and other growth with roots by forking repeatedly, breaking clods, rough dressing, flooding with water, uprooting fresh growths after 10 to 15 days and then fine dressing for planting new grass, including disposal of all rubbish with all leads and lifts

Digging holes in ordinary soil and refilling the same with the excavated earth mixed with manure or sludge in the ratio of 2:1 by volume (2 parts of stacked volume of earth after reduction by 20% : 1 part of stacked volume of manure after reduction by 8%) flooding with water, dressing including removal of rubbish and surplus earth, if any, with all leads and lifts (cost of manure, sludge or extra good earth if needed to be paid for separately)

Holes 1.2 m diameter and 1.2 m deep

Holes 90 cm diameter and 90 cm deep

Holes 60 cm diameter and 60 cm deep

Holes 45 cm diameter and 45 cm deep

Azadirachta Indica (Neem)

Alstonia scholaris (Devil tree)

Ficus benjamina (weeping fig)

Bauhinia purpurea (Kachnar)

Callistemon lanceolatus( Bottle brush)

Delonix regia (Gulmohar)

Cassia fistula (Golden shower)

Plumeria alba(white champa)

Plumeria rubra(pink champa

foxtail palm

Buddha belly bamboo

Clerodendrum inerme(Volkameria inermis)

Ficus panda

Ficus benjamina Starlight (Ficus Starlight)

Gardenia jasminoides

Golden duranta

Hamelia patens

Hibiscus rosa-sinensis(udhul)

Raphis excelsa(lady palm)

Tecoma gaudichaudi(Yellow bells)

TMC dwarf(Chandani

Alternanthera red

Chlorophytum comosum

Jatropha

Sprenger's asparagus(Foxtail fern

Syngonium podophyllum(Syngonium butterfly

Tradescantia pallida

Cynodon dactylon(doob grass)

Stainless Steel Text (Text Height 250 mm ) at Pergola Slab with Grouting all Complete Including matrial & Labour as pet E/I

Providing and fixing of 3D Lite panel System of 22mm thick(minimum) with both the outer walls in clear color and middle cells shall have the alternate horizontal walls in co-extruded white or approved colour. Panels shall be fixed on purlins with Z type Stainless steel Fastener using minimum 3 self drilling screws. Panel shall be 600 mm wide manufactured with vertical standing Seams of 15- 20mm height at both sides of the panel(welding or gluing of upstanding seam is not acceptable). Panels shall be secured with snap on connectors to interlock the panels shall have 2-4 tooth locking system to ensure best performance against wind uplift or hurricane. Polycarbonate Panel system shall also include Aluminium profiles in natural mill finish for end closure. Panels should be manufactured in a manufacturing facility with approved quality assurance procedure as per ISO 9001 & ISO 14001. Panel manufacturer shall provide warranty against any manufacturing defects for a period of 10 years( min.) and should have a succe to be used. The above frames should be fixed to the concrete/ masonary walls and floor by means of self expanding screws panel shall be installed as per the approved drawing, specifications and as directed by the engineer-in-charge.

Fountain Equipment with all complete job as per specification and direction of E/I.

Larsen & Toubro 5 HP Starters Control Panel for Submersible Pump Larsen & ToubroR (5 HP)

Supplying Fixing Lift of Following Specificaion Jhonson or Eque. NEXTRA/ 8 PASSENGER LIFT/ 544 Kgs / 4 Floors / Stops / STAINLESS STEEL (1.5 mm) Car Cabin No. of Elevators-1 Nos. Elevator for your project at Garhwa Type & Capacity-Passenger – 08 Persons – 544 Kgs. (Neo) Speed-1 Mtr/Sec (approx.) Type of Drive-Variable Voltage Variable Frequency Drive with Microprocessor based Simplex Full Collective Control Type of Machine -Top - Gearless Machine - MRL Required Travel- 10 Meters. (max.) Serving -Ground to 3st Upper-Floor 4 -Stops, 4 -Levels,4- Openings Well Size.-1900 mm Wide x 1750 mm Deep (over Plaster) Power Supply-415 V three-phase 50 cycles alternating current Auxiliary Required-Single-phase 220 V 50 cycles alternating current Car Size (Clear Inside) approx.-1300 mm Wide x 1100 mm Deep Required Pit Depth-1600 mm. Required Head Room-4500 mm. Car Enclosure-Car Finish –Vandal Proof Flooring-PVC Flooring Electric Light-LED Light fitting Fan-400/300mm Sweep One Number No. of Entrances-One Location – Front. Car Entrance-Automatic Power Operated Center Opening Vandal Proof Stainless Steel Doors - with Vision Panel (290 X 590mm- Minimum). Landing Entrance-Automatic Power Operated Center Opening Vandal Proof Stainless Steel Doors - with Vision Panel (290 X 590mm- Minimum). Clear Opening-800 mm Wide x 2000 mm High. Indicators: Car & Landings-Direction & Position Indicator. Other Features-Battery Operated Emergency Light & Alarm Call Registration LED’s OSG Electronic Switch Infra-Red Light Curtain Door Safety Intercom System Handicap provision for Disable Persons Braille Buttons Fireman Drive - FRD Automatic Rescue Device – ARD Load Weight Device – LWD

Supply and fixing of PVC sheathed following conductor 1.1 KV grade armoured Cable of following sizes including making end termination with compression gland & bimetalic lugs, and support etc.complete as required

3 × 50 sq.mm.(aluminium)

3 × 10 sq.mm.(aluminium)

10 × 2.5 sq.mm.(Copper)

2 × 1.5 sq.mm. in Conduit

Supply, fitting, fixing, connecting and testing of 24-port 10/100/1000T and 100/1000 SFP combo stackable switch with 4 SFP+ ports and dual power supply, Switching Capacity 280Gbps and Forwarding Rate 214.3Mpps, 2GB DDR SDRAM, 256MB flash memory, Route maps and redistribution (OSPF, BGP, RIP), Supports up to 64K MAC addresses, SDN or similar kind of technolgy should support, Switch should support link reccovery within 50ms for Ring architecture, All switches, AP, FO Module , Access Points aand WLAN Controller should be from the same OEM, Warranty 5 year from Day 1. (Make:- Cisco - WS-C3850-24XS / Allied Telesis -Model No. AT-x930-28GSTX / Juniper - EX4300)

The above L3 Managed Data Switch consists of the following:-

1. Power cord India, right angle.

2. Both side Cable connector.

3. 1 year free service pack.

Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports

Switching Capacity/Forwarding Rate :- 280Gbps/214.3 Mpps

Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM

Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Routing:- IPv4 static routing and RIP.

Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability

IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6

Diagnostic:- Optical Digital Diagnostics Monitoring, Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN)

Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad

Operating Temparature:- 0°C to 50°C

Certification:-EMC: EN55022 class A, FCC class A, VCCI class A, ICES-003 class A Immunity: EN55024, EN61000-3-levels 2 (Harmonics), and 3 (Flicker) Safety-Standards: UL60950-1, CAN/CSA-C22.2 No. 60950-1-03, EN60950-1, EN60825-1, AS/NZS 60950.1,Certification: UL, cUL, TUV, (RoHS) Compliance-EU RoHS compliant,China RoHS compliant.Warranty:- 5 Years.

24 x 10/100/1000T ports and 4 x 100/1000X SFP ports, L2 Switch , Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, operating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24T-4G/ Allied Telesis - Model AT-x230-28G / Juniper - EX2200-24)

The above L2 Managed Data Switch consists of the following:-

1. Power cord India, right angle.

2. Both side Cable connector.

3. 1 year free service pack.

Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports

Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps

Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM

Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Routing:- IPv4 static routing and RIP.

Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability

IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6

Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN)

Operating Temparature:- 0°C to 50°C

Certification:- EN,UL and RoHS.Warranty:- 5 Years.

Supply, fitting, fixing, connecting and testing of switch with 24 x 10/100/1000T PoE ports and 4 x 100/1000X SFP ports, PoE+ L2 Switch , Switching Capacity 56Gbps and Forwarding Rate 41.7Mpps, Switch should support PoE and PoE+ with 370W minimum power budget, operaating temperature 0°C to 50°C, Switch should support link reccovery within 50ms for Ring architecture, SDN or similar kind of technolgy should support, Warranty 5 year from Day 1 . Make:- Cisco - WS-C9300L-24P-4G / Allied Telesis -AT-x230-28GP / Juniper - EX2200-24P)

The above L2 Managed Data Switch consists of the following:-

1. Power cord India, right angle.

2. Both side Cable connector.

3. 1 year free service pack.

Interface- 24 x 10/100/1000T ports and 4 x 100/1000X SFP ports

Switching Capacity/Forwarding Rate :- 56Gbps/41.7Mpps

Performance:- Up to 16K MAC addresses, 256MB DDR SDRAM

Management:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Security:- Console port, GUI, Telnet, SSH,SNMPv1,2 and 3, powerful centralized management and zero-touch device installation and recovery like SDN,

Routing:- IPv4 static routing and RIP.

Fail-over:- Switch capable of recovery within 50ms in a ring for application high availability

IPv6:- Device management over IPv6 networks with SNMPv6, Telnetv6, SSHv6 and Syslogv6

Diagnostic:- Optical Digital Diagnostics Monitoring,Automatic link flap detection and port shutdown,Port and VLAN mirroring (RSPAN)

Standard Protocol:- IEEE 802.1Q,IEEE 802.1w,IEEE 802.1s,IEEE 802.1p,IEEE 802.1AB,IEEE 802.1AX,IEEE 802.3ad

Operating Temparature:- 0°C to 50°C

Certification:- EN,UL and RoHS.Warranty:- 5 Years.

SITC of Gigabit Fiber Module-MM, Support up to 550mtr (Make:- Cisco - GLC-SX-MMD / Allied Telesis -Model No. GLC-SX-MMD/AT-SPSX/CTP-SFP-1GE-SX) / Juniper - CTP-SFP-1GE-SX)

OEM Criteria for Passive Networking items.

OEM must provide declaration on conformity of all the passive components to the following standards: a) TIA/EIA 568-2.D ; b) TIA/EIA 568-3.D ; c) ISO/IEC 11801

OEM must be a member in the TIA and BICSI organization. OEM shall have RCDD certified manpower in India for design support and validation. Certificate is Mandatory

OEM should have valid ISO 9001 and ISO 14001 certificate on Design, development and manufacture of SW and HW solutions for communication networks.

All the products must have RoHS Compliance and from One OEM

12 Port LIU Switch : SITC of 12 Port Loaded LIU with SC Unit for 6 MM fiber Multi mode fibres OM3 (2 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 12 Fiber Capacity & 12 Nos. of SC Pigtail - Pigtail 1 Meter MM OM3 (Make:Legrand/Panduit/RIT/Siemon)

24 Port LIU : SITC of 24 Port Loaded LIU with SC Unit for 24 MM fiber Multi mode fibres OM3 (4 Nos. of Loaded Duplex adapter with Adapter plate) along with 1 Pc of Splice Tray - 24 Fiber Capacity & 24 Nos. of SC Pigtail - Pigtail 1 Meter Multi Mode OM3 (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Fiber Optic LIU Rack Mount LIU (12/24 Ports)

Fiber optic patch panel : Fiber optic patch panel FMS Termination Drawer should have sufficient slots to accommodate 3 of 12/16 Port LC Adaptor Plates.

Should have Slide type drawer structure

Height: 1 U, 1.75 inches (12 & 24 Ports)

Material: Cold Rolled Steel in surface coated by electrostatic epoxy powder

Slots: FMS should have sufficient slots to accommodate adaptor plates

Empty Slots of FMS should be covered with blank plates.

Splice Tray : Splice Tray of ABS, Comply with UL 94V2 material should be supplied with LIU.

Detailed Specs for 12/16 Port LC/SC Type Adaptor Plates (MM OM3)

The adaptor plate should be pre-loaded with LC/SC Type Multi mode Duplex Adaptors.

Port Density :12/16 LC/SC Single mode Ports

All LC adapters should be duplex type with shutter for protection. Adapters should be snap mount for easy insertion and removal.

Insertion Loss: <0.2 to <0.1 dB

Compliance :RoHS Compliant

Detailed Specs for LC Type 9/125μm OM3 Fiber Optic Simplex Pigtail

Type : 9/125 micron fibre performance

Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2

Operating Temperature: -40°C to +75°C

Connector Insertion Loss: 0.30dB(Max)

Attenuation: 1310/1550 : 0.36/0.22 dB/KM

SITC of Fiber Duplex Patch Cords SC-LC MM-OM3 Patch Cord 2 mtr. (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Patch Cord, LC SC, Duplex, MM OM3, Bend Insensitive G651, PC, LSZH

Cable : LC/SC-SC/LC 50/125μm MM OM3 Multimode Duplex Patch Cord Length : 3mtrs

Connectors : The optical fiber patch leads shall comprise of Multi mode 50/125μm fiber with 2XLC type fiber connectors terminated at one end of fiber patch cord and 2xSC type connector at other end of the fiber patch cord

Insertion loss should be better than ≤ 0.30 dB

Jacket Material : LSZH complying to IEC 61034-1 & 2,IEC-60332-1, IEC-60754-1 & 2

Attenuation: 50/1300 : 3.0/1.0 dB/KM

Connector Loss : 0.30dB(max)

Operating Temperature : -40°C to +75°C

SITC of 6-Core OM3 MM Armoured Fibre Optics Cable in Mtrs: (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Outdoor F/O Cable, Loose Tube, MM OM3 – 1x6 Fibers, Central Steel rod with CST, PE

The fiber should be optimized for operation at 850 nm and at 1300 nm.

Should fulfill the requirements of ISO.IEC 11801 - 2nd Edition, type MM OM3, ITU-T REC G 651D spec IEC 60794-1-2 F5

No of Cores : 6/12

Max. Attenuation: At 850 nm <= 3.0 dB/km, At 1300 nm <=1.0 dB/km

Modal Bandwidth: At 850 nm: ≥1500 MHz.km, At 1300 nm: ≥500 MHz.km

Fibre/Tube Identification : Single Tube

Fibre protection (Tubes) : Polybutylene Terephthalate (PBT)

Armouring : CST

Outer Sheath : HDPE >2.0 mm

Pheripheral Strength Member: CST

Cable Diameter (D) : 8.8 ± 0.3 mm

Mass (Nominal) : 82 kg/km

Min. Bending Radius (during Installation) : 20 D;D-Outer Diameter

Max. Tensile Strength-Short Term : 1500N

Max. Crush Resistance-Short Term : 2200N

Operating Temperature range : -40°C to +70°C

SITC of 24 port UTP jack panel (24 port RJ-45 Loaded CAT-6 UTP 19" rackmountable patch panel preferbaly with 6 blocks). (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for 19" 1U 24 port unsheilded Patch Panel

Patch panel should be modular design, populates up to 24 UTP keystone-type jacks in 1U

Patch panel should be Enhanced with cable strain relief with retention tray; It should be single metal both front panel and rear tray

Material: sub-rack made of MS Steel with dimension 44.4 mm : 482.6 mm : 105 mm (h:w:d) tray

Information Outlet or connectin module should comply with the specification mentioned above in 2

Standard : Conforms to IEC-60603-7 (603-7) for keystone-type, snap-on apertures

Should be RoHS complied

SITC of Straight LAN Patch Chord-3 Mtr (Make:Legrand/Panduit/RIT/Siemon)

SITC of Straight LAN Patch Chord-1 Mtr (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Patch Cord, U/UTP 4P, Cat.6, length 1/3 Metre

Standardization: Compliant with Cat.6, Class E requirements: ISO/IEC 11801 2nd Edition Compliant with Cat.6 component standards IEC 60603-7-4 and 60603-7-5

Cable shield: U/UTP

Number of conductors : 8

Stranding: 7 x 0.20 mm (24 AWG)

Cable jacket characteristics: cable, metal-free

Cable overall diameter: 6.5±0.2 mm

Tube / Wire type: stranded conductor

Insulation: solid polyolefin, 0.97±0.02 mm diameter

Plug: Feature cable retension, with enhanced pull strength.

Cat 6 patch cord plug to have round cable holder and strain relief boot to avoid bending.

Jacket: PVC with 8 different color options

Plug should have high repeatability cross talk performance

SITC of white modular plate type Single front plate for 1 Nos. RJ 45 Data outlet (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Faceplate

Should be UK style Keystone-type Faceplates are available in 1, 2 & 4 port configurations

Should be featured with shutter options, the screws not to be visible

Should support Work with both Flush and Wall mount box

Should support Operating Temperature: -10～+60; Storage Temperature: -40～+68; Humidity: 10%~90% RH

Material: ABS, UL 94V-0; Spring: SUS304; Surface Finish: Polished

SITC of RJ 45 Data Module to be fixed on face plate (Make:Legrand/Panduit/RIT/Siemon)

Detailed Specs for Cat 6 UTP RJ 45 Keystone Jack

RJ45 Jack of Category 6, for the establishing of transmission channels of class E with up to 4 plugged connections, complies with Category 6 requirements of the standards ISO/IEC 11801:2nd edition, EN 50173-1, DIN EN 50173-1: 2002 as well as ANSI/TIA/EIA 568-B.2-1, de-embedded tested in acc. with IEC 60603-7 (603-7), interoperable and backwards compatible with Cat.5e and Cat.5.

Suitable for 10GBase-T applications in acc. with IEEE 802.3an up to 500 MHz and 55 m.

Compatible with RJ standard plugs (RJ11, RJ12, RJ45), PCB- and tool based connection of installation cables AWG 24 – 22 (0.5 mm – 0.65 mm) and flexible cables AWG 26/7 – AWG 22/7.

IDC termination should feature nil crossover in acc. with EIA/TIA 568-A/B, gold-plated bronze contacts for >750 mating cycles, >200 insertion cycle

Material: RoHS complied

Housing material: Polycarbonate (UL-94-V0)

Should be available with or without dust protection feature

Should be 3P certified

Splicing of Armoured SM/MM Fibre Optics Cable: Splicing, testing and commissioning of supplied, OFC cable of 6-Core Armoured Fibre Optics

SITC of Fully Loaded 15 U 19" 600*600 Wall Mounted Rack with all required accessories -2 Nos. of Fan,6A 6 Plug PDU-1 Nos. ,Cable Manager-2 Nos., Mounting Screws-20 Pcs ; Preffered Make-Legrand/APW/President/Valrack

Providing, fixing, fitting, installation and testing of 42 U Network Rack as server cabinet 19" LCS2 along with all standard accessories, 800mm (W), 1000mm (D), approx. Wt.150 Kg, CRCA 'D' grade 1.6mm thick sheet, pwoder coated for cabinet , 4mm Toughened Tinted Glass Door and along with following accessories:- 1. Cooling fan 220/230V AC, of 90 CFM-- 4 Nos. , 2. Cable manager Metal 4 Nos. 3. PDU- 230V /AC 1 No., le Channel 100mm wide. 2 Nos. 5. Heavy Duty Stationary Shelf 600mm(W)X475mm(D) - 1 No. , 6. Mounting Hardware (20 Sets of M-6 screws, washers, cage, nuts (Nickle Coated)- 3 Nos. ,7. Earthing strips copper 150mm H 1 No. 8. Door Lock 1 No. ,9. Caster Wheels (with breake) 2 Nos. 10. Caster Wheels (without breake) 2 Nos. ,11. Front Metal Band 1 No. (Make : Legrand /Schneider/Ortronics),(To be installed in centrelly located Server Room); Preferred Make-Valrack/President/Rittal

Main LT Panel for LIFT: - Supplying, designing, manufacturing, installation, testing, fitting, fixing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of panel of 16 SWG CRCA Sheet (1.6mm) CRCA sheet steel with dust and vermin proof with reinforcement of suitable size iron channel, fully compartmentalized cubical type, IP-43 wall mounted, totally enclosed suitable for operation on 415V, 50Hz, 3Ph, AC supply and fault level 25 kA .

Make-C&S/ Legrand-DPX3/ Schneider-NSX/ Siemens/L&T.

Incomer

63A, 25kA FP MCCB -1 no.

Outgoings

40A 10kA FP MCB "C' series-2 nos

32A 10kA DP MCB "C' series-2nos

Digital Ammetesr (0-600A)-3 phase, class:o.5 . Make :- AUE / Universal / L&T / Esma.

Digital Voltmeter (0-500V)-3 phase, class:o.5 . Make :- AUE / Universal / L&T / Esma.

Advanced New Generation ESE (Early Streamer Emission) Air Terminal Lightning Conductor:

Supply and Fixing testing testing of and commissioning of ESE technology lightning arrestor of type DMSGI-45 with Level-1 protection of 63m radious. Device is confirming to standard NFC 17 - 102 & UNE 21186.

Mounting arrangement : Device shall be mounted at least 5.0meter clear to highest point by support mast of 40mm dia GI pipe duly galvanised with minimum 85 micron zinc coating withfoundation to suit Mast.

The above Advanced New Generation ESE (Early Streamer Emission) technology consist of the following:

Air Terminal : Providing of early streamer emission air terminal made of pure stainless steel grade A316 double layer(DIN4301).

Mast- Providing of extension support mast made of 40mm dia class A GI pipe duly galvanized suit mast for Level-4 protection of 60m radious(as per NFC17-102)

Lighting Flash Counter(LFC): Providing fitting and testing of LFC / search counter upto 6 digit display, suitable for 10kA-100kA to be installed on one of the down conductors approximately 5.0m from the ground level. It registers every lightning discharge intercepted by the air terminal as direct lightning protection.

Protective Sheath: A 3" dia approximate 3.0m long plastic pipe is fitted at the ground level to prevent accidental shocks to human beings/ animals during lightning discharge.

Tripod Earthing System for ESE Technology Lightning Conductors-3 nos per set.

Supply and Fixing of 16mm dia molecularly bonded with copper on mild steel 2.4 m long(3 nos) as vertical copper electroded into three separate earth pits and joined at the top as per crow feet or delta configuration by three nos. clamps and digging, earth cutting and refilling of earth upto 600mm below ground level, chemical compounds called 'terec" is mixed with soil etc. for tripod maintenance free earthing system for ESE technology lightning conductor. The chemical compound for per set is 5kg. CRIC i.e 6 bags.

Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years.

Chemical Earthing Supply, erection and commissioning & testing along with earth cutting, digging earth filling for chemical earthing of the building .

Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years. Also provision of masonary enclosure 300mmX300mm withCI cover plate having locking arrangement as earth chamber.

Specification:

Polution free earthcon compound-25kgs

Electrode-2 m long, 17mm dia with 250 micron molecularly bonded with copper coated.

HDPE earth pit cover

( Detail of earth pit: UPS room-2 nos, lift machine panel-4 nos, Rising mains-4 nos, EPABX machine- 2 nos)

Main LT Panel for Collectorate Building :- Supplying, designing, manufacturing, installation, testing and commissioning of LT Panel of 14 SWG CRCA sheet (2 mm) steel , dust and vermin proof with reinforcement of suitable size iron channel size - 100 mm x 100 mm x 6 mm with proper lifting arrangement effecting proper connection of all incomer and outgoing(IP-43) fully compartmentalized cubical type, floor mounted , totally enclosed, extendable on both sides, switch board and suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50 kA with front operated construction including separate fabrication arrangement for fixing A.C.B. and Bus Coupler. The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized. Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for all ACB, Bus coupler, M.C.C.B.

The panel includes 415V, 1600A, 3Ph, 50kA, 50Hz Electrolytic Aluminium Bus Bar (E91EWP) Aluminium Earth Bus with removable glands plates, cable glands and sending and receiving ends, including connection with outgoing Feeders complete in all respects. All inter connections shall be made with 4, 6, 10 & 16 Sq mm PVC Cu. wire.

All incomer ACB and bus coupler shall be mechanically operated drawout type and with microprocessor communicable release. All 4 pole MCCB with thermomagnetic based release must have following character:

Icu=100% Ics with adjustable S/C and O/L

Provision for inbuilt earth leakage module & provision for inbuilt measuring unit.

Incomer:

1000A FP / ACB with handle (50kA)

Outgoings:

630A FP/ 36kA-2nos( 1 for normal rising main and 1 no for DG)

400A FP/ 36kA-2 nos( 1 for APFC panel and 1 for Essential rising main)

630A TPN change over open execution and panel mounted type with front rotary handle.

200A FP/ 25kA, MCCB-3 nos.( 1 no. for fire pump, 1 no for UPS room SDB and 1 no spare)

100A FP/ 25kA, MCCB-3 nos.( 1 no. for outdoor feeder pillar and 2 nos. spare)

63A FP/ 16kA, MCCB-6 nos.( 2 nos. for lift machine panel, 1 no for pump house & 2 nos. spare)

3 nos -Digital voltmeter (0-500V) , 3 phase, class0.5. Make :- AUE / Universal / L&T / Esma.

3 nos-Digital Ammetesr (0-500A) 3 phase, class 0.5 . Make :- AUE / Universal / L&T / Esma.

3 nos CT 1250/5VA -5 class one Epoxy resin cast CT 1 Set. Make :- Kappa / Matrix / SG Electricals / EPICAST.

9 nos LED indicatore (RYB) of 220V. 1 Set of 3 nos Make :- ESSEN / L&T - ESBEE / Binay / Teknik

9 nos Fuse base with HRC Fuse Set of 3 nos. Make :- Legrand / L&T / Schinder.

Aluminium Bus Bar for Panel- Al E91EWP bus bar size( 50mmx 6mm )x 5 for each phase and (50mm x 4mm)x5 for neutral and 60mmx 10 mm for Al. bus earth, 1600A, 415V, 3Ph , 4W, 50kA, 50Hz, shall be heat shrinkable PVC sleeved(R Y B & N) after temperture & enclosure de-rating max. allowable temprture of bus bar shall be 90 oC. etc as required.

A.P.F.C. Panel (Capacitor Bank) Auto Mannual Type (APFC) Panel – 200 kVAR 14 Stage Capacitor Bank Details with mixed dielectric Ultra Heavy Duty Capacitors of following range :-

Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of A.P.F.C. Panel (Capacitor Bank / Auto Mannual) of 14 SWG CRCA sheet (2 mm) steel IP – 54 floor mounting cubical type Capacitor Bank Panel suitable for operation on 415V, 50Hz, 3 Ph. AC supply and fault level 50kA with approximate size – 2,600 mm (H) x 2,700 mm (L) x 800 mm (W) with front operated construction including separate fabrication arrangement for fixing A.C.B., M.C.B., Capacitors, Contactors etc.

The sheet steel under go minimum 7 tanks treatment followed by finishing powder coating of minimum 60 micron thickness duly compartmentalized with locking arrangement duly fixed on Base Channel with proper lifting arrangement size – 100 mm x 50 mm x 6 mm having accessories mounted inside the cubical panel, earthing with 2 Nos. earth studs and Capacitors having earthing arrangement.

All openings shall be covered by soft rubber gasket, enclosure shall be galvanized.

Panel shall have suitable cable entry from bottom and suitable arrangement for multi runs aluminum cables for A.C.B., and MCB. The panel includes 415V, 800A, 3Ph, 50KA Electrolytic Aluminium Bus Bar (E91EWP) size 2 Nos. 120 mm x 8 mm for per Phase, 1 No. 120 mm x 6 mm for Neutral with removable glands plates, cable glands at sending and receiving ends, including connection with Contactors and MCBs complete in all respects. All inter connections shall be made with 2.5, 4, 6, 10 & 16 Sq mm PVC Cu. wire.

The panel shall have type test certificates with short circuit and IP protection (C.P.R.I. Test)

Location : Electrical room

Bill of Material in A.P.F.C. Panel :-

400A TPN / MCCB (36kA)- 1 no

Make:- Legrand - DPX / L&T - Hager / Siemens / Schneider

10A TP / MCB / 10kA for 5 kVAR Capacitor-4 nos

Make:- Legrand (Lexic) / L&T (D - Series) / Siemens / Schneider

16A TP / MCB / 10kA for 7.5 kVAR Capacitor-2 nos

Make:- Legrand (Lexic) / L&T (D - Series) / Siemens / Schneider

25A TP / MCB / 10kA for 15 kVAR Capacitor-2 nos

Make:- Legrand (Lexic) / L&T (D - Series) / Siemens / Schneider

32A TP / MCB / 10kA for 20 kVAR Capacitor-3 nos

Make:- Legrand (Lexic) / L&T (D - Series) / Siemens / Schneider

40A TP / MCB / 10kA for 25 kVAR Capacitor-3 nos

Make:- Legrand (Lexic) / L&T (D - Series) / Siemens / Schneider

6A - DP MCB -1no

Make:- Legrand (Lexic) / L&T / Siemens / Schneider

6A - 4P MCB -1 no

Make:- Legrand (Lexic) / L&T / Siemens / Schneider

6A - SP MCB- 1 no

Make:- Legrand (Lexic) / L&T / Siemens / Schneider

Volt Meter 96 mm square (0 – 500V) (Analogue) -1 no Make:- Legrand / L&T / Siemens

Am Meter of different rating (max. 0 – 600A) (Analogue) -1 no Make:- Legrand / L&T / Siemens

C.T. of different ration (max. 600 / 5, VA – 5) (CL – 1) 1 Set (3 Nos.) Make:- Legrand / L&T / Siemens

LED Indicator R.Y.B. (220V) (R – 15 / Y – 1 / G – 1 = 17 Nos.) Make:- Legrand / L&T / Siemens

Fuse Base 20A with HRC Fuse 1 Set (1 x 3 = 3 Nos.) Make:- Legrand / L&T / Siemens

16A – 2 pole / 2 way Rotary Switch Make:- Legrand / L&T / Siemens

10A Toggle Switch SP – HT -14 nos Make:- Legrand / L&T / Siemens

RPM 14 APFC Relay Make:- Legrand / L&T / Siemens

Aluminum Bus Bar for Panel :-

BUS BAR : 800 AMP, 500 Volts, 3 phase 50 HZ TPN high conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 1.0 sq mm / amp. Bus Bar Size - (60 mm x 12 mm) x 4 Al. Bus Bar. The aluminium bus bar shall be with heat shrinkable PVC sleeved (Red, Yellow, Blue and Black as R.Y.B. & N.) after temperature and enclosure derating max. allowable temperature of bus bar shall be 90ºC.

Interconnection wires 2.5 Sq mm / 4 Sq mm / 6 Sq mm / 10 Sq mm

Auto Mannual Type (APFC) Panel – 200 KVAR 14 Stage Capacitor Bank Details with mixed dielectric Ultra Heavy Duty Capacitors of following range :-

(25 x 3) x 1 Set = 75 KVAR (Power Capacitor) Heavy Duty Make:- L&T / Schneider - Meher

(20 x 3) x 1 Set = 60 KVAR (Power Capacitor) Heavy Duty Make:- L&T / Schneider - Meher

(15 x 2) x 1 Set = 30 KVAR (Power Capacitor) Heavy Duty Make:- L&T / Schneider - Meher

(7.5 x 2) x 1 Set = 15 KVAR (Power Capacitor) Heavy Duty Make:- L&T / Schneider - Meher

(5 x 4) x 1 Set = 20 KVAR (Power Capacitor) Heavy Duty Make:- L&T / Schneider - Meher

Total - 200 kVAR

Capacitor Duty Contactors :-

For 5 KVAR – ML – 1.5 (20A) - 4 nos, Make:- Seimens / L&T

For 7.5 KVAR – ML – 1.5 (25A)-2 nos, Make:- Seimens / L&T

For 15 KVAR – ML – 2 (32A) -2 nos, Make:- Seimens / L&T

For 20 KVAR – ML – 2 (40A) -3 nos, Make:- Seimens / L&T

For 25 KVAR – ML – 2 (40A) -3 nos, Make:- Seimens / L&T

Note:- All above inspection for Transformer, V.C.B, L.T. Panels, A.P.F.C. Panels, External Lighting Panel, Feeder Pillar Panels etc by departmental Engineers.

200 kVA Silent D.G. Set :-

Supply, fitting, fixing, errection and commissioning along with civil foundation work of 200 KVA D.G. Set, 415 Volts, 3 Ph. Silent Diesel Engine driven generating set as per IS:1460 & IS : 13018 and alternator as per IS:13364 complete with sound proof company make canopy (Acoustic Enclosure suitable for 200 KVA D.G. Set.) with breaker panel (Standard Mannual Control Panel) and civil foundation work as per the norms of 200 KVA Silent D.G. Set with suitable arrangement for Al./Ar./C etc as required. (Make:- Sterling and Wilson Powergen Private Limited with MTU Engine SDGSC - 3 Cotroller / Kirloskar (GREEN) / Jakson Limited / Mitsubishi / Cater Pillar)

Supply of acoustic enclosure for 200 kVA CPCB approved Acoustic enclosure with 80 mm MS base plate, 2 mm CRCA sheet, 50 mm thick foam / 100 mm Rock Wool Insulation, 14 surface tank treatment, dully powder coated and painted with Briliant Blue colour with integrate Fuel Tank, services door, louvers (Fresh Air / Radiator), 1020 dia residential type Silencer, approx dimension L x W x H - 4500 mm x 2000 mm x 2350 mm, complete with following accessories :-

a) Fuel Tank.

b) Batteries and leads.

c) Residential Silencers.

d) First fill of lube oil.

e) AMF Panel.

f) AVM Pads.

In above supply item following work are also included :- i) Installation, fitting, fixing, testing and commissioning of the same. ii) Civil part for commissioning of D.G. Set. iii) Installation of Exhaust system for D.G. Set shall be as per Central & State Pollution Board Norms along with iron structure i.e. 5 mtr. above the height of nearest building. iv) Test run for D.G. Sets without load and with load (part wise ).

Supply of Control Breaker Relay Panel for having all type of meters (Voltmeter, Ammeter, KW/m, Hz/m) with suitable arrangement for 3 Run 300 Sq mm 3.5 Core Al. Ar. Cable etc as required. Note:- Technical specification of above 200 KVA Silent D.G. Set shall be provided at the time of work order.

Supply, installation of 500 kVA TRANSFORMER( Level -2 as per IS:1180-2014)

Supply, installation, testing, fixing and commissioning in correct alignment position, effecting proper connections of continuous rating Energy efficient , Level-2, 500 kVA, 11/0.433KV, Off Circuit, oil cooled, copper wound, outdoor Transformer along with civil foundation work as per required size & length of MS channels as per the norms of 500 kVA Transformer with all accessories as per IS:1180-2014, air filled cable box suitable for 11KV 1 Run, 3 Core 120 Sq mm XLPE Al. Ar. Cable and LV termination box shall have suitable arrangement for 1.1 KV, 3 Run, 3.5 Core, 300 Sq mm XLPE Al. Ar. Cable etc as required. (Make:-GTB/ Volttam / Kirloskar / Raychem RPG Pvt. Ltd.)

Apart- from the above standard fittings followings items should be included:-

1. Oil Temperature indicating with One Set of Contacts.

2. Winding Temperature indicating with One Set of Contacts.

3. Marshaling Box with complete wiring.

4. Magnetic Oil Level Gauge with Contacts.

5. Bucholz Relay with set of Contacts and Shut off Valve.

Tests: - Routine test as per IS: 2026

Type Test: - Type test shall be conducted, if there is any charge then mention in the price bid.

Test Certificate: - Two Copies of test routine certificates have to be submitted along with the OCTC Transformer.

Transformer Size:- 3760 mm (L) x 3340 mm (B) x 2645 mm (H) approx or as per conpany specification.

The technical specification of Transformers are as follows:-

Rating - 500 KVA

Installation - outdoor

No of Phase - Three

Primary Voltage - 11 KV

Secondary Voltage - 433 V

Vector Group - DYn–11

Taping in Primary - + 5% to – 10% in 2.5 steps

Type of Tap changer - OCTC

Insulation class - A

Cooling - Onan

Temp. rise @ 50 Deg. C. Ambient

Oil by Thermo Meter :- 50 Degree C.

In winding by Resistance :- 55 Degree C.

Impedance :- 6.25% subject to IS Tolerance

Paint shade - Enamel Painting as per IS standard / Powder Coating / Conforms to IS 335

First Filling of Oil - HV – Cable Box

Terminal Arrangement - LV – Cable Box

CRGO Core used shall be of M/3 Grade in the Transformer

Copper wound.

Inspection - Before tanking and after tanking along with all testing.

Outdoor Type Cubical Feeder Pillar :-

Supplying, designing, manufacturing, installation, testing and commissioning in correct alignment position, effecting proper connection of all incomer and outgoing of outdoor type cubical feeder pillar of suitable size not less than 30 cm and up-to 45 cm deep made out of M.S. sheet 2 mm thick (14 SWG) duly compartmentalized, double door with locking arrangement (IP-54), duly fixed on MS angle iron frame work of size 50mm x 50mm x 6mm, 90 cm long legs earthing with two nos. earth studs, powder coated with rain shed structure etc as reqd. Panel Size - 1,150 mm (H) x 900 mm (L) x 400 mm (W), Based on MS angle iron frame - 150 mm x 50 mm x 6 mm. All inter connections shall be made with 2.5, 4 & 6 Sq mm PVC Cu. wire. The above panel consisting of the following:- ( 2 Nos. for Street light, 4 Nos. for Gadina light, and 1 No. for Swiming Pool) total :- 7 Nos.

Bill of Material in Feeder Pillar

Panel size and drawing shall be handed over at the time of work order.

100 AMP FP MCCB (25 KA) with handle (incoming) - 1 no, Make:- Legrand / L&T / Siemens

63 AMP FP MCCB (25 KA) (outgoing)- 3 nos.

Make:- Legrand / L&T / Siemens

Power Contactor of single pole of suitable rating - 3 nos, Make:- Legrand / L&T / Siemens

Astronomical Timer ref. 04676 - 1 no

Make:- Legrand / GIC (L&T) / Siemens

Voltmeter Analouge type (0 - 500V)- 1 no, Make:- Legrand / L&T / Siemens

Ammeter Analouge type (0 - 100A) - 1 no, Make:- Legrand / L&T / Siemens

CT 110/5 VA - 5 (CL -1) 1 Set - 3 set, Make:- Legrand / L&T / Siemens

Fuse Base with HRC Fuse 20A, 3 Set , Make:- Legrand / L&T / Siemens

LED Indicator RYB 220V 3 Sets, Make:- Legrand / L&T / Siemens

Incoming cable size :- 35 Sq mm 3.5 C Al./Ar/ Cable

Bus Bar 100A , 500V, 3Ph, 50 Hz, TPN High Conductivity electrolytic Aluminium bus bar of suitable length, insulated by heat shrinkable sleeves. The current density of bus bar shall be minimum 1.0 Sq mm / Amp. Bus bar size - (25 mm x 4 mm) x 4 Al. bus bar.

Chemical Earthing

Supply, erection and commissioning & testing along with earth cutting, digging earth filling for chemical earthing of the building .

Soil Treatment-Earth enhancing soil treatment compound TEREC + having essential chemical ingredients, such as ionic chemicals, dispersion chemicalhydroscopic chemicals to be provide stable low resistance for earth terminal to make it maintenance free for over 15 years. Also provision of masonary enclosure 300mmX300mm withCI cover plate having locking arrangement as earth chamber.

Specification:

Polution free earthcon compound-25kgs

Electrode-2m long, 17mm dia with 250 micron molecularly bonded with copper coated.

HDPE earth pit cover

( Detail of earth pit: Transformer-4 nos( 2 for neutral+ 2nos for body), DG-4 nos, LT panel- 2nos, Outdoor F/P- 2 nos and pump house-2 nos)

Supply and laying of 1000 mm x 600 mm x 12 mm thick chequered Rubber Matting of tested quality to with stand 15kV dielectric strenght as per IS:5424 complete in all respects.

Supply of 11 KV grade Rubber Hands Gloves. As per IS:4770.

Supply of First Aid Box with all necessary materials and medicine as approved by Indian Red Cross / St. Jhon's conforming to IS:2217.

Supply and fixing of Shock Treatment Chart with glass in Aluminium frame and to be fixed on wall in Bengali, Hindi and English.

Supply and fixing of 11 KV / 415V Danger Board as required.

Fire Extinguisher : Supply and fixing of carbon dioxide(Co2) type fire extinguisher of 4.5 kg as per IS: 2828

Providing fitting,fabrication of MS angle of section 50mmX50mmX6mm size for 40 m PCC trench to make support of MS iron plate to be fixed on every after 300mm in PCC trench.For Electrical room

Providing fitting,fabrication of MS plate of 12mm thick for covering PCC cable trench on the support of iron angle each piece of MS plate shall be 600X800mm. For Electrical room

Pump Motors For Pump House :- Supply, fitting, fixing, installation and commissioning of 3.7KW / 5HP / 3Ph / 400V / 2850 RPM electric motor complete set monoblock type along with base channel and civil foundation work, section - 2.5" and delivery - 2" excluding delivery and suction pipe, to be installed at pump house. (Make:- Kirloskar / Crompton / G.E.C.)

Supply, fitting, fixing, installation and commissioning of automatic DOL starter for 3.7kW / 5HP motor pump of 440V to be installed at pump house. (Make:- L&T / Siemens)

Providing and fixing PTMT flange 15mm size 56mm dia suitable for 15mm taps and weighing not less than 5gms of apporved ISS make

Providing and fixing PVC Pipe fittings with all accessories (supreme make)

i) 110 mm Door Tee (Supreme) P.V.C.

ii) 110 mm Plain Bend (Supreme) P.V.C.

iii) 110 mm Door Bend (Supreme) P.V.C.

iv) 110 mm 45 degree offset (Supreme) P.V.C.

v) 110 mm Cowel (Supreme) P.V.C.

vi) 110 mm Plain Trap (Supreme) P.V.C.

i) 75 mm Door Tee (Supreme) P.V.C.

ii) 75 mm Plain Bend (Supreme) P.V.C.

iii) 75 mm Door Bend (Supreme) P.V.C.

iv) 75 mm 45 degree offset (Supreme) P.V.C.

vi) 110 mm Plain Trap (Supreme) P.V.C.

Providing and fixing ball valve (full brass, KEC / APAR/ ZOLLOTO make) all complete . B)32mm nominal bore,

Providing and fixing Sprinkeler for Irrigation (full brass, KEC / APAR/ ZOLLOTO make) all complete . B)32mm nominal bore,

Voice Solutions SITC of EPABX SYSTEM: IP based 100% non-blocking EPABX System should be a IP Compatible with rich feature set of the system and can be connected with pure Voice over IP (VoIP) communication network across corporate Local and Wide Area Networks (LAN and WAN) as & when required. Central Processing Unit: The system main software should be open architecture based. The CPU of main system shall be 32 bit processor working at 2.0 GHz or better. The system should be rack mountable. • System Architecture should be latest pure IP and should be wall Mountable  Meet-me conference 30 party X 2 from day 1 must be available. Must Support Unified Communications Equipped with 368 Analog Extensions expandable upto 384 Extensions,16 Analog Trunk Ports, 1 PRI with 1 IP Phone to be Used as Opertor Console with 6DSS Keys, 02 Ports Auto Attendant,EPABX Make: Avaya/NEC/Unify

Analog Basic CLI Push Button Telephone: SITC of analog telephone- Make: Panasonic/ BPL/Beetel

SITC of Telephone Tag Block): IP-65( weather proof). Preffered Make-Krone

50 pair krone Box fully loaded without IPM

400 Pair krone Box fully loaded without IPM

600 Pair krone Box fully loaded without IPM

SITC of multi-core telephone jelly filled armoured PVC cables of conductor size 0.5 sq.mm annealed tinned electrolite grade copper , PVC insulated twisted pairs bunch togeather over all PVC sheathed , Laid on tray or along the wall or laid in pipes or in trenches including excavation of cable trench, sand filling covering with bricks and back filling complete as required. Make: Polycab/ Finolex/ Deltron/Havells/Anchor50 Pair

SITC of white modular plate type Single front plate for 1 Nos. RJ 45 Data outlet (Make:Legrand/Panduit/RIT/Siemon)

SITC of 3 Phase Online 60 KVA UPS with required nos of 12V SMF 120 AH battery ,Rack & Interconnecting cable UPS to battery (10mtrs) for Connected PCs ;Details of UPS: Technology:Mirco processor based controls, true online, double converson type, should have cold start facility Overall Efficiency :>90% Isolation ; Built in isolation transformer at the output of UPS system Charger: Should have built in charger of minimum 10 Amp VAH required :- Minimum 48960 VAH for 60 KVA Display: Should have LCD Display with event logging facility Should have auto phase reverse sequence operation.Should have SNMP (Simple Network Management protocol) compatability. Upgradeability: Should have upgradable to work as parrallel redundant UPS in load sharing mode Software communication: Should have SNMP compatibilty(Optional) Preffered Make-Vertiv/GUTUR/APC

UnitsDetailed Specs of 60 kVA UPS

Environmental Characteristics

Operating Temperature ºC 0 to 40

Maximal temp. for 8hr day 40 ºC

40°C (derate power by 1.5% per °C between 40°C and 50°C

Mean Temperature for 24hr Maximally 35

Relative Humidity≤95% at 20°C

Altitude of operation ≤ 1000m asl

Storage/ transport temperature -25 to 70 ºC

Height 1615

Width 715

Depth 810

Weight 670

Ventilation By internal intake fans

Airflow 1280

Cable entry Bottom side

Rated Mains Voltage 380, 400, or 415

Supply Three phase without neutral + Earth

Input voltage tolerance -15, +10

Frequency 50 or 60

Input Frequency tolerance 45~65

Rated input power 73.4

Rated input current 106

Maximum input power 81.1

Maximum input current 117

Duration of progressive power walk-in 5~300

Voltage range for Inverter operation 320~490

Recommended number of Leadacid cells 192 (380Vac), 198 (400Vac), 204 (415Vac),

Recommended float charge voltage 2.25 V/cell 432,(380Vac), 446 (400Vac), 459 (415Vac)

Recommended boost charge voltage 2.35V/cell 451 (380Vac), 465 (400Vac), 479 (415Vac)

Maximum voltage on manual charge 2.40 V/cell 460 (380Vac), 475 (400Vac), 490 (415Vac)

End-of-discharge voltage 1.67V/cell 320 (380Vac), 330 (400Vac), 340 (415Vac)

Max boost charge duration 480~1800

Freshening charge duration1~36

Boost-float threshold current 0.001C~0.025C

Ripple voltage superimposed ≤1

Charging current at 0.9 PF load 15

Rectifier output current rating 150

Rated mains voltage 380, 400, 415

Supply Three phase with neutral

Frequency 50 to 60

Rated Power at cosΦ = 0.8 60

Rated Power at cosΦ = 1 54

overload capacity For 101%-110% - 60mins, For 111%-125% - 10mins, For 126%-150% - 1mins

Maximum non linear load allowed 100% Pn

Voltage stability, steady state test ±1

Voltage stability, transient test ±5

Maximum rate of change of frequency 0.1

Rated mains voltage 380 - 400 - 415

Supply Three phase with neutral

Rated Current:,380 Vac, 400 Vac,415 Vac 91,86,83

Bypass voltage toleranceDefault upper limit: 15%; default lower limit: -20%

Delay time to recognize bypass voltage returned to window 2

Inverter output voltage window ±5

Frequency 50 or 60

Input frequency tolerance ±10

Maximum frequency slew rate 1

Current rating of neutral cable 1.4 x In

Protection, bypass line The bypass line should be protected using an external device in the input distribution system. This device should be sized to discriminate with the load protection

Transient overload 10 times the rated current for 100 ms

Rated power 60

No load losses 1.3

Full load losses (100%) 4.8

Digital Conference System Wireless Access Point along with all hardware and soft ware with all required equipments and components complete set. Make:- BOSCH DCNM-WAP/ Harman/BOSE

The ‘Wireless Access Point’ (WAP) shall be used as a standalone central control device for wireless connection and control of the Wireless Devices. , The WAP shall have the following features: • Easy to use, • Truly wireless, no need for an additional WiFi router for tablet control. • Easy and intuitive web interface for system setup, configuration, control and licensing. • Native support for camera control. Zero Interference, • Seamless automatic wireless frequency channel switching; up to 44 channels in the 2.4/5 GHz band. • Packet Loss Concealment to mask the effects of lost or discarded packets.Standard WiFi

For giving a clear visual overview of the proceedings. • A maximum of six HD Conference Dome cameras can be connected to the system with native support. General Web interface

• The WAP shall support the following software functions, which shall be available through the web interface (Some functions shall be not supported when a tablet device is used). Configuration

• User management shall give the possibility to create several users with user specific access to functionality. • 5 band parametric equalizer.• Camera control and HD-SDI switcher configuration. • Wireless network SSID and WPA2 settings. • Wired network host name setting (DHCP and zero config protocol based on Bonjour,

Total Cost of Digital Wireless Conference System Wireless Access Point

Digital Conference System Wireless Contribution Unit (Chairman Unit). Make:- BOSCH DCNM-WD/ Harman/BOSE

The ‘Wireless Device’ shall enable participants to take part in a discussion by speaking into a microphone, (when it is activated) and listening to proceedings via the built-in loudspeaker or connected headphones.

The Wireless Device shall have the following features and benefits: • Possible to speak indicator. • Request to speak indication in microphone. • Single use, dual-useor chairpersoncan be configured via the web interface. • Audio mute button. • Operating in the 2.4 GHz and 5 GHz (UNII1, 2 (extended) and 3) (license free) band.

The Wireless Devices shall accommodate two headphone connections and controls (on the left andright hand side), so the speaker can be heard clearly even with excessive background noise.

Separate battery pack, easy to change & charge.

Microphone button with a red or green illuminated ring. Red indicates microphone is active, green indicates request-to-speak accepted.

Uni‑directional microphone on adjustable stem, Built‑in plop and windshield

Low susceptible for mobile phones,

For acoustical challenging rooms

Battery Pack for Chairman Unit

Pluggable long microphone, length 480 mm (19.9 inch), silver

Total Cost of Digital Conference System Wireless Contribution Unit (Chairman Unit)

Digital Conference System Wireless Contribution Unit (Delegate Unit). Make:- BOSCH DCNM-WD/Harman/BOSE

The ‘Wireless Device’ shall enable participants to take part in a discussion by speaking into a microphone, (when it is activated) and listening to proceedings via the built-in loudspeaker or connected headphones.

The Wireless Device shall have the following features and benefits: • Possible to speak indicator. • Request to speak indication in microphone. • Single use, dual-useor chairpersoncan be configured via the web interface. • Audio mute button. • Operating in the 2.4 GHz and 5 GHz (UNII1, 2 (extended) and 3) (license free) band.

The Wireless Devices shall accommodate two headphone connections and controls (on the left andright hand side), so the speaker can be heard clearly even with excessive background noise.

Separate battery pack, easy to change & charge.

Microphone button with Red or green illuminator. Red indicates microphone active, green indicates request for speech accepted.

Uni‑directional microphone on adjustable stem, Built‑in plop and windshield

Low susceptible for mobile phones,

For acoustical challenging rooms

Battery Pack for Contribution Unit

Pluggable long microphone, length 480 mm (19.9 inch), silver

Total Cost of Updated Digital Conference System Wireless Contribution Unit (Delegate Unit)

Charger for 5 Battery Packs. Make:- BOSCH-DCNM-WCH05//Harman/BOSE

Analogue Conferencing System in 2 Nos. Meeting Hall(Main Conference Hall and SP Meeting Hall) Speaker solutions and amplifications:-

Providing of Corded Digital Deligates Units Gooseneck microphone with programmable switch . With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times , Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Immunity to mobile phone interference Make & Model is: Bosch- CCSD-DL./Harman/BOSE

Providing of Corded Digital Deligates Units Gooseneck microphone with programmable switch With Specifications such as: Frequency response:200 Hz to 12.5 kHz. -Headphones load impedance:> 32 ohms < 1k ohm, -Loudspeaker nominal output:72 dB SPL, - Length of microphone :480 mm (18.9 in), - Plug and play functionality for ensuring fast installation and reconfiguration times Immunity to mobile phone interference and with Features such as: Possible-to-speak indication, Request‑to‑speak indication, Built-in loudspeaker with volume control, Built‑in 3.5 mm (0.14 in) stereo headphones socket, Built‑in volume control for headphones, Color-coded LED indicator above microphone button, for showing the following states: microphone on, request‑to‑speak, and possible‑to‑speak, Chaiman Button Make & Model is :Bosch- CCSD-DL./ Harman/BOSE

Providing of Digital central conference controller with Built‑in MP3 recorder with internal memory and USB recording, Built‑in Digital Acoustic Feedback Suppression, Quick and easy connection upto 80 discussion devices, Native support for automatic HD camera control, Signal to noice :> 94 dBA, Frequency response for input :30 Hz to 20 kHz, Recording/ Playback (bit rate):64, 96, 128, 256 Kbit/sec, Nominal loudspeaker output:72 dB SPL and Functions such as: Plug-and-play functionality, Web browser control, Open microphone control, Built-in MP3 recorder, Discussion control Make & Model is: Bosch-CCSD-CURD/ Harman/BOSE

SITC of Mixer 10 channel Analog Mixer suitable for the prescribed solution Make-Souncraft/AKG/Yamaha/Bosch/BOSE ;

SITC of wall mounted cabinet speaker 30 Watt includes mounting system Dual 4" 2‑Way Surface-Mount Loudspeaker,Compact full range,Ideal for Conference Halls, patios, and retail,Vented LF enclosure,1-inch titanium diaphragm HF driver with neodymium magnetic structure,Coherent Coverage Waveguide,Full-bandwidth overload protection (LF and HF),Elliptical weather-resistant ABS enclosure,Paintable black or white finish,Magnetically shielded for video applications,Strong-Arm Mount™ for easy, flexible aiming,"T" version for 70 or 100 V distributed systems with specifications of Frequency Range (-10 dB)- 65 Hz – 20 kHz, Sensitivity (SPL, 1 W/1 m)- 89 dB,Max. SPL/1m (calc.)- 115 dB,Power Handling (Continuous, Peak)- 100 W, 400 W,Transformer taps(transformer version only)- 70 V: 3.75 W,70 V/100 V: 7.5, 15, 30 W, Coverage, H x V- 120° x 80°, LF Transducer-Two 4", HF Transducer -1", Nominal impedance-(non-transformer version)- 8 Ω, Dimensions (H x W at front x D) -12.2" x 6.9" x 8.5",(310 x 175 x 216 mm) ; Make- AKG/BOSE/EV

SITC ofHandheld Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice)

SITC of Headworn Wireless Mic with Cardiod polar pattern for transmitter,Dynamic microphone with Neodymium magnet , Receiver frequency response 80Hz-18kHz,Receiver RF sensitivity < 1.0 µV,Receiver Image rejection>55dB,Receiver Dyanmic range >95dB and receiver having 32 channels possible,Receiver S/N ratio >100dB A,distortion <1 %, Transmitter sensitivity - 3.2 mV/Pa,modulation:+/-40kHz (Approved Makes: Audio Technica, Senheiser, Electro-Voice)

SITC of required cables & Accessories for Conference Halls

6u Network Equipment Rack 600X 600 with power socket, amplifier support, exhaust fan, etc.Prefrred Make- Valrack/Rittal/President

SITC Speaker Cable 2 core 2.5 Sqmm PVC coated and PVC sheathed multistrand copper flexible unarmored FRLS cable; Make-KRYSTAL/Polycab

Mic Cable-Supply of 0.75 Sq. mm 2 Core Shielded Microphone Cable (100 m Roll); Approved make- Krystal

SITC of Wooden Podium alongwith Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color of make-Kramer/Crestron/Lightware/Magnum; Wooden Podium would be manufactured locally

SITC of Cable Cubby (One HDMI Cable, Two LAN Cable, Two unswitched AC outlet,One 3.5 mm Mini Stereo Audio Jack,Compact size with square bezel Black color of make-Kramer/Crestron/Lightware/Magnum;

SITC of HDMI Cable-2 Mtr;Make- Krammer/Wyrestorm

SITC of Projection screen :- high gain ,Best quality Motorized ProjectionScreen with Remote ,133",16:9 with viewing area of 65” x 116”; Make: Liberty/Da-Lite/Draper

SITC of Projection screen :- high gain ,Best quality Motorized ProjectionScreen with Remote ,110",16:9 with viewing area of 54” x 96”; Make: Liberty/Da-Lite/Draper

SITC of Ceiling mounting Kit For Projector; Preferred Make- Liberty/Raymax

Projector: 4,300 lumens WXGA high brightness compact projector Display System: 3 LCD system Size of effective display area: 0.75”(19mm) x 3 BrightEra LCD Panel Aspect ratio 16:10,Number of pixels : 3,072,000 (1280x800 x 3) pixels Throw Ratio :1.10:1 to 1.79:1,Zoom – Ratio : Approx. x 1.6,Contrast ratio (full white / full black) 20000:1 *2,Speaker: Speaker 16 W (monaural) INPUT A : RGB / Y PB PR input connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack INPUT B: RGB input connector: Mini Dsub 15 pin female Audio input connector: Stereo mini jack INPUT C: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support INPUT D: HDMI input connector: HDMI 19-pin, HDCP support Audio input connector: HDMI audio support,S VIDEO IN : S Video input connector: Mini DIN 4-pin VIDEO IN: Video input connector: Phono jack,OUTPUT : MONITOR output connector: Mini D-sub 15 pin female Audio input connector: Stereo mini jack LAN : RJ-45, 10BASE-T/100BASE-TX,USB: Type-A & Type-B MICROPHONE IN: Microphone jack: Mini Jack,Display resolution: Maximum display resolution: 1600 x 1200 dots, fV:60Hz,Screen size : 30" to 300" (0.76 m to 7.62 m) (measured diagonally); Preffered Make-Panasonic/Hitachi/Sony

SITC of HDMI bidirectional RS232 and IR over high definition base1, Make-Kramer/Crestron/ Key digital

SITC of HDMI bidirectional RS232 and IR over high definition base1, Make-Kramer/Crestron/ Key digital

CCTV Surveillance. 4MP IR Bullet Fixed Camera -1/2.8"Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8 mm Fixed lens, 0.01 Lux at F1.2, 0 Lux with IR, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Hikvision

4MP IR Indoor Dome/Bullet Fixed Camera -1/3" Progressive Scan CMOS, 2688 × 1520 at 25fps, 2.8mm Fixed lens, 0.01 Lux at F1.2, ICR, ONVIF (PROFILE S, PROFILE G), support H.265, H.264, MJPEG, 120db WDR, 3D Digital Noise Reduction, Three individually configurable stream, 12 VDC & PoE, IR range: 40m, Support on-board storage up to 128 GB (SD card not included), IP67, IK10, Alarm & Audio: 1 input & 1 output, Edge Anlalytics- Line crossing detection, Intrusion detection, Motion detection, Scene change detection, Audio exception detection, video tampering, UL, CE, FCC certified.Preferred Make- Axis/Pelco/Hikvision

IP Fixed Mini Dome Camera: 1/2.7" Progressive Scan CMOS, ICR, 0.01 lux at F1.2, 0 lux with IR, 1920x1080:25fps, 2.8mm Fixed Lens, H.265, MJPEG, Three individually configurable stream, IK08, IP66, DC12V & PoE, 120dB WDR, 3D DNR, BLC, Support on-board storage up to 128GB (SD card not included), Alarm -1 input,1 output, IR range: up to 10m, Edge Anlalytics- Line crossing detection, intrusion detection, Motion detection,face detection, video tampering, UL, CE, FCC certified. Preferred Make- Axis/Pelco/Hikvision

SITC of 4MP 35× Network IR PTZ Camera with Dual-sensor, 1/1.8" progressive scan CMOS,Full-color image output,Up to 2688 × 1512 resolution,Min. illumination:Color: 0.0005 Lux @(F1.5, AGC ON),B/W: 0.0001 Lux @(F1.5, AGC ON),0 Lux with IR, 35× optical zoom, 16× digital zoom, 120 dB WDR, 3D DNR, HLC, BLC, EIS, Chromatic Defog, Support H.265+/H.265 video compression, Support rapid focus, Deep-learning-based target classification algorithm for auto-tracking 2.0 and perimeter protection, Up to 250 m IR distance. Smart IR, Rain-sensing auto wiper, IP67,White Balance-Auto/Manual/ATW (Auto-tracking White Balance ) /Indoor/ Outdoor/Fluorescent Lamp/Sodium Lamp,Lens 5.9mm to 206.5 mm, 35× Optical, Zoom Speed-Approx. 4.4 s (optical lens, wide-tele),Field of View-Horizontal field of view: 58.9° to 2.2° (wide-tele),Vertical field of view: 35.3° to 1.2° (wide-tele),Diagonal field of view: 65.9° to 2.5°(wide-tele),Working Distance-10 mm to 1500 mm (wide-tele),Aperture Range-F1.6 to F4.4, Movement Range (Pan) 360° endless, Perimeter Protection-Intrusion, Line Crossing, Region Entrance, Region Exiting, Support alarm triggering by specified target types (human and vehicle),Filtering out mistaken alarm caused by target types such as leaf, light, animal, and flag, etc.,Event Detection--Unattended Baggage Detection, Object Removal Detection, Face Detection, Audio Exception Detection,Motion Detection, Video Tempering Alarm, Exception (HDD Full, HDD Error, Illegal Login, IP Address Conflict, Network Disconnected),Smart Tracking-Manual Tracking, Auto Tracking (support tracking specified target types such as human and vehicle), Event Tracking,Smart Record,ANR (Automatic Network Replenishment), Dual-VCA, ROI Main stream, sub-stream and third stream respectively support eight fixed areas.Protection Level-IP67 Standard. Lightning protection, surge protection and voltage transient protection meets IEC61000-4-2-2/3/4/5/6 Preferred Make- Axis/Pelco/Hikvision

SITC of 128 ch Smart Network Video Recorder: Connect Up to 128 IP Cameras, Dual OS, Should support N+1, Hot spare, Up to 12 Megapixels Resolution, Two independent HDMI and one VGA Output, HDMI outputs of 4K resolution, VGA outputs upto 1080, Support H.265, H.264, MJPEG, Incoming Bandwidth 750 Mbps, Support RAID0, RAID1, RAID5, RAID 6, and RAID10, ANR Technology, 24 SATA interfaces for 24 HDDs and capacity of each HDD upto 8TB, 3x USB with two USB 3.0, Alarm I/O 16/8, RS-485, 4 RJ-45 10 /100/1000 Mbps self-adaptive Ethernet interface, Multiple network monitoring: Web viewer, CE, FCC, UL certified.Preferred Make- Axis/Pelco/Hikvision

SITC of 6TB Surveillance Grade Hard Disk for NVR for 30 Days Back up; Make-Seagate/WD

Surveillance class Common Micro SD Card 128GB for camera; Make Hikvision/Axis/Pelco

75" 4k LED Panel,Preffered Make-LG/Samsung

Fabrication, Supplying, Installation, Testing & Commissioning of electrical control panel of cubical construction, wall mounted type, fabricated out of 2mm. thick CRCA sheet, compartmentalised with hinged lockable doors, dust and vermin proof, powder coated of approved shade after 7 tank treatment process, cable alley, interconnection, and accessories mounting and internal wiring, earth terminals, numbering etc. complete in all respects, suitable for operation on 415 V, 3 phase 50 HZ AC supply with enclosure protection class IP 42.

For Terrace Pump

Air release Valve / Drain Valve

MS Structure support for piping

Supplying and fixing of hose cabinet of size 450mm x 450mm x 250mm made of 2mm thick M.S. sheet with 6mm thick glazed glass door including necessary locking arrangment suitable to accomodate 1 nos. 15 mtr. long hose pipe, 1 no. branch pipe mounted on wall or raised brick platform and duly painted with post office red externally and white internally with synthetic enamel paint complete in all respect.

Providing and fixing 25 mm nominal gun metal gate valve class I with CI wheel of approved quality with union (Screwed end)

Providing , fixing Dry Chemical Powder (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 20oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (4 Kg Capacity)

Carbon Di-oxide Type , Gas Confirming to IS ‘15222’ , Cylinder Confirming to ‘IS 7285’ & PESO approved ,Controllable Discharge Mechanism, Discharge Hose & Horn As per ‘IS 15683’ & ‘IS 2878’ ISI mark Fire Extinguishers (Wheel Type or Squeeze Grip Type). Operating Temperature :- (-)20oC to (+)55oC Suitable for ‘B’ ‘C’ Class of FIRE (4.5 Kg Capacity)

Providing , fixing Modular type Fire Extinguishers for electrical rooms (Stored Pressure Type) Mono Ammonium Phosphate 50% powder confirming to ‘IS 14609’ , Nitrogen Pressurized, Controllable Discharge Mechanism, Pressure Gauge, Discharge Hose & Nozzle Epoxy Polyester Powder Coated As per ‘IS 15683’ ISI mark Fire Extinguishers. Operating Temperature: - (-) 10oC to (+) 55oC Suitable for ‘A’ ‘B’ ‘C’ Class of FIRE complete in all respects (5 Kg Capacity)

Providing and laying 19mm dia PVC conduit complete with required junction boxes in recessed / surface system PVC insulated copper conductor cable of 2x1.5 sq.mm. in existing conduit as required. Make:Polycab/Mescab

Providing and fixing check valve (NRV) complete with companion flanges, bolts, nuts, rubber insetions etc.

Pressure Gauge Assemble with Gate/Ball Valve

Supply , stacking & filling of good Earth all complete as per building specification and direction of E/I.

Providing and Displaying Hyphorbe Lagenecaulis 115 to 180 cm ht., well developed 12 and above good color fresh and healthy leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Nolina recurvata well developed with fresh & healthy 35 to 40 lush green leaves in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and Displaying Ficus Benjaminatopiary well developed with fresh & healthy 5 to 6 ball specific size and shape 120 to 150 cm ht in 40 cm Cement Pot as per direction of the officer-in-charge.

Providing and stacking of Lawsomnia inerme(of height 60-75 cm. with 4-5 branches in bag of size 25 cm as per direction of the officer-in-charge.

Providing and dispalying seasonal/ Annuals flowers in full bloom well developed fresh and healthy plant in 25-30 cm Earthen pot/ Plastic Pot and as per direction of the officer - in - charge

Add 18% GST

Add 1% Labour cess 1%

HEIGHTEN CONSTRUCTIONS

M/S PRASAD CONSTRUCTION & CO

RAJBIR CONSTRUCTION PVT. LTD.

M/S B.P.CONSTRUCTION

Bidder Name

M/S B.P.CONSTRUCTION

NIRANJAN RAI